Supply, Installation, Testing and Commissioning of Multi Stage Centrifugal Pump Coupled to 3-phase squirrel cage induction motor along with its allied equipments and Supply/installation of Raising main for LIS Latoo

Amount

Multi Stage Centrifugal Pump Coupled twith 3-phase squirrel cage induction motor : Design, Supply, installation, testing and commissioning of Multistage Horizontal Centrifugal Pump with SS/Bronze Impeller, Cast Iron/S.G Iron casing/WCB, mechanical Seal, bearing lubrication oil, Coupled to energy efficient squirrel cage induction Motor resting on a M.S common base frame properly aligned. The motor shall be suitable for three phase 415 V ± 10%, 50 Hz supply. The job includes parallel combination of two pump sets. Each pump set fitted with Control valves having suitable pressure rating; Cast iron NRV, sluice valves. ERW MS Suction 15m and delivery 5mtr pipe with Long radius 90o bends, foot valves with strainer. clips and clamps, nipples. Delivery pipes of each pump shall be fitted to common pressure header. Provision for priming facility using 25mm heavy duty ball valves 25 mm (ERW) M.S. Pipe etc with each pump and etc. The sizes / quantities of the control valves and suction delivery pipe and other accessories shall be in accordance with the size of the pump and site condition. i) Capacity of Pump = 1 Cusec ii)Total Head = 140 mtr iii) Efficiency = 70% above iv) Driving Motor Rating at 415V ± 10%,50Hz = 100 HP Speed =1450 RPM – 1480 RPM Insulation = F-class

Control panel with one Incomer and two out goings for two pump sets in parallel Operation. (One running and the other standby and vice versa) with Star-Delta Starter for each pump sets. Design, fabrication, assembling, wiring, Installation testing and commissioning fixed type, floor mounted, cubical design motor control centre fabricated out of 2mm/14 SWG CRCA thick sheet duly painted, suitable for indoor use, internally wired complete with Aluminum bus bar covered with PVC heat shrinkable sleeves, colour coded. The panel shall be complete with all protections in-built (Over load/PTC/Line fault / Voltage imbalance / Phase reversal / Under voltage / Over voltage / Over temperature / Open Gate / Excessive Starts per Hr, Single phasing), Main incoming MDO ACB with short circuit release including earth fault and under voltage protection. Bus bar, metering ( incoming and outgoing Voltmeter, Ampere meter, Frequency meter) (3-phase current/3-phase voltage/power factor of running motor, phase indication lamp (RYB with CTs), outgoing MCCB for each pump sets, capacitor Bank for an improved power factor of .95 to 1. The control panel shall be complete with single core copper cable 50 RMT confirming to IS 694 with thimbles from panel to AVR, Automatic Voltage Regulator to Panel and Panel to Motor having option for 3-wire and 6-wire connections, and 3 ½ core aluminum cable of 25 RMT of current rating more than ¬¬235 Ampere from L.T.Pole to control panel. The 3-phase squirrel cage induction Motors ratings are as follows. i) rating=100 HP, ii) Voltage 415± 10%

Maintenance free earthling:- S.I.T.C. of ALLTEC make long life maintenance free electrolytic earthling system with 10 feet vertical k type copper not less then 2”(50.8mm)ID and not less than 0.08”(2.03mm) wall thickness ,which does not require manual addition of water .The system should be corrosion resistant pre-filled with hygroscopic powder and provided with suitable breathing and leaching ports at the ends. Rated for high fault currents bas bar rated for 10KA, fault current bus bar connection type as “Terraweld” to with hold temperature of 7000C.The earthling port shall be designed and supplied with poly plastic port cover non conductive, environment friendly and lockable.

FULLY AUTOMATIC VOLTAGE REGULATOR SITC of fully automatic servo voltage stabilizer duly filled with recommended oil upto full capacity: TYPE = FULLY AUTOMATIC SERVO VOLTAGE REGULATOR RATING = 250 KVA INPUT VOLTAGE RANGE (PHASE TO PHASE) =270-460 V OUTPUT VOLTAGE RANGE (PHASE TO PHASE) =415±1% OUTPUT WAVE FORM = TRUE TO INPUT INPUT FREQUENCY = 45-55 Hz RESPONSE TIME = 10 msec CORRECTION SPEED = 25-65 V/sec CORRECTION METHOD = STOPLESS CORRECTION COOLING = OIL EFFICIENCY = BETTER THAN 98% CONTROL CIRCUIT = FULLY AUTOMATIC IC BASED SOLID STAT, OPERATION = FULLY AUTOMATIC SUITABILITY = SUITABLE FOR 3-PHASE UNBALANCED SUPPLY UNBALANCED LOAD OPERATING TEMPERATURE = -15OC TO 45OC ABOVE AMBIENT ADDITIONAL FEATURES = i)High and low voltage cutoff system. ii)Over load and short circuit protection iii) Single phase prevention system. iv) Phase sequence change protection. v) Earth fault protection. vi) High grade CRGO lamination. vii) Simple rugged construction. viii) 99.9% pure copper. ix) High efficiency. x) Negligible wave form and power factor distortion. xi) Smooth and step less voltage control.

Complete Pump Tool Kit Crimping Tool Hydraulic Type = 1 No Spanner double ended set = 1 set Ring spanner set = 1 set Screw driver = 1 set Socket = 1 set Grease Gun Bucket type = 1 No

SUPPLY AND FIXING OF RAISNG MAIN (The design, material, manufacture, inspection and testing of pipe and valves shall comply with the requirement of latest edition of codes and standard as specified or BS, IS and ASME as applicable)

Supply of MS pipe 6" (150 mm nominal Dia.) medium grade fitted with flanges min 10 mm confirming to IS: 3589-2001, IS-1239, IS4923. Job includes supply of long radius bends required as per site conditions, Specifications: 1. ERW Pipe, Medium Grade Nominal Bore Size = 150 mm (6") Wall Thickness = 6 mm (min)

Supply of 150MM Non Return valve, PN16, Conforming to BS 5153 (EN 12334) / IS 5312 Part 1 & 2, BS 5160/DIN 2401 and latest

Construction of Anchor Block

Construction of PCC Anchor block of size 2’ x 2’ x 4’ using (1:2:4)mix @20 feet c/c. Job includes cost of material, labour, shuttering, tools and tackles etc. The job also includes fixing of 6mm ms strip with suitable anchor bolt to fasten the Pipe on the anchor block. Block size = 2x 2 x 4 = 0.453Cum For 50 blocks = 0.453 x 67 = 22.65 cum

Construction of RCC Anchor block (As per Annexure E) using (1:2:4) mix @ 150mtr-c/c. Job includes cost of materials, including straightening, bending, cutting and placing position, binding all reinforcement, earth excavation, centring shuttering and removal of farm work, carriage charges complete. Total Quantity = 17 blocks

Laying and Fitting charge of Raising Main from pump house to delivery point. Job includes p/f of Carbon steel nut & bolt with washer and 3mm cork sheet gasket of flange size or (any other materials best suited for high pressure leak proof joint) as per site condition.

Water Wealth Infratech India Pvt. Ltd.

ASSOCIATED ENGINEERS

M/s H A ENTERPRISES