Outside Painting including reapir and renovation at Canning SDH in the District of South 24 Parganas.

Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed.

Cleaning the concrete surface by removing dirt and debris, marking defectivelocations and removing loose concrete by careful stripping untill hard surfaceis exposed, cutting the concrete to regular shape, wire brushing the exposedsurface and removing debris from site complete as per direction of theEngineer - in - Charge.

Cleaning the exposed reinforcement preferably upto full diameter by wirebrush, applying two coats of polymer based rust removing compound left for24 hours, removing the coating and then applying two (2) coats of polymermodified anti corrosive protective coating formulated to inhibit the corrosionof einforcement as per manufacturer's specification

(a) Applying 2 coats of bonding agent with syntheticmulti functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification [Cement to be supplied by the Department]

Cement concrete (1:1.5:3) with graded stone chips 5.6 mm size withhexagonal square mesh wire netting, I.R.C. fabric mesh or X.P. M. fitted andfixed after tying the existing reinforcement on concrete without istributingthe same and with proper scarping and cleaning the reinforcement anddisturbed concrete with wire brush etc. after applying a coat of cemenincluding the cost of wire netting I.R.C or X. P. M. & cost of all handling andscaffolding complete as per direction of Engineer-in -charge. b) 37.5 mm thick

Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directedwithin a lead of 75 m. including stacking of steel (a) In ground floor including roof.

(a) In F. floor .

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS odes. (i) Pakur Variety in ground floor

In F.Floor

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (i) Tor steel/Mild Steel. in ground floor

In F.Floor

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hardwood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works. (c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work in ground floor

In F.Floor

Labour for taking out door and window frame including shutter for repair orreplacement of different parts of the frame & refixing the same including mending good all damaes complete. (Concrete and brick work for mending damage will be paid separately (a) Upto area 2.5 Sq.m In F.F

Taking out shutter of door and window, dismantling by parts (for repair or replacement of damaged parts) , reassembling and refitting and rehanging same with old fittings but with new screws as necessary.

Wood work in door and window frame fitted and fixed in position completeincluding a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). (d) Sal : Local In F.F

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but exclu ding the cost of hinge and other fittings (iii) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm (b) Sishu, Gamar, Champ, Badam,Bhola, Mogra, Hallak

Shutters of 2/3rd panel and 1/3rd glazed of doors and windows as per design (each panel consisting of a single plank without joint and with ordinary glass of 7.4kg. Per sq.m./3mm thick) fitted with putty bed and teak wood beads and nails including fitting and fixing shutters in position but excluding the cost of glass, putty, teak bead, nails, hinges etc. and other fittings, (iii) 35mm thick shutters with 19mm thick panel. (b) Sishu, Gamar, Champ, Badam,Bhola, Mogra, Hallak

Glazed shutters of doors, windows, fan light, clerestory windows etc. as per design (with ordinary glass of 7.4kg./sq.m. 3mm. Thick) fitted with putty bed and teak wood bead and nails including fitting and fixing shutter in position but excluding the cost of hinges and other fittings. cost of glass, putty, wooded beads etc.will be paid separately (iii) 35mm thick shutters (b) Sishu, Gamar, Champ, Badam,Bhola, Mogra, Hallak

Styles and rails of wooden shutters fitted and fixed complete. (Payment to be made on area of new work only) (iii) 35mm thick shutters (b) Sishu, Gamar, Champ, Badam,Bhola, Mogra, Hallak

Panel (made of single plank) of door and window shutters to design as directed (ii)19mm thick panel of size 30 to 45 cm width (b) Sishu, Gamar, Champ, Badam,Bhola, Mogra, Hallak

Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) (b) 40mm X 6mm, 200mm Length

Anodised aluminium barrel / tower / socket bolt (full covered) of approv edmanufactured from extruded section conforming to I.S. 204/74 fitted and fixed complete. (e) 150mm long x 10mm dia bolt.

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISImark.(Oxidised) (vii) 100mm. X 58mm. X 1.90mm.

Supplying, fitting and fixing hinge cleat in pos ition excluding the cost hinge andother fiffitngs. a) with 50mm iron Butt-hinge iii) Local Sal.

Supplying, fittingng and fixing single skin color coated trapezoidal profile for wallcladding, Roofshall be made of 0.4 Smm BMT (Base Metal Thickness) (0.50mm TCT(Total coated thickness ercluding paint), G550 (min 550 yield strength),. of Zincalume metallic coating (1S15965) with high Solar Reflectance Index (SRI) values or better colling as per thermatech technology, 1000-101 Smm effective cover width with five major corrugation, 28nmm high rib spaced at 203mm cle with subtle squareSuting in the pan and the end rib shull have anti-capillary groove and return leg. The steel sheet shall be fustened with 40 micron zinc coated or 25 micron zinc-tin alloy coated, hex head, self-drilling screw as per IS 3566-2002 Cluss 3 fastener. The base steel shall be coated with zinc-uluminium alloy Zincalume (AZI50 ) (i.e. 35% Al,43.4% Zinc, 1.6% Si) minimum of 150 g/m2 coating total on both sides, pre- painted with color bond XRHW (exterior roofing, waulling) paint system of 35 micron Super Duruble Polyester paint (SDP) with stable inorgunic pigment with no lead contents confirming IS15965. The sheet shall be fre from defects and have hrand marking of the manufacturer giving product details on the back of the sheet at regular interval confirming genuinity of the material) In Roof a) With 0.5 mm thick sheet

Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall) (i) 3 mm thick (weighing 7.4 kg/Sq.m)

Welding in M.S. structural work with gas or electric: b) Continuous weld.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (i) With 1:6 cement mortar (c) 15 mm thick plaster In Ground floor

In F.Floor

In 2nd Floor

(ii) With 1:4 cement mortar (c) 10 mm thick plaster (I) In Ground Floor

In F.Floor

Labour for Chipping of concrete surface before taking up Plastering work.

Neat cement punning about 1.5mm thick in wall , dado, windowsill, floor etc

Scraping of moss, blisters etc.thoroughly from exterior surface of wallsnecessitating the use of scraper, wire brush etc.(Payment against thisitem will be made only when this has been done on the specific directionof the Engineer-in-charge) In G.Floor

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. c) Premimum 100% Acrylic Emulsion. In Ground floor (Two Coat)

In First floor (Two Coat)

In 2nd floor (Two Coat)

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (a) One Coat In Ground Floor:

In First floor (Two Coat)

In 2nd floor (Two Coat)

Removing loose scales, blisters etc. from old painted surface and thor oughly smoothening the surface to make the same suitable for receiving fresh coat of paint

(b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

a) Priming one coat on steel or other metal surface with synthetic oilbound primer of app roved quality including smoothening surfaces by sandpapering etc.

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoo thening surface by sand papering etc. includ ing using of approved putty etc. on the surface, if necessary (a) On timber or plastered surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white)

(b) On steel or other metal surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white)

Renewing worn out putty of glass panes : (a) Panes not exceeding 0.2 Sq.m

Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming toIS:13592-1992 with all necessary clamps nails, including making holes inwalls, floor etc. cutting trenches in any soil through masonry concretestructures etc if necessary and mending good damages including joining withjointing materails A) UPVC Pipes: 110 mm. Dia.

B) UPVC Fittings: c) Bend 87.5 degree 110 mm. Dia.

M.S. works in brackets made from flats, angles, tees etc. to sizes specialy bent, twisted, forged; making holes drilled and fitted to rafter of trusses with necessary bolts, nuts, washer or screws etc. (length of straight not less than 230 mm)

Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge

Add 18% GST

Add 1% Cess