1457/ NKDA/Engg-36/2010-XI -Supplying office furniture in connection with interior furnishing of office rooms of all the floors of the proposed Administrative Building of New Town Kolkata Development Authority

Amount

Supply installation & Placement of Table: Combining the elegance of Wood, Metal and Glass with tops in Decorative Laminate in matt PU finish 18mm thick Inside radius - 700.0 mm Outside radius – 1350.0 mm Depth – 650 mm Cork Rubberized cork – 18mm thick Glass Frosted Glass 10mm thick Diamond cut finishing on edges Inside Radius – 1202.5mm Outside radius – 1402.5mm Depth – 200mm *Note: Angle sustained within arc surface is 60 deg. Under structure Modesty Panel MS Perforated 7 stage poweder coated coloueed sheet. Below Work surface : 0.8 mm (thick) x 665.0 mm (height) x 1345.0 mm (flat length) Above Work surface : 0.8mm (Thick) x 260 mm (height) x 1345.0 mm (flat length) Legs MS tube 1.6 mm thick Diameter 50.8 mm Height 604 mm.Construction & materials:- welded assembled. As per Direction of Engineer in Charge

Supply installation & Placement of File & Storage Cabinet: 2111(W) x 410 (D) x 2000 (H). Top Panel: 2211 x 410. Made of 22mm Thick (±1mm) Pre- laminated Particle Board. Side Panel: 1978 x 390. Made of 17mm Thick (±lmm) Particle Board. Back Panels:'3 nos Made of 4mm Thick (±lmm) Pre- laminated MDF. Bottom Panels: 3 nos Made of 16mm Thick (±lmm) Pre-laminated Particle Board.Top Hinged Door Panel: 440 X 1150. Made of 17mm Thick (±lmm) Particle Board. Glass Door Panel: 440 x 1150. Made of 17mm Thick (± mm) Particle Board frame with tempered glass. Bottom Hinged Door Panel: 440 x 766. Made of 17mm Thick (±lmm) Pre-laminated Particle Board. Shelf Panels: 3 nos ~1ade of 22mm Thick (±lmm) Pre- laminated Particle Board. Partition Panels: 1978 x 390. Made of 16mm Thick (±lmm) Prelaminated Particle Board. Surface Finish (Side Panels/Doors): Veneer Face, coated with Clear lacquer. Surface Finish (All other panels) Pre-Laminated. All thickness edges are edge banded with matching lipping. As per Direction of Engineer in Charge

Supply installation & Placement of Chair: It is made up of 1.4+-0.1cm thk hot pressed plywood upholster -ed fabric and moulded hr polyurethane foam. It has a injection moulded in glass filled pp which is upholstered with mesh fabric. The back consists of adj. Lumbour support made of injection moulde d pp having adj. Of 5.0+-0.1cm. It is moulded high resilence polyurethane foam of density =30+/- 2 kg/m3.it is made up of integral skin polyurethane foam with 6.0+-0.1 cm hgt. It also have swivel to & fro adj. With moulded pu armtop. The mechanism is designed with the following features:- 360 deg revolving type. Center tilt synchro. 4- position locking giving tilts angle to the chair. It is made up of injection moulded pp wihich is upholstered with foam & fabric. It is an adj of 3.0+- 0.1cm and is assembled over chair. It has an adjustable stroke of 10.0+-0.3cm. It is a high prssure die cast polished alu. & fitted with 5 nos. Twin wheel castors.the pedestal is 66.0+-0.5cm. Pitch center dia. (75.0+-1.0cm. With castors). The twin wheel castors are injected moulded in black pp having 5.0+-0.1cm wheel dia. Seat 49.5W x51.8D, Back 44.5 x 57.5 Seat All Hight 95.5 x 100.5 As per Direction of Engineer in Charge

Supply installation & Placement of Desk: DESK Top Panel: Made of 25mm Thick (±1mm) Particle Board clad with decorative post formed laminate on top side & balancinglaminate on bottom side with 30mm MDF pad. Post forming edge on longitudinal side. Modesty Panel: Made of 18mm Thick (±1mm) Pre-Lam Particle Board. Leg: Made of 18mm & 25mm Thick (±1mm) MDF Board with 2 side PU painted finish& hardness 2H in oxford cherry colour Over all Dimension 1800 x 900 x 750 as per direction of engineer in charge

Supply installation & Placement of Chair: The armrest top are injection moulded black pp.they are fitted to tabular armrest support made up of dia- 2.54+-0.03cm x 0.16+-0.0128cm thk ms erw tube & black powder coated (dft 40-60 microns). The tabular armrest support hold together the seat & back. The seat & back is made up of 1.2 +- 0.1 cm thk hot pressed plywood measured as per aq method described in ocp-qlta-pl14-18, upholstered with fabric & moulded pu foam with pvc lipping all around. The back foam is designed with countered lumbour support for extra comfort. It is moulded high resilence polyurethane foam of density =45+/- 2 kg/m3 and hardness load 16+-2 as per is: 7888 for 25% compression. The mechanism is designed with the following features:- 360 deg revolving type. 17 deg +-2 deg max tilt on pivot on center. Upright position locking.tilt tension adjustment. The tabular frame is cantilever type & made up of dia 2.54 +-0.03cm x 0.2+-0.016cm thk ms erw tube & black powder coated (dft 40-60 microns). It has an adjustable stroke of 12.0+-0.3cm. The bellow is 3 pieces telescopic type & injection moulded in black polypropylene. It is fabricated from 0.2+-0.02cm thk hr steel (is: dd 1079/hr) powder coated (dft- 40-60 microns) & fittedwith an injection moulded in black pp hub cap with 5 nos. Twin wheel castors.the pedestal is of dia 60.0+-0.5cm. Pitch center dia. (70.0+-1.0cm. With castors). The twin wheel are injected moulded in black nylon. Seat : (W)49.0cm x (D) 44.0cm Overall Dimensions of Chair Seat Height - min 42.4 to max 53.4cm. Height - min79.9 to max 90.9cm. Width & Depth of Chair as measured from pedestal - Width-70.0 cm and Depth-70.0 cm. As per Direction of Engineer in Charge

Supply installation & Placement of display cum storage cabinet:- Made up of 25 MM Thk pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge banded with matching with 2MM thk PVC lippng. Overall dimention 2350 x 1800 x 455, Slide Door Unit:- Made up of 25 MM Thk pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge banded with matching with 2MM thk PVC lippng for body panel like side, buttom, back and shelves. Shutters are made up of 25mm thk Mdf- one Sided pre-laminated board confirming to IS-14587 : 1998 with 0.4mm PVC membrane pressed on the top. Handles are provided for ease of opening. Storage is provided with lock for security. Over all dimension 2350x500x1800 mm As per Direction of Engineer in Charge

Supply installation & Placement of Chair: The seat is made up of 1.2 +- 0.1 cm thk hot pressed plywood measured as per aq method described in ocp-qlta-pl14-18, upholstered with synthetic leather over moulded hr resilence pu foam.moulded high resilence polyurethane foam of density =45+/-2 kg/m3 and hardness load 16+-2 as per is:7888 for 25% compression. The mechanismis designed with the following features: - up & down adj – 8 steps. • hgt adjustment armrest structure which is chrome plated & fitted with an armrest top. • fixed armrest top is pu moulded over metal insert. The mechanism is designed with the following features: - • 360 deg revolving type. • single pont control. • front pivot for tilt with feet resting on ground ensuring more comfort. • tilt tension adjustment. • 4-position locking and anti-shock feature. • seat/back tilting ratio of 1:2. Back can be adjusted in 5 position bu manually. Stroke of hgt adjustable spine is 7 cm .stroke of hgt adjustability is applicable for high back & mid back chair. It has an adjustable stroke of 10.0+-0.3cm. It is a high prssure die cast polished alu. & fitted with 5 nos. Twin wheel castors.the pedestal is 65.0+-0.5cm. Pitch center dia. (75.0+-1.0cm. With castors). Thetwin wheel castors are injected moulded in black pp. The powder coated welded tubular frame is made up of dia 2.54+-0.02cm x 0.16thk m.s.e.r.w tube with a connecting ms spine welded to it. Back spine is fitted to the frame assembly. Back: (W)48.0 cm x (H)76.0Cm, Seat : (W)51.0 cm x (D) 48.0 cm Overall Dimensions of Chair Seat Height - min 46.5 to max 55.5cm. Height - min 101.5 to max 117.5cm. Width & Depth of Chair as measured from pedestal - Width-76.0 cm and Depth-76.0 cm. As per Direction of Engineer in Charge

Supply ,Fitting & Fixing of Sofa and as per approved drawing & design / specification. NOMENCLATURE & DIMENSIONS (mm):-1 seater:Total Length – 1060 Total Height - 885 Total Width - 933 STITCHING:( type of thread : Nylon , Polyester) PITCH: 4 ( Pitch of thread i.e. Stitch per inch) LEATHER/PVC/FABRIC: (PU/PVC /Cotton/ Polyester/ Composite) PU Thickness (mm) : 1.0mm Weight (GSM) :Tensile Strength {wrap/weft} (Kg/cm) : Bursting Strength (Kg/cm2) : Adhesion (PVC/PU Backing) (Kg/cm) : Colour Fastness to Rubbing {Dry /Wet} (Scale 1-5) : FRAME MATERIAL (TROPICAL WOOD): Tropical wood Moisture Content ( 10 – 12 %) : 8%---12% Anti – Tremite Treatment (Borex Powder Treatment) : Kiln Drying :Thickness of Plywood used(mm) :7.5-15 Standard of Plywood used: Required Standard : IS 303 Commercial Plywood} Provide weight of recron filling used per seat SEAT FOAM: (DENSITY, TYPE) Thickness (mm) :30mm Density (Kg/m3):40# density hard Type of Foam (Virgin/Composite/Moulded/ Slabstock) : Upholestered in pure leather of cappuchino matt finish. Virgin Please provide layerwsie detail of foam used along with details of density & thickness Provide weight of recron filling used per seat BACK FOAM: (DENSITY, TYPE) Thickness (mm) :50mm+30mm Density (Kg/m3):28 #density medium -soft , 30# density medium-soft Type of Foam (Virgin/ Composite/Moulded/ Slabstock) : Virgin Please provide layerwsie detail of foam used along with details of density & thickness ARMREST FOAM: (DENSITY, TYPE) Thickness (mm) :10mm Density(Kg/m3):27# density hard Type of Foam (Virgin/Composite/Moulded/ Slabstock) : Virgin Please provide layerwsie detail of foam used along with details of density & thickness BELT/ WEBBING MATERIAL:Width of belt (mm) :40mm Total length of belt used (mm):520 Tensile Strength (Kg/cm) : Provide details of total length of wed & width of web used SPRING DETAILS ( S-SPRING / POCKET SPRING): Thickness of S-Spring (mm) :3.5mm Number of Springs used:4 Length of S-Spring used (mm) :510 Number of Pocket springs per seat:126 Thickness of Pocket Spring (mm) :80 Provide details of number of springs & Pitch LEG MATERIAL: Fixing of Leg : (Self Tapping Screw / Insert with metric threading) Self Tapping Screw Material of leg : (Plastic / Insert Moulding / Wooden/ MS / SS) Wooden Bush for Leg bottom : (PVC bush / Felt Pad) PVC bush, Type of Glue used : (Synthetic / Rubber base/ Water base/ Solvent Base) Synthetic As per Direction of Engineer in Charge

Supply installation & Placement of Chair: The seat & back is made up of 1.2 +- 0.1 cm thk hot pressed plywood measured as per aq method described in ocp-qlta-pl14-18, upholstered with fabric & moulded pu foam with pvc lipping all around. The back foam is designed with countered lumbour support for extra comfort. It is moulded high resilence polyurethane foam of density =45+/- 2 kg/m3 and hardness load 16+-2 as per is:7888 for 25% compression. The armrest top are injection moulded black pp.they are fitted to tabular armrest support made up of dia- 2.54+-0.03cm x 0.16+-0.0128cm thk ms erw tube & black powder coated (dft 40-60 microns). The tabular armrest support hold together the seat & back. The mechanism is designed with the following features:- 360 deg revolving type. 17 deg +-2 deg max tilt on pivot on center. Upright position locking. Tilt tension adjustment. The tabular frame is cantilever type & mad up of dia 2.54 +-0.03cm x 0.2+-0.016cm thk ms erw tube & black powder coated (dft 40-60 microns).it has an adjustable stroke of 12.0+-0.3cm. The bellow is 3 piece telescopic type & injection moulded in black polypropylene. It is fabricated from 0.2+-0.02cm thk hr steel (is:dd 1079/hr) powder coated (dft- 40-60 microns) & fittedwith an injection moulded in black pp hub cap with 5 nos. Twin wheel castors.the pedestal is of dia 60.0+-0.5cm . Pitch center dia. (70.0+-1.0cm. With castorsthe twin wheel are injected moulded in black nylon. Seat : (W)49.0cm x (D) 44.0cm Overall Dimensions of Chair Seat Height - 43.0cm. Height - 80.0cm. Width & Depth of Chair as measured from pedestal - Width-55.0 cm and Depth-61.0 cm. As per Direction of Engineer in Charge

Supply installation & Placement of decorative storage unit : Over all dimension 1400 x 470 x 760mm, Top Panel: Made of 25 mm Thick (+1mm) Particle Board clad with decorative post formed laminate on top side & balancing laminate on bottom side. Post forming edge at the front side. Colour in oxford cherry, Side Panels: Made of 18mm Thick (+1mm) Particle Board clad with decorative post formed laminate on side. Post forming edge at the front side. Other Panel: Made of 18mm Thick (+1mm) Pre-Lam Particle Board. Handles: Metal handles are provided on the shutter door at 128mm CD. As per Direction of Engineer in Charge

Supply installation & Placement of Storage unit: Construction & materials:- Over all dimention 911 x 1190 x 450mm, construction is a knockdown construction of 25mm thk and 18mm thk plb with metal cladding of 0.8mm thk crca (as per is:513) from outside. Side metal cladding is coated with epoxy polyster powder of 50+-10 microns thkness. Top options:- in case of 2.5’ (h)storage unit, wooden top is provided which is made of 25mm thk plb whereas 4.0’ and 4.5’ (h) storage unit are provided with 11mm thk bent metal tops made of 0.8mm thk crca (as per is:513) from outside . The metal tops are coated with epoxy polyster powder of 50+-10 microns thkness. Door & openng door: - two door opening The doors are made of 18mm thk plb with decorative laminate on one side and backing laminate on the other side. Shelving:- height wise adjustable shelf mounting holes provided on side panel for easy interchange of shelf height as required. Fixed shelf along with adjustable shelf provided for 4.0 hgt units. No fixed shelves for 2.5’ height storage units. 1 no. Adjustable shelf for 2.5’ / 4.0; / 4.5’ hgt and 1 no. Fixed shelf for 4.0’/4.5’ hgt without vertical partition 1190 hgt and 2 nos. Fixed shelves for 4.0 ‘and 4.5’ hgt with vertical partition in between for 950w & above. A4 size box files(85x345x285 wxhxd) can be stored vertically. Uniformly disturbed load capacity for each shelf is 40kg max. Skirting option:- the skirting units are provided with 150mm high skirting made of 0.8mm thk crca (as per is:513) and are coated with epoxy polyster powder of 50+-10 microns thkness. Leveller:- screw type adjustable leveler with plastic base provides vertical adjustment of floor unevenness and levelling of units . Back panel:- back panel is made of 18mm plb with option of decorative laminates as well as fabric finish .2.5’ (h) units consists of single back panel where as 4.0’(h) & As per Direction of Engineer in Charge

Supply installation & Placement of chair The seat is made up of 1.4± 0.1 chick hot - press 4 plywood upholstered with fabric and moulded polyurethane foam. It has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a sliding mechanism. SEAT SIZE: 50.0cm (W)x 49.0cm(D).The Back is injection moulded in Glass filled Polyamide which is upholstered with Mesh fabric. BACKSIZE: 50.0cm(W) x68.0 cm(H).The polyurethane foam for seat is of density 55± 5kg/m3.The armrest is made of Polyamide strture and polypropylene Housing with moulded PU armtop & Fixed. The inner tube of armrest is chrome plated. 304 grade SS fixed understructure with PVC buffer. As per Direction of Engineer in Charge

Supply installation & Placement of Table Over all dimension of 2100x2250x750mm, Primary Work Surface: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS- 12823:1990, Edge banded with matching 2 mm thick PVC lipping. Softclosing access flap with in-build power box are provided on work surface for wire management. Secondary Work Surface: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel: Made of 25mm thick MDF one side pre-laminate board confirmingto IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Understructure: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirmingto IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security. As per Direction of Engineer in Charge

Supply installation & Placement of Table: Over all Dimension 1135 x 1175 x 750mm Top Surface: PVC foiled: 25mm thick (+ 1). Base Material- 25mm MDF board. PVC Membrane foil on top. 8X2mm deep groove on centre of the table as graphics. Specially profile edge to prevent striping of foil & comfortable touch. Brown laminate on bottom surface. PU painted: 25mm thick (+). Base Material- 25mm MDF board. Combination colour Graphics on the centre. Colour as per colour chart. Brown laminate on bottom. Specially profiled edge for comfort. Understructure: Bend pipe understructure of MS. Powder coated. Pipe dia 38mm, 2mm thk. Understructure fitted with top by SS machine screws. Legs: MS Powder coated legs for PU top & SS legs for membrane top. 38mm dia pipe legs are fixed with understructure and table top. Glide: Plastic Glide fixed at the understructure to prevent the damage of table top during stacking. As per Direction of Engineer in Charge

Supply and Installation of Chair The seat should be made up of 1.4 ± 0.1 cm thick hot - pressed plywood upholstered with leather and moulded polyurethane foam.lt has a seat depth adjustment of 5.5 ±0.3 cm integrated in the seat through a sliding mechanism. SEAT SIZE: 51.0 cm (W)x 48.5 cm(D). BACK ASSEMBLY:The back should be made up of 1.3 ± 0.1 cm thick hot - pressed plywood upholstered with leather and moulded polyurethane foam. BACK SIZE - 51.0 cm(W) x 65.5 cm(H). POLYURETHANE FOAM: The moulded polyurethane foam for seat should be of density = 40 ± 5kg/m3. . ARMRESTS :It consist of fixed armrest which should be made up of polished stainless steel structure with Leather arm-pads.4. SLED BASE FRAME: The Chrome plated welded tubular frame should be made of Dia 3.2±0.03 cm x 0.2±0.02 cm thk M.S. Round tube.The frame should be fitted with plastic caps . a - of injection moulded glass filled Polypropylene. As per Direction of Engineer in Charge

Supply and Installation of chair: the cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth (6+/- 0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is operated with button. Armtop is made up of PU molded over plastic inner. The mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine. The neckrest assembly consists of upholstered neckrest inner(material-poly propylene) with moulded polyurethane foam and polyster fabric. upholstered inner shall be fixed to neck rest cover. neckrest shall be fixed to back assembly through neckrest spline. Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 109.3 to max 124.4 cm. Seat height - min 44.5cm to max 54.5cm. Dimensions tolerance / variations shall be within +/- 1 cm. 26 As per Direction of Engineer in Charge

Supply installation & Placement of Table: MAIN DESK Size: 2400 (W) X 900 (D) x (D) x 750 (H). Main Top: 2400 x 900Made of 68mm Thick (±lmm) combination of ~10F, Particle Board and Solidwood (batton construction) with top Veneer face coated with clear lacquer. Side Panel: 683 x 600. Made of 60mm Thick (±lmm) combination of MOF, Particle Board and Solidwood (batton construction) with top Veneer face coated with clear lacquer. Modesty Panel: 2240 x 600. Made of 17mm Thick (±lmm) Particle Board with Veneer face, coated with Clear lacquer. All thickness edges are edge banded with matching lipping. MAIN DESK Size: 1800 (W) x 900 (D) x 750 (H). Main Top: 1800 x 900. Made of 68mm Thick (±lmm) combination of MDF, Particle Board and Solidwood (batton construction) with top Veneer face coated with clear lacquer. Side Panel: 683 x 600. Made of 601Tl1TI Thick (±lmm) combination of MDF, Particle Board and Solidwood (batton construction) with top Veneer face coated with clear lacquer. Modesty Panel: 1640 x 600. Made of 17mm Thick (±lmlTl) Particle Board with Veneer face, coated with Clear lacquer. All thickness edges are edge banded with matching lipping. ERU: Size: 1200 (W) x 440 (D) x 650 (H). Top Panel: 1200 x 440. Made of 22mm Thick (±lmm) Particle Board. Side Panel: 440 x 546. Made of 17mm Thick (±lmm) Particle Board. Back Panel: 1164 x 546. Made of 17mm Thick (Umm) Particle Board. Bottom Panel: 1200 x 440. Made of 17mm Thick (±lmm) Particle Board. Hinged Door Panel: 340 x 542. Made of 17mm Thick (±lmm) Particle Board. Shelf Panels: 546 X 404 and 344 x 404. Made of 16mm Thick (±lmm) Part.J9,e Board. Surface Finish: Veneer Face, coated with Clear lacquer. All thickness edges are edge banded with matching lipping. PEDESTAL Size: 443 (W) x 510 (D) x 635 (H) Top Panel: 443 x 510. Made of 22mm Thick (±lmm) Particle Board. Side Panel: 490 x 549. Made of 17mm Thick (±lmm) Particle Board. Back Panel: 408 x 548. r~ade of 16mm Thick (±lmm) Particle Board. Bottom Panel: 408 x 473. Made of 16mm Thick (±lmm) Particle Board. Drawer Front: 440 x 15B (Top Drawer) & 440 X 190 U4iddle & Bottom drawers). Made of 17mm Thick (±lmm) Particle Board. Surface Finish: Veneer Face, coated with Clear Lacquer. All thickness edges are edge-banded with matching lipping. As per Direction of Engineer in Charge

Supply installation & Placement of Chair: : Upholestered in pure leather, 304 grage SS understructure made up of 1.2+-0.1cm thk hot pressed plywood measured as per qa method described in ocp-qlta-pl 14-18 & upholstered with fabric or synthetic leather and moulded hr polyurethane foam .the foam is designed with counter lumber support for extra comfort.it is moulded high resilence polyurethane foam of density =45+/- 2 kg/m3 and hardness load 16+-2 kgf as per is:7888 for 25% compression.the seat & back are arrested together with spine made up of 0.8cm+-0.05cm thk hr steel and is powder coated (dft 40-60 microns).the armrest assembly comprises of 3 parts viz. The armrest support tube & pu armrest & the armrest top. It is made of 2.54+- 0.03cm x 0.16+-0.0128cm thk m.s.e.r.w. support tube and chrome plated. The ou armrest is made of black integral skin pu foam with 50-70 shore (a) hardness & reinforced with ms insert. The top is made up of abs & upholstered with foam & leather.the mechanism is designed with the following features: - • 360 deg revolving type. • seat back tilting ratio is 1:1.5. • front pivot for tilt with feet resting on ground ensuring more comfort. • tilt tension adjustment. • 5 position locking with anti shock back mechanism, which prevents the backrest from impacting the user when lock i realesed. • static seat depth adjustment = 5.0+-0.5cm with 5 position locking. It is designed with 360deg revolving type without back tilt. It has an adjustable stroke 0f 9.0+-0.3cm.it has an adjustable stroke 0f 12.0+- 0.3cm. The bellow is 1 piece and blow moulded in black pu. It is made up of die-cast aluminium with buffing finish .it is fitted with 5 nos twin wheel castors. The pedestal pitch center dia is 67.0 +- 0.5cm pitch center dia. (77.0+- 1.0cm with castors). 5 no twin wheel castors are injected moulded in black nylon .Back: (W) 53 cm x (H) 95.4 Cm, Seat : (W) 54.6 cm x (D) 49 cm Overall Dimensions of Chair Seat Height - min 49.9 to max 58.9 cm. Back Height - min 134.9 to 143.9 cm. Width & Depth of Chair as measured from pedestal - Width 77 cm and Depth 77 cm As per Direction of Engineer in Charge

Supply installation & Placement of chair : The seat is made up of 1.4± 0.1 chick hot - press 4 plywood upholstered with fabric and moulded polyurethane foam. It has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a sliding mechanism. SEAT SIZE: 50.0cm (W)x 49.0cm(D).The Back is injection moulded in Glass filled Polyamide which is upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 6.0±0.1cm. BACKSIZE: 50.0cm(W) x68.0 cm(H).The polyurethane foam for seat is of density 55± 5kg/m3. It is made of glass filled Polyamide arm structure with PU arm top and height adjustment of 7.0 ±0.5cm.The arm top has swivel and To-For movements. To-for movement is 6.0± 0.5cm.The inner tube of armrest is chrome plated. The mechanism is designed with the following features:• 360° revolving type.• Centre tilt Synchro• 3 position (including upright lock) giving option of variable tilt angle to the chair with anti shock feature, Head Rest & intigrated Coat hanger The Headrest is injection moulded din Glass Filled Polypropylene which is upholstered with foam and fabric has an adjustment of 6.0± 0.1cm & its assembled over the Full back chair. The pneumatic height adjustment is chrome plated with an adjustment stroke of 9.0 ± 0.3cm.The pedestal is High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal is 65.0±0.5 cm P.C.D. The twin wheel castors are injection moulded in black Glass filled polyamide having 6.0±0.1cm wheel Diameter. The Chrome plated tubular frame is made of Día 2.8±0.03 cm x0.2±0.02 cm the M.S. Round tube. The frame is fitted with plastic caps made of injection moulded glass filled Polypropylene. -75(W)* 75(D)* 115-130(H)* 44.5-53.5(SH). As per Direction of Engineer in Charge

Supply installation & Placement of Chair: The seat & back are made up of injection moulded high impact strength polypropylene plymer compound with indoor grade uv resistance. The powder coated (dft- 50+-10 microns) a welded tubular frame is made from dia2.22+-0.03cm x 0.16+-0.0128 cm & 3.5+-0.03 cm x 1.5 +-0.03cm x 0.16+- 0.0128cm m.s. e.r.w. tube. The tubular frames is made from dia2.22+-0.03cm x 0.12+- 0.0128 cm & 3.5+-0.03 cm x 1.5 +-0.03cm x 0.16+- 0.0128cm ss 202 grade tube. The tubes are buff polished to give shiny finish the powder coated (dft- 50+-10 microns) welded beam ss 202 under structure is made from dia5.08+-0.03cm x 5.08+-0.03 x 0.16 x 0.0128cm. The 0.315+-0.008cm thk hr steel plate is welded to beam for fixingseat & back frame. The powder coated (dft- 50+- 10 microns) welded leg ms structure is made from dia5.08+-0.03cm x 5.08+ 0.03 x 0.16 x 0.0128cm & dia5.08+-0.03cm x 2.45+-0.03 x 0.16 x 0.0128cm. The shoes are made of high impact strength polypropylene polymer compound with indoor grade uv resistence and assembled over the tubular frame. The armrest are made of high impact strength polypropylene polymer compound with indoor grade uv resistence and assembled over the tubular frame. The l-shape desklet is made of 1.8+-0.05 cm thk plb with 0.02+-0.05cm thk injected moulded pp all around . Desklet has front & back adj. Of 4.4+-0.5cm. Outer dimensions: - 31.5+-0.1cm (w) x 47.0+-0.1cm (d). 1.:- the paper tray is made up of dia 0.4+-0/0.005cm ms. Rod which is spot welded to fram a mesh – type structure. The powder coated (dft- 50+- 10 microns) size: - 40.1cm (w) x 36.1cm (d) x 22.0cm (h). It’s cover can be retro fitted on to seat & back. The seat cover is made of high abrasion resistence fabric with foam lamination & 2.5cm pu foam insert. The back cover is made of high abrasion resistence fabric with foam lamination & 0.1cm pu foam insert. As per Direction of Engineer in Charge

Supply installation & Placement of Wooden tall unit : Overall dimension (1980x500x 600)mm fabricated from 6,12,19mm TR BR BWR grade phenol bonded ply conforming to IS:303, with factory type finish, using low VOC adhesive for joinary work, all hardwares handles locks of Hattic /Hafele /Godrej, 2mm pvc edge binding on all exposed edges, out side finished by melamine finish 4mm veneer all round (ISI grade decorative) and Inside finished with 8mm balancing laminate, all laminates conforming to IS:4586. 75mm high skirting In all visible low surface. Unit consistent with 1 Nos Lockable 700mm high, 1 shutter). 1 Nos 3wt LED spot light to be provided for in side illimination as per instruction of Engineer in Charge.

Supply installation & Placement of work station with End Partition with 3 Drawer lockable mobile Metal Pedestal: Over all dimention of 1350 x1350x600x1200 mm Providing and placing of work station: worksurface desk shall be 1500 mm in both the direction from centre, 600 mm width and 750 mm height for each. {Size: (1350 x 1350) x 600 ) mm Each} The work top shall be made up of CNC processed minimum 25 mm thick prelaminated particle board(OSL) conforming to IS: 12823. The back side of main desk work top shall be glued with balancing laminate of minimum thickness 0.6 mm. The side edges of work top shall be lipped with minimum 1 mm thick edge banding. Gable end(where applicable) will be made of 25mm thick prelaminated particle bord(BSL) as per IS:12823 Edge banded with 2 mm edge band on exposed sides and 1 mm thick edge band on other sides fixed with hot melt glue. Providing & fixing Fixed type pedestal /drawer unit shall have outer dimensions of 375mm(W) x 500mm(D) X 715mm(H). The drawer unit shall consist of 2 box and one filing box. The drawer shall be mounted on double extension telescopic ball slides. It should freely slide in horizontal direction. The construction shall be welded assembled and shall have 0.8mm th CRCA body shell, drawer front & tray, stiffener, top and bottom. It should have central locking. It shall be finished with epoxy powder and shall be coated upto thickness of 50 microns (+/-10). The thickness of partition would be 50mm & height of the same would be 1200mm. Providing & Fixing 1230 mm height snap fitted Tile Based Partition System of overall 65mm thickness inner framework of CRCA steel of Grade D as per IS:513 covered with tiles on both sides and covered with aluminium powder coated trims on top and end sides. The vertical and horizontal channel frame made in CRCA sheet of 1.5mm to 0.8mm thicknes rigidly connected withpartition post. Partition has steel raceway at bottomlevel. The post cap, vertical and horizontal trim and end cap for channel shall be made of aluminium/PVC. Top tiles shall be 12mm thick prelaminated tiles or white marker laminated writing board or soft board covered by fabric tile or double screen glass panel finished with pressure sensitive self-adhesive texture film of approved texture pattern finish and Bottom tiles shall be 12mm thick prelaminated tiles. Snap fitted metal race way for n/w facia and on above /below the table top for power cutout. All CRCA and aluminium parts should be finished with Epoxy powder coating with Dry Film thickness 40-60 microns CRCA articles are pre finished with a 7 tank phosphate process for surface treatment before the powder coating. •Over closing Construction & Material Welded Assembled 0.8 thk CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener. 1.2 thk CRCA Top Stiffener & Bottom stiffener Drawer Fronts Metal Front Straight Edge Drawer Specification All Drawers with Double extension precision ball slide 390 wide Pedestals File drawer suitable for storing Fullscape files in Depth wise manner. A4 files in width wise manner In 585 deep units, 1 no of File hanger provided in File Drawer For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Knobs provided on drawer only for Elan free standing and Credenza Pedestal. Locking •10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism for ‘Box Box File’ Pedestal. Top Panel •Metal Straight Edge To pass as per the direction of Engineer-in- Charge Drawer Configuration /Product Size /styling Castor •Swivelling nonlockable Castors mounted below the body shell for Free Standing Full Height Mobile Pedestal and M8 Leveling stud for Free standing Pedestal. Antitipping •Fifth roller arrangement mounted below File drawer to avoid toppling of unit when file drawer is pulled out. Partition in Drawer: Partition in Box Drawers with lock mounted Application /Mounting Environment •Suitable for pushing below work surface which has got a clear height of 725 mm from As per Direction of Engineer in Charge.

Supply installation & Placement of Chair: made up of 1.2+-0.1cm thk hot pressed plywood measured as per qa method described in ocp-qlta-pl 14-18 & upholstered with pure leather and moulded hr polyurethane foam .the foam is designed with counter lumber support for extra comfort.it is moulded high resilence polyurethane foam of density =45+/- 2 kg/m3 and hardness load 16+-2 kgf as per is:7888 for 25% compression.the seat & back are arrested together with spine made up of 0.8cm+-0.05cm thk hr steel and is powder coated (dft 40-60 microns).the armrest assembly comprises of 3 parts viz. The armrest support tube & pu fonished armrest & the armrest top. It is made of 2.54+- 0.03cm x 0.16+-0.0128cm thk m.s.e.r.w. support tube and chrome plated. The ou armrest is made of black integral skin pu foam with 50-70 shore (a) hardness & reinforced with ms insert. The top is made up of abs & upholstered with foam & leather.the mechanism is designed with the following features: - • 360 deg revolving type. • seat back tilting ratio is 1:1.5. • front pivot for tilt with feet resting on ground ensuring more comfort. • tilt tension adjustment. • 5 position locking with anti shock back mechanism, which prevents the backrest from impacting the user when lock i realesed. • static seat depth adjustment = 5.0+-0.5cm with 5 position locking. It is designed with 360deg revolving type without back tilt. It has an adjustable stroke 0f 9.0+-0.3cm.it has an adjustable stroke 0f 12.0+- 0.3cm. The bellow is 1 piece and blow moulded in black pu. It is made up of die-cast aluminium with buffing finish .it is fitted with 5 nos twin wheel castors. The pedestal pitch center dia is 67.0 +- 0.5cm pitch center dia. (77.0+- 1.0cm with castors). 5 no twin wheel castors are injected moulded in black nylon. Back: (W) 53 cm x (H) 73 Cm, Seat : (W) 54.6 cm x (D) 49 cm Overall Dimensions of Chair Seat Height - min 43.4 to max 55.4 cm. Back Height - min 99.4 to 111.4 cm. Width & Depth of Chair as measured from pedestal - Width 77 cm and Depth 77 cm As per Direction of Engineer in Charge

Supply installation & Placement of Table: Over all dimensions is 1800Wx750Dx750H. : Table top is made of 25mm thk. MDF OSR board (Bottom side in white color) as per IS: 12406 which is having two finish options. Option 1: PU coated on top side with the color options as per color chart. Option 2 : Membrane on top side with the color options as per color chart. UNDER STRUCTURE: Legs are made by welding the combination of MS ERW round Tube 63.5 X 2mm THK as per IS:7138, flanges made CRCA sheet of 1.6mm thk. and1.2mm thk. as per IS 513, inside plates made of HR 5mm thk. sheet as per IS:2062. Assembly is epoxy polyester powder coated (Min 45 micron). Table top folds upside at offset center pivot provided on support bracket which is Aluminumalloy (ADC12) pressure die cast part coated with epoxy polyester powder coated(Min 45 micron). Table top connected with spring loaded mechanismwith pull handle made of MS ERW Ø16x1.2mm thk with an insert tube of $12.7x1.6mm thk tube as per IS:7138. Coated with epoxy polyester powder coated (Min 45 micron) to operate table top. Legs are provided with casters of Ø65mm lockable type for ease of movement and can be locked when required at any position. As per Direction of Engineer in Charge

Supply installation & Placement of Table with Wire manager 1 seater: Top Work surface: Top thickness 30.8 {18 ±0.5 mm + 12 ±0.5 mm OSR MDF IS 14587 + 04 mm Membrane on Top Surface {full top} and Bottom Face {on widthwise buttons} of Top Assy}. Edge profile Waterfall Edge 10mm radius on top edge and 5mm at bottom. LEGS: Made from 25 ±0.5mm PPB as per IS 3087 having a straight profile with half round edges and clad with 0.6mm thick Post Forming laminate. Overall thickness of leg is 26.2mm. Overall dimension 760 x 600 x 713 (HR) x 740mm along with wire management system. MODESTY PANEL: Made from Pre Laminated Twin boards of 18±0.5 mm thick as per IS 12823. WIRE CARRIER: Made from 0.6 ±0.09 mm thick powder coated 50microns (±10) MS CRCA sheet. COVER CARRIER: Made of 12 ± 0.5 mm MDFIS 12406. Painted all over. As per Direction of Engineer in Charge

Supply installation& Placement of Chair: The seat is made up of 1.4± 0.1 chick hot - press 4 plywood upholstered with fabric and moulded polyurethane foam. It has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a sliding mechanism. SEAT SIZE: 50.0cm (W)x 49.0cm(D).The Back is injection moulded in Glass filled Polyamide which is upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 6.0±0.1cm.BACKSIZE: 50.0cm(W) x68.0 cm(H).The polyurethane foam for seat is of density 55± 5kg/m3.The height adjustment armrest is made of Polyamide struture and polypropylene Housing with moulded PU armtop having a adjusted of 7.0+ 0.3 cm The inner tube of armrest is chrome plated. The mechanism is designed with the following features:• 360° revolving type.• Centre tilt Synchro• 3 position (including upright lock) giving option of variable tilt angle to the chair with anti shock feature. The pneumatic height adjustment has an adjustment stroke of 8.5+ ± 0.3cm.The pedestal is injection moulded polymide and fifted with 5 nos. twin wheel castors. The pedestal is 66.0+ 0.1cm wheel Diameter. The twin wheel castors are injection moulded in black Glass filled polyamide having 6.0±0.1cm wheel Diameter. The powder coated frame is made of Día2.8±0.03cm x0.2±0.02 cm the M.S. Round tube. The frame is fitted with plastic caps made of injection moulded glass filled Polypropylene.FullBack- 75(W)* 75(D)* 100-109(H)* 45-54 (SH). As per Direction of Engineer in Charge

Supply installation & Placement of Sofa With Seat Slide facility: Total length 870 b). Total width 960 c). Total height 960 d seating area width 460 e). Seating area length 480 f). Seating area height from ground 400 g). Arm height 630 h). Arm length 410 i). Back height from arm 180 j). Back width 350 k). Arm width 290 l). Leg height 35 m). Length between legs 645 n). Width between legs 520 thread : polyester poly pitch :- 3-4 mm thickness (mm) : 0.8-1.6 mm thick weight (gsm) : 450-600. Frame material (tropical wood / pine wood/ rubber wood): moisture content ( recommended 10 – 18 %) : 10-18% anti – tremite treatment (recommended borex powder treatment) : borex powder treatment kiln drying : thickness of plywood used(m(rme)c :o 1m2e,n1d8emdm t &hi c2k.2nmesms (1m2d –f 1)8 mm) :12,18mm & 2.2mm mdf provide weight of recron filling used per seat* density (kg/m3): s.s. foam & 32 dencity type of foam (virgin/composite/moulded/ slabstock) : virgin foam * provide weight of recron filling used per seat* thickness (mm) : 10 mm hard density (kg/m3): 28 dencity type of foam (virgin/composite/moulded/ slabstock) : virgin foam * provide weight of recron filling used per seat* density (kg/m3): 32 dencity * please provide layerwsie detail of foam used along with details of density & thickness* width of belt (mm) : 50.8 mm & 76.2 mm total length of belt used (mm): tensile strength (kg/cm) : n/a. * provide details of total length of wed & width of web used *spring details ( s-spring / pocket spring): n/a. Thickness of s-spring (mm) : n/a. Number of springs used: n/a. Length of s-spring used (mm) : n/a. Number of pocket springs per seat: n/a. Thickness of pocket spring (mm) : n/a. * provide details of number of springs & pitch * * type of glue used : (synthetic / rubber base/ water base/ solvent base): rubber base (s.b.s) * material handling data sheet (msds) for glue * size of pin : (zinc plated) yes * no. Of pins : 80/12,90/35 & 100/50 As per Direction of Engineer in Charge

Supply installation & Placement of chair With Seat Slide facility: The seat is made up of 1.2 +- 0.1 cm thk hot pressed plywood measured as per aq method described in ocp-qlta-pl14-18, upholstered with synthetic leather over moulded hr resilence pu foam.moulded high resilence polyurethane foam of density =45+/- 2 kg/m3 and hardness load 16+-2 as per is: 7888 for 25% compression.the mechanism is designed with the following features:- • up & down adj – 8 steps. Hgt adjustment armrest structure which is chrome plated & fitted with an armrest top . Fixed armrest top is pu moulded over metal insert. The mechanism is designed with the following features:-• 360 deg revolving type. • single pont control. • front pivot for tilt with feet resting on ground ensuring more comfort. • tilt tension adjustment. • 4-position locking and anti-shock feature. • Overall Dimention 76.1 x 76.1 x (114-128.2 V ) x (44-68.2 V)cms, seat/back tilting ratio of 1:2. Back can be adjusted in 5 position bu manually. Stroke of hgt adjustable spine is 7 cm .stroke of hgt adjustabilityis applicable for high back & mid back chair. It has an adjustable stroke of 10.0+-0.3cm. It is a high prssure die cast polished alu. & fitted with 5 nos. Twin wheel castors.the pedestal is 65.0+-0.5cm. Pitch center dia. (75.0+-1.0cm. With castors). The twin wheel castors are injected moulded in black pp. The powder coated welded tubular frame is made up of dia 2.54+-0.02cm x 0.16thk m.s.e.r.w tube with a connecting ms spine welded to it. Back spine is fitted to the frame assembly. As per Direction of Engineer in Charge

Supply installation & Placement of sofa: Handrests are from 304 SS round tapered sections covered with high density self skin pu foam to prevent cold shock. Overall dimention 181 x 80.5 x 75.5 Cms seat shell made up of high density self skin pu foam reinforced with 3mm msperphorated sheet insert. The pu foam is having density of 520+-10kg/m3. With a shore (a) hardness of 55+-5. It is made up of high density self skin pu foam reinforced with 3mm msperphorated sheet insert. The pu foam is having density of 520+-10kg/m3. With a shore (a) hardness of 55+-5. It is made up of black coated powder ms.erw sq. Tube of size 6.0+-0.05cm x 0.18+-0.016cm thk fitted with polypropelene endcaps. It is made up of black coated powder high pressure alu. Die cast leg are fitted with soft grip pvc level adjusting shoes. As per Direction of Engineer in Charge

Supply installation & Placement of Table : Comprises of Main Desk , ERU and Pedestal: MAIN TOP: MDF + VENEER + PU Coating, Size : 3600 W * 1080 D * 750 H, TOP THICKNESS – 90 mm. MOBILE PEDESTAL: MDF + Veneer + PU Coating, Size : 480 W X 640 D X600 H mmConstruction & materials:- assembled. 18mm MDF Veneer top & drawer front. 18mm MDF venner, stiffners. 0.5 mm thk crca for drawer side –buttom –side & drawer back. Crca (d) grade as per is-513. Drawer front:- metal front straight edge. 18mm thk wooden front post formed. 18mm thk wooden plb front full straight edge / pvc lipping on all edges. Drawer specifications:- all drawers are double extension precision ball slide. 390 wide pedestal file drawer – suitable for storing fullcase file in depth wise manner . A4 file in width wise manner. 450 wide pedestal file drawer – suitable for storing fullscape ezee & visa file in depth wise manner . A4 file in width wise manner. 2 nos. Of file hanger provided in a file drawer. File drawer provided with fifth roller arrangements. For drawer pulling sidewise tappered recess is provided in shell behind the drawer front. Locking:- 10 cam lock & cental lock rh locking with actuator & locking chnnel mechanism for box-file pedestals. 10 cam lock with indiviual rh locking for 3 big box) pedestal. Top panel:- 8mm thk metal straight edge top. 18mm thckness wooden top post form . 18mm thckness wooden top post form/ pvc lipping on 3 edge. Leveler & castor:- swiveling non lockable castor mounted below the body shell. Portion in drawers:- optional accessory for box drawer. Plastic pencil tray:- optional accessory. Application/ mounting environment:- suitable for pushing below wok surface which has got a height of 725mm from below. Finish:- epoxy polyester powder coated to the thickness of 50 microns(+-10. ERU TOP: MDF + VENEER + PU Coating, Size : 1900 W X 480D X 550 (Not From Ground with Castors), TOP THICKNESS - 25 mm. As per Direction of Engineer in Charge

Golden Portoro wall panel in color of choice fixed on available brick wall surface including delivery lifting, installation and fitting fixing by standard method of 15-18mm thick stone slab, minimum base cost of material Rs. 850- 950 per squarefeet As per Direction of Engineer in Charge

Supply installation and placement of Sofa Total Length a) Total Length 1420 b) Total Width 960 c) Total Height 960 d) Seating Area Width 460 e) Seating Area Length 950 f) Seating Area Height from Ground 400 g) Arm Height 630 h) Arm Length 410 i) Back Height from Arm 180 j) Back Width 350 k) arm Width 290 l) Leg Height 35 m) Length between Legs 645 n) Width between Legs 520 THREAD : Polyester Poly PITCH :- 3-4 MM Thickness (mm) : 0.8-1.6 MM THICK Weight (GSM) : 450-600 FRAME MATERIAL (TROPICAL WOOD / PINE WOOD/ RUBBER WOOD): Moisture Content ( Recommended 10 – 18 %) : 10-18% Anti – Tremite Treatment (Recommended Borex Powder Treatment) : Borex Powder Treatment Kiln Drying : Thickness of Plywood used(Rmemco)m : e1n2d,1e8dM TMh i&ck 2n.e2sMs M1 2( M– D1F8) mm) :12,18MM & 2.2MM MDF * Provide weight of recron filling used per seat* Density (Kg/m3): S.S. Foam & 32 Dencity Type of Foam (Virgin/Composite/Moulded/ Slabstock) : Virgin Foam * Provide weight of recron filling used per seat* Thickness (mm) : 10 MM HARD Density (Kg/m3): 28 Dencity Type of Foam (Virgin/Composite/Moulded/ Slabstock) : Virgin Foam * Provide weight of recron filling used per seat* Density (Kg/m3): 32 Dencity * Please provide layerwsie detail of foam used along with details of density & thickness* Width of belt (mm) : 50.8 MM & 76.2 MM Total length of belt used (mm): Tensile Strength (Kg/cm) : N/A. * Provide details of total length of wed & width of web used *SPRING DETAILS ( S-SPRING / POCKET SPRING): N/A. Thickness of S-Spring (mm) : N/A. Number of Springs used: N/A. Length of S-Spring used (mm) : N/A. Number of Pocket springs per seat: N/A. Thickness of Pocket Spring (mm) : N/A. * Provide details of number of springs & Pitch * * Type of Glue used : (Synthetic / Rubber base/ Water base/ Solvent Base): RUBBER BASE (S.B.S) * Material Handling Data Sheet (MSDS) for Glue * Size of Pin : (Zinc Plated) Yes * No. Of Pins : 80/12,90/35 & 100/50. As per Direction of Engineer in Charge

Supply installation & Placement of Table: Dimantions 600mm(w)*1000mm (l)*428mm (h)* 8mm(glass thk). Material =Glass of 08mm thk tempered,solid rubber wood legs & frame , intermidiate shelf MS poweder coated with floral perforated pattern sheet as bottom shaf . Decoration materials- PU coateing to rubber wood parts clear glass As per Direction of Engineer in Charge

Supply installation & Placement of File Storage cum decorative Display Cabinet: MDF + veneer + pu coating & glass. Overall size- 1000x480x 2035mm not from ground with castors. Top thickness- 25mm. As per Direction of Engineer in Charge

Supply ,Fitting & Fixing of Sofa and as per approved drawing & design / specification. NOMENCLATURE & DIMENSIONS (mm):- :Total Length – 1990 Total Height - 935 Total Width - 885 STITCHING Seat 485:( type of thread : Nylon , Polyester) PITCH: 4 ( Pitch of thread i.e. Stitch per inch) LEATHER/PVC/FABRIC: (PU/PVC /Cotton/ Polyester/ Composite) PU Thickness (mm) : 1.0mm Weight (GSM) : Tensile Strength wrap/weft (Kg/cm) : Bursting Strength (Kg/cm2) : Adhesion (PVC/PU Backing) (Kg/cm) : Colour Fastness to Rubbing {Dry /Wet} (Scale 1-5) : FRAME MATERIAL (TROPICAL WOOD): Tropical wood Moisture Content ( 10 – 12 %) : 8%---12% Anti – Tremite Treatment (Borex Powder Treatment) : Kiln Drying :Thickness of Plywood used(mm) :7.5-15 Standard of Plywood used: Required Standard : IS 303 Commercial Plywood} Provide weight of recron filling used per seat SEAT FOAM: (DENSITY, TYPE) Thickness (mm) :30mm Density (Kg/m3):40# density hard Type of Foam (Virgin/Composite/Moulded/ Slabstock) : Upholestered in pure leather of cappuchino matt finish. Virgin Please provide layerwsie detail of foam used along with details of density & thickness Provide weight of recron filling used per seat BACK FOAM: (DENSITY, TYPE) Thickness (mm) :50mm+30mm Density (Kg/m3): 28#density medium -soft , 30# density medium-soft Type of Foam (Virgin/Composite/Moulded/ Slabstock) : Virgin Please provide layerwsie detail of foam used along with details of density & thickness ARMREST FOAM: (DENSITY, TYPE) Thickness (mm) :10mm Density(Kg/m3):27# density hard Type of Foam (Virgin/Composite/Moulded/ Slabstock) : Virgin Please provide layerwsie detail of foam used along with details of density & thickness BELT/ WEBBING MATERIAL:Width of belt (mm) :40mm Total length of belt used (mm):520 Tensile Strength (Kg/cm) : Provide details of total length of wed & width of web used SPRING DETAILS ( S-SPRING / POCKET SPRING): Thickness of S-Spring (mm) :3.5mm Number of Springs used:4 Length of S-Spring used (mm) :510 Number of Pocket springs per seat:126 Thickness of Pocket Spring (mm) :80 Provide details of number of springs & Pitch LEG MATERIAL: Fixing of Leg : (Self Tapping Screw / Insert with metric threading) Self Tapping Screw Material of leg : (Plastic / Insert Moulding / Wooden/ MS / SS) Wooden Bush for Leg bottom : (PVC bush / Felt Pad) PVC bush, Type of Glue used : (Synthetic / Rubber base/ Water base/ Solvent Base) Synthetic As per Direction of Engineer in Charge

Supply and Placement of Table- with 2Nos. Lockable 3 Drawer metal pedestal and 2Nos wooden ERU 1050x460x759 mm with locked storage: Reception Tables combining the elegance of Wood, Metal and Glass with tops in rubberwood Impression Clean matt PU finish 18mm thick Inside radius - 700.0 mm Outside radius – 1350.0 mm Depth – 650 mm Cork Rubberized cork – 18mm thick Glass Frosted Glass 10mm thick Diamond cut finishing on edges Inside Radius – 1202.5mm Outside radius – 1402.5mm Depth – 200mm *Note: Angle sustained within arc surface is 60 deg. Under structure Modesty Panel MS Perforated sheet. Below Work surface : 0.8 mm (thick) x 665.0 mm (height) x 1345.0 mm (flat length) Above Work surface : 0.8mm (Thick) x 260 mm (height) x 1345.0 mm (flat length) Legs MS tube 1.6 mm thick .Diameter 50.8 mm Height 604 mm. 2 Nos. Credenza: Fabricated from boarer resistant, termite resistant, phenol bonded 19,12,6 mm ply conforming to IS303, 1mm ISI grade Laminate, French polished teak wood beat, Hettic/Haffele/ Godrej hardware, SS hinge, hardware, 2mm PVC lipping pasted in all exposed edges overall dimension of 17sft as per direction of the Engineer in charge

Supply installation & Placement of Table 1 Seater- Over all dimension 675 x 600 x 750mm Top work surface: all tops are made from 25 ± 0.5 mm thick prelaminate particle board (PLB) as per 15•12823 edge duly sealed with 2mm thick pvc beading. Understructure: legs are made from 18 ± 0.5 mm thick prelaminate twin board (PLT) as per 15-12823, having a curved profile with 0.8 mm thick pvc lipping of matching colour. Modesty panel: made from pre laminated twin boards of 18±o.5 mm thick as per is 12853 in two shades. Wire carrier: made from 1.0 ±0.1 mm thick powder coated 50 microns (±10) ms crca sheet, running along the width of desk fitted on the modesty panel from inside.As per Direction of Engineer in Charge

Supply installation & Placement of Table: Main Desk 1500 X 750 X 740, ERU 1050 X 450 X 705)mm top and side panel 25 mm thick plain particle board (ppb) clad with 0.6mm thick post formed laminate and 1mm thick backing laminate (bdl). Flat edge duly sealed with 2mm thick pvc beading. Modesty: 18mm thick plain particle board (ppb) clad with 1.0mm thick decorative laminate (dl) on both sides. Edge sealed with 2mm thick pvc beading. Extended return unit (eru): top and side panel: 25 mm thick plain particle board (ppb) clad with 0.6mm thick post formed laminate and 1mm thick backing laminate (bdl). Flat edge duly sealed with 2mm thick pvc beading. Modesty: 18mm thick plain particle board (ppb) clad with 1.0mm thick decorative laminate (dl) on both sides. Edge sealed with 2mm thick pvc beading. Hinge door unit (hru): top and side panel: 25 mm thick plain particle board (ppb) clad with 0.6mm thick post formed laminate and 1mm thick backing laminate (bdl). Flat edge duly sealed with 2mm thick pvc beading. Doors, partitions, shelves: 18mm thick plain particle board (ppb) clad with 1.0mm thick decorative laminate (dl) on both sides. Edge sealed with 2mm thick pvc beading. Drawer configuration /product size/ styling:- box-box-file - 300mm (w) x 435mm (d) x 646mm (h). Box-box-file - 390mm (w) x585/ 435mm (d) x 646mm (h). Box-box-file - 450mm (w) x435mm (d) x 646mm (h). Box - 390mm (w) x 585/435mm (d) x 646mm (h). Overclosing :- add 5mm for metal & wood straight edge top. Add 12mm for wood full radius top. Add 2mm for wood straight edge & full radius top. ##- including leveler / castors . Drawer inside clear space for 390mm (w) x 585mm (d) pedestal. Drawer box- 315mm (w) x 530mm (d) x 98mm (h). File drawer - 315mm (w) x 530mm (d) x 247mm (h). Drawer inside clear space for 390mm (w) x 435mm (d) pedestal. Drawer box- 315mm (w) x 380mm (d) x 98mm (h). File drawer - 315mm (w) x 380mm (d) x 247mm (h). Drawer inside clear space for 450mm (w) x 435mm (d) pedestal. Drawer box- 375mm (w) x 380mm (d) x 98mm (h). File drawer -As per Direction of Engineer in Charge

Supply installation & Placement of Storage with Glass Covered Display Rack : Top & Bottom Panel: Overall Dimension 790 x 400 x 2200mm Made of 25mm thick (±1mm) Particle Board clad with decorative Post formed laminate on top side & balancing laminate on bottom side. Post forming edge at the front side. Other Panel: Made of 18mm Thick (±1mm) Pre-lam Particle Board. Upper Glass Door: Made of 5 mm black tinted glasses. Handles: Metal handles are provided on the shutter door at 128mm CD. As per Direction of Engineer in Charge

Supply installation & Placement of Chair: The seat & back is made up of 1.2 +- 0.1 cm thk hot pressed plywood measured as per aq method described in ocp-qlta-pl14-18, Over all dimension Back: (W)49.0 cm x (H)71.0 Cm, Seat : (W)49.0cm x (D) 44.0cm Overall Dimensions of Chair Seat Height - min 42.4 to max 53.4cm. Height - min102.4 to max 113.4cm. Width & Depth of Chair as measured from pedestal - Width-70.0 cm and Depth-70.0 cm.upholstered with fabric & moulded pu foam with pvc lipping all around. The back foam is designed with countered lumbur support for extra comfort. It is moulded high resilence polyurethane foam of density =45+/- 2 kg/m3 and hardness load 16+-2 as per is: 7888 for 25% compress-ion. The armrest top are injection moulded black pp.they are fitted to tabular armrest support made up of dia- 2.54+-0.03cm x 0.16+-0.0128cm thk ms erw tube & black powder coated (dft 40-60 microns). The tabular armrest support hold together the seat & back. The mechanism is designed with the following features:- 360 deg revolving type. 17 deg +-2 deg max tilt on pivot on center. Upright position locking. Tilt tension adjustment. The tabular frame is cantilever type & mad up of dia 2.54 +-0.03cm x 0.2+-0.016cm thk ms erw tube & black powder coated (dft 40-60 microns). It has an adjustable stroke of 12.0+-0.3cm.the bellow is 3 piece telescopic type & injection moulded in black polypropylene. It is fabricated from 0.2+-0.02cm thk hr steel (is:dd 1079/hr) powder coated (dft- 40-60 microns) & fittedwith an injection moulded in black pp hub cap with 5 nos. Twin wheel castors.the pedestal is of dia 60.0+-0.5cm . Pitch center dia. (70.0+-1.0cm. With castors). The twin wheel are injected moulded in black nylon. As per Direction of Engineer in Charge

Supply installation & Placement of Storage : Construction & materials:- construction is a knockdown construction of 25mm thk and 18mm thk plb with metal cladding of 0.8mm thk crca (as per is:513) from outside. Side metal cladding is coated with epoxy polyster powder of 50+-10 microns thkness. Top options:- in case of 2.5’ (h)storage unit, wooden top is provided which is made of 25mm thk plb whereas 4.0’ and 4.5’ (h) storage unit are provided with 11mm thk bent metal tops made of 0.8mm thk crca (as per is:513) from outside . The metal tops are coated with epoxy polyster powder of 50+-10 microns thkness. Door & openng door: - single door opening two door opening for all other width option 1200). The doors are made of 18mm thk plb with decorative laminate on one side and backing laminate on the other side. Shelving:- height wise adjustable shelf mounting holes provided on side panel for easy interchange of shelf height as required. Fixed shelf along with adjustable shelf provided only in case of 4.0 ‘and 4.5’ hgt units. No fixed shelves for750mm height storage units. 1 no. Adjustable shelf for 2.5’ / 4.0; / 4.5’ hgt and 1 no. Fixed shelf for 4.0’/4.5’ hgt without vertical partition for1190 w. Whereas 2 nos. Adjustable shelves for 2.5’, 4.0 ‘ and 4.5’ hgt and 2 nos. Fixed shelves for 4.0 ‘and 4.5’ hgt with vertical partition in between for 950w & above. A4 size box files(85x345x285 wxhxd) can be stored vertically. Uniformly disturbed load capacity for each shelf is 40kg max. Skirting option:- the skirting units are provided with 150mm high skirting made of 0.8mm thk crca (as per is:513) and are coated with epoxy polyster powder of 50+-10 microns thkness. Leveller:- screw type adjustable leveler with plastic base provides vertical adjustment of floor unevenness and levelling of units . Back panel:- back panel is made of 18mm plb with option of decorative laminates as well as fabric finish .2.5’ (h) units consists of single back panel where as 4.0’(w) & 4.5’(h) units consists of split top back panel and split back buttom panel separated by an alu. Extrusion. Locking mechanism:- 3 way nickel plated wooden furniture lock is provided for effective and positive locking of doors. Handle:- aesthetically appealing recessed handles of alu. Extrusion are provided for easy opening & closing. As per Direction of Engineer in Charge

Supply installation & placement of pedestal . Drawer box- 225mm (w) x 380mm (d) x 98mm (h). File drawer - 225mm (w) x 380mm (d) x 247mm (h). Construction & materials:- welded assembled. 0.6 mm thk crca for metal top & drawer front. 0.8 mm thk crca for body shell , side stiffners, & bottom. 1.2 mm thk crca for top & bottom stiffners. 0.5 mm thk crca for drawer side –buttom –side & drawer back. Crca (d) grade as per is-513. Drawer front:- metal front straight edge. 18mm thk wooden front post formed. 18mm thk wooden plb front full straight edge / pvc lipping on all edges. Drawer specifications:- all drawers are double extension precision ball slide. 390 wide pedestal file drawer – suitable for storing fullcase file in depth wise manner . A4 file in width wise manner. 450 wide pedestal file drawer – suitable for storing fullcase file in depth wise manner . A4 file in width wise manner. 2 nos. Of file hanger provided in a file drawer. File drawer provided with fifth roller arrangements. For drawer pulling sidewise tappered recess is provided in shell behind the drawer front. Locking:- 10 cam lock & cental lock rh locking with actuator & locking chnnel mechanism for box–box-file pedestals. 10 cam lock with indiviual rh locking for (3 big box) . Top panel:- 8mm thk metal straight edge top. 18mm thckness wooden top post form . 18mm thckness wooden top post form/ pvc lipping on 3 edge. Leveler & castor:- swiveling non lockable castor mounted below the body shell. Portion in drawers:- optional accessory for box drawer. Plastic pencil tray:- optional accessory. Application/ mounting environment:- suitable for pushing below wok surface which has got a height of 725mm from below. Finish:- epoxy polyester powder coated to the thickness of 50 microns(+-10 As per Direction of Engineer in Charge

Supply installation & Placement of chair : The seat is made up of 1.4± 0.1 chick hot - press 4 plywood upholstered with fabric and moulded polyurethane foam. It has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a slidingmechanism. SEAT SIZE: 50.0cm (W)x 49.0cm(D).The Back is injection moulded in Glass filled Polyamide which is upholstered with Mesh fabric..BACKSIZE: 50.0cm(W) x68.0 cm(H).The polyurethane foam for seat is of density 55± 5kg/m3.The armrest is made of Polyamide strture and polypropylene Housing with moulded PU armtop& Fixed. The inner tube of armrest is chrome plated. Full Back-65(W)* 58.5(D)*97.5(H)* 42.5(SH). All understructure of 304 SS As per Direction of Engineer in Charge

Glass Partition Providing and fixing of full height partition with double screen Toughened Glass tiles partition , Door & built in venetian Horizontal Blinds- Providing & Fixing of 80mm series Double screen full height partition system having framework of aluminium extrusions conforming to AISI-6063 covered with snap fitted tiles on both sides. Partition system provides Toughened Glass Tiles. All metallic parts undergo a 7 stage antirust treatment and are powder coated in matt finish to a thickness of 40-60 microns. The modular partitions are independent and grouted in the floors. The modular partitions are an assembly of the following parts:- FRAME - Frame forms the basic support structure for all other compone nts. The Top & Bottom aluminium profile will consist of 3 section having overall dimentions of 56.4mm x 40mm , 77.8mm x 26.9mm and 41.2mm x 11.4mm All Verticle and Horizontal aluminium profile will have overall dimentions of 77.8mm x 18mm and will be joined to each other by aluminium Angles. Aluminium cap profile having overall dimentions of 18mm x 13.4mm will be snap fitted on all verticle and horizontal members from both sides to hold panels. POST - The frames are connected at the junctions by aluminium connect- ors/posts.All "L" Shape corner post will be provide with Aluminium profile having overall dimentions of 80mm x 80mm in semi circular shape to get round shape at the corners. All 3 Way corner post will be provide with Aluminium profile having overall dimensions of 80mm x 80mm in square shape. TILES - The partition tiles shall be provided in 5mm thick Toughned Glass on both sides of the partition to create a hollow area for fixing built in venetian blinds for Holding section will be fixed with special plastic caps Door: 12mm thick Toughened Glass Door covered by frosted film of 3M make with patch fittings and floor Spring will be fixed with special type aluminium section with the glass partion. . Horizontal Blinds: Glass covering high-grade Aluminium Venetian Blinds with latest modern styles and trendy colours as per choice of architect/Engineer in charge. These horizontal slat blinds for both the outside or inside mount option will be of 20-25mm width and provide many practical benefits and are a great addition tothe office space. provide in Aluminium outer frame and all grids eherever glazing is provide. Heavy duty Aluminium angles will be provided at all corners of outer Frame. As per Direction of Engineer in Charge

Supply installation & Placement of Table : JOINING TOP: Table Top Panel: Made of 25mm Thick (±1mm) MDF Board with 2 side PU painted finish & hardness 2H. Leg: Made of metal tubes. Overall dimension 1200 X 1050 X 750 As per Direction of Engineer in Charge

Supply installation & Placement of chair : Back: (W)50.0 cm x (H)72.0 Cm, Seat : (W)50.0cm x (D) 46.5 cm Overall Dimensions of Chair Seat Height - min 44.2 to max 54.2cm. Height - min103.3 to max 115.3cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm. The seat/back shall be made up of 1.2 ±0.1cm thick hot pressed plywood measured as per QA method desaribed in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with moulded seat and back covers. The back foam shall be designed with contoured lumbar support for extra comfort. The dimensions of back shall be-50.0 cm (W) x 72.0 cm (H) and of seat shall be-50.0 cm (W) x 46.5cm. (D). The HR Polyurethane foamshall be moulded with density 45±2kg/m3-and Hardness load 16 ±2 kgf as.per IS:.7888-for 25% compression. The seat cover shall be injection moulded in black co-polymer polypropylene and back cover is vacuum formed from ABS sheets. The one-piece armrests shall be made of black integral skin polyurethane with 50-70 Shore 'A' Hardness and reinforced with M.S. insert. The armrests shall be scratch and weather resistant. The armrests shall be fitted to the seat with seat/armrest connecting strip assembly made of 0.5 ±0.05-cm. thick HR steel.The center tilt mechanism shall be designed as-360° revolving type, 17° ±2° maximum tilt on pivot at center, Upright position locking, Tilt tension adjustment. The pneumatic height adjustment shall have an adjustment stroke of 12.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel castors. The pedestal shall be 66.3 ±0.5cm.(76.3±1.0 cm with castors). The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 44.2 to max 54.2cm, Height - min103.3 to max 115.3cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm. As per Direction of Engineer in Charge

Supply installation & Placement of Chair: The seat is made up of 1.4± 0.1 chick hot - press 4 plywood upholstered with fabric and moulded polyurethane foam. It has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a sliding mechanism. SEAT SIZE: 50.0cm (W)x 49.0cm(D).The Back is injection moulded in Glass filled Polyamide which is upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 6.0±0.1cm. BACKSIZE: 50.0cm(W) x68.0 cm(H).The polyurethane foam for seat is of density 55± 5kg/m3. It is made of glass filled Polyamidearm structure with PU arm top and height adjustment of 7.0 ±0.5cm.The arm top has swivel and To-For movements. To-for movement is 6.0± 0.5cm.The inner tube of armrest is chrome plated. The mechanismis designed with the following features :• 360° revolving type.• Centre tilt Synchro• 3 position (including upright lock) giving option of variable tilt angle to the chair with anti shock feature. The pneumatic height adjustment is chrome plated with an adjustment stroke of 9.0 ± 0.3cm.The pedestal is High Pressure Die cast polished Aluminumand fitted with 5 nos. twin wheel castors. The pedestal is 65.0±0.5 cm P.C.D. The twin wheel castors are injection moulded in black Glass filled polyamide having 6.0±0.1cm wheel Diameter. The Chrome plated tubular frame is made of Día2.8±0.03cm x0.2±0.02 cm the M.S. Round tube. The frame is fitted with plastic caps made of injection moulded glass filled Polypropylene. Full Back-75(W)* 75(D)* 100-109(H)* 44.5-53.5(SH). As per Direction of Engineer in Charge

Supply installation & Placement of File Storage (metal)Overall Dimensions of VSDU - VSDU 7 size in 1830(H) X900(W) X450(D). Construction and Metal: Rigid knock down construction. Back, sides and door are made from 07.mm (+ 0.07mm) high yield strength CRCA, rest in 0.8mm (+ 0.08mm) CRCA. Sliding Door Arrangement: Sliding door with top hanging arrangement to prevent derailment. Each door provided with 2 Plastic roller having steel ball bearing for smooth movement of door & less noise. Locking & Handle: Snap on type aesthetically appealing die cast 5 Lever Cam lock for safe locking. Plastic flush & recessed handle. Shelving: Height wise Adjustable shelf mounting. Uniformly distributed load capacity of the shelf i 40 kg maximum. VSDU 7- 4 Nos. Of Adjustable half shelves. VSDU 7- A4 size box file (85Wx345HX285D) can be stored vertically on four shelves and clear space above fifth shelf is 220mm. As per Direction of Engineer in Charge

Supply installation & Placement of table: Top:- all the tops are made of 25 mm thk plb tops with 2mm pvc edge beading. Under structure:- leg tube:- made of ms erw . Tube connecting the top support and base. Top support:- made from ms (u) bracket (3 nos) welded to 63.5mm dia x 1.6mm thk ms erw tube. This is fixed on the top the leg tube using m8 bolt. The top support is to fixed the wooden top using self tapping screws finish : poeder coated (avg. Thk 40 microns) base:- made from ms erw tube formed 1 end & welded at other with ms erw tube this is fixed on the buttom the leg tube using m8 bolt. Level adjustment facility has been provided. Finish : chromium (thk -0.2-0.5 microns) over nickel platting (thk -10-15 microns) modesty:- this panel are presently used in models- v1&v2 it is fitted between the leg tube and the top using kd fittings. For v2: plb with matching pvc lipping of 1mm thk along wdges. Overall dimension 1500 x 894 x 750mm As per Direction of Engineer in Charge

Supply installation & Placement of - TABLE TOP: The panel is made from 25 ±0.5 mm THK Pre Laminated Boards as per IS-12823 with 2 mm Thick PVC beading on all sides. SIDE PANEL: The panel is made from 25 ±0.5 mm THK Pre Laminated Boards as per IS-12823 with 2 mm Thick PVC beading on user sides and 0.8 mm on Top & Bottom side. The side panels have 2 glide screws each for leveling of the desk. MODESTY PANEL: The panel is made from 18 ±0.5 mm THK Pre Laminated Boards as per IS-12823 with 0.8 mm Thick PVC beading on all edges. FREE STANDING PEDESTAL: The free standing pedestal is made from 18 ±0.5 mm THK Pre Laminated Boards as per IS- 12823 with combination of 2mm & 0.8 mm Thick PVC beading on all exposed surfaces as per requirement. The drawers are provided with suitable slides for smooth operation. All pedestal drawers are centrally locked with single key. As per Direction of Engineer in Charge

Supply installation & Placement of Display Panel with bottom storage: Back panel is made of 25mm thick one side raw medium density fibre board interior grade conforming to IS:12823 with 1mm thick white board laminate on back side. All the edges of the panel are provided with machine pressed 2mm thick PVC lipping. SUPPORT LEGS: Support legs are made from 10.0 mm thick H.R steel as per IS: 2062 and are fixed on to the wooden back panel at bottom on both sides.The legs are coated with min. 45 micron thickness of epoxy polyester powder. CASTORS: Lockable castors (4nos.) are provided at the bottom of support legs so that the user can simply wheel the marker screen to different locations. Product Specification. Product : storage is a knock down assembly comprising of storage top panel, side panels, bottom panel and door panels. All the panels are made of 18mm thick pre-laminated board interior grade of approved shade conforming to IS:12823. (1800x 1200 x 550)mm All the edges of the panels are provided with machine pressed 2mm thick PVC lipping. Door opening and closing is made convenient by incorporating Push to open mechanism for easy opening and closing. T.V MOUNTING BRACKET: T.V bracket consists of 2 brackets STORAGE: All the panels are made of 18mm thick pre-laminated board interior grade of approved shade conforming to IS:12823. All the edges of the panels are provided with machine pressed 2mm thick PVC lipping. Door opening and closing is made convenient by incorporating Push to open mechanism for easy opening and closing. T.V MOUNTING BRACKET: T.V bracket consists of 2 brackets: 1) T.V back bracket. 2) T.V hook. Both T.V back bracket and hook are made from 1.6mm thick C.R.C.A as per IS:513 and coated with min.45 microns of Epoxy Polyester powder. T.V mounting bracket is designed to hold following T.V sizes: MINIMUM - 32" MAXIMUM - 42" MARKER HOLDER: Marker Holder is made from 2mm thick C.R.C.A as per IS: 513 and is fixed on to the wooden white board panel on one side with the help of both side adhesive tape.It is coated with min. 45 micron thickness of epoxy polyester powder. WIRE MANAGEMENT COVERS: Wire management consists of 2 covers made from 1.6mm thick and 2.0mm thick C.R.C.A as per IS:513 and are coated with min.45 microns of Epoxy Polyster powder. ELECTRICAL FITTING: 8-module Spike guard (4-switch & 4-universal socket) is provided in the storage area for Electrical input to the T.V mounted on the mobile media panel. As per Direction of Engineer in Charge

Supply installation & Placement of Chair: The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed moulded reconstituted wood & upholstered with leather and moulded polyurethane foam. Size of back shall be (W)-46.0cm, (H)-57.0cm & size of seat shall be (W)-49.0cm x (D)-49.5cm. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The back rest should be connected to the mechanism with a drop-lift mechanism which can be adjusted in the range of 7.0+/-0.5cm for the comfortable back support to suitable individual need. Armrests should be pressure die casted in polished aluminium with PP arm tops. The mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:3, Synchronized tilt, Back tilt with 4 position locking and Side tilt tension adjustment knob should be operated while taking back support for better adjustment of comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of head rest shall be (W)26.0cm x 12.0cm(L). The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 113.5 to max 138.0 cms. Seat height - min 41.0cm to max 51.0 cm. Dimensions tolerance / variations shall be within +/- 1 cm. 12.0cm(L) Back: (W) 46.0 cm x (H)57.0 Cm, Seat : (W)49.0 cm x (D) 49.5 cm Overall Dimensions of Chair Seat Height - min 41.0 to max 51.0 cm. Height - min 113.5 to max 138.0 cm. Width & Depth of Chair as measured from pedestal - Width-75.0 cm and Depth-75.0 cm As per Direction of Engineer in Charge

Supply installation & Placement of Chair: The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed moulded reconstituted The seat/back shall be made up of 1.2 ±0.1cm thick hot pressed plywood measured as per QA method desaribed in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with moulded seat and back covers. The back foam shall be designed with contoured lumbar support for extra comfort. The dimensions of back shall be-(W)50.0 cm x (H)49.0 Cm and of seat shall be-50.0 cm (W) x 46.5cm. (D). The HR Polyurethane foamshall be moulded with density 45±2kg/m3-and Hardness load 16 ±2 kgf as.per IS:.7888-for 25% compression. The seat cover shall be injection moulded in black co-polymer polypropylene and back cover is vacuum formed from ABS sheets. The one-piece armrests shall be made of black integral skin polyurethane with 50-70 Shore 'A' Hardness and reinforced with M.S. insert. The armrests shall be scratch and weather resistant. The armrests shall be fitted to the seat with seat/armrest connecting strip assembly made of 0.5 ±0.05-cm. thick HR steel.The tubular frame shall be cantilever type & made of 0 2.54±0.03cm x 0.2 ±0.016cm.thk M.S. E.R.W tube and black powder coated (DFT 40-60 microns). Overall Dimensions of Chair shall be Seat Height -45.0cm. Height -81.5cm, Width & Depth of Chair as measured from pedestal - Width-59.0 cm and Depth-63.0 cm. As per Direction of Engineer in Charge

Supply installation & Placement of Table : Materials & dimension (+/- 2mm) code dimension (mm) code dimension (mm) code dimension (mm) a 600 e i b 600 f j c 450 g k d 330 h i table legs meterials & size : oval metal tube thick 1.5 mm color : silver powder coating table top materials & size : (density / type) lxwxt 600 x 600 x 8 mm color : partial black temered glass top full black tempered glass table bottom materials & size : (density / type) lxwxt 500 x 500 x 5 mm color : full black tempered glass. As per Direction of Engineer in Charge

Supply installation & Placement of table Angular 1 Seater corner Table: Top work surface: all tops are made from 25 ± 0.5 mm thick prelamin ate particle board (PLB) as per 15•12823 edge duly sealed with 2mm thick pvc beading. Understructure: Legs: legs are made from 18 ± 0.5 mm thick prelaminate twin board (PLT) as per 15- 12823, having a curved profile with 0.8 mm thick pvc lipping of matching colour. Modesty panel: made from pre laminated twin boards of 18±o.5 mm thick as per is 12853 in two shades. Wire carrier: made from 1.0 ±0.1 mm thick powder coated 50 microns (±10) ms crca sheet, running along the width of desk fitted on the modesty panel from inside. As per Direction of Engineer in Charge

Supply installation & Placement lockable Pedestal: drawer side buttom side & drawer back. Crca (d) grade as per is-513. Drawer front:- metal front straight edge. 18mm thk wooden front post formed. Drawer box- 225mm (w) x 380mm (d) x 98mm (h). File drawer - 225mm (w) x 380mm (d) x 247mm (h). Construction & materials: welded assembled. 0.6 mm thk crca for metal top & drawer front. 0.8 mm thk crca for body shell, side stiffners, & bottom. 1.2 mm thk crca for top & bottom stiffners. 0.5 mm thk crca for drawer side buttom side & drawer back. Crca (d) grade as per is-513. Drawer front:- metal front straight edge. 18mm thk wooden front post formed.18mm thk wooden plb front full straight edge / pvc lipping on all edges. Drawer specifications:- all drawers are double extension precision ball slide. 390 wide pedestal file drawer – suitable for storing fullcase file in depth wise manner . A4 file in width wise manner. 450 wide pedestal file drawer – suitable for storing fullcase file in depth wise manner . A4 file in width wise manner. 2 nos. Of file hanger provided in a file drawer. File drawer provided with fifth roller arrangeme- nts. For drawer pulling sidewise tappered recess is provided in shell behind the drawer front. Locking:- 10 cam lock & cental lock rh locking with actuator & locking chnnel mechanism for box file pedestals. 10 cam lock with indiviual rh locking for (3 big box) pedestal. Top panel:- 8mm thk metal straight edge 18mm thckness wooden top post form/ pvc lipping on 3 edge. Leveler & castor:- swivelingnon lockable castor mounted below the body shell. Portion in drawers:- optional accessory for box drawer. Plastic pencil tray:- optional accessory. Application/ mounting environment: suitable for pushing below wok surface which has got a height of 725mm from below. Finish:- epoxy polyester powder coated to the thickness of 50 microns(+-10 As per Direction of Engineer in Charge

Supply installation & Placement of table : DESK with Pedestal:: DESK with Pedestal: : Table Top Panel: Made of 25mm Thick (±1mm) Particle Board clad with decorative post formed laminate on top side & balancing laminate on bottom side with 30mm MDF pad. Post forming edge on longitudinal side. Leg: Made of 18mm & 25mm Thick (±1mm) MDF Board with 2 side godrej PU painted finish & hardness 2H. 18mm thk wooden front post formed.18mm thk wooden plb front full straight edge / pvc lipping on all edges. Drawer specifications:- all drawers are double extension precision ball slide. 390 wide pedestal file drawer – suitable for storing fullcase file in depth wise manner . A4 file in width wise manner. 450 wide pedestal file drawer – suitable for storing fullcase file in depth wise manner . A4 file in width wise manner. 2 nos. Of file hanger provided in a file drawer. File drawer provided with fifth roller arrangements. For drawer pulling sidewise tappered recess is provided in shell behind the drawer front. Locking:- 10 cam lock & cental lock rh locking with actuator & locking chnnel mechanism for box file pedestals. 10 cam lock with indiviual rh locking for (3 big box) pedestal. Top panel:- 8mm thk metal straight edge 18mm thckness wooden top post form/ pvc lipping on 3 edge. Leveler & castor:- swivelingnon lockable castor mounted below the body shell. Portion in drawers:- Plastic pencil tray accessory. Application/ mounting environment: suitable for pushing below wok surface which has got a height of 725mm from below. Finish:- epoxy polyester powder coated to the thickness of 50 microns(+-10 As per Direction of Engineer in Charge

Godrej and Boyce Mfg. Co. Ltd.

DESIGN-M