SPL REPAIR TO QTR NO O-84 IN CENTRAL ZONE UNDER GE (NORTH) BINNAGURI

Amount

Demolition of existing roof treatment complete of any description and including taking down existing tarfelt including tiles, lime/ cement concrete and screed bed complete from roof surfaces including parapets and lowering and removing the same to a distance exc. 50m and n. exc.100m including roughening of old concrete surface of roof, cleaning the surface by wire brushing to remove all loose dust etc complete all as specified and as directed.

Material and labour for rendering 10 mm thick screed bed on roof slab concrete surfaces , in cement and sand mortar 1:4 using water liquid water proofing compound @ 200 ml per bag of cement or as per manufacturer's instructions (WPC shall be measured and paid separately) complete all as specified and as directed.

M&L for providing and applying single component acrylic polymer modified, fiber reinforced waterproof coating in 4 coats of application (a) applying primer coat with Primer @ 0.3 kg /sqm (b) over priming coat applying as specified below or manufacturer instructions with fiber reinforcement a width of approx 1m @ 0.75kg/sqm on the flat or vertical surfaces over parapet wall and ensure that there are no bubbles of creases. Overlapping of the fiber is a minimum of 50mm and allow this coat to dry for a period of 2-6 hrs depending on the atmospheric condition. (c) Applying second coat @0.75Kg/sqm (d) Applying final coat of @ 0.08kg/sqm after 2nd coat has dried properly. (Note : Water Proofing treatment shall be carried out by authorised applicator approved by the manufacturer.)

Dismantling water tanks and removing to store of capacity exc 500 & n.exc 1000 ltrs including ball/float valve etc complete all as specified and as directed.

Supply and fix 1000 ltr capacity of rotational moulded poly-ethylene triple layer water storage tanks ( cylindrical vertical with closed top) hoisted and including connecting up pipes securing access covers etc.,complete all as specified and as directed.

S & F 500 ltrs rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) including connecting up pipes securing access covers etc complete all as specified and as directed.

Supply and fixed ball valves, high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms) complete screwed for 20 mm bore dia. pipe or brass ferrule complete all as specified and as directed

Supply and fix in repairs 20mm dia Gunmetal globe or gate valves, with iron wheel head, screwed both ends for 20 mm bore iron pipe and fixed complete all as specified.

Roughening surfaces of old concrete floor/ vertical surface by picking, sweeping clean and washing down with water to remove dust etc.and prepare the surface to receive tiles including applying 3Kg/Sqm cement slurry complete all as specified and directed.

Material and labour for Vitrified Ceramic joint free tiles 8-9 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.72 sqm but n. exc 1.00 sqm , in floors over and including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed.Note:- Design and pattern shall be approved by Engr-in-charge /GE at the time of execution of work.

Material and labour for Vitrified Ceramic joint free tiles 8-9 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.72 sqm but n. exc 1.00 sqm, as in vertical surfaces such as skirting / dado over and including 10 mm thick backing coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed.

Material and labour for Vitrified Ceramic joint free tiles 8-9 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 sqm but n. exc 0.36 sqm , in floors over and including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed.Note:- Design and pattern shall be approved by Engr-in-charge /GE at the time of execution of work.

Material and labour for Vitrified Ceramic joint free tiles 8-9 mm thick (square/ rectangular) polished, area of each tiles exceeding .18 sqm but n. exc 0.36 sqm, as in vertical surfaces such as skirting / dado over and including 10 mm thick backing coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), in floors, aprons etc .laid dry or laid dry and pointed including removing of demolished material from work site at any distance outside MD land complete all as specified and directed complete all as specified.

Material and labour for Non Skid ceramic coloured tiles (1st quality) 7 to 8mm thick ( square/ rectangular) area of each tile exc 0.18 sqm but not exc 0.36 sqm, as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor over and including 15 mm thick screeding in CM 1:6 complete all as specified.Note:- Design and pattern shall be approved by Engr-in-charge /GE at the time of execution of work.

Material and labour for glazed ceramic coloured / digital printed/Elevation tiles of size 300 x 450 mm x 7 mm thick ) as in vertical surfaces of walls such as skirting/dado / riser to steps etc conforming to relevant IS set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed / backing layer of 10mm thick in cement mortar (1:4) complete all as specified and as directed

M&L for Providing and laying of 300x300 mm & 10mm thick Anti-Skid pavement tile Endura tile of "H & R Johnson India" or equivalent in pavit or NITCO in approved color & Shade or techno commercially equivalent make as listed in list of makes and in anti skid finish set and jointed in neat cement slurry and pointed in white cement & pigment to match over and including 20 mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer- in - Charge .(Note: Design/pattern shall be as approved by GE at the time of execution)

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.bedded and pointed in any mortar including removing of demolished material from work site complete all as specified and directed.

Material and labour 15-18 mm thick Granite work ( table rubbed and polished) in steps , jambs, pillars, window cills, cooking platforms and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screeding in CM 1:4 including full rounding the exposed surfaces and provn of holes for gas pipe etc, complete all as specified.Note:- Granite colour shall be approved by Engr-in-charge /GE at the time of execution of work.

Taking up or down GI tubing15mm bore pipe and connection including cleaning for refixing or removal from site as directed.

Taking up or down GI tubing 20mm bore and connections including cleaning for refixing or removal to store.

Supplying, laying, jointing and testing 15 mm nominal bore Steel water tubes, 'medium grade' ,galvanised , with all fittings ; fixed to walls and ceilings or laid in floors complete all as specified.

Refixing old steel tubing and connections in new or old position ( walls, ceiling , floors, etc.)15 mm nominal bore dia, including new fittings complete all as specified ( Note:- Refixing shall including cleaning down existing serviceable pipes and fittings. )

Supplying , laying, jointing and testing 20 mm nominal bore Steel water tubes, 'medium grade' ,galvanised , with all fittings ; fixed to walls and ceilings or laid in floors complete all as specified.

Refixing old steel tubing and connections in new or old position ( walls, ceiling , floors, etc.) 20 mm nominal bore dia, including new fittings complete all as specified ( Note:- Refixing shall including cleaning down existing serviceable pipes and fittings. )

Taking down cement plaster on brick work of any description including racking out joints and cleaning dust etc including removing rubbish material complete all as specified.

M&L for applying average 15 mm thick plaster in two coats (10+5 mm) with ready-mix pre-packed proportioned dry mix mortar, blended with PP fibres, mixed with liquid water proofing compound on top layer @ 200 ml per bag of cement or manufacturers instructions on fair faces of brick wall or concrete surfaces on external surfaces including transporting of material, mixing, curing, scaffolding etc and finished the surface even and fair w/o using extra count complete all as specified and as directed. Note Liquid water proofing compound will be measured and paid separately.

M&L for rendering 15mm thick in CM 1:6 on brick or concrete surface finished even and fair without using extra cement complete all as specified.

M&L for rendering 5mm thick plastering in CM (1:3) on ceiling, soffits of slabs, chajjas, columns and beams etc and finished the plastered surface even and fair without using extra cement. Complete all as specified and as directed

Supply only liquid water proofing compound etc complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of walls by applying one coat of wall care white putty and sand papering surfaces to achieve smooth surfaces and applying acrylic based distemper two coats, white or any tinted over a coat of alkaline resistant primer including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified . Note :- Room colour / texture shall be approved by Engr-in-charge /GE at the time of execution of work.

Material and labour for preparation of old decorated distempered surfaces of walls by washing, rubbing down and stopping of distempered and painted surfaces and distempering walls by applying one coat of acrylic based distemper of any tint/shade including wall putty/white cement wherever required to fill the wall cracks/holes complete all as specified and as directed complete all as specified and as directed.

M&L for preparation of new plastered surfaces on wall / ceiling / chajjas and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 Ltre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new/old surfaces as per the manufacturer instruction and all coats including primer to be applied with fully automatic airless spray machine of paint application with flow speed of minimum 1 Ltr per minute having pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and as directed by GE / Engineer-in-Charge.

Material and labour for complete removal of existing treatment for preparation of old decorated treatment on wall / ceiling / chajjas by scrapping with true care wall sander : L-01/H-01 ( having mechanical vacuum mechanism ) having RPM not less than 1500, sanding pad of 80 grit having dia 7"/9" to make the surface free from dust, loose paints etc. or equivalent makes viz Xpress sanding machine having suction vacuum bag or by manual scrapping tools where mechanical removal is not possible and filling cracks, holes etc complete and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/old surfaces as per the manufacturer instruction and all coats including primer to be applied with fully automatic airless spray machine of paint application with flow speed of minimum1 ltr per minute having pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and as directed.

Material and labour of preparation of new plastered or unplastered surfaces of ceilings and applying three coats of white wash including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified .

Material and labour for preparation of old plastered or unplastered surfaces of ceiling by brooming down or steel wire brushing ; scrapping down smoke soot , moulds, moss and efflorescent salts and treating oil and greasy spots and applying two coats of white wash on old decorated surfaces of ceiling including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified and as directed .

M & L for preparation of old treated surface of wall by brooming down or steel wire brushing; scrapping down smoke root, moulds, moss and efflorescent salts and treating oil and greasy spots and applying two coats of white wash on old decorated surfaces of wall including washing floors, cleaning glass, joinery, electrical fittings, wiring etc of drops and splashes complete all as specified and directed.

Demolition Brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles including removing of demolished material from work site complete all as specified.

Material and labour for brickwork with fly ash bricks, old size, having compressive strength not less than 75Kg sqcm, straight or curved on plan exc 6 M mean radius in built in cement and sand mortar 1:6 complete all as specified.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including removing of demolished material from site to distance exc 100 mtr but n.exc 150 mtr, complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specially provided for as in floors,surface channel etc complete all as specified and as directed.

M&L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) in water tank platforms, Flooring etc complete all as specified and as directed.

Material and labour for 75mm thick PCC (1:3:6), type C-2 (using 40 mm graded crushed stone aggregate ) as in plinth protection; pathway / hardstanding etc laid in bays / panels not exc. 2.00 Sqm each including construction joints at suitable interval and each corner and filled with bituminous mastic filling (1 part bitumen & 3 part sand) and finished the surface even and fair without using extra cement complete all as specified.

M&L for 75mm thick PCC 1:4:8 type D-2 as in sub base using 40mm graded mechanically crushed stone aggregate complete all as specified and directed by Engineer-in-Charge.

Material and labour for 80 mm thick coloured rubber moulded machine pressed precast concrete interlocking paver block chemically treated any shape, size and colour confirming to relevant IS of M-40 Grade with grey cement and pigment over and including 40 mm thick sand cushion spread and laid leveled in layers complete all as specified.

Taking down chowkat with shutter exc 1.5 sqm and n. exc. 4.00sqm each including builders hardware complete all as specified and as directed.

Taking down chowkat with shutter n. exc. 1.5sqm each (without taking off shutter from the Frame)including builders hardware complete all as specified and as directed.

Taking down shutters exc 1 sqm and n exc 2 sqm including builders hardware complete all as specified and as directed.

Refixing shutters in same opening of any description of area exc 1 Sqm but n.exc 2 Sqm each complete all as specified and as directed.

M & L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm thick size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary fittings shall be paid separately) , Note :- Wooden finish colour to be approved by GE/ Engineer -in-charge.

S&F of Factory made partly glazed i.e.. upper panel will be wire mesh fitted externally in the clear space & lower panel will be coloured PVC sheet 5mm thick PVC door shutter 30mm thick (style ) consisting of frame made out of M.S tubes for top & bottom , rails , MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for sides and plain colour PVC sheets for botop rail , lock rail & bottom rail on either side & as gap insert for top rail & bottom rail , paneling of plain colour PVC sheet PVC sheet beading , and jointed together with solvent cement , complete all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary fittings shall be paid separately) ,Note :- Wooden finish colour to be approved by GE/ Engineer -in-charge.

M&L for Providing and fixing Factory made single uPVC white colour sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ 0.2mm) . Window profile with hollow section with multi chamber . Frame (88mm x52mm), sliding mesh sash ( 42x75mm ). sliding interlock ( one vertical length in each shutters) (45.5mmx28mm), glazing bead (24.5mmx16mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware . EPDM gasket , 1.2+ 0.2mm thick galvanised steel frame (30mmx 18mm ) 2 nos , sliding sash (30x18mm), sliding mesh sash (26x10mm) profile to be inserted in required profile , frame will be fixed to the wall with 8mm x100mm long fasteners, (Hardware; Touch lock of zinc alloyed (white powder coated), steel roller system Stainless steel wire cloth 0.36mm normal dia of wire and average width of aperture 1.40mm and required accessories.), all as per direction of Engineer-In-Charge.

S&F Powder coated aluminium louvered ventilators of size 600X600mm with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing , anodised aluminium snap beading,screws, anodised aluminium fittings and 5.5mm thick tinted glass fixed in panels with suitable locking arrangements including taking down of old existing steel ventilator and making good disturbed surface of wall complete all as specified and as directed.

S& F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification with Wood free EPS.as per specification and drawing complete as directed.Note :- Wooden finish colour to be approved by GE/ Engineer -in-charge.

M & L for providing & fixing factory made solid PVC cup board frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5 mm thick PVC sheet of density 600Kg/cbm having pat tam width of 50mm and thickness of 10mm. All three frame length reinforced with 19mm x 19mm MS square tube of 19 gauge. mitre cut at two corners and joined with two nos of 150mm long brackets of 15X15mm MS square tube or joint by fusion hit welding. The door frame shall be fixed to the wall thickness using 8Xthroughout the frame and metre cut at two corners and jointed with 2 nos of 150mm long brackets of 15mm x 15mm MS square tubes.The door frame shall be fixed to the wall using 8/100mm long MS screws through the frame by using PVC fasteners. A minimum 4 nos of screws to be provided for each vertical member and minimum 2 nos of screws to be provided to the horizontal member etc.complete all as specified and dir by Engineer in charge. Note :- Wooden finish colour to be approved by GE/ Engineer -in-charge.

M & L for providing & fixing factory made solid WPC (Natural Wood) Prelam Plain Colour both side 24 mm thick all as specified. Note :- Wooden finish colour to be approved by GE/ Engineer -in-charge. Complete all as specified and as directed

M&L for providing and fixing factory made WPC (Natural Wood) Prelam Plain Colour both side shelf/partita ion of required size consisting of 35mm thick solid PVC sandwich , complete all as specified and directed by Engineer in charge.

M & L for 75mm Hasp and staple, safety type, stainless steel with stainless steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F 75mm long stainless steel, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 100 mm butt hinges stainless steel complete all as specified and directed.

S&F stainless steel of 150mm long decorative type handle fixing,complete all as specified and directed.

S&F stainless steel of 200mm long barrel tower bolt fixing,complete all as specified and directed.

S&F stainless steel, sliding door bolt of 300mm long bolt plate type decorative with bright bolt not less than 12mm dia with and including min of 6 bolts and nuts, four on bolt plate and two on staple fixing, complete all as specified and directed.

S&F of door stopper 14cm long of aluminum alloy and tongue, anodised with hard drawn steel spring, foxed in floor etc. complete as specified and as directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned stacks, or galvanised wire staples etc complete all as specified and directed.

S & F mild steel work such as window guard bars, ladders and similar work conforming to Fe – 290 Grade – E 165 complete all as specified and directed.

S&F of medium weight, cold rolled mild steel , SS finish , (Particle overlay fully overlay of any type ) diameter of cup 35mm, hinge cup depth 11.5mm, soft-closing hinge complete all as specified and directed Make:- Godrej kitchen fitting or techno equivalent in sleek by asian paints or techno commercially equivalent make as listed in list of makes

S&F for stainless steel of 304 grade electro -polished for corrosion resistance modular thali holder / basket having size of 42x58.5 x20cm including telescopic drawer having weighing capacity of 6 kg complete all as specified and directed Make:- Godrej kitchen fittings or techno equivalent in sleek by asian paints or techno commercially equivalent make as listed in list of makes

S&F for stainless steel of 304 grade electro -polished for corrosion resistance modular cup & saucer holder / basket having size of 52x53.5 x10cm with telescopic drawer charnel having weighting capacity of 4 kg ,complete all as specified and directed Make:- Godrej kitchen fittings or techno equivalent in sleek by asian paints or techno commercially equivalent make as listed in list of makes

S&F SS of 304 grade 200mm length stainless steel cabinet drawers handles ,complete all as specified and directed. Make:- Godrej kitchen fittings or techno equivalent in sleek by asian paints or techno commercially equivalent make as listed in list of makes

S&F of stainless steel grain trolley SS 304 grade having size 525x485x350mm, with heavy duty and steel with finish of zinc , corrosion resistance with telescopic drawer channel having weight capacity of 25 kg ,complete all as specified and directed Make:- Godrej kitchen fittings or techno equivalent in sleek by asian paints or techno commercially equivalent make as listed in list of makes

S&F of stainless steel plane wire basket / trolley SS 304 grade having size 506x480x200mm, with heavy duty and steel with finish of zinc , corrosion resistance with telescopic drawer channel having weight capacity of 25 kg complete all as specified and directed Make:- Godrej kitchen fittings or techno equivalent in sleek by asian paints or techno commercially equivalent make as listed in list of makes

S&F of stainless steel modular performed cutlery basket / trolley SS 304 grade having size 520x485x100mm, with heavy duty telescopic drawer channel having weight capacity of 6 kg complete all as specified and directed Make:- Godrej kitchen fittings or techno equivalent in sleek by asian paints or techno commercially equivalent make as listed in list of makes

S&F of stainless steel 304 grade size 180x515x485 mm, pull out detergent rack having two shelf spacers with telescopic drawer channel having weight capacity of 6 kg ,complete all as specified and directed by Engr-in-charge. Make:- Godrej kitchen fittings or techno equivalent in sleek by asian paints or techno commercially equivalent make as listed in list of makes

Taking down rolling shutter of any description exc 2 sqm but n exc 5 sqm each and removing to store from site complete all as specified and directed

S&F Rolled mild steel Framed work as in doors or gates of angle or other section Fe-410-W(Gde-E-250)Quality-B with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (including steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed.

M&L for Rolled mild steel framed work in tubular trusses such as roof trusses,trussed,purlines, crane gantries, rails and fastenings and heavy bracket framing including distance pieces, cleats etc including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St 240 complete all as specified and directed.

M&L for preparation of new or previously untreated steel and Iron surface of any description, not otherwise described over 10 cm width or girth and applying two coats of Synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old steel and iron surfaces of any description not otherwise described, over 10 Cm width or girth and applying one coat of synthetic enamel paint 1st quality complete all as specified and directed

Cutting Holes in brick walls built in cement mortar superficial area n exc 150 sqcm complete all as specified and directed

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified & directed .

S&F table top WHB, vitreous china, white flat back of size 550mm x 400 mm x 140 mm including 32mm nominal size copper alloy, nickel chromium plated finish waste fittings including s&f of fittings and brackets, sealing gap between wall and table top basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste fitting etc with silicone sealant , complete all as specified and directed

Supply & fixing in repair 10 ltr capacity, low level, symphonic type, white twin flushing cistern confirming to as per IS 7231 :1994 with intel , ball valve, float and handle including brackets and 40mm nominal dia high density polyethylene pipes for flush pipe , complete all as specified and as directed .

S&F vitreous china squatting pan"Orissa" pattern of size 580x440mm white with integral foot rests(excluding flushing cistern and flush pipe) with 'P' or 'S" trap front or back inlet etc including connection to trap and flushing pipe and provision of cement concrete bedding complete all as specified and as directed in repairs including demolition of existing one.

Supply & fixing in repairs white vitreous china wash down water closet pan floor mounted type of size 645x355x675mmm with "P" of "s" trap, plastic water closet seat cover (soft landing), and mild steel chromium plated or aluminised hinging device , including making all necessary connections etc complete all as specified.Make – Cera Cat Part No S1013201 or of Techno Commercially equivalent in other make as listed in list of makes.

Supply & fixing in repairs vitreous china wash down water closet pedestal pattern white excluding fixing bolts, including flushing cistern and flush pipe complete and including PVC seat cover with aluminium/PVC hinging devices & etc complete all as specified. Make – Hindware Cat part no 20044 or Techno commercially equivalent in other make as listed in list of makes.

S&F in repair 15 mm bore fancy type bib taps cast copper alloy 15 mm bore with fancy chromium plated screwed down , screwed for iron pipe or for brass ferrule complete all as specified and as directed Make:- CERA Cat part No. F 1015151 or Techno commercially equivalent in other make as listed in list of makes.

S&F in repair 15 mm bore fancy type bib taps long body (two in one) cast copper alloy 15 mm bore single handle and wall flange with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed Make:- CERA Cat part No. F-1015163 of Techno Commercially equivalent in other make as listed in list of makes.

S&F in repairs stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) for 15mm bore pipe, screwed both ends including necessary fittings such as sockets for pipe or for union all complete as specified and as directed.

S & F in repair 15mm bore PVC Connection with PTMT nuts of length 600 mm complete all as specified and directed

S&F in repair 15 mm bore fancy type angular valve cast copper alloy screwed down , high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified and as directed by Engr-in-charge . Make:- Cera Cat part No.F-1015201 of Techno Commercially equivalent in other make as listed in list of makes.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

Supply and fix for central hole basin mixer, cast copper alloy with capstan head , chromium plated screwed down, high pressure with or without lettered "hot" or "cold" with long screwed shank and fly nuts screwed for iron pipe of 15mm bore complete all as specified and as directed. Make:- CERA Cat part No. F-1012451 of Techno Commercially equivalent in other make as listed in list of makes.

S&F Toilet Paper Holder chromium plated, including all necessary fittings, connections etc.Make – Jaquar Cat Part No CAN 1151N or Techno Commercially equivalent in other make as listed in list of makes.

S&F in repairs Towel Rail 600 long chromium plated, including all necessary fittings, connections etc.Make – Cera Cat Part No F5003103 or Techno Commercially equivalent in other make as listed in list of makes.

S&F in repairs of sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long. Complete all as specified and as directed.

S & F in repairs Towel Ring Round chromium plated , including all necessary fittings, connections etc.Make – Jaquar Cat Part No AQN 7721 or Techno Commercially equivalent in other make as listed in list of makes.

S&F in repairs PVC mirror cabinet of size 350x450 mm complete all as specified and directed. (Make - Cat No 551 of Prayag or Techno Commercially equivalent in other make as listed in list of makes.

S&F in repairs stainless steel soap dish, complete all as specified and as directed.

S&F in repairs of Chromium plated over head shower rose with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified. Make Cera Cat no. F7010213AB or Techno Commercially equivalent in other make as listed in list of makes.

S&F in repairs 15 mm Brass CP single lever Wall mixer long body three in one with arrangement for both telephonic shower and overhead shower with bend pipe and connected fittings for mixing hot & cold water screwed down for iron pipe. (Make Cera Cat no. F-1003403 or Techno Commercially equivalent in other make as listed in list of makes.

S & F in repair stainless steel (AISI-304 grade) square grating with frame of size 150 x 150 mm, complete all as specified and as directed.

M&L for cement concrete type C-2 1:3:6, using 40mm graded stone aggregate as in surface channel. Complete all as specified and as directed.

M&L for Double nosing and stepping stone 15 mm thick of colour as approved as in treads of stair case set and jointed in neat cement slurry over and including 10 mm thick screed bed for laying floor finishes in cement mortar 1:4 complete all as specified and as directed.

S&F of Curtain rod of stainless steel 25 mm dia chromium plated with fixing brackets, stop, rollers, clamps etc. complete all as specified and as directed.

S&F in repair stainless steel curtain rod holding brackets heavy duty fixed to wall with stainless steel screws etc, complete all as specified and as directed.

S&F in repair stainless steel finial type fancy stop and suitable for curtain rod 25mm dia etc, complete all as specified and as directed.

M& L for stainless steel Framed work such as Stairs railing (framed) including stringers, treads, landing, balusters, hand rails etc of Ornamental stainless steel of grade 304 as approved design / drawing etc complete all as specified and directed. Note:- Design and pattern shall be approved by Engr-in-charge /GE at the time of execution of work.

S & F for 3mm thick Poly Carbonate sheet (Compact clear / Bronze sheet ) such as grills, gratings, chajja etc. fixed with self tapping screws or nut and bolts, complete all as specified and directed

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

Taking down PVC soil pipe with fittings from wall, trenches of any description including fittings complete all as specified and as directed.

S & F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/ ceilings or laid on floors complete all as specified and as directed.

S&F 110mm dia PVC bends of bends of any radius.

S&F 110mm dia PVC (SWR) branch piece single (single 'Y'/T) equal or unequal with access door complete all as specified and as directed.

S&F 110mm dia PVC SWR vent cowl complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/ceilings or laying in floors etc. complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

M&L for point wiring complete for one power point for one metal plug & socket for AC or one socket for geyser point on independent board with 4.0 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 4.0 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, including cutting chases of existing wall for conduits and fixing for Metal Plug and socket boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be done through proper size copper/brass thimbles.

M&L for point wiring with 1.5 sqmm single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI Marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI Marked) with proper colour coding as earth continuity conductor connected to common earth dolly, modular sheet steel sunken terminal box of appropriate size suitable for modular switch/ fittings concealed in walls, with modular back plate, top cover fixed flush to wall for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles all as specified and as directed for the following :- (a) One light point controlled by one way switch 5/6 amps.

All as per item No 127 above but One ceiling fan/Exhaust fan point controlled by one way switch 5/6 amps.

All as per item No 127 above but One socket out let 5/6 amps point on the independent board

All as per item No 127 above but One socket out let 5/6 amps point on the same board

All as per item No 127 above but One bell point controlled by one way switch 5/6 amps.

All as per item No 127 above but One light point controlled by two way switch 5/6 amps.

All as per item No 127 above but wiring with 2.5 sq mm single core multistranded copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and directed

S&F of Modular switch, single pole, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular switch, single pole, Two way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular switch, single pole, one way, 16 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 5 Pin, 6 Amp, 2 Module, 230 volts, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 6 Pin, 6/16 Amp, 2 Module, 230 volts, (ISI marked) complete all as specified and as directed.

S&F of Modular bell push, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of stepped type modular electronic fan regulator 120 watt 2 module suitable for 1200/1400 mm sweep energy saving fans,ISI marked complete all as specified and directed.

S & F Call bell Ding dong, 230 Volt single phase all as specified and directed.

S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and directed.

S&F LED white glass Lamp 1x9 Watt 230V Base-22 complete all as specified and directed.

S&F in ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed.

S&F IP 20, class I, LED light 1X20 W (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified.

S&F LED Mirror light fitting 1 x 10 W, (or nearest next higher wattage) 5700 K, wall /Surface mounted with aluminium housing 2 feet long, integrated type, with high efficiency PMMA diffuser, integrated high efficiency electronic driver & surge suppressor of 2 KV or more, luminaire efficacy > 95 lumens/Watt, power factor >/ 0.90, operating range – 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/square blocks, screws etc complete including 01 No 10 W LED lamp with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size including necessary taking down the old unserviceable fitting complete all as specified.

S&F of Bulk head luminaire suitable for 10 Watt LED (or nearest next higher wattage) light IP66 grade, luminaire efficiency not less than 120 lumens/watts with and including 10 watt LED (or nearest next higher wattage) lamp and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor from ceiling rose to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified.

Fixing only LED Tube light of any watt on wall/surface mounted fixed with 02 Nos of PVC round/ square blocks, screws etc complete all as specified.

S&F of Decorative wall light fixture made up of polycarbonate suitable for 15 Watt LED retrofit of type B-22 base, IP66 grade, with and including 15 watt LED (or nearest next higher wattage) lamp and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified. Make - Havells , CAT No - LHFOECE1TZ1B014 or Techno commercially equivalent in other make as listed in list of makes.

S & F Energy saving new generation environmental friendly long life versatile pressure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete including removal of old unsv fitting all as directed by Engineer-in-Charge.

Taking down carefully Ceiling fan from its original position and refixing / hanging after B/R plaster work complete all as specified and directed.

M&L for painting of ceiling fan of any sweep complete, in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc, all as specified and as directed.

Material and labour for concealed sub-main wiring two runs 10Sqmm for main and one run of 10 Sqmm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete, including taking down old unsv aluminium submain wiring all as specified and as directed. NOTE : Two runs of 10 sqmm conductor for main and one run of 10 sqmm conductor as earth wire with proper colour coding including one run of PVC conduit shall be measured as one unit length. Connections of cables with MCBs or bus bar shall be done through appropriate size brass/ copper thimbles

S & F in replacement of MCB, DB Vertical TPN, 415 volts 4 ways (8+18 WAYS), DOUBLE DOOR, IP-43, with MCCB Incomer, metal door, rated bus bars, earth bar, neutral links complete including blanking plates as required & fixed flush to wall/other surface complete all as specified and as directed.

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, Triple pole & neutral with 200 amps rated bus bar, 415Volt IP-20 protection suitable for fixing MCB"S/lsolators with and including taking down old one complete all as specified and directed.

Supply and fixing of moulded case circuit breaker (MCCB) four pole Adjustable type 415 volt, 50 Cycles, 125 Amps of breaking capacity 36 KA after and including taking down / dismantling of old existing unserviceable one complete all as specified and as directed.

S&F in replacement of MCB, Triple pole & neutral 63 amps, 240 volts, ‘C’ curve, 10KA complete all as specified and as directed. Make :L & T ,Cat No: BB40630C or Techno commercially equivalent in other make as listed in list of makes.

S&F MCB, Single pole & neutral, 32 to 63 amps, 240 volts, ‘C’ curve, 10KA all complete with and including taking down old unsv one as specified and as directed.

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete with and including taking down old unsv one as specified and as directed.

M & L for sheet metal enclosure fabricated out of 2.0 mm thick CRCA sheet, totally enclosed type, dust & vermin proof, with suitable sized supporting MS angles & suitable openings at top & bottom for entry of outgoing / incoming cables, fixed with nuts & bolts & front side openable with hinged shutter with suitable locking arrangement duly painted with 2 coats of powder coated paint over a coat of red oxide primer (spray paint) with minimum dimensions (90 x 75 x 20 cm ) flush to wall for incorporating 01 No TPN DB, 04 Nos electronic meters etc complete all as specified and as directed.

Material and labour for earthing complete with galvanized steel plate electrodes of size600x600x6mm thick buried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised wire 4.00 mm earth lead by means of nuts, bolts, checknuts and washers including 15 mm bore galvanized iron pipe, medium grade for protection of earth lead upto the length of 7.5 meter towards test terminal and 20 mm bore galvanized iron pipe, medium grade for watering, and providing of charcoal and common salt in alternate layers, including necessary earth work in any type of soil and including PCC pit in PCC 1:2:4 with provision of wire mesh and funnel, complete all as shown in electrical plate No 03 of SSR Part- I including testing on completion all as directed and as specified.

S&F exhaust fan with louvers 250 mm sweep (Plastic rust proof Body and blade), BLDC Fan, energy efficient, AC single phase 240 volts, 50Hz,, Air Delivery – 860 CMH and connecting up complete including built in louvers and provision of 3 core flexible multistranded copper conductor of size 0.75 Sqmm from ceiling rose to fan all as specified and as directed.

S&F heavy duty exhaust fan 300 mm sweep MS body with antidust painting, 4 blade with heavy duty motor and double ball bearing, 1320 RPM, single phase 230/240 volts copper wounds, Air delivery -1600 CMH complete with all accessories as bird guard/ louvers shutters etc including making connections with 3 core flexible multistranded copper conductor of size 0.75 Sqmm run through flexible pipe all as specified and as directed including cutting holes and making good the disturbed surfaces of walls in CM(1:4) and finishing the surface as per existing color scheme complete all as specified and as directed.

S&F epoxy powder coated sheet metal enclosure with socket plug top and MCB, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 32 Amps, 240 Volts, C Series current carrying capacity 10 kA, including necessary connection complete all as specified and directed.

S&F of Bulk head luminaire with B22 base holder suitable for 9 Watt LED inverter type bulb light IP66 grade, with and including 9 watt LED (or nearest next higher wattage) lamp (LED Bulb with B22 base 900 Lumens in normal mode and 450 lumens in power back up mode, charging time 8-10 Hrs and around 4 Hrs Power backup with inbuilt surge protection of 3 KV) (or nearest next higher wattage) and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor from ceiling rose to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified.

Taking down Electric meter three phase any capacity/size disconnecting electrical connections and refixing the same all as directed

S & F non-metallic rigid PVC medium grade 20mm dia conduit and conduit accessories (ISI Marked) concealed in wall including cutting chases etc all as specified and as directed.

S & F Post top lanterns 20 watt LED light fitting ,new generation, energy saving, environmental friendly, longlife with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source, spun aluminium canopy, with opal/clear acrylic diffuser and complete with all accessories internally prewired including connecting up with three core twisted flexible copper conductor cable up to ceiling rose and necessary mounting arrangements, complete all as directed by Engineer-in-charge.Make :Havells,Cat part No RUBYMINIPT15WLED757PSYMTOPC or Techno commercially equivalent in other make as listed in list of makes.

M & L for PVC insulated unarmoured copper conductor cable 4 sq mm 2 core complete all as specified & directed.

Taking out old unserviceable GI Pipe of any size from site complete all as specified and as directed. Note : The Excavation and earth work shall be measured and paid separately under relevant item of Schedule.

Supply and lay pipe galvanized Medium grade including fittings 25 mm fixed to walls and ceiling or laid in floor Complete as specified and as directed

Supply and fix 25mm dia Gun metal globe Gate Valves with iron wheel head of 25 mm dia bore complete with all accessories all as specified and directed

M& L for cutting existing GI pipe alteration or addition of 40/50 mm dia bore for insertion of reducer Tee complete with all accessories all as specified and directed

Excavation in trenches in soft/loose soil not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out for taking up / laying under ground electric cable complete with all accessories all as specified and directed

Returning, filling in, including spreading leveling watering and well ramming in layers not exceeding 25 cms in depth complete with all accessories all as specified and directed

Removing excavated materials n.exc 50m and depositing were directed at a level n.exc. 1.5m above the starting level complete all as specified and as directed

Taking out old unserviceable cable of any size carefully from trenches after disconnecting electric connection, GI pipe protection, with and including separating serviceable bricks & set aside and removing un-serviceable bricks from site complete all as specified and as directed. Note : The Excavation and earth work shall be measured and paid separately under relevant item of Schedule.

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated PVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 50 sqmm 3.5 core with and including all fixing & connecting accessories such as Aluminum cable lugs, cable gland, nut, bolts, washer etc complete as specified and as directed. (NOTE: Earthwork & Excavation, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule 'A').

Supply and lay dry river sand filling for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed.

Supply and laying sub class B bricks of size 25cmx12.5cmx7.5cm (+/-10% tolerance) for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified and as directed.

M & L for horizontal boring across the existing road without disturbing the road surface for inserting 20mm dia GI pipe complete all as specified and as directed. Note :- (i) Removal of surplus soil shall be deemed to be include in the unit Rate. (ii) GI pipe will be measured and paid separately under relevant item of Sch 'A'.

M&L for 50 mm bore steel tubing light grade ISI marked for protection of cable including necessary joints complete all as specified and as directed.

Supply and fixing of moulded case circuit breaker (MCCB) four pole Adjustable type 415 volt, 50 Cycles, 200 Amps of breaking capacity 36 KA after and including taking down / dismantling of old existing unserviceable one complete all as specified and as directed.

L. B. SHARMA (BID ID -3333247)

S.N. GHOSH AND CO. (BID ID -3332220)

BBKundu (BID ID -3332638)

R K AGARWAL (BID ID -3331597)

M/s. RAMPHAL GARG (BID ID -3331443)

S K GUHA (BID ID -3329110)