SPECIAL REPAIR TO type II QTRS (P-10) AT CGRA KOCHI.

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding and removing rubbish off the premises complete all as specified and as directed.

Demolition of un-reinforced cement concrete of any description as in roof/landing/chajja/shelves and similar suspended work other than ground floor including taking down old roof tratment complete all as specified and directed.

Material and labour for Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and directed.

Material and labour for Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m complete all as specified and directed.

Material and labour for providing cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate cast in situ as in kerbs or mud stops, rounded or chamfered on edges, as directed including use of form work as necessary all as specified and as directed.

Material and Labour for Non-skid light coloured Ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not excceding 0.11 Sqm, in floors etc, set and jointed in cement mortar and pointed in white or coloured cement to match, laid over and including 20 mm thick screed bed in CM 1:4 complete all as specified and as directed.

Material and Labour for Non-skid light coloured Ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not excceding 0.18 Sqm, in floors etc, set and jointed in cement mortar and pointed in white or coloured cement to match, laid over and including 20 mm thick screed bed in CM 1:4 complete all as specified and as directed.

Material and labour for glazed ceramic coloured tiles in vertical surface such as dado, size of tile 300x200x7mm set and jointed in neat cement slurry fixed over backing coat of 10mm thick in CM 1:4 complete all as specified and directed.

Demolition of un-reinforced concrete in ground floors, pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Material and labour for 100mm thick plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in sub base of floors including necessary form work all as specified and as directed.

Material and labour for machine pressed precast concrete interlocking paver block, any shape and size of 80mm thickness M-40 grade conforming to IS 15658-2006 with grey cement and pigment laid over and including 50mm thick sand cushioning, compacted with mechanical surface vibrator and with scratch proof lacquer coating on top surfaces complete all as specified and directed.

Material and labour for Plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in copings, kneelers, apex stones,bed plates, kerbs, bed block for hold fast including necessary form work all as specified and as directed.

Material and Labour for 75mm thick Plain Cement Concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection, floors, pavings and hardstanding etc, finished even smooth without using extra cement etc including necessary forwork complete all as specified and as directed.

Dismantling of Stone slabs and granite laid, bedded and pointed in any mortar of any description or thickness in floors, aprons cills or platform etc complete all as specified and as directed.

Material and Labour for Granite 20mm thick ( of any type table rubbed and polished) work machine cut as in steps, jambs pillars,window cills, cooking platforms and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of granite and laid over and including 15mm thick cement mortar 1 :4 complete all as specified and directed.

Material and labour taking down chowkhats or frames, without taking off shutters from the frame exceeding 1.5 Sqm but not exceeding 4 sqm in each and removing as directed.

Material and labour taking down chowkhats or frames, without taking off shutters from the frame not exceeding 1.5 Sqm in each and removing as directed.

Taking down shutter of any description exceeding 1 sqm but not exceeding 2 sqm each and removing from site complete all as specified and directed.

Supply and Fix PVC door frame size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges will be painted to match with prelaminated sheet reinforced with MS square tube supplying & fixing in opening as per specification complete all as specified and directed.

Supply and Fix factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with wood free EPS supplying & fixing in frame at site as per specification and drawing given in SSR Part-II complete all as specified and as directed.

Material and labour for second class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with shine pinned at joints, fixed to wall and making good to wall all as specified and directed.

Supply and fix mild steel Flat for hold fast, cleat etc. for door frame etc. conforming to Fe 290, Gde E-165 complete all as specified and as directed.

Supply and fixing 2nd class hardwood factory made plain framed panelled shutters 35mm thick with lock rail and with panels of timber flat on both edges(feather edged) or 12mm thick commercial veneered particle board veneers on both side or with 9mm thick BWP commercial ply, size of members of shutters as specified in IS 1003-Part-I, kiln seasoned and chemically pressure treated complete all as specified and as directed.

Supply and Fix 1st class HW glazed and skeleton shutters 35mm thk, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

Supply and Fix stainless steel wire cloth 0.36mm nominal dia of wire and average widht of aperature 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fix aluminium powder coated frame for doors,windows, ventilators with one or more rebates with joint clip and using rubber beading etc complete all as specified and directed. Note : Glass panel/particle board panel filling shall be measured and paid separately.

Supply and fix for powder coated, Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

Supply and Fixing 5.5 mm thick tinted sheet glass ordinary quality in square not exceeding 0.5 Sqm in each pane for fixing in aluminium joinery with rubber gasket as specified and as directed.

Supply and fix 100mm long butt hinges medium weight mild steel cold rolled complete all as specified and as directed.

Supply and fix 75mm long butt hinges medium weight mild steel cold rolled complete all as specified and as directed.

Supply and Fix 150mm long aluminium handle fabricated type anodised all as specified and as directed by Eng-in-charge.

Supply and fix aluminium handles fabricated type anodised of size 100mm complete all as specified and as directed.

Supply and Fix 150mm long aluminium anodised barrel tower bolt all as specified and as directed by Eng-in-charge.

Supply and Fix 100mm long aluminium anodised barrel tower bolt all as specified and as directed by Eng-in-charge.

Supply and fixing aluminium alloy,anodised, sliding door bolt of length 250mm with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded section or cast-aluminium alloy complete all specified and as directed.

Supply and fixing in repairs harrison rail, mild steel, chromium plated nwith fixing bracket, stops, rollers etc complete all as specified and as directed.

Supply and fixing second class soft wood scantling (clean sawn) framed work, fixed with nails all as specified and as directed all as specified and directed.

Supply and fixing 2nd class soft wood plain fillets, square rectangular or triangular in section exceeding 13 Sqcm & not exceeding 25 Sqcm clean sawn, secured with nails or brads all as specified and as directed

Supply and fixing 2nd class soft wood plain fillets square/rectangular wrought bullnosed, splayed, chamferred or rounded of sectional area n. exc. 3 sqcm complete all as specified and as directed.

Supply and fix 18/19 mm thick prelaminated particle board, interior grade, pr lamnated one side with decorative choice lamination other side balancing white lamination fixed with screws to frame work including taking down unserviceable old particle board complete all as specified and as directed.

Material and Labour applying two coats synthetic enamel paint over one coat of pink primer on wooden surface any description over 10 cm in width or girth not otherwise described including preparation of surface etc., complete all as specified and directed.

Material and labour for preparation of old decorated wooden surfaces of any description exceeding 10 cm width or grith not otherwise specified and applying one coat of syntheic enemal paint all as specified and as directed.

Material and labour for preparation of old decorated surfaces of steel of any description exceeding 10 cm width or grith not otherwise specified and applying one coat of syntheic enemal paint all as specified and as directed.

Taking up or down steel tubing 15 mm bore including connections, cleaning for refixing or removal to store all as directed.

Taking up or down steel tubing 20 mm bore including connections, cleaning for refixing or removal to store all as directed.

Supply and fixing galvanised steel tubing medium grade 15 mm bore with all fittings and fixed complete to walls/ceiling/floors all as specified and as directed.

Supply and fixing galvanised steel tubing medium grade 20 mm bore with all fittings and fixed complete to walls/ceiling/floors all as specified and as directed.

Supply and fixing in repairs Vitrious China squatting pan ' Orissa' pattern of size 580 mm x 440 mm white with integral foot rest excluding flushing cistern and flush pipe including P or S trap making good the floor to match with existing floor complete all as specified and as directed.

Supply and Fix in repair PVC valveless, syphonic action type, flushing cristern, low level, white, 10 ltr capacity with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

Supply & Fixing in repairs Bib taps, 15mm bore, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

Supply and Fixing in repairs stop valves/angle cock, 15mm bore, fancy type, with long shank & cut concealed type chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fix in repair 15mm dia PVC connection with PTMT nuts and PVC washers 45 cm long and connecting of water pipes all as specified and directed.

Supply and fixing in repairs vitreous China wash hand basin, white, flat back size 550X400mm including 32mm brass chromium plated waste fitting, a pair of cast iron bracket duly painted including cutting and pinning in ends making good disturbed surfaces in CM 1:3 excluding pillar tap but chain , plug and porcelain stopper, brackets etc all as specified and as directed.

Supply and fixing in repairs pillar taps, cast copper alloy with capstan heads, chromium plated,fancy type screwed down, long shank, and fly nut, high pressure, screwed for iron pipe of 15 mm bore all as specified and as directed.

Supply and fix sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers, and wastes, including bedding in cement mortar to drawf wal or including fixing cantiliver brackets and connecting union ot pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm all as specified and as directed.

Supply and fixing Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40 gms) all as specified and as directed.

Supply and fixing in repairs Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) all as specified and as directed.

Supply and fixing in repairs 6 mm thick bevelled edge looking mirror of size 600 x 450 mm mounted on 6 mm thick AC Building board or commercial plywood/hard board backing and fixed to wooden plugs with CP Screws and cup washers all as specified and as directed.

Supply and fixing in repairs Towel rails tubular brass chromium plated 20 mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

Supply and fix PVC pipe (SWR) single socketed in any length with rubber ring joint 110mm dia fixed to wall complete all as specified and as directed.

Supply and fix PVC pipe (SWR) single socketed in any length with rubber ring joint 75mm dia fixed to wall complete all as specified and as directed.

Supply and fix PVC (SWR) bends 110mm with access door complete all as specified and as directed.

Supply and fix PVC (SWR) bends 75mm with access door complete all as specified and as directed.

Supply and Fix PVC (SWR) junction single 110 mm bore, (single T) equal or unequal with access door complete all as specified and as directed.

Supply and fix in repairs 75mm PVC (SWR) branch piece , single (Double Y) equal or unequal all as specified and as directed.

Supply and Fix PVC (SWR) vent cowl 110mm bore without access door complete all as specified and as directed.

Supply and fix PVC (SWR) vent cowl 75mm complete all as specified and as directed.

Demolition of brick or stone masonry built in cement mortar including all quoins,arches, pillers etc but excluding ashlar facings,dressed stone work and precast concrete articles complete all as specified and as directed.

Material and labour for Precast cement concrete solid block masonry using soild PCC block grade C4, exceeding 10 cm in width and built in cement mortar 1:4 complete all as per specified and as directed.

Taking down cement plastering on concrete or Brick works surface racking out joints, hacking for key , scrubbing down with water, remove dust, debries/rubbish etc. complete all as specified and as directed.

Material and Labour for 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth with out using extra cement complete all as specified and as directed.

Material and Labour for rendering 15mm thick on fair faces of concrete work in CM 1:4, using water proofing compound @3% by weight of cement, finished even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound shall be measured separately.

Supply only integral water proofing compound all as specified and as directed.

Material and labour for preparation of of new plastered/concrete surfaces of walls and applying two coats of acrylic distemper of approved shade/tint over a coat of primer, over 3mm thick wall care putty finish to achieve uniform smooth surface of wall all as specified and as directed.

Material and labour for preparation of old distempered wall surfaces by washing, rubbing down and stopping the surfaces and applying Two coat of acrylic distemper applied to walls of up to 4 storied buildings complete all as specified and directed

Material and Labour for preparation of old decorated surfaces of ceiling/ soffits of chajja & canopy by brooming down with wire brushing or scrapping down smoke soot, moulds, mass and effloroscent salts and applying two coat of white wash upto 4th storey height, complete all as specified and as directed.

Material and labour for for applying two or more coats of 100% premium acrylic emulsion paint having VOC not less than 50 gm/lit and UV resistance as per IS 15489-2004, dust, alkali and fungal resistant, of approved shadewith silicon additives @ 1.43 lit/10Sqm over a coat of primer @ 0.9Lit per 10 Sqm complete all as specified and as directed.

Excavating in trenches, n exc1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil getting out complete all as specified and as directed.

Material and labour for plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete including necessary form work complete all as specified and as directed.

Demolition and breaking up 150mm bore drain pipes (RCC pipe/Salt glazed ware or Reinforced concrete) set in cement mortar including haunching and removing debris to a distance exc 1.5Km and n.exc 5Km all as specified and as directed.

Material and Labour for PCC 1:3:6, type C-2 as in concrete bed to drain pipes including packing under and completely surrounding pipes after they are laid and tested for 150mm dia pipe and testedcomplete all as specified and as directed.

Supply and laying salt glazed stone ware drain pipe 150 mm dia, grade 'A', laid in trenches, on concrete bed or directly on hard grounds as indicated and jointed with cement mortar 1:1 and testing complete all as specified and as directed.

Material and Labour for TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wires (annealed) not less than 0.9 mm dia or secured with clips complete all as specified and as directed.

Material and labour for Precast reinforced cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in cover slabs of man holes including necessary form work, placed in position, set in CM 1:4 complete all specified and as directed.

Returning, filling in soil including spreading leveling, watering and well ramming in layers n.exc.25cm thick complete all as specified and as directed.

Removing excavated material / soil to a distance n.exc 50m away and depositing where as directed at a level n.exc 1.5m above the starting point, complete all as specified and as directed.

Material and labour for Plain cement concrete 1:3:6, type C2, using 40mm graded stone aggregate as in surface channels and drains including necessary form work all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms moulds, mitred/stopped ends etc complete all as specified and directed.

Dismantling of water tanks of capacity exceeding 250 ltrs and not exceeing 500 ltrs capacity and removing from site complete all as specified and as directed by Engineer-in-charge.

Supply and fix Rotational moulded Polyetheylene Water Storage Tank 500 Ltr capacity Triple Layer (Cylinderical verticle with closed top) including 15mm dia GI Medium Grade 200mm long overflow and wash out pipe each with all required fittings, Checknut, Stopper etc complete hoisted and fixed in position, including all incoming and outgoing connection of GI pipe complete and including 20mm PTMT Ball valves high pressure wiith epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete for 15mm dia pipe (Minimum weight 15mm- 142 gms/each) fixed on roof top complete all as specified and directed.

Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for unreinforced complete all as specified and as directed.

Material and Labour for rendering 10mm thick on fair faces of concrete work in CM 1:3 mixed with integral water proofing compound @ 3% by weight of cement or as per manufacturers instruction, surface finished even & smooth without using extra cement including curing the plastered surface complete all as specified and directed. NOTE: Water proofing compound shall be measured and paid separately.

Material and labour for plain cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in kerb, mud stop rounded or chamferred edges including use of form work as necessary complete all as specified and as directed.

Material and labour for applying oil based bitumen primer conforming to IS 3384-1986 at 0.20 kg/Sqm on prepared surface and applying of one coat of blown grade hot bitumen 85/25 conforming to IS 702 @ 1.20 kg / sqm and applying roof treatment with APP modified waterproofing membrane weighing not less than 3kg/sqm, reinforced with non woven polyster matt weighing not less than 160 gm/sqm having softening point not less than 140 degree centigrade, longitudinal tensile strength not less than 650N/Sqm cm, tearing strength of 180N(Minimum), applied by torch-on application including minimum 10 cm over lap and 15 cm end lap and applying of one coat of blown grade hot bitumen 85/25 conforming to IS 702 @ 1.20 kg / sqm over the membrane and then applying solar reflective bituminous aluminium paint for thermal insulation @ 0.10 kg/sqm complete all as specified and directed. NOTE:All necessary safety measures shall be ensured by the contractor during execution of work at site and quoted rate shall be deemed to be inclusive of the same.

Use and waste for form work to sides of concrete surfaces of columns/pillars, square or rectangular in plan, fair finshed surfaces all as specified and as directed.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams to rough finished surface of concrete for flat complete all as specified and as directed.

Material and Labour for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wires (annealed) not less than 0.9 mm dia or secured with clips complete all as specified and as directed.

Material and labour for TMT bars(CRS/HCR), 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

Material and labour for Reinforced cement concrete M-30 design mix using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc all as specified and as directed.

Material and labour for reinforced cement concrete design mix M-30 using 20 mm graded granite stone aggregate as in beams, cantilevers, lintel over 1.5M span all as specified and as directed.

M & L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Taking down carefully (copper/aluminum) point wiring complete of any type (batten/surface conduit) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants regulators etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster or tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as specified and directed.

Material and Labour for point wiring complete using 1.5 Sqmm PVC insulated unsheathed copper conductor, stranded cable (FRLS) upto and including working voltage 1100volts grade, drawn through and including PVC casing and caping including all accessories ISI marked including press fit white PVC open switch/surface board high strength and crack resistance and unsheathed copper conductor stranded cable (FRLS) earth continuity wire connected to DBs/sunken boxes/fittings of size 1.5 Sqmm Cross sectional area and all other metal parts with earth dolly for the following:-. (a ) one light point controlled by one switch 5 Amps

(b ) one fan/ exhaust fan point point controlled by one switch 5 Amps

(c) One bell point controlled by one bell push

(d ) One 3 pin socket outlet 5 Amps on same board

All as per Item No. 103 above but with 4 sq mm PVC insulated copper conductor cable(FR) including 4 sq mm PVC copper conductor used as earth wire for power point on independent board for One 3 pin socket outlet, 15 Amps.

Supply and fixing in replacement of Modular switch, one way, 6Amps, one module complete all as specified.

Supply and fixing in replacement of Modular socket outlet, 6 Amps, 2 and 3 pin combined two modules complete all as specified.

Supply and fixing in replacement of Modular switch socket combination 16 A 6 pin 3module complete all as specified and directed.

Supply and fixing in replacement of Modular fan regulator step type, 120 Watt complete all as specified and directed.

Supply and fix in replacement of Bell electric Ding Dong 230 Volts, AC, with ISI mark complete all as specified and directed.

Supply and fixing in replacement of Modular Bell push, 6 Amps complete all as specified and directed.

Supply and fix in replacement of Ceiling rose in poly carbonate 3 plates flush type 6 Amps, 230 volts AC complete all as specified and directed.

Material and labour for Sub main wiring using two runs of single core PVC insulated cable (FRLS) 6 sqmm copper conductor multi stranded and one run of 6 sqmm copper conductor insulated cable (FRLS)using as earth wire drawn through and including suitable size PVC casing and caping including taking down old aluminium/Copper Sub main wirng complete all as specified and directed. Note- 3 run of 6 sq mm PVC copper wire and One run of PVC casing caping shall be measured and paid as one unit.

Supply and fix in repairs Distribution board (DB) made out of sheet metal enclosure (CRCA sheet), dust and vermin proof, SPN 12 way with 200 Amps rated copper bus bar double door protection, neutral bar,earth bar, single pole and neutral 240 volts, MCBs used as incommer Double door, flush to wall complete all as specified and directed .

Supply and fix in repairs MCB single pole & neutral 240 volt C curve 10 KA 40 Amps capacity IP 20 transparent lebel holder fully insulated safety shutters complete including suitable size copper lugs complete all as specified and directed.

Supply and fix in repairs MCB SP, 240 Volts, 6 to 32 Amps, breaking capacity of 10 KA, 'C' Curve complete all specified and as directed.

Supply and fix, connecting and testing RCCB, AC, 2 Pole 40 Amp, breaking capacity 100 mA complete all as specified and as directed.

Supply and fix in repairs LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make : Havells / Crompton Greaves / Philips / Wipro/ Bajaj

Supply and fix in repairs LED light fitting mirror type with high out put diffuser 2 feet,10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make : Havells / Crompton Greaves / Philips / Wipro/ Bajaj

Supply and fix in repairs LED decorative wall light fitting made up of extruded polycarbonate, envirnmentl friendly, energy efficient ready to use pack, suitable for 1x40 watts LED lamp E27 base including accessories prewired and connecting up complete all as specified and as directed. Make : Havells / Crompton Greaves / Philips / Wipro/ Bajaj

Supply and fix in repair Exhaust Fan of size 300 mm sweep with louvers, with plastic body AC 230 V, 50 Hz, and connecting to ceiling rose terminals with 23/.0076 flexible cable and making good the disturbed surface to match with existing finishes complete all specified and directed.

Schedule of Credit (Minus) Rs.75022.00 NOTE: Bidder shall insert credit amount of Rs. 75022.00 as rate in Green field under Col-13.

MS BUILDERS