CWE KOTA/ALW-33 OF 2020-21 SPECIAL REPAIR TO BLOCK NO. P-288 and T-289 IN ZORAWAR ENCLAVE AT ITARANA CANTT ALWAR

Amount

B/R ITEMS Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars & precast concrete mosonry etc. and removal all rubbish material complete all as specified directed.

Dismantling of cement concrete tiles in floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement or cement lime plaster any description, on brick or stone walls, etc. including raking out joints, hacking for key & scrubbing down with water, etc. & removing rubbish off the premises, complete all as directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness below or above ground level and removal all rubbish material complete all as directed..

Taking down carefully existing bitumen tarfeit, including plaster of any description over the surfaces of roof, terraces including flashings and junctions of parapets/Curb walls etc. and rmeoving of the rubbish to a distance exc. 500m but n exc. 1.00 km and depositing where directed completeall as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal complete all as specified and directed :-

15mm bore.

20mm bore.

Taking down chowkhats or frames with shutters (without taking off shutters from frame)n exc 1.5 sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from frame) exc 1.5 Sqm but n exc 4 Sqm each complete all as directed.

Taking down shutter of any description exc 1 Sqm but n exc 2 Sqm each complete all as directed.

Dismantling of stone slabs and tiles in flooring or on vertical surfaces etc of any description or thickness laid bedded and pointed in any mortar complete all as specified and directed.

Demolition of reiforcement cement concrete in Roof, Floors (Other than ground floors), beams, staircase, landing, chajjas and similar suspended work, complete all as specified and directed.

Dismantling AC pipes/ PVC pipes 75mm/ 110mm dia,complete all as specified and directed.

Removing steel window shuters by cutting by welding and making good any damage occurred during removal of shutters not exceeding 0.75 sqm each, complete all as specified and directed.

Dismantling water tank of capacity exceeding 250 Ltrs but not exceeding 500 Ltrs and removal from site complete all as specified and directed .

M & L 25 mm thick PCC 1:2:4 type B-1, using 12.5 mm graded stone aggregate as in under floor tiles, finished fair and even complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6 metre mean radius built in cement mortar (1:4), complete, all as specified & directed.

M&L for rendering 5 mm thick in cement mortar 1:3 as in ceiling and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:6 on fair face of brick work as on wall surfaces or on stone masonry surfaces and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on other than fair face of brick masonry surface or on stone masonry surfaces finished even and smooth without using extra cement complete all as specified and directed.Using water proofing compound @ 3% by weight of cement (WPC shall be measured and paid separately).

M & L for use and waste of form work to soffits of supended slabs such as roof slab n. exc 200mm thick, complete all as specified and directed.

Use and waste for formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work exceeding 10cm and n exc 20 cm wide. Where RCC/PCC band in walls, spanning and opening and surfaces finished even and fair complete all as specified and directed

M & L for use and waste of form work to sides and soffits of chajjas for fair finished surfaces, complete all as specified and directed.

Supply only integral liquid water proofing complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

Preparing newly plastered walls surfaces and applying two coats of cement base paint over a coat of water primer complete all as specified and directed.

Prepapration of old plastered decorated surfaces of walls and applying two coats of distemper oil emulsion complete all as specified and directed.

Prepration of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

Prepartion for old decorated surfaces of ceiling and applying two coats of white wash, complete all as specified and directed.

Prepration of old plastered surfaces of wall and applying two coats of white wash, complete all as specified and directed.

M&L for complete removal of washing rubbing down and stopping of distempered and painted surfaces of old plastered surfaces of wall and applying two coats of cement based paint white or tinted on walls including cornices etc. complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and directed.

M & L 450x300x6-7 mm thick glazed ceramic coloured tiles as on vertical surfaces such as skirting or dado and riser to step etc. including 10mm thick rendering in cement mortar 1:4, set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over rendering complete all as specified and directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, including 15mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M&L for vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm as in vertical surfaces such as skirting etc. including 10mm thick rendering in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the dark shade of tile complete all as specified and directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/ rectangular) including plaster in cement mortar 1:6 including necessary cutting of tiles as required size and area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

S &F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with mild steel square tube fixing in opening complete all as per specifications and drawings as applicable to item 08095 given in SSR Part – II (2010).

S & F Factory made solid PVC moulded door shutter, 28 to 30 mm thick (style), with 2, 4 or 6 raised panel design with 2mm thick moulded prelaminated PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, supplying and fixing in frame at site as all as per specifications and drawings as applicable to item 08101 given in SSR Part – II.

M&L 20-25mm thick machine cut Kota stone slab flooring not less than 22" x 22" over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including 20mm thick screed bed in cement mortar 1:6 including rubbing and mirror polishing complete all as specified and directed.

M & L 20-25mm thick machine cut Kota stone slab as in riser of steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick rendering in cement mortar 1:4 including rubbing and mirror polishing including ball nosing of exposed edges complete all as specified and directed.

S&F steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floor etc ) complete all as specified and directed for following bore:- Note : Old serviceable water tubing retrieved from taking down here-in-before shall be used. The quoted rate shall deemed to include new GI fittings (ISI marked). Old fittings shall not be used.

15mm bore.

20mm bore.

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F in repair 15mm bore dia bib tap cast copper alloy long body fancy chromium plated crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repair 15 mm bore angle stop valve of copper alloy, fancy type, chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S & F in repair 15 mm bore dia stop valve of copper alloy, fancy type, chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S & F in repairs, 20mm bore ball valves, high pressure, PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron piped and fixed in positiion complete all as specified and directed.

S & F in repairs 20mm bore Gun Metal globe or gate valve, with iron wheel head, screwed both ends from iron pipe and fixed, complete all as specified and directed.

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors pipe, complete all as specified and directed for the following sizes:-

75mm bore.

110mm bore.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall pipe complete all as specified and directed for the following sizes:-

75mm bore.

110mm bore.

S&F PVC (SWR) bends any radius complete all as directed for the following sizes:-

75mm bore.

110mm bore.

S&F PVC (SWR) 110 mm bore junction single (Single T) equal or unequal with access door complete all as directed.

S&F PVC (SWR) 75 mm bore junction single (Single T) equal or unequal with access door complete all as directed.

S & F 110mm PVC (SWR) WC connectorbent type complete all as specified and directed.

S & F in repairs PVC (SWR) floor trap 75mm dia outlet plain with grating including jointing with solvent cementcomplete all as specified & directed.

S & F 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls with holder bat clamps of GI flat iron 25x3mm complete all as specified and directed.

S & F PVC (SWR) vent cowl for 110 mm bore of pipe complete all as specified and directed.

S&F in repairs vitreous China squatting pan, Orissa pattern, size 580mm x 440mm white with 'P' or 'S' trap front or back inlet and foot rest (any pattern) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc., (excluding flushing cistern and flush pipe etc) and including making good to floor as existing complete all as specified and directed.

S&F PVC low level flushing cistern10 litre capacity with intel ball valve float & handle, syphonic action type including brackets & flush pipe of polythylene of low or high density or PVC 32mm dia for LLFC fixed in repairs all as specified and directed .

S & F in repairs kitchen sink with drainage board made of satinless steel 1 mm thick with plug washer and waste coupling including bedding in cement mortar to dwarf wall or including and fixing cantilever brackets and connecting union pipe over all bowl size 495mm x 420mm x 160 mm / 410mm x 310 mmx 160mm including flush pipe of polyethylene of low or high density or PVC 32mm bore with long screwed shanks and fly nuts complete all as directed.

S & F stainless steel kitchen utencil rack over all size 30"x31"x10" and thickenss of stainless steel plate 0.60mm, fixed to wall with stainless steel screws complete all as specified and directed.

S & F Grating round 100mm size of PTMT (Minimum weight 25 gms), complete all as specified and directed.

S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks galvanised stainless steel wire staples complete all as directed.

S & F 4mm thick sheet glass frosted cut to sizes louvers and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all specified and as directed.

Supply fabrication and fixing powder coated (Thickness of powder coating not less than 50 micron) anodized aluminium windows and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/RM including necessary jointing cleats, glazing clips, rubber neoprene packing, powder coated anodised aluminium snap beading, screws, powder coated anodised aluminium fittings such as peg stays 150mm long (01 No. for each leaf), Butt hinges type B-21 100mm size (02 Nos for each leaf) & handle (01 No for each leaf) etc complete all as specified and directed. (Note :- Glazing shall be measured and paid separately under respective items of Schedule.

M&L for mild steel framed work as in doors or gates angle or others covering door etc to be prepared for handing or sliding with including either hooks and hinges or steel hanging door fittings(exclusive of steel or other covering running rails and guides) and hanging also fastening and fixing complete conforming to FE-290 Gde E-195 all as specified and directed.

M&L 35mm thick factory made 2nd class glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. The shutter shall be fitted to the chowkhats as directed

S & F 35mm thick factory made IInd Class Hard wood (Hollock) plain framed, panelled door shutters two panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of primer complete all as specified and directed.

Preparation old steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint of 1st grade quality complete all as specified and directed.

Preparation of newly wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved shade over one coat of pink primer complete all as specified and directed.

Preparation of old wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved shade complete all as specified and directed.

S & F 100 mm size butt hinges, extruded aluminium alloy with galavanised mild steel hinge pin, ISI marked complete all as specified and directed.

S & F mild steel butt hinges medium weight cold rolled ISI marked of size 100 mm complete all as specified and directed.

S & F 100mm butt hinges, cold rolled mild steel, medium weight and fixed complete all as specified and directed.

S & F 75mm butt hinges, cold rolled mild steel, medium weight and fixed complete all as specified and directed.

S & F mild steel barrel tower bolt, 200 mm long stove enamelled black with bright bolt & fixed complete all as specified and directed.

S & F 150mm long aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

S&F 125mm size aluminium handle, cast type anodised complete all as specified and directed.

S&F 150mm size aluminium handle, cast type anodised complete all as specified and directed.

S&F 300mm long mild steel sliding door bolts with hasp & staples type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, 04 on bolt plate and 02 on staple plate and fix complete all as specified and directed.

S&F aluminium anodised hasp and staple, 100mm size safety type with mild steel hinge pin inncluding to bolt to ginge plate and fixed with screws complete all as specified and directed.

M&L screed bed or bedding layer of mortar over PCC padding , 15 mm thick, in cement mortar 1:4, mixed with water proofing compound 2% by wt of cement on top of chajjas, parapet and over roof slabs finished even and smooth without using extra cement complete all as specified and directed.

M & L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M & L for TMT bars 6mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

S & F for mild steel cupboard shutter with frame, Godrej Pattern, made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangment (brass mortice lock, vertical type, size 65mm, 4 Lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 06 Nos 12mm dia bolt 150mm long grouted in brick wall/concrete including making good the distrubed sufaces as original complete all as directed. Note : The measurment shall be taken of from elevation and not girthwise.

M & L for 7.5cm thick sand stone slabs in sub-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete all as specified and directed.

S & F in repair for powder coated metalic drapery rod of 20 mm inner dia (in lengths as directed) of approved colour with and including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug and steel screws on walls/beam, including PVC curtain rings of matching colour @ 10 cm C/C complete all as specified and directed.

S & F 500 litres, rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top), hoisted and fixed in position and including 20mm float valve complete all as specified and directed. Note : PVC tanks shall be ISI marked and having two layers.

Disconnecting existing tanks, exc. 500 & n exc. 1000 litres setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

M & L for reinforced cement concrete (nominal mix) 1:2:4 type B-1 (using 20 mm graded stone aggregate) as slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for reinforced cement concrete (nominal mix) 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in chajjas and the like complete all as specified and directed.

Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.5 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt (weighing not less than 150 gm/Sqm), with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and as directed. Note :- (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm. (ii) Polymeric membrane shall be taken to a height of 60cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimeny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen. (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate.

M & L for water proofing treatment in sunken floors as described hereunder:- (i) Provide 50mm thick PCC 1:1.5:3 type A-0 using 10/12.5 mm graded stone aggregates laid over slab of sunken floor after applying cement slurry for filling undulations finished fair and even without using extra cement (i) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick cement plaster in mortar 1:4 mixed with water proofing compound @ 3% by weight of cement. (ii) Preaparing plastered surfaces and providing APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd or Hydro Stop manufactured by TIKITAR DANOSA (INDIA) Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, (weight not less than 150 gms/sqm) with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and the joints sealed properly all as per manufacturer’s instructions, and providing a cushion layer of coarse sand of thickness 25mm to protect polymeric membrance complete all as specified and as directed. Note: (i) Polymeric membrane shall be laid in sunken floor and on sides upto finished floor level (ii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iii) Above aspects are deemed to be included in quoted rate. (iv) Supply only water proofing compound shall be measured and paid separately).

S & F in repairs chromium plated brass tubular towel rail 20 mm dia, D type 60 cm long between flanges complete all as directed.

S & F in repair shower rose, chromium plated, 125mm size dixed to 15 mm pipe, complete all as specified and directed.

S & F in repairs vitreous china wash basin, white colour, flat back, size 450 x 300 mm including one No PVC waste pipe 25 mm dia and 75 cm long with 32 mm dia connector, 32mm size waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end, bedded in red lead cement and other fixed complete including cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed.

S & F in repair for 15 mm bore pillar taps cast copper alloy chromium plated fancy type with capstan head screwed down high pressure, with fly nuts, screwed fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and Fixing 32mm dia high density polythylene (HDPE) pipes of pressure rating 6Kg/sq cm in floor or fixed to walls including taking down old pipes complete all as specified and directed.

Supply and fixing 40mm dia high density polythylene (HDPE) pipes of pressure rating 6Kg/sq cm in floor or fixed to walls including taking down old pipes complete all as specified and directed.

M&L 16-18 mm thick granite (of any type) work (table rubbed and polished) in steps jambs pillars, window cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement `1:2) using marble dust with admixture of pigment to match wit complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6 , type C-1 using 20 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 2 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed.

M & L for drilling holes for pipes etc. in cooking plateform stone slab including RCC slab n exc 25mm dia and exc 100mm depth, complete all as specified and directed.

E/M ITEMS Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including teak wood battens/PVC casing caping and making good disturbed surfaces of walls, floors & ceiling etc.including dismentling of fittings to match with existing surfaces, complete all as specified and directed.

M & L for point wiring complete with 1.5 Sqmm single core unsheathed stranded copper conductor cable of 1100 volts grade PVC insulated and unsheathed FRLS cable enclosed in and including PVC casing and capping not less than 20mm width with MS sheet metal sunken switch/terminal box 1.2mm thick and phenolic laminated sheet cover 3.0mm thick and brass screws with cup washers with all necessary wall cutting and making good distrubted surface as directed, including all necessay wall cutting and making good disturbed surface including 1.5 Sq.mm solid copper conductor with green PVC FRLS insulated unsheathed earth continuity conductor to common earth & connecting to earth dolly for the following :-

One light point controlled by one, one way switch

One fan point controlled by one switch and regulator.

One bell/buzzer point controlled by bell push.

One light point controlled by one, two way switch

One 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

One 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per description of serial Item No. 107.00 above but for one 3 pin socket outlet 15/16 Amps with 2.50 sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 volt grade including 2.50 sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 volt grade as continuous earth wire in green colour complete all as specified and directed.

S & F switch piano flush type 5/6 Amps single pole one way 230 volts complete all as specified and directed.

S & F switch piano flush type 5 Amps single pole two way 230 volts complete all as specified and directed.

S & F switch piano flush type 15 Amps single pole one way 230 volts complete all as specified and directed.

S & F, socket outlet 3 pin(with 2 pin outlet also), 5/6 Amp flush type, 240 volts all as specified & directed.

S&F socket outlet two-in-one, 3 pin, 5 Amp and 15 Amp, flush type , 240 Volt complete all as specified & directed.

S&F Bell push flush type 5 Amps siingle pole one way 240 volts complete all as specified and directed by Engineer-in-Charge.

S & F for electric bell/buzzer, AC 230 volts, single pole, ISI marked, complete all as specified and directed.

S & F ceiling rose surface bakelite 65x50mm with two or three terminal complete all as specified and directed.

S&F decorative ultra slim liner LED lighting fixture with extended poly carbonate environmental friendly, energy efficient suitable for 16W to 20W with LED tube of model E-LITE LED pride and connecting up with the fitting from ceiling rose/connector using copper flexible cord of size 1.5sqmm, 3 core of suitable length complete all as specified and directed. Make :- Havelles Cat Part No LHEXBHP71N1W018 or equivalent of Philips/Cromption Greaves/Bajaj/Wipro/GE.

S & F for lamp holder, PVC / polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fixing Adore LED lamps of 9/10 Watt and including taking down old u/s CFL lamp complete all as specified and directed. Make - Cat Part No LHLDERHEML8X010 of make Havells or equivalent model of make Philips/Cromptom/ Greaves/Wipro/Bajaj

Supply & Fixing of stepped type electronic fan regulator flush type and connecting up , ISI marked , 240 Volts complete all as specified and directed.

S & F sheet metal enclosure double door DB SPN 8 way, 240 volts protection class IP-43 made out of CRCA mild steel sheet surface with epoxy powder coated surface confirming to IS-13032, IS 8623, BS-5484 with tinned copper bus bar of 200 Amps capacity all as specified and directed.

S & F sheet metal enclosure single door DB SPN 04 way, 200 volts protection class IP-30 made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted confirming to IS-13032, IS 8623, BS-5484 with tinned copper bus bar of 200 Amps capacity completed all as specified and directed.

S & F sheet metal enclosure single door type suitable for fixing MCB's, SPN with 200 Amps rated bus bar, 2 way, 240 Volts complete all as specified and directed.

S & F MCB SPN 32 Amps, 240 volts, B-curve, rupturing capacity 10KA conforming to IEC-60898, Part-I, complete, all as specified & directed.

S & F MCB SP 6 to 32 Amps, 240 volts, B-curve, rupturing capacity 10KA conforming to IEC-60898, Part-I complete, all as specified & directed.

S&F MCB 63 Amps, 240 Volts, single pole & neutral complete all as specified and directed.

S & F for submain wiring with 2 single core PVC insulated & PVC unsheathed FRLS cable 1100 Volt grade with 06 Sqmm copper multistranded conductor drawn through and including PVC conduit/casing-caping fixed on surface to wall/ ceiling by means of MS screws and saddles including one run of 6 Sqmm single core multistranded copper conductor 1100 volts grade PVC insulated and unsheathed FRLS cable as earth continuity conductor to common earth and connecting to earth dolly and including taking down old u/s sub main wiring complete all as specified and directed. Note: - Two runs of main cable, one run of earth continuity conductor and one run of conduit/casing-caping will be measured and paid as one length only.

S & F second class hardwood rectangular block open recessed of size 30cm x 25cm x 5 cm depth with 3 mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawl plug (4 Nos) complete all as directed.

Supply and fixing LED type street DRACO Series , light luminaire 20 Watt 230 V, 50 Hz and including all necessary fitting accessories and LED complete all as specified and directed. Make:- Cat Part No LTESS20WLED of make C & S or equivalent model of make Crompton/ Greaves/Wipro

Supply / Lying, jointing and testing XLPE insulated armoured heavy duty LT under ground cable with aluminium stranded conductor, 1100 volts grade cross sectional area 16 Sqmm 2 core laid in trenches/ ducts/ through pipes, under floors or roads/along poles etc complete all as specified and directed. Note :- Sand cushioning, Cable protection, GI protection pipe, Clamps, Jointing kits and Excavation & Earth work shall be measured & paid for separately.

Excavation in trenches, n exc 1.5 m wide and n exc 4.50 m in depth or n exc 10 Sqm on plan, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes or for laying underground cable, pipe lines etc. in soft/ loose soil, complete all as specified & directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick,complete, all as specified and directed.

Removal of excavated soil/material to a distance n.exc 50m and depositing where as directed at a level of 1.5 m above the starting point complete all as specified and directed.

M & L for brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) with width equal to the length of brick laid dry and flat abutting each other with gaps between adjacent bricks n exc 10mm over UG cable for protection complete all as directed.

M&L for dry sand and punning for cushioning to under ground cable complete all as specified and directed. Note : For the purpose of payment only punned thickness shall be measured.

Supply and fixing cubical metallic box of size 1.00 mtr x 0.90 mtr x 0.30 mtr depth and made out of 2 mm thick CRCA MS steel sheet, front openable double door type with locking arrangement with and including 3 mm thick plain sheet clear glass of suitable size fixed to facilite meter reading, all internal and external steel surfaces painted with two coats of synthetic enamel paint over a coat of red oxide primer, internal wiring with PVC insulated single core multistranded copper conductor FRLS cable IS - 694 marked of adequate size but not less than 6 Sqmm with proper ferrule and cable gland, box shall be fixed on wall with 'Anchor' type fastner type bolts and nuts (set of 6 bolts of 12 mm dia 200 mm long with nuts and washers ) grounted into the wall properly to hold the box, writing MES/Qtr No for each energy meter with thick white synthetic enamel paint, neoprene rubber gasket shall be provided for proper sealing, including box shall have arrangement for fixing electic energy meter - 04 Nos, MCB DB SPN 4 way - 0 Nos, MCB DB SPN 4 way - 01 No, complete all as directed. Note :- (i) Existing electric meters - 04 Nos will be taking down carefully and refixing the same inside the new meter box carefully including necessary electric connections and sealing the electric meter and MCB DB SPN 4 Way - 01 No and MCB DB SPN 2 Way - 4 Nos shall be measured and paid for separately under relevent items of this BOQ. (ii) Cubical box shall be fix inside (Concelled) the existing wall by necessary cutting/grouting the wall and make good the disturbed surfaces by applying the cement plaster and white wash to match with the adjacent surface of wall.

M&L for earthing complete with galvanized steel earth plate electrode 600x 600 x 6.3 mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 M deep below normal ground level and connected to galvanised iron earth wire 4mm dia by means of bolts, nuts, checknuts and washers of GI or steel all as shown in electrical plate No 3 of SSR Part-I 2009 and connection to main switch board / Test point /panel /equipment all as specified or indicated and testing on completion as directed by the Engineer-in-Charge including necessary excavation & earth work in any type of soil, returning, filling in and removal of surplus soil to a distance n exc 50 M, Charcoal and Salt in alternate layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20mm dia for watering and 15 mm dia 3 M long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25mm x 3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1 40mm thick precast RCC pit cover1:2:4 type B1 shall be provided on CI frame etc complete, all as specified & directed.

M/s ASK Enterprises

SINGH ENTERPRISES

Radha Enterprises

M/s S Amarjit Singh

M/s Laxmi Enterprises

J.J.ENGINEERING