Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹20.8 LAccepted-AOC | L1 | Accepted-AOC L1 | |
| 2 | L2₹22.5 L+₹1.7 L (8.11%)Rejected-Finance | L2 | Rejected-Finance L2 |
Tender Value
₹20 L
EMD Value
₹40,000
Closing Date
27 Jul 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Lt Col Aman Bhardwaj
Military Engineer Service Garrison Engineer (AF) No.1 Air Force Station No.1 Jamnagar 361 003
PROVN OF CERTAIN MINOR WORKS, MAJOR REVENUE WORK AND IMPROVEMENT OF E/M INFRASTRUCTURE AT AIR FORCE STATION JAMNAGAR
2023_MES_576548_4
8201/E8
Open Tender
Miscellaneous Works
Item Rate
180 days
Jamnagar
Please refer Tender Documents
6 documents required · 6 mandatory
₹500
GE (AF) Jamnagar No. 1
₹40,000
Yes
3 Aug 2023
1 Jul 2023
29 Jul 2023
1 Jul 2023
27 Jul 2023
8 Jul 2023
Amount
Material & Labour for sub main wiring with 2 run single core multistranded copper conductor cable, of size 2.50 Sqmm each, PVC insulated, unsheathed, fire retardant, low smoke (FRLS) drawn through and including PVC capping & casing not less than 20 mm wide with all necessary fitting and including one run single core multistranded copper conductor cable, of size 2.50 Sqmm, PVC insulated, unsheathed, fire retardant low smoke as earth wire, fixed on wall / ceiling complete. Note: 2 Runs of main cable and one run earth wire with PVC capping & casing will be measured as one running meter for payment.
S&F of LED Aviation obstruction light fitting die cast aluminium alloy housing, heat resistant, clear thick glass and accessories with LED lamp & driver, fixed in position & connecting complete Note : - (i) Super flux 302x5mm Nos LED's incorporate. (ii) Ingress protection : IP65 (iii) Inbuilt sensor for operating of on/off. (iv) Protection against to short circuit and surge.
Supply and fix MCBs single pole & neutral, 40 Amps, 240 volts with ‘B’ curve, fixed in sheet metal board complete including connecting.
Supply & laying XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium conductor 1100 volt grade of size 35 Sqmm 3.5 core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc complete all as specified & directed
Supply & laying XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium conductor 1100 volt grade of size 10 Sqmm 2 core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc complete all as specified & directed
Dismantling of high mast pole any height after carefully dismantling of LED light any wattage for reuse at location specified and carefully removing of cable, motor and all accessories and depositing it to MES store yard
Supply and fixing of service wire 2.5x2core for street light connection
Material & labour for Cross Arms bracings supports, clamps, back plate eye hook and back plates fabricated from structural steel sections including pole clamps stay clamps, D clamps nuts, bolts , washers welding bending cold or hot drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of aluminium paint complete all as specified and directed.
Supply and fixing 40 mm bore pipe , 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors
Material and labour for earthing complete with Galvenised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m deep below normal ground connected to GI strip 25x4 mm dia by means of bolts nuts check nuts and washer of galvanized steel, watering pipe of 20 mm bore, galvanised iron, medium grade, and 15 mm bore galvanised iron light grade for earth wire protection including all excavation earth work in any type of soil, PCC pit in PCC 1:2:4 type B-1 and RCC 1:2:4, type B1 for precast chamber cover 50 mm thick, reinforced with welded steel wire fabric or XPM Jali (weight not less than 4.00 Kg / sqm), with charcoal, salt, funnel complete all as shown in the electrical plate No 3 of SSR part –I and testing on completion.
Note : The Quoted rate for above item includes the cost of following : - (a) Earth electrode. (b) Main earthing lead from earth electrode to test point of 7.5 metre. (c) Material and labour for connecting earth electrode and earthing lead as specified. (d) Adequate quantity of charcoal dust, common salt and adequate quantity of chemical (e) All labour involved including testing of earth net work. (f) Excavation and earth work or drilling hole for electrode.
(g) P.C.C. pit and C.I. cover. (h) Funnel with watering pipe, wire mesh and copper lugs etc. as specified. (j) G.I. protection pipe of size ordered specified for protection of earthing lead from mechanical injury or tempering. (k) Test point. (l) Connecting lead from test point to main
M&L for civil work for foundation of street light upto height of 1.5m all as specified and directed
Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil.
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.
Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point
Material & labour for Sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete
Supply & laying ISI marked & conforming to IS - 5820 - 1970 unreinforced precast concrete cable cover Class LV , 250mm x 150mm x 40mm in trenches as protection to LT UG cable all as specified and directed by Engr-in-Charge
Supply & laying XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium conductor 1100 volt grade of size 25 Sqmm 4 core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc complete all as specified & directed
Supply, installation and commissioning of Submersible pump set 30 HP having discharge of 5000 LPM, and head 12m electric driven 415 V, TP suitable open well (outlet size for 200/250 mm dia Casing pipe size 200/250 mm) supply and Install complete inclusive of 20 metre long submersible cable, chain for supporting and taking out set mounting arrangement.
Supply and Fix Submersible Pump Starter For 30.0 HP Motor including PCC foundation , legs for panel at a height 1.5mtr all as specified and directed
Supply and fixing ductile iron pipes, socket and Spigot ends, of size DN150 mm dia bore, ISI marked Centrifugally Cast (Spun) Ductile Iron Pressure pipes conforming to IS:8329/2000 classification K-7 rating, suitable for push-on-joint(Rubber gasket-D jointing) with cement mortor lining inside the pipes and outside zinc coating with Bituminous finish coat as per IS:8329/2000 including EPDM rubber joints conforming IS: 5382 of 1985 all as specified and as directed by Engg-in-charge
Supply and fix Valve, butterfly conforming to IS 13095, 100 mm (4”) dia.
M&L for civil work for RCC column section 1ftx1ft height 8m cross support of DI pipe and clamps 50x6mm with nut &bolt arrangement at a spacing of 2m from bottom and fixing of DI pipe alongwith column & resting of pipe at the top and chain & pulley arrangement for taking out motor for maintenance of all as specified and directed
Supply and fix 100 mm dia 2 meter long hose conforming to IS 636 complete with male and female coupling conforming to IS 903
S&F DI fitting for DI spigot and socketed / flanged ends pipes like bends (any type, radius and angle) increasing, decreasing or double socketed / flanged tee pieces single branch 'Y' junction double branch, cross collars caps and plugs, connecting pieces one end flanged and other end socket or spigot and bell mouth pieces one end flanged other end tapering as bell mouth suitable for up to 300 mm bore pipe complete all as specified.
Supply install, testing ,commissioning Servo controlled voltage stabilizer (Confirming as per BIS:9815 Part I) 3 phase 50 Hz 75 KVA, naturally air cooled ,Outdoor ,unballenced type cooper wound digital display type ,Relay free smooth and silient operation with filling of transformer oil having the following specifications: (a)Input voltage 300V-480V or as per ground requirements (b) Output voltage stabilized at any designed/desired voltage 415 +/-1%(adjustable) (c) Rated frequency 50 Hz (d) No distortion in wave form (e) Response time not exeed 10 mille seconds (f) Sensitivity +/- 1% (g) Rate of correction 6 volt/Second for single phase and 20Volts/Second for phase to phase (h) No load losses....../-
......less than 0.5%,full load not less than 2.5% (j) Duty cycle continious 24x7(k) Efficiency not less than 98%, Digital display Voltmeter /Ammeter PROTECTION:- (a) Over load/Short circuit protection (b) High low voltage cut off (c) By pass arrangement in case of emergency (d) Single phase sequence change protection complete as specified and directed Make : Volina or its equilant
Supply & laying XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium conductor 1100 volt grade of size 120 Sqmm 3.5 core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc complete all as specified & directed
Material and Labour for provision of Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to using galvanised iron strip 32×6mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion.
Note : The Quoted rate for above item includes the cost of following : - (a) Earth electrode. (b) Main earthing lead from earth electrode to test point of 7.5 metre. (c) Material and labour for connecting earth electrode and earthing lead as specified. (d) Adequate quantity of charcoal dust, common salt and adequate quantity of chemical (e) All labour involved including testing of earth net work. (f) Excavation and earth work or drilling hole for electrode.
(g) P.C.C. pit and C.I. cover. (h) Funnel with watering pipe, wire mesh and copper lugs etc. as specified. (j) G.I. protection pipe of size ordered specified for protection of earthing lead from mechanical injury or tempering. (k) Test point. (l) Connecting lead from test point to main
S&F of flame proof, weather proof LED tube light fitting, type FLP-WP with LED-1 x 16/20 W including integral reflector made of aluminum alloy LM 79, with electronic driver, connector block, etc., and all accessories pre-wired and including connecting up with copper conductor cable of suitable type complete all as specified and directed.
Supply and Fix of stove enamelled black MS conduit 20mm dia ISI marked on ceiling or recessed as required & repairing & making good the same disturbed surfaces all as specified and directed.
Supply & installation of Air Cooled Inverter based split AC unit with cooling functions and suitable to operate at ambient conditions of (-10 to 46 Deg C in cooling Mode). Air conditioner will have following conditions:- (i) Refrigerent - R 410a (ii) EER - min 3.5 w/w (5 star rating) (iii) Tonnage - 1.5 (iv) Indoor Noise Level - Not more than 48 Db (v) Filter - (a) Must have PM 2.5 µ Filter (b) Electrostatic dust filter (c) Oxidizer dust filter (vi) Functions of remote : (a) Air directional control (b) Auto Timer (c) Economic sleep mode (d) Auto fan speed (e) Auto swing (f) Temp display (g) Turbo mode All specification will be as per IS-1391 (Part 2) 1992 Room Air Conditioners Make: Carrier/ Hitachi/ O General
Note:- Following will be inclusive in rate:- (a) Piping length upto 15 mtr will be inclusive in item (b) Installation will include fixing the outdoor unit on the platform as per direction of Engineer in Charge (c) Installation will also include civil work for making hole on the wall and putting the iron sleeve for passing the refrigerant pipe (d) Testing and commissioning of the Air conditioner to the entire satisfaction of Engineer in Charge (e) Contractor will provide warranty of 5 years for compressor from the date of installation (f) 5% of Air conditioner will be tested by the Garrison Engineer for Energy Efficiency and all the functions provision in the Air conditioner (g) Contractor provide complete free service in warrenty period by the company
Taking down / Dismantling carefully the indoor and outdoor unit of Split AC of capacity 1.5 TR / 2.0 TR with outdoor stand, plate for indoor unit and connected wiring, Transportation of complete set from old location to new location (with AF station Jamnagar), refixing of same AC at new location complete all as directed by Engr-in-Charge & detail as under:- (a) Fixing of indoor unit wall mounting type (to be installed inside the room) complete with, draining out arrangement for condensed water, fixing of inter connection pipe, all as directed. Fixing of cooling unit on wall shall be as per standard recommendation practice of manufacturers.
(b) Refilling of gas,Erection of condenser, compressor unit on outside of the building, fixed over old clamp / bracket, all as per standard practice of manufacturer. (c) All civil work such as making hole in the wall for passing of pipe etc, to be done, as directed by Engr-in-Charge including making good disturbed surface. (d) concealing of refrigerant pipe with PVC flexible pipe. (e) Extention of pipe due to site condition if required shall be measured and paid separately under respective items taken before.
S&F of Early Streamer Emission (ESE) lightening arrestors of color- steel white and material- stainless steel, installed at pole on building height upto 50 mtr and shall confirmed to NFC 17-102-2011, Efficency >095 &<_98 for level 1 with the length 80cm , ∆t For early stremer warning 40 µSec for 58 protection radius at Height of 5 mtr and connected copper cable to earthing all as specified and directed . Make SABO/ABB/powertec/Ashlok
Labour for fixing of lightening arrester above tower all as specified and directed
Supply and fix of Stranded copper cable coated in PVC is used as an internal earth conductor size 25 Sqmm single core and high resistance insulation confirming with IS-694, IEC 62305, IEC 62561 for connecting with lighting termination and complete all as directed.
S&F in of Sheet moulding compound (SMC) junction box of size 200X140X95mm mild steel clamps, nuts and bolts complete. Make : SINTEX model No GSJB-2014 or equivalent make Legrand / EPP Composite Pvt Ltd
Supply and fix of Test point terminal block made of gun metal or phosphorus bronze size of 75 mm x 75 mm x 25 mm drilled and screwed with 3 Nos 8 mm dia 25 mm long screw, fixed in and SMC junction box of size 170 x 170 x105mm hinged door fixed on wall complete all as specified and as directed. Note : SMC juction box will be measured and paid separately under respective items of this Schedule.
Material and labour for provision of earthing complete with copper plate electrode 600 mm x 600 mm x 3.15 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m deep below normal ground connected to 20×3mm copper strip by means of bolts, nuts, check nuts and washer of galvanized steel, watering pipe of 20 mm bore galvanised iron medium grade and 40 mm bore galvanised iron light grade for earth strip protection including.....
.....all excavation, earth work in any type of soil, PCC pit in PCC 1:2:4 type B-1 and RCC 1:2:4, type B1 for precast chamber cover 50 mm thick, reinforced with welded steel wire fabric or XPM Jali (weight not less than 4.00 Kg / sqm), with charcoal, salt, funnel complete all as shown in the electrical plate No 3 of SSR part –I and testing on completion. Note : (i)Earth result after installation completely should be less than 5 Ohm (ii)Quoted rates shall be deemed to include for earth strip with protection pipe of 7.5 M length.
Supply, installation, testing and commissioning DUCT (square/ rectangular) fabricated with galvanised steel sheet (G.S.S.) 0.80 mm thick sheet, 22 Gauge (GSG) having zinc coating of 140 gm/sq.m total on both sides complete with gaskets, elbows, splitters, vanes, supports etc. as per IS: 655/1963 (Revised upto date) and including with required scafolding work to install the ducts all as directed by Engr-in-charge Make : JINDAL / SAIL / ISPAT
Supply, installation, testing and commissioning of site fabricated MS channel / angle supports structure / pipe rack for the ducting work all as directed by Engr-in-charge
Material & Labour for Painting with two coats of silver synthetic enamel paint over a coat of red oxide primer to ducting outer surface all as speciied and as directed.
S t modi
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .