Govt. Taluk Headquarters Hospital, Kondotty-Health Grant 2023-24- Setting up of Urban Poly Dental Clinic at Govt. THQH, Kondotty, Malappuram District

Amount

Civil Works

15.23.1 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

15.7.3 Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In lime mortar

15.2.1 Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

15.60 Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

15.52 Dismantling of flushing cistern of all types (C.I. / PVC/ Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead

14.82 Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge

15.19 Dismantling steel work manually / by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per directions of Engineer -in Charge.

6.4.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:4 ( 1 cement : 4 coarse sand)

50.6.2.3 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.7.1 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

50.4.1.1 Providing and laying in position cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) up to floor five level excluding the cost of centering, shuttering, finishing for leveling coarse of floor and roof etc.

11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm

8.2.2.2 Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.4 Extra for fixing marble/ granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete

8.5 Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

12.53 Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.16.2 Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-Charge.Powder coated minimum thickness 50 micron aluminium

21.2.2 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

21.13 Providing and fixing Brass100 mm mortice latch and lock with 6 levers without pair of handles ( best make of approved quality ) for aluminum doors including necessary cutting and making good etc. complete

9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

9.97.3 Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:200x10 mm

50.9.12.1 Providing and fixing Thomson Multi wood board or equivalent make, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately) as per the direction of site Engineer-in-charge

13.61.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

OD198398/2025-2026 Providing and fixing SS hydraulic soft close auto hinges for shelf with necessary fittings including cost and conveyance of all materials and labour charges etc. Complete

9.81.3 Providing and fixing bright finished brass handles with screws etc. complete:75 mm

9.79.1 Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.40 mm

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.48.1 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

50.18.7.3.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10Kgf/ cm2- Internal work- Exposed on wall

50.18.9.16.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6Kgf/cm2 - External work - Exposed on wall

50.18.9.17.1 Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall

50.18.9.19.1 Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.8.3.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2

18.7.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall20 mm nominal dia pipes

18.9.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in-Charge. External work50 mm nominal dia pipes

17.7.2 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brass pillar tap

50.17.1.3 Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in charge.

17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.21.2.1 Providing and fixing uplasticised PVC connection pipe with brass unions: 45 cm length15 mm nominal bore

18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

50.18.9.22.1 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.5 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

OD198399/2025-2026 Providing and fixing 24'x8' acp name board including cost and conveyance of all materials and labour charges

OD198400/2025-2026 Providing and fixing roller blinds made of polyester fabric, measuring 100 to 150 cm in length and 150 cm in width, featuring a heavy-duty 12-gear universal control head, metal brackets for secure installation, a 38 mm diameter aluminum roller tube, and an aluminum heavy bottom rail for stability

100.98.1007 Engaging Beldar

OD198444/2025-2026 Supply & Fixing of LED Acrylic Light Board & Sticker Lettering on ACP Panel at the Entrance area including fittings etc as per the instruction of EIC

Electrification Works

2.2.1 Providing and fixing following rating and breaking capacity MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel. making connections. etc. as required. 100 A, 16KA

90.12.7.27 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 25 sq mm with factory made clamp

OD198445/2025-2026 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (butwithout MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

OD198449/2025-2026 Supplying and fixing 100 amps rating, 240/415 volts, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

2.10.4 Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

9.1.20 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

90.12.7.40 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 10 sq mm with factory made clamp

9.1.32 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

OD198450/2025-2026 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

2.13.2 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.10.1 Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

2.13.1 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.14.2 Supplying and fixing following rating, double pole, (single phase and neutral),240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

2.15.3 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.14.1 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.24.1 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.3 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.27.1 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.4 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

1.3.3 Wiring for light point/ fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required

1.53.1 Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

1.55.3 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

OD198451/2025-2026 Supply, Conveyance, installation , testing and commissioning of 200 mm sweep Light Duty Exhaust fan in plastic body with self opening lowers in the existing opening, fixing necessary anchor bolts / bolt and nuts etc., as required including giving connections with the supplied wire along with the exhaust fan

OD198452/2025-2026 Supply and installation of 1200mm, 20W LED tubelight with all accessories as required. (Make: Crompton/Philips/Wipro)

OD198453/2025-2026 Cable management System for secure and safe routing of power cables and wires

OD198454/2025-2026 Supply, Conveyance, installation, testing and commissioning of 400 mm sweep Wall Mounting fan using mounting brackets supplied along with the fan

OD198455/2025-2026 Supply and Installation of 40W LED high lumen output specialised luminiaries with all accessories for hospital illumination with hanging fittings from roof, to be installed at false ceiling less areas of the laboratory premises.

OD198456/2025-2026 Supply, conveyance, installation, testing and commissioning the following types of light fittings with all accessories directly on wall / in existing false ceiling and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required. 2'x2' LED Square Panel downlight (36W)

4.1.4 Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

5.17 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

2.16 Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

5.2 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal/ coke and salt) as required

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

90.10.3.15 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )32A DP switch with indicator

OD198513/2025-2026 Supply, conveyance, installation, testing and commissioning the following types of light fittings with all accessories directly on wall / in existing false ceiling and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required. 12/15W LED Downlight(Round)

OD198511/2025-2026 Supply Installation Testing and Commissioning of 1.5 TR split type Air conditioner with minimum 3 star rating indoor and outdoor unit fully functional with all accessories including mounting, drainage etc as required with 4KVA Stabilizer (Make: V Guard) including Extended Warranty and AMC for additional 2 years. Make: Bluestar (Model: IA31QCU)

OD198512/2025-2026 Supply and Installation of copper pipe line for the installation of airconditioner units extended with required insulation and protection as required with complete accessories as required

Biomedical

OD195338/2025-2026 MEENAKSHI DENTAL CHAIR MOUNT UNIT Programmable Dental Chair. Unit fitted with. With MM LED (EDI, FARO italy) Operating light having on/Off & intensity control by non- touch sensor Blue Round glass spittoon detachable and autoclavable High and low vacuum motorized CRS Suction System Bee cool II light cure. Modular Trolley System with Hanging Cord. Two airotor points. Supreme micromotor with speed disply 3-way syringe - 2 No. Supreme optic scaler five scaling Tip x ray viewer, SS instrument tray multi-function foot control

OD195339/2025-2026 EURO Dental operator's Stool

OD195340/2025-2026 Confident 1HP compressor with drier and filter: Clean air-150 Monobloc Oil free, Medical Grade Airotor Air Compressor 1Hp Minimum Noise .with drier and filter fitted on MS tank.

OD195341/2025-2026 Confident Sterline B-class Autoclave 23 liter with Thermal printer , Including Water Distiller plant

OD195342/2025-2026 Handpiece:- NSK Airototor SUB2 Airotor Handpiece

OD195343/2025-2026 Supply of NSK Straight Handpiece FX65

OD195344/2025-2026 Supply of NSK Contrangle Handpiece Fx23

OD195345/2025-2026 Supply of PORTABLE DENTAL XRAY Neo, rvg sensor: Output KV (DC)-60kV/65kV/70kV Tube mA-2.3mA Exposure Time-0.01s-1.05 Focal Spot-0.4mm IEC Battery-Li-lon Rechargeable, 2900mAh Cone Length-200mm, Fixed Filtration->1.5mm Al X-Ray Field-60mm Round No.of X-Ray per Charge->200 Advanced Electronics Design Lighter and Smaller Size Powerful Heavy Duty Battery Sensor, Film, PSP Compatible Active Dose Control Very Low Leakage Radiation 0.4mm Focal Spot

OD195375/2025-2026 Supply of Dental implant kit:- make-osstem ,Taper KIT consists of optimal tools and instruments, optimized for taper body implant.- Types of implant placed by use of Taper KIT: TSIII fixture, SSIII fixture, USIII fixture, TSIV fixture, USIV fixture.- Diameter: Ø3.5, 4.0, 4.5, 05.0,

OD195376/2025-2026 Supply of physidipnesor- woodpecker Rotation Speed Range - 300 - 40000rpm Torque Range/Gear 20:1 - 5N.cm- 80Ncm Max Pump Output - 110ml/min Main Unit Dimensions - 23.4mm*L91mm Motor Weight - 140g Power Supply - Ac220v 50/60Hz Device for intermittent operation: 3 min ON,10 min OFF Power supply voltage: 200-240V~ Power supply frequency: 50/60Hz Software version: Implant-V1 Input power: 150VA Fuses: 2×T1.6AL 250V Applied parts: Contra-angle handpiece Maximum Temperature: 41.8 Maximum water volume: 135ml/min Dimension: 276mm*267mm*110mm Environment temperature: +5~40 Relative humidity: 30%~75% Atmosphere pressure:70kPa~106kPa Device case material: PC+ABS Handpiece material: brass Storage: Store in a clean, dry, ventilated, non-corrosive atmosphere with a relative humidity of 10% to 93%, an atmospheric pressure of 70KPa to 106KPa, and a temperature of -20 °C to +55 °C;

Minor Dental Equipments

OD195398/2025-2026 Supply of the Following Equipments: G - Mouth Mirror Handle- 30 nos. G - Probe Single End- 30 nos GDC Extraction Forceps Standard S/12- 1 Set GDC Extraction Forceps Pedo Standard S/7- 1 Set G- Periosteal Elevator- 30 nos G - Artery Forceps Curved- 5 nos G - Gum Scissors Straight- 10 nos GDC Bone Rounger- 2 nos G - B P Handle- 4 nos G - Excavator- 10 nos G Amalgam Condenser- 10 nos G - Plastic Filling Instrument- 10 nos G - Ball Burnisher- 10 nos G - Wax Carver- 10 nos G - Cement Spatula- 10 nos GDC Composite Instruments Gold Titanium S/6- 1 Set G - Matrix Band No.8- 2 nos G - Matrix Retainer No.8- 2 nos G - Mortar- 1 no G - Pestle- 1 no JR - Dappen Dish- 2 nos Koden Cheek Retractor- 5nos. Cotton Bin - 6X6- 2 nos. RK - Steel Tray 12*10- 10nos. RK - Kidney Tray Medium- 10nos. G- Cheatle Forceps- 5 nos. Glass Slab- 5 nos. Mani Diamond Bur SF11- 50 nos. GDC Gracy Curette- 6 nos. G - Tweezer- 25 nos. Elko BP Apparatus Mercury Regular- 2 Nos. G - Bone File- 4 nos. RK Imp Tray Brass U1- 50 nos. Dr. Morepen- Stethoscope Stainless Steel (MS-SS)- 2 nos. Dr.Morepen Gluco One Strip(BG03 25)- 2 nos. Perfecxa Pulse Oximeter- 2 nos. Koden Universal Plier- 2 nos. Koden Adams Plier- 2 nos. Koden Hard Wire Cutter- 2 nos. Dpi - Impression Paste- 6 Pack Gc Fuji 1 Large- 2 nos. Gc Fuji 9 Extra A2- 2 Pack Prevest Zinc F+- 2 Pack Dpi Alloy Fine Grain- 1no Suture Needle - Sabre - 19- 10nos Life Line Surgical Thread - Suture- 5 nos Suction Tip Imported- 10 nos Stone Bur Cone - Pink Large- 10 nos Oro Prophy Cup- 5 nos. Ramraju Plaster of Paris 1Kg- 5 nos Konark SS Orthowire 20- 40nos Gdp - Arch Bar- 10nos Mani Reamer 21MM 15-40 ASSRTD- 10 nos Dpi - Heat Cure Universal Pack Clear- 5nos Dpi - RR Cold Cure universal Pack Pink- 5nos Mani Broaches Assorted- 10nos Dpi - Cold Mold Seal 110Ml- 10nos GDC Crayers Elevator Set (L/R)- 2nos Dental Apexo Elevator - 2 nos GDC Warwick James Set Of 3- 2set GDC Coupland Elevator No. 1- 5 nos GDC Cross Bar Elevator Set- 3 nos Being Contrangle HP- 2 nos Glass Bead Sterilizer - Digital- 1 no. Endo Box Aluminium 60 Holes- 2 nos. Neelkanth-Microtorch- 1 no. Gas Refill Clipper- 1 no. Endo Irrigation Needle 30ga Side Vented- 5 nos. Metapex- 4 nos. Pola Office Kit - SDI- 1 no. Aslate Impr Compound (Asian)- 1nos. Zhermack Tropicalgin Normal Set- 10 nos. Dpi - Green(Pinnacle) Stick- 5 nos. Articulating Paper Deepasree- 5 nos. Vita Shade Guide 3D Master- 1 no. API Crown Remover Automatic- 1 set Koden Face Bow- 1 no. Voco Profluorid Varnish Single- 1 no. Prevest PF Seal 2*2 gm- 1 no. Prevest Orafil G 40 gm- 7 nos. Formoa Cresol-Lp- 1 no. Lidayn Spray- 3 nos. D-Tech Etching- 5 nos. Woodpecker Light Cure Unit LED-D- 1 no. Koden Band Pusher- 1 no. Koden MBT Gauge- 1 no. Koden Anterior Band Remover- 1 no. Koden Anterior Bracket Remover- 1 no. Koden De La Rosa Plier- 1 no. Koden Distal End Cutter- 1 no. Koden Pin & Ligature Cutter- 1 no. Dental RC Solve- 1 no. Prevest Sodium Hypochloride 3%- 1 no. Prevest Pulp X 2*3gm - 1 pkts Koden Basic Brackets-MBT-022- MINI-5X5- 6 kit Koden Molar tubes MBT 018 USLS PK BND- 1 no. Dentsply GP-4-1540- 10 pack Koden Elastic Separators- 1 no. Koden Universal Plier- 1 no. needle burner- 1 no. Ultra Sonic Model UDS N3- 1no Woodpecker Apex Locator - Woodpex V- 1 no.

EXCLUSIVE OF GST

Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2:Rate should be inclusive of Insurance,Transportation, delivery and installation cost for all items

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR/PWD specification and direction of Engineer at site.

5.CEMENT: Make use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

6. SOLID BLOCK MASONRY: Min. average compressive strength as per IS shall be 40-50kg/cm2 and has to be assessed by testing at Govt. lab. ( Variation in rate due to change in size of block and level of floor as per DSR/PRICE has to be considered)

7.ELECTRICAL: Note: Rate should be inclusive of preparation of schematic diagram and getting approval from KSEB/Electrical Inspectorate. Statutory fees paid to KSEB/EI shall be paid by us separately.

Make of Electrical equipments/materials

All electrical materials/equipments shall be of best branded items with ISI, strictly as per schedule specification

Panel Boards: CPRI certified reputed manufacturers make

MCB/ELCB/DB - L&T/LEGRAND/SCHNEIRDER or equivalent

Cables & wires - Finolex/KEI/POLYCAB/RPG/V-GUARD

Switches/Sockets/Regulators - SCHEIDER/ABB/HAVELS/LEGRAND or equivalent

Cable Glands & Sockets - REPUTED MAKE , Cosmos

Indicating Lamps - TEKINIC/RISHUB/STC, L&T, Schneider or equivalent

Ceiling/Exhaust fan: Havells, Orient, Usha, Crompton Greaves, Bajaj

8.DELUXE MULTI SURFACE PAINT SYSTEM: Make: JOTUN, Asian, Berger, Nerolas or eq. in the order of pref.

9.VITRIFIED FLOOR TILES/ CERAMIC GLAZED WALL TILES: Make: Khajaria, Jhonson, RAK, NITCO, Cera or Eq. in the order of preference and prior sample approval from KEL, Client

10.ALUMINIUM WORK: Make: INDAL, JINDAL in the order of preference and prior sample approval from KEL, Client

11.Rigid PVCPipes/Casing & Capping - A-ONE/REPUTED MAKE with ISI , Precession, Balco, GEO

12. ACRYLIC SMOOTH EXTERIOR PAINT/ SYNTHETIC ENAMEL PAINT/WHITE CEMENT BASED PUTTY/ CEMENT PRIMER: Make: Asian, Berger, Nerolas or eq. in the order of pref.

meconconstructions (BID ID -2446741)

K HARINARAYANAN (BID ID -2446270)