REPAIR TO CERTAIN B R WORKS OF CENTRAL AMENITIES AREA AT NORTH OF RAILWAY LINE UNDER GE MISSAMARI

M&L brick work with sub class 'B' bricks, old size bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) including demolition of brick work masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

M&L 20mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm & 10mm) mixed with and including liquid water proofing compound in top layer as per manufacturer's instructions, finishing the surface even and smooth without using extra cement complete all as specified and as directed.

M&L preparation of new wall surface applying Two or more coats of 100% Premium acrylic exterior emulsion paint with silicone additives of required shade additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @2.20 litre/ 10 sqm complete all as specified and directed.

M&L Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 for finished even and fair complete all as specified and as directed.

M&L preparation of new wall surface applying Two or more coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, over 1 mm thick wall care putty,complete all as per manufacturer's specification complete all as specified and directed.

M&L Plain cement concrete type B-2 (1:2:4) using 40 mm graded stone aggregate as in sub base complete all as specified and directed..

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) size of tiles 300mm x 300mm, in floors etc. set and jointed in cementitious tile adhesive and pointed in white or coloured including 15 mm thick Screed bed or bedding layer of cement mortar 1:6, for laying floor finishes, laid over PCC 25mm thick average thickness Type B0 (using 20mm graded aggregate) as levelling course to roof surfaces finished even and fair, Dismantling existing unserviceable tiling including cement mortar bedding (but not backing), removing debries/ rubbish from the site complete all as specified and directed.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) size of each tile 600mm x 600mm, in floors etc. set and jointed in cementitious tile adhesive and pointed in white or coloured cement to match including 15 mm thick Screed bed or bedding layer of cement mortar 1:6, for laying finishes including dismantling/ taking down existing unserviceable tiling, cement mortar bedding, removal debries/ rubbish from the site complete all as specified and directed.

M&L 75mm thick cement concrete (1:3:6) type C-2( using 40mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M&L 5mm thick Rendering on concrete surfaces as in ceiling in cement mortar 1:3 for finished even and smooth without using extra cement including preperation surfaces of ceilings and applying three coats of white wash,complete all as specified and as directed.

M&L Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 for finished even and fair including preparation of new wall surface applying Two or more coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, over 1 mm thick wall care putty,complete all as per manufacturer's specification complete all as specified and directed.

M&L 20mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm & 10mm) mixed with and including liquid water proofing compound in top layer as per manufacturer's instructions, finishing the surface even and smooth without using extra cement including preparation of new wall surface applying Two or more coats of 100% Premium acrylic exterior emulsion paint with silicone additives of required shade additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @2.20 litre/ 10 sqm complete all as specified and directed.

M&L preperation of old surfaces of wall and applying two coats of white wash,complete all as specified and as directed

M&L preparation of old wall surface applying one coats of 100% Premium acrylic exterior emulsion paint with silicone additives of required shade additives @ 1.43 litre/ 10 sqm complete all as specified and directed.

M&L preparation of old wall surface applying one coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour,complete all as per manufacturer's specification complete all as specified and directed.

Taking down cement plaster on wall & ceiling of any description including racking out joints, hacking for key and scrubbing down with water etc complete including removing debries of the site complete all as specified and as directed.

Dismantling Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position of unframed work complete all as directed.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in any position of unframed work complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 including necessary preperation of surfaces and applying one shop coat of red oxide, zinc chrome primer complete all as specified and as directed.

S&F Prepainted galvalume aluminium zink coating GI based corrugated/semi corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F 0.8mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 120 gms/Sqm complete all as specified and as directed.

S&F in repair, Anodised aluminium snap grid frame work for false ceiling,Size of grid 605 x 605mm, includinng Hangers 4mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, with and including 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to Aluminium framework with screws, dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed.

M&L Preparation of new or previously untreated wood surfaces of any description, over 10 cm width or girth, not otherwise described appling applying two coat of synthetic enamel paint over one coat of pink primer,complete all as specified and directed..

Taking down Chowkhats or frames not exc. 1.5 sq. m each but with shutters (without taking off shutters from the frames)complete all as specified and as directed.

Taking down Chowkhats or frames exc 1.5 sqm and not 4.00 sq. m each but with shutters (without taking off shutters from the frames) complete all as specified and as directed.

S&F Pressed steel frames for doors with one or more rebates,1.25mm thk cold rolled mild steel sheet, size of frame 125 x 60mm including necessary fixing lugs, hinges, lock strike plate,etc., including necessary prepration of surface and applying a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L providing plain cement concrete type C-1, (1:3:6), (using 20 mm graded stone aggregate), as in fixing of hold fast, back filling of pressed steel door frame including necessary form work as required complete all as specified and directed.

S&F 35 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35 mm thick factory made 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part -I. section 8, clause 8.24(a), complete all as specified and as directed.

S&F Solid PVC door frame of size 50mm x 95mm made out of 5mm Plain colour PVC sheet reinforced with M.S. tube, suppling & fixing in opening as specified in SSR Part I, Section 8 complete all as specified and as directed.

S&F solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick Mouled PVC Sheet on the front face & 2mm plain colour PVC sheet on back face with particle board core & fixing in opening as specified in SSR Part-I, Section 8, complete all as specified and as directed.

S&F Powder coated Anodised aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators, partitions with one or more rebates including joining cleat for fixing etc. complete all as specified and directed Note:- Design/pattern, profile sizes and other dimensions shall be of standard sizes and as directed

S&F Powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified complete all as specified and directed Note:- (i) Glass/Wire Guage shall be measured and paid seperately at supply only rates (ii) Design/pattern, profile sizes and other dimensions shall be of standard sizes and as directed

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or revited, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work confirming to Fe.290. Gde-E-165, including necessary prepration of surface and applying a coat of red oxide zinc chrome primercomplete all as specified and directed.

Supply only 4mm thick plain sheet glass, ordinary quality fixed with Aluminum frame work n. exc 0.5 sqm in each pane complete all as specified and as directed.

Supply only 4mm thick frosted on one side glass, ordinary quality fixed with Aluminum frame work n. exc 0.5 sqm in each pane complete all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with Aluminum frame work complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F mild steel hold fasts; for securing chowkhats and similar small articles conforming to Fe-290 Gde-E-165 incuding treating hold fast with tar or coal tar black paint, sanding complete all as specified and as directed.

S&F 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F 150 mm Extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

S&F in repair 10 ltrs capacity low level valve less PVC syphonic action type flushing cistern white with inlet ball valve float and handle, PVC flush pipe, complete all as specified and as directed.

S&F in repair Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern including all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) PP soft close slim seat cover, hinges, accessories set complete all as specified and as directed.

S&F in repair, vitreous China table top wash basin of size 520x360x125mm (minimum size) white complete all as specified and as directed.

S&F in repair, Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and as directed.

S&F in repair, PVC connection 15mm size with PTMT nuts, 450mm long complete all as specified and as directed.

S&F in repair, Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repair, 600x450mm bevelled edge mirror of selcted quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified complete all as specified and as directed

S&F in repair, Vitreous China Urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; complete all as specified and as directed

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and as directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following course of treatment/specification from bottom to top, including of old unserviceable roof treatmnt including PCC padding complete all as specified and directed:- (i) Cleaning of old concrete surfaces of roof, picking sweeping cleaning the surface to remove all loose dust and thoroughly washing down with clean water and dried complete and providing PCC 25mm thick average thickness Type B0 (using 20mm graded aggregate) as levelling course (ii) Rendering 10mm thick in CM (1:4) mixed with and including water proofing compound as per manufacture instruction on existing roof surface true to level after applying cement slurry @ 3Kg/Sqm over RCC slab when concrete is green (iii) Applying one coat of bituminous primer @ 0.40 Ltr/Sqm. (iv) Supply and laying 3mm thick APP based olymeric membrane of approved manufacturer with weight not less than 3.50 Kgs per Sqm, reinforced with non-woven polyester febric weight not less than 160gms per Sqm. Polymeric membrane shall be taken to a height of 30cm(minimum) and than inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (v) One coat of Solar reflective bituminious Aluminium paint of approved brand to be provided over the APP membrane as per manufacturers instructions. Note : (a) Work shall be carried out through specialized applicator approvrd by GE. Contractor shall submit sufficent documents/Credentials in support of Applicator whom he wants the work excuted. (b) Laying APP based polymeric membrane shall be done torch on method as per manufactures instructions. (c) A minimum overlap of 100mm and 75mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instruction

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/Ceilings complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/Ceilings complete all as specified and as directed.

S&F 75mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S&F 110mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S&F 110mm bore PVC (SWR) Cowl complete all as specified and as directed.

S & F 110mm bore PVC (SWR) junction single (single T) equal or unequal with access door complete all as specified and as directed.

M&L100mm dia of outlet, Cast iron Nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

M&L100mm dia of outlet, Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S&F 32mm Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings laid in floors fixed to walls and ceilings or laid in floors, including taking out old unserviceable 15mm bore GI pipe complete all as specified and as directed.

Supplying and laying of 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings laid in floors fixed to walls and ceilings or laid in floors including taking out old unserviceable 20mm bore GI pipe complete all as specified and as directed.

Supplying and laying of 32mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings laid in floors fixed to walls and ceilings or laid in floors including taking out old unserviceable 25mm bore GI pipe complete all as specified and as directed.

S&F in repairs 15mm bore stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type), screwed both ends including necessary fittings such as sockets for pipe or for union all complete as specified and as directed.

S&F in repair 15mm bore Bib taps, fancy type, chromimum plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F in repair 15mm bore pillar taps, cast copper alloy with capston heads, chromium plated, fancy type, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed

S&F in repair, 125mm Brass chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed.

S&F in repair, health faucet suitable for 15mm dia pipe, 1.25 meter long easy flexible tube in chrome finish & wall hook all as specified and as directed

S&F 1000 Ltrs. Capacity rotational moulded polyethylene water storage tanks (cylinder vertical with class top) hoisted and fixed in position all as specified including 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight (20mm - 210gms), including dismantling existing unserviceable water tank of any description complete in all as specified and as directed.

Demoliation of cement Concrete(unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in Cement concrete in foundations, filling and mass concrete complete all as specified and as directed.

S&F 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including dismantling existing unserviceable paver block complete all as specified and directed.

M&L Heavy duty coloured vitrified tiles 300x 300x10mm thick set and jointed in neat cement slurry & pointed in white or colour cement to match set and jointed in neat cement slurry and pointed in white or coloured including 15mm thick Screed bed or bedding layer of cement mortar 1:6, for laying floor finishes, including dismantling existing unservicaeable floor tiling with cement mortar bedding and removing rubbish/debris off the premises complete all as specified and directed.

M&L plain cement concrete type B-1 (1:2:4) using 20 mm graded stone aggregate as in coping, hauncing, benching etc rounded or chamfered on edges complete all as specified and directed.

S&F in repair, 6mm thick bevelled edge mirror of selcted quality glass, mounted on 6mm thick commercial plywood with decorative wooden frame dully french polished and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified complete all as specified and as directed

S&F in repair, stainless steel (Grade 304) railing,grills etc made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed

S&F in repair, 5 to 7mm thick mosaic ceramic tilles fixed in floor/vertical surfaces of swimming pool including backing coat in cement mortar 1:3 set and jointed as per manufacturers instruction complete all as specified and as directed.

S&F in repair, 15mm thick suspended unit grid system ceiling with galvanised steel 'T' section frame work, which includes 1200mm long cross tees to be interlocked between main runners at 600mm centers to form 1200 x 600mm modules. Cut cross tees longer that 600mm to be supported independently. 600 x 600mm modules to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200mm cross tee. Suspension system unit grid system includes the following course, complete all as specified and directed:- (i) Main Runner: 'T' section of size 38 x 15mm and 3.6 mtr long (ii) Cross Runner: 'T' section of size 38 x 15mm and 1.2 mtr long (iii) Cross Runner: 'T' section of size 38 x 15mm and 0.6 mtr long (iv) Wall Angle Perimeter 19 x19mm thick 3 mtr long (v) The 'T' section shall be suspended from the soffit cleat, suspension fasteners and galvanised spring level clips at 1200mm centers (vi) 15mm ceiling panel having NRC of 0.9, RH99 and FL edge of size 595 x 595mm shall be placed into the above grid of size 600 x 600mm. The ceiling panel shall be conforming to ASTM E84 surface burning characteristic (Class A, Flame Spread: 25 & smoke developed:50) Note : (a) Work shall be carried out through approved manufacturer as approved by GE. Contractor shall submit sufficent documents/Credentials in support of whom he wants the work excuted.

S&F in repair, 12.5mm thick Echo block Gypsum board as in wall lining with the following course of specification, complete all as specified and directed:- (i) Fixing Perimeter Channel (0.55mm thick having one flange of 28mm and another flange of 18mm and web of 30mm) screwed and fixed to surfaces with screws as per manufactures instructions (ii) GI perforated wall bracket shall be screwd fixed on the surfaces using appropiately spaced at 800mm vertical centers and 610mm horizontal center, Section (having both flange 27mm, web 45mm, lip 6mm thickness 0.55mm) are spaced at 610mm center at not more than 610mm center screwed fixed to perimeter and wall bracket using corrision resistance 13mm wafer head self tapping screw. (iii) 12.5mm thick Echo block Gypsum board fixed with 25mm long drywall screw at 230mm center. Periphary, opening and cut edges should be at 150mm center including 50mm glass wool. All joints to be taped and finished with fibre tape and all purpose joint compound conforming to ASTM C475 Note : (a) Work shall be carried out through approved manufacturer as approved by GE. Contractor shall submit sufficent documents/Credentials in support of whom he wants the work excuted.

S&F in repair, wall cladding, volatile organic compound complaint and conforming to IS: 13745 -1993 Phenol bonded Bamboo wood 10mm thick wall cladding of size 1900mm x 133mm, Threshold & T-mold of size 1900mm x 44mm x 14mm including Thershold & T mold of size 1900mm x 44mm x 14mm including Threshold & T mold made of Eco friendly Bamboo wood, approved/certified bu GRIHA or IGBC having density of 1000 Kg/Cum to 1250 Kg/Cum, hardness 1000 Kgf to 1500 Kgf, finished with eco friendly UV coating in approved varient & colour/finishes, having tongue and groove interlocking system, providing and fixing to aluminium frame work made of 25mm x 25mm and making good to walls etc, with backlayment of 1mm high density EPE( expanded poly ethylene) foam under wall cladding complete all as specified and as directed. Note : (a) Work shall be carried out through approved manufacturer as approved by GE. Contractor shall submit sufficent documents/Credentials in support of whom he wants the work excuted.

S&F 4.5mm thick GEM finish BWF approved Pre-game line marking badmination court vinyl sport flooring laid with suitable premium quality adhesive 0.25 Kg/Sqm to 0.35 Kg/Sqm over the elastic mat and jointed with PVC welding bar of matching colour using hot air gun including game line marking as per standards including removing existing unserviceable flooring, preperation of old surfaces complete all as manufacturers instruction and as directed. Note : (a) Work shall be carried out through approved manufacturer as approved by GE. Contractor shall submit sufficent documents/Credentials in support of whom he wants the work excuted.

M&L applying three component high performance epoxy tile grout suitable for swimming pool including necessary preperation of surfaces, and jointing/pointing of tiles complete all as manufacturers instruction and as directed. Note : (a) Work shall be carried out through approved manufacturer as approved by GE. Contractor shall submit sufficent documents/Credentials in support of whom he wants the work excuted.

Please Enable Macros to View BoQ information