REPAIR AND MAINT OF BUILDING AND INTERNAL WIRING AND SPLIT / WINDOW TYPE AC , WATER COOLER , DESERT COOLAR DEEP FREZES AND EFRIGERATORS , CEILING FAN /EXHAUST FAN AND RO PLANT AND OTHER CONNECTED MISC WORK AT RAMGARH UNDER GE (AF) JAISALMER

Amount

Galvanized steel water tubing medium grade of 15mm bore with & including all fittings fixed to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing , complete all as specified and directed.

Galvanized steel water tubing medium grade of 20mm bore with & including all fittings fixed to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing , complete all as specified and directed.

Re fixing 15 mm bore old steel tubing and connections, in new or old position with new fitting (walls, ceiling, floors etc) including taking up or down existing steel water tubing and connections complete including cleaning for re fixing complete all as specified and as directed.

Re fixing 20 mm bore old steel tubing and connections, in new or old position with new fitting (walls, ceiling, floors etc) including taking up or down existing steel water tubing and connections complete including cleaning for re fixing complete all as specified and as directed.

Vitreous china wash hand basin white colour flat back of size 580x450mm including cutting for and pinning in ends of or erecting stand including waste fitting, brass chromium plated 32mm size with longh with including a pair of cast iron brackets embedded in PCC 1:3:6 type C-1 blocks of size 10x7.5x15cm with including dismantling and taking down old unserviceable complete all as specified and directed.

Sink with drainage board made of stainless steel 1mm thick for Kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall including fixing cantilever brackets and connecting union to pipe over all size 915mm x 460mm, bowl size 410mm x 330mmx 160mm with all fitting and fixure fixed as in repair complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 500 Litre capacity triple layered (white cylindrical vertical with closed top) ISI marked, hoisted & fixed in position with 20mm bore ball valve of high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water storage tank complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 1000 Litre capacity triple layered (white cylindrical vertical with closed top) ISI marked, hoisted & fixed in position with 20mm bore ball valve of high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water storage tank complete all as specified and directed.

Cleaning and removing all scale and dirt etc from tanks and mouth and circulating pipes etc, exc 250 ltr & n.exc 500 ltrs capacity and marking date of cleaning with paint complete all as specified and directed.

Cleaning and removing all scale and dirt etc from tanks and mouth and circulating pipes etc, exc 500 ltr & n.exc 1000ltrs capacity and marking date of cleaning with paint complete all as specified and directed.

PVC Cover of O.H water tanks 500 litrs /1000 ltrs Capacity including locking arrangements and removing old broken cover complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames), area not exceeding 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames exc 1.5 sq. m but n exc 4 sq. m each complete all as specified and directed.

Taking down shutters any description area exceeding 1.00 sqm each but not exceeding 2.00 sqm each complete all as specified and directed.

30mm thick flush shutters factory made solid core construction with block boards core and plywood face panels, commercial type on both sides (ISI marked) fixed to chowkhats complete all as specified and directed.

Wood grain printed 1mm PVC sheet fixed or laid on to flush doors by using rubber based adhesive, complete all as specified and directed.

PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube 19mmx19mmx19 gauge and PDM rubber gasket weather seal to be provided through out the frame. The profile shall be mitre cut at two corners and jointed by inserting 02 Nos of 150mm long brackets of 15mmx15mmx15 gauge MS square tube inside the 19mmx15mm MS square tube and suitable screwed complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (style), consisting of frame made out of MS tubes for stiles and for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed.

Factory made Second class hard wood 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares with plain chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or founded, fitted with cut and mitred beads for securing glass or wire cloth any number, etc sizes of members of shutter as specified in SSR Part-I complete all as specified and directed.

PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in hold fast, ,filling of pressed steel frame ,coping incl weathering slightly rounded or chamfered angle and throating including necessary use and waste of formwork and finishing the top surface of concrete even and smooth with using extra cement complete all as specified and as directed

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete of Gde E-165 (Fe-290), drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooken and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing in position complete all as specified and directed. Note : Cost of welding butt hinges to the door frame deemed to included in quoted rate .

MS hold fast made out of flat iron using steel conforming to Fe-290 Gde-E-165 complete all as specified and as directed

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples including wooden beads etc fixed as in repair complete all as specified and directed.

3mm thick sheet glass ordinary quality and glazing with oil putty not exceeding 0.50 sqm in each pane and fixing new panes any building height (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick sorrounds, glazed with putty or fixed with beads and fixing new ones, including hacking out old broken glass complete all as specified and directed.

4mm thick figured glass pin head type and glazing with oil putty not exceeding 0.50 sqm in each pane and fixing new panes any building height (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick sorrounds, glazed with putty or fixed with beads and fixing new ones, including hacking out old broken glass complete all as specified and directed.

Glazed ceramic coloured tiles as in dado/skirting 300x 200x 6-7mm thick on vertical surfaces, over and including 15mm thick cement and sand mortar (1:4) backing coat set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tile including dismantling floor, hearth or wall tiling with cement mortar bedding complete all as specified and directed.

Non Skid colouredceramic tiles 7 to 8mm thick (square /rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc over 15mm thick in cement and mortar (1:6) bedding set and jointed in neat cement slurry and pointed in coloured cement to match and including dismantling of existing tiling with cement mortar bedding complete all as specified and directed

Non Skid coloured ceramic tiles 7 to 8mm thick (square /rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc over 15mm thick in cement and mortar (1:6) bedding set and jointed in neat cement slurry and pointed in coloured cement to match and including dismantling of existing tiling with cement mortar bedding complete all as specified and directed

18-20mm thick black granite slabs/Tiles laid in floors/treads over 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white cement with admixture of pigment to match the shade of granite including dismantling of existing tiling with cement mortar bedding complete all as specified and directed

Ditto all as per srl item No 27.00 here in above but in skirtings/risers with 10 mm thick backing coat in CM (1:4).

PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base including finishing the top surface of concrete even and rough in any thickness including demolition of existing cement concrete complete all as specified and directed.

Factory made chequered cement concrete tiles, 300cm x 300cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment, over and including 20mm thick screed bed in cement and sand mortar 1:6 and including dismantling floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed.

Plain cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as in kerbs stone and the likes including weathering, slightly rounded or chamfered angles and throating including jointed ,pointed in cement mortar 1:4 embeding in the ground complete all as specified and directed.

Anodised aluminium snap grid frame work for false ceiling as per manufacturer's instructions with hangers from RCC soffit/steel trusses with 6mm dia GI rod (upto 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long with including exposed metal frame ceiling with 12mm thick perforated paticle board/ tiles with lamination on inner side for insula-tion, 600mmx 600mm in size, fixed with screw to aluminium work or with staples on snap grid in ceiling, flat or sloping and including dismantling and taking down old unserviceable complete all as specified and directed.

10mm thick plaster in cement mortar (1:4) on external wall surface finished even & fair without using extra cement including taking down old plaster complete all as specified and directed.

5mm thick ceiling plaster in cement mortar (1:3) on uneven faces of concrete surfaces of ceiling soffits of chajjas/ drop & roof projectiom facia etc , including taking down old plaster complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of cement primer in different tints as approved complete all as specified and directed.

Preparation of newly plastered or unplastered surfaces of ceiling surfaces and applying three coats of white wash on ceiling, soffit of chajjas /drop and roof projection facia complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of chalk whitening complete all as specified and directed.

Preparation of newly plastered surfaces of ceiling and applying two coats of distemper oil emulsion over a coat of chalk whitening complete all as specified and directed.

Preparation of old decorated plastered surfaces of walls by washing, rubbing down and stopping of distempered painted sufaces and applying two coats of oil emulsion distemper of any tint etc complete all as specified and directed.

Preparation of old treated/decorated external wall surfaces of any storeys/height upto 10m and applying two coat of cement based paint in different tints in sigma/camouflage pattern as approved complete all as specified and directed.

Preparation of old treated/ decorated external wall/roof surfaces of any storeys/height upto 10m of any description and applying two coat of exterior emulsion paint (weather coat) 1st quality in different tints/shades in sigma/ camouflaging pattern as approved complete all as specified and directed.

Preparation of old painted wooden surfaces of any description exceeding 10cm width or girth and applying one coat of synthetic enamel paint of any tint etc complete all as specified and directed.

Preparation of old painted steel surfaces over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Easing and adjusting of steel window/ventilators including removing rusted and forging materials and replacing broken hinges including welding and all labour complete all as specified and directed.

Easing and adjusting of aluminium door including necessary joining cleats, glazing clips, rubber packing and anodised aluminium snap beading, screws, anodised aluminium fittings fixing aluminium bedding, rubber beding removing rusted and forging materials and replacing broken hinges including fixing necessary aluminium flat and aluminium angle complete all as specified and directed.

Easing and door shutters for easy closing / opening tightening of hinges or changing the position of hinges adjustment of tower bolts, sliding bolts with new screws complete all as specified and directed.

Precast reinforced cement concrete 1:2:4 type B-1,using 20 mm graded aggregate as in manhole covers base slab ,baffle wall and similar articles with plain faces including necessary moulds and setting in cement and sand mortar 1:4 etc including necessary use and waste of form work complete all as specified and as directed . Note :- Reinforcement shall be measured and paid for separately under appropriate items of this schedule).

Mild steel TMT bars as in reinforcement, 6mm to 8 mm dia , cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed

Removal of blockage in between WC and nahani trap/WC to Ist manhole / floor trap to nahani trap etc. by flexible roding and removal the all dirt up to a distance of 100 metre complete all as specified and directed. Note : (i) In case a blockage reoccured with in 7 days the same shall be removed without any extra cost of the Govt. (ii) Cleaning of line in between manhole where in the blockage remove shall deemed to incl the rate coated. (iii) If contractor failed to clear the blockage with in 24 hours from the receipt of complaint, a penalty of Rs. 50 per day will charge up to 7 days and after 7 days same will be Rs. 100.00 till completion of complaint.

Cleaning of septic tank /soak well of 25 users capacity by balling out taking out sludge and removing the sludge to a distance exceeding 1.5 Km but not exceeding 2.00 Km from the camp area and including removing stone patti/RCC cover slab and refixing, complete all as directed.

cleaning of septic tank /soak well of 10 users capacity by balling out taking out sludge and removing the sludge to a distance exceeding 1.5 Km but not exceeding 2.00 Km from the camp area and including removing stone patti/RCC cover slab and refixing, complete all as directed.

Cleaning and desilting of manhole of any size and capacity or description but depth not exceeding 2.0 metre by excavation sewage wet/dry soil in foul condition and removing the waste in covered vehicles outside the MD land by taking all necessary precautions and including pumping out fluid, cleaning of sludge from manholes, placing the cover of manholes in position and removing the sludge in covered van/ trolley out side in MD land complete all as specified and directed.

Cleaning of sewage line of 100/150/200 mm bore by roding and flush water in line after roding to clean the line complete all as directed by Engineer-in-Charge. Note:- The contractor shall arrange safaiwala immediately as receipt of complaint and ensure that complaint is resolved within 24 hours and no lapses will be allowed. Note: (i) In case a blockage reoccured with in 07 days ,the same shall be removed without any extra cost to the Govt.(ii) cleaning of line in between manholes where in the blockage remove shall deemed to incl the rate coated.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required (bore of pipe 150 mm) etc complete all as specified.

Excavation in trenches n.exc 1.5 m wide or n exc 10 sqm in plan area and n.exc 1.5 m in depth and getting out in any type of soil complete all as specified and as directed .

PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundaton for manhole etc complete all as specified.

PCC 1:4:8 type D-2 using 40mm graded stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150mm bore drain pipe complete all as specified and as directed.

Plain cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate ) in surface channels, drains and benching for man holes finished even and smooth etc complete all as specified.

PCC 1:3:6 type C1, using 20mm graded aggregates as in copings including weathering, slightly rounded or chamfered angles and throating and necessary form work and finishing the top surface of concrete even and smooth without using extra cement complete all as specified.

Precast cement concrete (1:3:6), type C-1 (using 20mm graded stone aggregate) as solid block masonary exceeding 10cm and set in cement and sand mortar (1:4) including demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed.

15mm thick plaster in cement mortar (1:4) on external wall surface finished even & fair without using extra cement including taking down old plaster complete all as specified and directed.

150mm bore reinforced concrete pipe, class NP2, laid and jointed with collars, laid and jointed on concrete bed complete including testing, after demolition and breaking up existing drain pipes set in cement mortar including bedding haunching complete all as specified & as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified.

Removal of excavated soil/ material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.50 metre above the starting point complete all as specified.

100mm thick cement concerete 1:2:4 type B-1 using 20mm graded aggragete in alternate bays all as specified and directed.

30mm thick Wearproof granolithic metallic hardner concrete as per in manufacturer instructions (included metallic hardner) complete all as specified and directed. Note :- The cost of metallic hardner is inclusive in the unit rate quoted by the contractor.

75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection , finished the surface even and smooth without using extra cement complete

Dismantling of existing water proofing roof treatment any type, and in any location up to existing RCC Slab by Chiesling, drilling, scraping and any description and in any position and thrown away complete all as directed.

20mm thick cement screed in cement mortar 1:4, including finishing even and smooth with out using extra cement mixed with water proofing compound @3% by weight of cement over cleaned roof surface, as in grading to RCC roof surface,complete all as specified. Note - Water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified and directed

Aplying evenly one coat of binding material using blown type bitumen confirming to IS-702 Grade 85/[email protected] kg/Sqm over one coat of cold bituminous oil based primer (IS:3384)(as approved by Engineer -in -charge)@ 250 gm/sqm over plaster surfaces including cleaning surfaces of complete all as specified.

APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (weight not less than 150gms/sqm) land on primed surface by LPG torched application over applying evenly one coat of binding material using blown type bitumen confirming to IS-702 grade 85/25 at the rate 1.20 Kg/Sqm over one coat of cold bitumenous oil based primer (IS : 3384) at the rate 250gm/sqm including cleaning surfaces complete all as specified and directed.

PCC (1:2:4) type B-0 using 12.5mm graded stone agg as in Roof padding,or similar work complete all as specified & directed

100 mm long stainless steel Butt hinges etc complete all as specified..

150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

150mm long extruded aluminium alloy handles, cast type anodised (ISI marked) complete all as specified and directed.

300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed as in repair complete all as specified and directed.

20mm dia ball valves, high pressure of PTMT (minimum weight 210 gms) (Polytetra methylene terephthalate) with epoxy coated aluminum rod & high density plastic ball and fly nut, screwed fixed as in repair complete all as specified and as directed.

10 Litres capacity PVC valve less syphonic action type, flushing cistern low level, white coloured, with inlet, ball valve, float and handle including brackets complete with flush pipe and fixed as in repair complete all as specified and directed.

White coloured vitreous china urinal half stall type with 40mm size chromium plated waste coupling with long screwed shanks and fly nuts flange end bedded in red lead and fixed as in repair complete all as specified and directed.

Vitreous china wash down water closet pan (Pedestal pattern) of size 580x440mm , white coloured, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic water closet seat cover (white coloured) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device fixed as in repair complete all as specified and directed.

Vitreous china squatting pan 'Orissa Pattern' of size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with P' or 'S' trap complete including jointing and making good to floor as per existing and including dismantling and taking down old unserviceable complete all as specified and directed.

40mm dia low density polyethylene pipes (LDPE) of pressure rating 6 Lg/CM2 fixed complete to walls, ceiling or in floors etc fixed as in repair complete all as specified and directed.

32/40mm bore PVC flexible down take waste pipe fixed to WHB, urinal or sink fixed as in repair complete all as specified and directed.

Harrison rails, mild steel, chromium platedwith fixing brackets, stops, rollers etc. fixed as in repair complete all as specified and directed.

6 mm thick Plywood grade BWR, type BB for covering of window cfixed as in repair complete all as specified and directed.

150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed as in repair complete all as specified and directed.

125mm long extruded aluminium alloy handles, cast type anodised (ISI marked) fixed as in repair complete all as specified and directed.

Door closer hydraulically cast iron body regulated designation No 3 universal type ,suitable for door shutter of 851 to 1000 mm in width and weight between 61 to 80 kg and fixed in repair complete all as specified and directed

15mm bore of pipe fancy type chromium plated stop cock cast copper alloy, screwed doen, high pressure, screwed bith ends for iron pipe or for unions ,with long shank and cup (concealed type) etc complete all as specified.

15mm bore chromium plated fancy type Bib taps, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fixed and including taking down old unserviceable taps complete all as specified and directed.

15mm bore fancy type chromium plated pillar taps with capstan heads, screwed down high pressure with long screwed sharks and fly nuts screwed down for iron pipes etc fixed as in repair complete all as specified and directed.

PVC connection suitable for 15mm bore with PTMT nuts of 450mm length including taking down old unserviceable complete all as specified and directed.

Waste coupling 32 mm dia of PTMT (half or full threaded) fixed as in repair complete all as specified and directed.

PVC (SWR) floor trap 75mm dia outlet plain with grating including jointing with solvent cement for trap fixed as in repair complete all as specified and directed.

15mm dia bib taps standered fency type PTMT (minimum weight 15mm-90gms) (Polytetra methylene terephthalate) with high pressure, screwed for iron pipe or for brass ferrule fixed as in repair complete all as specified and as directed.

15mm bore dia with long body bib tap standard of PTMT any colour high pressure screwed for iron pipe fixed as in repair complete all as specified and as directed.

15mm bore dia Pillar taps of PTMT anycolour high pressure screwed for iron pipe and fixed fixed as in repair complete all as specified and as directed.

Shower rose PTMT any colour (ISI marked) 195 mm long and 15mm dia with or without swivel joints , including fixing to steel pipe or union, supplied and fixed in repairs complete all as specified and as directed

Peg set 6 (Zinc), Cat Part No BEA-30 Prayag or equivalent fixed in repairs complete all as specified and as directed

Shelf of PTMT fixed with and including chromium plated screws and wooden/plastic cleats etc fixed in repairs complete all as specified and as directed

Liquid soap container of PTMT fixed with and including chromium plated screws and wooden/plastic cleats etc fixed in repairs complete all as specified and as directed

Tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges fixed as in repair complete all as specified and directed.

Welding in repair exceeding 2.5cm but not exceeding 5cm in length thickness of metal to be welded not exceeding 6mm complete all as specified and directed.

Taking down carefully and dismantling of ceiling fan/wall mounted fan/ pedestal fan/ exhaust fan of any make or model and sweep by opening the cover, separating down rod, rotor and stator assembly, locating the fault and making the fan fully in serviceable condition with & including replacing defective components such as bearing, rubber bush/bolt, gunmetal bush, capacitor burnt windings flexible cord, worn out screws of the cover, split pin, twin core flexible copper wire of size 23/0.0076, locking nuts & machine screws with spring washer for ceiling fan blades, oiling and greasing etc, reassembling & testing the fan complete all as directed. Note:- (i) Minor spare Parts i.e locking nuts & mechine screws with spring washer, bolt included in quoted rates. (ii) Spare Parts/accessories found unserviceable & required to be replaced shall be measured and paid for separately under relevant items as “Supply only”. (iii) Rewinding shall also be measured & paid for separately.

Rewinding of ceiling Fan of size 1200mm/1400mm sweep, 230 volts, 50Hz, AC including removal of existing burnt windings carefully from the slots, cleaning the slots thoroughly with necessary cleaning agent, applying slot insulation and rewinding the same with super enmelled copper winding wire of same gauge, same weight and same number of turns as that of existing and connecting the coils suitable to operate, capacitor type, tying the windings and applying air dry insulating varnish and drying the windings including replacing the defective components such as bearing, gun metal bush, rubber bush/bolt, capacitor, flexible cord, shaft and painting including assembling after lubricating movable components complete including testing complete all as specified and directed.

Rewinding of wall mounted Fan of size 450/550 mm sweep, 230 volts, 50Hz, AC including removal of existing burnt windings carefully from the slots, cleaning the slots thoroughly with necessary cleaning agent, applying slot insulation and rewinding the same with super enmelled copper winding wire of same gauge, same weight and same number of turns as that of existing and connecting the coils suitable to operate, capacitor type, tying the windings and applying air dry insulating varnish and drying the windings including replacing the defective components such as bearing, gun metal bush, rubber bush/bolt, capacitor, flexible cord, shaft and painting including assembling after lubricating movable components complete including testing complete all as specified and directed. Note:- Serial item No. 1.00 to 3.00 above bearing/Gunmetal bush/rubber bush bolt/capacitor/cord flexible wire/shaft/painting shall be measured and paid separately under respective items.

PVC flexible copper conductor, twin core size 23/0.0076 complete all as specified and directed.

Capacitor of 2.50 Mfd 440/500 volts suitable for ceiling Fan complete all as specified and directed.

Capacitor of 4.0 Mfd 440/500 volts suitable for Ceiling/Exhaust/Wall mounted Fan complete all as specified and directed.

Ball bearing suitable for Ceiling Fan of any Sweep any make / model complete all as specified and directed.

Ball bearing suitable for Exhaust Fan / wall mounted Fan any make / model / sweep complete all as specified and directed.

Exhaust fan motor suitable for exhaust fan of 300 mm sweep fixedas in repairs complete all as specified and directed

Exhaust fan motor suitable for exhaust fan of 450 mm sweep fixed as in repairs complete all as specified and directed

Exhaust fan PVC blade suitable for exhaust fan of 300 mm sweep fixed as in repairs complete all as specified and directed.

Gunmetal bush suitable for ceiling Fan/wall mounting Fan of any make/ model/ sweep of size 1200/1400mm and Exhaust Fan of any sweep all as specified and directed.

Rubber bush/bolt suitable for Ceiling Fan of any make/model /sweep of 1200/1400 mm all as specified and directed fixed as in repairs complete all as specified and directed.

Shaft suitable for ceiling fan / Exhaust fan/ wall mounted fan of any make/model and sweep with necessary machining work complete all as specified and directed.

Grouting in the bottom of the fan by lathe for fitting of bearing in bottom with bushing and all as directed.

Taking down copper/aluminium point wiring (light,fan,socket or power) complete, including fixture and fittings such as switches,ceiling roses, pendants, regulators, sockets, light fitting etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls,floors etc complete all as specified and directed. Note:- (i) Old dismantled wiring and accessories will be contractors property and credit will be charged against schedule of credit. (ii) Serviceable material will be reuse at site.

Taking down old seviceable distribution board of any size and any capacity including MCB abd MCCB's and making good, match the disturbed surfaces with existing surface complete all specified and directed. Note:- (i) Old dismantled wiring and accessories will be contractors property and credit will be charged against schedule of credit.

Point wiring for one light point controlled by one, one fan point controlled by one switch and regulator., one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC meduim duty casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS, terminated in & including factory made MS/pressed steel terminal box with zinc coated duly concealed in wall for mounting fittings like switches, sockets, fan regulators etc with and including 3mm thick plastic laminated sheet top cover, complete all as specified & directed.

All as per serial item No. 126.00 here-in-before but for one bell/buzzer point controlled by one bell push.

All as per serial item No. 126.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No. 126.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

Point wiring for one light point controlled by one, one way switch with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC meduim duty casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS, terminated in & including factory made MS/pressed steel terminal box with zinc coated duly concealed in wall for mounting fittings like switches, sockets, fan regulators etc with and including 3mm thick plastic laminated sheet top cover, including taking down old unserviceable point wiring complete all as specified & directed.

Ceiling rose surface bakelite 2 to 3 terminals 65x50mm fixed as in repair complete all as specified and directed.

Switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts (ISI Marked) fixed as in repair complete all as specified and directed.

Socket outlet 3 pin 5 Amps flush type (ISI Marked) fixed as in repair complete all as specified and directed.

Socket outlet 2 in 1, 6 pin 5 and 16 Amps flush type (ISI Marked) fixed as in repair complete all as specified and directed.

Switch piano type 230 volts, single pole one way 16 Amps, 230 volts (ISI Marked) fixed as in repair complete all as specified and directed.

Calling bell AC 230 volts type including necessary rectangular wooden block fixed as in repair complete all as specified and directed.

Bell push switch piano type (ISI Marked) fixed as in repair complete all as specified and directed.

Electronic fan regulator,Stepped type , flush type and connecting up, 120 watt, 240 volt (ISI marked) fixed as in repair complete all as specified and directed.

LED lights fitting 1x 16W, 220V, 4' long, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

LED lights fitting 1x 10W, 220V, 2' long, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Exhaust Fan 250mm sweep, BEE approved, ISI Marked with mounted in suitable opening arrangement with louvers shutters suitable for operation on 240 volts, single phase, 50 cycle per second, AC supply and connecting up including three core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2 mm drawn in flexible PVC conduit from ceiling rose or connector to fan including marking of MES number and fixed by using 4 Nos, bolts, nuts and washers and grouted in wall in CM 1:3 complete all as specified and directed.

Sub main wiring with 6.00 sqmm, two single core, PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 volts grade conforming to IS 694 including 6.00 Sqmm Single Core PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 Volt grade as continuous earth wire in green colour included PVC casing caping / conduit and taking down old unserviceable submain wiring complete all as specified. Note : Two run of 6.00 sqmm cable and one run of 6.00 sqmm cable as earth wire continuity conductor and PVC casing caping/ conduit shall be measured & paid as one unit.

Sub main wiring with 4.00 sqmm, two single core, PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 volts grade conforming to IS 694 including 4.00 Sqmm Single Core PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 Volt grade as continuous earth wire in green colour included PVC casing caping / conduit and taking down old unserviceable submain wiring complete all as specified. Note : Two run of 4.00 sqmm cable and one run of 4.00 sqmm cable as earth wire continuity conductor and PVC casing caping/ conduit shall be measured & paid as one unit.

Sheet metal enclosure factory made TPN 415 volt 4 way double door suitable for fixing MCB as outgoing and incoming MCCB 3 Pole, 63 Amps, repturing capacity 16 KA as main incoming duly painted including fixing of lugs in main incomming and outgoing line and fixing of cable glands of suitable size including grouting flush in the wall by means of nuts, bolts, angle iron and making good disturbed surfaces complete all as specified and directed.

Sheet metal enclosure powder coated single phase DB SPN 8 ways and neutal 250 Volts with 200 Amps rated bus bar double door suitable for fixing of MCBs including fixing of lugs in main incomming and outgoing line and fixing of cable glands of suitable size including grouting flush in the wall by means of nuts, bolts, angle iron and making good disturbed surfaces complete all as specified and directed.

MCB Single Pole with neutral 32 Amps, 240 Volts, repturing capacity 10 kA (ISI Marked) fixed as in repair complete all as specified and directed.

MCB Single Pole 5 to 32 Amps, 240 Volts, repturing capacity 10 kA (ISI Marked) fixed as in repair complete all as specified and directed.

LED security light 70 watt fixed as in repair complete all as specified and directed.

MCCB Triple Pole 63 Amps,420 Volts, repturing capacity 10 kA (ISI Marked) fixed as in repair complete all as specified and directed.

Supply and charging of refrigerant gas R-290/R-22/R-32 where required at site complete all as specified and directed.

Condenser Motor (Outdoor unit motor) of split type Air Conditioner of Capacity 1.5/2.0 TR inverter AC fixed as in repair including taking down of old unsv motor complete all as specified.

Condenser Motor (Outdoor unit motor) of split type Air Conditioner of Capacity 1.5/2.0 TR non inverter AC fixed as in repair including taking down of old unsv motor complete all as specified.

Blower Motor (Indoor unit motor) of split type Air Conditioner of Capacity 1.5/2.0 TR non inverter AC fixed as in repair including taking down of old unsv motor complete all as specified.

Blower Motor (Indoor unit motor) of split type Air Conditioner of Capacity 1.5/2.0 TR inverter AC fixed as in repair including taking down of old unsv motor complete all as specified.

Swing motor suitable for split air conditioner of capacity 1.5/2.0 TR invertor and non invertor type fixed as in repair including taking down old unsv complete all as specified and directed.

Servicing of split type Air Conditioner of capacity 1.5/2.0 TR of any type or make by opening the condenser unit fixed on roof top and cooling unit fixed inside the building, and cleaning the complete condenser unit and cooling unit including fins and checking / testing of all parts for its serviceability, and oiling/greasing of motors, replacing worn-out bushes of blower, rectification of unusual noise, checking of refrigerant standing pressure, topping of refrigerant upto the required level, replacement of minor parts such as nut/bolt washers etc. and reassembling of complete unit including testing for smooth functioning complete all as specified and directed. Note : (i) Refrigerant Gas required for topping up will be measured and paid separately as supply only under respective item of this Sch 'A' price schedule (ii) Any spare part of AC if found defective will be measured as supply and fix fixed in repairs under respective item of this Sch 'A' price schedule.

Suction lines copper pipes of suitable size as per site requirement fixed as in repair complete all as specified and directed.

Discharge lines copper pipes of suitable size as per site requirement fixed as in repair complete all as specified and directed.

Sleeve foam Protection suitable for Split type Air Conditioner 1.5/2.0 TR for both suction and discharge line fixed as in repair complete all as specified and directed.

Factory made PVC drain pipe suitable for Split type Air Conditioner 1.5/2.0 TR with coupler Joint fixed in repair complete all as specified and directed.

Running capacitor, 55+2.5/6 MFD and one point for blower motor suitable for Air Conditioner of capacity 1.5/2.0 TR fixed as in repair complete all as specified and directed.

Running capacitor, 45+2.5/4 MFD and one point for blower motor suitable for Air Conditioner of capacity 1.5/2.0 TR fixed as in repair complete all as specified and directed.

PVC fan blade suitable for condenser of split type Air Conditioner of any capacity of any type (Invertor or non invertor type) or make fixed as in repair complete all as specified and directed.

Condenser unit (outdoor unit) 1.5TR including taking down old unsv complete all as specified and directed.

Starting relay only suitable for window/split type Air Conditioner 1.5/2.0 TR capacity of any type or make fixed as in repair complete all as specified and directed.

Over load protector only suitable for window/split type Air Conditioner 1.5/2.0 TR capacities of any type or make fixed as in repair complete all as specified and directed.

Supply & installation of rotary compressor sealed unit for split type Air Conditioner of capacity 1.5/2.0 TR, (non invertor type) including testing for smooth functioning including taking down old unserviceable compressor complete all as specified and directed.

Supply & installation of rotary compressor sealed unit for split type Air Conditioner of capacity 1.5/2.0 TR, (invertor type) including testing for smooth functioning including taking down old unserviceable compressor complete all as specified and directed.

Evaporator unit (indoor unit) 1.5TR including taking down old unsv complete all as specified and directed.

Thermostat suitable for window/split type Air Conditioner 1.5/2.0 TR capacity fixed as in repair complete all as specified and directed.

Removing unserviceable window/split type Air Conditioner checking its leakage by filling of N2 gas, brazing and completely arresting its leakage, gas charging and testing complete all as specified and directed. Note : Gas charging shall be measured and paid separately.

Cooling coil suitable for window/split type Air Conditioner of capacity 1.5/2.0 TR including checking its leakage, brazing and completely arresting its leakage, gas charging and testing of any type or make fixed in repair complete all as specified and directed.

Wiring from indoor unit to outdoor unit of size 2.50 sqmm PVC insulated multistranded FRLS three core round cable including fixing of thimbles for fixing in compressor terminals for split type Air Conditioner 1.5/2.0 TR capacity inclduing taking down old unserviceable complete all as specified and directed.

Contactor 16 Amp, suitable for split/window type Air Conditioner upto 2.0TR fixed as in repair complete all as specified and directed.

Contactor 6 to 12 Amp,suitable for split/window type Air Conditioner upto 1.5 TR fixed as in repair complete all as specified and directed.

Over load relay 3 Pole, 5 to 16 Amps suitable for split/windwo type Air Conditioner upto 2.0 TR fixed as in repair complete all as specified and directed.

Universal Cordless Remote For any type of window/Split type Air Conditioner 1.5/2.0 TR fixed as in repair complete all as specified and directed.

Voltage stabilizer electronic type for automatic operation single phase naturally air cooled, indoor type, wall mounted for input variation between 170 V to 300 V with output voltage stabilized at 230V + 2.5% and of capacity 5.0 KVA complete all as specified and directed.

PCB Plate for electronic control suitable for Split type Air Conditioner of 1.5/2.0 TR capacity (non invertor type) any type of Make fixed as in repair complete all as specified and directed.

Repair of PCB Plate for electronic control suitable for Split type Air Conditioner of 1.5/2.0 TR capacity (non invertor type) any type / Make complete all as specified and directed.

PCB Plate complete set for indoor and outdoor unit for electronic control suitable for Split type Air Conditioner of 1.5/2.0 TR capacity (invertor type) any type of Make fixed as in repair complete all as specified and directed.

Repair of PCB Plate for electronic control suitable for Split type Air Conditioner of 1.5/2.0 TR capacity (invertor type) any type / Make complete all as specified and directed.

Metal claid Top Plug and socket of Capacity 20 Amp 240 volt (ISI Marked) fixed as in repair complete all as specified and directed.

Power socket 15 Amp suitable for metal clad box, ISI Marked including taking down old unserviceable complete all as specified and directed.

Power plug top, ISI Marked including taking down old unserviceable complete all as specified and directed.

Factory made bracket with powder coated, fixed on wall with necessary grouting MS nut, bolt and washer or fastener as per site requirement for installation of outdoor unit of 1.5/2.0 TR split AC and making good disturbed surfaces, including taking down of old u/s bracket complete all as specified and directed.

Capillary of size 31, 36, 40, 50 & 80 No including taking down old unsv complete all as specified and directed

Suction line brass valve suitable for split air conditioner of capacity 1.5/2.0 TR complete all as specified and directed.

Discharge line brass valve suitable for split air conditioner of capacity 1.5/2.0 TR complete all as specified and directed.

PTFE Thread Seal Tape 12mmx10m complete all as specified and directed.

Servicing of water cooler, Refrigerator and Deep Freezer of any type or make by opening and cleaning the complete body and checking / testing of all parts for its serviceability and oiling / greasing of motors, replacing worn-out bushes of fan motor, rectification of unusual noise, checking of regrigerant standing pressure, topping of refrigerant upto the required level, replacement of minor parts such as nut / bolt washers etc. and reassembling of complete unit including testing for smooth functioning complete all as specified and directed. Note :-(i) Refrigerant Gas required for topping up will be measured and paid separately as supply only under respective item of this Sch 'A' price schedule.

Comprehensive maintenance and servicing including testing of RO Plant of capcity (01 No) including washing, cleaning, sedimentation, filteration, disinfection process, pressure pumping set & chlorine dosing unit at AF Stn Ramgarh area so as to supply qualitative water at permissible level of TDS complete all as specified and directed. Note : Spares required for replacement will be measured and paid seperately under respective items here-in-this schedule.

Water flow meter (rotameter) suitable for RO Plant of capacity 1000 Litre/hour fixed as in repair complete all as specified and directed.

Supply only Jambo micro filter candle for RO Plant (threaded), 4.50" (Inches) wound complete as per sample all as specified and directed

Supply only antiscalant soluton (suitable for RO plants) complete all as specified and directed.

Membrane suitable for RO Plant, flow 250 LPH, rejection (%) : 99.67, Model No. CPA2-4040 Nitto of Hydranautics or equivalent of Daw/GE, fixed as in repair complete all as specified and directed.

Dozing pump feeder for injecting PH booster, Antiscalent, chlorine with dosing Rate : 6 LPH @ 4 Kg/Sqcm, 400 Max Stroke/ Minute fixed as in repair complete all as specified and directed. Make: Aqua/Aventura or equivalent.

Disconnection of all pressure tubes from the RO Plant and taking out all membranes from pressure tubes cleaning the same with citric acid (low pH) and solium hyppchloride (high pH) and complete washing with RO water and re-assembling the same complete all as specified and directed.

UV Lamp for capacity 20 watt for UV Filter sutiable for RO of capacity 1000 LPH fixed as in repair complete all as specified and directed.

Plastic cylindrical sealed disposable sanitiser refill for disinfection of drinking water with arrangement for controlled release of disinfectant in water, suitable for operation through suitable feeder in pressurised line stequa 411E fixed as in repair complete all as specified and directed. Make: Declibac,Potter & Watts/Brio Zing or equivalent

Galvanized steel water tubing medium grade of 25 mm bore with & including all fittings fixed to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing , complete all as specified and directed.

Galvanized steel water tubing medium grade of 40 mm bore with & including all fittings fixed to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing , complete all as specified and directed.

Galvanized steel water tubing medium grade of 50 mm bore with & including all fittings fixed to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing , complete all as specified and directed.

Galvanized steel water tubing medium grade of 80 mm bore with & including all fittings fixed to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing , complete all as specified and directed.

80 mm dia Gun metal gate valves with iron wheel head, screwed both ends for iron pipes fixed as in repair complete all as specified and directed.

50 mm dia Gun metal gate valves with iron wheel head, screwed both ends for iron pipes fixed as in repair complete all as specified and directed.

40 mm dia Gun metal gate valves with iron wheel head, screwed both ends for iron pipes fixed as in repair complete all as specified and directed.

25 mm dia Gun metal gate valves with iron wheel head, screwed both ends for iron pipes fixed as in repair complete all as specified and directed.

20 mm dia Gun metal gate valves with iron wheel head, screwed both ends for iron pipes fixed as in repair complete all as specified and directed.

15 mm dia Gun metal gate valves with iron wheel head, screwed both ends for iron pipes fixed as in repair complete all as specified and directed.

Cast iron body Sluice valve heavy duty class ‘PN-1.6’, 80mm bore, ISI marked with confirming to IS-14846-2000, both flanged ends and drilled, high tensile stainless steel spindle, Cast Iron gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable of existing sluice valve, complete all as specified and directed.

Cast iron body sluice valve heavy duty class ‘PN-1.6’, 100mm bore, ISI marked with confirming to IS-14846-2000, both flanged ends and drilled, high tensile stainless steel spindle, Cast Iron gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable of existing sluice valve complete all as specified and directed.

Cast Iron foot valve of size 50mm bore (ISI marked) flanged end/threaded type (heavey grade) with rubber insertion sheet 3mm thick, nuts, bolts and washers including taking down old existing unserviceable foot valve complete all as specified & directed.

Cast Iron foot valve of size 80mm bore (ISI marked) flanged end/threaded type (heavey grade) with rubber insertion sheet 3mm thick, nuts, bolts and washers including taking down old existing unserviceable foot valve complete all as specified & directed.

Preparation/cleaning of old painted steel surface of any description such as suction line, delivery line, priming line or any other pipe line/channel plates complete with scraping out old painted surface and after that marking of flow direction along with painting as per colour code complete all as specified and directed.

Centrifugal/Monoblock Pump motor MS coupling capacity 15 HP motor (Beam, Jaw, Gear any type) fixed as in repair complete all as specified and directed.

HDPE foot valve suitable for 150 mm suction pipe along with flentch ,nut, bolt and washers complete all as specified and directed.

Rectification of leakaging in water main pipe line by necessary excavation (upto one length of 6.00 RM) in any type of soil, in any situation/depth including bailing out leakage water by suitable measures, repair to existing DI/CI pipe line following sizes by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn, lead wool ring etc and testing of joint including dewatering complete all as specified and directed. Note: Cost of JCB for lifting of pipe for repair will be part of quoted rates by the tenderer.

80mm bore CI/DI Pipe lines

100mm bore CI/DI Pipe lines

Rectification of leakage in water main pipe line including necessary excavation in any type of soil, in any situation including bailing out leakage water by suitable measures, repair to existing Galvanised Iron pipes lines following sizes and cutting threading, for addition & alternation and for insertion of fittings/accessories (bend, elbow & Tee) complete all as specified and directed. Note:- (i) The rate is deemed to include for one fitting/special (complete unit) as required at site. (ii) Rate quoted shall be deemed to be inclusive of necessary dewatering and excavation (Upto one length of 6 RM) filling making good the existing surfaces with the necessary T&P, accessories of appropriate size as required complete all as directed.

15/20mm bore GI Pipe lines

25mm bore GI Pipe lines

40mm bore GI Pipe lines

50mm bore GI Pipe lines

80mm bore GI Pipe lines

Testing of RO water sample for chemical examination of drinking water (such as coliform bacteria, nitrates, pH value, sodium, chloride, fluoride, sulphate, iron magnase, hardness etc) by authorised government laboratory complete for SMQ RO plant, 15 AFH RO plant, Chandan RO plant and Ramgarh RO plant all as specified and directed. Note: Water sample collect and testing to be done every quarterly basis (03 months) and report of the same to be submitted to Engineer-in-Charge and GE.

Cuttings grass/herbs near installation, plant and pumps complete cleaning of installation, valve chamber and cleaning of installation including necessary tools and safety measures where ever complete all as specified and directed.

shivam electricals and engneers

prem enterprises

Manisha Enterprises

SHRI HARI CONSTRUCTION

S R ENTERPRISES

M/s Shree Construction Company