SPECIAL REPAIRS TO BLDG NO E 16 OTM ACCN AT 7 ENGR AND PROVN OF SEPTIC TANK ALONG WITH SOAKAGE WELL NEAR BLDG NO J 157 UNDER AGE B R N NO I OF GE N SECUNDERABAD

Amount

Taking down of old bituminous tarfelt or any other type of roof treatment from roof/ concrete surfaces and cleaning of the roof surface with wire brush to make it free from dust, dirt etc including removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided in roof padding concrete etc including removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

M&L PCC (1:2:4) Type B0 (using 12.5 mm graded stone aggregate) with using water proofing compound @ 2% by weight of cement or as per manufacturer's instructions as in levelling course, haunching, coping and similar works over RCC roof surface and RCC over head tank top surface including rounded or chamferred on edges and formwork etc complete all as specified and directed. Note: Water proofing compound will be measured and paid separately

M&L Rendering 10mm thick CM (1:4) on roof surfaces duly mixing with water proofing compound at the rate of 2% by weight of cement and finished even and smooth complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately

Supply only water proofing compound

M & L Providing water proofing treatement with APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick reinforced with polyester non oven fabric ( weight not less than 150gm/Sqm) applyied on one coat of oil based bitumen emulision primer @ 0.3 lit per sqm ( OR as per the directions of manufacturer instructions) including cleaning of surface thoroughly from dust, dirt and projections. Laying of membrane by forced ( torch) application with 10cm overlaps . A coat of blown bitumen 85/25 grade @ 1.2 Kg/sqm to be applied on top of memberane, finally coating the surface with bituminous aluminium paint @ 100gm/Sqm complete all as specified and as directed.

M&L Making the grooves to 'V' section in existing parapet walls/columns over RCC roofs, cleaning out and tacked the polymeric membrane in to the grooves and sealed solidly with a hot mixture of bitumen and clean dry sand in the ratio of 1:1 by weight etc complete all as specified and directed.

Dismantling mangalore pattern roofing tiles single layer including ridge tiles laid, bedded in cement mortar etc including removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

Dismantling battens for tiles any size exceeding 15cm in spacing complete all as specified and as directed.

Dismantling timber Scantling framed work in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and as directed.

Dismantling timber Scantling framed work 40 sqcm and over in section, in any position complete all as specified and as directed.

S&F Second class hardwood clean sawn timber scantling as in purlins, trusses etc framed work complete all as specified and as directed.

Fixing only second class hardwood clean sawn timber scantling as in purlins, trusses etc framed work complete all as specified and as directed

S&F Pre-painted galvalume aluminium zinc coating galvanised based Corrugaed steel sheet 0.50mm thick, AZ-150 of approved colour sheet having tensile strength of 550 Mpa as roof covering/ cladding to wall fixed with self tapping (SD) screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating galvanised based profiled/plain steel sheet 0.50mm thick, AZ-150 of approved colour sheet having tensile strength of 550 Mpa as ridge, gutters fixed with self tapping (SD) screws complete all as specified and as directed.

M&L Providing PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in bed block, coping, roof kerbs, bands filling in hollow portion of chowkats, etc including necessary form work complete all as specified and as directed

S&F Rolled mild steel sections of frame work as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates confirming to Fe 410-W (Gde E-250) quality “A” complete all as specified and as directed.

S&F Plates (plain or chequered )channels, square cut or notched(ordinary and counter sunk)forming holes, without anyattachment etc.Roof strusses (framed) and connecting plates, etc., including necessary precautionary measures as in supports etc., complete all as specified and as directed.

S&F Hand rails, half rounded or other stock section or core for wooden hand rail straight portion, drilled and counter sunk for balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling or riveting etc and similar work confirming to Fe-410-0 of Fe-310-0 of Gde E-165 complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness including cover fillets etc including removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

S & F E Grid suspended false ceiling grid system of size 600 x 600mm with main runner 39x29.7x0.60mm cross tee 29x24.7x0.60mm and wall angle 22.2x22.2x0.50mm ceiling suspended with 2 to 2.5 mm dia GI wire hanger fixed to purlin / truss etc complete (Main runner, cross tee, wall angle of MS galvanised with PPCGS) over the grid providing 4mm thick HPSC pre primed self designer texture non asbestos fibre cement building board fixed to frames etc complete all as specified and and as directed.

M&L Providing RCC (1:1.5:3) type A1 (using 20 mm graded stone aggregate) as in beams, cantilevers bressummers lintels over 1.5 m span,etc complete all as specified and directed.

M&L Providing precast RCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain face and set in CM(1:4) complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunhings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams etc as in rough finished flat surfaces of concrete complete all as directed.

M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips,complete all as specified and directed.

All as per Item No.25 above,but 5mm dia and over upto and including 10mm dia as in stirrups , spacers and binders etc., including all cutting bending, binding, cranking placing & binding with MS wire (annealed) not less than 0.90mm dia complete.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles including removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

M&L Brick work with sub class 'B' bricks of old size, straight or curved on plan exceeding 6.0 metre mean radius built in CM (1:6) complete all as specified and as directed.

M&L Walling of squared rubble masonry regular coursed, Secunderabad and Bangalore types, well bonded, bedded and solidly hearted, built in CM (1:6) complete all as specified and as directed.

All as per item No.29 above but except stones complete all as specified and directed. Note- Serviceable stones obtained vide demolition item above shall be reused after removing mortar and cleaning with water complete all as specifed and directed.

Taking down cement plaster of any description and thickness on brick walls including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed

M&L Rendering 15 mm thick CM (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L Rendering 15 mm thick CM (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L Rendering 5 mm thick CM (1:3) on concrete surfaces such as ceiling or soffits of chhajas etc; finished even and smooth without using extra cement complete all as specified and as directed.

M & L Preparing newly plasterd wall surfaces of walls applying two coats of oil bound distemper (oil emulsion) over a coat of primer over and including a coat of 3mm thick birla care wall putty in two layers complete all as specified and as directed.

M&L Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

M&L Complete removal of existing treatment on wall surfaces and applying two coats of oil bound distemper (oil emulsion) over a coat of primer over and including a coat of 3mm thick birla care wall putty in two layers complete all as specified and as directed.

M & L Preparing the old plastered or unplastered decorated surfaces of walls and applying two coats of white wash complete all as specified and as directed.

M & L Preparing newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and as directed.

M & L Preparing old plastered ceiling surfaces and applying two coats of white wash complete all as specified and as directed.

M&L Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and as directed.

M & L Preparing old decorative surfaces of walls, by washing, rubbing down, stopping and applying two coats of cement base paint of any colour complete all as specified and as directed.

Demolition of PCC of any description and in any position not otherwise specifically provided for(un-reinforcement) including removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

M&L 75 mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection laid in alternative bays finished even and smooth without using extra cement including making 10 mm wide grooves to full depth at 3 m interval and at every change of direction and filling the grooves with mixture of bitumen and sand mixed in the ratio of 1:3 by weight and top 10 mm depth sealed with sealing compound grade ‘A’ complete all as complete all as specified and as directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar including removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store including removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

M&L Non skid coloured ceramic tiles of size exceeding .0.06 square metre but not exceeding 0.11 square metre of 7 to 8mm thick set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including screed bed of 15 mm thick in CM (1:6) complete all as specified and as directed.

M&L Glazed ceramic coloured wall tiles of approved colour of size 350x 250x 7/ 450x300x7 mm thick on vertical surfaces as in dado/wall set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 10 mm thick backing coat of CM (1:4) complete all as specified and as directed.

M&L Machine cut kota stone flooring 20-25mm thick as in flooring set, and jointed with grey cement slurry mixed with pigment to match the shade of the slab inclduing rubbing and polishing over and including 15 mm thick CM (1:6) screed bed complete all as specified and as directed.

M&L Machine cut kota stone 20-25mm thick as in skirting / dado set, jointed with grey cement slurry mixed with pigment to match the shade of the slab inclduing rubbing and polishing over 10 mm thick CM (1:4) backing coat complete all as specified and as directed.

M&L 25 mm thick granite tiles (of any size) machine cut, jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone duly grinding and polishing laid over and including 15mm thick screed bed of CM (1:4) as in steps, jambs, pillars, window cills, cooking platforms and like complete all as specified and as directed

Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified.

M & L Preparation of new or previously untreted steel or iron surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) of size exceeding 1.5 sqm and not exc 4.00 sqm each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) of size not exceeding 1.5 sqm each complete all as specified and as directed.

S&F Steel windows (fly proof and glazed shutter) made with galvanised steel colour coated/ powder coated ( Base steel as per IS 513 'D', galvanised as per IS 277 with zinc of 120gm/sqm) with total coating thickness of 0.60mm. ( outside for glazing and inside gauged shutter) Sections for frame should be of 72mmx55mm, section for mullian should be 72mm x 50mm section for shutter frame should be 47mmx 20mm,and section for fixing glass bead should be 12mm x 12mm and section for fly mesh shutter frame should be 40mm x 20mm mesh fixing should be of 18mm x 0.6mm. Stainless steel wire mesh of 0.45mm dia and ave width of aperture 1.4mm shall be used for fly proofing . 4mm thick plain sheet glass to be used for glazing of glazed shutters complete all as specified and as directed.

S & F PVC solid ventilator frame size 55 X 47mm with wall thickness of 5mm made out of extruded 5mm PVC sheet, mitre cut at two comers and jointed with 2 Nos of 150mm long brackets of 15 x 15mm MS square tube the two vatted profiles are to be reinforced with 19 x 19mm MS squre tube the 50% of bottom portion is fixed with 4mm pin headed glass and balance 50% of top portion is fixed with 4mm thick pin headed glass lowers and cover with 0.36mm dia stainless steel wire mesh at top portion including necessary PVC beading with screws and 3 Nos 12mm dia MS guard, bars fixed in ventilator frame including two coats of synthetic enamel paint over a coat of red oxide primer to MS guard bars etc complete all as specified and as directed. Make: SINTEX/ RAJSHRI/ NANDI as approved by GE.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 50x100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). → Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra , complete all as specified and as directed.

S& F30 mm thick Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) complete all as specified and as directed.

S&F 100 mm size butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type C-21 complete all as specified and as directed

S&F 150 mm length aluminium anodised barrel tower bolt of extruded section with bright bolt complete all as specified and as directed.

S & F 150 mm long aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S&F 125 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed.

M&L Cutting holes in brick wall built in cement mortor for inserting hold fast and making good the disturbed portion in CM (1:3) depth of embeded portion exc half brick & n.exc one brick complete all as specified and directed.

S & F 35 mm thick factory made second class hardwood, plain framed panelled shutters (any number of panel) with panels of timber flat on both sides(feather edged) or of veneered particle board medium density wood particle board with commercial veneering on both faces. complete all as directed and specified.

S & F 35 mm 2nd class hard wood factory made glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I section 8 clause 8.24(a) etc completed all as specified and directed.

S & F Mild steel sliding bolt 300 mm long plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fix complete all as specified and as directed.

M & L Preparation of newly wood or wood based surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of prink primer etc completed all as specified and directed.

M&L Rendering 15 mm thick CM (1:3) duly mixed with water proofing compound as per manufacturer's instructions as in sunken floors and finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound shall be measured and paid separately under relevant items in this schedule.

M&L Application of one coat of water based bitumen emulsion primer at the rate of 0.3 litre per sqm after cleaning of the surfaces thoroughly from dust, dirt and projections and applying water proofing treatment with APP polymeric membrane of weight 3 Kg per sqm and minimum 3mm thick reinforced with polyster non oven fabric (weight not less than 150 gm/sqm) over that a coat of blown bitumen of 85 / 25 at the rate of 1.2 kilogram per sqm over that providing a sand layer of 25mm thick thick in sunken floors complete all as specified and as directed.

M&L PCC (1:5:10) type E2 (using 40 mm graded stone aggregates) as inr filling in sunken floor and mass concrete complete all as specified and as directed.

Dismantling / taking down PVC/ Cast iron soil /waste pipes 100 mm / 75mm bore including all fitting like bends etc complete all as specified and directed

S&F PVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent and cement concrete type B1 (1:2:4) & including removing old trap and fixing of stainless steel grating in ground shape etc complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipe single socketed (ISI Marked) any length with rubber ring joints , complete fittings etc fixed to walls fixed with MS clamps 8 mm dia with two nuts wall nails etc complete all as specifed and directed.

S&F 110 mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to walls fixed with MS clamps 8 mm dia with two nuts wall nails etc complete all as specifed and directed.

S&F 75 mm bore PVC (SWR) bends any radius dimnishing pieces or tapers with access doors etc, complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) bends any radius dimnishing pieces or tapers with access doors etc, complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) branch piece, single (single Y ) equal or unequal with access doors etc, complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) junction single (single T ) equal or unequal with access doors etc, complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) vent cowl etc, complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) vent cowl etc, complete all as specified and as directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 25mm complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 40mm complete all as specified and directed.

Cutting and grooving of wall for fixing of CPVC pipe lines and after fixing of CPVC pipe line and making good of all cutting surfaces etc complete all as specified and directed.

S&F CPVC pipes, SDR 11, 20 mm outer dia of pressure rating 6kgf/sqcm conforming to IS-15778 with all CPVC fittings with such as brass elbow ,Tee, bends, unions ,sockets , male and femaleThreaded Adoptor and end pieces etc to receive fittings and fixed with solvents fixed to walls / ceiling with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure etc complete all as specified and as directed.

S & F 15 mm dia GI tubes (medium grade) ISI marked, galvanised with all fittings fixed to walls and ceilings or laid in floors complete all as specified and directed.

S & F 20 mm dia GI tubes (medium grade) ISI marked, galvanised with all fittings fixed to walls and ceilings or laid in floors complete all as specified and directed.

S & F 25 mm dia GI tubes (medium grade) ISI marked, galvanised with all fittings fixed to walls and ceilings or laid in floors complete all as specified and directed.

S & F 40 mm dia GI tubes (medium grade) ISI marked, galvanised with all fittings fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F in repair 25 mm dia gun metal globe or gate valves with iron wheel head , screwed both ends for iron pipe & fixed complete all as specified and directed.

S&F 20mm dia gun meteal,globe or gate valves, with iron wheel head screwed both ends for iron pipe and fixed complete all as directed.

S&F in repairs 2000 litres capacity rotational moulded polyethylene water storage tank of triple layer type(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed

S&F in repairs vitreous china water closet 'Orissa' pattern of size 580mm X 440mm, white with integral foot rest (excluding flushing cistern), but including PVC flush pipe and provision of lime concrete bedding complete all as specified and as directed.

S&F in repair wash down water closet (pedestal pattern) white and including plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device (excluding flushing cistern ) etc complete all as specified and directed.

S&F PVC Low level flushing cistern 10 ltr capacity, including waste pipe, down take pipe, pair of CI brackets and all accessories complete all as specified and as directed.

S&F in repairs vitreous China counter top wash basin of size 600 x 450 x 190 mm with 32mm dia brass chromium plated waste coupling and cast iron brackets complete all as specified and as directed. MAKE: CAT No Jaquar Code- QNS-WHT-7601AT No 10051 or equivalent model in HINDWARE PARRYWARE/CERA as approved

S&F in repairs Pillar taps, fancy type, chromium plated, screwed down, high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15 mm bore complete all as specified and as directed.

S&F in repairs 125 mm dia brass chromium plated shower rose with swivel joints with stainless steel arm duly ISI marked complete all as specified and as directed

S&F in repairs of PVC connection of 15mm size with PTMT nuts of length 450mm complete all as specified and as directed

S&F in repairs of PVC connection of 15mm size with PTMT nuts of length 600 mm complete all as specified and as directed

S&F in repairs vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screw, pointing around urinal back in cement with grating and union for discharge pipe complete all as specified and as directed

M&L Cutting of granite slab for fixing of under counter wash basin including rounded and grinding the stone with necessary arrangments complete all as specified and as directed.

S & F in repairs Towel rail 600 mm long of brass chromium plated fixed with and including CP brass screws and wooden/plastic cleats. (Minimum weight 190 gms) complete all as specified and as directed.

S&F in repairs soap dish brass complete all as specified and as directed MAKE: CAT No F880011 of HINDWARE or equivalent model in JAQUAR/ PARRYWARE/CERA as approved by GE

S&F in repairs 15mm dia brass chromium plated Two way Bib tap with wall flange type, fancy type, and high pressure, with flange screwed, and screwed both ends for iron pipe or for unions complete all as specified and as directed. MAKE: CAT No F200004FT of HINDWARE or equivalent model in JAQUAR/ PARRYWARE/CERA as approved

S&F in repairs CP bib tap 15mm bore fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs CP angle cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fixed in repairs of 6mm thick frame less beveled rectangular wall mount plain mirror of any size and fixing of necessary Stainless steel finish solid mirror stud (12mmX19mmX2.5cm) complete all as specified and as directed Make: Saint-gobain/ Modi guard or equivalent model as approved by GE

S&F Stainless steel curtain rod of 25 mm bore fancy type complete all as specified and as directed

S&F in repairs for stainless steel curtain rod brackets (decorative type) suitable for curtain rod of 25 mm dia, complete all as specified and as directed.

M&L LLDPE septic tank of conventional type designed to carry sewage and sulage water, excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc., complete for 30 users capacity complete all as specified and as directed by Engineer-in-Charge.

M&L Soakage well of size 3.6 m dia x 4.5 m effective depth with excavation, in all type of soil, foundation in PCC (1:3:6), walls of honey combed masonry with top ring of M 25 concrete including intercepting chamber and screen chamber made of brick masonry in CM (1:4), RCC cover slabs in M 25/ SFRC cover, interconnecting pipes of RCC/ DWC, filled with brick bats, etc., complete all as per drg No. TD/ST/748 Sheet No. 1/1 dated 22 Jan 2011 as specified and directed by Engr-in-charge.

M&L DCWPE (SN8) 180 (OD)/163(ID) mm diameter pipes of length 0.70 m to 1.65m laid on 150mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of brick masonry/RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional complete all as directed by Eng-in-charge.

Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes complete all as specified and as directed.

Taking down old unservicieble existing submain wiring of any size and type complete all as specified and as directed.

Taking down old unservicieble existing DB's any size and type complete all as specified and as directed.

M&L Point wiring of any length from DB complete with stranded copper conductor cables in concealed non-metallic PVC conduit 1.5 Sqmm (nominal area) PVC insulated unsheathed cable up to 1100 V grade FRLSH conforming to IS - 694 multistranded drawn including conduit with new sunk type pressed steel terminal boxes suitable for MODULAR switches including fixing/grouting sunken/ surface as per site requirement covered with suitable modular white cover plate for suitable size for mounting of MODULAR switches, regulators and drawing continuous earth wire with one run of 1.5 Sqmm (nominal area) PVC insulated unsheathed cable up to 1100 V grade FRLSH conforming to IS - 694 multistranded copper conductor as earth wire and connecting to common earth dolly for one light/ Bell point controlled by one, one way switch 5 amps, SP and making good the disturbed wall surfaces to match with the existing surfaces complete all as specified and as directed. Note - Cutting chases,making good, painting, will be measured and paid seperately.

All as per Item No.119 above,but one Ceiling Fan / exhaust fan point controlled by one, one way switch and regulator

All as per Item No.119 above,but one 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board .

All as per Item No.119 above,but one 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

All as per Item No.119 above,but using 2.5 Sqmm single core FRLSH copper conductor cable of multistranded PVC insulated unsheathed 1100 Volts grade for 3 Pin 15 Amps switch socket combination point on independent board including running of 2.5 Sq mm FRLSH copper conductor PVC insulated cable as earth continuity conductor. Note - Cutting chases,making good, painting, will be measured and paid seperately

S & F Switch Piano flush button single pole one way 5 Amp, 240 volt complete all as specified and as directed.

S & F in repair/replacement of Switch Socket outlet 3 Pin, 5 Amp flush type, 240 volts, complete all as specified and as directed.

S & F Switch Socket Combination 5 in 1, 3 pin, 5 and 15 Amp flush type universal, 240 volts, complete all as specified and as directed.

S & F Switch Socket Combination 2 in 1, 3 pin, 6 Amp flush type universal, 240 volts, complete all as specified and as directed.

Supply and fix electronic ceiling fan regulator 5 stepped type heavy duty suitable to work on 230 volts complete all as specified and as directed.

S&F in replacement wall mounted LED batten with extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver 1 x 10w, 230 volts, bipin holders, DIFFUSED TYPE connector block internally prewired etc with 2 Nos PVC round blocks for mounting arrangements including all accessories with new 3 core multi stranded copper conductor of size 23/0.193 from ceiling rose to fitting and including LED Tube 10W complete all as specified and as directed.

S&F in replacement wall mounted LED batten with extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver 1 x 20w, 230 volts, bipin holders, DIFFUSED TYPE connector block internally prewired etc with 2 Nos PVC round blocks for mounting arrangements including all accessories with new 3 core multi stranded copper conductor of size 23/0.193 from ceiling rose to fitting and including LED Tube 20W complete all as specified and as directed.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed.

S&F in replacement ceiling rose three terminal surface bakelite type AC 50 Hz 230 volts of size 65 x 50 mm complete all as specified and as directed.

S&F in replacement sheet metal enclosure MCB DB SPN 8 way with 200 amps rated bus bar 240 volts double door with magnetic locking system complete all as specified and as directed.

S & F sheet metal enclosure MCB DB TPN 4 way with 200 amps rated bus bar 415 volts double door with magnetic locking system complete all as specified .

S&F MCB, SP 6-32 Amps, 240 volts of rupturing capacity 10 KA, 'C' series complete all as specified and as directed.

S&F MCB, SP 40 Amps, 240 volts of rupturing capacity 10 KA, 'C' series complete all as specified and as directed.

S & F MCB SPN 32 Amps 240 volts,'C' series complete all as specified and as directed.

S & F MCB TPN 40-100 Amps 240 volts complete all as specified and as directed.

M & L Submain wiring with two single core 4 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through and including rigid PVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of 4 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly complete including removing the existing unserviceable sub main wiring and making good the disturbed surface to match with the existing all as specified. Note:- 1. Three runs of 4 sqmm cable and one run of conduit shall be measured and paid as one unit length. 2. Cutting chases,making good, painting, will be measured and paid seperately

M&L Earthing with galvanized mild steel earth plate electrode 60 centimetre x 60 centimetre x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 metres below ground level, the top edge of the earth plate at a depth of not less than 1.5 metres below ground level connected to galvanized iron earth wire of 4 mm dia by means of bolts, nuts and washers made out of GI / steel earth wire protected by GI light grade pipe 15 mm bore, 20mm dia light grade galvanised iron pipe with funnel wire mesh for watering and connecting to main switch board / control board all s shown in electrical plate of SSR Pt - I connected to earthing test point and including testing on completion complete all as specified and as directed. Note: The unit rate shall also include for excavation, earth work in hard/dense soil, plain cement concrete 1:3:6 type C1 by using 20 mm graded aggregate in pit, 50 mm thick reinforced cement concrete 1:2:4 type B1 using 20 mm graded aggregate cover duly reinforced with 8 mm dia TMT bars @ 100mm centre to centre both ways, galvanised iron funnel with watering pipe, wire mesh, etc

Disconnecting and removing ceiling/exhaust fan of any capactiy any height from electrical connection bringing down, dismantling, cleaning internally and externally thoroughly examine replacement of split pins, cotter pins and check nuts etc overhauling, lubricating with approved lubricants, reassembling, including replacement of wornout/defective parts, refixing in original position including minor repairs for the smooth functioning and provision of new flexible wire of size 23/0.0076 multistranded copper conductor cable from ceiling rose to fan Note :- (1) Necessary repairs/ replacement of unserviceable parts shall be measured and paid seperately. (2) Labour element for replacing of u/s parts deemed to be included in rate quoted.

M&L Rewinding of the ceiling/exhaust fan complete with equivalent new super enamelled copper wire of existing gauge and weight as per manufacturer's design and instructions including varnishing of ceiling fan of any make and any sweep complete all as specified and directed including taking out burnt copper wire. Note: old winding material is property of the contractor

S&F in repairs of Ball bearing/Brass bush of Ceiling Fan/Exhaust Fan complete all as specified and as directed.

S&F in repairs of Capacitor Ceiling Fan/Exhaust Fan complete all as specified and as directed.

M&L Painting of ceiling fans 48”/56” size complete at site, with super synthetic enamel paint by spraying incl filling cavities with filler, one coat after cleaning all dust etc complete,all as specified and as directed by Engr-in-Charge.

Taking down the geysers of capacity 25/50 Ltrs from its mounting position by removing all water and electric connections and de-assembling the geyser and carrying out the following works complete all as specified and directed. (a) Descaling, cleaning the inner tank thoroughly and there should not be any bad taste of water. (b) Examining the water tightness of storage tank after cleaning. (c) Examining the physical condition of thermostat, base assembly fusible plug and outer tank for its serviceability. (d) Inspection of pilot lamps. (e) Reassembling the geyser parts and testing including checking all electrical system (ensuring there is no current leakage) and also conducting hydraulic testing. (f) Re-fixing the Geyser and making electric connections, inlet and outlet water connections and testing and checking of all water inlet, outlet valves connected with geysers. Note : Defective /worn outparts if required shall be measured and paid separetely under relevant items in this schedule.

S&F Rubber PVC connection of 2/3 feet complete all as specified and directed.

S&F MS base plate cup any type with screws of suitable size as per requirement complete all as specified and directed.

S&F Heating element of the 2 KW rating as required at site including rubber washers of any make and type complete as per sample, complete all as specified and directed.

S&F Steel inner tank of 25/50 litre capacity geyser tank by made out of copper sheets appropriate thickness complete all as specified and directed.

S&F Thermostat for the geysers of the 25/50 Liters capacities complete all as specified and directed.

S&F in repairs Air Release Valve of existing size complete all as specified and directed.

S&F in repairs Indication lamp of Existing Size/Model (Set of Two) Red & Green complete all as specified and directed.

S&F in repairs Flexible cable of size 3 core2.5 sqmm, PVC insulated PVC sheathed with stranded copper conductor,1100 Volt grade complete all as specified and directed.

S&F in repairs Metallic louvers mounted suitable for exhaust fan of 300 to 450 mm on wall complete all as specified and directed.

M & L Cutting chases, pining to making good to facing where ever required and pointing in CM (1:3) to ends or edges of endings, steps, cills etc and cutting chases for concealed wiring making good and cutting not exceeding10 cm grith complete all as specified and directed.

M/S RADHIKA ENTERPRISES (BID ID -3342911)

M/s GM Constructions (BID ID -3343366)

BHEEMRAO PATIL CONTRACTOR (BID ID -3335056)

Venkat Ramaiah (BID ID -3335555)

VACON INFRASTRUCTURES (BID ID -3334420)

PARDEEP AND CO (BID ID -3335456)