WBPWD/AE/BNGSD/eNIT-31/25-26

Stripping off worn out plaster and raking out joints of walls, celings etc.up to any height and in any floor including removing rubbish within a lead of 75m as directed. Ground Floor Front Side

Brick work with 1st class bricks in cement mortar (1:4) (a) In foundation and plinth

Plaster(to wall, floor, ceiling etc.)with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (a) 20 mm thick plaster

(b) 15 mm thick plaster

(ii) With 1:4 cement mortar (c) 10 mm thick plaster

Neat cement punning about 1.5mm thick in wall, dado,window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m

Dismantling artificial stone flooring upto 50mm.Thick by carefully chiselling with out damaging the base and removing rubbish as directed with in a lead of 75 m. a) In ground floor including roof.

Dismantling all types of plain cement concrete works, stacking service able materials at site and removing rubbish as directed with in al ead of 75 m. In ground floor including roof.

(A)Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturationwith water, ramming complete including the cost of supply of sand. (payment to bemade onmeasurement of finished quantity

Brick soling with picked jhama bricks including preparation of bedas necessary with brick joints properly filled in and packed with powdered earth and including necessary cushion of similarmaterial below the soling (and in between layers when more than one layer is used) completes as per direction. (a) Single brick flat soling (thickness 75 mm.)

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20mm nominal size) excluding shuttering and reinforcement ,if any, in ground floor as per relevant IS codes. a) Pakur Variety

Supplying and laying true to line and level Anti-Skid, Full Body,Homogeneous & Granular finish Vitrified Tiles conforming toIS:15622-2006& IS4457-2007 and testings hall be made in accordance with IS:13630 [Non-modularsizes for tiles with Skid resistance>0.5,Mohr's hardness >5.0, Staining resistance: Clas 1,WaterAbsorption:E<0.5%],MOR>35N/sq.mm in Internal area of building e.g.ToiletBlock, Passage,Corridor,Accessible Open Terrace etc.set in 20mm sand cement mortar (1:4) and 2mm thick cement slurry at back side of tiles using cement @2.91Kg./Sqmorusing Polymerised Adhesive (6mm thick layer applied directly over finished artificial stone floor/Mosaicetc without any backing course) laid after applications lurryusing 1.75Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/epoxygrout materials of approved make as directed and removal of wax coating of to psurface of tiles with warm water and polishing the tile susings of tanddry cloth upt omirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor). a) In Ground Floor :Sizes-300mm x 300mm x 10mm with breaking strength> 1200 N

Applying Acrylic Emulsion Paint of approved make and brand on walls and celling including and papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : ii) Laxury Quality

ApplyingExteriorgradeAcrylicprimerofapprovedqualityandbrand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsionpaint includingscrapingandpreparingthesurfacethroughly, completeaspermanufacturer'sspecificationandasperdirectionofthe EIC. In Ground Floor: (a) One Coat

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as permanufacturer's specification and as per direction of Engineer-in Charge to be applied over acrylic primer as required.The rate includes cost ofmaterial, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) b) Premium 100% Acrylic Emulsion

Supplying fitting and fixing in position approved P.V.C.door frame (Matt finish) made of extruded P.V.C.multi chamber hollow section having dimensions 60mm x 50 mmx2 mm (+/-0.2mm),horizontal section will be joined with vertical section by galvanised steel screws after inserting two number steel brackets as reinforcement making suitable space for placing hinges,one steel tube 40mm x 20mmx1.20mm will be inserted on one full vertical side of the frame (hingeside) as reinforcement, the framewill thenbe fixed in theopeningwith the help of P.V.C. expandable fastner/wooden gutties and galvanised steel screws including cost of all materials and labour,hirecharges of tool sand appliances,carriage of all materials, taxes and all other incidental charges complete.

PVC Door Shutter-30 mm thick Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm x30 mm section with 2.0 mm (+/-0.2 mm) wall thickness.Horizontal & vertical section shall be fixed to each other by self tapping screws and 1 solid polymeric or M.S. galvanised tubular 'L' shaped bracket 100mm x 200mm in each corner of the shutter frame for placing hinges. Polymer based multicavity hollow section of 120 mm x30mm with 2.0 mm (+/- 0.2 mm) wall thickness will be fitted in the middle, reinforced by solid polymer bar of 200 mm long at both ends and screws from both sides as lock rail. The section frame will then be fitted in by PVC panels of size 100 mmx25 mm with wall thickness of 1.2 mm (+/- 0.2 mm) and 2 nos. of 6 mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing of hinges / hasp bolt / tower bolt / door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliancesi/c carriage of all materials taxes and all other incidental charges complete.

Supplying, fitting & fixing UPVCpipes A-Type and fittings conforming to IS:13592-1992with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil throughmasonry concrete structures etc if necessary and mending good damage sincludin gjoining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. A) UPVC Pipes: (ii) 110 mm dia

(C) Bend (ii) 110 mm dia

(D) Shoe (ii) 110 mm dia

Dismantling Orissa pattern W.C. including taking out of base concrete, if necessary, complete.

Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer (b) 1000 litre capacity

Labour for hoisting plastic water storage tank (i) Upto 1500 litre capacity.

Labour for punching hole in plastic water storage tank upto 50 mm dia

Supplying, fitting and fixing PVC pipes for under ground work of approved make of Schedule 80 (mediumduty) conforming to ASTMD 1785 and threaded to match with GI Pipes as per IS:1239 (Part-I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted includingcost of allmaterials ,jointingmaterials, cutting pipes, making threads, cutting trenches upto 1.5metre below surface in all sorts of soil and refilling the same as directed complete in all respect.(Payment will bemade on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials. PVC Pipes 15 mm

Supplying, fitting and fixing bib cock or stop cock (e) PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent) 15 mm

Stop Cock

Supplying, fitting and fixing pillar cock of approved make b) PTMT Pillar Cock - 15 mm. (Prayag or equivalent)

Wash basin vitreous china of approved make (without fittings) supplied ,fitted and fixed in position on 75mm X 75mm X 75mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets. (iii) 630 mm X 450 mm size

Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing). (ii) 530 mm X 410 mm

Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. 600 mm long

Supplying, fitting and fixing approved brand 32mm dia.P.V.C.waste pipe, with PVC coupling at one end fitted with necessary clamps. 600 mm long

Supplying, fitting and fixing soap holder. (a) PTMT (Prayag or equivalent)

Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red as per I.S. 3438 / 1965 together with brass C.P. hinges. (ii) 600 mm X 450 mm

Supplying, fitting and fixing Squating plate with integral flushing in white vitreous chinaware of approved make in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid seperately). (i) 450 mm X 350 mm

Supplying, fitting and fixing towel rail with two brackets. (a) C.P. over brass (ii) 25 mm dia. and 600 mm long

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 xx) 125/110 P Trap with W.C. Ring

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (A) (i) Single Socketed 3 Meter Lengt

Sub Total

Please Enable Macros to View BoQ information