Development of jetty at Abdul Kalam Marg

Amount

Appendix A:Pile & Pile Cap

od151152/2021_2022 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-40 of<br>specified diameter and length below pile cap, to carry a safe working load not less than specified,<br>excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and<br>temporary casing of appropriate length for setting out and removal of same and the length of the pile to<br>be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete,<br>including removal of excavated earth with all its lifts and leads (length of pile for payment shall be<br>measured up to bottom of pile cap).<br>Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.<br>700 mm dia piles specification as per 20.2A.2 of DSR

od151159/2021_2022 : Providing Steel Liner 10mm thick for Curbs and 6 mm thick for Steining of Wells including Fabricating and Setting out as per Detailed Drawing.

20.6.2.1 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile above 50 tonne and upto 100 tonne capacityInitial test

20.6.2.2 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile above 50 tonne and upto 100 tonne capacityRoutine test

APPENDIX B:Construction of Beam, Slab, And Deck Slab

od151147/2021_2022 : Providing and laying in position machine batched and machine mixed design mix M-40 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge specification as per 5.33.1 of DSR. Note:- Cement content considered in this item is @ 360 kg/ cum. <br>All work upto plinth level

5.9.21 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick.

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

od151161/2021_2022 : Providing and laying in position cement concrete of specified grade properly mixed and consolidated with hand rammers ,including cost of conveyance of all materials,labour,curing,lead lift etc. complete as directed by Engineer-in-Charge at all levels.For screed concrete 1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per 4.1.3

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Appendix C:JETTY FIXTURES

od151150/2021_2022 : Providing and fixing in position Rubber arch fenders of size: 200x1000mm of "Dipti"(Model- DA200H) make or equivalent as approved ,fixing in position with M24 Anchor Bolts of SS 316 grade of approved quality and as per the drawing/design satisfying the performance requirements as per technical specifications,with all fixtures and accessories,nuts,anchor bolts etc. complete all as per drawing,detailed specifications and direction of Engineer-in-charge.

od151153/2021_2022 : Provide and fixing to lines and levels 30 tonne capacity cast steel bollard single horn (twin lobe) type including supplying and fixing in position with all fixtures:

Pile chipping

2.4.1.C : Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres <br> Prestressed / Reinforced cement concrete grade M-20 & above. - By Manual Means <br>

M J JOY & COMPANY

CUBE INDIA ENGINEERING

Bidder Name

CUBE INDIA ENGINEERING

kabeer m

M J JOY & COMPANY