REPAIRS TO BROKEN SLABS, EDGES, DRAIN, COVER SLABS, FOD TRAPS ETC AT TECHNICAL AREA AF STN BAREILLY UNDER GE(AF) BAREILLY

Amount

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for including removal of debris from site to outside MoD land.

M&L for cement concrete work in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete more than 25 cm complete all as specified.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified.

M&L for laying 400 micron thick transparent high density polyethylene (HDPE) film sheet, grade-I confirming to IS-10889 with side lap of 160 mm and end lap of 300 mm complete all as directed. (Net area excluding the overlaps shall be measured and paid).

M&L for 10 mm thick layer of river sand over concrete including watering and compacting all as specified.

M&L for finishing surfaces of concrete road, pavements etc by brooming while the concrete is still green all as specified.

M&L for forming 20 mm thick expansion joint in 150 mm thick cement concrete slab & filled with pre-formed bituminous filler board and top 30 mm primed and sealed with sealing compound grade 'A' complete all as specified.

M&L for forming contraction (dummy) joints 100 mm deep X 10 mm wide and filled by sealing compound grade 'A'complete all as specified.

Demolition of brick work built in cement mortar or cement lime mortar including all quions, arches, pillers etc complete including removal of debris from site to outside MoD land.

M&L for brick work with sub-class `B' bricks, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:6 all as specified.

M&L for 15 mm thick rendering on other than fair faces of brick work or stone masonry surfaces in cement mortar 1:4 including finished even and fair without using extra cement all as specified.

Taking down cement plaster on brick or stone walls including raking out joints,hacking for key,scrubbing down with water etc.including removal of debris from site to outside MoD land.

M&L for prepration of newly plastered surface of wall and applying two coats of cement base paint complete all as specified.

M&L for cement concrete type B-2, 1:2:4 mix (using 40 mm graded stone aggregate) in foundations, filling and mass concrete all as specified.

M&L for cement concrete 1:2:4, type B-1using 20 mm graded stone aggregate as in lintel upto1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lasing courses, parapets and railing upto 60 cm in height, coping, kneelers, apex stones, bed plates, water troughs and like including weathering, slightly rounded or chamfered angles and throating as directed.

Dismantaling of bricks (laid flat or on edge) or brick tiles bedded and pointed in cement mortar as in floors channels, kerbs, aprons etc all as specified and directed.

M&L for laying bricks flat, using sub class 'B' old size bricks, bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 as in lining for drain including necessary surface dressing if required in any type of soil complete all as specified.

All as per item No. 17 here-in-before but except bricks. [Note: Old serviceable bricks obtained from dismantling shall be re-used under this item].

M&L for laying bricks on edge, using sub class 'B' old size bricks, bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 as in lining for drain including necessary surface dressing if required in any type of soil complete all as specified.

All as per item No. 19.00 here-in-before but except bricks. [Note: Old serviceable bricks obtained from dismantling shall be re-used under this item].

Demolition of reinforced cement concrete in any position and any description including cutting of reinforced bars to facilitate demolition and removal of debris from site to outside MoD land all as specified

M&L for providing pre-cast cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate as in landing, cover slabs,chullah hoods, chajjas, shelves and similar items with plain faces in cement concrete and setting in cement mortar 1:6 complete all as specified.

M&L for mild steel TMT bar 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips all as specified.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished surface of concrete all as specified.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified.

S&F for rolled mild steel sections as in joist, channel, angle, or tee sections fixed independently, without connecting plates, drilling holes for anchor bolts etc (cut to ordinary lengths i.e within 20mm of the length indicated) and conforming to Fe-410 W (Gde E-250) quality-B complete all as specified.

S&F for rolled mild steel framed work as in doors or gates, cover of angle or other section with gusset plates, rails, braces, locking arrangment, sliding bolt etc complete, drilled or welding for fixing of steel sheeting or other connected items of doors, etc to be prapared for hanging or sliding with and including either hooks and hinges ( type/pettern as approved by GE) or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides ) and make it complete for fastening and fixing complete Fe 410-W (Gde-E-250) Quality A, as in existing main horizontal /vertical sections, bracing plate at bottom for wheel fixing of MS framed structure of doors and other connecting plates and welding wherever required after making them prefectly straight and alingned complete all as specified and directed.

S&F for rolled mild steel as in plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices, angle brackets cleats and other connections and conforming to Fe 410-W (Gde E- 250) quality-A complete all as specified.

M&L for reinforced cement concrete nominal mix 1:1.5:3 type A-1 using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.50 mtr span and the like complete all as specified.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified.

All as per item No. 30.00 above but for TMT bars 8 mm dia and over as in stirrups, spacer and binders all as specified.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished surface of concrete complete all as specified.

M&L for preparation of newly steel surfaces of any description over 10 cm in width or grith not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer all as specified.

PRASHANT A TO Z TRADERS (BID ID -3475552)

M/s Agarwal Builders (BID ID -3480774)