Interior and Fit-out works of Gail (India) Limited, Tower-G, 4th, 5th and 6th Floor, at World Trade Centre, Nauroji Nagar, New Delhi-110029

GENERAL ABSTRACT OF COST

Name of Work : INTERIOR/ FURNISHING WORK OF GAIL INDIA, NEW DELHI.

Sub Head No. Description DSR NDSR/MR Total

CHAPTER-1 CARRIAGE OF MATERIALS 19,764.00 0.00 19,764.00

CHAPTER-8 REPAIRS TO BUILDING 1,00,643.00 0.00 1,00,643.00

CHAPTER-9 METAL WORK 36,700.00 0.00 36,700.00

CHAPTER-10 WATER PROOFING 89,349.00 0.00 89,349.00

CHAPTER-11 FURNITURE WORK 0.00 11,08,64,799.17 11,08,64,799.17

CHAPTER-15 UPS System Work 0.00 92,40,000.00 92,40,000.00

CHAPTER-16 Audio And Vedio System (AV BOQ-1) 0.00 3,37,40,460.00 3,37,40,460.00

CHAPTER-17 USB Based VC (AV BOQ-2) 0.00 1,73,66,100.00 1,73,66,100.00

CHAPTER-18 Data Centre Works 0.00 4,92,72,875.00 4,92,72,875.00

CHAPTER-20 FIRE ALARM SYSTEM 20,86,794.30 10,60,584.00 31,47,378.30

CHAPTER-24 Horticulture 0.00 12,44,300.00 12,44,300.00

Multiplication factor for Modified Analysis of Rates @0.973 on DSR Items 92467834.48 41,74,62,010.59 50,99,29,845.07

Grand Total (DSR+NDSR) 50,99,29,845.07

Grand Total (DSR+NDSR) 50,99,29,845.07

Estimated Cost put in the Tender including GST (1) 50,99,29,845.00

Digitally signed by

PRADYUMNA MUKHERJEE

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF GAIL OFFICE , NEW DELHI

ABSTRACT OF COST

NAME OF WORK -INTERIOR AND FINISHING WORK

I.NO DSR CODE DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

SH 1 CARRIAGE OF MATERIALS

1 1.1.18 Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by cum 40 494.1 19764 0

mechanical transport including loading, transporting, unloading to approved municipal dumping ground for

all lifts, complete as per directions of Engineer-in-charge.

Note - item to be applicable in urban areas having directions for restricted hours for movement/ plying of

load carrying motor vehicle of 3.5 cum or more.

Total Carried Over to Abstract for Sub Head: 1.00 Carriage Of Materials : 19764 0

SH 2 CIVIL WORK

1 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and cum 209.44854 7878.5 1650140

shuttering 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone

aggregate 20 mm nominal size derived from natural sources)

2 5.3 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, cum 1 11505.5 11506

balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level

up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1

cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal

size derived from natural sources). for all rcc work

3 5.9 Centering and shuttering including strutting, propping etc. and removal of form for

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 4.5 736.4 3314

4 5.22.3 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding kg 100 107.85 10785

all complete above plinth level. Thermo-Mechanically Cold twisted bars

5 6.38 Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super cum 30.176 10195.45 307658

structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate

includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

6 6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in Sqm 131.2 1123.8 147443

superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

7 13.4.1 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) Sqm 262.4 357.75 93874

13.4.2 15 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) Sqm 125 343.65 42956

8 MR -1 Providing Pest control and Anti-termite treatment by appointing a specialised agency as per the Sqm 6649.16 225 1496061

specifications mentioned by the Bureau of Indian Standards and Agencies specifications (whichever is

higher), for General Civil, Plumbing,/ Drainage and timber. The termite treatment has to be done in two

stages as pre-renovation and during renovation. Vendor should provide 2 yrs warranty on completion of

9 MR -2 Preparation of complete set of shop drawings including finishing, MEP services, details, design calcualtions LS 1 4607323.12 4607323.12

etc. and any other details as and when desired by Engineer In charge /client. A qualified professsional for the

purpose shall be appointed after due appproval from Engineer In Charge.

Total Carried Over to Abstract for Sub Head: 2.00 Civil Work : 2267676 6103384.12

SH 3 CLADDING WORK

Digitally signed by

PRADYUMNA MUKHERJEE

1 MR -3 Providing and fixing 12 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut Sqm 45.70 5116.46 233801.76

for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved

shade, colour and texture laid over 18 mm thick thick HDMR ply board, joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges

to give high gloss finish etc. complete at all levels.. Granite stone slab including machine polishing to edge

to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work Base rate

2 MR -4 Providing and fixing 12 mm thick , mirror polished, premoulded and prepolished,for kitchen platforms, vanity Sqm 18.99 9715.02 184523.20

counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid

over 18 mm thick thick HDMR ply board, joints treated with white cement, mixed with matching pigment,

epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc.

complete at all levels. Quartaz stone slab Base rate 450 Sqft

3 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., metre 77.42 510.95 39560.00

4 8.4 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width metre 73.58 568.95 41866.00

upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

5 8.5 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity each 52.00 978.70 50892.00

counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc.

including moulding, rubbing and polishing of cut edges etc. complete.

6 8.6 Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish Sqm 76.46 506.70 38744.00

complete.Base rate 300Sqft

7 MR -5 Providing and laying vitrified tile flooring with 3mm Spacers CM 1:4 (1 Part Cement: 4 Part M Sand) of 20mm Sqm 270.00 3378.43 912176.10

average. vitrified tiles of approved shade & laying pattern as per drawing in flooring with 3mm spacer joints,

laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) / Tile adhesive by weber / approved

equivalent make, including grouting the joints with graphite grey epoxy resin based grout PPDG-05 of AGL /

Myk make or equivalent and matching pigments, etc. with water absorption less than 0.08%and conforming

to IS:15622, of approved, make, in all colors and shades cleaned & washed with a suitable effective Cleaning

agent or any suitable means as per instructions of EIC, covering to protect tile with 275 GSM – 2 mm thick

Floor guard make or equivalent, joints to be taped, should remain intact till handing over, removed &

disposed of out of the site after completion, etc., complete. The rates quoted shall include the Rate required

to lay the tiles at the proper level if required, the Rate & cutting of tiles for laying borders/ patterns, etc,

complete in all respects as per details.Base rate 60rs kg

8 MR -6 Providing and laying vitrified tile flooring with 3mm Spacers CM 1:4 (1 Part Cement: 4 Part M Sand) of 20mm Sqm 850.00 2277.89 1936206.50

average. vitrified tiles of approved shade & laying pattern as per drawing in flooring with 3mm spacer joints,

laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) / Tile adhesive by weber / approved

equivalent make, including grouting the joints with graphite grey epoxy resin based grout PPDG-05 of AGL /

Myk make or equivalent and matching pigments, etc. with water absorption less than 0.08%and conforming

to IS:15622, of approved, make, in all colors and shades cleaned & washed with a suitable effective Cleaning

agent or any suitable means as per instructions of EIC, covering to protect tile with 275 GSM – 2 mm thick

Floor guard make or equivalent, joints to be taped, should remain intact till handing over, removed &

disposed of out of the site after completion, etc., complete. The rates quoted shall include the Rate required

to lay the tiles at the proper level if required, the Rate & cutting of tiles for laying borders/ patterns, etc,

complete in all respects as per details.600mm x 1200 mm.Base rate 95Sqft

Digitally signed by

PRADYUMNA MUKHERJEE

9 MR -7 Providing and fixing machine cut, mirrorl polished , ONYX stone work for wall lining (veneer work) including Sqm 80.00 28097.00 2247760.00

dado, skirting, risers of steps etc., in required design and pattern. If required with marble stone slab pieces of

different shapes, shades and texture but of even thickness., on 12 mm (average) thick cement mortar 1:3 (1

cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/ sqm including pointing with

white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all

complete as per Architectural drawings, and as directed by the Engineer-in-Charge. Stone slab of any colour

basic price 1500 rs Sqft

10 MR-8 Providing and fixing machine cut, mirror/ eggshell polished ,Italian Marblestone work for wall lining (veneer Sqm 350.00 10102.49 3535871.50

work) including dado, skirting, risers of steps etc., in required design and pattern. If required with marble

stone slab pieces of different shapes, shades and texture but of even thickness., on 12 mm (average) thick

cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/ sqm

including pointing with white cement slurry admixed with pigment of matching shade, including rubbing,

curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab of any colour basic price 450 rs Sqft

11 MR-9 Providing and fixing Stone art work work for wall lining (veneer work) including dado etc., in required design Sqm 50.00 40334.53 2016726.50

and pattern. If required with marble stone slab pieces of different shapes, shades and texture but of even

thickness., on 40 mm (average) thick pasted on ply wall with required adhesive including pointing with white

cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete

as per Architectural drawings, and as directed by the Engineer-in-Charge. Basic price 2200 Sqft

Total Carried Over to Abstract for Sub Head: 3.00 Cladding Work : 171062.00 11067065.56

SH 4 DOOR & WINDOW WORK

1 9.1.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed cum 6.22 142949.7 889219

and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash

fastener shall be paid for separately). Second class teak wood

2 9.112 Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with metre 638.00 102.15 65172

wooden adhesive of approved quality and screws/nails on the edges of the Pre-laminated particle board as

per direction of Engineer-in-charge.

3 9.20.1 Providing and fixing marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block Sqm 316.80 3473.85 1100516

board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical

grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless

Steel butt hinges with necessary screws

4 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and Sqm 2.40 638.35 1532

manufacturer, including providing and fixing top & bottom pivot & spring type fixing arrangement and

making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-

charge (Door handle, lock and stopper etc.to be paid separately).

5 MR-10 Providing Double cylender Floor Spring Combo set With Lock for Glass door (Combo set including Floor set 1.00 15924.17 15924.17

machine,top patch bottom patch ,pivot,Lock with Closing Force EN 3 with Maximum door weight 100 Kg.

Maximum door width 1050 mm.Closing speed : 130° Final closing speed : 15-0°. Hold Open (standard): 90°

hold open. Weight of floor spring approx : 6kg, 5,00,000 cycles Tested. approved make and model all

complete as per the direction of Engineer-in-charge.

6 MR-11 Providing 32x840 mm 2813 SS 304 H type pull Handle for wooden doors. Material : Stainless Steel. Finish : set 1.00 3281.24 3281.24

Satin Stainless Steel (SSS). of approved make and model all complete as per the direction of Engineer-in-

Digitally signed by

PRADYUMNA MUKHERJEE

7 MR-12 Providing Half moon door stoper floor mounted. Material : SS Finish : AB. of approved make and model all pcs 1.00 754.98 754.98

complete as per the direction of Engineer-in-charge.

8 MR-13 Providing and Fixing 240 mm lock body Antique Brass (8489) for wooden doors of approved make and each 98.00 1917.64 187928.72

model all complete as per the direction of Engineer-in-charge.

9 MR-14 Providing Double cylender Floor Spring D-120 for Wooden door with Closing Force EN 4 with Maximum Set 80.00 12849.67 1027973.60

door weight 120 Kg. Maximum door width 1250 mm.Closing speed : 130° Final closing speed : 15-0°. Hold

Open (standard): 90° hold open. Weight of floor spring approx : 6kg, 5,00,000 cycles Tested. approved make

and model all complete as per the direction of Engineer-in-charge.

10 MR-15 Providing top and Bottom Strap/Door Pivot for wooden doors of approved make and model all complete as set 98.00 705.03 69092.94

per the direction of Engineer-in-charge.

11 MR-16 Providing and Fixing 60 mm Ultero Cylinder 1CK Antique Brass Cylinder One side knob and one side regular each 98.00 1602.87 157081.26

key for wooden doors of approved make and model all complete as per the direction of Engineer-in-charge.

12 MR-17 Providing and Fixing REMO Rose Handle Antique Brass for Store, of approved make and model all complete each 60.00 3949.10 236946.00

as per the direction of Engineer-in-charge.

13 MR-18 Providing and Fixing HDH 01 Rose Handle Antique Brass Exexutive cabin of approved make and model all each 36.00 4878.30 175618.80

complete as per the direction of Engineer-in-charge.

14 MR-19 Providing and Fixing Twist Rose Handle Antique Brass for Director cabin of approved make and model all each 2.00 5342.90 10685.80

complete as per the direction of Engineer-in-charge.

15 MR-20 Providing and Fixing 450x15x15 mm ss 304 Tower bolt -Square Type with screw for Wooden Doors of each 98.00 1986.17 194644.66

approved make and model all complete as per the direction of Engineer-in-charge.

16 MR-21 Providing and Fixing Ecstacy Rose Handle Antique Brass Exexutive cabin of approved make and model all each 6.00 4413.70 26482.20

complete as per the direction of Engineer-in-charge.

17 MR-22 Providing and Fixing 60 mm Ultero Cylinder Keyless Antique Brass Cylinder One side knob and one side coin each 6.00 1486.72 8920.32

release for wooden doors of approved make and model all complete as per the direction of Engineer-in-

18 MR-23 Providing and Fixing 240 mm lock body Antique Brass for wooden doors of approved make and model all each 6.00 1672.56 10035.36

complete as per the direction of Engineer-in-charge.

19 MR-24 Providing and Fixing Concealed Door closer T660 -60 kg (CE certified) for wooden doors of approved make each 6.00 7340.68 44044.08

and model all complete as per the direction of Engineer-in-charge.

20 MR-25 Providing and Fixing SS 304 Hinges Four Ball Bearing 100x75x3 mm (with screws) for wooden doors of each 6.00 487.83 2926.98

approved make and model all complete as per the direction of Engineer-in-charge.

21 MR-26 Providing and Fixing 300x15x15 mm ss 304 Tower bolt -Square Type with screw for Wooden Doors of each 6.00 1765.48 10592.88

approved make and model all complete as per the direction of Engineer-in-charge.

SH 5 FLOORING WORKS

VITRIFIED FLOOR TILES

1 Providing and laying vitrified tile flooring with 3mm Spacers CM 1:4 (1 Part Cement: 4 Part M Sand) of 20mm

average. vitrified tiles of approved shade & laying pattern as per drawing in flooring with 3mm spacer joints,

laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) / Tile adhesive by weber / approved

equivalent make, including grouting the joints with graphite grey epoxy resin based grout PPDG-05 of AGL /

Myk make or equivalent and matching pigments, etc. with water absorption less than 0.08%and conforming

to IS:15622, of approved, make, in all colors and shades cleaned & washed with a suitable effective Cleaning

agent or any suitable means as per instructions of EIC, covering to protect tile with 275 GSM – 2 mm thick

Floor guard make or equivalent, joints to be taped, should remain intact till handing over, removed &

disposed of out of the site after completion, etc., complete. The rates quoted shall include the Rate required

to lay the tiles at the proper level if required, the Rate & cutting of tiles for laying borders/ patterns, etc,

complete in all respects as per details. Double charge vitrified tile polished finish of size

Digitally signed by

PRADYUMNA MUKHERJEE

MR-27 Size of Tile 600 x 600 mm base rate 65 sqm 110.88 1736.58 192551.99

MR-28 Size of ITALIAN MARBLE 600 x 1200mm in CORRIDORS base rate 95 sqm 2400.00 2103.42 5048208.00

MR-29 Glazed Vitrified tiles Matt/Antiskid finish of Size of Tile 600 x 600 mm base rate 70 sqm 600.00 1815.70 1089420.00

2 11.43 Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive sqm 800 633.6 506880

(Water based) conforming to IS: 15477, in average 3mm thickness.

3 11.48.4 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic sqm 3110.88 174.5 542849

coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and

finishing complete as per direction of Engineer-in-charge. Size of Tile 1000x1000 mm

4 MR-30 Providing and laying gang saw cut 18 mm thick granite flooring , mirror polished pre moulded and pre sqm 136.92 3613.79 494800.1268

polished machine cut granite stone of required size and shape of approved shade, colour and texture in

footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4

(1 cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment,

epoxy touch ups etc. complete as per direction of Engineer-in-Charge. basic rate of granite 150 Sqft

5 11.54.2 Providing and fixing removable raised/false access flooring with system and its components of approved sqm 130.00 5977.35 777056

make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load

bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as

per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness

minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x

3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI

fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment

upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be

fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine

screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm

thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws

ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly

shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the

system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical

conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the

Engineer-in-charge.

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high

pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an

enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel

Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and

20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and

cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core

mixed with lightweight foaming compound.

The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology

upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a

Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel

which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum

1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as

per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure

the quality of the product 450 mm Finished Floor Height (FFH).

Digitally signed by

PRADYUMNA MUKHERJEE

6 MR-31 Providing and fixing Engineered wooden flooring 15 mm up to 3 mm top layer, core layer pine wood oak sqm 97.20 5419.64 526789.01

finish or equivalent with necessary T- profile and reducer fixing with underlayer 2 mm thick High Density

polyurethane foam having density of approx. 90 kg/cum and 2 mm thick rubber sheet as per manufacureres

specifications and as directed by engineer in charge. base price 350sqft

7 MR-32 Supplying, installation, testing and commissioning of rubberised flooring, 20mm thick with box preparation, sqm 46.80 1935.59 90585.61

adhesive, installation, suitable for gymnasium flooring complete in all respects base rate 125 sqft

8 MR-33 Providing and laying machine cut, mirror polished Italian marble flooring Marble stone flooring, in required sqm 2000.00 12047.77 2,40,95,540.00

design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of

different colours, shades and finished surface texture etc., in linear portions of the building, all complete as

per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including

pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing,

curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick

Italian Marble basic price650 sqft

9 MR-34 Providing and laying machine cut, mirror polished Italian marble flooring Marble stone flooring, in required sqm 460.00 17842.25 8207435.00

design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of

different colours, shades and finished surface texture etc., in linear portions of the building, all complete as

per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including

pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing,

curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick

Italian Marble basic price 1000 sqft

10 MR-35 Providing and laying of 2mm conductive Vinyl rolls as specified and indicated. The cost to include preparing sqm 172.80 2477.55 428120.64

surface to receive vinyl flooring requirements like the floor to be absolutely leveled, hard, dried, even and

free from dirt, grease, moisture , and fixed using required adhesive ( water based adhesives like Arobond 44

of Colourbond mktg/VC 31 of Pidilite Ind. ) and correct laying technique. The make of vinyl flooring shall be of

Armstrong or equivalent of which the specs / samples have to be submitted for approval. basic price 700 sqft

Flammability : B1 Class

Sound Absorption : 3 dB

Sheet width/length : 180/16-25 cm/m

Tile side length : 60.8/60.8 cm/cm

Total wt : 2.9 kg/m2

Colour fastness : 6 stage

Electrostatic loading limit : <2 Kv

Thermal resistance : 0.010 m2K/W

11 MR-36 Providing and laying Carpet plank/ tiles of Yarn type 100% Nylon; Multi-Level Pattern Loop, manufactured sqm 145.00 4258.29 617452.05

using 100% solution dyeing process, Tiles of size 50cm x 50cm / 25cm x 100cm equivalent as per direction of

EIC and site requirement with SSP® Soil Protection treatment ™ or equivalent containing properties of Stain

Repel, with - pro care backing, pro care self guard, procare fiber with recycled content, made from

thermoplastic with commercial very heavy , Class B1, TVOC Release amoutn A level < 0.500mg/m2h Radiant

Panel class 1rated ( ASTM E648), NBS smoke < 450, Pill test -Passed, Anti Static Property less Than 3.5

kv, Texture Appearance Retention Rating of 3.5 for Severe Use, Anti Microbial Treatment-Passes (AATCC-

174). CRI Green Label Plus is certified for indoor air quality, including fixing/ installation with Low/ Zero VOC

content Adhesive. Impact Sound (ISO 10140-3) 20 dB & Sound absorption (ISO 354) Basic Rate 275 Sqft

Digitally signed by

PRADYUMNA MUKHERJEE

12 MR-37 Providing and laying Carpet tiles of Yarn type Nylon (Nylon 6) only; Multi-Level Pattern Loop, manufactured sqm 575.00 2864.67 1647185.25

using 100% solution dyeing process, Tiles of size 61cms x 61cms equivalent as per direction of EIC and site

requirement with SSP® Soil Protection treatment ™ or equivalent containing properties of Stain Repel, with

Ecoworx® Tile- 100% PVC Free/ 100% Bitumen Free/ 100% Recyclable - backing system with recycled content,

made from thermoplastic polyolefin compound with reinforcing layer high-performance environments

requiring modular flooring, having tufted yarn weight of 542.5 gsm/sqm and average yarn density of

Minimum 6128 oz/cu. yd. or more, Nominal total thickness 5.84 mm minimum, Radiant Panel class 1rated (

ASTM E648), NBS smoke < 450, Pill test -Passed, Anti Static Property less Than 3.5 kv, Texture Appearance

Retention Rating of 3.5 for Severe Use, Anti Microbial Treatment-Passes (AATCC-174). CRI Green Label Plus is

certified for indoor air quality, including fixing/ installation with Low/ Zero VOC content Adhesive. Impact

Sound (ISO 10140-3) 20 dB & Sound absorption (ISO 354) 0.2 Class D or equilent as per direction of EIC and

site requirement Basic Rate 185 Sqft

13 MR-38 Supply of 100 mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thichness Rm 1500.00 1392.47 2088705.00

1.30 to 1.50 mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and

Total Carried Over to Abstract for Sub Head: 5.00 Flooring Works : 1826785 44526792.68

SH 6 CEILING WORKS

PLAIN GYPSUM BOARD CEILING

1 12.45.1 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sqm 3000.00 1355.8 4067400

sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side

inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27

mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x

50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of

required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5

mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm

centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips

made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry

wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel

with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush

finish of tapered and square edges of the board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of

primer suitable for board, all as per manufacturer's specification and also including the cost of making

openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all

complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of

painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS

certification marks)

Digitally signed by

PRADYUMNA MUKHERJEE

2 MR-39 Providing and fixing suspended ceiling in recessed grid system - 600 x 600 x12.5mm with Unity 4mm holes, sqm 1750.00 2095.33 3666827.5

c/c 10 mm with upto 0.8 NRC. Material: Perforated plasterboard ,Board type: Ceiling tileOF SIZE Length x

width x thickness: 600X600X12.5mm ,Edge: E+, recessed grid system ( 8mm recess),Perforation: Unity 4mm

Surface: Water-based acrylic paint,Colour: White NCS 0701 Y24R, RAL 9003; gloss 5, Attachment: 15 or

Silhoutte T-grid system Edge section: 20x24 mm angled profile, 15+15 x 8+25 mm cornice moulding

Suspension: Recessed grid system

• Distance between hangers ≤ 1200mm

• Distance from wall to first hanger in direction of load - bearing section ≤ 400mm

• Distance between load bearing sections ≤ 1200 mm.

• Distance from wall to first load - bearing section ≤ 600 mm

• Sub-division executed with cross - sections length 1200 and 600 mm

• Screw spacing for attachment of edge sections length 1200 and 600 mm

• Light sockets of upto 3.0 kg can be integrated directly into the ceiling tiles. In the case of heavier fittings,

load must be taken up directly by the concrete deck or via the grid systemand extra hangers.

Fire rating: A2-s1,d0k

Digitally signed by

PRADYUMNA MUKHERJEE

3 MR-40 Providing and fixing suspended false ceiling- : Size 1188X1998X12.5mm Globe perforation 6-8/18 with 8.7- sqm 800.00 3856.78 3085424

10.5% perforation with NRC upto 0.7 : Regular round perforation of glass fibre reinforced gypsum material,

which includes providing and fixing GI perimeter channels of size 0.55 mm. Thk. having one flange of 20 mm

and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed to brick wall/

partition with help of nylon sleeves and screws, at 610 mm centers. The suspended GI intermediate channels

of size 45 mm,0.9mm thk with two flanges of 15 mm each from the soffit at 900 mm centers with ceiling

angle of width 25mm x 10mm x 0.55mm thk fixed to soffit with GI cleat and steel expansion fasteners. Ceiling

section of 0.55 mm thk having web of 51.5mm & two flanges of 26mm each with lips of 10.5mm are fixed to

the intermediate channels with help of connecting clips and in direction perpendicular to the intermediate

channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling section with 25 mm dry

wall screws at 300 mm centers to G.I. framing in perfect level. Screw fixing is done mechanically either with

screw driver or drilling machine with suitable attachment. Finally the boards are to be joined and finished so

as to have a flush look with uniflot. Air purification & Air quality.Active reduction of air polluants thanks to

Cleaneo Technology effectively reduces concentrations of VOC’s like alcohol, aldehydes, ketons and esters as

well as unpleasant odours from e.g. food or cigarette smoke Air purification properties tested according to

CEN standards and VDI guidelines by Fraunhof Insistute for Building Physics The false ceiling surfaces shall be

prepared to the satisfaction of the Architect, and shall be applied with two coats of primer to the

satisfaction of Engineering in charge

4 MR-41 Providing and fixing suspended acoustic ceiling in visible, but flush grid system ( with technical panel ) 300 x sqm 850.00 4245.34 3608539

1200 x12.5mm flush grid system with high grade, glass fibre reinforced, acoustic, white painted, gypsum tile

with acoustic perforation as Unity Round 4mm c/c 10mm with NRC upto 0.8 . Material: Perforated

plasterboard Board type: Ceiling tile Length x width x thickness: 300X1200X12.5mm Edge: E, recessed grid

system ( 8mm recess)

Perforation: Unity 4mm round

Perforation percent: 11.0%

Surface: Water-based acrylic paint

Colour: White NCS 0701 Y24R, RAL 9003; gloss 5

Attachment: 15mm T-grid system

Edge section: 20x24 mm angled profile, 15+15 x 8+25 mm cornice moulding

Suspension: Recessed grid system

• Light sockets of upto 1.0 kg per sqmtr can be integrated directly into the ceiling tiles.

Digitally signed by

PRADYUMNA MUKHERJEE

5 MR-42 Providing of suspended false ceiling Size 1200x600x12.5mm micro perforation 3.5mmx3.5mm with 15.90 - sqm 130.00 4072.65 529445

17.20 % perforation and upt0 0.9 NRC - Regular Square Perforation of glass fibre reinforced gypsum material,

which includes providing and fixing GI perimeter channels. The furring should be minimum 60mm wide at the

short end joints ( if wood is used, the steel furring can be min. 45mm). The remaining furring can be 45mm

wide of size 0.55mm. thk having one flange of 20mm and another flange of 30mm and web of 27mm along

the perimeter of the ceiling, screw fixed to brick wall/ partition with help of nylon sleeves and screws, at

610mmcenters. The suspended GI intermediate channels of size 45mm, 0.9mm thk with two flange of 15mm

each from the soffit at 900mm centers with ceiling angle of width 25mmx10mmx0.55mm thk fixed to soffit

with GI cleat and steel expansion fasteners. ceiling section of 0.55mm thk having web of 51.5mm thk and two

flanges of 26mm each with lips of 10.5mm are fixed to the intermediate channels with help of connecting

clips and in direction perpendicular to the intermediate channels with center of 333mm perforated

gypboard is then screw fixed to ceiling section with 25mm dry wall screws at 300mm centers to GI framing in

perfect level. Screw fixing is done mechanically either with screw driver or drilling machine with suitable

attachment. Finally the boards are to be joined and finished so as to have a flush look with jointing

compound. Cleaneo Technology - Air purification and air quality active reduction of air pollution thanks to

cleano technology effectively reduces concentrations of VOC's like alcohol, aldehydes, ketons, and esters as

well as unpleasant odours from e.g. food or cigarette smoke. Air purification properties tested according to

CEN standards and VDI guidelines by Fraunhof Institute for building physics.

6 MR- 43 Providing and fixing of Geo 100mm open cell ceiling with cell size of 100x100mm made out Aluminium . The sqm 257.13 2400.13 617133

assembled cell ceiling panels shall be in size of 600x1200 made out of blades in 9mm (W) x 40mm (H). The

assembled cell ceiling panels are then clipped into U-94 carriers in Aluminium, pre-coated in black enamelled

finished at 1200mm c.c. Wire clips shall hold the cell ceiling panels into the U-94 carriers. Once the U-94

carriers are installed then primary angles made out of GMS, type U1040 are cross connected to the U-94

carriers at 1200mm c.c. for lateral bracing The whole ceiling shall be suspended by M6 threaded rods

installed 1200mm c.c.All panel modules must be hingeable through wire clips.

7 MR_ 44 Providing and fixing ceiling system formed as an open metal ceiling with an open area of more than 50%. The sqm 46.31 5342.22 247388

multidirectional ceiling composed of equilateral triangles 600mm modules with perfectly homogeneous

aspect and the im-pression of a uniform assembly. The main blades comprising 100mm height & 25 mm

width interlocked polylams in Extruded aluminium 1.50mm thickness compensating tolerances in x and y

direction. The substructure consists of a form punched perforated profile [U1040] as a lateral grid which is

suspended from the ceil-ing with nonius adjustable upper and lower parts or with threaded rods using official

approved dowel plugs. The grid profiles are to be connected together at the ends by means of longitudinal

connect-ors [U 1041] [screw fasteners]. The spacing of the grid profile is according to the requirements of DIN

EN 13964. On profiles angles, C-band raster as secondary profiles are bolted on by means of C channel

hanger bracket with M6 bolts. Only construction parts ap-proved by the manufacturer may be used. Provide

necessary supports, provisions as per the architects / PM’s Instructions. Toler-ances according to TAIM, DIN

EN 13964 and quality controlled to ISO 9001:2008 approved by TUV. Finish of ceiling is in wood Finish

powder coated with mini-mum 60 microns paint thickness.

Digitally signed by

PRADYUMNA MUKHERJEE

8 MR- 45 Providing And Fixing Modular Baffle Ceiling system: is vertical & horizontal baffle system, exhibiting space- sqm 304.03 9213.40 2801141

delineating characteristics. The system comprises baffles 40mm wide & 150 Deep thickness of minimum

0.5mm GMS, installed at 150mm C/C . Baffle to be perforated having acoustic fleece pasted from inside. The

C shaped shaped carrier rails run perpendicular to the main baffles profiles. Individual baffle lengths between

300 and 2400 mm can be selected. Baffle are supplied with the end cap matching the similar finish of baffle.

Tolerances according to TAIM, DIN EN 13964 and quality controlled to ISO 9001:2015 approved by SIS.

Substructure for Vertical baffle system consisting of C shape carrier of minimum 1.2mm thick installed

perpendicularly to baffles, same was hanged to wall with the help of wall anchor fasteners. Baffles to be

connected perpendicular to C shaped carriers with the help of baffle hanger brackets. The primary profiles

must be connected to one another with longitudinal splice connectors. C shaped baffle carriers to be

installed at maximum distance of 1200mm. in a length of 2400 mm baffles. Baffle width: 40mm Baffle height:

150 mm Individual baffle lengths: Min.300/Max.2400mm Material: Minimum 0.5 mm GMS.

Surface: Selected Digitally printed Woodgrain finish having minimum 80 micron paint thickness.

Manufacturer shall have the fully automatic powder coating system with power and free conveyorize

3mtr/minute capacity. Powder coating plant shall be equipped with latest modern technology with fully

automatic inline Pre-treatment using nano technology, Inline automatic water Drying system after pre-

treatment. Mode of Measurements: Measurements shall be wall to wall without any deductions for lights,

diffuses, columns etc

Digitally signed by

PRADYUMNA MUKHERJEE

9 MR-46 Providing and fixing Veneer finished ceiling feature made of 19mm commercial board and all exposed sqm 380.31 5806.76 2208392

surfaces finished in 4mm thick veneer of approved shade including framing, all fixing hardware, accessories,

making cove, cutout for light fixtures and any other incidentals which may require to secure to false ceiling

and to accomplish the work in all respect as per detail drawings and as directed & approved by architect.

Rate quoted to include vertical drops, making cove and all cut-outs required for light fixtures and other

services cut-outs and necessary supports with hitech rods from the true ceiling complete as directed by

Architect. BR of Veneer 180/-

10 MR-47 Providing and Fixing Custom made Stretch false ceiling to fit exact dimensions with aluminium supports. The sqm 250.00 23227.05 5806763

PVCc ceiling must be stretched and hooked into aluminium rails. Stretch aluminum rails ensuring good

rigidity, to be fixed to the walls or other supports at the specified level. A properitory semi rigid PVC Anchor (

for Tension mounting ) is welded on the outer periphery of the PVC ceiling.

Following are the Technical Specification :

Ceiling Material : Stretchableceiling with PVC Harpoon welded

Thickness : 0.17mm +- 10%

Dimensional Stability : -5 deg to +45 deg C ( No visisble deformation)

Weight : (200 +_ 15 ) g / sqm

Water Vapor permeability :

For Hydrometric degree > 65% RH = 0.0045 g / hr sqm mm Hg

Very effective impermeable barrier to water

Water proof / Dust Proof / Airtight

Resistant to water , dampness, sea water, copper salt solutions and x-rays

Thermal Cofficient : 0.16 kcal/m H C

Fire Classification : B-s2-d0 acc. With DIN EN 14716

Low Emission : CLASS A+ Certified

Total Carried Over to Abstract for Sub Head: 6.00 Ceiling Works : 4067400 22571052.5

SH 7 WALL FINSHES WORK

1 9.105.2 Poviding and fixing partition upto ceiling height consisting of G.I. frame and required board, including Sqm 502.20 1818.15 913074.93

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc

coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal

flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre

with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with

nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm

thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to

centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall

with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling

channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of

9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal

flat head screws, including jointing and finishing to a flush finish with recommended jointing compound,

jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer

suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75mm

overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board

conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks)

Digitally signed by

PRADYUMNA MUKHERJEE

2 MR -48 Poviding and fixing partition upto ceiling height consisting of G.I. frame and required board, including Sqm 3300.00 1283.33 4234989.00

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc

coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal

flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre

with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with

nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm

thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to

centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall

with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling

channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of

9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal

flat head screws,

3 9.140.1 Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved Sqm 6277.14 1224.65 7687303.80

primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in charge

(Frame work shall be paid for separately). 12 mm thick commercial ply conforming to IS : 1328 BWR type

4 MR - 49 Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved Sqm 1200.00 1080.61 1296732.00

primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in charge

(Frame work shall be paid for separately). 8mm thick commercial ply conforming to IS : 1328 BWR type

5 MR - 50 Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved Sqm 941.57 1021.74 962041.29

primer on one face, and fixed on wooden/ steel frame work, complete as per direction of Engineer-in-Charge

6 mm thick commercial ply conforming to IS : 1328 BWR type

6 MR - 51 Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved Sqm TRUE 962.87 962.87

primer on one face, and fixed on wooden/ steel frame work, complete as per direction of Engineer-in-Charge

7 MR - 52 Providing & Fixing of Sleek Partition System SG 75 ie. Single glazed modular system consist of Aluminium sqm 950.00 5806.76 5516422.00

section of 20*75*2 mm thick. All sections duly anodised up to 15-20 microns with 6003 grade and required

accessories ie glass to glass aluminium I sections, T section & 90 degree sections & Glass packing to adjust the

floor level. Ceiling profile & Floor profile and wall profile are 20 mm visible face and 75 mm wide. Profiles will

come in three sides alongwith ( Top, Bottom and Verticle on Wall side) Forth Verticle will come where No

adjusant door comes. Partition will have 10mm toughen glass & insertion of silicon/Thermoplastic gasket to

adhere the glass firm & airtight.

8 MR - 53 Providing & Fixing of Partition Glass Door having SG75 Door Frame with 6003 grade duly Anodized nos 19.00 60442.14 1148400.66

Aluminium Sections having sizes of 75x35x2mm thick, Glass door with 10 mm Toughened Glass including

Hafele/Dorma XLC Door Closure, Hinges, SS Handle (H Type 300mm), SS Bottom Lock, Silicone/Thermoplastic

Gaskets & Screw Caps

9 MR - 54 Providing and fixing flutted glass in partitions etc. with EPDM rubber / neoprene gasket etc. complete as per sqm 237.50 5419.64 1287164.50

the architectural drawings and the directions of engineer-in-charge . Toughened glass 10 mm thickness

8 8.28.1 Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for Sqm 3550.00 1946.25 6909188.00

plain lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative

veneer facings of approved manufacture

9 9.127.2 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede Sqm 1048.10 897.30 940462.00

finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS

: 2046 Type S, including cost of adhesive of approved quality.

Digitally signed by

PRADYUMNA MUKHERJEE

10 MR - 55 providing and installation of ACOUSTIC WALL PANELS. The MDF wall panels shall be composed of Medium Sqm 480.00 6044.21 2901221.00

Density Fiber board (MDF) with a minimum density exceeding 710 kgs/m³, and they shall be covered with PP

foil of Renolit, Germany brand/make with a thickness of 120 microns. The adhesive used for affixing the

panels must be PUR (polyurethane) hotmelt glue, and the design of the panels will be as per the

specifications provided by the architect. The dimensions of the panels are 17-18mm in thickness, 130.5mm in

width, and 2745mm in length.The scope of work includes providing and fixing these MDF wall panels onto a

framework constructed either from MDF or plywood. The framework should have a thickness of 50 mm and a

width ranging from 8mm to 12mm. The installation of the panels can be executed through either the nail-

down method or the pasting method, with the use of a high bonding adhesive suitable for MDF and plywood,

NRC 0.65 upto 1 NRC . The finishing of the MDF wall panels should adhere to the approved architectural

drawings and the directions provided by the Engineer-in-Charge (EIC).

11 MR -56 Providing & Fixing PVC wall covering 1 to 2mm thick as per design and finish having fiber backing for sound Sqm 950.00 2787.25 2647888.00

insulation. Covering to be pasted on Mdf base with adhesive as approved by manufacture. Material should

be fire resistance as per ISO 105-B02 > grade 8 All complete as per engineer in charge

12 MR - 57 Providing & fixing 6 mm thick GRIHA rated lacquered glass with flat polished edge fixed to 5.5 mm thick Sqm 450.00 4335.72 1951074.00

plain MDF board backing with neutral silicone and/or double-sided adhesive pads etc. ,including

polishing/MTG all complete as per the drawing & directions of engineer-in-charge. 6.0 mm thick

13 MR - 57 Providing & fixing 6 mm thick mirror with flat polished edge fixed to 5.5 mm thick plain MDF board backing Sqm 30.00 4335.72 130071.60

with neutral silicone and/or double-sided adhesive pads etc. ,including polishing/MTG all complete as per the

drawing & directions of engineer-in-charge. 6.0 mm thick

13 MR - 58 Providing & fixing commercial grade wall paper of approved shade to MDF/Gypsum board/POP Punning base sqm 800.00 1858.16 1486528.00

backing which have 100% washable, scratch resistance, peel proof, and fire retardant properties, including

preparation on the punned surface for receiving the wall paper, adhesive as per the manufacturer

specification, all complete as per the drawing & directions of engineer-in-charge( Base backing to be paid

14 MR - 59 Providing and fixing electroplating SS PROFILE of colour and design as per engineer in charge Metre 1850.00 708.04 1309874.00

15 9.40.1.2 Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and Metre 1552.74 271.75 421958.00

priming coat on unexposed surface etc. complete : 2nd class teak wood:50 x 20 mm

16 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface sqm 5069.39 262.70 1331728.00

even and smooth complete.

17 MR Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers sqm 4700.00 484.20 2275740.00

specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special

primer applied @ 0.75 ltr /10 sqm

18 MR Providing and applying two or more coats of Textured Paint/ Surface Coating of approved make and shade sqm 940.00 807.00 758580.00

over walls etc. after preparing the surface with a coat of primer and 6 mm thick plaster of paris punning to

give a smooth and even surface etc. complete. base price 85 per sqft

19 13.116 Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade sqm 3000.00 3049.00 9147000.00

texture with following process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is

allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess

sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special

grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6

hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.

Digitally signed by

PRADYUMNA MUKHERJEE

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine

thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet

rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with

compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required

proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without

20 MR -60 Providing and fixing Roller Blind system consisting of a coated aluminium tube of 38 mm diameter of sqm 600.00 2787.25 1672350.00

approved colour with provision of fabric clamping. The Fabric is rolled up and down through a chain drive

system with built in drive gear and an over run brake system. The side brackets are universal type suitable

both for wall and ceiling mounting. The bottom end of the fabric is rolled over an oval shape aluminium tube

with provision to lock the fabric.The rate shall be inclusive of all the necessary material,required hardware,

labour, transportation, necessary for the complete execution of the item . basic price 180 Sqft

21 MR -61 Providing and fixing motorized Roller Blind system with remote consisting of a coated aluminium tube of 38 sqm 280.00 5030.53 1408548.40

mm diameter of approved colour with provision of fabric clamping. The Fabric is rolled up and down through

a chain drive system with built in drive gear and an over run brake system. The side brackets are universal

type suitable both for wall and ceiling mounting. The bottom end of the fabric is rolled over an oval shape

aluminium tube with provision to lock the fabric.The rate shall be inclusive of all the necessary

material,required hardware, labour, transportation, necessary for the complete execution of the item .

22 MR -62 Providing & Fixing 3M & equivalent Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect Sqm 730.00 1316.20 960826.00

film to reproduce Sand-blasting effect on glass with customized designs, thickness of 2 mil (0.05mm) without

adhesive & 3M & equivalentil (0.8)with adhesive having minimum tensile strength of 3.5 pound/inch at 73

F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic,

Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) must be endorsed

by Electronically/computer plotter cut. Applied on glass and other rigid, clear substrates. (partitions, doors,

windows etc.) Available in 5 colours

Total Carried Over to Abstract for Sub Head: 7.00 Wall Finshes Work : 30385034.73 28915093.32

SH 8 REPAIRS TO BUILDING

1 14.75 Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the Sqm 150 670.95 100643

patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based

polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of

Engineer-In-Charge.

Total Carried Over to Abstract for Sub Head: 8.00 Repairs To Building : 100643

SH 9 METAL WORK

1 10.25.2 Steel work welded in built up sections/ framed work, including cutting,vhoisting, fixing in position and Kg 100 172.6 17260

applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames,

guard bar, ladder, railings, brackets, gates and similar works

2 10.16.3 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, Kg 100 194.4 19440

hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted

with special shaped washers etc. complete. Electric resistance or induction butt welded tubes

Total Carried Over to Abstract for Sub Head: 9.00 Metal Work : 36700 0

SH 10 WATER PROOFING

INTEGRAL CEMENT BASED TREATMENT

Digitally signed by

PRADYUMNA MUKHERJEE

1 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement

slurry mixed with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/

sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126

kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

22.5 The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and sqm 144.8 617.05 89349

masonry with polymer mixed slurry.

Total Carried Over B215:B216to Abstract for Sub Head: 10.00 Water Proofing : 89349 0

Digitally signed by

PRADYUMNA MUKHERJEE

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF GAIL OFFICE , NEW DELHI

ABSTRACT OF COST

SI.No. DSR-2021/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

A) SANITARY INSTALLATION

1.0 MR -1 Providing and fixing white vitreous china extended wall mounting Each 2 125619.78 251239.56

water closet Wall hung toilet with electronic cleansing in Seat White

of approved shape including providing & fixing Pneumaticcisten tank

3/6L with full frame with dual flush fitting, ,including seat cover, and

cistern fittings, flush plate with brush gold finish , hand faucet, nuts,

bolts and gasket etc complete. all fitting in brush gold finish

2.0 MR -2 Providing and fixing white vitreous china extended wall mounting Each 1 54171.47 54171.47

water closet Wall hung toilet with electronic cleansing in Seat White

of approved shape including providing & fixing Pneumaticcisten tank

3/6L with full frame with dual flush fitting, ,including seat cover, and

cistern fittings, flush plate with brush gold finish , hand faucet, nuts,

bolts and gasket etc complete. all fitting in crome finish

3.0 MR -3 Providing and fixing white vitreous china extended wall mounting Each 45 28950.00 1302750.00

water closet Wall hung toilet with electronic cleansing in Seat White

of approved shape including providing & fixing Pneumaticcisten tank

3/6L with full frame with dual flush fitting, ,including seat cover, and

cistern fittings, flush plate with brush gold finish , hand faucet, nuts,

bolts and gasket etc complete. all fitting in crome finish

4.0 MR-4 Providing and fixing Toilet paper holder POLISHED CROME : C.P. Each 51 6800.00 346800.00

5.0 MR-5 Providing and fixing under counter wash basin including painting of Each 2 9949.80 19899.60

fittings and brackets, cutting and making good the walls wherever

required. White Vitreous China Wash basin size approx 550x400 mm

including , nuts, bolts and gasket and bottle trap etc complete. Alll

Fitting in brush gold finish

Digitally signed by

PRADYUMNA MUKHERJEE

ABSTRACT OF COST

SI.No. DSR-2021/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

6.0 MR-6 Providing and fixing under counter wash basin including painting of Each 48 8132.11 390341.28

fittings and brackets, cutting and making good the walls wherever

required. White Vitreous China Wash basin size approx 550x400 mm

including , nuts, bolts and gasket and bottle trap etc complete. All

Fitting in crome finish

7.0 MR-7 Providing and fixing inset lighting mirror of superior glass (of Each 2 33995.15 67990.30

approved quality) complete with ground fixed to wooden cleats with

C.P. brass screws and washers complete.

8.0 MR-8 Providing and fixing inset lighting mirror of superior glass (of Each 3 20728.75 62186.25

approved quality) complete with ground fixed to wooden cleats with

C.P. brass screws and washers complete.

9.0 MR-9 Providing and fixing mirror of superior glass (of approved quality) Each 45 4500.00 202500.00

complete with ground fixed to wooden cleats with C.P. brass screws

and washers complete. Size 600 x 900

9.0 MR-10 Providing and fixing wall mounted basin mixture including inner Each 2 10778.95 21557.90

fitting and all fitting as required All Fitting in brush gold finish

10.0 MR-11 Providing and fixing wall mounted basin mixture including inner Each 48 8132.11 390341.28

fitting and all fitting as required Alll Fitting in CROME finish

11.0 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser Each 100 574.30 57430.00

points of approved quality conforming to IS:8931 15mm nominal

12.0 18.21.2.1 Providing and fixing uplasticised PVC connection pipe with brass Each 14 97.75 1368.50

unions : 45 cm length , 15 mm nominal bore

13.0 MR-10 Providing and fixing Liquid soap Dispensor in polished crome in brass Each 2 6491.06 12982.12

, lead free refillable ALL fitting in brush gold finish

Digitally signed by

PRADYUMNA MUKHERJEE

ABSTRACT OF COST

SI.No. DSR-2021/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

14.0 MR-11 Providing and fixing Liquid soap Dispensor in polished crome in brass Each 52 4464.53 232155.48

, lead free refillable ALL fitting in chrome finish

15.0 MR-12 Providing and fixing towel ring round shape crome finished Each 5 2594.06 12970.28

16.0 MR-13 Providing and fixing wall mounted diverter with inner and upper part Each 2 11998.99 23997.97

in brass, in premium finish including all requird accessories to

complete installation

17.0 MR-14 Providing and fixing wall mounted diverter with inner and upper part Each 2 8945.32 17890.64

in brass, finshed in crome polish including all requird accessories to

complete installation

18.0 MR-15 Providing and fixing ceiling mound suare shower head size 305 mm Each 2 53323.41 106646.81

Square in brass with premium finish with dual flow including shower

arm and all accessories as required to complete installation

19.0 MR-16 Providing and fixing ceiling mound shower head in brass with crome Each 2 27506.28 55012.56

finish with single flow including shower arm and all accessories as

required to complete installation

20.0 MR-17 Providing and fixing C.P. brass Spout of approved quality conforming Each 3 34809.00 104427.00

21.0 MR-18 Providing and fixing floor drain of size 600 x 80 mm in SS grade 304 Each 2 6671.10 13342.20

with provision of fixing 12 mm thick tile matching the floor tile in

shower area . Cost including all Accessories as required including

trap, gasket , grouting etc as per engineerg in charge

22.0 MR-19 Providing and fixing floor drain of size 100 x100 mm in SS grade 304 Each 47 2369.00 111343.00

with provision of fixing 12 mm thick tile matching the floor tile in

shower area . Cost including all Accessories as required including

trap, gasket , grouting etc as per engineerg in charge

23.0 MR-20 Providing and fixing Coat Hook. Each 56 1374.02 76945.12

Digitally signed by

PRADYUMNA MUKHERJEE

ABSTRACT OF COST

SI.No. DSR-2021/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

24.0 MR-21 Providing & Fixing of Grab bar 600 mm of non slipping grip as per Each 5 4104.29 20521.45

standard specification of use in disabled toilet complete with

brackets suitable for wall installation as per approved sample

complete in all respect.

25.0 MR-22 Supply,Installation, testing and commissioning of Water Heater Each 5 13384.00 66920.00

complete with heavy gauge hot and cold water flexible pipe

connections, Nano polymer coated tank, 8 bar pressure ,of approved

make complete with all necessary material as directed by Engineer -

in - Charge. 25-Litre Storage capacity

26.0 MR-23 Providing and fixing under counter sink in SS 304 grade double bowl Each 2 4505.00 9010.00

including painting of fittings and brackets, cutting and making good

the walls wherever required. including , nuts, bolts and gasket and

bottle trap etc complete.

27.0 MR-24 Providing and fixing counter top mounted Sink mixture mixture Each 2 9476.00 18952.00

including inner fitting and all fitting as required

28.0 17.28.2.2 Providing and fixing P.V.C. waste pipe for sink or wash basin including Each 2 119.55 239.10

P.V.C. waste fittings complete. Flexible pipe 40 mm dia

29.0 MR-25 Supply installation, testing and commissioning of water cooler with Each 2 89607.43 179214.86

Inbuilt RO purification .Cooling capacity shall be 60 liter & 80 liter

shall be storage capacity.Its should have 7 stages purification

process,fully automatic,rectangular tank with Forced fin and tube

condenser,Non-corrosive SS-304 outer body,Food-grade SS-304

stainless steel inner tank (18/8 or 18/10),PUF

insulation,Reciprocating compressor with R22 Refrigerant.Water

outlet temp is aprrox 17 deg c ,Operating power supply 230 + 10% V

AC,50 Hz,1 PH,No of Cold water Faucet-2.

Digitally signed by

PRADYUMNA MUKHERJEE

ABSTRACT OF COST

SI.No. DSR-2021/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

30.0 Providing & fixinge Restroom Cubicle (of following standard

dimension which includes 600mm door size width) self-supporting

12mm thick compact laminates made out of, urea free,

thermosetting phenolic resins treated Kraft papers as core material

and Amino plastic resin treated decor papers on the finish surface,

conforming to latest and applicable IS: 2046-1995, EN 438:2016 and

NEMA LD3-2005 quality standards with Antivirus, Antibacterial and

Antifungal properties (conforming to ISO 21702:2019, JIS Z2801:2010

and ASTM G21-2015 standards respectively) tofulfil the applicable

requirements of indoor air quality certifications for Greenguard-Gold

standards. This also includes providing and fixing in position

necessary hardware made out of Nylon Polyamide grade 6 &

Aluminium alloy grade 6063-T6 powder coated finish in black and

other available color hardwares as per manufacturer’s specifications

& Architects instructions like (1) Self closing hinges in Nylon

Polyamide grade 6 in gloss finish in available colors (2) Soft closing

thumb turn lock made in nylon polyamide grade 6 in gloss finish in

available colors (3) Single Coat hook in nylon polyamide grade 6 in

gloss finish,available in similar available colors (4) U & F- profiles in

Aluminium alloy grade 6063-T6 with powder coating in available

colors (5) Nylon polyamide grade 6 Adjustable Leg (6) Top rail along

with Nylon Polyamide grade 6 with end cap is a Round D shaped

extrusion made of Aluminium alloy grade 6063-T6 with Powder

Coating in available colors, (7) Rubber, (8) Screws & wall Plugs ( SS-

316 ). The top fitting should consist of Matt finish aluminium alloy

grade 6063-T6 in avilable colors , which will get fixed on pilasters

with SS Screws, All screws will of 316 Grade in stainless steel . All

pilasters are supported

Toilet Cubicle by grade-

with standard 6 Nylon

dimension of Polyamide Thermoplastic

Width x 1500mm Depth, which includes 600mm door size width).

Toilet Cubicle I-Shape (Front Partition) with standard dimension of nos 16 22500.00 360000.00

1995mm Height x 1000mm Width which includes 600mm door size

Digitally signed by

PRADYUMNA MUKHERJEE

ABSTRACT OF COST

SI.No. DSR-2021/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

31.0 MR -63 Providing and fixing ABS Auto aerosol Dispenser, fixed to wooden

cleats with C.P brass screws, complete including cutting and making

good the walls wherever required.

UTEC : UT-630 / Euronics Nos 6 2212.10 13272.59988

32.0 MR -63 Providing and fixing ABS Auto aerosol Dispenser, fixed to wooden

cleats with C.P brass screws, complete including cutting and making

good the walls wherever required.

UTEC : UT-630 / Euronics Nos 6 2212.10 13272.59988

TOTAL FOR SANITARY INSTALLATION

Digitally signed by

PRADYUMNA MUKHERJEE

ABSTRACT OF COST

SI.No. DSR-2021/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

B) WATER SUPPLY AND INTERNAL DRAINAGE SYSTEM

1 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps

at 1.00 m spacing. This includes jointing of pipes & fittings with one

step CPVC solvent cement and the cost of cutting chases and making

good the same including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good the

a) 18.8.1 15 mm nominal dia Pipes Mtr. 250 497.80 124450.00

b) 18.8.2 20 mm nominal dia Pipes Mtr. 150 537.60 80640.00

c) 18.8.3 25 mm nominal dia Pipes Mtr. 100 627.25 62725.00

d) 18.8.4 32 mm nominal dia Pipes Mtr. 18 739.30 13307.40

2 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and testing of joints complete as

per direction of Engineer in Charge.

Internal work - Exposed on wall

a) 18.7.1 15 mm nominal dia Pipes Mtr. 2 286.80 573.60

b) 18.7.2 20 mm nominal dia Pipes Mtr. 10 335.00 3350.00

c) 18.7.3 25 mm nominal dia Pipes Mtr. 10 401.55 4015.50

d) 18.7.4 32 mm nominal dia Pipes Mtr. 5 518.75 2593.75

e) 18.7.5 40 mm nominal dia Pipes Mtr. 15 702.95 10544.25

e) 18.7.6 50 mm nominal dia Pipes Mtr. 30 934.15 28024.50

Digitally signed by

PRADYUMNA MUKHERJEE

ABSTRACT OF COST

SI.No. DSR-2021/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

3.00 MR Providing and fixing low noise insulated Polyproplene piping system

as per DIN EN 12056 and DIN1986-100 with 3 layer pipe made of

External layer -PP, middle layer-Mineral reinforced PP, Internal layer-

PP. push-fit type, food safe, having high impact and stiffness, offering

sound levels of not more than 10 dBA as per DIN 4109 at a flow rate

of 2 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and

tightness as per EN 1277/B and C and DIN 19560, density of pipe =

1.9 g/cm3, elongation break 50% and tensile strength 20

N/mm2,Coefficient of linear expansion 0.09 mm/mK with all

necessary fittings fitted with factory fitted lip ring including cutting

and making good the walls, floors, R.C.C. work etc or also incluiding

painting with ordinary cement based paint for external installation.

(including MS structural support & U clamps as required)

b) 75 OD mm dia Pipes Metre 124 1166.00 0.00 144584.00

4.00 MR Providing and fixing PP white Trap with minimum 50mm water seal

with rubber seal on inlet to push fit hopper for indirect waste

a) 110 mm inlet & 110 mm outlet Long ht Each 3 1505.00 0.00 4515.00

5.00 MR Providing and fixing floor drain (FD) with 50mm outlet and 100 mm

inlet having 19mm seal for indirect floor drain (FD).

6.00 MR Providing and fixing Multi Trap (MT) with 50mm outlet and 100 mm

inlet having 19mm seal for indirect Multi Trap (MT).

Digitally signed by

PRADYUMNA MUKHERJEE

ABSTRACT OF COST

SI.No. DSR-2021/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

7.00 MR Providing, fixing, testing and commissioning of pipe inlet fittings by Each 3 827.00 0.00 2481.00

fixing Tee 110 x50/110 x75 mm (as required) fixed on 'P' traps for

connecting fixture drains/ extension pices in PP including fixing and

sealing inlet joint with drip seal / Pipe seal joint as required

Digitally signed by

PRADYUMNA MUKHERJEE

ABSTRACT OF COST

SI.No. DSR-2021/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

8.00 MR Providing and fixing 1 mm thick stainless steel grating with frame for

floor traps or drains of required pattern including cutting and making

good the floors complete.

9.00 MR Providing and fixing clean out pipe (door piece) for cleaning as

required complete complete with all fitting, clamps, accessories and

10.00 17.77 Providing and fixing M.S. holder bat clamp of approved design to

sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets

made of 50x5 mm flat of specified shape, projecting 75 mm outside

the wall surface and fixed on wall with 4nos, 6mm dia expansion hold

fasteners, including drilling necessary holes in brick wall/ CC/ RCC

surface and the cost of bolts etc. The pipes shall be fixed to the

already fixed brackets with the help of 30 mm x1.6 mm galvanised

M.S. flats of specified shape and of total length 420 mm and shall be

fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on

each side of the pipe.

a) 17.77.3 Total bracket length 1040 mm of approved shape and design (for Each 10 451.90 4519.00

three 100 mm dia pipes)

TOTAL FOR DRAINAGE 393780.60 5797297.33

Digitally signed by

PRADYUMNA MUKHERJEE

DESCRIPTION Rate

I.NO DSR CODE UNITS BOQ Qty DSR AMOUNT NDSR AMOUNT

The Main table shall be of size 3600 Width mm x 1080 mm Depth x 750 mm height. Top surface of the table shall 4,82,817.15

made up of commercial Ply duly finished with Veneer and final coating of PU. The Main desk should contain in

Smart Case - space slides effortlessly in style.The mobile Pedestal shall be of size 480 Width mm x 640 Depth mm

CMD room x 600 Height mm. Mobile pedestal shall be coated of commercial ply with veneer coating and PU coating.The

main table ERU Top shall be of commercial ply duly finished with veneer and final PU coating. Size of ERU top 1900 Width

mm x 480 Depth mm x 550(not from ground with castors).The main desk is provided eith the wire management

system also there is perfect storage side unit .

The Size of the Back unit shall be made up of commercial ply duly finished with veneer & final finish by PU 24,748.00

coating , laqured glass , louver. Below storage shall be provided with wooden shutters & the upper left & right

side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass

2 Backunit Sqm 9 2,22,732.00

of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H. with provision for

furniture lighting customized

HIGH BACK CHAIR FOR CABIN 1,00,682.50

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT HIGH BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for 25%

compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam

with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 76.7 cm. (D) ARMRESTS: The

armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast

Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-Down adjustment has 8

position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width

adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm

range).Armrest top is made up of high density PU molded over glass filled Poly-amide inner.POSTURE PERFECT

MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type.

3 Main chair Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3- Each 1 1,00,682.50

position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated

with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish

die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position.

It can be adjusted in the range of 7.5+0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height adjustment has an adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-

cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-

center dia. TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU

lining, having 6.50.1cm wheel Diameter and assembled to pedestal.

Digitally signed by

PRADYUMNA MUKHERJEE

VISITOR CHAIR FOR CABIN 80,129.00

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT FULL BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for 25%

compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam

with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 61.8 cm. (D) ARMRESTS: The

armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast

Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-Down adjustment has 8

position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width

adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm

range).Armrest top is made up of high density PU molded over glass filled Poly-amide inner.POSTURE PERFECT

MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type.

4 Visitor Chair Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3- Each 4 3,20,516.00

position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated

with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish

die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position.

It can be adjusted in the range of 7.5+0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height adjustment has an adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-

cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-

center dia. TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU

lining, having 6.50.1cm wheel Diameter and assembled to pedestal.

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery -Pigmented 89,389.50

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid

wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

5 initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , Each 1 89,389.50

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Providing and placing sofa of size 1020mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented 53,774.00

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame

Waiting Sofa with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to

1 seater enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch

, Zigzag Spring - 3.8mm

Comfort- The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with

sinking feeling.

Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.

Overall size of 1200mm(L)1000mm(D)x450mm(H)Designed for the modern minimalist with a need for handy, 41,091.80

7 center Table compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown Each 1 41,091.80

construction built for longevity.

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern minimalist with a need for handy, 16,675.00

8 Side Table compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown Each 2 33,350.00

construction built for longevity.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery -Pigmented 89,389.50

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid

wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

9 Sofa 3 seater initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , Each 2 1,78,779.00

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Overall size of 1000mm(L)1000mm(D)x450mm(H)Designed for the modern minimalist with a need for handy, 29,591.80

10 center Table compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown Each 1 29,591.80

construction built for longevity.

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern minimalist with a need for handy, 16,675.00

11 Side Table compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown Each 2 33,350.00

construction built for longevity.

Dinning Room -

The Dinning table shall be of size 1800 Width mm x 1080 mm Depth x 750 mm height. Top surface of the table

12 Dinning Table shall made up of commercial board duly finished with stone top..Theside anf legs shall be of hard wood PU Each 1 97,129.00 97,129.00

coating. Customized

Supplying and placing of chair of dimensions 635W x 630D x 800H mm. The seat height shall be 455mm.The back

shell shall be made of 15mm plywood panle connected using Brackets made from 3mm Hot Rolled Steel Plates .

Steel brackets are Epoxy Polyester Powder Coated. 25mm PU Slab -Stock foam is pasted onto both sides of the

shell and pinched together to achieve the radius along the periphery. It shall be upholstered in Leatherette /

fabric. The seat cushion shall be made using 50mm PU Slab-stock foam and is upholstered in Leatherette. It shall

13 Dinning Chair Each 6 32,200.00 1,93,200.00

be held in place with Hook and Loop tape stitched to its bottom side. The understructure shall be made of

seasoned Tewak Wood finished witrh clear matt coat of PU Lacquer. Undrstrucutre members shall be glued

together using Epoxy Resin Based Adhesive. The shell is fixed to the understructure using Alloy steel hardware

(blackened and coated with rust preventive oil).

B Director OFFICE - -

The Main table shall be of size 3600 Width mm x 1080 mm Depth x 750 mm height. Top surface of the table shall

made up of commercial ply duly finished with Veneer and final coating of PU. The Main desk should contain in

Smart Case - space slides effortlessly in style.The mobile Pedestal shall be of size 480 Width mm x 640 Depth mm

Director main x 600 Height mm. Mobile pedestal shall be coated of commercial with veneer coating and PU coating.The ERU

table Top shall be ofcommercial ply duly finished with veneer and final PU coating. Size of ERU top 1900 Width mm x

480 Depth mm x 550(not from ground with castors).The main desk is provided eith the wire management system

also there is perfect storage side unit .

The Size of the Back unit shall be made up of commercial ply duly finished with veneer & final finish by PU

coating , laqured glass , louver. Below storage shall be provided with wooden shutters & the upper left & right

side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass

of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H. with provision for

furniture lighting customized

Digitally signed by

PRADYUMNA MUKHERJEE

HIGH BACK CHAIR FOR CABIN

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT HIGH BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for 25%

compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam

with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 76.7 cm. (D) ARMRESTS: The

armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast

Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-Down adjustment has 8

position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width

adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm

range).Armrest top is made up of high density PU molded over glass filled Poly-amide inner.POSTURE PERFECT

MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type.

3 Main chair Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3- Each 1 1,00,682.50 1,00,682.50

position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated

with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish

die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position.

It can be adjusted in the range of 7.5+0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height adjustment has an adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-

cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-

center dia. TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU

lining, having 6.50.1cm wheel Diameter and assembled to pedestal.

Digitally signed by

PRADYUMNA MUKHERJEE

VISITOR CHAIR FOR CABIN

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT FULL BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for 25%

compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam

with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 61.8 cm. (D) ARMRESTS: The

armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast

Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-Down adjustment has 8

position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width

adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm

range).Armrest top is made up of high density PU molded over glass filled Poly-amide inner.POSTURE PERFECT

MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type.

4 Visitor Chair Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3- Each 4 90,129.00 3,60,516.00

position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated

with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish

die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position.

It can be adjusted in the range of 7.5+0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height adjustment has an adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-

cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-

center dia. TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU

lining, having 6.50.1cm wheel Diameter and assembled to pedestal.

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid

wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

5 initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , Each 1 89,389.50 89,389.50

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Providing and placing sofa of size 1520mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aestheticsS Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood

frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

6 initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , Each 1 75,693.00 75,693.00

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling.Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and placing sofa of size 1020mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood

frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

7 initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , Each 2 53,774.00 1,07,548.00

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Overall size of 1200mm(L)1000mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

8 Center Table compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown Each 1 41,091.80 41,091.80

construction built for longevity.

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

9 Side Table compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown Each 2 16,675.00 33,350.00

construction built for longevity.

Ante /Dinning room - -

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery -Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid

wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

10 initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , Each 1 89,389.50 89,389.50

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Overall size of 1000mm(L)1000mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

11 Center Table compartmentalized storage.• Table top of durable,vineeered with pu finish , modern look.• A strong, Each 1 29,591.80 29,591.80

knockdown construction built for longevity.

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

12 Side Table compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown Each 1 16,675.00 16,675.00

construction built for longevity.

The Dinning table shall be of size 1500 Width mm x 900 mm Depth x 750 mm height. Top surface of the table

13 Dinning Table shall made up of commercial ply duly finished with stone top..Theside anf legs shall be of hard wood PU coating. Each 1 85,629.00 85,629.00

Supplying and placing of chair of dimensions 635W x 630D x 800H mm. The seat height shall be 455mm.The back

shell shall be made of 15mm plywood panle connected using Brackets made from 3mm Hot Rolled Steel Plates .

Steel brackets are Epoxy Polyester Powder Coated. 25mm PU Slab -Stock foam is pasted onto both sides of the

shell and pinched together to achieve the radius along the periphery. It shall be upholstered in Leatherette /

fabric. The seat cushion shall be made using 50mm PU Slab-stock foam and is upholstered in Leatherette. It shall

14 Dinning Chair Each 4 32,200.00 1,28,800.00

be held in place with Hook and Loop tape stitched to its bottom side. The understructure shall be made of

seasoned Tewak Wood finished witrh clear matt coat of PU Lacquer. Undrstrucutre members shall be glued

together using Epoxy Resin Based Adhesive. The shell is fixed to the understructure using Alloy steel hardware

(blackened and coated with rust preventive oil).

C COO OFFICE - -

Digitally signed by

PRADYUMNA MUKHERJEE

The Main table shall be of size 3000 Width mm x 1080 mm Depth x 750 mm height. Top surface of the table shall

made up of commercial ply duly finished with Veneer and final coating of PU. The Main desk should contain in

Smart Case - space slides effortlessly in style.The mobile Pedestal shall be of size 480 Width mm x 640 Depth mm

x 600 Height mm. Mobile pedestal shall be coated of commercial ply with veneer coating and PU coating.The

ERU Top shall be ofcommercial ply duly finished with veneer and final PU coating. Size of ERU top 1900 Width

mm x 480 Depth mm x 550(not from ground with castors).The main desk is provided eith the wire management

system also there is perfect storage side unit .

The Size of the Back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating ,

laqured glass , louver. Below storage shall be provided with wooden shutters & the upper left & right side of the

2 Backunit back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass of Sqm 6 24,748.00 1,48,488.00

minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H. with provision for

furniture lighting customized

HIGH BACK CHAIR FOR CABIN

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT HIGH BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for 25%

compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam

with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 76.7 cm. (D) ARMRESTS: The

armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast

Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-Down adjustment has 8

position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width

adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm

range).Armrest top is made up of high density PU molded over glass filled Poly-amide inner.POSTURE PERFECT

MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type.

3 Main chair Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3- Each 1 65,780.00 65,780.00

position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated

with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish

die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position.

It can be adjusted in the range of 7.5+0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height adjustment has an adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-

cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-

center dia. TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU

lining, having 6.50.1cm wheel Diameter and assembled to pedestal.

Digitally signed by

PRADYUMNA MUKHERJEE

VISITOR CHAIR FOR CABIN

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT FULL BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for 25%

compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam

with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 61.8 cm. (D) ARMRESTS: The

armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast

Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-Down adjustment has 8

position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width

adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm

range).Armrest top is made up of high density PU molded over glass filled Poly-amide inner.POSTURE PERFECT

MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type.

4 Visitor Chair Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3- Each 3 62,790.00 1,88,370.00

position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated

with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish

die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position.

It can be adjusted in the range of 7.5+0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height adjustment has an adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-

cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-

center dia. TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU

lining, having 6.50.1cm wheel Diameter and assembled to pedestal.

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame

Waiting Sofa with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to

3 seatet enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch

, Zigzag Spring - 3.8mm

Comfort- The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with

sinking feeling.

Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.

Providing and placing sofa of size 1020mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame

Waiting Sofa with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to

1 seater enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch

, Zigzag Spring - 3.8mm

Comfort- The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with

sinking feeling.

Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.

Overall size of 1000mm(L)1000mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

7 center Table compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown Each 1 29,591.80 29,591.80

construction built for longevity.

Digitally signed by

PRADYUMNA MUKHERJEE

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

8 Side Table compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown Each 2 16,675.00 33,350.00

construction built for longevity.

The Dinning table shall be of size 1500 Width mm x 1080 mm Depth x 750 mm height. Top surface of the table

9 Dinning Table shall made up of commercial ply duly finished with stone top..Theside anf legs shall be of hard wood PU coating. Each 1 85,629.00 85,629.00

Supplying and placing of chair of dimensions 635W x 630D x 800H mm. The seat height shall be 455mm.The back

shell shall be made of 15mm plywood panle connected using Brackets made from 3mm Hot Rolled Steel Plates .

Steel brackets are Epoxy Polyester Powder Coated. 25mm PU Slab -Stock foam is pasted onto both sides of the

shell and pinched together to achieve the radius along the periphery. It shall be upholstered in Leatherette /

fabric. The seat cushion shall be made using 50mm PU Slab-stock foam and is upholstered in Leatherette. It shall

10 Dinning Chair Each 4 32,200.00 1,28,800.00

be held in place with Hook and Loop tape stitched to its bottom side. The understructure shall be made of

seasoned Tewak Wood finished witrh clear matt coat of PU Lacquer. Undrstrucutre members shall be glued

together using Epoxy Resin Based Adhesive. The shell is fixed to the understructure using Alloy steel hardware

(blackened and coated with rust preventive oil).

D E9 Cabin - -

Providing and Placing Main TAble of Size 2400x1000x750.MAIN WORKTOP Size 2400x900x740, ERU

1200x450x610mm- Main worktop - Made of 43mm Thick (±1) combination of commercial ply and particle board

with top veneer face coated with clear lacquer. All edges are edge banded with matching 1mm thick veneer

lipping.LEATHER PAD:Made of 18mm Thick (±1) commercial ply with Leatherette wrapped around top surface.

This leather pad is fixed to main top panel.DRAWER UNIT:Top panel and drawer unit modesty panel is made of

43mm Thick (±1) combination ofcommercial ply and particle board with top veneer face coated with clear

lacquer. All thickness edges are edge banded with matching lipping.Remaining construction is of 18mm Pre-

laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with

matching 2 mm thick PVC lipping. Bottom panel of drawer is 9mm thick particle board with leatherette on top

surface.Drawer unit is provided with soft closing channels for smooth opening and closing.Drawer unit is secured

with side central lock.OPEN STORAGE UNIT:Top panel and open storage unit modesty panel is made of 43mm

Thick (±1) combination of commercial ply and particle board with top veneer face coated with clear lacquer. All

thickness edges are edge banded with matching lipping.Remaining construction is of 18mm Pre-laminated twin

board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm

thick PVC lipping.MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved

shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty is fitted with

aluminum trims.UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and

approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Door is fixed

with soft closing hinges and handle is provided for ease of opening.Also lock is provided on side panel for

security.ACCESS FLAP WITH POWER BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2

USB power points, 1 HDMI connection, 1 inbuilt misc. cable grommet and CAT 3 and CAT 6 connections.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and placing Back unit of size 2400mm(L)x470mm(D)x2325mm(H).CONSTRUCTION AND MATERIAL:

Made from combination of Top panel(0.5mm CRCA), side panel(0.5mm CRCA), Bottom panel(0.5mm CRCA for

600W and 0.8mm CRCA for 1200W), Back panel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and End

Cover(0.5mm CRCA). Shelves are 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513). 4 nos of shelves

for 1950H and 5 nos of shelves for 2325H back unit. Storage body is powder coated with Epoxy Polyester to the

thickness of 50 microns (+/-10 micron).VENEER DOOR: Made of 12mm Thick (±1) commercial ply with 3.5mm

veneer both side and face coated with clear lacquer. All edges are edge banded with matching 1mm thick veneer

lipping. Door is provided with soft closing hinge. Handle is also provided for ease of opening. Storage is secured

with 3 way cam lock.GLASS DOOR: Made from the combination of aluminium alloy (63400) extrusion and 4mm

clear toughened glass. Aluminium extrusion of glass doors are powder coated with Epoxy Polyester to the

thickness of 50 microns (+/-10 micron). Handle is provided for ease of

opening. RH Glass Door is provided with 3 way cam lock for security. as customised

Providing & placing high back chair.SEAT ASSEMBLY :

The seat is made up of 12mm thick MR Grade plywood, layered with pocket spring core, super soft foam of 32

kg/m3 density and edging foam of 28 kg/m3 density. A 200GSM soft touch fibre fill sheet is placed over foam sub-

assembly and upholstered in natural leather or leatherette.BACK ASSEMBLY :

The back assembly is made up of a gombination of pinewood members, 12mm thick MR Grade plywood and

2mm thick cardboard, layered with slab stock foam of 28 kg/m3 density. A 200GSM soft touch fibre fill sheet is

placed over foam sub-assembly and upholstered in natural leather or leatherette.ARMPAD ASSEMBLY :

The armpad assembly is made up of 6mm thick MR Grade plywood fixed with MS powder-coated brackets,

layered with foam of 60 kg/m3 density. A 200GSM soft touch fibre fill sheet is placed over foam sub-assembly

and upholstered in natural leather or leatherette.4. CENTER TILT WITH MULTI POSITION LOCK MECHANISM: The

3 Main chair mechanism is designed with the following features: Each 8 65,349.90 5,22,799.20

360° revolving type

3 position locking

Tilt tension adjustmentPNEUMATIC HEIGHT ADJUS/MENT: The Class 4 pneumatic height adjustment has ar

stroke of 10 ÷ 0.3 cm.6. PEDESTAL ASSEMBLY :

The pedestal is made of high-pressure die-cast polished aluminum with a buffed outside surface and black color-

coated internal surface. It is fitted with 5 castors and has a pitch-center diameter of 67.5#0.5 cm (77.51.0 cm

7. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black polyamide.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing & placing mid back chair.SEAT ASSEMBLY :

The seat is made up of 12mm thick MR Grade plywood, layered with pocket spring core, super soft foam of 32

kg/m3 density and edging foam of 28 kg/m3 density. A 200GSM soft touch fibre fill sheet is placed over foam sub-

assembly and upholstered in natural leather or leatherette.BACK ASSEMBLY :

The back assembly is made up of a gombination of pinewood members, 12mm thick MR Grade plywood and

2mm thick cardboard, layered with slab stock foam of 28 kg/m3 density. A 200GSM soft touch fibre fill sheet is

placed over foam sub-assembly and upholstered in natural leather or leatherette.ARMPAD ASSEMBLY :

The armpad assembly is made up of 6mm thick MR Grade plywood fixed with MS powder-coated brackets,

layered with foam of 60 kg/m3 density. A 200GSM soft touch fibre fill sheet is placed over foam sub-assembly

and upholstered in natural leather or leatherette.4. CENTER TILT WITH MULTI POSITION LOCK MECHANISM: The

4 Visitor Chair mechanism is designed with the following features: Each 24 35,755.15 8,58,123.60

360° revolving type

3 position locking

Tilt tension adjustmentPNEUMATIC HEIGHT ADJUS/MENT: The Class 4 pneumatic height adjustment has ar

stroke of 10 ÷ 0.3 cm.6. PEDESTAL ASSEMBLY :

The pedestal is made of high-pressure die-cast polished aluminum with a buffed outside surface and black color-

coated internal surface. It is fitted with 5 castors and has a pitch-center diameter of 67.5#0.5 cm (77.51.0 cm

7. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black polyamide.

Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shallbe 1820W x 905D x 855H.

The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft

PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The

back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam

of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1

cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of

cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is

mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel

(grade SS 202) tube & plate with plastic endcap.

Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shallbe 1460W x 905D x 855H.

The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft

PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The

back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam

of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1

cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of

cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is

mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel

(grade SS 202) tube & plate with plastic endcap.

Overall size of 1000mm(L)1000mm(D)x450mm(H)Designed for the modern

minimalist with a need for handy, compartmentalized storage.• Tabletop of durable, toughened glass with a

7 Center table digitally back-printed Skyline pattern creates a sleek, modern look.• A strong, knockdown construction built for Each 8 27,291.80 2,18,334.40

Digitally signed by

PRADYUMNA MUKHERJEE

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern

minimalist with a need for handy, compartmentalized storage.• Tabletop of durable, toughened glass with a

digitally back-printed Skyline pattern creates a sleek, modern look.• A strong, knockdown construction built for

Providing in place of main table with overall size of table equal to 1200 x 750 x750mm. The table is made of 25

mm thick Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet

provided on work surface for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin

Board of E1-P2 grade. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

9 Dinning Table Each 8 28,064.60 2,24,516.80

approved shade edge banded with matching 2 mm thick PVC lipping. The HInge door unit is made of 25 mm thick

Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made

up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester

mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-

51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is

having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in

aluminium structure of armrest which is connected to aluminium back spine and is operated with button.

Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio Synchro Mechanism. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with

feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing

10 Dinning Chair Each 32 22,207.65 7,10,644.80

should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic

height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of

Chair - 70.5 cm as measured from pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions

tolerance / variations shall be within +/- 1 cm.

E PS Cabin e9 , coo ,director , md - -

Digitally signed by

PRADYUMNA MUKHERJEE

Providing in place of main table with overall size of table 1650 x 1550 x 750mm. The main table shall be of size

1650 x 750 x 750mm. The side unit shall be 1200 x 500 x 750mm. The table is made of 25 mm thick commercial

ply – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top.

Soft closing access flap within-build power box are provided on work surface for wire management. The ERU top

is made of 25 mm thick commercial ply one side pre-laminate board confirming to IS-14587:1998 with 0.4mm

PVC membrane pressed on to top. The modesty panel is made of 25 mm thick commercial ply one side pre-

laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure

is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with

matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade

and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick

commercial ply one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal

construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer

extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of

opening. Pedestals are provided with lock for security.

Supplying of side storage unit of officers having dimension 1190WX 450DX 740H:Overall size of hinge door unit is

1190(H)x740mm (h)x450 mm (D). Providing and placement of back storages with : CONSTRUCTION & MATERIAL

Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal

cladding of 1.0 mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyester

powder of 50±10 microns thickness. TOP OPTIONS- The Storage units are provided with 11mm thk bent metal

tops made of 1.0 mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±

10 microns thickness. DOOR & DOOR OPENING two door opening for all other width of 1150 W.The doors are

made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the

other side. SHELVING- Height wise adjustable shelf mounting holes provided on side panels for easy interchange

of shelf height as required. Fixed shelves along with adjustable shelves provided only in case of 4.0 feet height

units. No fixed shelves for 2.5 feet height storage units. Uniformly distributed load capacity for each shelf is 40kg

2 backunit maximum. SKIRTING OPTION- The skirting units are provided with 150mm high skirting made of 1.0 mm thick Each 28 18,386.20 5,14,813.60

C.R.C.A(as per IS:513) and is coated with Epoxy polyester powder of 50+-10 micros thickness. LEVELER-Screw

type adjustable leverer with plastic base provides vertical adjustment for floor unevenness and levelling of

units.BACK PANELS Back panels are made of 18mm thick pre-laminated boards with options of decorative as well

as fabric finishes. 2.5 height units consists of single back panel whereas 4.0 height and 4.5 height units consist of

split back top panel and split back bottom panels separated by an Aluminium extrusion. LOCKING MECHANISM-

3-way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE-

Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing.The

OEM should be ISO 9001:2015,ISO 14001:2015 & ISO 18001:2007 certified.

Digitally signed by

PRADYUMNA MUKHERJEE

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made

up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester

mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-

51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is

having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in

aluminium structure of armrest which is connected to aluminium back spine and is operated with button.

Armtop is made up of PU molded over plastic inner. The mechanism shall be Active BioSynchro Mechanism. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with

feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing

should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic

3 Main Chair height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished 14 24,048.80 3,36,683.20

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. The neckrest assembly consists of upholstered neckrest inner(material-

poly propylene) with moulded polyurethane foam and polyster fabric. upholstered inner shall be fixed to neck

rest cover. neckrest shall be fixed to back assembly through neckrest spline. Overall dimensions of Chair shall be,

Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min

109.3 to max 124.4 cm. Seat height - min 45.5cm to max 55.5cm. Dimensions tolerance / variations shall be

within +/- 1 cm.

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made

up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester

mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-

51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is

having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in

aluminium structure of armrest which is connected to aluminium back spine and is operated with button.

Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio Synchro Mechanism. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with

feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing

should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic

height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of

Chair - 70.5 cm as measured from pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions

tolerance / variations shall be within +/- 1 cm.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and Placing Main TAble of Size 2000x2100x750.MAIN WORKTOP Size 2400x900x740, ERU

1200x450x610mm- Main worktop - Made of 43mm Thick (±1) combination of commercial ply and particle board

with top veneer face coated with clear lacquer. All edges are edge banded with matching 1mm thick veneer

lipping.LEATHER PAD:Made of 18mm Thick (±1) commercial ply with Leatherette wrapped around top surface.

This leather pad is fixed to main top panel.DRAWER UNIT:Top panel and drawer unit modesty panel is made of

43mm Thick (±1) combination of commercial ply and particle board with top veneer face coated with clear

lacquer. All thickness edges are edge banded with matching lipping.Remaining construction is of 18mm Pre-

laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with

matching 2 mm thick PVC lipping. Bottom panel of drawer is 9mm thick particle board with leatherette on top

surface.Drawer unit is provided with soft closing channels for smooth opening and closing.Drawer unit is secured

with side central lock.OPEN STORAGE UNIT:Top panel and open storage unit modesty panel is made of 43mm

Thick (±1) combination of commercial ply and particle board with top veneer face coated with clear lacquer. All

thickness edges are edge banded with matching lipping.Remaining construction is of 18mm Pre-laminated twin

board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm

thick PVC lipping.MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved

shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty is fitted with

aluminum trims.UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and

approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Door is fixed

with soft closing hinges and handle is provided for ease of opening.Also lock is provided on side panel for

security.ACCESS FLAP WITH POWER BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2

USB power points, 1 HDMI connection, 1 inbuilt misc. cable grommet and CAT 3 and CAT 6connections.

The Back Unit shall be . It shall be made of 25mm thick MDF – one side pre-laminate board confirming to IS-

14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm thick Pre-

2 Backunit laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Sqm 80 22,273.20 17,81,856.00

Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is

provided with lock for security. customised

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and Placing in Position High Back Chair. The cushioned seats shall be made of injection moulded plastic

outer and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane

foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall

be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS

ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm

W x 77 cm D. The armrest top shall be moulded from polurethane, and shall be upholstered with pure leather

and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm

thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5

steps. The adjustable tilting mechanism shall be designed with the following features : 360° revolving type, front-

pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort, Tilt tension

adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt angle to the

chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black powder coated.

Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat depth adjustment range

shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism housed in plastic T spine. It can

be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic

height adjustment shall have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast

polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre

dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and

assembled to pedestal.

Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5-114cm.

Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic outer and

inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof

Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6

cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW

round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. The armrest top shall be

moulded from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable

type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome

plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism

shall be designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground

and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating

4 Visitor Chair Each 48 35,530.45 17,05,461.60

position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be

integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back

frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the range of

7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall

have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and

fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel

castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

Digitally signed by

PRADYUMNA MUKHERJEE

Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x 855H.

The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft

PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The

back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam

Waiting Sofa of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1

2 seator cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of

cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is

mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel

(grade SS 202) tube & plate with plastic endcap.

Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H.

The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft

PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The

back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam

Waiting Sofa of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1

1 seator cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of

cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is

mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel

(grade SS 202) tube & plate with plastic endcap.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for

fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per

7 Center table Each 16 15,114.45 2,41,831.20

IS:1762. overall dimensions of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern

minimalist with a need for handy, compartmentalized storage.• Tabletop of durable, toughened glass with a

digitally back-printed Skyline pattern creates a sleek, modern look.• A strong, knockdown construction built for

Providingin place of main table with overall size of table 1800 x 1800 x 750mm. The main table shall be of size

1800 x 900 x 750mm. The side unit shall be 1200 x 500 x 750mm. The table is made of 25 mm thick MDF – one

side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing

access flap within-build power box are provided on work surface for wire management. The ERU top is made of

25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed

on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-

14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-

laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping.

The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board

with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder

coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti

slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Digitally signed by

PRADYUMNA MUKHERJEE

The Back Unit shall be of dimensions 1800 x 500 x 750mm. It shall be made of 25mm thick MDF – one side pre-

laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit

is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with

matching 2 mm thick PVC lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for

ease of opening. Storage is provided with lock for security.

Providing and Placing in Position High Back Chair. The cushioned seats shall be made of injection moulded plastic

outer and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane

foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall

be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS

ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm

W x 77 cm D. The armrest top shall be moulded from polurethane, and shall be upholstered with pure leather

and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm

thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5

steps. The adjustable tilting mechanism shall be designed with the following features : 360° revolving type, front-

pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort, Tilt tension

adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt angle to the

chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black powder coated.

Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat depth adjustment range

shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism housed in plastic T spine. It can

be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic

height adjustment shall have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast

polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre

dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and

assembled to pedestal.

Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5-114cm.

Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic outer and

inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof

Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6

cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW

round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. The armrest top shall be

moulded from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable

type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome

plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism

shall be designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground

and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating

4 Visitor Chair Each 64 35,530.45 22,73,948.80

position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be

integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back

frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the range of

7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall

have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and

fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel

castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

Digitally signed by

PRADYUMNA MUKHERJEE

Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x 855H.

The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft

PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The

back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam

Waiting 2 of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1

Seater Sofa cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of

cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is

mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel

(grade SS 202) tube & plate with plastic endcap.

Supplying of side storage unit of officers having dimension 1050WX 450DX 740H:Overall size of hinge door unit is

1190(H)x740mm (h)x450 mm (D). Providing and placement of back storages with : CONSTRUCTION & MATERIAL

Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal

cladding of 1.0 mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyester

powder of 50±10 microns thickness. TOP OPTIONS- The Storage units are provided with 11mm thk bent metal

tops made of 1.0 mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±

10 microns thickness. DOOR & DOOR OPENINGtwo door opening for all other width of 1050 W.The doors are

made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the

other side. SHELVING- Height wise adjustable shelf mounting holes provided on side panels for easy interchange

of shelf height as required. Fixed shelves along with adjustable shelves provided only in case of 4.0 feet height

units. No fixed shelves for 2.5 feet height storage units. Uniformly distributed load capacity for each shelf is 40kg

6 Side Storage maximum. SKIRTING OPTION- The skirting units are provided with 150mm high skirting made of 1.0 mm thick Each 32 1,16,774.45 37,36,782.40

C.R.C.A(as per IS:513) and is coated with Epoxy polyester powder of 50+-10 micros thickness. LEVELER-Screw

type adjustable leverer with plastic base provides vertical adjustment for floor unevenness and levelling of

units.BACK PANELS Back panels are made of 18mm thick pre-laminated boards with options of decorative as well

as fabric finishes. 2.5 height units consists of single back panel whereas 4.0 height and 4.5 height units consist of

split back top panel and split back bottom panels separated by an Aluminium extrusion. LOCKING MECHANISM-

3-way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE-

Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing.The

OEM should be ISO 9001:2015,ISO 14001:2015 & ISO 18001:2007 certified.

Supplying of Recta workstation of size 1500 X 1600x 750 with KBPT with ERU 900X750mm with cubicle partion

.Providing DESK based modular workstation with worktop thickness 25mm System ht - 750 mm

.Understructure - The slanted legs with perforated metal modesty in between are connected to the

understructure with the help of PDC Connectors to provide a stable and sturdy base for the worktops. Modesty

panel shall be of Metal 1.2 mm thick CRCA. Wire Management : Metal powder coated power box with wire

raiser+D56 is given to pull wires from the floor junction box upto the power box fixed under neath the worktop.

Aluminium access flaps on worktop above power box cut out for accessing switches.Worktop mounted metal

modesty made from 0.8 mm thk CRCA (IS: 513) is provided.Worksurface - out of 25 mm thk prelam particle

board with flat pvc lipping edge banding of size 1500 mm w x 600 mm d.Pedestals - Nova pedestal flat metal

front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The

product should be GREENPRO, SCS IAQ, GRIHA, BIFMA certified.

Digitally signed by

PRADYUMNA MUKHERJEE

Supplying of side storage unit of officers having dimension 1050WX 450DX 740H:Overall size of hinge door unit is

1190(H)x740mm (h)x450 mm (D). Providing and placement of back storages with : CONSTRUCTION & MATERIAL

Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal

cladding of 1.0 mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyester

powder of 50±10 microns thickness. TOP OPTIONS- The Storage units are provided with 11mm thk bent metal

tops made of 1.0 mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±

10 microns thickness. DOOR & DOOR OPENINGtwo door opening for all other width of 1050 W.The doors are

made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the

other side. SHELVING- Height wise adjustable shelf mounting holes provided on side panels for easy interchange

of shelf height as required. Fixed shelves along with adjustable shelves provided only in case of 4.0 feet height

units. No fixed shelves for 2.5 feet height storage units. Uniformly distributed load capacity for each shelf is 40kg

2 Side Storage maximum. SKIRTING OPTION- The skirting units are provided with 150mm high skirting made of 1.0 mm thick Each 35 16,520.90 5,78,231.50

C.R.C.A(as per IS:513) and is coated with Epoxy polyester powder of 50+-10 micros thickness. LEVELER-Screw

type adjustable leverer with plastic base provides vertical adjustment for floor unevenness and levelling of

units.BACK PANELS Back panels are made of 18mm thick pre-laminated boards with options of decorative as well

as fabric finishes. 2.5 height units consists of single back panel whereas 4.0 height and 4.5 height units consist of

split back top panel and split back bottom panels separated by an Aluminium extrusion. LOCKING MECHANISM-

3-way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE-

Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing.The

OEM should be ISO 9001:2015,ISO 14001:2015 & ISO 18001:2007 certified.

The Back Unit shall be of dimensions 1800 x 500 x 750mm. It shall be made of 25mm thick MDF – one side pre-

laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit

is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with

3 back storage Each 35 53,928.10 18,87,483.50

matching 2 mm thick PVC lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for

ease of opening. Storage is provided with lock for security.

Digitally signed by

PRADYUMNA MUKHERJEE

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made

up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester

mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-

51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is

having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in

aluminium structure of armrest which is connected to aluminium back spine and is operated with button.

Armtop is made up of PU molded over plastic inner. The mechanism shall be Active BioSynchro Mechanism. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with

feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing

should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic

4 Main chair height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished Each 35 20,048.80 7,01,708.00

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. The neckrest assembly consists of upholstered neckrest inner(material-

poly propylene) with moulded polyurethane foam and polyster fabric. upholstered inner shall be fixed to neck

rest cover. neckrest shall be fixed to back assembly through neckrest spline. Overall dimensions of Chair shall be,

Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min

109.3 to max 124.4 cm. Seat height - min 45.5cm to max 55.5cm. Dimensions tolerance / variations shall be

within +/- 1 cm.

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made

up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester

mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-

51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is

having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in

aluminium structure of armrest which is connected to aluminium back spine and is operated with button.

Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio Synchro Mechanism. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with

feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing

5 Visitor Chair Each 70 15,207.65 10,64,535.50

should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic

height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of

Chair - 70.5 cm as measured from pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions

tolerance / variations shall be within +/- 1 cm.

Digitally signed by

PRADYUMNA MUKHERJEE

Supplying of Recta workstation of size 1500 X 1600x 750 with KBPT .Providing DESK based modular

workstation with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with

perforated metal modesty in between are connected to the understructure with the help of PDC Connectors to

provide a stable and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Wire

Management : Metal powder coated power box with wire raiser+D56 is given to pull wires from the floor

junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above

power box cut out for accessing switches.Worktop mounted metal modesty made from 0.8 mm thk CRCA (IS:

513) is provided.Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size

1500 mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390

mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product should be GREENPRO, SCS IAQ, GRIHA, BIFMA

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made

up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester

mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-

51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is

having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in

aluminium structure of armrest which is connected to aluminium back spine and is operated with button.

Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio Synchro Mechanism. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with

feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing

should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic

height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of

Chair - 70.5 cm as measured from pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions

tolerance / variations shall be within +/- 1 cm.

Digitally signed by

PRADYUMNA MUKHERJEE

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made

up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester

mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-

51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is

having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in

aluminium structure of armrest which is connected to aluminium back spine and is operated with button.

Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio Synchro Mechanism. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with

feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing

3 Visitor Chair Each 130 10,706.20 13,91,806.00

should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic

height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of

Chair - 70.5 cm as measured from pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions

tolerance / variations shall be within +/- 1 cm.

Supplying of Recta workstation of size 1500 X 600x 750 with KBPT .Providing DESK based modular workstation

with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with perforated metal

modesty in between are connected to the understructure with the help of PDC Connectors to provide a stable

and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Wire Management :

Metal powder coated power box with wire raiser+D56 is given to pull wires from the floor junction box upto the

power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for

4 back storage Each 65 62,241.45 40,45,694.25

accessing switches.Worktop mounted metal modesty made from 0.8 mm thk CRCA (IS: 513) is

provided.Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500

mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm

w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product should be GREENPRO, SCS IAQ, GRIHA, BIFMA

Supplying of Recta workstation of size 1500 X 600x 750 with KBPT .Providing DESK based modular workstation

with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with perforated metal

modesty in between are connected to the understructure with the help of PDC Connectors to provide a stable

and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Wire Management :

Metal powder coated power box with wire raiser+D56 is given to pull wires from the floor junction box upto the

power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for

accessing switches.Worktop mounted metal modesty made from 0.8 mm thk CRCA (IS: 513) is

provided.Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500

mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm

w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product should be GREENPRO, SCS IAQ, GRIHA, BIFMA

Digitally signed by

PRADYUMNA MUKHERJEE

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made

up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester

mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-

51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is

having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in

aluminium structure of armrest which is connected to aluminium back spine and is operated with button.

Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio Synchro Mechanism. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with

feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing

should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic

height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of

Chair - 70.5 cm as measured from pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions

tolerance / variations shall be within +/- 1 cm.

Supplying of Recta workstation of size 1500 X 600x 750 with KBPT .Providing DESK based modular workstation

with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with perforated metal

modesty in between are connected to the understructure with the help of PDC Connectors to provide a stable

and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Wire Management :

Metal powder coated power box with wire raiser+D56 is given to pull wires from the floor junction box upto the

power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for

accessing switches.Worktop mounted metal modesty made from 0.8 mm thk CRCA (IS: 513) is

provided.Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200

mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm

w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product should be GREENPRO, SCS IAQ, GRIHA, BIFMA

Digitally signed by

PRADYUMNA MUKHERJEE

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made

up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester

mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-

51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is

having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in

aluminium structure of armrest which is connected to aluminium back spine and is operated with button.

Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio Synchro Mechanism. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with

feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing

should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic

height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of

Chair - 70.5 cm as measured from pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions

tolerance / variations shall be within +/- 1 cm.

Supplying of Recta workstation of size 1200 X 600x 750 with KBPT .Providing DESK based modular workstation

with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with perforated metal

modesty in between are connected to the understructure with the help of PDC Connectors to provide a stable

and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Wire Management :

Metal powder coated power box with wire raiser+D56 is given to pull wires from the floor junction box upto the

power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for

accessing switches.Worktop mounted metal modesty made from 0.8 mm thk CRCA (IS: 513) is

provided.Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200

mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm

w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product should be GREENPRO, SCS IAQ, GRIHA, BIFMA

Digitally signed by

PRADYUMNA MUKHERJEE

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made

up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester

mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-

51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is

having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in

aluminium structure of armrest which is connected to aluminium back spine and is operated with button.

Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio Synchro Mechanism. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with

feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing

should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic

height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of

Chair - 70.5 cm as measured from pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions

tolerance / variations shall be within +/- 1 cm.

Providing and Placing in position Conference table for 24 seater having 12 Nos of 2 Seater Modules of size

1350mm X 600mm X 740mm . Worktop- Made of 25mm thick MDF-one side pre-laminate board conforming to

IS-14587:1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge.Plastic ABS access flap

is provided for easy access to wires and cables.Modesty consist of 18mm Thick Pre-laminated twin board of E1-

P2 grade and approved shadeconforming to IS-12823:1990, Aluminium alloy 63400 - WP profile is used for

connecting panels together. The product has a knock-down construction.It consist of 18mm Thick Pre-laminated

twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm

1 BOARD ROOM thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a Each 1 4,27,288.25 4,27,288.25

knock-down construction.An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder

coated(DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate

is provided below worktop. Cutout on top with two piece injectionmoulded plastic part polymer component is

fitted to pull out audio,video cables ontoworktop and connect devices charger to power socket below worktop.

Digitally signed by

PRADYUMNA MUKHERJEE

HIGH BACK CHAIR FOR CABIN

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT HIGH BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for 25%

compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam

with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 76.7 cm. (D) ARMRESTS: The

armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast

Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-Down adjustment has 8

position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width

adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm

range).Armrest top is made up of high density PU molded over glass filled Poly-amide inner.POSTURE PERFECT

MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type.

2 Main chair Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3- Each 1 80,682.50 80,682.50

position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated

with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish

die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position.

It can be adjusted in the range of 7.5+0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height adjustment has an adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-

cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-

center dia. TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU

lining, having 6.50.1cm wheel Diameter and assembled to pedestal.

VISITOR CHAIR FOR CABIN

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT FULL BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for 25%

compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam

with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 61.8 cm. (D) ARMRESTS: The

armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast

Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-Down adjustment has 8

position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width

adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm

range).Armrest top is made up of high density PU molded over glass filled Poly-amide inner.POSTURE PERFECT

MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type.

3 Chair Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3- Each 48 75,129.00 36,06,192.00

position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated

with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish

die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position.

It can be adjusted in the range of 7.5+0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height adjustment has an adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-

cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-

center dia. TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU

lining, having 6.50.1cm wheel Diameter and assembled to pedestal.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and Placing in position Conference table for 25 seater having 12 Nos of 2 Seater Modules of size

1350mm X 600mm X 740mm . Worktop- Made of 25mm thick MDF-one side pre-laminate board conforming to

IS-14587:1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge.Plastic ABS access flap

is provided for easy access to wires and cables.Modesty consist of 18mm Thick Pre-laminated twin board of E1-

P2 grade and approved shadeconforming to IS-12823:1990, Aluminium alloy 63400 - WP profile is used for

connecting panels together. The product has a knock-down construction.It consist of 18mm Thick Pre-laminated

twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm

4 thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a Each 1 5,31,998.05 5,31,998.05

knock-down construction.An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder

coated(DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate

is provided below worktop. Cutout on top with two piece injectionmoulded plastic part polymer component is

fitted to pull out audio,video cables ontoworktop and connect devices charger to power socket below worktop.

Providing and Placing in Position High Back Chair. The cushioned seats shall be made of injection moulded plastic

outer and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane

foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall

be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS

ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm

W x 77 cm D. The armrest top shall be moulded from polurethane, and shall be upholstered with pure leather

and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm

thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5

steps. The adjustable tilting mechanism shall be designed with the following features : 360° revolving type, front-

pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort, Tilt tension

adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt angle to the

chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black powder coated.

Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat depth adjustment range

shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism housed in plastic T spine. It can

be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic

height adjustment shall have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast

polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre

dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and

assembled to pedestal.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5-114cm.

Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic outer and

inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof

Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6

cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW

round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. The armrest top shall be

moulded from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable

type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome

plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism

shall be designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground

and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating

position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be

integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back

frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the range of

7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall

have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and

fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel

castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

Providing and placing in position meeting table. Size 4500mmx1500mmx 740mm. Worktop shall be made from

25mm thick MDF one side prelaminate board with 0.4mm PVC membrane pressed on to top and having

chamfered edge. Soft closing dual access flap provided for access to power supply and data cables. The Under-

structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade

conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy

Meeting room 1 63400 - WP profile is added at bottom edges for improving the aesthetics.The product has a knock-down

5th Floor construction. A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60

microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for standard 8 module Anchor

Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual

Cables(eg. HDMI,VGA-A,etc). The product must be UL Greenguard certified.Complete all as per the direction of

Engineer in Charge.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5-114cm.

Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic outer and

inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof

Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6

cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW

round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. The armrest top shall be

moulded from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable

type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome

plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism

shall be designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground

and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating

8 Meeting chairs Each 12 45,074.80 5,40,897.60

position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be

integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back

frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the range of

7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall

have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and

fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel

castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

Providing and placing in position meeting table. Size 3600mmx 1500mmx 740mm. Worktop shall be made from

25mm thick MDF one side prelaminate board with 0.4mm PVC membrane pressed on to top and having

chamfered edge. Soft closing dual access flap provided for access to power supply and data cables. The Under-

structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade

conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy

Meeting room 2 63400 - WP profile is added at bottom edges for improving the aesthetics.The product has a knock-down

5th Floor construction. A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60

microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for standard 8 module Anchor

Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual

Cables(eg. HDMI,VGA-A,etc). The product must be UL Greenguard certified.Complete all as per the direction of

Engineer in Charge.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5-114cm.

Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic outer and

inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof

Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6

cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW

round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. The armrest top shall be

moulded from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable

type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome

plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism

shall be designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground

and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating

10 Meeting chairs Each 10 40,074.80 4,00,748.00

position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be

integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back

frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the range of

7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall

have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and

fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel

castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

Providing and placing in position meeting table. Size 4500mmx1500mmx 740mm. Worktop shall be made from

25mm thick MDF one side prelaminate board with 0.4mm PVC membrane pressed on to top and having

chamfered edge. Soft closing dual access flap provided for access to power supply and data cables. The Under-

structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade

conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy

Meeting room 1 63400 - WP profile is added at bottom edges for improving the aesthetics.The product has a knock-down

4th Floor construction. A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60

microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for standard 8 module Anchor

Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual

Cables(eg. HDMI,VGA-A,etc). The product must be UL Greenguard certified.Complete all as per the direction of

Engineer in Charge.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5-114cm.

Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic outer and

inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof

Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6

cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW

round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. The armrest top shall be

moulded from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable

type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome

plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism

shall be designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground

and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating

12 Meeting chairs Each 12 40,074.80 4,80,897.60

position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be

integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back

frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the range of

7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall

have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and

fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel

castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

Providing and placing in position meeting table. Size 2350mmx 1150mmx 740mm. Worktop shall be made from

25mm thick MDF one side prelaminate board with 0.4mm PVC membrane pressed on to top and having

chamfered edge. Soft closing dual access flap provided for access to power supply and data cables. The Under-

structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade

conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy

Meeting room 2 63400 - WP profile is added at bottom edges for improving the aesthetics.The product has a knock-down

4th Floor construction. A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60

microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for standard 8 module Anchor

Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual

Cables(eg. HDMI,VGA-A,etc). The product must be UL Greenguard certified.Complete all as per the direction of

Engineer in Charge.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5-114cm.

Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic outer and

inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof

Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6

cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW

round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. The armrest top shall be

moulded from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable

type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome

plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism

shall be designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground

and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating

14 Meeting chairs Each 6 34,530.45 2,07,182.70

position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be

integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back

frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the range of

7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall

have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and

fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel

castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

Providing and Placing in position Conference table for 20 seater having 10 Nos of 2 Seater Modules of size

1350mm X 600mm X 740mm . Worktop- Made of 25mm thick MDF-one side pre-laminate board conforming to

IS-14587:1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge.Plastic ABS access flap

is provided for easy access to wires and cables.Modesty consist of 18mm Thick Pre-laminated twin board of E1-

P2 grade and approved shadeconforming to IS-12823:1990, Aluminium alloy 63400 - WP profile is used for

connecting panels together. The product has a knock-down construction.It consist of 18mm Thick Pre-laminated

twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm

15 thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a Each 1 3,28,683.80 3,28,683.80

knock-down construction.An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder

coated(DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate

is provided below worktop. Cutout on top with two piece injectionmoulded plastic part polymer component is

fitted to pull out audio,video cables ontoworktop and connect devices charger to power socket below worktop.

Digitally signed by

PRADYUMNA MUKHERJEE

HIGH BACK CHAIR FOR CABIN

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT HIGH BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for 25%

compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam

with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 76.7 cm. (D) ARMRESTS: The

armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast

Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-Down adjustment has 8

position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width

adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm

range).Armrest top is made up of high density PU molded over glass filled Poly-amide inner.POSTURE PERFECT

MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type.

16 Main chair Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3- Each 1 48,750.80 48,750.80

position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated

with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish

die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position.

It can be adjusted in the range of 7.5+0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height adjustment has an adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-

cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-

center dia. TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU

lining, having 6.50.1cm wheel Diameter and assembled to pedestal.

VISITOR CHAIR FOR CABIN

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT FULL BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for 25%

compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam

with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 61.8 cm. (D) ARMRESTS: The

armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast

Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-Down adjustment has 8

position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width

adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm

range).Armrest top is made up of high density PU molded over glass filled Poly-amide inner.POSTURE PERFECT

MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type.

17 Chair Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3- Each 44 34,530.45 15,19,339.80

position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated

with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish

die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position.

It can be adjusted in the range of 7.5+0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height adjustment has an adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-

cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-

center dia. TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU

lining, having 6.50.1cm wheel Diameter and assembled to pedestal.

Digitally signed by

PRADYUMNA MUKHERJEE

5 TH FLOOR - -

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery -Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid

wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

1 3 seater sofa initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , each 2 89,389.50 1,78,779.00

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Providing and placing sofa of size 1420mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery -Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid

wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

2 2 seater sofa initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , each 3 65,239.50 1,95,718.50

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

SIDE TABLE compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown each 2 16,675.00 33,350.00

construction built for longevity.

Overall size of 1000mm(L)1000mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

CENTRE TABLE compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown each 2 29,591.80 59,183.60

construction built for longevity.

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery -Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid

wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

3 3 seater sofa initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , each 1 89,389.50 89,389.50

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Providing and placing sofa of size 1020mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame

with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to

enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch

, Zigzag Spring - 3.8mm

Comfort- The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with

sinking feeling.

Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

SIDE TABLE compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown each 1 16,675.00 16,675.00

construction built for longevity.

Digitally signed by

PRADYUMNA MUKHERJEE

Overall size of 1000mm(L)1000mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

CENTRE TABLE compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown each 1 29,591.80 29,591.80

construction built for longevity.

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery -Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid

wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

5 3 seater sofa initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , each 1 89,389.50 89,389.50

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Providing and placing sofa of size 1020mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame

with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to

enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch

, Zigzag Spring - 3.8mm

Comfort- The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with

sinking feeling.

Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

ADDITIONAL SIDE TABLE compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown each 4 16,675.00 66,700.00

construction built for longevity.

Overall size of 1000mm(L)1000mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

ADDITIONAL CENTRE TABLE compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown each 2 29,591.80 59,183.60

construction built for longevity.

6TH FLOOR LOUNGE - -

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery -Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid

wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

7 3 seater sofa initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , each 2 89,389.50 1,78,779.00

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Providing and placing sofa of size 1420mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery -Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid

wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

8 2 seater sofa initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , each 4 65,239.50 2,60,958.00

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Digitally signed by

PRADYUMNA MUKHERJEE

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

SIDE TABLE compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown each 4 16,675.00 66,700.00

construction built for longevity.

Overall size of dia 600x450mm(H)Designed for the modern minimalist with a need for handy,

compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown each 2 16,675.00 33,350.00

construction built for longevity.

Overall size of 1000mm(L)1000mm(D)x450mm(H)Designed for the modern minimalist with a need for handy,

CENTRE TABLE compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown each 2 29,591.80 59,183.60

construction built for longevity.

Providing and Placing Reception TAble of Size as Per Site WORKTOP - Main worktop Made of 43mm Thick (±1)

combination of MDF and particle board with top veneer face coated with clear lacquer. All edges are edge

banded with matching 1mm thick veneer lipping.LEATHER PAD:Made of 18mm Thick (±1) MDF with Leatherette

wrapped around top surface. This leather pad is fixed to main top panel.DRAWER UNIT:Top panel and drawer

unit modesty panel is made of 43mm Thick (±1) combination ofMDF and particle board with top veneer face

coated with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining construction is

of 18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge

banded with matching 2 mm thick PVC lipping. Bottom panel of drawer is 9mm thick particle board with

leatherette on top surface.Drawer unit is provided with soft closing channels for smooth opening and

closing.Drawer unit is secured with side central lock.OPEN STORAGE UNIT:Top panel and open storage unit

modesty panel is made of 43mm Thick (±1) combination of MDF and particle board with top veneer face coated

1 Reception Desk with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining construction is of Each 3 1,38,000.00 4,14,000.00

18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge

banded with matching 2 mm thick PVC lipping.MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of

E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC

lipping. Modesty is fitted with aluminum trims.UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin

board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm

thick PVC lipping. Door is fixed with soft closing hinges and handle is provided for ease of opening.Also lock is

provided on side panel for security.ACCESS FLAP WITH POWER BOX:Soft closing access flap with power box

contains 3 Universal Sockets, 2 USB power points, 1 HDMI connection, 1 inbuilt misc. cable grommet and CAT 3

and CAT 6connections.

Digitally signed by

PRADYUMNA MUKHERJEE

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made

up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester

mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-

51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is

having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in

aluminium structure of armrest which is connected to aluminium back spine and is operated with button.

Armtop is made up of PU molded over plastic inner. The mechanism shall be Active BioSynchro Mechanism. The

mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-

Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with

feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing

should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic

2 Reception Chair height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished Each 3 20,048.80 60,146.40

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. The neckrest assembly consists of upholstered neckrest inner(material-

poly propylene) with moulded polyurethane foam and polyster fabric. upholstered inner shall be fixed to neck

rest cover. neckrest shall be fixed to back assembly through neckrest spline. Overall dimensions of Chair shall be,

Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min

109.3 to max 124.4 cm. Seat height - min 45.5cm to max 55.5cm. Dimensions tolerance / variations shall be

within +/- 1 cm.

Overall size of dia 600x450mm(H)Designed for the modern minimalist with a need for handy,

compartmentalized storage.• Tabletop of durable,vineeered with pu finish , modern look.• A strong, knockdown Each 1 16,675.00 16,675.00

construction built for longevity.

Overall size of 1000mm(L)1000mm(D)x450mm(H)Designed for the modern

minimalist with a need for handy, compartmentalized storage.• Tabletop of durable, toughened glass with a

3 Center table Each 3 15,114.45 45,343.35

digitally back-printed Skyline pattern creates a sleek, modern look.• A strong, knockdown construction built for

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame

with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to

enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch

, Zigzag Spring - 3.8mm

Comfort- The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with

sinking feeling.

Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and placing sofa of size 1520mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aestheticsS Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood

frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood

initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , Each 1 75,693.00 75,693.00

webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3 which

enhances comfort and cushioning with sinking feeling.Ground Elevation- Equipped with legs, the sofa is elevated

to allow a level of ground clearance.

Providing and placing sofa of size 1020mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame

with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to

enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch

, Zigzag Spring - 3.8mm

Comfort- The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with

sinking feeling.

Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.

Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern

minimalist with a need for handy, compartmentalized storage.• Tabletop of durable, toughened glass with a

6 Corner table Each 6 11,311.40 67,868.40

digitally back-printed Skyline pattern creates a sleek, modern look.• A strong, knockdown construction built for

P STORAGE - -

Storwel plain shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It

should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield

strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA

‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking

1 mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Each 24 26,819.15 6,43,659.60

Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic

base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour

options and shelving options shall be available.

Storwel plain shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It

should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield

strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA

Storage room ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking

2 wall side mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Each 18 26,819.15 4,82,744.70

storage Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic

base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour

options and shelving options shall be available.

Digitally signed by

PRADYUMNA MUKHERJEE

Supplying of side storage unit of officers having dimension 1190WX 450DX 1200 H:Overall size of hinge door unit

is 1190(H)x740mm (h)x450 mm (D). Providing and placement of back storages with : CONSTRUCTION &

MATERIAL Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with

metal cladding of 1.0 mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy

polyester powder of 50±10 microns thickness. TOP OPTIONS- The Storage units are provided with 11mm thk

bent metal tops made of 1.0 mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester

powder of 50± 10 microns thickness. DOOR & DOOR OPENINGtwo door opening for all other width of 1150

W.The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing

laminate on the other side. SHELVING- Height wise adjustable shelf mounting holes provided on side panels for

easy interchange of shelf height as required. Fixed shelves along with adjustable shelves provided only in case of

Workstation 4.0 feet height units. No fixed shelves for 2.5 feet height storage units. Uniformly distributed load capacity for

3 area storage each shelf is 40kg maximum. SKIRTING OPTION- The skirting units are provided with 150mm high skirting made Each 78 21,836.20 17,03,223.60

(1200X450) of 1.0 mm thick C.R.C.A(as per IS:513) and is coated with Epoxy polyester powder of 50+-10 micros thickness.

LEVELER-Screw type adjustable leverer with plastic base provides vertical adjustment for floor unevenness and

levelling of units.BACK PANELS Back panels are made of 18mm thick pre-laminated boards with options of

decorative as well as fabric finishes. 2.5 height units consists of single back panel whereas 4.0 height and 4.5

height units consist of split back top panel and split back bottom panels separated by an Aluminium extrusion.

LOCKING MECHANISM- 3-way nickel plated wooden furniture lock is provided for effective and positive locking

of doors. HANDLE- Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy

opening and closing.The OEM should be ISO 9001:2015,ISO 14001:2015 & ISO 18001:2007 certified.

Supplying of side storage unit of officers having dimension 1050WX 450DX 1150H:Overall size of hinge door unit

is 1190(H)x740mm (h)x450 mm (D). Providing and placement of back storages with : CONSTRUCTION &

MATERIAL Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with

metal cladding of 1.0 mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy

polyester powder of 50±10 microns thickness. TOP OPTIONS- The Storage units are provided with 11mm thk

bent metal tops made of 1.0 mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester

powder of 50± 10 microns thickness. DOOR & DOOR OPENINGtwo door opening for all other width of 1050

W.The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing

laminate on the other side. SHELVING- Height wise adjustable shelf mounting holes provided on side panels for

easy interchange of shelf height as required. Fixed shelves along with adjustable shelves provided only in case of

Workstation 4.0 feet height units. No fixed shelves for 2.5 feet height storage units. Uniformly distributed load capacity for

4 area storage each shelf is 40kg maximum. SKIRTING OPTION- The skirting units are provided with 150mm high skirting made Each 54 17,670.90 9,54,228.60

(1050X450) of 1.0 mm thick C.R.C.A(as per IS:513) and is coated with Epoxy polyester powder of 50+-10 micros thickness.

LEVELER-Screw type adjustable leverer with plastic base provides vertical adjustment for floor unevenness and

levelling of units.BACK PANELS Back panels are made of 18mm thick pre-laminated boards with options of

decorative as well as fabric finishes. 2.5 height units consists of single back panel whereas 4.0 height and 4.5

height units consist of split back top panel and split back bottom panels separated by an Aluminium extrusion.

LOCKING MECHANISM- 3-way nickel plated wooden furniture lock is provided for effective and positive locking

of doors. HANDLE- Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy

opening and closing.The OEM should be ISO 9001:2015,ISO 14001:2015 & ISO 18001:2007 certified.

Digitally signed by

PRADYUMNA MUKHERJEE

Supplying of side storage unit of officers having dimension 900WX 450DX 1150H:Overall size of hinge door unit is

1190(H)x740mm (h)x450 mm (D). Providing and placement of back storages with : CONSTRUCTION & MATERIAL

Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal

cladding of 1.0 mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyester

powder of 50±10 microns thickness. TOP OPTIONS- The Storage units are provided with 11mm thk bent metal

tops made of 1.0 mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±

10 microns thickness. DOOR & DOOR OPENINGtwo door opening for all other width of 900 W.The doors are

made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the

other side. SHELVING- Height wise adjustable shelf mounting holes provided on side panels for easy interchange

of shelf height as required. Fixed shelves along with adjustable shelves provided only in case of 4.0 feet height

units. No fixed shelves for 2.5 feet height storage units. Uniformly distributed load capacity for each shelf is 40kg

5 Workstation areamaximum. SKIRTING OPTION- The skirting units are provided with 150mm high skirting made of 1.0 mm thick

C.R.C.A(as per IS:513) and is coated with Epoxy polyester powder of 50+-10 micros thickness. LEVELER-Screw

type adjustable leverer with plastic base provides vertical adjustment for floor unevenness and levelling of

units.BACK PANELS Back panels are made of 18mm thick pre-laminated boards with options of decorative as well

as fabric finishes. 2.5 height units consists of single back panel whereas 4.0 height and 4.5 height units consist of

split back top panel and split back bottom panels separated by an Aluminium extrusion. LOCKING MECHANISM-

3-way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE-

Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing.The

OEM should be ISO 9001:2015,ISO 14001:2015 & ISO 18001:2007 certified.

Supplying of side storage unit of officers having dimension 750WX 450DX 1150H:Overall size of hinge door unit is

1190(H)x740mm (h)x450 mm (D). Providing and placement of back storages with : CONSTRUCTION & MATERIAL

Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal

cladding of 1.0 mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyester

powder of 50±10 microns thickness. TOP OPTIONS- The Storage units are provided with 11mm thk bent metal

tops made of 1.0 mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±

10 microns thickness. DOOR & DOOR OPENINGtwo door opening for all other width of 750 W.The doors are

made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the

other side. SHELVING- Height wise adjustable shelf mounting holes provided on side panels for easy interchange

of shelf height as required. Fixed shelves along with adjustable shelves provided only in case of 4.0 feet height

units. No fixed shelves for 2.5 feet height storage units. Uniformly distributed load capacity for each shelf is 40kg

6 Workstation areamaximum. SKIRTING OPTION- The skirting units are provided with 150mm high skirting made of 1.0 mm thick

C.R.C.A(as per IS:513) and is coated with Epoxy polyester powder of 50+-10 micros thickness. LEVELER-Screw

type adjustable leverer with plastic base provides vertical adjustment for floor unevenness and levelling of

units.BACK PANELS Back panels are made of 18mm thick pre-laminated boards with options of decorative as well

as fabric finishes. 2.5 height units consists of single back panel whereas 4.0 height and 4.5 height units consist of

split back top panel and split back bottom panels separated by an Aluminium extrusion. LOCKING MECHANISM-

3-way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE-

Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing.The

OEM should be ISO 9001:2015,ISO 14001:2015 & ISO 18001:2007 certified.

Digitally signed by

PRADYUMNA MUKHERJEE

Supplying of side storage unit of officers having dimension 450WX 450DX 740H:Overall size of hinge door unit is

1190(H)x740mm (h)x450 mm (D). Providing and placement of back storages with : CONSTRUCTION & MATERIAL

Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal

cladding of 1.0 mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyester

powder of 50±10 microns thickness. TOP OPTIONS- The Storage units are provided with 11mm thk bent metal

tops made of 1.0 mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±

10 microns thickness. DOOR & DOOR OPENINGtwo door opening for all other width of 450 W.The doors are

made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the

other side. SHELVING- Height wise adjustable shelf mounting holes provided on side panels for easy interchange

of shelf height as required. Fixed shelves along with adjustable shelves provided only in case of 4.0 feet height

Workstation units. No fixed shelves for 2.5 feet height storage units. Uniformly distributed load capacity for each shelf is 40kg

7 area storage maximum. SKIRTING OPTION- The skirting units are provided with 150mm high skirting made of 1.0 mm thick Each 18 11,356.25 2,04,412.50

(450X450) C.R.C.A(as per IS:513) and is coated with Epoxy polyester powder of 50+-10 micros thickness. LEVELER-Screw

type adjustable leverer with plastic base provides vertical adjustment for floor unevenness and levelling of

units.BACK PANELS Back panels are made of 18mm thick pre-laminated boards with options of decorative as well

as fabric finishes. 2.5 height units consists of single back panel whereas 4.0 height and 4.5 height units consist of

split back top panel and split back bottom panels separated by an Aluminium extrusion. LOCKING MECHANISM-

3-way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE-

Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing.The

OEM should be ISO 9001:2015,ISO 14001:2015 & ISO 18001:2007 certified.

Q COMPACTOR ROOM - -

Compactor-Overall size2047H x 1200W x 800D(As per layout). Designed for long life and easy part replacement.

Uses one common aisle spacethat optimizes available space. PU drive wheel for firm grip and hassle-free

Compactor mobility. Channel stoppers prevent derailment. Label holders with neat transparent acrylic sheets facilitate easy

1 room 1 4th identification. Locking stiffeners for centralised locking ensures safety of documents. Rotating locks with easy to Each 1 2,77,385.75 2,77,385.75

floor identify lock/unlock positions ensures safety. Shims provided below the rails for right laveling.Complete all as per

the direction of Engineer-in-charge.

Compactor-Overall size2047H x 1200W x 800D(As per layout). Designed for long life and easy part replacement.