PROVISION OF SINGLE IN LIVING QUARTERS FOR OFFICERS, SPECIAL REPAIR TO ROAD AND CERTAIN SANCTIONED WORKS UNDER GE I CG PORBANDAR.

Amount

SCHEDULE 'A'

Surface excavation n.exc 30 cm deep averaging 15 cm deep and getting out in soft/loose soil including Clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots, and trees not exceeding 30 cm girth (measured one metre above ground level) and removing rubbish upto a distance of 50 metres complete all as specified and as directed..

Excavation over areas n.exc 1.5 M deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cessipts, manholes, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick using excavated soft/loose soil all as specified.

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point

M&L Hardcore of guage n.exc. 63mm, deposited spread & levelled in layers n.exc.15CM thick, watered & rolled/ rammed to a true surface using broken stone or boulders all as specified and as directed by engineer-in-charge.

M&L Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded granite stone aggregate) as in benching of man holes including forming centre channels half round or 1/4 section.

M&L Plain cement concrete, type C2, (1:3:6, using 40mm graded stone aggregates) as in foundation of manholes. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L Plain cement concrete, type D2, (1:4:8, using 40mm graded stone aggregates) as in foundation, filling and mass concrete etc all as specified and as as directed by engineer-in-charge. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L Precast cement concrete block masonary, type C1 (1:3:6 using 20mm graded stone aggregates) with solid blocks, exc 10cm in width and setting in cement mortar 1:6, complete all as specified and directed.

M&L Pre-cast RCC , type B1 (1:2:4, using 20mm graded stone aggregates) as in manhole cover slabs set in cement Mortar 1:4 and finished all exposed surfaces of concrete even and fair without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in foundation including raft footing foundation beam plinth beam bases for columns etc basement slab under reamed piles and mass concrete Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in slabs supported onwalls, beams and colums in floors, roofs, landings, balconies, canopies ,deck slabs and in shelves and the like complete all as specified and directed by Engr-in-charge Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in chajjas, floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in beams,cantilevers, bressumers and lintels over 1.5 mtr span complete all as specified and directed by Engr-in-charge. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in Columns,pillars,piers, posts and struts Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

Extra for forming fair finished channel or drain 30cm ginth (inner girth) in cement concrete using extra cement incl forms, moulds stopped.

Supply only integral water proofing compond

M&L 40mm thick Damp proof course in cement concrete, type B0, 1:2:4 (using 12.5 mm graded stone aggregates), including necessary form work with WPC as per manufacturer instruction by weight of cement.

Formwork to sides of column footing/plinth beam etc, rough finished surfaces of concrete flat.

Form work to soffits of suspended slab such as roof slab floor slab landing and similer work not exceeding 200mm thick (horizontal or sloping) ,for rough finished surfaces of flat concrete.

Formwork to chajjas including edges ,for rough finished surfaces of flat concrete.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc for rough finished surfaces of flat concrete.

Form Work to sides of pillars/ columns square or rectangular ,for rough finished surfaces of flat concrete.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide as in rough finished surfaces of concrete etc complete

S&F 2nd class hard wood plain,solid,straight chowkats and frames,wrought,framed rebated on the solid,rounded or chamfered,put together with glue pinned at joints

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by Engr-in-Charge.

S & F 30 mm thick factory made solid panel PVC door shutter conferming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming stiles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings ass as directed by Engineer-inCharge Make : RAJSHREE/SINTEX

S & F Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with 19x 19mm MS square tubes, provided with EPDM rubber gasket throughout the frame fixed in opening complete as per manufacturer's specifications and as directed by Engineer-in-Charge Make: RAJSHRI/SINTEX)

S&F Aluminium, anodised, barrel tower bolts 150 mm long of extruded section and fixed complete all as specified and as directed by Engr-in-Charge.

S&F Butt hinges, 100 mm medium weight, cold rolled mild steel complete all as specified and as directed by Engr-in-Charge.

S&F 150 mm long Extruded aluminium alloy handles, fabricated type,anodised (ISI Marked) complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 140mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F Brass chromium plated finials for 25mm dia curtain rod complete all as specified and as directed by engineer-in-charge.

S&F 25mm dia Powder coated aluminium decorative type curtain rod complete all as specified and as directed. Note: colour of curtain rod shall be approved by Engineer-in-Charge.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engr-in-Charge.

S&F MS hold fast of flat iron 25 x 3 mm conforming to Fe 410-0 or Fe 310-0.

M&L Mild steel CRS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips. etc complete all as specified and directed by Engr-in-charge.

M&L Mild steel CRS TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips. etc complete all as specified and directed by Engr-in-charge.

All as per above item No.40.00 but 5mm dia and over upto 10mm dia as in stirrups, spacers and binders etc complete all as specified and directed by Engr-in-charge.

S&F Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed by Engr-in-charge.

S&F powder coated Anodised aluminium frame (minimum thickness of powder coating 50 micron) for doors, shutters, sliding windows and windows ventilators with or without rebates including joining cleats for fixing etc. complete all as specified and as directed by Engr-in-Charge.

S&F 4 mm thick Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5sq. m in each pane all as specified and as directed by engineer-in-charge.

S&F Aluminium grill with suitable aluminium anodised frame F/H section manufactured by M/s DECO GRILL as per design No DG-104, 100mm x 5.5mm to 6.5 mm thick with necessary channels and clips complete all as specified and as directed by Engr-in-Charge,

S&F Neoprene rubber beading of U or C section suitable for 5mm thick glass fixed along with edges of aluminium glass panes of joinery, all as directed by Engineer-in-charge.

S&F UPVC, double flat / groove type, roller for sliding windows all as directed by Engineer-in-charge. Note: Rollers shall conform to the samples kept with the Engineer-in-Charge.

S&F 100mm long powder coated Aluminium starlock for sliding window shutters conforming to the samples held in the office of Engineer-in-charge.

S&F Size of grid 605 x 605 mm GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre complete all as specified and as directed by Engr-in-Charge.

M&L Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and as directed by Engr-in-Charge.

Ditto-but to curved surface complete all as specified and as directed by Engr-in-Charge.

Extra over item above for any sunk or curved moulding complete all as specified and as directed by Engr-in-Charge.

S&F wall panelling made up of UPVC foam profile with homogenous fine cellular structure having smooh outer intergral skin having 100mm wide tounge and groove design with 10mm thickness of required shade, the internal batten having 35mm width and 17mm thickness, The batten aligned horizontally along the wall with 50mm gap above the floor and below the ceiling. The internal batten shall be fixed 450mm centre to centre in between junction and corners should be covered with foam beading profiles including providing 17mm thick EPS Sheet as insulation and better rigidity of wall panelling between wall and paneling complete all as specified and as directed by Engr-in-Charge.

Providing and fixing Aluminum Composite panels in all coloures of approved brand for external / internal wall cladding at all heights and elevations including necessary aluminium composite panel consist of 3mm thermoplastic core of anti oxident LDPE sandwitched between two skin of 0.5 mm thick alloy sheet making a total sheet thickness of 4 mm. The surface shall be finished with PDVF base coating on the top side and service coating on the reverse side shall be with a polymer paint. The system to be fixed to the brick/stone/masonry/RCC walls/framed structure with necessary clamps, bracket and anchor fasteners fixed over and including base frame fabricated with aluminium square pipe of size 25mmx20mm with 1mm thickness in 600mmx600mm size grid including stainless steel screws, nut, bolts, washers, cleats, weather silicone sealent for groove filling, backer rods etc, complete all as per Manufacturer instruction and all as specified and as directed by Engr-in-Charge. All Clamps and brackets shall be hot dip galvanised minimum 80 micron thick and confirmed to IS : 4759 - 1996. The extruded aluminium sections shall be anodised in approved colour with anodic coating minimum 20 microns. (items include cost of aluminium frame, ACP Panels, Cramps, weather sealent, gasket, foam, fixtures, scaffolding, all machineries and any other fastening streps, nuts, bolts, rivets, washers, etc complete). The manufacturer shall also give guarantee/warranty for ACP panels for a period of Five years. Make of ACP:- ALUPEX/ALUDECOR/ALSTRONG.

M&L 75mm thick, Plain Cement concrete, type D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base of floors even and rough finished to receive topping layer complete all as specified and as directed by Engr-in-Charge.

M&L 50mm thick, Plain Cement concrete, type B-1, 1:2:4 (using 20mm graded stone aggregate) as in sub base of floors even and rough finished to receive topping layer complete all as specified and as directed by Engr-in-Charge.

M&L 40mm thick, Plain Cement concrete, type B-1, 1:2:4 (using 20mm graded stone aggregate) using water proofing compound @ 2% of weight of cement content finished even and smooth using extra cement. Note:- Waterproofing compound shall be measured and paid seperately.

M&L 25mm thick, Plain Cement concrete, type B-0, 1:2:4 (using 12.5mm graded stone aggregate) as in sub base to receive tiles.

M&L Glazed coloured ceramic tiles in verticle surfaces 300x 200x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match over backing bedding layer 10mm thick 1:4 and pointed in white or coloured cement to match etc complete all as specified and directed by Engr-in-charge.

M&L Joint free coloured non-skid ceramic tiles 8 to 9 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry over screed bed 15 mm thick 1:6 and pointed in white or coloured cement to match complete all as specified and as directed by Engr-in-Charge.

M&L Double charged Vitrified tiles 9 to 10 mm thick light shade (square/ rectangular) polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and white or coloured cement to match over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match as in floor etc , all as specified and directed by Engr-in-charge.

M&L 75mm thick PCC 1:3:6 type C1, (using 20mm graded stone aggregate) as in plinth protection, finishing concrete surface even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L Rendering 5mm thick in CM 1:4 with using water proofing compound @ 2% of weight of cement content over 10mm thick in CM 1:6 on surfaces of block masonry even smooth without using extra cement complete all as specified. Note:- Waterproofing compound paid seperatly.

M&L Rendering 5mm thick in CM(1:3) on ceiling finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L Rendering 15 mm thick in cement mortar 1:6 on fair faces of PCC block masonry and finished even and smooth without using extra cement

M&L Rendering 15 mm thick in cement mortar 1:6 on fair faces of PCC block masonry and finished even and smooth without using extra cement

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc.

M&L Preparation of new plastered surfaces of ceilings and applying three coats of white wash complete all as specified.

M&L Preparation of newly plastered surfaces of wall and applying Two coats of OBD over a coat of chalk white primer complete all as specified and as directed by Engr-in-Charge.

M&L Two coats of OBD on new plastered surfaces of ceiling over a coat of chalk white primer including preparation of newly plastered surfaces complete all as specified and as directed by Engr-in-Charge.

M&L Preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of zinc chrome primer, complete all as specified and as directed.

M&L APP based membrane course roof treatment in layers with following provisions:- (i) Applying one coat of bitumen's primer polymerized primer oil based coat, evenly @ 0.3 litre/Sqm as priming coat to the prepared surfaces, till the surfaces is properly impregnated and the solvent oil in the base primer shall be allowed to evaporated completely. (ii) Applying APP based pre-fabricated with non woven polyester reinforced membrane stabilized with fibre glass strands and top with grey mineral slates 3mm thick and weight not less than 3.50 Kg/Sqm by torch application method. (iii) Applying a coat of solar reflective bituminous aluminium paint @ 0.10Kg/Sqm over mineral surface.

M&L 150mm bore RCC pipes,NP2,laid and jointed complete with collars,including all levelling complete all as specified and directed.

S&F 15mm dia GI tubing medium grade galvanised,with all fitting complete all as specified and directed..

S&F 20mm dia GI tubing medium grade galvanised,with all fitting complete all as specified and directed..

S&F 1000 Litre three layered capacity rotational moulded polythylene water storage tanks (cylindrical, vertical with closed top ) hoisted and fixed in position all as specified and directed including provision of 200mm long 50mm bore GI nipples for inlet, outlet, overflow, drain out pipe including provision of check nuts complete all as specified and directed..

S&F 100mm dia grating round of PTMT (Minimum weight 25 gms) complete all as specified and directed.. Make : Prayag Cat no 111 or equivalent as approved by Engr-in-Charge

S&F PVC connections 15mm size with PTMT nuts, collar bush and spanner of length 300mm Make : Prayag Cat no 321K or equivalent as approved by Engr-in-Charge

S & F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches, in floors, fixed to walls including making good the disturbed surfaces complete all as specified.

S & F 110mm dia PVC (SWR) bend of any radius complete all as specified and directed.

S&F 100 mm dia PVC (SWR) 'P' or 'S' trap complete all as specified and directed.

S & F 100 mm dia PVC (SWR) floor trap with grating, out let including jointing to waste pipe fixed in cement concrete 1:2:4 complete all as specified and directed..

M&L Concreting bed to drain pipe of 150mm bore pipe including packing under and haunching against the sides of pipes after they are laid and tested in Plain cement concrete 1:3:6 type C2 complete all as specified and directed.

Cutting into existing manhole/Septic Tank for connecting new drain pipe of 150mm dia and making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4) section in cement concrete 1:2:4 type B1,smooth finished and reforming benching , all as required.

S&F 10 lit.Capacity PVC valveless, syphonic action type, flushing cistern,low level, white, with inlet,ball valve, float and handle including brackets complete all as specified. Make : Prayag (Cat Pat No-501) or equivalent as approved by Engr-in-Charge

M&L Forming contraction (dummy) joints 65 mm deep x 10mm wide, filled with grade ‘A’ sealing compound complete all as specified and directed.

S&F Fancy type 15mm dia bib taps, chromium plated cast copper alloy complete all as specified and directed. Make:- CERA Cat Pat No-F1005151 or Equivalent complete all as specified and directed by Engr-in-Charge.

S&F Fancy type angle cock,15mm dia , chromium plated cast copper alloy,screwed down,high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. Make:- CERA Cat Pat No-F1014201 or Equivalent complete all as specified and directed by Engr-in-Charge.

S&F Fancy type Tubular towel rack, 20mm dia, brass CP, 45cm long between flanges complete all as specified and directed. Make:- CERA Cat Pat No-F5003102 or Equivalent complete all as specified and directed by Engr-in-Charge.

S&F Fancy type Toilet paper holder with flap guard,CP Brass Make: CERA Cat Pat No-F5002110 or Equivalent complete all as specified and directed by Engr-in-Charge.

S&F Fancy type Soap dish, CP Brass Make: CERA Cat Pat No-F5003106 or Equivalent complete all as specified and directed by Engr-in-Charge.

S & F Vitreous china wash hand basin, white, flat back, of size 550 x 400 mm including waste chain and plug or porcelain stopper but including cutting for and pinning in ends of brackets all as specified and directed. Make: CERA Cat Pat No-S2030121W or Equivalent

M&L 15 mm dia Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed Make: CERA Cat Pat No-F1005101 or Equivalent complete all as specified and directed by Engr-in-Charge.

S&F EWC double syphonic water closet pan of ivory colour (Cansino) with integrated flushing cistern complete including all fittings such as seat cover, flushing pipe, with flushing cistern Make :- Cera Cat Pat No-S1012110-S-TRAP-110-W or equivalent complete all as specified and directed by Engineer-in-charge.

M&L Preparation of new plastered surfaces of wall and applying two coats of Exterior Weather Proof Paint over a coat of primer complete all as specified and as directed.

Repair to pot holes, any depth, n.exc 1 Sqm each including sweeping free from dust and mud or water, scoring sunkened surfaces in roads, paths etc, cutting around edges to at least 25 mm in depth, making good by applying tack coat @ 5 Kg/10 sqm of paving bitumen blinded with 0.09cu.m of stone chippings, 6.3mm size and again well rammed (incl supply of premix binder and chipping) complete all as specified and directed by Engr-In-Charge.

Scarifying of picking gravelled, macadam or Bituminous macadam surfaces in area exc 400 Sqm,exc 50mm & n.exc 100mm deep complete all as specified and as directed.

M&L Preparing black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with air compressor to remove all loose dirt etc. complete all as specified and directed by Engr-In-Charge and Applying Paving Bitumen evenly a priming/tack coat @ 5 Kg per 10 sqm complete all as specified and directed by Engineer-in-Charge

Supplying, laying spreading premixed bituminous macadam using design mix formula, single layer with using mechanical paver using paving bitumen of penetration specified@ 4% by weight of total mix, rolled and consolidated to required camber and gradient with 8 to 10 tonne power roller to a uniform smooth surface etc complete all as specified, for consolidated thickness 75mm or less

Supplying, laying, spreading 40mm consolidated thickness of semi dense asphaltic bituminous concrete with design mix formula with Paving bitumen not less than 5.5% using Sensor paver, rolled and consolidated to required camber and gradient with 8 to 12 tonne power roller to a uniform smooth surface etc complete all as specified..

M&L Painting lines, dashes, arrows, letters, marking etc of 2 mm thick on new surface or previoulsy treated road surface with hot applied retro reflective thermoplastic road marking paint (white/golden yellow) conforming to MORTH (Clause 803.4) all as specified with 8% glass beads using special applicator machine with heating arrangement upto 160 degree C including cleaning and drying the existing road surfaces to ensure dust, oil, grease and moisture free surfaces before applying paint complete all as spcified and as directed. Make: Asian/Shivalik or equivalent as approved by GE

S& F Reflecting road studs /cat eye (two way) size 100X100X25 mm through polycorbonate lens shield body component light weight ribbed structure on bedded in road surface using cut back bitumen emulsion complete all as specified and as directed by Engineer-in-Charge. Make: Sinor infrastructure(DA-51) or equivalent in 3M/Dark Eye

S&F Solar stud 125X125X25 mm (Model DA 110-DHRUV) aluminium alloy and construction solar powered by nionocrystal solar panel type of battery. one high capacity NI-Cd rechargeable battery, View distance Approximate 1000 mtrs, LEDs- 010mm 3 pieces each side and total 6 pieces are used for high brightness of diffrenet colours, back up 12 hours of continuous lighting at night,red colour, super quality fixed with Epoxy adhesive complete all as per manufacturers instrucitons. Make -3 M/TATA BP Solar/SA Traffic Safety Kolkata /Bonus light PVT LTD Ahemdabad ASIN Control Mumbai

M&L Cleaning the surface by brushing with wire brushes for removing caked mud etc sweeping with compressor air blower to remove all loose dust and dirt etc/taking out dust existing material with compressed air and making the surface free from dust drying the surface and applying the one coat of polymeric modified bitumen emulsion (PMBE) by using self propelled emulsion distributing uniformaly or towed emulsion pressure sprayer equipped for spraying the PMBE uniformally and mopping the total undiluted PMBE @ 0.60 litre per sqm in one coat duly diluted in ratio 3:2 (PMBE 3 Litre : Water 2 Litre) and ensure uniform finish of total area complete all as per manufractures instructions complete all as specified and directed by Engineer-in-Charge. Make: IOCL/BPCL/Bharat petroleum Note-1 Actual quantity of PMBE shall be as per trial patch and approved by Engr-in-Charge. Consumption of PMBE shall be jointly recorded in MB for record purpose Note-2 Minus price adjustment as pro-rata of quoted rate shall be made if less quantity of PMBE as per trial patch and subsequently approved by Engr- in-Charge is used in work Note 3 Special care shall be taken to fill gape /crack with 6 mm to 2.36 mm size coarse sand as per requirement and quoted rates is included for repair of gapes/cracks Note-4 Quoted rates shall be deemed to included for trial patch of size 200 Sqm.

M&L Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed copper conductor FRLS 1100 Volts grade cable, drawn through and including PVC concealed conduit heavy duty grade ISI marked 20 mm dia (external), including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5 sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire including metal flush modular switch box with frame and cover plate for modular switches, sockets etc all as specified and directed by Engineer in Charge Note: Cost of cutting / chasing on wall and making good after repair shall be deemed to be included in quoted rate . Make of cable: Havells/ Finolex/ RR Kable/ KEI (a) One light point controlled by one switch.

( b) One 3 pin socket outlet, 6 amps,on same board

( c) One 3 pin socket outlet, 6 amps, independent,board.

M&L Point wiring complete with 2.5 sqmm single core PVC insulated but usheathed copper conductor FRLS 1100 Volts grade cable, drawn through and including PVC concealed conduit heavy duty grade ISI marked 20 mm dia (external), ISI Marked, including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling etc including 2.5 sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire for One 3 pin socket outlet. 15 amps,independent board including metal flush modular switch box with frame and cover plate for fixing of switches, sockets etc all as specified and directed by Engineer in Charge Note: Cost of cutting / chasing on wall and making good after repair shall be deemed to be included in quoted rate . Make of cable: Havells/ Finolex/ RR Kable/ KEI

S&F Modular switch 1 way, 10 Amps, 1 module complete all as specified and as directed by Engineer-in-Charge. Make: Legend (Arteour) / Schneider (zencelo) / hager (berker)

S&F Modular switch 1 way, 16 Amps, 1 module complete all as specified and as directed by Engineer-in-Charge. Make: Legend (Arteour) / Schneider (zencelo) / hager (berker)

S&F Modular socket, 6 Amps, 2/3 pin combined 2 module complete all as specified and as directed by Engineer-in-Charge. Make: Legend (Arteour) / Schneider (zencelo) / hager (berker)

S&F Modular socket, 6/16 Amps, 2/3 pin combined 2 module complete all as specified and as directed. Make: Legend (Arteour) / Schneider (zencelo) / hager (berker)

S&F Modular fan regulator, 120 watt, 2 modular (ISI marked) complete all as specified and as directed. Make: Legend (Arteour) / Schneider (zencelo) / hager (berker)

M&L Sub main wiring with two runs of 4.0 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 Volts grade cable fire retardant low smoke drawn through and including PVC concealed conduit heavy duty grade ISI marked 25mm dia (external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I including conduit accessories like bends, tees, junction boxes etc including 4.0 sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire fixed complete all as specified and directed. Note: Cost of cutting / chasing on wall and making good after repair shall be deemed to be included in quoted rate . Make of cable: Havells/ Finolex/ RR Kable/ KEI

M&L Sub main wiring with two runs of 6.0 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 Volts grade cable fire retardant low smoke drawn through and including PVC concealed conduit heavy duty grade ISI marked 25mm dia (external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I including conduit accessories like bends, tees, junction boxes etc including 6.0 sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire fixed complete all as specified and directed. Note: Cost of cutting / chasing on wall and making good after repair shall be deemed to be included in quoted rate . Make of cable: Havells/ Finolex/ RR Kable/ KEI

Supply and fix sheet metal enclosure for Triple pole and neutral DBs when MCBs to be used 4,way 415 V double door with 200 Amps bus bar. Make:Legrand/Schneider/L&T

S&F MCB SP 5/32 Amps 10 KA rupturing capacity 'C' curve complete all as specified and as directed by Engineer-in-Charge. Make: L&T/ C&S/ Legrand/ Schneider

M&L for MCB TPN 415 Volts 32 Amps Make: L&T/ C&S/ Legrand/ Schneider

S&F 1600 lumen recessed mounted LEDdownlight housing made of die-cast aluminium with diffuser and integrated electronic driver with high efficiency long life LED chips, PF> 90, system luminious efficiency >80, CCT 6500K, IP 20, Operational Voltage 220V-240V, 50/60 Hz including electrical connection with 3 core flexible conductor cable of appropriate size complete all as specified and as directed by Engr-in-Charge. Make: Philips Cat Part No DN 394B LED16S-6500 PSU WH/ or Equivalent from Wipro Note: The contractor should submit LM79 and LM80 test certificates of the manufacturers for the batch of light fittings supplied.

S&F 1200 lumen recessed mounted LEDdownlight housing made of die-cast aluminium with diffuser and integrated electronic driver with high efficiency long life LED chips, PF> 90, system luminious efficiency >80, CCT 6500K, Operational Voltage 220V-240V, 50/60 Hz including electrical connection with 3 core flexible conductor cable of appropriate size complete all as specified and as directed by Engr-in-Charge. Make: Philips Cat Part No DN 393B LED12S-6500 PSU WH/ or Equivalent from Wipro Note: The contractor should submit LM79 and LM80 test certificates of the manufacturers for the batch of light fittings supplied.

S&F 20W Surface/Wall mounted Batten LED Luminaire, extruded aluminium housing with PC diffuser and integrated electronic driver with high efficiency long life LED chips, CRI=80(Minimum) PF>0.95, System luminous efficiency >100 lm/Watt, Operating voltage 150V-270V including electrical connection with 3 Core flexible cable of appropriate size from ceiling rose to LED fitting complete all as specified and directed, fixed in repairs Make : Wipro Trim LED (LL20-281-XXX-65AL1/Philips (BN021C LED 20S PSU CW GR S2) Note: The contractor should submit LM79 and LM80 test certificates of the manufacturers for the batch of light fittings supplied.

Supply and lay double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & IS14930 ( Part I and II) for protection of underground calbes of size 63 mm outer dia with all fittings. laid in trenches / road/ nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc for cable protection all as specified (excavation and earth work shall be measured and paid separately) Make: Rex/Poly/Gemini

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 4core complete all as specified and as directed Make Havels/RR Cables/Polycab

S &F 32mm dia, 3-layer, PP-R (Poly propylene random copolymer) pipes SDR-11(PN-10), UV stabilised,ISI marked and antimicrobial fusion having thermal stability for hot and cold water supply including all PP-R plain and brass threaded poly propylene random fittings (such as elbow, tee, reducers, couplers, short pieces, connections, union etc,.) whatever required as per manufacturer instruction fixed on walls/ceilings/trenches complete all as specified and directed Make: SFMC/VECTUS

S &F PP-R Gate valves (Brass Insert) of 32mm bore

S&F BLDC Ceiling fan 1200mm sweep without remote and connecting up to and including provision of 23/0.0076 (or equivalent size in mm) flexible three core PVC insulated copper conductor cable from ceiling rose to fan, hanging rod of suitable size etc complete. Make: Orient,Havells /Crompton

S&F 300mm sweep Exhaust fan 240 V AC,heavy duty industrial type,metal body fixed as per manufacturers instruction, connecting with and including 2 corex0.5 Sqmm copper coduct PVC insulated and PVC sheathed three core cable complete. Make: CG,Havells(Ventil Air), Bajaj (Bahar)/ ORIENT (HILL AIR )/USHA (AERO)

Supply, install and testing of 25Litre Capacity Storage type water heater (Geyser),PVC body with brass line tank, electrically driven, BEE 5 Star Rated including 450mm long PVC flexible pipe for hot and cold water connections,anchor fastener of suitable size and plug top 16A complete all as directed by Engineer-in-Charge. Make: Bajaj/Havells/Racold

M&L Bore of 300mm Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 3 metres long, connected with earthing lead of size 25mm x 4mm dia galvanisedstrip to the earth test point 9upto 7.5m length) including earth work, returning, filling, fill compound to reduce soil sensitivity and high quality earth pit cover made of PCC all as specified and directed by Engr-in-Charge. Note:- The compound (earth enhance gel) to reduce soil resistivity should be suitable for the prevailing soil, IR value should be less than 5.0 Ohm. Excavation, earthwork returning and filling to be included in the quoted rate

SIBS CONTRACTOR

Vijay Construction Co

Raj brothers

S t modi

MADHAV ENTERPRISE

SURAJ ENTERPRISE

JAMNAGAR ELECTRIC AND MACHINERY CO