SPECIAL REPAIR TO TOILET, FACADE AND JOINERY OF AUDITORIUM AT MIL STN KOTA

Amount

Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water complete all as specified and as directed.

Material and labour for plastering 15 mm thick on stone masonry surfaces or other than fair faces of brick work or on one side of lathing (on vertical surfaces) in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for plastering 10 mm thick on fair faces of brick work or concrete surfaces on ceilings in cement mortar 1:3 finished even and fair complete all as specified and as directed.

M & L for preparation of new or previously untreated plastered/gypsum ceiling surfaces and applying two coat of oil bound distemper over and including 3mm thick wall care putty complete all as specified and as directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4 backing, complete all as specified and directed.

M & L for cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in floor 25 mm thick in sub base for laying tiles, pavings, floorings etc. complete all as specified and as directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for joint free non skid matte finish ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for joint free non skid matte finish ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm fixed on vertical surfaces as skirting, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 10 mm thick rendering in CM 1:4 backing, complete all as specified and directed.

M & L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like over and including 15 mm thick cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl cutting hole of 25mm dia for gas pipe if required complete all as specified and as directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed.

S & F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge and as per specification & drawing as applicable to item 08100A given in SSR Part – II (2020). (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Make:-Rajshri/Sintex/Accucel/Duraplast

S&F for factory made 30mm thick 100% Solid WPC ( Wood polymer Composite) Laminated Flush Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen/Balcony Doors. Make:-Rajshri/Sintex/Accucel/Duraplast

S & F 10 mm thick toughened frosted glass door shutters of Size area exc 1.50 Sqm but not exc 3 Sqm, including necessary floor spring hydraulically regulated, other side fixed on pivot, CP fittings and fixtures, CP handles, CP locking arrangement including necessary cutting & holes moulding and fixed complete as specified and directed.

S&F 10 mm thick Toughened glass as in partition/ fixed window including diamond edging all sided , eatching , lining and including monograme area nexc 0.50 Sqm each by sand blasting , including chromium plated " L" or " U" heavy duty clamps suitable for fixing of glass , min 4 nos per Sqm complete all as specified and directed

M & L for powder coated aluminium frame for doors, windows, ventilators (thickness of powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

M & L for powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium section (thickness of powder coating not less than 50 micron) weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150 mm long (1 no.). hinges type B-21 100 mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

Supply & fix sheet glass, ordinary quality, 5.5 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

Supply and fix Aluminium deco grill Cat No DG-104, 10 mm thick ,cut to required size/shape and fixed in position with and including stranded aluminium frame of F section of size 23.04x15.3x1.4mm thick all as per manufacturer instructions complete all as specified and as directed.

S & F 100 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed.

S & F brass skeleton 375 mm long tower bolts with cast brass plate and staples and rolled or drawn brass bolt complete all as specified and directed.

S & F brass alloy handle, fabricated type, 150 mm size, nickel chromium plated finish as per service grade number 4 of IS 1068: 1993 complete all as specified and as directed.

Supplying & fixing to walls and ceilings or laid in floors 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & fixing to walls and ceilings or laid in floors 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Taking up or down 15 mm bore of steel tubing and connections, including cleaning for refixing or removal to store or taken on schedule of credit complete all as specified and as directed.

Taking up or down 20 mm bore of steel tubing and connections, including cleaning for refixing or removal to store or taken on schedule of credit complete all as specified and as directed.

M & L in renewal of vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), complete all as specified and as directed. Make :- CERA (Cat No Conventional S1059101) /Jaquar (Cat Part No CWS WHT-551PNPP1841Z)/ Johnson (Cat Part No J8312) OR techno commercially equivalent makes specified in PS.

S & F in renewal of vitreous China squatting pan, ‘Orissa’ Pattern, of Size 580 x 440 mm white, with integral foot rests including PVC (SWR) ‘P’ or ‘S’ trap connecting to flush pipe and to anti siphonage pipe complete including making good to floor as per existing complete all as specified and as directed. Make :- CERA Cat No COVYNA S 3010109 / Johnson cat part No P0461PW0400/ Hindware cat part No J8365 or techno commercially equivalent makes specified in PS.

S&F in renewal of wall mounted EWC with integrated vitreous china flushing cistern of 10 Ltrs capacity, single unit of size 645 x 350 x 770mm with S or P trap incl slim soft close seat cover, complete set and making all necessary connections complete all as specified and directed. Make :- CERA cat part No S 1031103 / Hindware cat part No 20096 (P-15)/ Jaquar cat part No VGS-WHT-81851PN or technocommercially equivalent makes speciefied in PS.

S&F in renewal of vitreous china counter wash hand basin white with flat back of size 550x400 x 1600 mm, exclulding chain and plug, taps and porcelain stoper but incl PVC waste pipe of 32 mm bore, suitable size of waste fittings, one pair of 600 mm long cast iron brackets complelete all as specified and directed. Make :- Cera cat part No S 2020102 FG, / Johnson cat part No P 7312PW 50505 / Prayag cat part No 4724 or techno commercially equivalent makes specified in PS.

S & F in renewal PVC valveless, symphonic action type, flushing cistern, 10ltr capacity. Low level, white with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull or lever, complete as specified and as directed. Make :- CERA Cat No B1010102L/ Johnson cat part No J 85821C or techno commercially equivalent makes specified in PS.

S&F in renewal 15mm bore angle valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union as per hindware cat part No F 740039/Cera cat part No G1017201/Johnson cat part No T 2610 C 4 Complete all as specified and directed.

S & F in renewal of health faucet with 1 meter SS braided connection pipe complete all as specified and as directed. Make :- CERA Model-F 8030105AB (ABS)/ Jaquar ALD-565,/ Johnson cat part no J f8082A or techno commercially equivalent Makes as specified in PS.

S & F in renewal of towel ring of CP fixed with and including CP brass screws and wooden / plastic cleats (min wt 90 gms) all as for kitchen complete all as specified and as directed. Make :- Cera cat part No 5013115CH /Jaquar cat part No ACN-1121N / Hindware cat part No F 580003 or techno commercially equivalent Makes as specified in PS.

S & F in renewal of 15mm bore two way angle valve chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed with necessary fitting complete all as specified and directed. Make :- CERA cat part No G1017211 / Hindware cat part no F 740006 / Johnson cat part no JT 1643A or techno commercially equivalent Make specified in PS

S & F in renewal of Bib taps 15mm dia, chromium plated, long body, with CP flange all as per fixed in repairs complete all as specified and as directed. Make :- CERA cat part No G 1017152 /Jaquar cat pat no VGP-81037/ Hindware cat part No F 740011 or techno commercially equivalent makes specified in PS.

S & F pillar taps, 15mm dia, long body/swan neck, fancy type suitable for fixing to wash basin screwed for iron pipe and fixed with necessary fittings and including PVC connection complete all as specified and as directed. Make :- CERA Cat Part No F1003103 / Jaquar cat Part No COP -021PM/ Hindware Cat Part No F 740002 or techno commercially equivalent makes specified in PS.

S & F in renewal of Soap dish any type, fixed to plugs with chromium plated brass screws omplete all as specified and as directed. Make :- CERA Cat Part No F5013106CH/ Jaquar cat part No AKP 35731P/ Hindware cat part No F 450022 or equivalent makes as specified in PS.

S & F in renewal of chromium plated grating doom 100 mm dia, round with waste hole fixed on floor / Nahani trap fixed with 1:1 cement mortar complete all as specified and as directed.

S & F in renewal of brass, chromium plated toilet paper holder complete all as specified and as directed.

M & L in renewal of PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

S & F in renewal of stainless steel water jet of 15 mm dia of required length and fixed in EWC complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipes of size 100/110 mm jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipes of size 75 mm jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed.

S & F 110mm dia PVC(SWR) single socketed soil waste pipes in any length with rubber ring joints laid in trenches or in floor complete all as specified and as directed.

S & F 75mm dia PVC(SWR) single socketed soil waste pipes in any length with rubber ring joints laid in trenches or in floor complete all as specified and as directed.

S & F PVC (SWR) bends of any radius of 110 mm dia complete all as specified and as directed.

S & F PVC (SWR) bends of any radius of 75 mm dia complete all as specified and as directed.

Supply and fix in renewal of PVC SWR Nahani/ Floor trap plain with grating including jointing with solvent cement, dia of outlet 75 mm, water seal minimum 50 mm complete all as specified and as directed.

S & F PVC (SWR) junction single (single T) equal or unequal suitable for 100 mm dia complete all as specified and as directed.

S & F PVC (SWR) junction single (single T) equal or unequal suitable for 75 mm dia complete all as specified and as directed.

S & F in renewal frameless bathroom LED touch sensor mirror wall habnging of size 600 x 450 mm incl all necessary fittings complete all as specified and directed.

S & F in renewal vitreous China urinals twin with 6V DC dual flush sensor with all necessary fittings white in colour of size 350x295x685 mm complete all as specified and directed. Make :- Johnson cat part No P0020PW0703/ Cera cat Part No A 4020101/ HIndware cat part No 60021 or techno commercially equivalent makes specified in PS.

Supply and installation of Cladage 6mm thick exterior grade UV protected for wall/ceiling F- quality panels of standard size. Cladage interior panels are high-pressure laminates (HPL) as per EN 438-7, type EDF manufactured using patented technology (NT), Panels are double hardened including acrylic polyurethane resin which is thermally cured under high pressure & high temperature. termite free, water resistant. Explanation NT: Nonfading high performance acrylic polyurethane surface technology. Installation of Cladage panels will be done by high quality rivets with recommended aluminium ‘T’ section and ‘L’ section held by aluminium wall bracket with wind load and dead load slot as per design, anchored by standard Hilti/ Fischer or equivalent make anchor fasteners along with thermal separator, installation of Cladage panels will be done using rear ventilated principles only which is ensured by providing 200 Sqcm/ per meter (for free flow of air behind the façade) for the façade and using the framework with no horizontal section complete all as specified and directed. Make :- Oreo/ Alstone/ Greenlam or techno commercially equivalent make as specified in PS.

Supply & fixing vertical linear baffle box curtain closed C made out of aluminium extrusions of 1.2MM thickness. The baffle blade shall be in size of 30x 200x 3600 mm in powder coated finish of approved shade complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and as directed.

M & L for brick work with fly ash bricks of class designation 7.5 and non-modular size as per IS 12894: 2002, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M & L for brickwork with fly ash bricks of class designation 7.5 and non-modular size as per IS 12894: 2002, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed.

S&F 17-19 mm thick modular membrane kitchen cabinet door shutters and shelves (made out of HDHMR boards) in wood grain colour and half round edges, complete all as specified and directed.

S&F 16-18 mm wide & 1mm thick PVC edge banding pasted to edges of PVC furniture with suitable adhesive, complete all as directed.

S & F brass alloy handle, fabricated type, 100 mm size, nickel chromium plated finish as per service grade number 2 of IS 1068: 1993 complete all as specified and as directed.

S & F auto close hinges three dimentional adjustment with suitable mounting plate of extruded brass with nickel plated for corrosion resistance, bright finished for cubboard and cabinet shutters complete all as specified and directed.

Taking down carefully without point wiring by unscrewing from boards/ outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site or carrying to the store (To be measured only when found serviceable in all respects complete for reuse) complete all as specified and directed.

Supply and fixing 75 watt non integral flexible LED strip light with high brightness for outdoor applications, 3 KV surge protection, IP 65 Water Proof strip light including suitable drivers, adapters and connectors for connection, Warm white/ Icy blue / Blue with complete fitting all as specified and directed.

Supply and fix 09-watt new generation, energy saving, aesthetically designed, recessed mounted down light pressure die-cast aluminium heat sink & high efficiency long life COB LED mounted on MCPCB with high efficacy of 140 Lm/W used for enhanced lumen output, (Warm White colur) complete all as directed. Note:- Suitable opening for fitting of lights, T&P requirement for installation and fixing fixtures shall be included in the quoted rates.

Supply and fixing of LED focus colour light 8/10 Watt IP 67 water resistant, all weather, 2KV surge protection, with necessary MS Structure for mounting and complete fitting all as specified and directed.

Supply and fix concealed sub main wiring complete with and including four Nos single core PVC insulated, unsheathed flexible conductor FR-LSH cables 2.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through and including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories and fixed on walls and 1.5 sqmm one No single core copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable for earthing and connected to common earth dolly including cost of cutting chase and making good to disturbed surfaces of wall with cement mortar 1:3 including necessary plaster and pointing in cement mortar 1:3 with white wash/distemper/other paintings complete all as specified and as directed. Note 1- Four runs of 2.5 sqmm cable, one run of 1.5 sqmm cable and one run of conduit shall be measured and paid as one unit length. Note 2- Cost of cutting chase and making good shall be included in the quoted rate.

S & F miniature circuit breakers (MCB), single pole (SP), unenclosed, panel board type, screw type terminals for external copper conductors, C-type instantaneous tripping, rated voltage single phase, rated frequency 50 Hz, Rated current 6A to 32 A, Rated Short circuit capacity 10 kA, any type of fixation, Protection IP 20 complete all as specified and directed.

S & F miniature circuit breakers (MCB), two pole with one protected pole (SPN), unenclosed, panel board type, screw type terminals for external copper conductors, C-type instantaneous tripping, rated voltage single phase, rated frequency 50 Hz, Rated current 6 A to 32 A, Rated Short circuit capacity 10 kA, any type of fixation, Protection IP 20 complete all as specified and directed.

S & F double door MCB Distribution board of sheet metal enclosure, single pole and neutral, 4 way with 200 Amps rated bus bar, 240 volt, IP42 protection grade and fixed with PVC plug and screws and grouted in wall with M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate complete all as specified and directed.

M & L for concealed point wiring for one light or one fan or one exhaust fan controlled by one switch complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 1.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including modular/ non modular type, all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and directed. Note:- Cost of cutting chase and making good shall be measured and paid separately.

M & L for concealed point wiring for one 3 pin/ 5 pin 5 Amps socket outlet on the same board complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 1.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including modular/ non modular type, all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and directed. Note: Cost of cutting chase and making good shall be measured and paid separately.

M & L for concealed point wiring for one 3 pin/ 5 pin 5 Amps socket outlet on independent board complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 1.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including modular/ non modular type, all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and directed. Note: Cost of cutting chase and making good shall be measured and paid separately.

M & L for concealed point wiring for one 3 pin/ 5 pin 5/15 Amps socket outlet on the same board complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 2.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including modular/ non modular type, all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 2.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and directed. Note: Cost of cutting chase and making good shall be measured and paid separately.

S & F (3 pin and 2 pin) combined modular socket outlets, 6A, 2 modules, 240 V, AC, 50 Hz with earthing contact, rewirable, pillar type terminal, normal protection, unenclosed, without Shutter, Flush type, Design B complete all as specified and directed.

S & F modular switch, 1 way, 6 A, 1 module complete all as specified and directed.

S & F (3 pin and 3 pin) with common earthing pins, combined modular socket outlets, 6A & 16A, 2 modules, 240 V, AC, 50 Hz with earthing contact, rewirable, pillar type terminal, normal protection, unenclosed, without Shutter, Flush type, Design B complete all as specified and directed.

S & F modular switch, 1 way, 16 A, 1 module complete all as specified and directed.

Supply and fix metal flush box 12 module complete all as specified and directed.

Supply and fix metal flush box 3 module complete all as specified and directed.

S & F modular white cover plate with frame, 12 modules complete all as specified and directed.

S & F modular white cover plate with frame, 3 modules complete all as specified and directed.

S & F exhaust fan, AC, 50 Hz, single phase, 230 V, 300 mm sweep, 4 pole, heavy duty, metal body, 4 Nos blades, Insulation Class A, ISI marked including capacitor to ensure power factor more than 0.9 including louvers and all fixing accessories including making hole for fixing of exhaust fan of suitable size and making good the disturbed surface as per existing complete all as specified and directed.

Taking down ceiling fan 1200/1400 mm sweep / exhaust fans including disconnection of electric connection, dismantling blades and removing fan and blades to store complete all as specified and directed.

S & F LED tube fitting 4 feet 20 watts including tube with high power LEDs as light source and electronic driver complete all as specified and directed.

S & F LED tube light fitting 2 feet 10 watts including tube with high power LEDs as light source and electronic driver complete all as specified and directed.

ANNAPURNA ENTERPRISES (BID ID -3120912)

M/S MOHINI ENTERPRISES (BID ID -3120648)

S AND A ENGINEERS CONSTRUCTION CO (BID ID -3121550)

L P Singh and Co. (BID ID -3121052)

Pioneer Enterprises (BID ID -3121602)