8484/E8 SPECIAL REPAIR TO BLDG NO T-90, T-465, T-466 AND T-468 OF JCOs AND OR GOVT MD ACCN AT MTTC AREA OF 506 ASC BN UNDER GE (EAST) BAREILLY

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer - in - Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

Taking down shutter and refixing with easing in same opening of any description exc. 1 sqm but n.exc 2 sqm each complete all as specified and directed

Dismantling of 100mm bore cast iron/ pvc drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Dismantling of 75mm bore cast iron / pvc drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed .

Taking up or down15 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

Taking up or down 20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

Dismantling water tanks 500 & n exc 1000 and removing to store of all retrieved material complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement for fixing tiles etc complete all as specified and directed

M & L 25 mm thick PCC 1:2:4 type B0, using 12.5mm graded aggregate as in floors to receive surface of tile complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L Non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8 mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles complete all as specified and directed

M&L for non skid ceramic tiles 7 to 8 mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm on vertical surfaces etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles complete all as specified and directed.

M & L 7 to 8 mm thick glazed coloured ceramic tiles ( square/ rectangular) with border , area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L 20 mm thick Granite of black colour (tablee rubbed and polished) as in windows cill & cooking platforms and like in 15mm cement mortar (1:4) screed bed including form work , pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as spd as directed

M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

M& L 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed

M&L Sand filling under floors or in foundation including watering and consolidation complete all as spd

M&L for cement Concrete coloured interlocking paver blocks shall be factory made with casting in rubber/pvc moulds & compacting on a vibro table assembly and shall be cured in curing tank for atleast 14 days and then air dried before use. The paver block shall be confirming to IS 15658 -2006 of 60mm thickness, M-35 Grade. Approved design, shape, size and colour of top layer complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L for reinforced cement concrete M-25 (20 mm graded aggregates) (nominal mix) (nominal mix) as in slabs supported on wall like including bonding agent , complete all as specified (reinforcement to be measured & paid under respective items). (nominal mix) as in slabs supported on wall,landing, balconies, shelves and like including bonding agent , complete all as specified (reinforcement to be measured & paid under respective items).

M&L form work to chajja, weather shade, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified.

M&L form work to edges of concrete flats, treads, breaks in floors window cill, concrete railing opening in conc wall , floor and roof n.exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20cm wide for rough finished surfaces of concrete, complete all as specified.

Supply and fix TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0, complete all as specified.

M &L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregrate laid over roof, kerbs or mud stops, rounded or chamfered finished even and smooth without using extra cement complete all as spd and directed.

supply Integral water proofing Liquid

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as spd as directed

M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry finished even and smooth witout using extra cement complete all as specified and directed.

M& L for rendering 10mm thick in cement mortar (1:4), and 5 mm thick setting layer in CM1:3 finished even and smooth using extra cement to on brick masonary wall surfaces or on other than fair faces of brick masonary finished even and smooth without using extra cement with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed.(Note : Water proofing liquid shall be measured and paid separately)

Dismantling timber scantlings 40 Sqcm and over in section, in any position , framed work complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) insulation boards / slabs / blankets of any thickness, including cover fillets complete all as specified and directed.

M&L for Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc GDE Fe 410-S. complete all as specified and directed.

M&L for E-board false ceiling consisting of powder coated GI wall angle, main T and cross T of 25mmX 25 mm X 1.40 mm thick grid frame work, joist, angle/ Tee as directed and mild steel wire hook not less than 6 mm dia with arrangement for adjusting height of ceiling and including provn of 4 mm thick E- Classic board in pannelof size 600X600mm with necessary off cut including dismantling of existing false ceiling and taking down and refixing of Electric fitting carefully complete all as specified and directed.

S&F for Pressed steel frames Size 125mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and directed

S&F Flush shutters, 30 mm thickness solid core construction, with block board core and plywood face panels, commercial type on both sides Face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed by Engineer-in-Charge. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring. Fixed in floor complete all as specified and directed

S&F for 18 mm thick termite resistant and water proof, both side prelaminated wooden plywood one side with decorative choice lamination, and other side plain white lamination total thickness not more than 22 mm thick, as in cup board shutters, with wardrobe/ finch lock & PVC lipping on all exposed edges of same texture and shade, with complete all as specified as directed. Note:1) Design & layout of wardrobe and pattern / colour of lamination to be approved by GE. 2) thickness of laminated not less than 1mm for inside plain white type & 1.5 mm for outer decorative type. The laminate shall be fixed to base with approved adhesive as per manufacturer's instructions and machine pressed to ensure proper bonding with base ply and avoid air pockets. 3) Frame to be fixed to walls, soffits & base of cupboard with fasterners.

S & F for aluminium powder coated frame hollow sections members of size 63.50 mm x38mmx 1.48 mm thick,4 mm thick aluminium composite panel LDPE core with PET coating fixed with into the wall for kithen cabinet/ cupboard shelf incl hanging self for clothes with aluminium clip/strips, pvc beadings fixed with adhesive on edging , design as per site requirements basis, complete all neccessary fitting all as specified and directed

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet , suppling & fixing in opening as per specification & drawing complete all as specified and directed

S&F 30 mm thick factory made both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed

S&F mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding complete FE-290 grade E-165 all as specified and directed.

S&F Powder coated aluminium ventilators box type with louvers & wire mesh fixed with neoprene rubber gasket, aluminium beading, clips. Frame made with powder coated aluminium section of size as appended below (i) frame :45.2mm x35mm X 1.15 mm (ii) Aluminium beading - 0.7mm thick (iii) Glass louvers depth 6 inch. Blade Angle: 38 degrees and thickness of blade 2.02 mm with 106.25 mm spacing. (iv) Aluminium neccessary fittings complete as required. (v) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S&F Powder coated aluminium sliding windows and frame with movable shutter ( sliding on minimum two PVC roller of best quality on two tracks Aluminium composite panel shutter fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :68.4x38mm X 1.15 mm thick for two tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iii) Aluminium beading - 0.7mm thick (v) Aluminium fittings such aluminium suitable handle with auto interlock cap with suitable size . (vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S&F magnet catch with striking plate including letting in and fixed, complete all as specified.

S & F 300 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed

S & F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed

S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed.

S&F 100 mm size butt hinges medium weight stainless steel colled rolled complete all as specified and directed by Engineer-in-Charge.

S&F 300mm size ordinary mild steel , rat tailed rod pattern spring including roller and roller plate welded to mild steel frame.fixed in repair complete all as spd & directed.

S&F 300 mm long aluminium sliding door bolts plate type with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed

S & F hydraulic concealed hinge with clip on installation and integrated Silent System, opening angle not less than 100º, For shutter thickness 15 - 24 mm full overlay type shutters, hinge cup dia 35 mm including necessary fixing arrangement with SS screw complete all as specified & directed.

S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S&F 1000 litres, rotational moulded polyethylene of white colour in tripple layer water storage tank (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system ), hoisted and fixed in position complete all as specified and directed

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia steel water tubing galvanized medium grade concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F 20 mm dia steel water tubing, galvanized, medium gradeconcealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed

S&F in repairs Brass chromium plated wall mixer 2 in 1 , 15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls complete all as specified and directed

S&F in repair fancy type 15mm dia chromium plated fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes complete all as directed.

S & F in repair fancy type 150mm size square brass CP shower rose all as specified.

S&F in repairs 15 mm dia bib tap fancy type chromium plated with flange quarter turn complete all as specified as directed.

S&F in repairs 15 mm dia bib tapcast copper alloy with butterfly handle , screwed down for iron pipe or for brass ferrule and fixed complete all as specified as directed.

S&F in repairs vitreous chinaware coloured wash hand basin with pedestal. complete including fancy CP pillar tap, CP Waste coupling ,waste pipe ,complete fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed by Eng in charge.

S&F stainless steel of AE - SI 316 grade tubular towel ring including apair of CP brass bracket complete all as specified.

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm , complete all as specified.

S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified.

S&Fin repair fancy type stainless steel towel rack size 600mm including apair of brass bracket complete all as specified &directed by Engr in charge.

S&F chromium plated brass tubular towel rail 20 mm dia, D type for wash hand basin centre holed fixed to iron pipe complete all as specified and directed.

S & F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified.

S&F in repair fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified .

S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S&F in repair 15 mm dia fancy type stop cock , chromium plated with long shank and cup (conncelaed type)for iron pipe or for unions and fixed complete all as specified and directed

S&F in repair vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified.

S&F in repairs, PVC low level flushing cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed

S&F in repair PVC (SWR) multifloor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed by Engr-in-charge.

S&F in repair PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fittingcomplete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F in repairs Stainless Steel plate rack of size 90x80x25cm made with 1.00 mm thick sheet including taking out existing wooden plate rack, complete all as specified.

S & F for 0.8 mm thick stainless steel kitchen sink size 590x460x230mm undermount, single bowl (bowl size 540x410x230 mm) , incl waste pipe & SS coupling,

S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy type droppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support complete all as specified and as directed

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding door,Fixed with angle cleats or other connecting plates

S&F Pre-coated galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified.

S&F Pre-coated galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified.

M & L for cutting chases of hanging chajjas, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of sunshades, shelves, lintels, Chajja ( up to IInd floor) etc making good, cutting out exc 10cm and not exc 40cm girth in RCC chajjas in brick walls complete all as specified and as directed.

M&L for dubbing coat on exposed cement concrete 10 to 20 mm cement plaster 1:4 incl micro concrete with chicken wire mess with water proofing liquid @200 ml per bag up to II nd floor roof level complete all as spd as directed

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted wooden or wood based surfaces of any description n.exc 10 cm in width or girth when unconnected with other painting or when painted in a diferent tint and applying one coat of synthetic enamel paint over and including one coat of red oxide complete all as specified and directed.

M&L for complete removal of existing treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism ) with sanding pad of appropriate grit to make surface clean ,free from dust ,loose paint etc by skilled labour and applying two coat OBD on wall with airless electric sprayers over a coat of primer applied using airless electric sprayer over one coat of plaster of paris of 1mm thickness complete all as specified and directed. Note:-Application to be done through authorised applicator of manufacturer.

M&L for two coat OBD on newly plastered wall surface with airless electric sprayers over a coat of primer applied using airless electric sprayers over one coat of plaster of paris putty of 1mm thickness complete all as specified and directed. Note-Application to be done through authorised applicator of manufacturer

Demolition of Reinforced Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

M & L for two coats of elastomeric compound i.e super latex of Dr fixit Pidifin 2K/ Pidilite-302 super latex / Fosroc-brush crete / Cico Tape Crete on concrete or brick masonary surface after cleaning (vertical or horizontal) by removing all the loose mortar laitance dirt, dust etc by chisel, hammer, wire brush, jute, brush and air blower. complete all as specified and directed.

M&L for preparation of new surface of plastered and applying of two coat OBD on ceiling with airless electric sprayers over a coat of primer applied using airless electric sprayers over and including 1 mm thick plaster of paris (approved by GE)prepared and sanded with electrically operated sanding machine. Application to be done through the authorised applicator of manufacturer complete all as specified and directed.

M&L applying two coat of white putty on new surface and applying one coat of exterior water based primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by jpaint manufacturer and as mentioned in PS and accessories fpr applying distemper, should be able to spray in hard to reach areas and penetration of distemper, on the surface to achieve excllent application using limited manpower complete all as specified and directed.

M&L for complete removal of existing treatment, preparation of old decorated plastered or unplastered surfaces of walls / roof projections including facia,cornices etc. and applying two coat of white putty and applying one coat of primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by paint manufacturer and accessories for applying Primer, should be able to spray in hard to reach areas and penetration of Primer, on the surface to achieve excllent application using limited manpower complete all as specified and directed. Note : - Sanding of old decorated surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer.

M&L for applying two coat of Antifungal weather coat exterior wall finish applied by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying exterior weather proof paint, should be able to spray in hard to reach areas and penetration of exterior weather proof paint on the surface to achieve excellent application using limited manpower complete all as specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing all retrieved materials to MES stores for segregation of serviceable /Unserviceable fitting&fixture and also making good disturbed surfaces of wall, floors etc complete all asspecified and as directed by the Engineer-in-Charge.

M&L point wiring complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through & including PVC Conduit (Concealed in wall/ceiling) of size 20mm dia and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fittings / junction boxes / inspection covers etc, with and incl concealed MS sunken box of suitable size flush with wall surface, suitable for fixing of Modular type switches / sockets etc, complete all as specified and directed for the following :- Note : 1. Modular white cover plate shall be measured and paid separately 2. Rate quoted shall deemed to be inclusive of cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed.

All as per item No 113 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 113 above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 1132 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sq.mm size complete all as specified and directed

S&F Modular Switch 1 way 16 Amps, 1 Module size complete all as directed..

S&F Modular Socket 6 A, 2/3, Pin 2 Module size complete all as directed..

S&F Modular Socket 6A/16 A, 5 Pin ,2 Module size complete all as directed..

S&F Modular Switch 1 way 6 Amps, 1 Module size complete all as directed..

S&F Modular Bell push 6A 1 module

S&F electric call bell ding dong AC 230 volts Single Pole.

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing angular lamp holder, metal cased body of brass with back plate in batten fittings, including Plastic square box of required size complete all as specified and directed by the Engineer-in-Charge

S&F LED Bulb 9 Watt

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

Supply and fixing in replacement LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

S & F in replacement LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size..

S&F in replacement of street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 nos MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer, complete all as directed.

S&F in replacement LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection, complete all as specified and directed by Engineer in charge.

Supply and fixing in replacement sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 12 way with 200 Amps rated bus bar complete complete all as specified and as directed by the Engr-in-Charge..

Supply and fixing in replacement SPN 40 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning.

Supply and fixing in replacement SP 5 to 32 amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR 2020 Part-I and connecting to MCBDB’s earth test point all as specified or indicated including testing on completion .

Supply and fix exhaust fan made of iron body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc

Taking down the old serviceable electric meter and keeping in safe custody including refixing the same including necessary electric wire, flexible pipe and PVC conduit from DB to Meter and fixing accessories required as per site requirement complete all as specified and directed by Engr-in-Charge

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

M & L Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of size 6 sqmm all as specified and directed by Engr-in-Charge.

Please Enable Macros to View BoQ information