SPECIAL REPAIR TO DRILL OFFICE BUILDING NO T 127 T 182 PROVN OF STORAGE SHED VEHICLE PARKING SHED URINALS ND CERTAIN MINOR WORKS IN DIFFERENT LOCATIONS IN IMA DEHRADUN

Amount

Demolition of brick or stone masonary built in cement mortar including pre cast articles complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area n.exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area exc 1.5 Sqm but n.exc 4.0 Sqm each complete all as specified and directed.

Dismantling of corrugated AC sheet any pattern including AC ridges as in roof covering etc complete all as specified and directed.. Note:- Opening of existing wind tie where required for taking down of sheet is included in the rate quoted against this item.

Dismantling of timber scantling 40 sqcm and over in section in any position complete all as specified and directed.

Dismantling of timber scantling 40 sqcm and under in section in any position complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above) ground level complete all as specified and directed.

Demolition and breaking up sewage pipes (salt glazed ware ) 150 mm dia set in cement mortor complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n' exc. 1.5 m in depth and getting out in any type soil complete all as specified and directed.

Excavation over areas n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

Excavation in post holes each n.exc 0.5 cum and getting out returning, filling in and ramming earth or broken rubble mixed with earth around in layers watering & removing surplus soil to a distance n.exc 50m & making good surface in any type soil complete all as specified and directed..

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified and directed.

Removing surplus excavated soil to a distance n.exc 50 metre & depositing where directed at a level n.exc 1.5 metre above the starting point complete all as specified and directed..

PCC 1:3:6 typeC-2 using 40mm graded crushed stone aggregate as in foundation filling, mass concrete and sub base of floor etc complete all as specified and directed.

PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation filling, mass concrete and sub base of floor etc complete all as specified and directed.

PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in coping, benching, cills, pcc gola, holdfast and the like including weathering, slightly rounded or chamfered angles and throating, including necessary from work etc complete all as specified and directed.

75mm thick PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in plinth protection or similar places, and finishing the surface even and smooth without using extra cement including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with sealing compound grade 'A' including necessary formwork etc complete all as specified and directed

Brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

Brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Damp proof course 40mm thick PCC 1 : 2 : 4 type B0 using 12.5 mm graded stone agg to horizontal and vertical surfaces including necessary form work over and inlcuding a coat of blown bitumen @1.50 kg/ sqm and provided wiith 150 micron polythine film.complete all as specified and directed..

2nd class hard wood (SAL) as in wooden scantling clean swan including dismantling of old scantling complete all as specified and directed.

2nd class, hard wood plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube & edges will be painted to match with printed sheets complete all as specified and directed.

Pressed steel frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strikes plates etc including PCC 1:3:6 type C-0 using 12.5mm graded crushed stone aggregate as in back filling of frame complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick(style) consisting of frame made out of MS tubes for top & bottom rails ms frame shall be covered with heat moulded plain colour PVC "C" channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification & drawing in SSR etc complete all as specified and directed.

Mild steel flat iron work as in wind tiles including fixing with scrue nut and bolt complete all as specified and directed

35mm thick IInd class hard wood glazed and skeleton shuttered open rebated and prepared to receive glass gauge/(with sash bar) edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass or gauged etc size of members of shutters as specified in SSR Part I section 8 clause 8.24(a) complete all as specified and directed.

30mm thick flush shutter, ISI marked, solid core construction, with partical board core and ply wood face panel commercial type on both side as approved complete all as specified and directed.

35mm thick IInd class hard wood factory made, plain framed panelled shutters (any number of panels) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both face, size of rails and stiles as per IS 1003 (part-I) kiln seasoned and chemical pressure treated complete all as specified and directed.

Butt hinges, 100 mm long, medium weight, cold rolled, mild steel and fixed to frame complete all as specified and directed.

200 mm long aluminium anodised barrel tower bolt extruded section complete all as specified and directed.

150 mm long aluminium anodised barrel tower bolt extruded section complete all as specified and directed.

Extruded aluminium alloy handle 150 mm long fabricated type anodised complete all as specified and directed.

300mm long aluminium anodised sliding door bolts, plate type stove enameled black with bright bolts not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolts plate and two on staple plate complete all as specified and directed.

300mm long mild steel sliding door bolts, stove enameled black with bright bolts not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolts plate and two on staple plate complete all as specified and directed.

200mm long mild steel barrel tower bolt stove enamelled black with bright bolt complete all as specified and directed.

150mm long mild steel barrel tower bolt stove enamelled black with bright bolt complete all as specified and directed.

150 mm long mild steel pressed handles, oval type complete all as specified and directed.

300mm mild steel helical door spring with roller plate for door shutter including welding if necessary complete all as specified and directed.

15mm bore medium grade steel water tubing, galvanised (ISI Marked) with and including all fittings (ISI Marked) and jointed, tested and fixed complete to wall and ceiling or laid in floors etc complete all as specified and directed.

20 mm bore medium grade steel water tubing, galvanised (ISI Marked) with and including all fittings (ISI Marked) and jointed, tested and fixed complete to wall and ceiling or laid in floors etc complete all as specified and directed.

Vitreous china wash down water closet pan (pedestal pattern) white including seat cover of plastic, CP jet and pipe etc complete including necessary PVC pipe fittings complete all as specified and directed.

10 ltr capacity PVC low level flushing cistern, top push type with inlet ball valve, PVC handle, brackets including PVC long bend (flush pipe) of 32mm dia, complete all as specified and directed.

PVC connection, 15 mm size with two CP brass nuts, length of connection 450mm, complete all as specified and directed.

PVC (SWR) bends any radius 75 mm bore complete all as specified and directed

PVC (SWR) bends any radius 110 mm bore complete all as specified and directed

PVC (SWR) junction single (single T ) equal or unequal 75 mm bore with access door complete all as specified and directed

PVC (SWR) junction single (single T ) equal or unequal 110 mm bore with access door complete all as specified and directed

PVC (SWR) vent cowl 75 mm bore complete all as specified and directed

110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches with MS clamp etc complete all as specified and directed.

75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches with MS clamp etc complete all as specified and directed.

PTMT grating doom 100 mm dia with hole (minium weight 25 gms) complete all as specified and directed.

Vitreous china, white, wash hand basin, flat back size 550x400mm 'including MS brackets including cutting for and pinning in, including waste pipe & with 32mm (PTMT) waste coupling (half or full threaded) minimum weight 32gm -45gms) and 15mm bore CP pillar tap 25mm dia PVC (LDPE) of pressure 6Kg/cm2, down pipe 75cm long complete all as specified and directed.

32 mm dia PVC waste pipe with PVC socket complete all as specified and directed.

40 mm dia PVC waste pipe with PVC socket complete all as specified and directed.

15mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

PTMT urinal spreader any colour fixing with 15 mm pipe (min weight 50gms) complete all as specified and directed.

Vitreous china urinal bowl white of size 465x355x265 mm including grating and union for discharge pipe complete all as specified and directed.

15mm bore short body fancy type bib tap chromium plated complete all as specified and directed. Make- Jaguar ESSCO cat part No MQT-511 or equivalent of Cera/Hindware

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated (guard & railing 60 cm long) complete all as specified and directed.

Chromium plated angle cock 15mm dia screwed for iron pipe or brass ferrule, complete all as specified and directed. Make - Jaguar ESSCO Cat Part No MQT526 or eqquivalent of Cera/Hindware

500 Litres capacity rotational moulded polyethylene water storage tanks, three layered, ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including 20mm dia GI light grade washout pipe 50mm long with plug and 20mm dia GI light grade over flow pipe 600mm long with fitting complete all as specified and directed

Ball valve 15mm dia high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball min weight 142 gms complete all as specified and directed.

PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm bore outlet fixed complete all as specified and directed.

Gun metal,globe or gate valve with iron wheel head,screwed both end of iron pipes 15 mm bore complete all as specified and directed.

Gun metal,globe or gate valve with iron wheel head,screwed both end of iron pipes 20 mm bore complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

Glazed ceramic coloured tiles of size 300 mm x 200 mm x 7mm thick, as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile with and including 10 mm thick rendering in cement mortar 1:4 finished rough complete all as specified and directed.

Chequered cement tiles 25 cm x 25 cm x 22 mm thick , set and jointed in neat cement slurry in floor with grey cement mixed with colour pigment with and including 20 mm thick screed bed or bedding layer in CM 1:6 complete complete all as specified and directed.

Machine cut kota stone slab flooring 20-25mm thick over and including 20mm thick cement sand screed in CM (1:6) as base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing complete all as specified and directed.

Machine cut Kota stone slab 20-25 mm thick as in riser of steps, skirting, dado and pillars etc laid over and including 10mm backing coat in CM 1:4 on brick or concrete surface base and jointed with grey cement slurry mixed with pigment to match the shade of slab including grinding, rubbing and polishing etc complete all as specified and directed.

Vitrified ceramic tiles dark shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including 15 mm thick screed bed or bedding layer in CM 1:4 complete all as specified and directed.

Rendering 15mm thick plaster on fair faces of brick work or concrete surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed

Rendering 15mm thick plaster on other than fair faces of brick work or concrete surface in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed

Rendering 5mm thick plaster on concrete surfaces in CM 1:3, surface finished even and smooth as in ceiling etc complete all as specified and directed.

10mm thick screed bed in CM 1:4 over concrete surfaces finished even and smooth without using extra cement mixed with water proofing compound @ 3% by weight of cement or as per manfacturer instructions complete all as specified and directed (WPC shall be paid separately)

Supply only integral water proofing compound complete all as specified and directed.

Pre- painted galvalume aluminium Zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and directed

Pre- painted galvalume aluminium Zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding ridges to wall, fixed with self tapping screws etc complete all as specified and directed

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old steel surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

Preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

Preparation of old plastered surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil emulsion distemper on walls complete all as directed.

Preparing surface and applying one coat of 2-3 mm thick Birla wall care putty on new surfaces of wall as per manufacturer instruction complete all as specified and directed.

Preparing new or previously untreated surface of wall and applying two coats of oil bond distemper over a coat of primer complete all as specified and directed.

Preparation of old plastered surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint complete all as directed.

Preparing new or previously untreated surface of wall and applying three coats of white wash complete all as specified and directed.

Preparing new or previously untreated surface of ceilling and applying three coats of white wash complete all as specified and directed.

Preparing new or previously untreated surface of wall and applying two coats of cement based paint over a coat of cement primer complete all as specified and directed.

Liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden plastic cleats complete all as specified and directed.

Use & waste for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter including fair finished surfaces complete all as specified and directed.

Use & waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick for fair finish surface complete all as specified and directed.

Use and waste of formwork to sides and soffits of floors or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports etc. and similar work of fair finished flat surface of concrete complete all as specified and directed.

Use and waste of form work to edges of concrete slabs n exc 20 cm complete all as specified and directed.

Use and waste of formwork to sides of concrete pillar, columns, posts strutts complete all as specified and directed.

RCC M -25 (Design Mix) using 20mm graded crushed stone aggregate as in foundations, including rafts, footing, foundation beams, plinth beams, bases for columns etc, basement slab, under-reamed piles and mass concrete etc complete all as specified and directed.

RCC M -25 (Design Mix) , type B-1using 20mm graded crushed stone aggregate as in beams, cantilever bressummers lintel over 1.5 m span etc complete all as specified and directed.

RCC M -25 (Design Mix) using using 20mm graded crushed stone aggregate as in slab supported on walls beams and columns in floor, roof, landing and in shelves and the like complete all as specified and directed.

RCC M -25 (Design Mix) using using 20mm graded crushed stone aggregate as in column ,pillars, piers,posts and struts complete all as specified and directed.

Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

150 mm bore, salt glazed stone were (SGSW) drain pipe, grade 'A', laid to slope in tranches and jointed in cement mortar 1:1 including necessary testing for ensuring leak proofing complete all as specified and directed.

PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested suitable for 150mm bore of pipe complete all as specified and directed.

Cutting into existing manholes for connecting new drains of 150 mm internal dia of pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

Demolition of existing soakage well and Construction of soakage well of size 3.60 M dia X 6.0M deep, excavation in any type of soil, foundation in PCC 1:3:6 type C-2, walls of honey combed and solid in M-25 (design mix) concrete, including intercepting chamber, screen chamber, brick work in CM 1:4, plaster where shown on drg shall be 12mm thick in CM 1:6, bearing plaster 15mm thick in CM 1:4, RCC cover slab In M-25, filling with brick bats of gauge 80 to 150mm complete all as specified and shown Drg TD-309 sheet 1/4 to 4/4

Mild steel plates (plain or chequered ) channels square cut or notched (ordinary or counter sunk forming holes with rveted bolts or welded attachment confirming to Fe-290 Gde E-165 complete all as specified and directed.

Mild Steel work as in angle/Tee/ hollow/ tubular section as in vertical post, rafter, purlin etc including special shaped washer etc. complete using ERW or induction butt welded tubes firming to I.S 1161 Gde st 240 complete all as specified and directed.

Rolled mild steel work in roof trusses (framed), trussed, purlin crane gantries, rails and fastenings etc including distance pieces plates cleats etc complete all as specified and directed.

Rolled mild steel work in joist, channel, angles or tee section fixed independently without connecting plates etc complete all as specified and directed.

Mild steel flat iron 40 x 3 mm thick as in wind tie including fixing with screws, nut and bolts complete all as specified and directed.

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

Mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing framed work of water tanks and similar work including pintal hinges, stops hand made sliding bolts etc complete all as specified and directed.

Mild steel works as in bands, straps, hold fast, angle cleats and similar small articles etc complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-1 (using 20mm graded agg)finishing the surface fair and even in floor.complete all as specified and directed.

40 mm thick PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in floor finished even and smooth using extra cement complete all as specified and directed.

100 mm thick PCC 1:2:4 type B-2 using 40mm graded crushed stone aggregate as in floor finished even and smooth using extra cement including spike rolling or making impression of expended metals while the concreate is green complete all as specified and directed.

75 mm thick PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in floor finished even and smooth with using extra cement complete all as specified and directed.

Spreading and levelling in layers n exc. 25 cm thick, well ramming including watering as required etc complete all as specified and directed. Note;- Earth obtained from excavation shall be used under this item of work

Hard core of broken stone/boulder of gauge.exc 63mm but n exc100 mm deposited spread and levelled in layer n.exc 15cm thick watered and levelled in layer n.exc 15cm thick watered and rammed to a true surface complete all as specified and directed.

Factory made precast RCC 1; 2 ; 4 type B-1 covers medium duty of suitable thickness ISI marked with load carrying capacity 5 T/Sqm set in cement mortor 1 ; 4 complete all as specified and directed.

Pre-cast RCC 35 mm thick 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in louvers and jallies set in cement motar 1:4 including all mouldings complete all as specified and directed.

Steel window factory made with side hung shutter including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded including cutting holes in wall for inserting holdfast and making good the dismantled portion in cm 1;3 or sement consrete 1;2; 4 as required complete all as specified and directed as per drawing no TD088 sheet 1/17 to 17/17

Steel window factory made with side hung shutter including projecting type hinges with steel handle and steel peg stay complete with out glazing bars dovetailed or welded including cutting holes in wall for inserting holdfast and making good the dismantled portion in cm 1;3 or sement consrete 1;2; 4 as requiredcomplete all as specified and directed as per drawing no TD088 sheet 1/17 to 17/17

Steel ventilator with top hung shutter including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and directed as per drawing no TD088 sheet 1/17 to 17/17

3 mm thick sheet glass, ordinary quality & glazing with oil putty or fixed with wooden beads in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed

600x600mmx4mm thick 'E' board classic factory finish as in false ceiling including supply and fixing 'Tee" grid frame work made of special section of MS galvanized sheet 0.30mm thick, bottom portion painted with cellular nitro painting, consisting angle cleats of size 25mm wide 1.6mm thick with flange fixed to RCC/CGI roofing with dash fastener or wraping the suspending wire around the existing wooden/steel purlin/rafter for suspending grid frame work of size 605mmx605mm suspended with 02 Nos, 1.60mm dia GI wire @ 600mm C/C on main Tee and fixed to T-grid with the help of level clip or as per manufacturer direction. The section consisting of main Tee 36.5 mm x25mmx1.40mm thick, cross runner tee 23.5mm x26.5 mmx1.4 mm and perimeter angle 40mmx 25mmx2.0 mm thick shall be fixed to wall with GI screw of 40mm long @ 450mm C/C along the perimeter of wall all as per manufacturer's instruction and including taking down existing boards complete all as specified and directed.

Taking down carefully existing aluminum/copper surface/concealed point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and removing material from site for offring schedule of credit except fans etc which shall be re-used in work and making good the disturbed surfaces in CM 1:3 of walls, floors, ceiling etc including distempering to match with existing surfaces complete all as specified and directed.

Supply and laying or fixing or passing through pipe XLPE insulated, armoured, heavy duty electric cables 1100 volts grade with stranded aluminum conductor of size16 sqmm 2 core laid in trench/wall/floor/trusses with including taking down existing cable saddle complete all as specified and directed. Make: Finolex/Havells/Polycab/Gloste

Point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLS having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area drawn in and including concealed non metallic rigid PVC conduit 25mm dia or higher with all fitting and fixing accessories and 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes 1.6mm thick, 60mm deep of required size factory made for mounting switch, regulators etc with and including 3mm thick plastic hylam laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches, sockets etc complete for the following:- Make of wire : Finolex, Havells, Polycab, Grandlay. Make of conduit : Finolex/Ess Ess Kay/ICL Note:- (i) The quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using PVC rawl plugs. (ii) Point wiring & earth wire shall be connected to each & every sunken box. (iii) All screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates.

One light/fan point /exhaust fan point controlled by one switch, one way switch 5/6 Amp

One3 pin/ 5 pin multipurpose socket out let 5/6 Amps on the same board with other switch.

One 3 pin/5 pin switch socket outlet, 5 Amps on independent board.

Description all as per item No 136 here in before but point wiring with 2.5 sqmm multistrand copper conductor cable for one 5 pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm PVC insulated multi strand copper conductor cable as continous earth wire.

Switch piano, flush type, single pole one way, 5 Amp complete all as specified and directed. Make:- Anchor/Legrand/Havells/C&S.

Switch piano, flush type, single pole one way,15 Amp complete all as specified and directed. Make:- Anchor/Legrand/Havells/C&S.

Socket outlet multipurpose, 2 in 1 , 5 pin ,5 Amp flush type complete all as specified and directed. Make:- Anchor/Legrand/Havells/C&S.

Socket outlet multipurpose, 2 in 1 , 5 pin ,15 Amp flush type complete all as specified and directed.. Make:- Anchor/Legrand/Havells/C&S.

Ceiling rose, 63.5 mm dia, ISI marked, three terminal of polycarbonate /isolated body complete all as specified and directed. Make:- Anchor/Crab tree/Ess Ess Kay

Lamp holder angle type PVC/ polycarbonate body with cold grip cap suitable for pendent fitting complete all as specified and directed. Make-,Havells/cona /Anchor

Electronic step rotary type fan regulator 100 W 230 Volts AC 50 HZ complete all as specified and directed. Make:- Anchor/Bajaj /Havells/Usha

Sub main wiring with two single core PVC insulated unsheathed FRLS cable 1100 Volt grade, 6.0 Sqmm size with multi stranded copper conductor drawing into and including PVC conduit in surface/concealed as required including one run single core PVC insulated unsheathed 6 Sqmm cable with multi stranded copper conductor colour code as a earth continuity and connected upto DB including taking down old unserviceable submain wiring complete all as directed. Make of wire : Finolex, Plaza, Havells, Polycab NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit.

Sub main wiring with two single core PVC insulated unsheathed FRLS cable 1100 Volt grade, 4.0 Sqmm size with multi stranded copper conductor drawing into and including PVC conduit in surface/concealed as required including one run single core PVC insulated unsheathed 4.0 Sqmm cable with multi stranded copper conductor colour code as a earth continuity and connected upto DB including taking down old unserviceable submain wiring complete all as directed. Make of wire : Finolex, Plaza, Havells, Polycab NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit.

MCB SPN 40 to 63 Amps, 240 volts ,50 HZ, including connection with suitable size copper lugs complete all as specified and directed. Make:- Legrand, cat part no 408618 to408620 or L&T, ABB, Schneider, C&S

Ceiling rose, surface Bakelite 50x25 mm three equal size terminal fixed on anodised 100x 100 mm pressed steel box flush to wall with 3 mm thick Baklite cover complete all as specified and directed. Make:- SSK /cona /LEGRAND

Sheet metal enclosures for DB single door SPN 4 way with 200 Amps rated bus bar 240 volts single shutter (METAL DOOR) type with blanking plates where required and IP 30-ik09 protection complete all as specified and directed. Make:- Indoasian cat part no 811800 Legrand, L&T, ABB, Schneider, C&S

MCB SP 6 to 32 Amps, 240 volts 'C' Curve 10 KA, including connection with suitable size copper lugs complete all as specified and directed. Make:- Legrand, cat part no 408587 to408595 or L&T, ABB, Schneider, C&S

MCB DB, sheet metal enclosures double door SPN 4 way with 200 Amps rated bus bar 240 volts 2 in 1 shutter (METAL DOOR) type and IP 43 degree protection fixed in repair complete all as specified and directed. Make:- Indo asian cat part no - 811805 or equivellent of Legrand, L&T, ABB, Schneider

MCB DB, sheet metal enclosures double door SPN 8 way with 200 Amps rated bus bar 240 volts 2 in 1 shutter (METAL DOOR) type and IP 43 degree protection fixed in repair complete all as specified and directed. Make:- Indo asian cat part no - 811807or equivellent of Legrand, L&T, ABB, Schneider

Wall mounted energy saving 10W LED 230 volts AC, cool white bulk head luminaire with opal diffuser with and including 10 W LED lamp complete and connected the same with using PVC sheathed and insulated three core flexible23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to walls complete all as specified and directed. Make:- Havells cat part nos RUGBYNEONFT 10WLED860SSYMTOPC or equivellent of /Philips/ Ltd/Syska/C&S

Wall mounted LED batten fitting 10W LED 230 volts AC, cool white not less than 600 mm extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver with and including 10W LED tube rod complete and connected the same with using PVC sheathed and insulated three core flexible23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to walls complete all as specified and directed. Make:- Havells cat part nos ENDURALINEARNEOBS10WLED840SPCHW or equivellent of /Philips/ Ltd/Syska/C&S.

Wall mounted LED batten fitting 22W LED 230 volts AC, cool white not less than 1200 x 108 x 62 mm extruded aluminium heat sink provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver with and including 22W LED tube rod complete and connected the same with using PVC sheathed and insulated three core flexible23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to walls complete all as specified and directed. Make:- Havells cat part nos ENDURALINEARNEOBS22WLED830SPCHW or equivellent of /Philips//Syska/C&S.

Wall mounted LED batten fitting 20W LED 230 volts AC, cool white not less than 1135 mm extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver with and including 20W LED tube rod complete and connected the same with using PVC sheathed and insulated three core flexible23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to walls complete all as specified and directed. Make:- Havells cat part nos ENDURALINEARNEOBS20WLED840SPCHW or equivellent of /Philips/Surya Roshni Ltd/Syska/C&S.

LED light fitting , energy saving 10W LED 230 volts AC, cool white bulkhead luminaire with and including 10W LED lamp, complete and connected the same with using PVC sheathed and insulated t three core flexible23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to walls complete all as specified and directed. Make:- Havells cat part nos HEXAFT10WLED857SSYMBOPCor equivellent of /Philips/Surya /Syska/C&S.

Mirror light 14W batten type 2 long including LED Laumpand all fixture arrangement and connection complete all as specified and directed make :- Crompton Greaves Product code LCL-14-CDL or equivelent make of Philips/Siska/GE

25Watt LED cool white, energy saving IP66, environment friendly, long life, LED street light made up of pressure die-cast aluminium housing with high power LEDs as lighting source and lens embedded PC cover having top opening seperate driver compartment suitable for pole dia 43mm (max) including suitable size of bracket bent in shape including 2 Nos clamps, nut, bolts etc and fixing on walls complete including taking down existing light fitting etc complete all as specified and directed. Make:- Havells cat part No ENDURAPEARLSL25WLED 757 SASYTOPCMP or equivellent to Philips/Surya Roshni Ltd/Syska/C&S

Aesthetically designed 42W LED840 S 2 x 2 , cool white flat panel surface /ceiling mounting which provide soft light and glare free symmetricsl illumination to fisture size (595 x 595 x 70 ) mm with and including 42W LED complete and connected the same with using PVC sheathed and insulated t three core flexible23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to walls complete all as specified and directed. Make:- Havells cat part nosPLUTONEO2x2PLR42WLED840Sor equivellent /Philips/Syska/C&S.

Supply and laying or fixing or passing through pipe XLPE insulated, armoured, heavy duty electric cables 1100 volts grade with stranded aluminum conductor of size 10 sqmm 2 core laid in trenches /duct /wall /floor etc complete all as specified and directed. Make: Finolex/Havells/Polycab/Gloster/plaza

Un-reinforced precast concrete cable cover class LV type1 flat size250 mmx 150 mm x40 mm as protection to under ground cable laid dry flat adjjoining each other complete all as specified and directed

Supply and filling sand with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as specified and directed. NOTE: - Punned thickness shall be measurement & paid.

GI pipe light grade ISI marked 40mm bore for cable protection fixed to poles/along wall/floor/under road/across the drain or nallah with calmps, bolts, nuts & washers etc complete all as specified and directed. Make:- Tata/Jindal /Prakash

Taking down ceiling fan of size 1200/1400 mm sweep and exhaust fan 300 mm to 450 mm sweep from the hanging hook/ wall after disconnecting of electric connection at site of fan and rehanging/ refixing the same after Preparation of old painted body and blades of exhaust fan/ceiling fan before cleaning foreign material filling cavities etc and painted with one coat of synthetic enameled paint by spray painting and marking MES No with paint and hanging as directed.

Air ventilation exhaust fan 250 mm sweep plastc body single phase 240 volts, white in colours including fixing arrangemen and making proper opening in wall and making good to wall etc as per exiting finish complete all as specified and directed Make-,Havells model Ventil Air-DX or equivellent Bajaj / Usha/CG

Heavy duty exhaust fan 300 mm sweep with louvers single phase 240 volts, white in colours including necessary connection and replacement of flexible copper cable from ceiling rose and taking down old unservicible fan complete all as specified and directed Make-,Havells model TERBO Force SP or equivellent Bajaj / Usha/CG

Ceiling fan 1200 mm sweep energy saving model AC single phase 240 V , with electronic type regulator and accessories 5 star rated and connecting up including provision of cable form ceiling rose to fan including taking down old ceiling fan and deposite in MES store, complete all as specified and directed. Make- Havels Model No ES-50 Premium or equivalent of Bajaj//Usha

Lamp holder insulated body with back plate fixed on PVC rectengular block for fixing holder with and including 15 watt LED bulb complete all as specified and directed Make-Havells cat part No;-LED ADORE 15W B22 CDL3STAR BALL LAMP or equivellent /cona /Anchor

Earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test point & to main switch board and testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI light grade earth lead protection pipe etc complete all as specified and directed. NOTE: (i) Earth lead wire and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item. (ii) Any joints in earth lead from earth electrode to test point shall not be allowed/permitted. (iii) If the desired earth resistance is not found within permissible limit shall be re done by contractor at no extra cost.

Aggrawal Builders and Furnishers

JAIN BUILDERS

M/s caspur construction company

Sharda Enterprises

M/S P K ARORA