Special repair False Ceilling and wall Panelling with Fire Retardant at Eqpt Room and certain B/R repairs at AFS Mandore Provn of Aluminium Partition at Stn Armory Power House and certain paces at AFS Mandore Provn of Grease Trap and Three teir wash

Demolition of Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets

Dismantling of battens for tiles, shingles etc, of any size including tilting fillets spacing exc 15 cm

M& L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

M&L for 12 mm thick Fibre insulation boards flame retardant type, treated on one face only fixed or laid/ inserted to GI framework with screws fixed in jointless finish with jointing compound and jointing tape as per manufacturer instructions

M&L for 12 mm thick Fibre insulation boards flame retardant type, treated on one face only fixed or laid/ inserted to GI framework with screws fixed in ceiling flat or sloping fixed in jointless finish with jointing compound and jointing tape as per manufacturer instructions

M & L for two coat of fire resisting paint on surfaces of any description wood, steel, iron, concrete, brick, stone, etc., exceeding 10cm in width or girth

Taking down Chowkats or frames exc 1.5sqm but not exc 4 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; cooler stand; 12 mm sq gaurd bar framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M & L Sheet glass ordinory quaility and glazing 5.50 mm thick with oil putty in square pannel exc 0.5 Sqm in Each pane

S&F for Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

Taking down cement or cement lime plaster, any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engineer-in-Charge

M & L 15 mm thick rendering on fair faces of brick walls in CM 1:4 , finished fair & smooth w/o using extra cement.

M & L 15 mm thick rendering on fair faces of brick walls in CM 1:6 , finished fair & smooth w/o using extra cement.

M & L 10 mm thick rendering on fair faces of brick walls in CM 1:3 , finished fair & smooth w/o using extra cement.

M & L for preparation of new plastered surfaces of walls and applying two coat of OBD complete as spd & directed

M & L for preparation of new plastered surfaces of walls applying two coat of cement base paint of approved shade complete as spd & directed

Taking down rolling shutter of any size and removing from site complete all as specified and directed by Engineer-in-Charge.

S&F for Steel rolling shutters, Thickness of laths in 1.25 mm with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type

Ditto, but gear operated type with bevel gear box and crank handle

S&F for Safety lever locks mild steel with 4 levers for rolling shutters

S&F for Ball bearing for rolling shutters

M&L for preparation of new steel & Iron surface of width or grith exceeding 10cm & applying two coats of synthetic enamel paint of 1st quality complete all as spd & directed

Excavating in trenches n exc 1.50 m in width and n exc 1.50 m in depth for foundation,manholes etc as well as n exc 10 sqm on plan area and getting out in soft/ integrated rock all as specified and directed.

Removal of exacavated soft/disintegrated rock to a distance exc 250 and n. exc. 500m m and depositing where as directed at a level of 1.5 m above the starting point complete all as specified and directed.

M & L for PCC 1:4:8 , type D-2, using 40mm graded crushed stone aggregate as in foundation , filling and mass concrete.

M&L for PCC block masonary with solid blocks exc 10 cm in width 1:3:6 Type C1 20 mm graded aggregate and setting in mortar complete .

M&L for pre-cast cement concrete slabs, lintels, cols, piers etc with PCC 1:2:4, type B-1, using 20mm graded stone aggregate complete.

S&F 8 to 10 mm dia mild steel TMT bars , cut to length ,bent to shape required including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete including 15 mm thick screed bed or bedding layer in CM 1:6.

S&F powder coated Aluminium anodised doors frame for doors, window/ventilators with one or more rebates including joining cleats for fixing complete complete all as spd. & dierected Engg. In. Charge.

M&L for preparation of new steel & Iron surface of width or grith exceeding 10cm & applying two coats of synthetic enamel paint of 1st quality over a primer of red oxide complete all as spd & directed.

S & F Powder Coated(thickness or powder coating not less than 50 micron) aluminium anodised doors shutters of aluminium section weighing 0.55 Kg/m including necessary joining cleats glazing clip, ruber neoprane packing, aluminiun handle 02 Nos in shutter, suitable hinge 100 mm long, anodised aluminium snap beading, screw complete all as spd. & dierected

S & F anodised aluminium window and ventilator shutters,sliding type three track without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as suitable handle,locking arrangment complete all as specified.

S&F sheet glass 5.5mm thick ordinary quality and glazing with glazing clips in squares exceeding 0.50 sqm in each pane complete all as specified & directed by Engineer-in-charge .

M&L Galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) (Fe-410 Grade E-250) including distance pieces, cleats etc

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F mild steel work as in wind tie for roof covering complete all as specified and directed by Engineer-in- charge.

Sand filling under floors or in foundations including watering and consolidation

M&L PCC 1:4:8 type D-2 using 40mm graded aggregate as in 75mm thick sub base .

M&L for 25mm thick PCC (1:2:4),typeB-0, using 12.5 mm graded stone aggregate as in floor complete all as spfd & directed.

M&L for pre-cast cement concrete slabs, lintels, cols, piers etc with PCC 1:2:4, type B-1, using 20mm graded stone aggregate complete.

M&L for Glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match & rendering 10 mm thick in CM(1:4) all as specified and complete.

M&L Joint less Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in CM 1:6.

S&F water tubing 15mm bore, medium weight ISI marked galvanized with all fittings & fixed to walls, ceiling or laid in floors complete all as spd & directed.

S&F in repairs for CP single lever center hole basin mixer without popup waste system and complete all as directed by Engr-in-charge

S&F in repairs for CP single lever sink mixer with regular spout w/m , and complete all as directed by Engr-in-charge

S &F pressed steel door frame of size 125x60mm for doors with one or more rebates including nacessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

S & F 2 nd class hardwood 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.

S&F Aluminium alloy, anodised, sliding door bolt 300 mm long with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F Aluminium anodised, barrel tower bolts of extruded section 150 mm long and fixed

S&F 150 mm size Extruded aluminium alloy handles, fabricated type, anodised all as spd & directed.

S&F Mild steel medium weight cold rolled butt hinges 100mm long,all as specified & directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified.

S&F Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket

S&F for PVC (SWR) pipes bore 110 mm single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F PVC (SWR) bends any radius bore 110 mm provided with access door

S&F in repairs PVC (SWR) junction single, (Single T) equal or unequal bore 110 mm provided with access door

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm

S&F vitreous china wash hand basin, white, flat back of size 550x400mm with long screwed shank and fly nuts, flanged end bedded in run lead and other end fixed, including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed by Engr-in-charge.

M&L for Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms)

M&L fo Waste coupling of PTMT for 32 mm (half or full threaded) . (Minimum weight 32mm- 45gms/40mm-60 gms

S&F in repair flexible waste pipe for fixing with 32/38/40mm bore waste coupling of kitchen sink, wash basin etc. all as specified and directed by Engr-in-charge.

S&F ISI marked rotational moulded double layer polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed by Engineer-in-Charge of following capacities :-1000 ltrs

Surface excavation n. exc 30cm deep and averaging 65cm deep and getting out in soft/ integrated rock

M&L for 100mm thick cement concrete type D2, (1:4:8) using 40mm stone aggregate as in sub base.

M&L for Spreading and levelling in layers n exc. 25 cm thick including watering and consolidation.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-35 Grade with grey cement and no pigment

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

Returning filling in trenches incl spreading, levelling, watering, & well ramming in layers not exc 25cm thick complete all as specified and directed, in soil.

M&L PCC 1:2:4 type C-1 (using 20mm graded stone aggregate) as in benching , channel and coping of manholes complete all as specified and directed.

Extra for forming fair finished drains & channels 30cm inner girth in cement concrete using extra cement including forms moulds etc complete all as specified and directed. (Inner girth only measured).

M&L Rendering 15mm thick on brick masonry surfaces or surface other than fair face of brickwork in CM (1:4) mixed with water proofing compound 3% by weight of cement finished even & smooth without using extra cement ( WPC shall be measured & paid separately)

Supplying only Integral waterproofing compound

M&L Mild steel TMT steel reinforcement bars 10mm dia and over cut to length, bent to shape required incl cranking, hooking ends and binding with and including MS wire(annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for precast cover slab in cement concrete 1:2:4 type B1 (20mm graded stone aggregate)l necessary forms moulds etc

M&L for Double Wall Corrugated polythylene(DWC Pipes class SN8) confirming to IS-16098:Part 2:2013 Structured wall plastic piping system for non pressure ,drainage and sewerage of 150 mm internal dia laid , jointed and tested with couplers and all other accessories complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in bed of drain pipes incl packing under and haunching against sides of pipes after they are laid and tested for 150mm dia of pipe.

S & F on site LLDPE CONVENTIONAL Septic tank for 20 users designed to carry sewage and sullage water including vent shaft, connection etc complete all as specified and directed. Make : Sintex / Supreme / Aquatek

Excavation in over areas n exc 1.50 m in depth and getting out in soft/ integrated rock

Loose filling with broken brick aggregates of gauge 80 to 150 mm in soakage pits, soakage wells

M & L for RCC Type B1 1:2:4 (20 mm graded aggregate) in Foundations, including rafts,footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M & L for RCC Type B1 1:2:4 (20 mm graded aggregate in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses

M & L for RCC Type B1 1:2:4 (20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

S & F 5mm dia and over upto and including 10mm dia mild steel TMT , cut to length ,bent to shape required including cranking and binding with and including mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders etc complete.

M & L for form work to sides of concrete foundations, footings, base of columns, sides and soffits of plinth beams, sides of pile caps and similar work for rough finished surface of concrete complete all as specified and directed.

M & L for form work to soffits of suspended slabs such as roof slabs, n. exc. 20cm thick (horizontal or sloping for fair finished concrete surface complete all as specified and directed.

M & L Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter

M & L 15 mm thick rendering on other than fair faces of brick walls in two layers, 1st layer 10mm thick in CM 1:6 and 2nd layer in CM 1:4 with using water proofing compound,and SBR 2% finished fair & smooth w/o using extra cement.( WPC to be measured separately under respective item)

M&L PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in benching , channel and coping of manholes complete all as specified and directed.

Please Enable Macros to View BoQ information