SDRF-Mech Sub Dvn Mpza- Flood damages- Urgent Repair works to the sluices in Cheruvanchippadam branch canal

Amount

SCHEME- 1 - Cheruvanchippadam branch canal - B/W ch. 0/000km to 0/300 km

od16863/2019_2020/MH : Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od16864/2019_2020/MH : Fabrication, supply and erection in correct position and alignment SS 304L grade plate for CANAL GATE

od16865/2019_2020/MH : Fabrication, erection and commissioning of STRUCTURAL MILD STEEL EMBEDDED PARTS for CANAL GATES

od16866/2019_2020/MH : Fabrication and supply of STRUCTURAL STEEL CANAL GATE and its accessories

od16867/2019_2020/MH : Fabrication and supply of HOISTING UNIT for CANAL GATE in structural steel

od16868/2019_2020/MH : Providing Base & Nut arrangement for hoisting the shutter including cost of all materials, labour charges etc complete

od16869/2019_2020/MH : Cost of supping and fixing of Screw rod LOCKING ARRANGEMENT including cost of materials labour and conveyance complete

od16870/2019_2020/MH : Providing EN-8 SQUARE THREADED SCREW ROD of dia 63mm (per metre rate)

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od16871/2019_2020/MH : ERECTION of the CANAL GATE safely in the grooves

od16872/2019_2020/MH : ERECTION of the HOISTING UNIT and its ACCESSORIES

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

SCHEME- 2 -Cheruvanchippadam branch canal - B/W ch. 0/300km to 0/600 km

od16863/2019_2020/MH : Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od16864/2019_2020/MH : Fabrication, supply and erection in correct position and alignment SS 304L grade plate for CANAL GATE

od16865/2019_2020/MH : Fabrication, erection and commissioning of STRUCTURAL MILD STEEL EMBEDDED PARTS for CANAL GATES

od16866/2019_2020/MH : Fabrication and supply of STRUCTURAL STEEL CANAL GATE and its accessories

od16867/2019_2020/MH : Fabrication and supply of HOISTING UNIT for CANAL GATE in structural steel

od16868/2019_2020/MH : Providing Base & Nut arrangement for hoisting the shutter including cost of all materials, labour charges etc complete

od16869/2019_2020/MH : Cost of supping and fixing of Screw rod LOCKING ARRANGEMENT including cost of materials labour and conveyance complete

od16870/2019_2020/MH : Providing EN-8 SQUARE THREADED SCREW ROD of dia 63mm (per metre rate)

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od16871/2019_2020/MH : ERECTION of the CANAL GATE safely in the grooves

od16872/2019_2020/MH : ERECTION of the HOISTING UNIT and its ACCESSORIES

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

SCHEME-3 - Cheruvanchippadam branch canal - B/W ch. 0/600km to 0/900 km

od16863/2019_2020/MH : Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od16864/2019_2020/MH : Fabrication, supply and erection in correct position and alignment SS 304L grade plate for CANAL GATE

od16865/2019_2020/MH : Fabrication, erection and commissioning of STRUCTURAL MILD STEEL EMBEDDED PARTS for CANAL GATES

od16866/2019_2020/MH : Fabrication and supply of STRUCTURAL STEEL CANAL GATE and its accessories

od16867/2019_2020/MH : Fabrication and supply of HOISTING UNIT for CANAL GATE in structural steel

od16868/2019_2020/MH : Providing Base & Nut arrangement for hoisting the shutter including cost of all materials, labour charges etc complete

od16869/2019_2020/MH : Cost of supping and fixing of Screw rod LOCKING ARRANGEMENT including cost of materials labour and conveyance complete

od16870/2019_2020/MH : Providing EN-8 SQUARE THREADED SCREW ROD of dia 63mm (per metre rate)

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od16871/2019_2020/MH : ERECTION of the CANAL GATE safely in the grooves

od16872/2019_2020/MH : ERECTION of the HOISTING UNIT and its ACCESSORIES

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

SCHEME -4 -Cheruvanchippadam branch canal - B/W ch. 0/900 km to 1/200 km

od16863/2019_2020/MH : Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od16864/2019_2020/MH : Fabrication, supply and erection in correct position and alignment SS 304L grade plate for CANAL GATE

od16865/2019_2020/MH : Fabrication, erection and commissioning of STRUCTURAL MILD STEEL EMBEDDED PARTS for CANAL GATES

od16866/2019_2020/MH : Fabrication and supply of STRUCTURAL STEEL CANAL GATE and its accessories

od16867/2019_2020/MH : Fabrication and supply of HOISTING UNIT for CANAL GATE in structural steel

od16868/2019_2020/MH : Providing Base & Nut arrangement for hoisting the shutter including cost of all materials, labour charges etc complete

od16869/2019_2020/MH : Cost of supping and fixing of Screw rod LOCKING ARRANGEMENT including cost of materials labour and conveyance complete

od16870/2019_2020/MH : Providing EN-8 SQUARE THREADED SCREW ROD of dia 63mm (per metre rate)

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od16871/2019_2020/MH : ERECTION of the CANAL GATE safely in the grooves

od16872/2019_2020/MH : ERECTION of the HOISTING UNIT and its ACCESSORIES

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

SCHEME-5 - Cheruvanchippadam branch canal - B/W ch. 1/200 km to 1/450 km

od16863/2019_2020/MH : Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

od16864/2019_2020/MH : Fabrication, supply and erection in correct position and alignment SS 304L grade plate for CANAL GATE

od16865/2019_2020/MH : Fabrication, erection and commissioning of STRUCTURAL MILD STEEL EMBEDDED PARTS for CANAL GATES

od16866/2019_2020/MH : Fabrication and supply of STRUCTURAL STEEL CANAL GATE and its accessories

od16867/2019_2020/MH : Fabrication and supply of HOISTING UNIT for CANAL GATE in structural steel

od16868/2019_2020/MH : Providing Base & Nut arrangement for hoisting the shutter including cost of all materials, labour charges etc complete

od16869/2019_2020/MH : Cost of supping and fixing of Screw rod LOCKING ARRANGEMENT including cost of materials labour and conveyance complete

od16870/2019_2020/MH : Providing EN-8 SQUARE THREADED SCREW ROD of dia 63mm (per metre rate)

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od16871/2019_2020/MH : ERECTION of the CANAL GATE safely in the grooves

od16872/2019_2020/MH : ERECTION of the HOISTING UNIT and its ACCESSORIES

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Bidder Name

ASHIFUL HAK.C