Providing of Kiosk Shop and Waiting Shed Arrangement at New Bus stand Near Ulavar Santhai North Zone Ward13

Amount

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating as per Design given by the departmental officers etc, complete as per standard specification

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed

Plain Cement Concrete 1:2:4 (one cement, two fine aggregates and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Supplying and filling in foundation and basement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Brick work in CM 1:5 (one cement & five M-Sand) using Country bricks of size 83/4"x41/4"x23/4"including finishing, curing, etc., complete complying with standard specification -

Plastering with cement mortar (1:5) 12mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Painting Two Coat with Ready Mixed Enamel Paint over the new Iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc (ROLLING SHUTTERS (WITH ISI MONOGRAM)) (Manual Operator)

Painting two coats with ready mixed Exterior Emulsion Paint approved quality and colour including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Wiring with 2x1.5sq.mm. PVC insulated unsheathed FRLS SC copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A FT switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light / fan point (forelectronicregulator) (5 points per coil)

Wiring with 2x1.5 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150x100x113mm TW switch box for 5A 3pin non inter locking Wall socket with 5A flush type switch with painting of suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for open PVC plug point

Wiring with 2x4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor cable of 1100V grade in suitable pipe on wall and ceiling with PVC accessories with 150mmx100mmx113mm TW switch box for 15A 3 pin non inter locking wall socket with 15A flush type switch with painting of suitable colour with continuous earth wire connection of 4 sq.mm copper wire for open PVC power plug point

supply and fixing of 30W LED street light fitting with LED (Higher end) with 25 mm dia. GI pipe (class B) with 1 no. 25 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting

Supply and fixing of TNEB meter board suitable for 32 A single phase service connection with 32 A fuse unit (500V) 32 A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20PVC insulated copper wire from EB meter to fuse unit with 1No 40 Amp30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connection

Supply and fixing of 40 A FP MCB Isolators including all charges etc, complete as per standard specification (VOL 1 with Index

Supply and fixing of 25 Amps 30 MA DP RCCB / ELCB including all charges etc, complete as per standard specification. (VOL 1 with Index

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 1200 mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator, with 1 metre down rod with fan clamp with side plates and cross arm of size 450 mm (18")

Supply and run of 2 of 4sq.mm.(56/0.3)PVC insulated SC unsheathed copper conductor of 1100V gradein 25mm dia GIpipe(Class'B') suitably bent at both ends with necessary angle iron upright and end supports formains

Supply and run of 2 of 4sq.mm.(56/0.3)PVC insulated SC unsheathed copper conductor of 1100V gradein suitably bent at both ends with necessary angle iron upright and end supports formains

MJ INDUSTRIES (BID ID -1207099)