SPECIAL REPAIR TO WATER DRAIN IN STOCKING WING AND UNIT AREA (FROM BLDG NO P-72 TO 74) AND BLDG NO 369/01 TO 04 (MD ACCN) AT MIL STN KOTA

Amount

Demolition of Stone slabs and tiles of any description or thickness in floors etc, laid, bedded and pointed in any mortar, complete all as specified and directed.

Dismantling of Stone sett paving of any description or thickness, laid dry, complete all as specified and directed.

Taking down cement plaster any description/thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Demolition/Dismantling of existing roof treatment, any type from RCC roof slab including lime concrete/PCC padding over roof, removing layer of bitumen under lime concrete/PCC padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside MD land, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL), complete all as specified and directed.

Demolition of brick work/stone boulder masonry, built in CM incl all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

Demolition of cement concrete (reinforced) such as roofs, floors (other than ground floors), beams, stair cases, landing, chhajjas and other similar works and removing rubbish from premises, complete all as specified and directed.

Dismantling mild steel work of any description not otherwise provided for, complete all as specified and directed.

Taking down chowkhat or frames not exc 1.50 Sqm each with shutters (without taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhat or frames exc 1.50 Sqm and not exc 4.00 Sqm each with shutters (without taking off shutters from the frame), complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each, complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm & n. exc 2 Sqm eachand refixing in same after easing and adjusting including renewal of screws etc complete all as specified and directed.

Demolition and breaking up drain pipes and fittings, salt glazed ware, AC, PVC or RCC, internal dia of pipe 100/75 mm, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

Taking down GI tubing 15 mm dia including cleaning for refixing or removing to store, complete all as specified and directed.

Taking down GI tubing 20 mm dia including cleaning for refixing or removing to store, complete all as specified and directed.

Dismantling water storage tank of any description of capacity exc. 250 ltr but n.exc. 500 ltr, complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying cables/pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in including spreading, leveling, watering and well ramming in layers not exc 25 Cm in soft/loose soil, complete all as specified and directed.

Removing excavated material (Surplus soil) to a distance not exc. 50 mtr and depositing where directed at level not exc. 1.5 mtr above the starting point, complete all as specified and directed.

M&L PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in foundation, filling, mass concreting etc, complete all as specified and directed.

M&L PCC 1:5:10 type E-2, using 40 mm graded stone aggregate, as in sunken portion, filling, mass concreting etc, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary formwork to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L Providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L RCC 1:1.5:3 type A-1 using 20 mm graded stone aggregate, as in slabs supported on walls, beams, columns etc, roofs, landings, deck slabs, shelves etc complete all as specified and directed.

M&L for RCC (nominal mix) 1:2:4 type B-1 using 20mm graded stone aggregate as in Chhajja, chullah hoods, weather shades, corbels, water troughs and similar items including edges complete all as specified and directed.

M&L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in surface channel and drains, complete all as specified and directed.

M&L precast (factory casted) cement concrete kerb stone casted in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate with plain or interlocking joints (as directed), making groove in ground of desired dimension, placing in position and set and jointed in CM 1:4, making good disturbed surface of ground, complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) 75 mm thick as in sub base, finishing the surface even & rough to receive topping layer, complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) 100 mm thick as in sub base, finishing the surface even & rough to receive topping layer, complete all as specified and directed.

Cutting chases pinning in, making good to facing where required and pointing in CM (1:3) to ends of edges of landings, shelves, cills, lintels, concealed water tubing etc and making good cutting, girth not exc 10 cm, in brick walls, complete all as specified and directed.

Cutting holes into or through brick walls exceeding half brick but not exceeding one brick thick, built in cement mortor and making good in cement mortor (1:3) or cement concrete (1:2:4) type B1 as required, complete all as specified and directed.

M&L brick work with fly ash old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls,built in CM 1:4, complete all as specified and directed.

M&L walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:4, complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, with maximum depression on face from straight edge held against the dressed surface not exceeding 40 mm; to block in course masonry (Lime or sand stone), complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (2 No.) suitable handle (1 No), complete all as specified and directed.

S&F in renewal factory made pressed steel cupboard shutters alongwith frame, frame made of 1.25 mm thick PBI sheet and shutter made of 1.00 mm thick PBI sheet with 6 Nos 3.15 mm thick and 100 mm long steel hinges per shutter, godrej pattern locking arrangement with 12 mm dia vertical rod and lock with duplicate key & chrome finish handle, duly spray painted in factory with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete with fastener, hold fast etc as required at site, complete all as specified and directed. (Total width including frame shall be measured for payment purpose).

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in- charge.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified, as shown on drawing and directed. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life).

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and directed.

S&F in renewals 19 mm thick prelaminated MDF board, exterior grade (Grade I, type 2), both side off white shade or shade as approved by Engineer in Charge, fixed as in shelf and partition of kitchen cabinet, complete all as specified and directed.

M&L for 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

M&L for 2nd class hard wood (Sal) glazed and skeleton shutters 35 mm thick, factory made, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (b); supplied and fitted to chowkhats complete all as specified and directed.

S&F continuous piano hinges, mild steel bright finish or electro galvanised, 30 mm width of flaps when open, complete all as specified and directed.

S&F 100 mm Hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S&F Wire netting of galvanised steel wire 2.00 mm dia fixed with tinned tacks of wire staples, size of mesh 20 mm, complete all as specified and directed.

S&F 300 mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

S&F 200 mm aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, medium weight, cold rolled and fixed with screws, complete all as specified and directed.

S&F 150 mm size aluminium handles, cast type, anodised, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F in renewal stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

Formwork (rough finished surfaces) Chhajja, chullah hoods, weather shades, corbels, water troughs and similar items including edges, complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for fair finished surfaces, complete all as specified and directed.

Formwork (rough finished surfaces) to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar works, not exc 200 mm thick complete all as specified and directed.

M&L mild steel TMT bars, 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S&F 1.00 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

M&L mild steel framed work as in doors or gates of angles or other section with gusset plates, rails braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with including either hooks and hinges or steel hanging door fittings (excluding of steel sheeting or other covering running rails and guides) and hanging also fastening and fixing, conforming to Fe 410-W (Gde-E- 250) quality-A, complete all as specified and directed.

S&F stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, dia of pipe 100/110 mm, complete all as specified and directed.

S&F stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, dia of pipe 75 mm, complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (using 12.5 mm graded crushed stone agg) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

M&L for applying 10 mm thick screed in CM 1:3 on roof slabs with using liquid water proofing compound as per manufacturer's instructions, complete all as specified and directed. (Liquid WPC shall be measured and paid separately).

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS 3384 @ of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of cold applied bituminous primer conforming to IS:3384 @ 0.40 Kg/Sqm.

Item 67.00 Contd........ (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm (minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. (v) Cost of above aspects is deemed to be included in quoted rates.

M&L for cleaning of walls and floor of sunken portions including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS: 3384 @ 0.40 Kg/Sqm, torching overlaps with a propane or a butane gas torch with an overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold applied bituminous primer all as per manufacturer’s instructions, complete all as directed. Note: (i) The waterproofing treatment shall be measured for floor area and shall be got carried out through the manufacturer or their authorized applicators only.

Supply only liquid water proofing compound as approved by the GE, complete all as specified and directed.

M&L for 25 mm thick plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in flooring/sub base, finished even and rough to receive floor finishes/screed, complete all as specified and directed.

M&L for green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including bull nosing to exposed outer edges and making 20 mm dia hole at appropriate place to facilitate gas pipe, set in CM 1:4 bedding and pointing with white cement mixed with pigment, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L granite slab 18-20 mm thick, table rubbed and polished in cooking platform, jambs, cills, pillars, tread, risers, platform for WHB etc including bull nosing to exposed outer edges and making 20 mm dia hole at appropriate place to facilitate gas pipe, set in CM 1:4 bedding and pointing with white cement mixed with pigment, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300x250x7mm/ 450x300x7mm thick as in vertical surface such as skirting/dado and riser to step etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface laid over and including 10 mm thick CM 1:4 backing, complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size made with grey cement and pigment, confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, laid over and including 25 mm thick sand cushion, complete all as specified and directed.

M&L for machine cut kota stone stone slab as in flooring 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for machine cut kota stone slab as in skirting, dado, risers etc, 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 10 mm thick CM 1:4 backing, complete all as specified and directed.

Dismantling loose concrete cover of RCC columns, beams and the like, area not exc 2.0 Sqm each, roughening and cleaning of concrete surfaces with steel wire brushes, washed with water and allowed to dry including dusting of steel reinforcement, providing welded mild steel wire fabric of mesh size 75 x 75 mm and 2 mm nominal dia of wire as reinforcement to concrete surfaces, applying adhesive/admixture over steel mesh and providing ordinary portland cement 53 grade and 2 parts of sand mixed with admixture at the rate as per manufacturer's instructions with a pressure of 2 to 2.5 Kg/Sqcm by guniting machine including necessary padding, steel scaffolding and shuttering for working platform/formwork etc, complete all as specified and directed.

All as per item 79.00 (here-in -before) but area exc 2.0 Sqm each, complete all as specified and directed.

M&L for 15 mm thick rendering on other than fair faces of brick work or stone masonry surfaces in Cm 1:4 using water proofing compound as per manufacturer's instruction's, finishing surfaces even and smooth without using extra cement complete all as specified and directed. ( Note: Water proofing compound shall be measured and paid separately.)

M&L for 10 mm thick rendering on other than fair faces of brick work or stone masonry surfaces in Cm 1:4 finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5 mm thick in CM 1:3 on concrete surfaces of ceiling, finished even and smooth without using extra cement and applying three coat of white wash including preparation of surface complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick/concrete surfaces in CM 1:6 finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and applying two coats of distemper oil emulsion over a coat of primer over 1.5 mm thick Wall care putty as per manufacturer's instructions complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and applying two coats of exterior emulsion paint complete all as specified and directed.

M&L for applying three coats of white wash after preparation of new plastered surfaces of walls, complete all as specified and directed.

M&L for preparing old plastered surface of wall and applying two coat of white wash complete all as specified and directed.

M&L for preparing old plastered surface of ceiling and applying two coat of white wash complete all as specified and directed.

M&L for preparation of new surfaces of walls and applying two coats of distemper oil emulsion over & including a coat of 1.5mm thick wall care putty complete all as specified and directed.

M&L for preparing new previously untreated plastered surfaces of walls and applying two coats of modified exterior acrylic emulsion paint over a coat of primer, complete all as specified and directed.

M & L for preparation of new or previously untreated wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M & L for preparation of old painted surfaces of wood or wood based materials of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint, complete all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M & L for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Supply, fixing, laying & testing 15 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

Supply, fixing, laying & testing 20 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 500 lts capacity (cylindrical vertical with closed top) hoisted and fixed in position, ISI Marked complete all as specified and directed.

S&F 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F in renewal 15 mm bore stop valve/ angle valve, cast copper alloy, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed.

S&F in renewal 15 mm bore bib tap fancy type, cast copper alloy, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed.

S&F in renewals 15mm bore stop valves, fancy type, chromium plated brass with long shank and cup (Concealed type), screwed down, high pressure, both ends screwed to iron pipe or for union, dia of pipe 15 mm, complete all as specified and directed.

S&F gun metal globe or gate valve of size 20 mm dia with iron wheel head screwed both ends and for iron pipe & fixed, complete all as specified and directed.

S & F in renewal 15 mm dia chromium plated brass central hole wash basin mixer (pillar tap) with accessories in wash basins for mixing hot and cold water, screwed down for 15 mm dia GI pipe complete all as specified and directed.

S&F in renewal 15 mm dia CP brass wall mixer for mixing hot and cold water with two CP brass wall flange, screwed down for iron pipe and fixed, complete all as specified.

S&F in renewal shower rose, chromium plated brass, fancy type, 125 mm size with swivel joint, screwed to iron pipe or for union of 15 mm dia, complete all as specified and directed.

S&F in renewal D type towel rail 60 cm long of stainless steel, Chromium Plated, fancy type, 20 mm dia fixed with steel screws complete all as specified and directed.

S&F 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F in renewal of soap dish made of stainless steel, approx size 160x100 mmx 1 mm thick, fixed to walls with plugs & SS screws, complete all as specified and directed.

S&F stainless steel utensil plate rack of size 790 x910 x 250 mm, made of 0.80 mm thick stainless steel sheet and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

S&F in renewal sink without draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality PVC waste pipe and connecting union to pipe overall size 600 mm x 450 mm bowl size 490 mm x 350 mm x 200 mm complete all as specified and directed.

S&F in renewal 10 Ltr vitreous china valveless syphonic action type flushing cistern, low level, coloured with inlet, ball valve, float and handle incl PVC flush pipe of 32 mm dia, fixed to wall, complete all as specified and directed.

S&F in renewal flushing jet CP for pedestal pattern WC including flexible pipe and brass chromium plated nuts, bolts and water pipe of size 1150mm long of appropriate dia complete all as specified and directed.

S&F in renewal vitreous china wash hand basin flat back 550 x 400 mm excluding tap but including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, PVC waste pipe with connector, brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed.

S&F in renewal vitreous china wash down water closet pan, padestal type, white, including recessed bottom PVC seat cover of white colour and mild steel chromium plated hinging device but excluding flushing cistern, flush pipe and fixing bolt and making connections to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc, fixed in renewals, complete all as specified and directed.

S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms), complete all as specified and directed.

S&F PVC connection, 15 mm size with two CP brass nuts, length of connection 450 mm, complete all as specified and directed.

S & F in renewal Harrison rails, stainless steel with fixing brackets, stops, rollers etc.complete all as specified and directed.

S&F in renewals PTMT alloy toilet cabinet with mirror of overall size 350x450 mm and fixed to wall complete all as specified and directed, complete all as specified and directed.

S&F auto close hinges, stainless steel, bright finish or electro galvanised, complete all as specified and directed.

S&F 12 mm thick acrylic shelf assembly, corner type, 300mm size with D bracket and fixed to wall with PVC rawl plug and SS screws complete all as specified and directed.

S&F brass knobs 35-40 mm dia, powder coated, fancy type, fixed with brass screws, complete all as specified and directed.

M&L for providing 40 mm dia and 45 cm length GI medium grade pipe as spout in sunken floor including cutting holes in brick walls/RCC, built in cement mortar and making good the dismantled portion in PCC 1:2:4 type B-1 with using 20 mm graded stone aggregate and finishing the same to match with external surface, complete all as specified and directed.

M&L for 150 mm dia salt glazed stoneware drain pipes, laid in trenches and jointed in cement sand slurry in 1:1, complete all as specified and directed.

M&L PCC 1:4:8, type D-2 using 40 mm graded stone aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of 150 mm dia pipe, after they are laid and tested, complete all as specified and directed.

M&L 600 mm dia Reinforced concrete pipes, class NP3, laid and jointed in trenches complete with collars, complete all as specified and directed.

S&F floor door stopper of brass body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 150 mm, complete all as specified and directed.

S&F 75 mm dia PVC (SWR) floor trap, with CP grating including jointing to waste pipe and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm dia, single socketed, in any length with rubber ring joints and laid in trenches/floor, complete all as specified and directed.

S&F PVC (SWR) pipe 75 mm dia, single socketed, in any length with rubber ring joints and laid in trenches/floor, complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm dia, single socketed, in any length with rubber ring joints and fixed to walls, complete all as specified and directed.

S&F PVC (SWR) pipe 75 mm dia, single socketed, in any length with rubber ring joints and fixed to walls, complete all as specified and directed.

S&F PVC (SWR) 110 mm dia single Junction 'T', equal or unequal, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F PVC (SWR) 75 mm dia single Junction 'T', equal or unequal, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F PVC (SWR) bend 75 mm dia, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) bend 100 mm dia, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall complete all as specified and directed.

Taking down sub main wiring /XLPE cable of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed.

M&L for Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface including providing wooden/PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surfaces, complete all as specified and directed for the following: - One light/ceiling fan/exhaust fan/bell buzzer point controlled by one, one way switch of 5/6 Amps.

All as per item No 142 (here-in-before) but one 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.

All as per item No 142 (here-in-before) but one 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

All as per item No 142 here-in-before) but one light point controlled by two, two way switch of 5/6 Amps.

M&L Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 2.5 Sqmm, with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable FRLS of size 2.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface for one socket outlet 15 amp on independent board including providing wooden/PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surface, complete all as specified and directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, Two way, ISI marked, complete all as specified & directed.

Supply and fixing switch socket combination, 5/6 and 15/16 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

S & F bell push flush type 5/6 Amps 230 volts including cover plate complete all as specified and directed.

Supply and fixing socket outlet, 5/6 Amps, 230 volt, five pin, flush type universal, complete all as specified and directed.

S&F PVC/polycarbonate lamp holder, angular/batten type with back plate, ISI marked complete all as specified & directed.

S&F in renewal of stepped type electronic fan regulator, flush type, 230 volts AC, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 50mm, 3 terminals, complete all as specified & directed.

S&F buzzer, Ding Dong, AC, 230 volts, single pole, ISI marked complete all as specified & directed.

S&F in renewal of wall mounted 18 watt LED Tube light fittings, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed.

S&F in renewal of wall mounted 11 watt LED Tube light fittings, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed.

S&F in renewal of LED building security light fitting, 25 watt, pressure die cast aluminium housing with IP 66 deg of protection, complete with & including 0.55 m long street light bracket made of 32 mm bore GI light grade tubing including necessary clamps, nuts, bolts, washers etc, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole & Neutral, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S & F MCB TPN 63 Amps, 415 volts, four pole, B-curve, rupturing capacity 16KA conforming to IS-8828-1996, IEC-60898, complete, all as specified & directed by Engineer-in- charge.

S & F factory made MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, IP-43-IK09 protection grade, earth bar and Din rail, 415 Volts TPN with 4 ways, Double door, complete all as specified and directed. Note for items of MCB DB - (1) The unit rate includes for cutting the brick/stone walls to accommodate DB to make flush to wall. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 ways, Double door, complete all as specified and directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including 20 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed. NOTE for items of submain wiring:- Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm dia shall be measured as one run length. Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC conduit.

S&F ceiling fans of 1200 mm sweep including all accessories such as down rod, canopy, blade set comprising of three blades, hanging arrangement with rubber block, nuts, bolts, washers, split pins, capacitor etc complete with and including PVC insulated twisted twin core 23/0.0076 copper conductor flexible rubber insulated cable of required length from connector/ceiling rose to fan motor including testing, commissioning and painting with black synthetic enameled paints MES number upto 2.5 cm high, complete all as specified and directed.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade GI tubing for protection of earth wire, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 5 and including dismantling and taking out old earthing complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 5 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire and earth wire upto 7.5 m. Any variation below or above shall be measured and paid for separately under relevant item of this Sch ‘A’.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 200mm with and including PVC insulated three core 23/.0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing MES No with black synthetic enamel paint 2.0 cm high and including making appropriate hole in the wall/ window complete all as specified and directed.

S&F XLPE, insulated, screened, PVC bedded galvanised steel strips or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 Volts grade of size 25 sqmm, 3.5 core laid in trenches, ducts, encased in GI pipe, fixed to pole/wall, laid under road, path, drains, culverts, fixed bare including jointing testing, complete all as specified and directed.

M&L dry clean Sand filling in trenches around underground cables for earth cushion, complete all as specified and directed. Note: - Depth of sand shall be measured after punning.

Supplying and laying pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), laid flat adjoining each other as in protection to UG cables, complete all as specified and directed.

Cutting of road / hardstanding upto a size not exceeding 20 cm in width and not exceeding 60 cm in depth for laying of LT UG cable protection pipe line, making good the disturbed portion so as to match existing finishing or with PCC 1:2:4 type B1 complete all as specified and directed.

M&L in renewal of 40 mm bore Steel water tubing, light grade, galvanised, with all fitting, laid in trenches/fixed to walls/poles etc as protection to cables, with and including necessary MS clamps, nuts botls, washers etc required for fixing, complete all as specified and directed.

triveni sales corporation

K B Enterprises

Ganesh Contruction

M/s Prem Associates

M/S. EAST ENGINEERS