SPECIAL REPAIRS TO OFFICER SPORTS COMPLEX (P-49) UNDER SPECIAL REPAIR B/R AND PROVN OF OVERHEAD SHED AT MI ROOM SHOPPING COMPLEX AND PARKING SHED AT ASH II UNDER LBW AT NAVAL STATION BHEEMUNIPATNAM UNDER GE(P) NAVY KALINGA

Amount

Demolition of Brick work or stone boulders masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles.

Dismantling of wall and ceiling boards any thickness including cover fillets, including removing of dismantled material from work site.

M&L for providing and fixing gypsum board 10mm thick in ceiling fixed with screw as per manufacturers instructions.

Demolition of cement concrete (Unreinforced) in ground floor and pavings n.exc 15cm thickness (below or above ground level).

Removing loose and broken concrete by chiselling upto a depth of 80 to 100mm from columns, beams and similar structural members, cutting edges, cleaning the dismantled portion with wire brushes etc and picking to remove dust, dirt and other foreign particles etc and washing with clean water at desired pressure and removing debris to a distance not exc 50 meters.

M&L for Non shrink cementitious micro concrete mixed with 12.5mm grade stone aggregate using Renderoc RG of M/s Fosroc or techno-commercially equivalent by weight (18 Kg of aggregate : 25 Kg of Rendroc RG) all as per manufacturer's instructions laid to an average thickness of 80mm to 100mm on surfaces of columns, beams and similar structural members prepared vide item Sl.item No. 5 here in before with and including use and waste of watertight formwork.

M&L for Applying one coat of epoxy bonding agent of M/s Fosroc or Techno-Commercially equivalent, complete all as per Mfr's instructions, on old concrete surfaces prepared vide Srl item no.5 here in before with and including use and waste of water tight frame work to facilitate pouring of micro concrete.

Demolition of chajja drop/ roof projection drop of thin RCC section of depth 10 to 20 cm, thickness 8 to 10 cm and finishing the concrete surfaces with 1:3 CM.

Taking down chowkats or frame with shutter, (without taking off shutter from the frame) exc 1.5 Sqm but n.exc 4sqm each and removing from site.

Taking down existing roof treatment including plaster etc.

M&L for Brushing neat cement slurry with 3.0 kg of cement per sqm.

M&L for 15mm thick screed bed on concrete surface in cement mortar 1:3 with water proofing compound before carrying out water proofing treatment over roof slab. Note: WPC will be measured and paid separately as supply only

M&L for APP based polymeric membrane minimum weighing 3 Kg/Sq.m. and minimum 3mm thick reinforced with polyester non wove fabric (weight not less than 150 gms/Sq.m.) laid on primed surface after applying a coat of blown bitumen 85/25 grade @ 1.20 Kg/Sq.m. over bitumen primer @ 0.50 Kg per Sq.m. by forced application, applying another coat of hot blown bitumen 85/25 grade @ 1.20 Kg per Sq.m. over water proofing membrane and applying a coat of solar reflective bituminous aluminium paint @ 0.10 Kg per Sq.m. all as per the manufacturers instructions.

S&F Factory made UPVC door frame made of UPVC extruded section having an overall dimension as below (tolerance+1mm) with wall thickness 2.00mm + 0.2mm+0.2mm, corners of the door frame to be jointed with galvanized bracket and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S tube of size 19 X 19 mm and 1mm + 0.1mm thickness and 3 nos stainless steel hinges fixed to the frame, extruded section profile size 48 X 40mm complete as per manufactures specifications/ instructions.

S&F 24mm thick factory made UPVC door shutters made of styles and rails of a UPVC hollow section of size 59 X 24mm and wall thickness 2mm+0.2mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of MS Galvanized / plastic brackets of size 75X220mm having wall thickness 1.00 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised MS tube of size 20 x 20 mm and 1 mm + 0.1mm wall thickness. The lock rail made up of H section , UPVC hollow Section of size 100x24mm and 2mm+0.2mm wall thickness fixed to shutters styles by means of plastic/galvanized M.S U cleats. The shutter frame filled with a UPVC multi chambered single panel of size not less that 620mm having over all thickness of 20mm and 1mm+0.1mm wall thickness. The panels filled vertically and the tie bar at two places by inserting horizontally 6mm galvanized M.S rod and fastened with nuts and washers, complete as per manufactures specifications/instructions. Make : Rajshri Plastiwood/ Sintex/Duroplast Extrusion Pvt. Ltd

S&F Steel (white powder coated) crescent lock for UPVC sliding window/ door with necessary screws etc

S&F 5mm thick tinted glass, in square exc. 0.5 sqm in each pane fixed to PVC/ UPVC frame work.

Hacking out old broken glass any thickness size quality or description from /wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads.

S & F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n.exc 0.5 Sqm each pane.

M&L for ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based emulsion) @ 0.5 litre/ hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same.

M&L for ATT along the internal wall below concrete or masonry apron using chemical emulsion @ 2.25 litre per linear metre including drilling and plugging the holes etc in apron.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness as in roof covering.

Dismantling wrought iron or mild steel work of any description not otherwise provided for fencing etc. and removing unserviceable materials from site of work.

S & F Rolled sections as in main and cross beams, hip and jack rafters, purlin where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming Fe-410W (Gde-E-250) quality -A.

S & F 11 to 15 mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed the both ends each screwed ends to be fitted with washer and one hexagonal or square nut exc 5 cm but n.exc 10cm long.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws .

Taking down cement plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc built in cement mortar .

M&L for brickwork with fly ash bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar 1:6 complete all as specified and directed by the Engineer-in-Charge.

M & L rendering 10mm thick on internal surfaces of brick wall or concrete surface in cement mortar 1:6 finished even and fair without using extra cement.

M & L rendering 15mm thick on brick wall or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in two coats, first coat shall be 10 mm thick in CM 1:6 and second coat shall be 5 mm thick in CM 1:4, mixed with water proofing compound as per manufacturer's instructions in the outer layer finished even and fair. Note: WPC will be measured and paid separately as supply only

Supply only Integral Water Proofing Compound (ISI marked) of approved make.

M&L applying two coats of exterior emulsion paints over a coat of primer including preparation of new plastered external wall surfaces.

M&L for complete removal of existing treatment and applying two coats of exterior emulsion paints.

M&L for preparation of new plastered surfaces of walls and applying two coat of plastic emulsion over a coat of primer including 2 mm thick wall care putty on internal surfaces of wall.

M&L for complete removal of existing treatment of walls and applying two coat of plastic emulsion over a coat of primer including 2 mm thick wall care putty on internal surfaces of walls.

M&L 75mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection/ sub base and paving finished cement concrete surfaces even and smooth without using extra cement.

Taking down PVC (SWR) pipes of any dia including joints .

S & F PVC (SWR) pipes 150 mm dia single socketed in any length with rubber ring joints fixed to walls .

S&F 150 mm bore PVC (SWR) bends any radius .

S&F PVC shoe for 150 mm bore PVC (SWR) pipe.

S&F aluminium XPM wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples.

Excavation in trenches n. exc 1.5 mtr wide and n. exc 1.5 mtr in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, FRLS cable etc. n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in soft /loose soil.

M & L Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete, bed etc.

M&L for Reinforced Cement Concrete,1:1.5:3, type A1 (using 20mm graded granite stone aggregate) in foundations, including rafts, footings, plinth beams etc and the like .

M & L reinforced cement concrete M-30 (Design Mix Concrete) using 20mm graded aggregate as in slab supported on walls and the like.

M&L 20 mm thick granite (of any type) work table rubbed and polished in floors and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 20 mm thick screed bed in CM 1:4 complete all as specified.

Use and waste of form work to sides of foundation/ footings, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams and similar work for rough finished surfaces .

M&L TMT bars 10mm dia and over, as reinforcement. cut to length, bent to shape required including cranking bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified.

M&L TMT bars 6 to 8mm dia cut to length, bent to shape required including cracking bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm thick in soft /loose soil.

Removing excavated materials (soil) exc 250mm and n. exc 500m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed

Cutting holes for bolts, pipes etc in stone walls built in cement mortar and walls of cement concrete area n exc 150 Sqcm and depth of 10 cm.

S & F 16 to 20mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed the both ends each screwed ends to be fitted with washer and one hexagonal or square nuts exc 30cm long complete all as directed

M&L mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410 W (Gde-E-250) quality A.

S&F framed work such as grills, grating, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-O or Fe-310-O.

M & L applying two coats of synthetic enamel paint over a coat of red oxide Zinc chromate primer including preparation of new steel surfaces over 10cm width or girth.

M & L applying two coats of synthetic enamel paint over a coat of red oxide Zinc chromate primer including preparation of new steel surfaces n exc 10 cm width or girth.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish of the premises.

S&F 2nd class hard wood (well seasoned) plain, solid, straight, chowkats and frame, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified.

Taking down door chowkat or frame with shutter area n. exc 1.5 Sqm each (without taking off shutters from the frame).

M&L preparation of new wooden surface of any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint first grade quality over a coat of pink primer,.

S&F 4.8 mm thick sheet glass, ordinary quality & glazing with oil putty in square exc. 0.5 sqm in each pane complete all as specified.

M & L for Non skid/ matt finish ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 (Ist quality) as in floor set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 finished even and rough.

M & L for glazed ceramic coloured tiles 450 x 350 x 7mm thick (Ist quality) as in vertical surface such as skirting/dado set in neat cement slurry and pointed in coloured cement to match the surface, including 10mm thick rendering to receive tiles in CM (1:3) finished even and rough.

S & F in repair vitreous china, water closet pedestal pattern (white) 'P' trap (including fixing bolt, low level flushing cistern of 10 ltr capacity and seat cover).

S&F in repair wash hand basin of size 550x400 vitreous China (flat back or angle back type) including half pedestal and cutting for and pinning in ends of brackets or erecting stand including supply and fixing of waste coupling, waste pipe etc. .

S & F in repair PVC connection 15mm size with PTMT nuts of length 600 mm.

S&F in repair stainless steel tubular towel rod 20mm dia, D type 600mm long between flanges of brass chromium plated fixed with and including CP brass screws complete all as specified and as directed

S&F in repair soap dish, chromium plated brass, of approximate size 160x160x90mm, fixed to plugs with chromium plated brass screws .

S&F 40mm dia. PVC waste pipes for WHB/sink fixed to walls including fittings and connecting to multiple floor trap .

S & F PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls .

S & F PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls .

S&F 110 mm bore PVC (SWR) bends any radius.

S&F 75 mm bore PVC (SWR) bends any radius.

S&F 110 mm bore PVC (SWR) bends any radius with access door.

S&F 75 mm bore PVC (SWR) bends any radius with access door.

S&F 110mm dia. PVC (SWR) junction single (Single T) equal or unequal provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F 75mm dia. PVC (SWR) junction single (Single T) equal or unequal provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F PVC (SWR) vent cowls 110mm dia. .

S&F PVC (SWR) multi floor trap 75mm dia. outlet with grating including jointing with solvent cement complete all as specified and directed by the Engineer-in-Charge.

S&F in repairs, PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed by the Engineer-in-Charge.

S&F grating doom 125mm dia. with waste hole of PTMT (Min weight 40 gms) .

S&F 100 mm Cast iron Nahani trap grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90 degree) used instead of exposed portion of PVC sheet beading and panelling of wood grain printed PVC sheet to be fitted in the MS frame, welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent complete all as specified & directed.

S&F solid PVC door frames of size 100mm X 47mm made out of 5mm WOOD GRAIN printed PVC sheet used instead of plain colour PVC sheet and edges will be painted to match with printed sheet, reinforced with MS square tube complete all as specified & directed

S&F 125mm size MS butt hinges medium weight cold rolled fixed to frame complete all as directed.

M&L 200 mm long , aluminium alloy barrel tower bolts anodised extruded section ISI marked complete all as specified.

S & F 150mm size aluminium handles, cast type, anodised complete all as directed.

M&L for preparation of old plastered surfaces of ceiling and applying three coats of white wash, .

M & L rendering 5mm thick in cement plaster on ceiling in cement mortar (1:3) finished even and fair.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash .

Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out in soft/ loose soil .

M & L hardcore of broken stone or boulders of gauge n.exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface, .

M & L 100 mm thick PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in sub base/ floor, .

M & L 25 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) above sub base of floors.

Forming 20mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ in 100 mm thick concrete

Excavating soft/ loose soil in post holes (or similar holes) each n.exc 0.5 Cu.m getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm watering and removing surplus soil to a distance in n.exc 50m and making good surface.

Removing excavated material from site to a distance n.exc 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point.

M&L for Reinforced Cement Concrete, 1:1.5:3, type A1 (Using 20mm graded granite stone aggregate) in columns, pillars, piers, posts and struts etc and the like .

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular finishes rough surfaces of concrete etc finished rough surfaces of concrete complete all as specified.

M&L TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length , bent to shape required including cranking bending hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for single stanchions, built up of one MS tube conforming to IS 1161-1979 grade Yst 240 with flange plates, caps, bases, splices angle brackets, cleats and other connections.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 including gusset plate, including erection of vertical supports for holding purlins, rafters, base plates, nuts & bolts etc..

S & F 16 to 20mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed the both ends each screwed ends to be fitted with washer and one hexagonal or square nuts exc 5cm but n exc 10cm long complete all as directed

M&L for Polycarbonate corrugated sheet 2 mm thick of any colour as in roof covering/ cladding to wall fixed with self tapping screws.

M&L for Precast RCC benches with back rest and without arms of overall size 1.5m x 0.6m x 1.0m height & specifications are as follows:- (a) Seats : (i) 02 in No of planks of size 1.5 mtr length, 100 mm in width and 50 mm thick (b) Back rest : (i) 03 in no Planks of size 1.5 m in length, 100mm in width and 50mm thick (c) Legs : (i) 02 in no planks of size 0.6m in width, 1.0m in height and 100mm thick, including two coats of plastic emulsion over a coat of primer

M & L for preparation of new external surfaces of walls and applying two coats of cement based paint over a coat of primer .

M&L for Providing precast cement concrete in 1:2:4 type B1 in kerb stone, window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling), corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match.

Taking down carefully existing aluminium /copper conductor point wiring (light / fan / socket or power point) complete, with all fittings such as switches, socket, regulator, ceiling rose, utility light fittings and lamp holders etc and removing materials from site and making good the disturbed surfaces of walls roof and floor etc as per existing specification.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and fan regulators etc. for reuse at site. (Note : To be measured only when found serviceable in all respects complete for reuse)

Material and labour for point wiring for one light controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn carefully through existing/New concealed conduit along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including new pressed steel sunken boxes , concealed type with 2 mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc including testing on completion complete including making good disturbed surface .

All as per Item no 113 here-in-before but for one fan /E Fan point controlled by 1 one way switch and regulator .

All as per Item no 113 above but for one 3 pin switch socket outlet, 5 Amp on independent board .

All as per Item no 113 here-in-before but for one switch socket outlet, 5 Amp on same board with other switches all as specified and as directed

All as per Item no 113 here-in-before but for one16 Amp 3 & 5 pin switch socket outlet, independent with 4.0 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 4.0 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire .

Material and labour for sub main wiring with two single core PVC insulated un-sheathed cable with multi-stranded copper conductor of 2.5 sq mm size and drawing into and including concealed PVC conduit of 25 mm dia with earthing cable of PVC insulated un-sheathed stranded copper conductor of size 2.5 sqmm, single core, as earth continuity wire . (NOTE: 3 runs of 2.5 Sqmm cable and one run of PVC concealed conduit 25mm dia will be measured as one unit i.e. RM)

Material and labour for sub main wiring with two single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 6.0 sqmm and one single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 6.0 sqmm as in continuous earth wire drawn into and including PVC conduit medium grade 25mm dia ISI marked complete with fittings and fixings accessories complete with taking down old unserviceable submain wiring and making good the disturbed surfaces. Note: 3 runs of 6 Sq.mm & one run of 25mm dia PVC Conduit will be measured as one unit

Supply and fixing modular plate switch flush type, single pole one way 6 Amps 250 volts

Fixing only Switch flush button single pole one way 5 Amp, 240 volt ,. (Note : Material obtained from Srl item No. 112 here in before shall be used)

S&F switch piano flush type single pole two way 5 Amps, 230 Volts, 50 Hz .

Supply and fixing modular plate switch flush type, single pole one way 16 Amps 250 volts

Supply and fixing modular socket 6 Amps 5 pin..

Fixing only switch socket outlet 5 Amps flush type. (Note : Material obtained from Srl item No. 112 here in before shall be used)

Supply and fixing modular socket 6-16 amps 2/3 pin combined shuttered .

Supply and fixing modular step fan speed regulator 120 w ,2 module all as specified and as directed

Supply and fixing modular plates white colour suitable for flush metal boxes for mounting modular switches or sockets etc for 8 modules.

All as per item No. 128 here-in-before but for 6 modules .

All as per item No. 128 here-in-before but for 3 modules .

All as per item No. 128 here-in-before but for 2 modules .

Supply and fixing Flush metal box 1/2 module .

All as per item No. 132 above but for 6 modules .

All as per item No. 132 above but for 3 modules all as specified and as directed

All as per item No. 132 above but for 8 modules .

S&F ceiling rose surface bakelite three terminals .

Fixing only ceiling rose, surfaces bakelite three terminal. (Note : Material obtained from Srl item No. 112 here in before shall be used)

S&F sheet metal enclosure for MCB DBs, phosphatised, Powder coated , triple pole and neutral (TPN) 240 Volt , double door, suitable for 4 way with dim rail earth and neutral bar .

S&F sheet metal enclosure for MCB DBs, phosphatised, Powder coated , single pole and neutral (SPN) 240 Volt , double door, suitable for 8 way with dim rail earth and neutral bar .

S&F MCB, FP, rupturing capacity 10 kA, ‘C’ curve, 63 Amp, 415 volts ISI marked.

Supply and fixing MCB Single Pole (SP) C curve 10kA breaking capacity of 6 to 32 amps, 240 Volts in proper position .

S&F MCB, DP, rupturing capacity 10 kA, ‘C’ curve, 40 Amp, ISI marked.

S&F single pole and neutral enclosure with two pin earth plug with 01 Nos of MCB DP 20 Amps 'C' series.

S&F Indoor luminaire decorative batten for wall/ceiling mounting box type Extruded aluminium housing ,PC Diffuser, energy efficient saving LED BATTEN LIGHT 20W,230 V,50 HZ, slim integrated design easy install including twin twisted copper conductor flexible wire from ceiling rose to connector . [Make:CG Cat Part no.CCS-100-20-65-HL2-DP-NWH or equivalent as approved by GE]

S&F 1 x 150 watt LED high bay light new generation high luminous efficiency , fixed to false ceiling surface/ suspended with including necessary fixing accessories channel, MS clamp, nuts, bolts, washers, suspended rods of required size etc including taking down old unserviceable one.

S&F LED flood light 120 watt luminarie efficiency of 125 lm/ watt IP 66 protection, guard along complete all accessories prewired and hardware in high tensile with corrosive epoxy grey shade paint fixed to wall / ceiling including flexible wire from fitting to terminal point including taking down old unserviceable one.

S&F LED mirror light fittings 10 W, 230 V, 50 HZ suitable for indoor and outdoor applications complete .

S&F and fixing on wall security LED light fitting luminaries 1X25 W and including cable for connection from ceiling rose with 1.5 Sqmm PVC insulated stranded copper conductor (FRLS) cable including 25 mm GI bracket medium grade 1m long bent to shape including bolt,nut,washer,clamp etc .

Supply and fixing AC three phase static Electronic KWH energy meter of accuracy class 1.0, 240v, 50Hz, with backalite LCD Display, of rating 10-60A with transparent hinged type Box with six month History of energy in KWH with taking down old meter and kept in MES store yard with accessories .

S&F ceiling fan 1200mm sweep, decorative blades pearl white BEE 5 star rated with high air delivery at low voltages, with double ball bearing in ivory gold/ white colour including fixing of regulator, down rod of 19mm dia 300mm long and connecting up with flexible 3 core 1.5sq.mm twisted copper cable from terminal point to ceiling fan . (Havells Cat Part No. ES 40 or equivalent as approved by GE)

S&F Exhaust fan wall mount type 300 mm sweep metal body Heavy duty , single phase with louver shutter and connecting up including provision of hold fasts for fixing fan and louver shutter with cutting of hole and necessary PCC(1:3:6) .

S&F wall mounted Air circulators fans metal body 400 mm sweep 230 volts SP complete with accessories.

M&L for Earthing complete with 3.0m CI pipe 80 mm dia with flanged ends, centrifugally cast, class A, in any length, joints with suitable stainless steel nuts and bolts and sufficient slot up to 2.5mtrs length buried directly and preferably vertically in ground with top flanged ended 2.5mtrs below ground level welded/ connected with GI strip 32×6mm size on the top edge of the flange to bottom edge of the flanged for earthing including filling the pit with charcoal common salt surrounding the earth pipe including drilling 400 mm dia bore in any strata of soil to lower the CI pipe complete including necessary excavation and earth work PCC (1:3:6) type C-1 with 50 mm thick pre cast RCC (1:2:4) type B-1 cover slab and necessary testing on completion complete all as specified and as directed.

S&F 50mm dia. PVC waste pipes for WHB/sink fixed to walls including fittings and connecting to multiple floor trap.

Note : All item in the Schedule shall be completed in all respect as directed by the Engr-in-Charge.