SPL REPAIR TO BLDG NO P-383 IN RESPECT OF 12 CORPS ZONAL WKSP AND OTHER SANCTIONED WORKS AT ARMY AREA UNDER THE AREA OF AGE B/R-II OF GE (ARMY) No 1 JODHPUR

Dismantling barbed wire fencing & removal from site complete all as directed

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling post or struts (wood, steel or RCC) any section, including taking out embedded portion in concrete and making good the disturbed ground complete all as specified and as directed by Engr - in - Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

Excavating in post holes (of similar holes) each n. Exc. 0.50 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering and removing surplus soil to a distance n. Exc. 50m and making good surface complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft / loose soil complete all as specified and as directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out dense/hard soil complete all as specified and as directed.

Removal of excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed.

M&L for Plain cement concrete 1:4:8 type D-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete, in flooring path, sub foundation etc, complete all as specified and as directed .

M&L for plain cement concrete 1:3:6 type C-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete for fencing post, foundation for embedding the post ,as in surface chasnnels and drains etc,complete all as specified and as directed .

M & L for Precast cement concrete 1:2:4 type B1 (20mm graded aggregate) solid block masonry exc. 10 cm in width and setting in cement mortar 1:4 complete all as specified and as directed by Engr - in - Charge.

M & L for 25mm thick Plain Cement Concrete Type B0 1:2:4 (using 12.5 mm graded stone aggregate) in sub base, floors, pavings complete all as specified and directed by Engr-in-charge.

M & L for Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc including over 15 mm thick screed bed or bedding layers in CM (1:4) for laying in floors finishing complete all as specified and directed.

M&L for non-skid coloured ceramic tiles joint free 7 to 8mm thick (Square/Rectangular) area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match including over 15 mm thick screed bed or bedding layers in CM (1:4) for laying in floors finishing ,complete all as specified and directed.

M&L for glazed colour ceramic tiles (premium quality) of size 300X450X6-7 mm, as in vertical surface such as i.e. dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 10mm thick backing coat in CM (1:3) complete all as specified and directed.

Taking down existing cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M & L for rendering 15mm thick in CM 1: 4 on stone masonary surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for rendering 10mm thick on fair faces concrete surfaces in CM 1:3 and finished even and smooth in ceilings without using extra cement complete all as specified and directed by Engr-in-charge.

M & L for rendering 15mm thick in CM 1: 6 on stone masonary surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M & L for preparing new plastered surfaces of walls and applying two coat of Oil Bound distemper over 2mm thick wall care putty over a coat of alkali resistant primer and complete all as specified and directed by Engr-in-charge.

M & L for preparing new plastered surfaces of ceilings and applying two coat of Oil Bound distemper over 2mm thick wall care putty over a coat of alkali resistant primer and complete all as specified and directed by Engr-in-charge.

M & L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by Engr-in-charge.

M & L for complete removal of existing treatment and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified and directed by Engr-in-charge.

Taking down Chowkats or frames not exceeding 1.5 Sq. M each (Without taking off shutters from the frames) complete all as specified and directed by Engr-in-charge.

Taking down Chowkats or frames exceeding 1.5 Sq. M each and n exceeding 4.0 Sqm each (Without taking off shutters from the frames) complete all as specified and directed by Engr-in-charge.

S & F Pressed steel frames for doors with one or more rebates incl necessary fixing lugs, hinges, size of frame 165 x 60 mm complete all as specified and directed by Engr-in-charge.

M & L for PCC (1:2:4) type B0 using 12.5mm aggregate for filling in pressed steel frame concrete shall be compressed all as specified and directed.

M&L factory Made flush shutters, 40 mm thick solid core with block board core construction as per IS 2202(part-I, 1999), both side decorative type lamination. The stiles & rails shall be with out any joint and made with non- coniferous timber hard wood (Hillock/ Mirantee/ Bosum/ Benteak) with moisture content not less than 12% as per IS. The face panel comprising of ply wood or cross band and face veneers shall be glued by hot pressed process. The over all finished thickness of face panel shall not be less than 35mm while the thickness face veneer shall not be less than 0.6 mm complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantFactory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: (a)-For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (b)- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

Taking down steel window / ventilator complete all as directed.

M&L preparation of steel and steel base surfaces over 10 CM width or girth and applying two coats of synthatic enamel paint over one coate of red oxide primer complete all as specified and as directed by Engr - in - Charge.

S & F powder coated Anodised aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with aluminium section weighing 0.55Kg/m with one or more rebates or for sliding windows (2 track / 3 track), ventilators with louvers having suitable mechanism for tilting, U shaped fillets etc complete all as specified and directed.

S & F powder coated anodised aluminium door shutters (minimum thickness of powder coating 50 micron), aluminium section weighing minimum 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, 2 tower bolts, 1 mortice lock of vertical type brass 4 levers size 65mm and anodised aluminum snap beading screws etc complete all as specified and directed.

S & F pre powder coated aluminium decogrill all as per sample fixed to aluminium framework of windows & ventilators complete all as specified and directed.

S&F powder coated anodised aluminium window shutters prepared for sliding or hanging or fixed type etc with aluminium sections weighing minimum 0.55kg/m incl necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws and also including handles, tower bolts, locks and hinges etc complete all as specified and directed by Engr-in-charge.

S&F Aluminium (Extruded section body Door closer hydraulically regulated, designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S & F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engr-in-charge.

S & F 100 mm long medium weight, cold rolled Stainless steel Butt hinges complete all as specified and directed by Engr-in-charge.

S & F Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 140 mm complete all as specified and directed by Engr-in-charge.

S & F 4mm thick Figured glass, pin headed type to be fixed in louvers of ventilators in small widths complete all as specified and directed by Engr-in-charge.

S & F 3mm thick Sheet glass, ordinary quality and glazing with oil putty/wooden beads in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed by Engr-in-charge.

S & F in repairs mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.00 mm with necessary fitting on steel / wooden surface complete all as specified and directed by Engr-in-charge.

S&F in repairs decorative type curtain rod stainless steel finish of pipe 22 to 25 mm dia with best quality knob metal with double fitting type including stainless steel brackets (trade pattern) fixed to walls complete with two nos decorative stainless steel knobs (fincals round type with mirror optic finish) at each end , sample as approved by GE, complete all as specified and as directed

S&F in repairs vitreous China wash down water closet pan European type pedestal pattern, white with seat and cover including PVC 'P' or 'S' trap, flush HDPE pipe of 32 mm dia and PVC connection 15mm size & 450 mm long with PTMT nuts & fixing arrangement of cistern, complete all as specified and as directed.

Dismantling of cast iron of AC / PVC soil, waste & vent pipe jointed in cement mortor of size 110/100mm bore, incld. All fittings, complete all as specified & directed.

All as per item No. 48 here-in-above, but 75mm bore.

Supply & laying 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches of suitable size complete all as specified and as directed .

Supply & laying 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches of suitable size complete all as specified and as directed .

S&F of 110 mm bore (SWR) PVC bends any radius , complete all as specified and directed.

S&F 110mm bore PVC [SWR] branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F 110mm bore PVC [SWR] branch piece, double (double Y) equal or unequal complete all as specified and as directed.

S&F of 75 mm bore (SWR) PVC bends any radius with access door, complete all as specified and directed.

S&F 75mm bore PVC [SWR] branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F 75mm bore PVC [SWR] branch piece, double (double Y) equal or unequal complete all as specified and as directed.

S&F of PVC (SWR) floor trap plain with grating including jointing with solvent cement dia of outlet 75mm, complete all as specified and directed.

M & L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement etc complete all as specified and directed.

S&F in repairs 25mm stop valve, cast copper alloy with screwed down high pressure with crutch or butterfly handle both ends screwed for iron pipe or for union & fixed of 25mm dia complete all as specified and directed.

S&F angle stop valve with wall flange 15 mm bore of pipe, brass chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed including taking down old stop valve complete all as specified and directed by Engr-in-charge.

S&F in replacement two way angular stop cock with wall flange, chromium plated brass, fancy type 15mm dia complete all as specified and as directed.

S & F CP Hand Shower (Health Faucet) with 8mm dia, 1.2 Mtr long flexible tube & wall hook with N.R.V (Back flow preventer), 15 mm dia complete all as specified and directed.

S&Fof 10 ltrs capacity PVC valve less, ISI Marked syphonic action type, flushing cistern, low level, with Anti Bacterial Knob, with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia and, cistern colour shall be match WC colour, complete all as specified and as directed.

S&F Rotational moulded polythene water storage tanks of 1000 ltrs capacity, white three layered (ISI marked) (Cylindrically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I with PTMT ball valve high pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms complete all as specified and as directed.

Supply only integral water proofing compound etc complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store etc complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store etc complete all as specified and directed.

S&F of CPVC pipe SDR 11 having outer dia 20 mm with plain CPVC SDR 11 fittings such as bends, elbows, unions and end pieces to receive the fittings, concealed in walls/ceiling or lay in floors, complete and fixed with solvent complete all as specified and as directed.

All as per item No.69 here in before but 16mm outer dia pipes.

Taking down existing damaged/loosed cement concrete /bricks tiles from roof /terrace to a depth of average 50 mm including taking down of existing APP membrane if any cleaning with water and depositng of debris to a distence exceeding 500m complete. (For Roof Surfaces where old PCC padding is not be demolished and fresh PCC padding not to be provided), etc complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-0 (using 12.50mm graded stone agg) over roof for making good depression/undulation and as in roof kerb rounded or chamfered on edges to match the existing , complete all as specified and directed.

M&L for rendering 20mm thick in screed bed or bedding layer in CM (1:4), mixed with integral water proofing liquid all as per manufacturer's instructions over concrete surfaces finished even and smooth with out using extra cement. (WPC shell be measured and paid separately under respective item of schedule).

M&L for carrying out water proofing treatment with UV stable single component fibre reinforced elastomeric liquid applied waterproofing membrane having solid content of 55% formulated wih PU hybrid polymers and reinforcing acrylic fibres and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat (6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/10 sqft in two coats (10-12 hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongationat break of 350%, crack bridging ability of 2.5 mm @650 microns thickness, resists positive hydrostatic pressure of up to 10 bars. The material shall be appliied with brush or roller, complete in all respect as per the direction of Engr-in charge/consultant. Also, proper surface preparation along with covingat corners is must, complete all as specified and as directed. Note : - (i) The work shall be executed by the authorized applicator of the manufacturer only. (ii) The authorized applicator of manufacturer shall be approved by GE. (iii)The color of final finish shall be decided by the GE

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified & directed.

S&F for Aluminium snap grid frame work of 605 X 605 mm panel size of pre powder coated pre fabricated GI section including hangers for false ceiling along the Walls suspended with, including S&F of 600mmx600mm size ceiling board of PVC laminated gypsum board 10-12mm thick and fixed as per manufacturers instruction as per approved sample complete all as specified and as directed.

S & F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing etc complete all as specified and directed.

S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing etc complete all as specified and directed.

S & F rolled mild steel in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe 410-W(Gde E-250) quality A, etc complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base to floor, incl well compacting & laid to levels etc, complete all as specified and directed.

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

S&F counter type Vitreous china wash basin white/coloured size 630X450 mm including 15mm bore swan neck pillar taps cast copper alloy chromium plated fancy type, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shank and fly nuts, screwed for iron pipe fixed with CP waste coupling 32mm and waste pipe complete all as specified and directed.

S & F in replacement Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) etc complete all as specified and directed.

S & F Vitreous China Urinal, Half stall type, white including providing and fixing of plugs bedding against wall in CM 1:2 pointing around urinal back in cement mortar complete all as specified and directed.

M&L 18 to 20 mm thick black granite stone as in WHB counter top, cooking platform, treads of steps, jambs, pillars, window cills & similar nature works, machine cut, (table rubbed and polished) best quality as per sample, over & including 15 mm thick screeding in CM1:4 including rounding & double mouldlng with jointless finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, providing suitable dia hole in the slab for the gas pipe, complete all as specified and as directed.

M&L for rounding to edges of stones slabs one edge , such as in steps, cooking platform, and other similar situations etc, complete all as specified and as directed.

Demolition of brick / block or stone / boulder masonry walling built in cement mortar including all quoins arches pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and as directed.

M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

All as per item No. 89 here-in-above, but except stone

Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed.

Taking down carefully cement concrete / spalled out concrete from RCC roof projections, ceilings, sunsheds, beams etc upto cover depth by chipping out lightly including necessary scaffolding etc complete all as specified and directed.

M & L for 5mm thick rendering in CM 1:3 & finishing the surface even & smooth without using extra cement complete all as specified.

S & F GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as directed.

M & L for raking out joints/ pointing to to squared rubble masonry, jodhpur type regular course built in CM 1:3 all as specified.

M & L for keyed pointing to square rubble masonry Jodhpur type regular course in CM 1:3 all as specified.

S & F in repair Soap dish, chromium plated, any type, as approved fixed with brass screws or embedded in wall complete all as specified and directed .

S & F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) etc complete all as specified and directed.

S&F in repairs Corner glass shelf 250mm superior quality with CP tubular framing & brackets complete all as specified and directed.

Supply and laying machine / factory made kerb stone of M-25 grade,at or near ground level, cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.

M&L Machine cut kota stone slab 20 to 25mm thick as in floor laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including M&L 15mm thick screed bed in CM 1:4, complete all as specified and as directed.

M&L for preparing newly plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of primer, Priming the plastered and other surface with alkali resistant priming paint complete all as specified and as directed.

M&L for PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in coping/ benching, DPC, pier caps, bed blocks, for hold fast etc., including mixing with WPC and necessary form work, complete all as specified and as directed. Note:- WPC shall be measured and paid separately.

S&F M.S Angle iron, flat iron, hand rails, or other steel section or posts and struts in fencing drilled and countersunk for balusters running bars, nosing to steps including embedding in concrete and screwing etc. flate iron to angle iron post including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe 410-0 or Fe 310-0 complete all as directed and specified.

M&L for Framed work as in doors or gates of angle or other section, Fe 410-W (Gde E250) quality-A with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

M&L for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, each screwed end to be fitted with washers and one haxagonal or square nut not exceeding 5cm long with dia of neck 5 to 10 mm complete all as specified and directed.

Supply only MS galvanised chain link fencing of any size or type(size as approved by GE) complete all as specified and as directed. Note:- Weight of chain link will be determined by BOO constituted by GE.

Fixing only mild steel galvanised chain link fencing including line wires, any mesh size and type to any type of standards, rails, straining bolts etc including provn of binding wire if reqd etc complete all as specified and directed.

S&F MS tie round bars 10mm dia and over, cut to length, bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and incl mildsteel wire annealed not less than0.9mm dia or securing with clips quality conforming to grade FE-410 all as specified and confirmed etc complete all as specified and directed.

M&L Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and directed.

S&F 2 to 3mm Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

M&L for face work masonry with 100-125mm thick white/chitter sand stone having rock face bushings not less than 15-20mm incl chisel drafted margin 20-25mm wide all as per local Jodhpur pattern (KADAOU) regular coursed well bonded bedded & solidly hearted built in CM 1:4 complete all as specified. Height of Kadaou stone course shall not be less than 200mm all as directed at site etc complete all as specified and directed.

M&L for sand stone moulded weathered copings, window cills & the likes set in CM 1:6 with corbelling, throatings all as per design complete all as specified.

M & L for keyed pointing to kadaou facework of Jodhpur sandstone in CM 1:3 using white cement & pigment to match the shade of stoneetc complete all as specified and directed.

Taking down old sand stone/precast cement concrete chattri over all size 0.6x0.75x1.2m and removed away from siteetc complete all as specified and directed.

M&L for fixing in position of Sand stone chattri Jodhpur pattern octagonal shape each side of length 45 to 45cm & height not less than 0.75m (excluding dome) incl 8 Nos sand stone columns, sand stone arches, brackets & sand stone dome slab of minimum 75cm height of approved shape & carvings incl 1 No brass finials of height 0.30m complete all as per trade pattern of interlocking & fixing of parts with suitable solvent cement adhesive etc complete all as specified and directed.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc.complete all as specified and directed

M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed by Engr - in - Charge.

M&L RCC nominal mix type B1 1:2:4 (using 20 mm graded granite stone aggregate) in foundations including rafts, footings and mass concrete complete all as specified and as directed.

M & L RCC nominal mix type B1 1:2:4 (using 20 mm graded granite stone aggregate) in Columns, piers, posts and struts complete all as specified and as directed by Engr - in - Charge.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns hooking ends cutting bending and binding with mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and as directed.

S & F Mild steel TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed by Engr - in - Charge.

M&L for providing precast cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) as in kerb stone etc (of any section as approved) with plain faces, incl chamfers, weathering, throating etc and setting in CM 1:4 complete with joints to match etc complete all as specified and directed.

Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site as directed.

Taking down carefully UNSV Submain wiring and Services cable of any size make, type and capacity and depositing at site as directed.

M&L for (concealed) point wiring complete with multistranded copper conductor 1.5 Sqmm PVC insulated unsheathed single core FRLS cable 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring, drawn through in and including non-metalic PVC concealed (including Cutting Chases and make good the distrubed surfaces as per existing finishes) conduit of size 20 mm or med grade as required as site, totally concealed in walls / and surface on floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FRLS PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, suitable for One light/fan/bell point controlled by one, one way switch, complete all as specified and directed. Note:- The rates of chase cutting on wall done concealed conduit & making good good the distrubed surfaces as per existing finishes and steel terminal boxes are included in the unit rates

All as per Sr. item No.129 here-in-above, but suitable for One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

All as per Sr. item No.129 here-in-above, but suitable for One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch .

All as per Sr. item No.129 here-in-above, but with using 2.5 Sq mm FRLS copper wire with 4 Sqmm FRLS copper earth wire for independent 15 Amp point.

S&F Switch piano type, single pole, one way, 5/6 amps, 230 volts, complete all as specified and directed.

S&F Socket, two-in-one, 5 Pin, 5 Amp, universal type, 230 volts, complete all as specified and directed.

S&F Switch piano type, single pole, one way, 15/16 amps, 230 volts, complete all as specified and directed.

S&F Socket, 6 pin, 15/16 Amp, multipurpose shutter type , 230 volts, complete all as specified and directed.

S&F and replacement of Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed.

S&F LED lamp 9W complete all as specified and directed by the Engineer-in-Charge.

S&F Ceiling rose, three terminals, bakelite body, 230 volts, complete all as specified and directed.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W,4 ft long, T-5 batten fitting, designed linear sleek aesthetic PVC housing, PC cover ensures soft and glare free lighting wide angle of 120 degree, upto (110Lm/W) complete all as specified and as directed.

S&F bldg security LED Light Luminaire of 35 Watts having IP 65 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts with in built surge protectore, toughened glass with and including GI pipe 40 mm bracket of 1.5 m in length including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable, complete all as specified and as directed.

S&F LED Luminaire 600mm x 600mm, 35/36 Watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

S&F Amp rating 240V, 10KA 'C' curve Miniature Circuit Breaker (MCB) of SPN 40 to 63 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning etc complete all as specified and directed.

Supply, fixing, testing and commissioning MCB, B Curve type, 10KA, upto 40 Amp, single pole with overload and short circuit protection, complete all as directed.

Supply & fixing as MCB DB DD SPN 12 Ways including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall incl dismantling of old UNSV DB etc complete all as specified and directed.

S&F factory made distribution board in sheet metal enclosure in double door with 200A rated copper bus bar, TPN 6 way, 415V, IP-43 & IK 09 Protection, duly fixed in concealed in wall including cutting chasing pinning, and making good, suitable for for fixing MCB's complete all as specified and as directed.

S&F MCB TPN, 125 Amps, breaking capacity 10KA, C curve confirming to IS/IEC 60898-1 2002, integrated label holder, sliding bottom clamp, IP 220 protected terminal, sliding shutters, 240 volts, 50Hz including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. complete all as specified and as directed.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cm x 60cm x 6mm thick burried directly in ground vertically at a depth not less than 2.25 metre deep below normal ground level with top edge of the plate not less than 1.5 metre below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt, filling in alternate layer and electrode connections by using galvanized iron earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers made of galvanized iron or steel and protected by light grade 15 mm dia GI pipe connected to main switch board or main control board, and GI pipe light grade 20 mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC 1: 2: 4 type C2 including excavation and earth work, disposal of surplus soil to a distance not exc. 50 mtr all as specified and as shown on Plate No 5 of SSR Part I (1991)incl dismanteling of existing unserviceable earth pit etc complete all as specified and directed.

Supply, laying testing in replacement, in trenches/on wall / in duct/ through protection pipe LT UG XLPE insulated, armoured, heavy duty electric cable, aluminium coductor, 1100 V grade,cross sectional area 25 sqmm 4 core incl retrieving / taking down/ taking out old unservisible cable from duct/trenches/pipe/pole/wall etc, complete all as diredted by Engr-in-charge. Note : Earth work and brick work measured and paid separately

Supply and laying unreinforced Precast concrete cable cover, class LV, type 1, flat size 300 mm x 180 mm x 40mm, complete all as specified and directed.

Supply and laying of sand for sand cushioning for cable protection in trenches including punning down of sand layer etc complete all as specified and directed. Note :- Punned thickness shall only be measured and paid.

S&F in replacement of GI tubing , light grade of 40mm bore with fittings as in road crossings for cable protection complete all as specified and as directed.

Taking down only ceiling fan (M.D supply) and connecting up including provision of cable from ceiling rose or connector to fan & all specified and directed by Engr-in-charge.

M&L for submain wiring with 2 runs of 6 sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to submain DB, drawn into separate concealed medium grade, ISI marked, non metallic PVC conduit 15mm dia size incl all conduit accessories & fittings/junction boxes/inspection covers etc with and incl cutting chasing and making good of disturbed surface of wall/floor/ceiling etc as original by brick work, plastering, whitewashing, OBD etc as required complete all as specified and directed. Note :- Two runs of 6 sqmm and one runs of 6 sqmm (earth wire) including one run of PVC conduit shall be measured as one length incl making good the disturbed surfaces for the purpose of measurement.

Note:- (i)- Qty's have been clubbed from 3 Nos sanction Job's, whose details as per appx NOTE:- (i)- The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount