Job No.2710 E.E. HSVP Divn. Snp 2019-20

Amount

Supply & Erection of Horizontal spindle split casing type pumping sets of following duties directly coupled to AC squirrel cage induction type motor with accessories complete in all respect with priming arrangement with complete base frame. Make – Kirlosker, Crompton i) 2920 LPM 45mtr head with squirrel cage induction motor 1440 RPM, 3 phase 50 Hz of four star rating (H.P.)

ii) 1710 LPM 45mtr head with squirrel cage induction motor 1440 RPM, 3 phase 30 Hz of four star rating (H.P.)

iii) Vacuum pump motor set 2 HP for releasing air pressure in distribution pipe

Supply and fixing following CI D/F pipe and specials / sluice valves / Non return valves / bell mouth / Reflex valves including cost of jointing, refilling including making adequate support of masonry / concrete steel for delivery and suction pipe from bell mouth in the collecting tank upto the rising main laid by the department as per plan shown from the foundation wall of the pump chamber for all the Raw Water and Clear Water Pumping sets at Water Works as per specification given in Schedule No. II for Detail of pipe and specials i) CI D/F bends, reducers, tees etc. CI/D/F pipes excluding jointing material

i) 100mm i/d

ii) 150mm i/d

iii) 200mm i/d

iv) 250mm i/d

v) 300mm i/d

Providing and fixing cast iron double flanged sluice valve PN -1.6 marked with IS: 14846 including nuts and bolts marked with IS:1363, rubber sheet marked with IS:638 etc. carriage loading, unloading, stacking, handing, re – handing etc. complete in all respect to the satisfaction of Engineer – in-charge (Make AARKO, VENUS, LEADER, SI, PANJA UPADHAY) i) 100mm i/d

i) 150mm i/d

iii) 200mm i/d

Providing & fixing CAST IRON DOUBLE FLANGED swing check type reflux (Non return) values PN -1.6 MARKED WITH IS:5312 including nuts & bolts marked with IS:1363, rubber sheet marked with IS:638 etc. carriage, loading, unloading, stacking handling, re-handling etc. complete in all respect to the satisfaction of Engineer-in-charge (Makes AARKO, VENUS, LEADER, BIR, PANJA, UPADHAY) 100mm i/d

Supply, erection, testing and commissioning wall mounted fully automatic electric panel board, fabricated from 16 SWG, CRCA sheet duly souted with suitable angle iron frame work and completely powder coated of approx.. size 1200 x 900mm and 400mm deep having following items- Make L & T, Siemens. Main Switch 600 Amp, 1 No. ( L&T Snider, BCH, EATON) Volt Meter 200x200 mm range 0 to 500 volt, 1 No. ( L &T Digital Type ) Snider, BCH, EATON Amp meter 200 x 200mm range 0 to 500 volt, 1 No. ( L &T Digital Type ) Snider, BCH, EATON VSS & ASS 2 Nos. each of approved make SPP 2 No. of approved make / Minilac Motor starter, star delta 1 No. for 2920 LPM & 46m (150 ft) head motor & 1 No. Snider BCH EATON Capacitor plus bus bar as per site requirement. Indicating Lamp – One set

Supply and erection of CT / PT Meter

Supply and erection of underground cable 1 metre below ground level covered with sand and bricks including necessary connections, digging and refilling of trenches:- ( HSR Item No. 31.25) xliii) 50 sqmm 4 core cable

Supply and erection of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe (HSR Item No. 31.40) v) Cable size 10 sqmm (7/1.35 mm)

Earthing with GI earth pipe 4.5m long and 40mm dia with masonry enclosure on the top etc. as required (HSR Item No. 31.22)

Earthing with G.I. earth plate 600mm x 600mm x 6mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (But without charcloal or coke and salt ) complete as required. (HSR Item No. 31.22)

Providing & laying earth connections from earth electrode with 4.00mm dia GI wire in 15mm dia GI pipe from earth electrode ad required. (HSR Item No. 31.22)

Exhaust fans 18” i/d (450mm i/d) complete with suitable G.I. sheet of approved make

GROVER APPLIANCES