SPECIAL REPAIRS TO BLDG NO T-04 (ISOLATION WARD) AT MH VADODARA UNDER GE (ARMY) BARODA

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness (below or above ground level) complete.

M&L for 75 mm thick PCC 1:3:6 mix type C2 as in plinth protection and paving finishing cone surface even and smooth without using extra cement complete.

M&L for Forming 65mm deep x 10mm thick contraction (dummy joints), filled with sealing compound grade "A" complete.

Demolition of stone slabs and tiles of any description or thickness in floors & wall, laid bedded & pointed in any mortar complete.

Roughning of old unservicable PCC floor surface by picking, chipping and wire brush sweeping clean and washing down with water to remove dust outside to make it suitable for laying floor tile complete.

M&L for 25 mm thick cement concrete in flooring type Bo, 1:2:4 (12.5mm graded aggregate) for laying floor tiles complete.

M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tiles exceeding 0.11sqm and n. exc 0.18 sqm in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15mm thick in cement mortor (1:6) complete.

M&L for vitrified colour ceramic tile 10mm thick (square/rectangular) polished, area of each tiles not. exceeding 0.36 sqm, in floors etc set and jointing in neat cement slurry and pointed in white or colour cement to matching to tile color including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:6 (Tile pattern and decoration shall be as directed) complete.

M&L for vitrified coloured ceramic tile 10mm thick (square/rectangular) polished, area of each tiles not. exceeding 0.36 sqm, in dado/skirting etc set and jointing in neat cement slurry and pointed in white or colour cement to matching to tile color including rendering or bedding layer of mortar 10 mm thick for laying floor finishes with CM 1:4 (Tile pattern and decoration shall be as directed) complete.

M&L for Glazed ceramic coloured walls tiles in vertical surfaces 350x250x7mm / 450x300x7mm thick set and jointing in neat cenment slurry and pointed in white or colour matching to tile color including rendering for screed bed on vertical surface of wall or concrete surfaces in CM 1:4 to receive wall tiles (Tile pattern and decoration shall be as directed) complete.

Dismantling single layer manglore pattern or similar tiles in roofing complete.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated or tile pattern steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ150 as in roof covering/ cladding to wall, fixed with self tapping screws complete.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ150 as in roof covering/cladding ridge or hips, valley gutter to wall, fixed with self tapping screws complete.

Dismantling wooden boarding any description, fixed in any position with nails complete.

Dismantling ceiling and wall boards or insulation board any thickness including cover fillets complete.

M&L for 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh to hanging and size of grid 605x605 mm Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre (Fillets, metal frame work and G.I. wire mesh paid separately) complete.

Taking down cement plaster on brick/concrete surface including racking out joints hacking for key scrubbing down with water etc. complete.

Demolition brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc, complete.

M&L for Brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete.

M&L for Brickwork with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete.

M&L for Rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement) complete.

M&L Rendering in two layer on fair faces of brick work or concrete sur-faces of wall 5 mm thick in CM 1:4 mixed with WPC @ 3% by wt of cement for finished even and smooth without using extra cement over 10 mm thick rendering in cement mortar 1:6 (WPC will be measured and paid separately) complete.

Supply only Internal water proofing compound

M&L for preparing new plastered surfaces of wall and applying two coats of oil bound distamper over and including a coat of 3mm average thick birla / JK or equivalent wall care putty and one coat of chalk whitening primer complete.

M&L for complete removal of old existing treatment completely by scrapping and or rubbing of wall and applying two coats of oil bound distamper over a coat of alkali resistant primer over and including a coat of 3mm average thick birla/ equivalent wall care putty.

M&L for preparing new plastered surfaces of walls, chajja's, roof projection, ceiling below chajja/roof projection (external) etc by dust proof wall sanding machine/building walls grinding cleaning machine and applying two coats of weather coat (exterior paint apex altima) over a coat of alkali resistant primer on external wall all as specified and as directed.

M&L for complete removal of old treatment of plastered surfaces of walls, chajja's, roof projection, ceiling below chajja/roof projection (external) etc by dust proof wall sanding machine/building walls grinding cleaning machine and applying two coats of weather coat (exterior paint apex altima) over a coat of alkali resistant primer on external wall all as specified and as directed.

Taking down chowkats or frame with shutter (without taking off shutter from the frame) Exc 1.5 Sq m but n.exc 4.00 Sq m each

Taking down chowkats or frame with shutter (without taking off shutter from the frame) n.exc 1.5 Sq m

S&F anodised aluminium powder coated frame for doors, windows, ventilators, aluminium grill with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F anodised aluminium powder coated window shutters, side hung/sliding type aluminium sections including necessary joining cleats, sash bars, glazing clips, rubber neoprene packing, handles 01 No in each shutter, 02 Nos hinges per shutter, anodised aluminium snap beading, screws etc. as per manufacturers instruction & trade practee.

M&L for 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, comercial type 1.0mm thick (veneered on both side) with decorative choice laminated type 1 (factory laminated), or surface finish, 6mm thick or external teak wood lipping fixed with nails, color and pattern as approved by EIC/GE.

S&F 35mm thick 2nd class Hard wood Glazed and Skelton shutters, open rebated and prepared to receive glass, gauze etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut ,mitered and moulded beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(a) and fitted to chowkats.

S&F for pressed steel doors frame with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, stainless steel hinges, lock strike plate, etc., complete, as specified and as directed. Note :- Filling of hollow of frame with plain cement concrete anstainless steel hinges of 100 mm size will be measured and paid saperately under respective items.

S&F for pressed steel doors frame with one or more rebates size of frame 105 x 60 mm including necessary fixing lugs, stainless steel hinges, lock strike plate, etc., complete, as specified and as directed. Note :- Filling of hollow of frame with plain cement concrete anstainless steel hinges of 100 mm size will be measured and paid saperately under respective items.

M&L for cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in coping, roof kerb and filling of hollow portion of pressed steel door frame etc. Complete.

M&L for preparing new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete.

S&F 4.00mm thick figured glass, pin head type and glazing with rubber beading or with glazing clips, complete.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, cooler stand and similar work con- forming to Fe.290.Gde-E-165 complete.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete.

S&F solid wood grain printed PVC door frame of size 50mmx47mm made out of 5mm prelam instead of plain colour PVC sheet & edges will be painted to match with printed sheet, reinforced with MS square tube, supplying and fixing in opening as per specification and drawing and matching with door shutter shade. The door frame shall be tied to the wall using 75/100mm long MS screw complete .

S&F 30mm thick factory made both sides choice laminated prelam panel PVC door shutter consisting of frame made out of MS tube of 19 gauges thickness and size 19mm x 19mm for stiles, top and bottom rails, MS frame shall have a coat of steel primer of approved make and manufacture. MS frame shall be covered with 5mm thick heat moulded prelam PVC C channel size 30mm thickness, 70mm width, out of which 50mm should be flat and 20mm shall be tappered in 45 degree < on either sides forming stiles and 5mm, 95mm wide prelam PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide. prelam PVC sheet out of which 75mm shall be flat and 20mm shall be tappered on both sides to form lock rail. Top rail, bottom rail and lock rail shall be provided either sides of the panel 10mm (5mm x2) thick 20mm wide cross PVC sheet shall be provided as gap insert for top rail, and bottom rail paneling of 5mm thick both side prelam PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with 7mm (5mm+2mm) thick 15mm wide. PVC sheet beading on inner side and jointed together with solvant cement adhesive, an additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of C channel using PVC solvant adhesive etc. complete as per Chief Engineer Jodhpur zone TD NO:- CEJZ/TD /03 sheet 1/2 , 2/2

M&L for 100 mm butt hinges, medium weight, cold rolled mild steel, and fixed fixed with pressed steel door frame / pvc door frame with screws complete.

M&L for 100 mm butt hinges stainless steel grade 202, 14 gauge thickness medium weight fixed with pressed steel door frame / pvc door frame with screws complete.

S&F 200mm long Aluminium anodised barrel tower bolt of extruded section and fixed complete.

S&F 150 mm size extruded aluminium alloy handles, febricated type anodised complete.

S&F 125 mm size extruded aluminium alloy handles, febricated type anodised complete.

S&F 300 mm aluminium alloy anodised sliding door bolts, with hasp and staple (bolt type) not less than 12mm dia with and and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium and fixed to wooden door shutters complete.

S&F 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete.

S&F in repairs 20mm dia brass chrom plated tubular towel rail complete.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land complete.

S&F 15mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors all as directed.

Cutting chases for concelled pipe where required and pointing in cement mortor 1:3 etc in brick ball for bore of pipe 15/20 mm complete.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land all as directed.

S&F 20mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors all as directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S&F 110mm bore PVC (SWR) bends any radius all as specified and as directed.

S&F 110mm bore PVC (SWR) bends any radius with oval access door all as specified and as directed.

S&F 75mm bore PVC (SWR) bends any radius all as specified and as directed.

S&F 75mm bore PVC (SWR) bends any radius with oval access doors all as specified and as directed.

S&F 75mm PVC (SWR) floor trap, plain with CP grating including jointing with solvent all as specified and as directed.

S&F 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches with access door all as specified and as directed

S&F 75mm bore PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches with access door all as specified and as directed

S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 110mm bore pipe all as specified and as directed

S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 75mm bore pipe all as specified and as directed

S&F 110mm PVC (SWR) vent cowl all as specified and as directed

S&F 75mm PVC (SWR) vent cowl all as specified and as directed

S&F 100 mm dia CP grating fixed to existing NT/FT including making hole for fixing waste pipe of sink and wash hand basin

S&F 15mm bore pillar taps fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts screwed for iron pipe and fixed

S&F Vitreous China wash basin, white flat baack, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets.

M&L 32mm waste fittings, brass, chromium plated for glazed ware sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S&F 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6Kgf/sq.cm for basins and urinals

S&F 32mm bore brass chromium plated trap 'P' or 'S' pattern for wash basins and urinals with inlet and outlet, screwed for pipe or connections and with one cleaning cap and fixed

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm long.

S&F 15mm bore chromium plated fancy type bib tap long body, screwed down, high pressure for iron pipe or for brass ferrule

S&F stop valves/angle valve 15mm bore cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F 25mm dia bore gun-metal,globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed

S&F in repairs vitreous China squatting pan of Orissa pattern size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including P or S trap etc and provision of lime concrete bedding complete all as specified and as directed.

S&F for PVC low level flushing cistern, white, 10 Ltrs capacity complete with all internal accessorieS&Fixed to wall & making good to wall surfaces incl. taking down existing flushing cistern complete.

S&F stainless steel soap dish

S&F 500 Ltrs Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position including dismantling of old and removing to store all as specified in SSR Part I

S&F Ball brass valves, for 25 mm bore of pipe high pressure, with polythene float and fly- nut complate, screwed for iron pipe or brass ferrule and fixed

S&F CP wall mixer three in one system for mixing hot and cold wather screwed down for iron pipe 15 mm bore and fixed complete all as specified and directed. Make Jaquar Cat part No QQT-7217 or equivelent make.

S&F CP Centre hole Wash Basin mixer three in One 15 mm bore pipe complet all as specified. Make jaquar Cat part No QQT-7167B or equivelent make.

M&L for 100 mm thick PCC 1:4:8 mix type D2 using 40mm graded crushed stone agg as in sub base as in floor.

M&L for Pre polished chequred cement concrete tiles of size 30cm x 30cm x 25mm thick set and jointed and pointed in neat cement slurry in floor with grey cement and pigment over and including 15mm thick screed bed or bedding layer in cement mortor 1:4 complete.

M&L for Reinforced cement concrete (nominal mix) type B1 (using 20mm graded crushed stone agg) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete

M&L MS TMT bars 8-10 mm dia, cut to length bent to shape required including cranking/ Binding/ hooping of coloumns/hooking ends and binding with and including MS wire ( annealed) not less then 0.9 m dia or securing with clips complete

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete

M&L Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete

S&F in 25mm dia stainless steel 202 grade tubular curtain rod as directed

S&F in stainless steel socket fancy type with bracket for 25mm dia stainless steel tubular curtain rod (design of socket shall be approved by GE/AGE at the time of execution) as directed

S&F in repairs factory made 18 (+ 0.7 mm) thick PVC sheet one sided prelaminated sheet cabinate shutters and interior. 18mm (+ 0.7 mm) thick sheet of density 600 kg/m3 bent at 90 degree and finished all edges at all level for making edges, Lipping/bending or 0.5mm thick PVC sheet lipping at ll four edges using bonding tape etc complete all as per directed.

Dismantling ballies, hard or soft wood, type 2, any position, except in posts and struts; including taking out iron straps, bolts and nuts, etc., if any

Dismantling timber scantling under 40 Sqcm in section as in fillet, rails, posts, rafters, purlins etc complete all as specified

S&F in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe-290 (Gde E165) as directed

M&L for 20 mm thick machine cut green marble stone as in floor, steps (in single piece), cooking platform, Jams, Cills of window etc laid over 15 mm thick cement screed and jointed with base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including cement mortar 1 : 4 complete all as specified and as directed.

M&L for door stopper of aluminium body complete all as specified and as directed.

S&F 125mm dia chromium plated shower rose with swivel joints including fixing to GI union complete

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

Dismantling and taking out submain wiring 2/3/4/6 wire of any size and taking out from site all as directed by Engineer-in-Charge.

M&L for concealed point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC insulated and unsheathed FRLS cable 1100 volts grade, conforming IS 694 & color code in conduit system of wiring, drawn in including medium grade PCV conduit not less than 20 mm dia concealed, including cutting chases, finising of slote by means of cement mortor making good to the existing surface of the wall & touching with the existing colour of wall with three coats and making good disturbed surface complete, sunk in pressed steel terminal boxes of required size not less than 1.2mm thick factory made and factory painted with top cover 3 mm thick plastic laminated sheet6 fixed with brass screw and washer with all accessories including single core solid conductor copper 1.5 sqmm size solid PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly drawn in same conduit complete all as specified for One light/fan point controlled by one switch 6 amp one way

All as per item No above but One 3 pin switch socket combination 6 amp on the independent board.

All as per item No above but One 3 pin switch socket combination on same board with other switches.

All as per item No above but but point wiring with 2.5 sqmm single core multi stranded copper conductor PVC insulated & unsheathed FRLS cable 1100 volt grade and 1.5 sqmm PVC insulated and unsheathed cable 1100 volt grade with multi stranded copper conductor for earth wire for 15/16 amp multi purpose socket combination point on independent board.

All as per item No above but One light point controlled by two 2 - way switches, with cables 1.5 sq. mm size ®

S&F MCB DB SPN 12 way factory made IP 42 protection class metal double door with 200 Amp rating bus bar 240/430V for fixing of MCBs/Isolators/RCCBs etc completed. Make: Legrand / Schneider / C&S

S&F MCB DB SPN 4 way factory made IP 42 protection class metal double door with 200 Amp rating bus bar 240/430V for fixing of MCBs/Isolators/RCCBs etc completed. Make: Legrand / Schneider / C&S

S&F MCBs DB TPN 4 way factory made IP 42 protection class metal double door with 200 Amp rating bus bar 240/430V complete. Make: Legrand / Schneider / C&S

S&F MCBs 240/415 Volts 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB Make: Legrand/Schneider/C&S (DB will be measured and paid separately under respective items of sch A):- for MCB SPN 6 to 40 Amps.

All as per item No above but MCB SP 6 to 40 Amps

S&F MCB TPN 4pole 63 Amps 240/415 Volts 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB Make: Legrand/Schneider/L&T (DB will be measured and paid separately under respective items of sch A)

M&L switch piano flush type single pole, one way 6amp .

M&L switch piano flush type single pole, two way 6amp .

M&L switch socket combination 5 pin 6 amp.

M&L switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type.

S&F fan regulator electronic type 100Watt 20V-50Hz as directed by Engr-incharge, Make: Ancho cat No 38660 or equivalent

S&F ceiling rose 65x17mm three terminals .

S&F lamp holder,PVC/Polycarbonate type and back plate suitable for batten fitting along with 09 watt LED Lamp of make : Philips/Bajaj/Wipro

M&L for Concealed Sub main wiring with FRLS two single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 6.0 Sqmm size drawn through and including not less than 25 mm dia PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends fixed to the surface of wall/ceiling including one run of 6.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor. NOTE : Two runs of single core 6.0 sqmm and one run of 6.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length.

M&L for Sub main wiring with two single core PVC insulated and unsheathed FRLS multi stranded copper conductor cable 1100 volt grade IS-694,marked of 4.0 sqmm size drawn through and including 20mm dia PVC conduit medium grade ISI marked and conduit junction boxes,terminal boxes and accessories such as tees, bends, elbows, reducers,bell mouth tube ends fixed to the surface of wall/ ceiling including one run of 4.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor. NOTE : Two runs of single core cable 4.0 sqmm respectively and one run of 4.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length.

Supply, Fixing, Testing and commissioning of 4' LED not less than 1X18W LED Batten with LED tube not less than 18 watt. Similar to Batten cat Part No.REGALBATTEN8UPTO1X22wSSBSWH and LED tube light cat part No.CRYSTAL1213T8DSTL18WLED865SGLASS of Make- Havells or equivalent in Make: Philips/Wipro/CG

M&L earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level,the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and including connected toand including galvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earhing test point and earth dolly all as shown in electrical plate No 5 of MES SSR part I and testing on completion including necessary excavation and earth work in any type of soil,PCC(1:3:6)type C1 chamber,pre-cast RCC slab 50mm thic in cement concrete (1:2:4),type B1,reinforced with welded steel wire fabric or XPM,(weight not less than 4 Kg per Sqm) with cast iron frame,funnel with watering pipe 20mm dia medium grade,wire mesh and lugs,GI protection pipw,15mm dia,medium grade,7.5 mtr long for protection of earth lead upto test point etc all as specified and as directed.

Supply, testing and commissioning a low glare, high effeciency recessed mounted LED downlighter luminaire, Type : LED down light, systen Power consumption not more than 15W,Operating Voltage 170V-270V AC, Similar to Havells model No.EDGEPROSQDLR15WLED857S or its equivalent in Phillips/Wipro.

Supply, Fixing, Testing & Commisioning of 2' 10W Mirror LED Batten with system lumen output of 1000 lumens. System Efficacy should be > 85lm/ W. The Luminaire Should have Cool Daylight Color temp of 6500K & CRI>80.Life 40K burning hrs with 70% lumen maintenace. PF>0.95 Housing of luminaire should made of die cast alumunium & mounting on two PVC square boxes of size not less than 75mm X 75mm complete including connecting fitting with not less tha 0.5 sqmm 3 core flexible stranded copper conductor wire upto ceiling rose complete all as specified & directed. Make- Havells, Model-ENDURALINEARNEOBS1W LED 830SPCWH or equivalent in Wipro/Philips

S&F wall security light LED type 20W The Luminaire Should have Cool Daylight Color temp of 4000K & CRI>70.Life 40K burning hrs with 70% lumen maintenace. PF>0.95 Housing of luminaire should made of die cast alumunium connecting fitting with not less tha 0.5 sqmm 3 core flexible stranded copper conductor wire upto ceiling rose complete with GI bend 1.2 mtr and fixing on wall/pole with clamp, nut & bolt complete all as directed and specified by Engr-In-Charge. Make- Havells, Model-ENDURACITYLITEPLATSL20W LED 757SASYBOPC or equivalent in Phillips/Wipro/CG.

Supply, fixing, testing & commissioning of exhaust fan 300 mm sweep 1400 RPM with minimum airflow/air delivery 1710 Cmh, totally enclosed heavy duty motor, die cast aluminium rotor mounted on double ball bearing, IP-55, polarity-4, 230 Volt AC supply (single phase), rated power input not more that 90watt, with louvers and connecting up including provison of PVC insulated overall PVC sheathed copper conductor cable from ceiling rose to fan. Make : CG/Bajaj/Havells or equivalent. Similar to Crompton Greaves model No EXHD300-4-1 Note: Old UNSV ceiling fans will be deposited to AGE E/M office with RV

Supply, fixing, testing and commissioning Light source LED, Power consumption not more than 36W, Voltage 220-240V AC 50 Hz, Similar to Havells Make VENUSNEOHE2X2PLR36WLED8XXS or its equivalent in CG/Phillips/Wipro.

S&F ceiling fan 1200 mm sweep including fixing of down rod and connection complete with & including provision of flexible three core PVC insulated multi-stranded copper conductor cable of size 0.50 sq mm from ceiling rose/connector to fan complete all as specified and directed. Model- Aura plus of Make : Crompton Greaves or equivalent in Bajaj/Orient/Usha Note: Old UNSV ceiling fans will be deposited to AGE E/M office with RV

M&L for making hole in existing wall of 230mm thickness, suitable for housing of 250/300 mm sweep Exhaust fan complete including grouting of 04 Nos bolt fasteners, PCC work etc including making good disturbed surfaces

Excavation in trenches/post holes in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 meter in depth for laying of cable and for poles/stay and struts not exceeding 10 Sqm on plan and getting out, excavated earth, forming bottom surfaces to required level complete all as specified .

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point.

Returning filling in including spreading leveling watering and well ramming in layers n.exc 25cm thick in soft/loose soil complete all as specified.

Supply and laying in trenches of GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for 25 mm bore of pipe complete all as specified.

Supply and laying in trenches/wall/roof of GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for 20 mm bore of pipe complete all as specified.

S&F 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe.

S&F 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe.

M&L for cutting existing steel tubing for alterations or additions (Each cut measured) and inserting new Tee, bend, elbow etc up to 40 to 50 mm dia

M&L brick masonary valve pit of size 750mm X 750mm X 750mm (internal dimension) complete with MS angle iron frame work (Angle Iron size 40mm X 40mm X 6mm) & 3mm MS sheet top cover openable through hinges including necessary locking arrangement, rendering complete and painting with two coat of black bituminous paint over a one coat red oxide primer

M&L for sand cushoning, to cable with river sand and punning to provide required cover for UG cables all as directed at site.

M&L brick protection cover to electric cable with class 'B' bricks laid dry and flat abutting each other with gap between adjascent not exceeding 10mm.

Supply and laying or fixing or passing through pipe,XLPE insulated armoured heavy duty electric cable with aluminium conducto1100 volts grade cross sectional area 25 sq. mm 4 Core .

M&L for galvanized steel tubing light Grade of 40 mm dia protection of cable fixed to pole/walls or laid in floors, road crossing ducts with all necessary fittings and fittings and fixed with clamps, bolts, nuts and washers etc complete.

RAJENDRASINH B THAKOR