Construction of Kitchen Shed Retaining Wall and removal of debris for Govt High School Hellan Education Block Bagsaid District Mandi HP

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth in all lead & lifts, as directed by Engineer-in-charge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil as directed, within in all lead & lifts. (a) All kinds of soil.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of material in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 Cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) including carriage of material in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size) including carriage of material in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (1 Cement : 5 coarse sand) : 10 graded stone aggregate 40 mm nominal size) including carriage of material in all leads and lifts.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand) : 10 graded stone aggregate 40 mm nominal size) in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to all level, excluding the cost of centering, shuttering and finishing:. including carriage of material in all leads and lifts

Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc

Stone soling properly handpacked filling interstices with spalls and consolidating with hand ramming to the required level including spreading watering and ramming complete as per HP PWD specification. 100mm spread thickness (finished work including material and labour) including carriage of material in all leads and lifts

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to all level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size). including carriage of material in all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form for : including carriage of material in all leads and lifts.

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Edges of slabs and breaks in floors and walls Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and including binding wire all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more including carriage of material in all leads and lifts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of material in all leads and lifts

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of material in all leads and lifts.

Providing sal wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) including carriage of material in all leads and lifts.

Providing and fixing 35 mm thick kiln Seasoned and Chemicallay treated hullock wood panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in- charge.(Note:- Butt hinges and necessary screws shall be paid separately) including carriage of material in all leads and lifts.

Providing and fixing 35 mm thick Kiln seasoned and chemically treated hollock wood wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws including carriage of material in all leads and lifts.

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete including carriage of material in all leads and lifts.

250 mmx10 mm

150 mmx10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete including carriage of material in all leads and lifts.

125 mm size

100 mm size

Providing and fixing IS marked Mild steel door bolts with nuts and screws etc. complete including carriage of material in all leads and lifts. (a) 300 x 16 mm

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. including carriage of material in all leads and lifts. (a) Fixed to steel windows by welding.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Cement concrete flooring 40 mm thick aggregate 1:2:4 (1 cement : 2 coarse sand : 4 (20 mm nominal size stone) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete including carriage of material in all leads and lifts.

Cement plaster skirting 18 mm thick up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. including carriage of material in all leads and lifts.

Providing and fixing 40 mm wide and 4 mm thick glass strips in joint of cement concrete flooring including carriage of material in all leads and lifts.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet oofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 icrons epoxy primer on both side of the sheet and polyester top coat 15-18microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

CEMENT PLASTER (IN FINE SAND) 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand) including carriage of material in all leads and lifts

CEMENT PLASTER (IN FINE SAND) 20 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) including carriage of material in all leads and lifts

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade new work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of material in all leads and lifts.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) including carriage of material in all leads and lifts.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material in all leads and lifts.

Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) including carriage of material in all leads and lifts.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work including carriage of material in all leads and lifts.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of material in all leads and lifts.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall.15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design.) including carriage of material in all leads and lifts.

Providing and fixing of M.I. Union for wash basin or sink 32 mm dia. confirming to BIS specifcation including carriage of material in all leads and lifts.(ESS-ESS/ CZAR/ NOVA)

Providing and fixing C.P. brass soap dish with C.P.brass brackets fixed to wooden plugs with C.P. brass screws, and confirming to BIS specifications, including carriage of material in all leads and lifts.

Providing and fixing PVC floor trap (finolex) ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of material in all leads and lifts. (i) 110 mm X 75 mm nominal size.

Providing and fixing ISI marked high pressure PVC (finolex) of working pressure not less than 4.5 kg/sqm, waste and ventilating pipes including fixing with approved adhesive etc. complete within all leads, lifts of materials and other incidentals. including carriage of material in all leads and lifts. (i) 110mm nominal size.

Providing and fixing brass full way value with wheel (confirming to BIS Specifications) including carriage of material in all leads & lifts. (ESS-ESS/CZAR/NOVA)

15mm nominal bore.

20 mm nominal bore.

Providing and fixing 100 mm dia cromium plated stainless steel grating confirming to BIS specifcation including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

610x510 mm bowl depth 200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

32 mm dia

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

15 mm dia nominal bore

20 mm dia nominal bore

Providing and fixing 15mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

Stone filling behind retaining walls : including carriage of material in all leads and lifts

Providing weapholes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 including carriage of material in all leads and lifts

Please Enable Macros to View BoQ information