SPECIAL REPAIRS AND IMPROVEMENT TO GUARD ROOM P-7 AND WATCH TOWER P-31, P-32 AND P-33 AT TS(K) AND SPECIAL REPAIR FOR REPLACEMENT OF CEILING FAN, EXHAUST FAN AND WATER HEATER FOR MARRIED ACCOMODATION AT NAD ALWAYE UNDER GE NS KOCHI

Amount

Demolition of unreinforced cement concrete including roof treatment from roof chajjas and similar suspended work complete all as specified and as directed

Material and Labour for brushing neat cement slurry with 3.00 Kg of cement per Sqm with WPC complete all as specified and as directed. Note : WPC will be measured and paid separately.

Material and Labour for 25 mm thick Cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in floor finished even and fair complete all as specified and as directed.

Material and Labour for Rendering 15mm thick on fair faces of concrete surfaces in CM 1:4 finished even and smooth without using extra cement with using WPC complete all as specified and as directed. Note: WPC will measured and paid separately.

Supply only integral water proofing compound.

Material and Labour for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces complete all as specified and as directed.

Material and Labour for applying APP based Polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick reinforced with Polyster nonware fabric (not less than 150 gms/sqm) laid on primed surface by forced applied complete all as specified and as directed.

Demolition of reinforced cement concrete as in fins, fascia etc complete as directed by Engineer In Charge.

Material and Labour for Reinforced cement concrete 1:2:4 Type B0 using 12.5 mm graded stone aggregate as in fins, fascias, parapets etc with necessary scaffolding complete all as specified and as directed.

Use and Labour for Form work to fascia, fins etc for rough finished surface of concrete complete all as specified and as directed.

Material and Labour for Mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and as directed.

Roughening of surfaces of old concrete floor by picking sweeping clean and washing down with water to remove dust etc complete all as specified and as directed.

Demolition of unreinforced cement concrete in ground floors and paving n.exc. 15cm thickness (below or above ground level) complete all as specified and as directed.

Material and Labour for 75mm thick cement B1 1:2:4 (40mm graded aggregate) finished even and smooth without using extra cement complete all as specified and as directed.

Material and Labour for Screed bed or bedding layers of mortar 20mm thick for laying floor finishes in CM 1:6 complete all as specified and as directed.

Material and Labour for joint less Non Skid ceramic tiles 7 to 8mm thick, light coloured (square/ rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the existing complete all as specified and as directed.

Material and Labour for Rendering 10mm thick on fair faces of brick work or concrete surfaces in Cement Mortar 1:4 on walls complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Material and Labour for joint less Non Skid ceramic tiles 7 to 8mm thick, light coloured (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile complete all as specified and as directed.

Material and Labour for Glazed ceramic tiles in vertical surface 350x250mmx7mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc, including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed

Material and Labour for Rendering 15mm thick on other than fair faces of brick/stone work in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed

Material and Labour for Rendering 10mm thick on fair faces of brick work or concrete surface on ceiling plaster in CM 1:4 finished even and smooth without using extra cement complete all as specified and as directed.

Material and Labour for rendering 15mm thick on stone masonry surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting any gauge or any thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

Material and Labour for 0.50mm thick Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Ditto All as per Serial Item No 26 but for plain steel sheet of 0.50mm thick.

Supply & Fix steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt weld tubes conforming to IS 1166-1979 Gde St-240 complete all as specified and as directed.

Material and Labour for two coat of synthetic enamel paint over a coat of red oxide primer on new steel surfaces not exceeding 10 cm girth including preparation of surfaces complete all as specified and as directed.

Material and Labour for two coat of synthetic enamel painting over a coat of red oxide primer on new steel surface of any description, not otherwise described, over 10cm width or girth including preparation of new surface complete all as specified and as directed.

Material and Labour for preparation of new plastered surfaces of wall and apply of two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

Material and Labour for complete removal of existing treatment and preparation of old surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

Material and Labour for preparation of new plastered surfaces of wall and apply of two coats of antifungal paint over a coat of primer complete all as specified and as directed.

Material and Labour for complete removal of existing treatment and preparation of old surfaces of wall and applying two coat of antifungal paint over a coat of primer complete all as specified and as directed.

Material and Labour for one coat of white wash on ceiling surface including preparation of old ceiling surface complete all as specified and as directed.

Material and Labour for preparation of new surfaces of plastered or unplastered ceiling and applying three coats of white wash complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as directed by EIC.

Demolition of Brick work or stone/boulder masonry, laid built in cement mortar complete all as directed by EIC.

Material and Labour for PCC solid block Masonry made of cement blocks type C1,1:3:6 (20mm graded aggregate) exceeding 10cm in width and setting in cement mortar 1:6 including all scaffolding etc, complete all as specified and as directed.

Taking down chowkat with shutters (without taking off shutters from the frame) not exceeding 1.5 sqm complete all as directed by EIC.

Taking down chowkat with shutters (without taking off shutters from the frame) exceeding 1.5 sqm and not exceeding 4 sqm complete all as directed by EIC.

Material and Labour for second class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed.

Supply& Fix 35mm thick second class Hard Wood framed, paneled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces, the size of rail and style as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

Supply& Fix 35mm thick second class Hard Wood Glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain chamfered or rounded, mitered and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Supply& Fix 25 mm thick flush shutters, solid core construction, with block board core and both face is covered with decorative face veneer with lipping/frame to match as in cupboard shutters complete all as specified and as directed.

Supply& Fix Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

Supply& Fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed.

Supply& Fix Aluminium anodised, barrel tower bolts of extruded section and fixed of size 150mm complete all as specified and as directed.

Supply& Fix Aluminium alloy, anodised, sliding door bolt of size 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Supply& Fix mild steel butt hinges 100mm, medium weight, complete all as specified and as directed.

Supply & Fix Extruded aluminium bow handles of size150mm, fabricated type, anodised complete all as specified and as directed.

Supply & Fix Floor door stopper of aluminium alloy body of size 150mm and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Supply & Fix Mild steel 300mm size ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

Supply & Fix mild steel butt hinges 75mm, medium weight, complete all as specified and as directed.

Supply & Fix 100mm Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

Supply & Fix Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed.

Supply & Fix mild steel work in bands and hold fasts etc and similar small articles conforming to Fe 290 Grade E 165 complete all as specified and as directed.

Material & Labour for providing cement concrete Type B1, 1:2:4 (20mm graded aggregate) as in bed plates of hold fast and similar work including formworks complete all as specified and directed.

Material & Labour for two coat of synthetic enamel painting over a coat of pink primer of wooden surface of any description, not otherwise described, over 10cm width or girth including preparation of new surfaces complete all as specified and as directed.

Supply & Fix Anodised aluminium frame powder coated for doors, windows ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and as directed.

Supply & Fix powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws anodised aluminium fitting such as peg stays 150mm long (1 No) hinge type B21 100mm long (2 Nos) suitable handle (1 No) complete all as specified and as directed.

Supply & Fix 4 mm thick ordinary glass pane glazings with oil putty exceeding 0.5 sqm in each pane complete all as specified and as directed.

Supply & Fix 4 mm thick ordinary glass pane glazing with oil putty not exceeding 0.5 sqm each pane complete all as specified and as directed.

Supply & Fix in repairs Vitreous China Wash basins of size 630x450mm (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but including waste pipe complete all as specified and as directed.

Supply & Fix in repairs, 10 litre capacity PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

Supply & Fix Chromium plated fancy type Bib Tap 15mm with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

Supply & Fix Chromium plated fancy type Angular Stop cock, 15mm with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and as directed.

Supply & Fix Chromium plated fancy type with long shank and cup (Concealed Type) Stop Cock 15mm, screwed both ends for iron pipe for unions and fixed complete all as specified and as directed.

Supply & Fix Flush pipe of size 32 mm dia polyethylene of low or high density or PVC for low level cistern complete all as specified and as directed.

Supply & Fix PVC connection 15mm with PTMT nuts of length 450mm long complete all as specified and as directed.

Supply & Fix 15mm dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

Taking down steel tubing 15mm and connections, including cleaning for re-fixing or removal to store complete all as directed by EIC.

Taking down steel tubing 20mm and connections, including cleaning for re-fixing or removal to store complete all as directed by EIC.

Supplying and laying of CPVC pipes 16mm dia SDR 11 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of CPVC pipes 20mm dia SDR 11 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supply & Fix grating doom 100mm dia of PTMT complete all as specified and as directed.

Supply & Fix brass chromium plated tubular towel rail 20mm dia D type 60 cm long between flanges complete all as specified and as directed.

Material & Labour for 32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed complete all as specified and as directed.

Supply & Fix in repairs Vitreous china squatting pan 'Orissa' pattern of size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe and making good to floor complete all as directed by EIC.

Supply & Fix Brass Chromium plated shower rose with or without swivel joints,15mm bore, fancy type, 125mm size, including fixing to steel pipe or union complete all as specified and as directed.

Dismantling water tanks and removing to store capacity of tank exceeding 250 litre & not exceeding 500 litre capacity complete all as specified and as directed.

Supply & Fix 500 litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Supply & Fix 15mm Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete and making good disturbed surfaces of walls, floors, ceiling etc and applying distemper / emulsion paint to match with existing surface, all as specified and directed.

Material and labour for point wiring with 1.5 sqmm PVC insulated unsheathed single core multistranded copper conductor cable, FRLS, ISI marked drawn through and including PVC conduit of suitable size and all accessories, not less than 2mm thick, fire resistant, ISI marked including 2 mm thick and 4cm depth GI sheet pressed terminal box ( recessed) with 3 mm thick laminated hylem sheet top cover including 1.50 Sqmm PVC insulated unsheathed multistranded single core copper conductor FRLS, ISI marked cable as earth continuity conductor and making good the disturbed surfaces of walls, floors, ceiling etc ,all as specified and directed for One light point controlled by one switch one way

Ditto All as per Sl Item No 86, but for One light point controlled by two 2-way switches, with cables 1.5 sqmm size

Ditto All as per Sl Item No 86, but for One ceiling fan/Exhaust fan point controlled by one switch one way.

Ditto All as per Sl Item No 86, but for One 3 pin 5 Amps socket outlet controlled by one switch on independent board

Ditto All as per item No. 86, but with 2.5 Sq mm cable for wiring and 2.50 Sqmm cable as earth continuity conductor for one 16 Amps switch socket outlet on independent board.

Taking down Ceiling fan, Ceiling cable end, dismantling blades and removing fan and blades Painting of ceiling fans complete, in situ with one coat of synthetic enamel paint by spraying including filling cavities with filler, after cleaning all dust etc, with and including re- hanging Ceiling fan in the same location as directed by Engineer In Charge.

Supply and Fix fan hanging rod of standard size 1.5 meter length all as specified and directed by the Engineer In Charge.

Supply and fixing ceiling fan 1200 mm sweep, 230 volts, BEE 5 star rated (BLDC) ISI Marked with canopy including all accessories such as nuts, bolts, clamps etc complete all as directed by Engineer-in-Charge.

Supply and fix fluorescent LED tube light fitting, 1x20W, 230V, with extruded aluminium housing and high quality PC Diffuser, efficiency of 125 Lumen/watt including LED lamp of 20Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including taking down old one complete all as directed by Engineer-in-Charge.

Supply and fixing new generation energy saving and environmental friendly long life LED Street light 60 watt made up of pressure die cast aluminium housing with high power LED lumen efficiency 110 Lumen/watt lighting source and lens embedded PC cover having Top Opening separate driver compartment with IP66 Protection and impact resistance of IK07 with 10KV Built-in surge protection device complete all as specified and as directed.

Supply and fix rectangular LED Flood light with innovative thermal management and available in multiple optics and equipped with IP 66 protection mounted on stand with a height of 1.30 metre medium grade Galvanised pipe 50 mm grade fixed on a revolving round made with rubber wheel can be transportable type from one point to another point, The LED flood light fitting is fixed or pivoted in the GI pipe in an adjustable pin so that to rotate the light 0 to 360 degree from the pipe, the total height of the light fitting to be 1.3 meter. The system about Rotatable and portable with LED Flood light of cat part No.LFLN-120-CDL/60-M with surge protection 4 KV Drive and external surge protection of 5KV of Model PLUTO of Crompton or equivalent in Philips/Havells making electric connections by insulated unsheathed multistranded single core copper conductors FRLS, ISI marked cable, complete all as specified and directed.

Supply& Fix Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings including taking the old holder complete all as specified and as directed

Supply and fix switch piano, flush type, 6 Amps, SP, one way, complete all as specified and as directed

Supply and fix switch piano, flush type, 6 Amps, SP, two way, complete all as specified and directed.

Supply and fix ceiling rose, surface type bakelite, 65x50mm, 3 terminals, complete all as specified and directed.

Supply and fix switch socket combination, 2/3 pin, 6 Amps, flush type, complete all as specified and directed.

Supply and fix Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed.

Supply and fix switch socket combination 6 pin 6/16Amps, flush type, multipurpose, complete all as specified and directed.

Supply and fix fan regulator, electronic socket type, hume proof, AC, 240 Volts, 5 step, complete all as specified and directed.

Material and labour for sub main wiring with 2 runs of 2.5 Sq mm PVC insulated unsheathed single core multistranded copper conductor cable, FRLS, ISI marked and one run of 2.5 Sq mm multistranded insulated copper conductor cable, FRLS, ISI marked as earth continuity conductor drawn through and including PVC conduit of suitable size and all accessories, not less than 32mm size, fire resistant, ISI marked and making good the disturbed surfaces of walls /floors/ceiling etc with and including removing the existing aluminium sub main wiring cable, complete all as specified and directed.

Supply and fix sheet metal enclosure for MCB DB TPN 4 ways, 415V with 200 Amps bus bar, double door, complete all as specified and directed.

Supply and fix sheet metal enclosure for MCB DB SPN 8 ways, 240V, with 200 Amps bus bar, double door, complete all as specified and directed.

Supply and fix sheet metal enclosure for MCB DB SPN 2 ways, 240V, with 200 Amps bus bar, single door, complete all as specified and directed.

Supply and fix in repairs MCB SP 6 to 32 Amps, complete all as specified and directed.

Supply and fix in repairs Isolator, DP 32 Amps, complete all as specified and directed.

Supply and fix MCB TPN 63 Amps, 415 volts complete all as specified and directed.

Supply and fix RCCB, four pole, 30mA, 63 A, 415V, complete all as specified and directed.

Supply and fix RCCB, double pole, 40 A, 30mA, 415V, complete all as specified and directed.

Material and Labour for Earthing of Poles with GI wire 4mm dia with galvanised MS earth plate of size 600 x 600 x 6 mm buried directly in ground vertically to a depth not less than 2.25 metre below ground level, earth plate shall be packed on all side with charcoal mixed with salt to a thickness of 150mm in layers, connected to GI earth wire 4mm dia (8 SWG) protected by GI pipe 15mm bore (light grade) and watering pipe 20 mm dia (light grade) of suitable length, with necessary earth work including disposal of surplus soil to a distance not less than 50 metre, PCC pit chamber with RCC cover frame, funnel, wire mesh. The GI earth wire 8 SWG under the earth and on the pole up to a height of 1.5 metre shall also be protected by 15mm dia GI pipe (light grade) & GI pipe to be fixed with poles by the means of 2 Nos flat iron clamp 25 x 3 mm size complete with bolts, nuts and washers etc. all as specified and shown in electrical plate No 3 of SSR Part I - 2009 including testing on completion. Note : - Main earthing lead from earth plate to test point & up to 7.5 Metre to be provided . The cost for the same shall be deemed to be included in the above quoted rate.

Supply and fixing ceiling fan 1200 mm sweep, 230 volts, BEE 5 star rated (BLDC) ISI Marked with canopy and hanging rod with all accessories such as nuts, bolts, clamps etc complete including dismantling and depositing old one in MES Store at AGE B/R Alwaye all as per directed by Engineer-in-Charge.

Supply and fixing ceiling fan 1400 mm sweep, 230 volts, ISI Marked with canopy and hanging rod with all accessories such as nuts, bolts, clamps etc complete including dismantling and depositing old one in MES Store at AGE B/R Alwaye all as per directed by Engineer-in-Charge.

Supply& Fix Exhaust fan heavy duty 450 mm sweep 1400 RPM, 220 volts with and including making suitable wiring, necessary holes in the wall and making good with the existing finishing complete all as specified and as directed.

Ditto All as per Sl Item No 117, but for Exhaust fan heavy duty 380 mm sweep 1400 RPM, 220 volts.

Supply& Fix Storage type water heater Geyser of 25 litres capacity BEE 5 Rated connecting inlet/outlet/vent pipes, electric/earth connections, mounting bolts, nuts and carrying out testing for proper functioning of all complete all as specified and directed by Engineer-in-Charge.

Supply& Fix Storage type water heater Geyser of 50 litres capacity BEE 5 Rated connecting inlet/outlet/vent pipes, electric/earth connections, mounting bolts, nuts and carrying out testing for proper functioning of all complete all as specified and directed by Engineer-in-Charge.

Amount of Credit Schedule shall be deducted to arrive the Contract Sum.

KENZ CONSTRUCTIONS