PROVISION OF WEATHER SHELTER/ SHED ALONGWITH MANUAL BARRIACADING SYSTEM AT 02 NOS GATE AT LEKAWADA GANDHINAGAR UNDER GE (I) CG PORBANDAR

Amount

Schedule 'A' B/R

Excavating in post holes (or similar holes) each not exceeding 0.50 Cum and getting out in loose /soft soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layer not exceeding 25cm, watering, and removing surplus soil to a distance not exceeding 50 Metre and making good surface, complete all as specified & directed by Engineer-in-Charge.

Excavating over areas, not exceeding 1.5 Metre deep and getting out in soft loose soil, complete all as specified & directed by Engineer-in-Charge.

Excavating over areas, exceeding 1.5 Metre and not exceeding 3.0 Metre deep and getting out in soft loose soil, complete all as specified & directed by Engineer-in-Charge.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting in any type of soil, complete all as specified & directed by Engineer-in-Charge.

Excavation in trenches in exceeding 1.5 Metre wide and not exceeding 1.5 Metre depth for foundation and getting out in soft and loose soil, complete all as specified & directed by Engineer-in-Charge.

Returning, filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm (soil), complete all as specified & directed by Engineer-in-Charge.

Removing excavation materials not exceeding 50 Metre and deposition where directed at a level not exceeding 1.5 Metre above the starting point (soil), complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Cement concrete 1:2:4 type B-2 using 40mm graded stone aggregate in foundations, filling and mass concrete, complete all as specified & directed by Engineer-in-Charge.

Spreading, levelling, watering and well ramming the earth filling under floor not exceeding 25cm thick in layers, complete all as specified & directed by Engineer-in-Charge. Note :- Soil obtained from excavation shall be used for filling under floors

Material & Labour for providing cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in lintels upto 1.5 Metre clear span, copings, bed plates (block), cills, steps and other bands, parapet and railing upto 60cm height, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for hard core of broken bricks gauge not exceeding 63mm, deposited spreaded and levelled in layer not exceeding 15 cm thick, watered and rammed to a true surface, broken stone or boulder, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Cement concrete in foundations, filling and mass-concrete in PCC 1:4:8 Type D-2 (using 40mm graded stone aggregate), complete all as specified & directed by Engineer-in-Charge.

Material & Labour for 75mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base of floors, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for 75mm thick cement concrete 1:3:6 type C-2, in plinth protection finished even and smooth without using extra cement, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for brick work with fly-ash bricks straight or curved on plan exc 6 m mean radius built in Cement Mortar 1:6, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for brick work with fly-ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified & directed by Engineer-in-Charge.

Material & Labour brick work with fly-ash bricks with sewer bricks straight or curved on plan exc 6 m mean radius for man-holes/septic tank/ soak well etc., built in cement mortar 1:4 in sewer works, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Loose filling with broken bricks of gauge 80 to 150mm in soakage pits, soakage wells, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for 10mm thick rendering in Cement Mortar 1:3 to ceiling surfaces finished even and smooth without using extra cement including preparation of new surface & Three coat of white wash, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for rendering 15mm thick on fair faces or other than fair faces of brick work in Cement Mortar 1:6 finished even & smooth without using extra cement, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Preparation of newly plastered wall surfaces and applying two coats oil bound distemper over a coat of primer, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for rendering 15mm thick on fair faces of brick work in Cement Mortar 1:4 finished even & smooth without using extra cement, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for preparing new plastered or un-plastered surfaces of walls and applying two coats of cement base paint over a coat of primer, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Rough cast plaster as specified .(Rendering coat not less than 10mm thick in Cement Mortar 1:3, while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg size 6 to 12mm mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished eaven), complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid including 15mm thick rendering to receive the stone in cement mortar 1:4 and jointed. and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified & directed by Engineer-in-Charge.

ditto - all as above but kota stone slab (100/150mm x 550mm) and 20-25mm thick in riser of steps, skirting, dados and pillar laid over and including 10mm thick rendering to receive the stone in cement mortar 1:3 and jointed, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for coloured Non-skid ceramic tiles 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc., set and jointed in neat cement slurry pointed in coloured cement to match including 15mm thick screed bed in Cement Mortar 1:6, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for coloured glazed ceramic tiles as on vertical surface of the 450mm x 300mm x 7mm such as in skirting dado etc., set and jointed in neat cement slurry and pointed in coloured cement to match the surface with floor over and including 10mm thick cement rendering in cement mortar 1:4, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, Fe 410-W (Gde-E-250) quality-A, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides as per SSR part I, complete all as specified & directed by Engineer-in-Charge.

Supply and fixing 35mm thick glazed and Skelton shutters to receive glass/gauge of 1st class Hard wood factory made shutter with sash bars for windows/ventilators fixed in position complete all as specified in SSR Part-I Sec 8 clause 8.20(B), complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing steel window with side hung shutter including box type hinges with steel handle with glazing bar, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing steel window with side hung shutter including box type hinges with steel handle without glazing bar, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing steel windows or ventilators, fixed type, with glazing bars, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing figured glass 3mm thick pin head type and glazing with oil putty and securing with glazing pins not exceeding 0.50 Sqm in each pan, complete all as specified & directed by Engineer-in-Charge.

Supply & fixing galvanized mild steel wire cloth 1.18mm average width of aperture and 0.56mm nominal dia of wire fixed with tinned tacks or galvanized wire staple, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing MS work as in grills grating etc., with ends of bars shouldered and riveted framed guard bars, barred iron doors, ladders conforming to FE 410-0 or 310-0, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification, complete all as specified & directed by Engineer-in-Charge.

Supply and fixing 100mm long butt hinges mild steel medium weight cold rolled ISI marked, complete all as specified & directed by Engineer-in-Charge.

Supply and fixing 150mm long extruded aluminum handles fabricated type anodized, ISI marked, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing aluminium anodised barrel tower bolt of extruded section 150mm long, complete all as specified & directed by Engineer-in-Charge.

Supply and fixing mild steel 300mm ordinary rat tail rod pattern springs (ISI marked) including roller and roller plate, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing 300mm long mild steel sliding bolts, stove enamelled black, with bright bolt not less than 12mm dia., complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing Floor door stopper of aluminum allow body and tongue, 150mm overall length, anodised, with hard drawn steel spring, fixed in floor, complete all as specified & directed by Engineer-in-Charge.

Materials and labour for preparation of new wooden surfaces of any description not otherwise described exceeding 10cm width or girth and applying two coats of synthetic enamels paints over a coat of pink primer, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for providing pre-cast cement concrete 1:2:4 type B-1 using 20mm graded aggregate in man hole cover slab set in cement mortar 1:4, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for RCC M-25 (Design Mix) using 20mm graded stone aggregates in foundations, including rafts, footings, foundation beam, plinth beams, bases of columns etc. Basement slabs, under reamed piles and mass concrete, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for RCC M-25 (Design Mix) using 20mm graded stone aggregates in Columns, pillars, piers, posts and struts, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for RCC M-25 (Design Mix) using 20mm graded stone aggregates in beams, cantilevers, lintels etc., complete all as specified & directed by Engineer-in-Charge.

Material & Labour for RCC M-25 (Design mix) using 20mm graded stone aggregates as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Form work to sides of concrete foundations, footings bases of columns and plinth beams and similar works with fair finished surfaces of concrete, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Formwork to sides of pillars, posts, struts, piers columns & stanchions, rough finished surface of concrete, Flat with fair finished surface, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., with fair finished surface, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Formwork to soffits of suspended slabs, such as roof slabs, floor slabs landing and similar work not exceeding 200mm thick (Horizontal & sloping) with fair finished surfaces, complete all as specified & directed by Engineer-in-Charge. (Note- Steel props to be use).

Material & Labour for From work to edges of concrete flats treads breaks in floors, window cill concrete railing, opening in convert valley floor and roof exceeding 5.0 cm but not exceeding 10 cm wide and sides RCC/PCC band in walls with fair finished surface, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia., complete all as specified & directed by Engineer-in-Charge.

Ditto all as above but 5mm dia and over up to and including 8mm dia in stirrups, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for rendering 15mm thick on RCC roof concrete surfaces in Cement Mortar 1 : 4 mixed with WPC @ 3 % by the weight of cement used and finishing even and smooth without using extra cement, complete all as specified & directed by Engineer-in-Charge.

Supply only water proofing compound, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for 40mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate in roof surface, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick reinforced with polyester non-woven fabric (wt not less than 150 gms/sqm) laid on primed surface by torch application including priming, complete all as specified & directed by Engineer-in-Charge.

Materials & Labour for 15mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing 20mm bore medium grade tube galvanised with all fittings and fixed complete to walls & ceiling or laid in floor, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing bib taps long shank 15mm bore dia, fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing 15mm bore CP Angle cock one way chromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing 15mm bore stop valve, cast copper alloy fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing swivel shower for PTMT with shower arm 195mm long with bend of 45 degree 15mm dia (minimum weight 80 gms), complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing grating doom 100mm dia without waste hole of PTMT (Minimum weight 25 gms), complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing rotational moulded polyetlene water storage tanks (Cylindrical vertical with closed top) 500 ltrs cap hoisted and fixed in position, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing 20mm Ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing stainless steel tubular towel rail 20mm dia 600mm long, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing vitreous china wash basin, white, flat back, size 550 x 400mm with pillar tap cast copper alloy with capstan heads, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, waste fitting of PTMT, PVC connection and PVC waste pipe and fixing with new brackets including cutting and pinning in ends of brackets, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing Vitreous china wash down water closet pan (pedestal pattern) white including connection to outgoing pipes and to flushing pipe , fixing of new Plastic water seat closet cover black/ white closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore and connection to WC pan, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing PVC socketed rain water pipe with rubber ring joints 110mm dia fixed to wall, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing PVC socketed rain water pipe with rubber ring joints 75mm dia fixed to wall, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing PVC (SWR) bends any radius bore of 110mm, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing PVC (SWR) bends any radius bore of 75mm, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing PVC (SWR) vent cowl bore 110mm, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing PVC (SWR) vent cowl bore 75mm, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing PVC (SWR) floor trap, plain with grating including jointing with solvent cement dia meter of out pipe 75mm, complete all as specified & directed by Engineer-in-Charge.

Material & Labour cement concrete bed to drain pipe including packing under haunchings of pipe after they are laid and tested in cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) bore of pipe 150mm, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Reinforced concrete pipes, class NP-2, 150mm bore, laid and jointed complete with collars, complete all as specified & directed by Engineer-in-Charge.

Supply and fixing Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300 gms), complete all as specified & directed by Engineer-in-Charge.

Supply and fixing Liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 105 gms), complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing steel work in tubular trusses including columns, special shaped washer etc., complete using ERW or induction butt welded tubes conforming to IS.1161-1998 grade st-240, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment including welding etc., Fe-410-W(gde-E-250) quality B, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing mild steel bolts, purpose made with hexagonal or square head one end and screwed the other, or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut exc 30 cm long diameter of neck in mm exc 20 mm and n.exc 25 mm, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing mild steel screws bolts 5 to 10mm dia (machine made) with hexagonal or square heads at one end and screw the other or screwed both end to be fitted with washers and on hexagonal or square exc 5 cm but n. exc 10 cm long, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing plain angle cleats for securing purlins to trusses or rafters and similar articles conforming to Fe-290 Gde E-165, complete all as specified & directed by Engineer-in-Charge.

Material & Labour for preparation of new or previously untreated surfaces of steel of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of a red oxide zinc primer, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing Installation of century ply HPL 6mm thick exterior grade sheet for cladding plain colour/ shade (Approved by Client) to beam/ column/ slab in circular/ rectangular shape including cutting, notching, bending to shape as required jointing with silicon, rivets with and including fabrication by using aluminium frame of section 34mm X 34mm X 2mm the weight either 1.9 kg to 2.1 Kg (14 gauges) any brand hollow section, rivets application or adhesive, blades, gun, all machinery, tools tackles etc., complete scaffolding material, complete all as specified & directed by Engineer-in-Charge. Note:- Colour/ Pattern of HPL sheet shall be as approved by GE.

Supply & Fixing Installation of century ply HPL 4mm thick, interior grade sheet for ceiling & cladding plain colour/ shade (Approved by Client) to beam/ column/ slab in circular/ rectangular shape including cutting, notching, bending to shape as required jointing with silicon, rivets with and including fabrication by using aluminium frame of section 34mm X 34mm X 2mm the weight either 1.9 kg to 2.1 Kg (14 gauges) any brand hollow section, rivets application or adhesive, blades, gun, all machinery , tools tackles etc., complete scaffolding material, complete all as specified & directed by Engineer-in-Charge. Note:- Colour/ Pattern of HPL sheet shall be as approved by GE.

Schedule 'A' E/M

Material and labour for Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non-metallic rigid PVC heavy duty concealed conduit (minimum 20mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I ISI marked with wall thickness not less than 1.8mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/ recessed in wall or ceiling etc., including 1.5 sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame of required modules for mounting of modular switches, sockets, switch sockets, fan regulators with required modules all as specified etc for the following:-

One light/fan point controlled by one, one way switch

One 3 pin 6 Amps socket outlet on same board

One 3 pin 6 Amps socket outlet on independent board .

Material and labour for Point wiring complete with 2.5 Sqmm single core PVC insulated but unsheathed multistrand copper conductor FRLS cabeI 650/1100 Volts grade conforming to IS-694 drawn through PVC conduit (minimum 20mm dia (external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR Part I) ISI marked with wall thickness not less than 1.8mm heavy duty including conduit accessories concealed pressed steel terminal boxes of size cover white/coloured including 2.5 Sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire for one 3 pin 15 or 16 Amps socket outlet on independent board, including modular type metal flush box with cover plate and frame of required module for mounting of modular switches, sockets, switch sockets with required modules, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing modular switch 1 way, 6 Amps, 1 module (ISI marked), complete all as specified & directed by Engineer-in-Charge. Make : Legrand / Anchor (Roma)/ L&T

Supply & Fixing modular switch 1 way, 16 Amps, 1 module (ISI marked), complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing modular socket, 6 Amps, 2/3 pin combined 2 module (ISI marked), complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing modular socket, 6/16 Amps, 2/3 pin combined 2 module (ISI marked), complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing modular fan regulator, 120 Watt, 2 modules (ISI marked), complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing ceiling rose, surface Bakelite, 65 x 17mm three terminals (ISI Marked), complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing in of wall mounted LED Tube light fitting 1 x 20W LED (6500K), 4 feet, Sleek and seamless profiled extruded aluminium batten with an efficient diffuser to illuminate work, including making connections with 2 core flexible copper wire 0.50 Sqmm from ceiling rose after fixing fitting, complete all as specified & directed by Engineer-in-Charge. Make Wipro - CAT PT No- LL20-281-XXX-65AL1** or equivalent to Bajaj/Havells

Supply & Fixing in of wall mounted LED Tube light fitting 1 x 10W LED (6500K), 2 feet, Sleek and seamless profiled extruded aluminium batten with an efficient diffuser to illuminate work, including making connections with 2 core flexible copper wire 0.50 Sqmm from ceiling rose after fixing fitting, complete all as specified & directed by Engineer-in-Charge. Make Philips -Cat Part No BN 021 LED12S 6500 PSU GR or equivalent to Wipro/GE Lighting

Supply & Fixing LED Wall head light fitting, 20 Watt, E-27 and including connected with 2 core flexible copper wire 0.50 Sqmm from ceiling rose after fixing fitting in position at site, complete all as specified & directed by Engineer-in-Charge. Make: Philips Model No: 31425 /Wipro/CG

Supply & Fixing LED Bulkhead light fitting, with IP-65 protection & IK-08 impact resistance 20 Watt, suitable for wall surface including connected with 2 core flexible copper wire 0.50 Sqmm from ceiling rose after fixing fitting in position at site, complete all as specified & directed by Engineer-in-Charge. Make: Philips Model No: WT140W LED7S NW PSU S1 PC /Wipro/CG

Supply & Fixing flood light IP66 luminaire type 200 W, 5700K with precise flood optics for wide angle light distribution and superior illumination outdoor type, complete all as specified & directed by Engineer-in-Charge. Make Wipro Cat Part No LF30-272-060-57-XX or equivalent make of Philips/CG

Supply and fixing LED 18 Watt Recess mounted slim round/Square down lighter pressure die cast aluminium housing with clear HET diffuser source including necessary connections, complete all as specified & directed by Engineer-in-Charge. Make:- Cat Part No. LD90-231-XXX-65-*** of make Wipro or equivalent model of Bajaj/ Philips /CG

Supply and fixing Recess mounted LED COB 42 Watt down lighter with different beam angle feasibility in die cast extruded aluminium housing with clear diffuser source including necessary connections, complete all as specified & directed by Engineer-in-Charge.Make:- Cat Part No. LD56-501-060-40*** of make Wipro or equivalent model of Bajaj/ Philips /CG

Supply & Fixing sub Main Wiring with two single core PVC insulated unsheathed multi-stranded flexible copper conductor cable of size 2x4 Sqmm and one single core PVC insulated multi-stranded unsheathed flexible copper conductor 4 sqmm size (green colour) cable as Earthing lead connecting to main Earthing dolly drawn in PVC conduit, complete all as specified & directed by Engineer-in-Charge. Note : 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit.

Material and labour for sub main wiring with two single core 2.5 Sqmm PVC (FRLS) insulated multistranded flexible copper conductor cable 660/1100 volts grade down in through including Concealed PVC Conduit with all accessories, PVC insulated 2.5 Sqmm single core single strand copper conductor as continuous earth wire in green colour connected to common earth dolly, complete all as specified & directed by Engineer-in-Charge. Note : 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit.

Material and labour for sub main wiring with two single core 1.5 Sqmm PVC (FRLS) insulated multi-stranded flexible copper conductor cable 660/1100 volts grade down in through including Concealed PVC Conduit with all accessories, PVC insulated 1.5 Sqmm single core single strand copper conductor as continuous earth wire in green colour connected to common earth dolly, complete all as specified & directed by Engineer-in-Charge. Note : 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit.

Supply & Fixing double RJ-11 telephone socket (Jack type) with shutter, One Module, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing Cable outdoor junction box of size 93 x 93 x 87made of polycarbonate sheet, weather proof, IP 66/67 with two pole on /off switch, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing MCB DB 12 way SPN, (Acrylic door), IP 43 “Weather proof” Concealed/ Surface mounted and making good the disturbed surfaces of walls/ceiling/floor etc. complete with all accessories, main switch and connecting the cables with proper, complete all as specified & directed by Engineer-in-Charge. Make: Legrand Cat No 5076 12/ L&T/Schneider or equivalent

Supply & Fixing RCBOs for Earth leakage, Overload & short circuit protection of double pole, up to 300mA & 25A capacity, complete all as specified & directed by Engineer-in-Charge.

Material and labour for MCB SP 240 volt C curve 10 KA, ISI marked as per IS/IEC 60898-1 2002 of 6 to 32 Amps capacity IP 20, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing rigid non-metallic 25mm dia PVC conduit exclusive of boxes (Junction/terminal) but inclusive of all Tee, bends, elbow reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hook etc., complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing junction boxes (1 to 4 way) with cover plates and accessories, complete all as specified & directed by Engineer-in-Charge.

Cutting chases, pinning in, making good to facings where required of brick/stone wall and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth, complete all as specified & directed by Engineer-in-Charge.

Supply and laying of XLPE insulated and PVC armoured heavy duty 1100 volt grade electric LT UG cable with aluminium conductor of size 16 Sqmm 4 Core laid in trenches/along the wall/pole including making good the disturbed surfaces of walls/floor etc., all connections, complete all as specified & directed by Engineer-in-Charge.

Supply & Fixing of GI steel tubing light grade 32mm dia for laying in ground and road crossing along the pole in coping etc for cable protection including necessary fittings, clamps for supports, etc., including making good the disturbed surfaces of walls/floor etc., complete all as specified & directed by Engineer-in-Charge.

Material and labour for cutting existing road/hard standing not exc 45x45 cm in wide & depth getting out excavated material for laying cable/GI tube, returning filling & well ramming watering finish surface 10 cm from top using PCC 1:3:6; including removal of surpluses soil, complete all as specified & directed by Engineer-in-Charge.

Material and labour for LT panel Board cubical Outdoor type compact 415 Volts AC 50 Hz, fabricated of Thermoplastic (Polycarbonate), insulated, shock proof, dust proof, water proof, anti-corrosive and confirming to IP 65/66 complete including copper bus bar 200 Amps 4 strip mounted on porcelain insulated & enclosed in chamber & connection from incoming and outgoing with openable shutter both sides comprising of following :- (a) Copper Bus bar RYB and N of 200 Amp capacity one set, (b) Incoming :- MCCB 63/100 Amp FP 16 KA - 01 No, Outgoing:- (c) MCCB 40 amp FP 16 KA 1 Nos (d) MCB SPN 40 amp 16 KA 3 Nos (e) MCB SPN 32 Amp FP 16 KA 3 Nos, (f) Digital MFM with inbuilt RS-485 port indicating Currents, Voltage, Frequency, (h) LED Indicating lamps for Main Supply R', Y' B' - 01 Set of 3

Material and labour for Earthing complete with Galvanised iron plate electrode 60cm×60cm.× 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less ‘than 1.5 metres below normal ground level, connected to GI earth strip of size 32x6 mm by means of bolts, nuts, check nuts and washers including necessary excavation earth wok, PCC Chamber etc all as shown in electrical plate No 3 of SSR Part-I 2009 and connected to Earthing test point all as specified or indicated including CI Cover, Funnel, GI watering pipe 20mm medium grade, wire mesh and lugs etc. with GI Pipe 25mm bore light grade for protection 7.5 Mtrs long including testing on completion, complete all as specified & directed by Engineer-in-Charge.

Material and labour for Earthing complete with GI earth plate 60cmx60cmx6mm thick electrode and 4mm dia GI wire as Earthing lead. buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level. connected to GI wire earth lead 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 and incl earth work, PCC pit and RCC cover, watering pipe 20mm dia light grade, funnel, wire mesh, protection pipe 15mm dia light grade up to 7.5 mtr length of earth wire, charcoal dust and salt etc and connected to Earthing test point, complete all as specified & directed by Engineer-in-Charge.

Supply and laying 50 /38mm Double Walled Corrugated (DWC) Pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS14930 (Part-II) for protection of UG cables, including snap fit couplers, laid in trenches/ road/ drain or fixed along wall, poles or laid under floor, complete all as specified & directed by Engineer-in-Charge. Make : Rex / Poly/ Gemini

Supplying and laying of CPVC pipes of 32mm dia size SDR 11 & Plain CPVC SDR 11 fittings in trenches & fitting on walls, ceiling or floors, complete all as specified & directed by Engineer-in-Charge.

Cutting the 50mm bore CPVC pipes and reducing the required length before laying for inserting of new such as Tees/Reducers/sluice valve etc., complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Construction of brick masonry valve pit complete including necessary excavation and earth work complete all as specified with internal dimension 150x150x110cm (type 'B') including MS sheet cover 3mm thick welded with hinges on angle iron frame 50x50x6mm with hold fast grouted in 100mm thick PCC (1:2:4) type B-1 coping on top of brick wall including necessary locking arrangement, complete all as specified & directed by Engineer-in-Charge.

Supply & fixing CPVC ball valve of 50mm dia., complete all as specified & directed by Engineer-in-Charge.

Supply & fixing CPVC ball valve of 32mm dia., complete all as specified & directed by Engineer-in-Charge.

divyarsh entrprise (BID ID -3301662)

SNEH TRADERS (BID ID -3302283)