Repairs/Renovation of industrial canteen kitchen area except dining hall area inside factory at AFK.

Amount

Taking down existing chowkats or frames exc. 1.5 sq.mt. but not exc. 4 sq.mt. each with shutters (with out taking off shutters from the frame)

Taking down shutters of any description exc 1 sq. m and n exc 2 sq.m each

Dismantling structural steel work including doors, windows, gates but excluding framed truss etc.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Dismantling of stone slabs and tiles (shahbad tiles) of any description or thickness in floors, aprons etc. laid, bedded and pointed in cement mortar.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level).

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key , scrubbing down with water etc. to receive plaster etc. complete.

M&L providing precast cement concrete type C1, 1:3:6 (20mm graded aggregate) in block masonry with solid blocks, exc 10cm width and setting in cement mortar 1:6, complete

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces of walls in CM 1:4 including finishing the surface rough finished as directed.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces of walls in CM 1:4 including finishing the surface even and smooth without using extra cement.

M&L for providing cement concrete type B 1:2:4mix (20mm graded aggregate ) in foundations, filling and mass concrete fair finished with necessary centering.

M&L for screed bed or bedding layer of mortar 20mm thick for laying floor finishes in CM 1:4

M&L for Glazed ceramic coloured tiles in vertical surface 350mmx 250mmx 7mm / 450x350x7 mm thick, joint free, coloured tiles , set and jointed in neat cement slurry and pointed in white or coloured cement to match. (Make Johnson , Kajaria, Bell)

M&L for Jhonson endura tiles 300mm x 300m x 20 mm thick with fixing using neat cement slurry and chemical and joint filling with approved sealent make -latticrete, saint gobain, roff etc. Thk of joint 3mm to 4mm with spacers

M/L for Virified Ceramic Tiles light/ dark/ any shade 10mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 Sqm, in floors etc in light shade, set jointed in neat cement slurry and pointed in white or coloured cement to match. (Make- Johnson, bell, Kajaria)

Filleting in any position and any shape in cement mortar 1:4 n ex 25 sqcm (for filling of skirting top/ paver block)

S&F Mild steel of grade Fe-290-(Gde E-165) for framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc, complete, drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (inclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete.

S&F Mild steel of grade Fe-290-(Gde E-165) for framed work such as grills, gratings, etc. with end of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, door frames, window-cill, cooking platform/ washing area and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite.

M&L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

M&L for 4mm thick Non asbestos fibre cement plain building boards, fixed or laid/ inserted to timber/ GI/ Aluminium frame work with screws in ceiling.

S&F Powder coated aluminium sliding windows/ventilators three track (01 gauged and 02 glazed shutters ) including glazed panel shutter of standard section of jindal or equivalent with 4mm thick ordinary plain glasses fixed with rubber linning angles cleat and locking arrangement including pvc ball bearing, including aluminium grill stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apreature 1.40 mm etc, making good to the disturbed surface and match with existing surfaces complete all as specified and directed.

M&L design, supply and installation of fully glazed/ partly glazed/ partly panelled/ fully panelled aluminium powder coated partition for cabins comprising of : Aluminium powder coated extruded rectangular tube section of size 2.5"x1.5" (16 gauge) for vertical and horizontal top and middle member (rails). Bottom panel 1.20m high (or as directed by Engineer-in-Charge) with 3mm thick Aluminium Composit Panel (ACP) of approved quality and colour finished on both side and fixed with glazing clips / slip cleates and rubber stopper etc.Middle Panel approx 0.90m high (or as directed by Engineer-in-charge) with 5.5mm thick plain transparant glass and fixed with galzing clips/ slip cleates and rubber stooper etc.Top panel 0.90m high (or as directed by Engineer-in-charge) with 3mm thick aluminium composite panel(ACP) both sides same colour finished with glazing clips/ slip cleates and rubber stopper etc. Make- Aluminium section - Jindal ACP- Alcobond , Timex, Flexibond.

M&L design, supply and installation of partly panelled, partly glazed aluminium single/ double leaf door comprising of : Powder coated Aluminium extruded rectangular tube section of size 2"x2"x16 gauge for vertical and horizontal top and middle member (rails) and 6"x2"x16gauge for bottom horizontal member. Glazing strips bottom panel approx 1.20m high (or as directed by engineer-in- charge) with Aluminium Composite panel 3mm thick approved quality and colour finished on both side and fixed with glazing clips/ slip cleates and rubber stopper etc. Top panel approx 0.90m high with 4mm thick plain glass pan with glazing clips/ slip cleates and rubber stopper etc. complete Door handel American type all other door stopper , door closer, Everest/ opel make and lock & key " surya Make" all as specified and directed by EIC. Glass - Modi , saint Globin. Bottom panel 1.20m high (or as specified by Engg-in-Charge) with Aluminium Composite panels 3mm thick of approved quality and colour with both sides finish and fixed with glazing clips / slip clits and rubber stopper etc. Top panel 0.90m high with 6mm thick plain glass panes with glazing clips / slip clits and rubber stopper etc. complete. Door handle 'American type' and all other door fittings etc.complete. viz. pivot, base pivot, door stopper, door closer 'Everest/opel' make and lock & key 'Surya make' all as specified and directed by Engg-in-Charge. Aluminium section:Jindal. Glass:Modi/Saint Gobin

S&F Door closer hydralically regulated, Aluminium ( extruded section) body, designation No.3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed.

Stainless steel 304 material railing at staircase of ht. @ 1.0 m with top rail pipe 50 mm bore ( 16 gauge). Vertical pipe 38 mm bore ( 16 gauge) @ 1.0 m c/c and two longitudnal parallel pipes of size 25 mm bore ( 16 gauge) including Tee, cross, bend, base coupling, fixed in floors with necessary fasteners for enchoring in floor and walls etc complete mat finish.

M&L for providing edge moulding/ groove cutting to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish granite stone or any description etc. complete.

M&L for preparation of new or previously untreated steel or iron surfaces of any description, not otherwise mentioned over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer.

M&L for preparing plastered or unplastered old surfaces and applying one coat of oil emulsion distemper on ceiling.

M&L for preparing plastered or unplastered old surfaces and applying one coat of oil emulsion distemper on walls.

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm

S&F Pillar taps cast copper alloy fancy type chromium plated screwed down high pr. With or without letterede 'hot' &' cold' with long screw shank and fly nuts, screwed for pipe and fixed in repair, bore dia of pipe 15mm.

S&F of Flush pipe of polyethylene of low or high density or PVC 32mm dia, for low level cistern/wash basin/sink/urinal.

S&F PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement diameter of outlet = 75mm.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors 75mm bore.

S&F PVC (SWR) bends any radius bore of pipe 75mm.

Removing surplus excavted and demolished material up to a distance exc 500 m but n exc 1.50 km and depositing where directed soil,,P.C.C,Debris etc.

Credit Item-Dismantled mild steel member/ wrought iron doors/ windows (of any description) obtained from dismantling

Credit Item-Dismantled door frames with shutters of any description area exc 1.5 Sqm but not exc 4 Sqm.

V C SHETH (BID ID -911373)

UNICON (BID ID -903654)

SHAILENDRA B TULSANI (BID ID -911869)

M/s S D NAGAR (BID ID -911200)