Construction of Veterinary Hospital Building at Nagrota Bagwan in Distt Kangra (HP) (SH- Construction of Civil work including water supply and sanitary Installation, Rain water Harvesting system and boundary wall etc)

Amount

Excavation in foundation, trenches etcetera. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, shoring, strutting or bailing out water (Surface and sub soil water) upto any depth or height any quantum of water including de-watering removal of slush, lift upto any height, stacking the excavated soil clear from the edge of excavation and then retuning the stacked soil in 15cm (Fifteen centimetre) layers, when required into plinths, sides of foundation etcetera; consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by the Engineer-in-charge, within all leads, lifts and other incidentals as per specifications, approved drawing, design. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Excavation in hilly area in all heights and depths and in all kind of soil by manual/mechanical means including saturated soil comprising of ordinary soil, soft rock, hard rock, chiseling, wedging out of rock (where blasting is prohibited) and their intermediate classification of soil, setting out true to the required lines, grades, width cutting and trimming of side slopes and level as shown in the drawing and as directed by engineer-in-charge at site according to the MORD technical specification clause 302, 1603.1 and 1603.2 and sorting out useful materials and stacking the same in all leads and lifts in acquired width of road and transportation of un-useful material for filling in road ways, camber, embankments for grade improvements and disposal of all surplus material to required width of the road or on approved dumping sites through all modes of transportation including head load or animal transport or mechanical means along with its leveling, fine dressing and carriage of machineries, materials, tools, equipments and safety measures and incidentals necessary to complete the work by mechanical means and /labour if required as per specifications, approved drawing, design, specification and as per the entire satisfaction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Excavation in drains and channels etcetera; in earth work in all kind of soil, such as pick work, jumper work, pick jumper work, blasting work, hard and soft blasting and work doing in saturated soil including chiseling or wedging out rocks where blasting work is prohibited including shoring, strutting and pumping or bailing out water (Surface and sub soil water) upto any depth or any height any quantum of water including slush which may arrise during dewatering any other mixed variety of soil, lift upto any height, stacking the excavated soil for all heights from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimetre) layer when required into plinths, sides of foundations etcetera; consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as per specifications, approved drawing, design, specification and as per the entire satisfaction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Excavation in earth work and filling in 15 cm (Fifteen Centimetres) layers in foundation and plinths including ramming, watering and consolidating upto all leads, lifts and then in pick work complete including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Sand filling under floor including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like as per Architectural drawing, design and specifications including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera; with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders lintels where ever required sides and soffits of beams haunchings cantilevers bressumers and lintels upto all depths including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts square rectangular polygonal in plan including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in vertical fins and vertical sun breakers complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres),so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing, including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in edges of slab and breaks in floors and walls under any thickness including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:6:12 (One cement : Six sand : Twelve graded broken/crushed stone aggregate 40mm (Forty millimetres) nominal size mechanically mixed and curing complete excluding cost of forms work centring, shuttering in foundation and plinth including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (One cement; four sand; eight graded crushed stone aggregate 40mm (Forty millimetres) nominal size mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Stone filling in plinth dry hand packed with hard stone approved quality under floor including watering, ramming, consolidating and dressing complete as per specifications, approved drawing, design as per entire satisfactions and direction of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the minimum ccompressive strength of 20N/mm2 (Twenty Newton per square millimetre) with cement contents not less than 330 kg (Three hundred thirty kilogram) per cubic metre to give a smooth surfaces mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in foundation, footings, bases of columns and the like mass concrete in all depths/thickness upto all floors levels as per specifications, drawing, design as per entire satisfaction and direction of Engineer-Incharge including carrige of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M-Twenty) design mix to obtain the minimum comressive strength of 20N/mm2 (Twenty Newton per square millimetre) with cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic metre, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landings, shelves and their supports balconies, beams, girder, bressumers and cantilevers in all depths/thickness upto all floor levelas per specifications, approved drawing, design as per entire satisfaction and direction of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M-Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty Newton per square millimetre) with cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in columns, pillars posts and struts in all depth/thickness for all floors heights as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge including incidents. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty Newton per square millimetre) with cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic metre, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in vertical and horizontal walls/fins (thickness not more than 0.10m) (Zero point one zero metre) including attached pilasterd buttersses plinth and string courses etc. from top of foundation individually or forming box louvers and projected band upto all floor level as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty Newton per square millimetre) with cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic metre mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in Stair cases (except spiral stair cases) excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor levels as per specifications, approved drawing, design including carriage of material within all heights leads, lifts and other incidentals and as directed by the Engineer-in-charge including incidents. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M-twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty Newton per square millimetre) with cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed, vibrated and curing complete for reinforced concrete in Chhajjas for all thickness in all floor levels up to all heights including finishing the exposed surface with cement mortar 1:3 (One cement : Three sand) to give a smooth and even surface including centering/ form work but excluding the cost of reinforcement for reinforced concrete work up to all floor levels up to all height as per direction of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and specifications. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work M-20 (M-twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty Newton per square millimetre) with cement contents not less than 320 Kgs (Three hundred twenty kilogram) per cubic metre mechanically mixed and vibrated to give smooth and even surfaces including centring, shuttering but ecluding the cost of and reinforcement as in mouldings, cornices, windows sills etcetera to any girth, as per specifications, drawing and design complete, as directed by the Engineer-in-charge.upto floor all levels including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying Tor steel reinforcement of TATA/Sail/Tisco for reinforced cement concrete work including bending, binding, cutting, straightening and placing in position complete including cost of binding wires complete upto all floor levels as per specifications, approved drawing, design, as per entire satsfaction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Random rubble masonry coursed with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 1:2:4((one cement: six sand: twelve graded crushed stone aggregate 20 mm (Twenty milimetres nominal size) raking out joints in cement mortar 1:6 (One cement : Six sand) and curing complete within all heights leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge including incidents..

Providing and laying Damp Proof Course 38mm (Thirty eight millimetres) thick with cement concrete 1:2:4 (one cement: two sand: four graded crushed stone aggregate) 12.5mm (Twelve decimal five millimetres nominal size) thick and curing complete, as required at site including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Applying a coat of hot bitumen mexphalt 80/100 (Eighty/Hundred) or equivalent using 1.70 Kgs. (one decimal seven zero Kilogram) per square metre on Damp Proof Course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil, including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing glass strip in plinth protection in following blocks, fixing and finishing in cement mortar 1:3 (one cement : three sand) 40 mm (Forty millimetres) wide and 6 mm (Six millimetres) thick etc. complete, excluding plastering of the jambs sills and soffits, including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Second class brick masonry using common burnt clay building bricks in super-structure upto any floor level in cement mortar 1:6 (One cement: Six sand) and curing complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Second class half masonry using brick common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:4 (One cement: Four sand) with hoop iron and curing complete including carriage of material within all leads, lifts of materials and other incidentals, as per approved specifictions drawing, design and as directed by the Engineer-Incharge. The rate inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing angle iron door,window,clerestory window frame manufactured from M.S.Angle iron section of 50x50x6 mm (Fifty into fifty into six millimetres) ,thickness including hinges jamb,lock jamb,beed and if required angle thrashold ofmild steel angle 50x25 mm (Fifty into twenty five millimetres) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (Two point five millimetres)thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-inCharge. complete in all respect as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals, and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing on wall face PVC (D-Plast) accessories for rain water pipe PVC Socket 150mm (One hundred fifty millmetres) 6kg/sqm working pressure clom B unplastisized PVC D-Plast on its equivalent high density pipe confirming to IS code 4985-2000 for main water pipe fixed with approved adhesive complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and fixing plain glass 4mm (Four millimetres) thick glass panes of Modi Gaurd/Saint Govin/Aashgi for shutter of opening with putty and nails and as per detail and HP PWD specifications including entire carriage of materials within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 19mm (Nineteen millimetres) thick water proof termit resistant commercial board of Kit ply /Centuary ply/Duraply/Marino ply for shelves and shutter all cut portions of the board shall have 6/12mm (Six/Twelve millimetres) thick hard wood edging to be finished with 1mm (One millimetres) thick lamination of Century/Green/Greenlam/Tesaply and approved shade with butt joints and fixing nails and screws etcetera; upto all floor level complete including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 19mm (Nineteen milimetres) thick water proof commercial board in shelves/box of Kitty/Centuary ply for cup board including its shelves and all cut portions of the board shall have 6mm (Six millimetres) thick hard wood edging with butt joints & fixing with nails & screws etc complete including entire carriage of materials within all leads, lifts and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 6mm (Six millimetres) thick ply wood lining of Kitty/Century ply with butt jointing (frame work and cover fillets to be measured and paid for separately) complete including entire carriage of materials within all leads, lifts and other incidentals,as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing door closer with necessary screws etcetera complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing cup-board shutter magnic catcher with necessary screws etcetera complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 65x35mm (Sixty five into Thirty five milimetres) size special quality chromium plated brass cup board lock with six leavers including necessary screws etcetera complete (Indian make) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing aluminium pilot sheet on equivalent double action hydraulic floor spring bright finished with nut & screws complete including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing aluminium pilot sheet on equivalent door stopper bright finished with nut & screws complete including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Fly wire mesh shutter using galvanised S.S. wire guage of I.S. Guage designation 85 G with wire of dia 0.56 mm (Zero point five six milimetres) for doors, windows and clearstorey windows including bright finished/black enamelled iron hinges with necessary screws complete including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 300x16mm (Three hundred into Sixteen milimetres) size aluminium Pilot/sheel sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing aluminium Tower bolts (Barrel type) anodized transparent or dyed to required colour and shade Pilot/sheel or equivalent with necessary screws etcetera complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

200x10mm (Two hundred into Ten millimetres) nominal size

150x10mm (One hundred fifty into Ten millimetres) nominal size

Providing and fixing aluminium Pilot oxidized seccuolar anodized transparent or dyed to required colour and shade handles with necessary screws etcetera complete including carriage of material within all leads, lifts and other. incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

125mm (One hundred twenty five millimetres) nominal size

100mm (One hundred millimetres) nominal size

75mm (Seventy five millimetres) nominal size

Providing and fixing 150mm (One hundred fifty millimetres) size aluminium Seccolar anodized transparent or dyed to required colour and shade with necessary screws etcetera; hooks and eyes complete including carriage of material within all leads, lifts and other. incidentals. as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

40mm (Forty milimetres) thick cement concrete flooring with angle iron 40 X 4 mm nosing thick cement concrete 1:2:4 (One cement: Two sand : Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size) and top layer of 15 mm (Fifteen millimetres) consisting of mix 1:2 (One cement hardner mix : Two stone aggregate 6 mm (Six millimetres) nominal size by volume including finishing complete including carriage of material within all leads, lifts and other. incidentals. as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 25mm (Twenty five millimetres) thick Kota Stone of uniform colour with 7.5cm (Seven point five centimetres) wide Jaislmer yellow/white marble brand of flooring (Mirror polished) of approved shade over base of flooring 20mm (Twenty millimetres) (Average) thickness cement mortar 1:4 (One cement : Four sand) laid over and jointed with Grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing/moulding an noising complete including carriage of material within all leads, lifts of material and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

15 mm (Fifteen millimetres) thick Cement plaster skirting (upto 30cm (Thirty centimetres) height) with cement mortar 1:3 (One cement : Three sand) finished with a floating coat of neat cement including rouding of junction with floor complete including carriage of material within all leads, lifts of material and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing IRC Jali in openable shutter 25 x25mm (Twenty five into twenty five millimetres) complete including carriage of material within all leads, lifts of material and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying Double charged vetrified tiles antiskid of Orient/ Somany/Rak/Nitco as per approved shade in flooring of size upto 600x600mm in flooring laid on a bed of 12mm (Twelve milimetres) thick cement mortar 1:3 (One cement : three sand) finished with flush pointing in white cement upto all floor levels complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying mirror polished kota stone slab 25mm (Twenty five millimetres) thick in risers of steps, skirting, dado and pillar laid on 12 mm (Twelve millimetres) (Average) thickness cement mortar 1:3 (One cement : Three sand) and jointed with Grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing and moulding complete including carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 20mm (Twenty milimetres) thick granite stone work required shade in flooring 20mm (Twenty milimetres) thick in cement mortar 1:3 (1 cement:3 sand) including jointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with an admixture of pigment to match the marble shade/epoxy complete including carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, moulding single or double as oer design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 300x600mm (Three hundred into six hundered millimetres) glazed tiles of Kajaria/NITCO/RAK/Asian in skirting and dado upto all heights with 12mm (Twelve milimetres) thick cement mortar 1:3(One cement :Three sand) jointing with cement slurry complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying heavy duty precast cement concrete 80mm (Eighty millimetres) thick precast paver blocks ISI marked of NTC IS No 15658 with vibro compacted upto M-50 (M-Fifteen) grade including border or kurb block grey or coloured laid over sub-base of concrete with 25mm (Twenty five millimetres) thick average thickness of cement mortar 1:4 (One cement : Four sand) and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing & polishing complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 0.60mm (Zero decimal Six Zero millimetres) thick prepainted steel sheet of TATA Durashine/Sail/Jindal ISI marked-2-1201 in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 10 (Ten) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (Six millimetres) diametres with prepainted limpet and rubber washers complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing ridges or hips laying propper Gola shape 60cm (Sixty centimeters) over all with 0.60mm (Zero point Sixty millimeters) thick prepainted sheet roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Tweny) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimeters) diametres with prepainted G.I. limpet and bitumen washers complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing valley 90cm (Ninety centimeters) over all with 0.60mm (Zero point Sixty millimeters) thick prepainted sheet roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 5 (Five) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimeters) diametres with prepainted G.I. limpet and bitumen washers complete with all accesoriees as required including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 30cm (Thirt centimeters) wide 90cm (Ninety centimeters) over all semi-circular 0.63mm (Zero decimal sixty three millimetres) thick of TATA plain G.I. sheet gutter with iron brackets 40x3mm (Forty into Three millimetres) size shall be provided with dome shade grating including bolts, nuts and washers etcetera and making necessary connections with rain water pipe complete including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved architectural drawing, design and as directed by the Engineer-in-charge complete. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing plain M.S. (mild steel) B.P. sheet 1.6 to 2mm (Two millimetres) thick fixed in eaves board/ceiling/cutting soffits/ceiling including jointing with gas/electric welding in position and applying a coat of red lead primer complete (frame work is to be measured and paid for separately) including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millmetres) dia pipes on wall face P.V.C (D-Plast) rain water pipes of 6 Kgs ( Six kilogram) ISI make of Finolex/Relpipe/Victous of working pressure not less than 4.5 kg/sqmm (Four point five kilograms per sqaure millimetres) high density pipe including filling the joints with approved adhesive complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing on wall face P.V.C. (D-plast) acessories for rain water pipes 6 kgs/sqm (Six kilograms per square millimetres) as per IS mark of Phenolex Relpipe (Reliance) victus working pressure class-B un plastisized PVC D-Plast high denesity pipe confiming to ISI Code 4545:2004 for rain water pipe fixed with approved adhesive including filling the joints complete including carriage of material within all leads, lifts and other. incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

150mm (One hundred fifty milimtres)diameteres PVC Plain bend

150mm (One hundred fifty milimtres)diameteres PVC Plain shoe

Providing and fixing M.S. holder bat clamps of approved design to H.D.P. rain water pipe embedded in and including cement concrete blocks 10x10x20cm of 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size and cost of cutting holes and making good the walls etcetera; complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 8mm (Eight milimetres) solid thick MS grills of required pattern in wooden frames of windows etc with M. S flat 20x5x8 mm (Twenty into Five into Eight milimetres), square or round bars in combination as per detail with round headed bolts and nuts or by screws complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Steel work welded in built up sections joints channels, angles, tees/tubler section/ frame work for roofing/ceiling/false ceiling flats with connection plates or angles, cleat as in trusses, trussed purlins main and cross beams, hips jack rafters, purlins connected to common rafters and the like any steel structure upto any height and in building including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paint i/c framed work with angle tees 40x6mm complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing anodised aluminium work for door frame, window, ventilators and glazed partitions frame and in shutters of door and windows with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etcetera. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P. brass/stainless steel screws. All complete as per architectural drawings and as per the directions of Engineer-In-Charge including carriage of materials within all leads and lifts and other incidentals.

Steel work welded in built up sections trusses and framed work in any section angle/channel or tubler, including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paint in gratings framed gaurds, bars, ladders, railing, brackets and similar work, complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing of hollow pipe of 50mm (Fifty millimetres) diametre hand rail slip resistant with round ended joint at two level at 75 and 90cm (Seventy and ninety centimetres) height welded with 25mm (Twent five millimetres) diametre M.S. hollow pipe which baluster embedded in cement concrete 60cm (Sixty centimetres) centre to centre and jointing with electrical gas welding at top alongwith hand rail of hollow M.S. pipe of 40mm (Forty millimetres) diametre. The baluster welded/jointed with each with 2 Nos M.S. flat of 50x5mm complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing anodised aluminium work for door, window, ventilators and glazed partitions shutter with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etcetera. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P. brass/stainless steel screws. All complete as per architectural drawings and as per the directions of Engineer-In-Charge including carriage of materials within all leads and lifts and other incidentals. including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing moulded hand rail of M.S. hollow pipe 50mm (Fifty millimetres) dia welded in straight lenght over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be mesaured & paid separete complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing 40x3 mm (Forty into three millimetres) flat iron hold fast 40 cm (Forty centimetres) long including fixing to frame with 10 mm ( Ten millimetres) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm (Thirty into ten into Fifteen centimetres) 1:3:6 (One cement : three sand : six crushed stone aggregate 20 mm (Twenty millimetres) nominal size) complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing throating or plaster drip and moulding to RCC Chajja complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Extra for making moulded nosing in terrazzo including returned moulded ends and angles to mouldings complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Painting two or more coats (excluding priming coat) with Nerolac/Asian paint on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Applying priming coat over new wood and wood based surfaces with Nerolac/ Asian paint after and including preparing the surfaces by thoroughly cleaning oil, grease, dirt and other foreign matters sand papering and knotting with ready mixed paint brushing wood primer pink including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Painting two or more coats (excluding priming coat) on over new wood and wood based surfaces with Nerolac/ Asian paint other than white brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters including carriage of material wthin all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

6mm (Six milimetres) thick cement plasters in ceiling with cement mortar 1:3 (One cement: Three sand) for all heights in all floor including carriage of material wthin all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

15mm (Fifteen millimetres) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior plastering including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement: Six sand) upto floor all levels including carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

15mm (Fifteen millimetres) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement: Six sand) above plinth level to floor all levels including carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

15mm (Fifteen millimetres) thick cement plasters in single coat on brick/concrete/stone walls for exterior plastering including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:5 (One cement: Five sand) above plinth level to floor all levels including carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Applying Birla J.K. white wall care putty over plaster surface after thoroughly brushing the surface free from mortar dropings, dust, loose material and other foreign matters, sand papered smooth to give final matt finish to the surface complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Distempering (two coats) with acrylic oli bound washable distemper with Dulux/Apex/Asian paint brand and manufactire and required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matters and also including preparing the surface even and sand papered smooth including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Painting two coats(excluding priming coat) on new concrete masonry/plaster surfaces with enamel paint of approved brand and manufacture to give an even shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth complete including entire carriage of material as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Wall painting (two or more coats) with acrylic washable emulsion paint of Asian Paint/Dulux/ Nerolac and manufacture on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing under layer for plinth protection of 75mm (Seventy five milimetres) thick(un-consolidated)bed of dry brick/stone aggregate 40mm (Forty milimertres) nominal sizes well rammed and consolidated and grouted with fine sand including preparation of ground complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing plinth protection 50mm (Fifty milimetres) thick cement concrete 1:3:6 (One cement: Three sand: Six graded crushed stone aggregate 20mm (Twenty milimetres) nominal size) including finishing the top surfaces of concrete smooth complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Construction of C.C. covered in cement concrete 1:3:6 (One cement : three sand : six graded crushed stone aggregate) including earth work shuttering and cast in-situ RCC slab over drain and cement concrete flooring 1:2:4 (One cement : two sand : four graded crushed stone aggregate) and finished with a floating cost of neat cement complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying concrete for plain/reinforced concrete 1:3:6 (One cement: three sand: Six graded broken/crushed stone aggregate 20mm(Twenty millimeters) nominal size in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 and 1203 PCC grade M-10 (M-ten) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing weep holes in brick masonry/stone masonry/plain reinforced concrete abutment, wing wall, return wall with 110mm diametres P.V.C. pipe extending through the full width of the structure with slope of 1(v):20(H) towards drawing face complete as per drawing and technical specifications Clause 614, 709, 1204.3.7 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Back filling with back filling behind Retaining wall/abutment, wing wall and return wall complete as per drawing & HPPWD Technical Specification Clause-1204.3.8 as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Polythyelene – Aluminium -Polyethylene (PE-AL-PE) composite pressure pipe Kitec /Kisan U.V. stabilized with carbon black Conforming to IS-15450-2004 for water supply including clamp at 1m (One metre) spacing, cutting, fixing and making good the wall etcetera but excluding the cost of fittings (internal work) pipes exposed on wall 1216 including filling the joints with approved adhesive complete as per specifications, approved drawing, design and including entire carriage of material within all leads lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

15mm (Fifteen millimetres) Outer diameters pipe

20mm (Twenty millimetres) Outer diameters pipe

Providing and fixing Polythyelene – Aluminium -Polyethylene (PE-AL-PE) composite pressure pipe Kitec /Kisan U.V. stabilized with carbon black Conforming to 1620 kitec composite fittings the joints with approved adhesive complete as per specifications, approved drawing, design and including entire carriage of material within all leads lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing & fixing Equal Tee of Kitec/Kisan

Providing & fixing Equal Elbow Kitec/Kisan

Providing & fixing Female Tee Kitec/Kisan

Providing & fixing Female Elbow Kitec/Kisan

Providing & fixing Male Thread Socket Kitec/Kisan

Providing & fixing Female Thread Socket Kitec/Kisan

Providing & fixing Female Connector

Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20mm to 40nmm (Twenty millimetres to Forty millimetres)nominal bore by providing and fixing tees including cutting and threading the pipe complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing in trenches P.V.C. pipe of Supreme/ Kishan/Finolex/Relpipeincluding pressure 6Kg/mm(Six kilogram per millimetres) spigot socket waste ventilatiing pipe including fixing with adhesive mixure complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

110mm (One hundred ten millimetres) nominal bore/diametres

75mm (Seventy five millimetres) nominal bore/diametres

Providing and fixing sand cast/cast iron M.S. holder bat clamps including steel bolts to sand cast/spun iron pipes embedded in and including cement concrete block 100x100x100cm (One hundred into one hundred into one hundred centimetres) of 1:2:4 (One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size and cost of cutting holes and making good the walls etcetera; complete as per specifications and as directed by the Engineer-In-charge, including entire carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

110mm (One hundred ten millimetres) nominal bore/diametres

75mm (Seventy five millimetres) nominal bore/diametres

Providing and fixing P.V.C. Supreme/ Kisan/Astral or equivalent plain bend accessirues for sewerage pipe confirm to IS No. 14735-99 including fixing with approved adhesive complete, including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

110mm (One hundred ten millimetres) nominal bore/diametres

75mm (Seventy five millimetres) nominal bore/diametres

Providing and fixing P.V.C. tee medium class of Supreme/ Kisan/ confirming to IS No-14735-99 including fixing with approved adhesive complete, including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

110mm (One hundred one milimetres) diametres

75mm (Seventy five milimetres) diametres

Providing and fixing P.V.C. Supreme/ Kisan Collar ISI marked confirming to IS No-14735-99 including fixing with approved adhesive complete, including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

110mm (One hundred one milimetres) diametres

75mm (Seventy five milimetres) diametres

Providing and fixing P.V.C. Supreme/Kisan cowl ISI marked including fixing with approved adhesive complete, including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

110mm (One hundred one milimetres) diametres

75mm (Seventy five milimetres) diametres

Providing and fixing P.V.C. Supreme/Kisan cowl ISI marked including fixing with approved adhesive complete, including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing PVC Door Tee 110mm (One hundred one milimetres) diametres

Providing and fixing PVC Plain Tee 110mm (One hundred one milimetres) diametres

Providing and fixing PVC Long bend 40mm x 1.00 mtr. (Forty milimetres into one metres) diametres

Providing and fixing PVC Elbow 40mm (Forty milimetres) diametres

Providing and fixing 110x90mm (One hundred ten into nineteen millimetres) nominal size/diameter P.V.C. floor trap Supreme/ Kisan ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etc complete, including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Orissa pan-20090 of Hindware/Cera/Jaquar of star white/Snow white shade with size 53x41cm (Fifty three into forty one centimetres) (earth work, bed concrete, foot rest and trap to be measured and paid for separately) including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing EWC vitreous china of Star No-20087 (S-10) of size 57x35x39cm (Fifty seven into Thirty five into Thirty nine centimetres) fixed to PVC cistren (Sleek plug) fixed to jet pressure of Hindware/Cera/Jaquar of star white/Snow white shade including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 10.00 Ltrs (Ten litres) capacity PVC low level dual flushing cistern ISI marked as Cera/Jaguar/Hindware with a pair of C.I. or M.S. brackets with fittings such as lead valve less siphon, 15mm (Fifteen milimetres) nominal size brass ball valve with polythene float, C.P. brass handles, unions and couplings for connection with inlet, outlet and over flow pipe, 40mm (Forty milimetres) diametres C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for separately) within all leads, lifts of materials and other incidentals

Providing and fixing 100mm (One hundred millimetres) nominal bore sand cast iron P or S traps for water closet (squatting pan) including jointing the trap with pan and soil pipe in cement mortar 1:1 (One cement : One sand) including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing plastic seat solid type and cover for wash down water closet with C.P. brass hinges and rubber buffers matching with shade of European W.C. pan including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing vitreous china wash basin gariet No-10080 Cera / Hindware Jaguar/Snow white/star white shde 58x40x80cm (Fifty eight into forty into eighty centimetres) under counter basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same with pedestal but excluding fittings including neccessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 161.4x54cm (One hundred sixty one point four into Fifty four centimetres) depth of 200mm (Tweo hundred millimetres) stainless steel kitchen sink with drain of AMC/Unik/Diamond with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same but excluding the cost of fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing vitreous china pedestal Cera or equivalent of approved shade for wash basin comnplete at the back for the resption of pipe and fittings complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) nominal size diametres rubber plug for wash basin including entire carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) diametres M.I. union for wash basin and sink complete in all respect including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) diametres PVC waste pipe for wash basin or sink including check nut complete, including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetres) diametres C.P. Grating of ISI marked of Kingston/CPM/Jal/ESS/Jaguarfor gully floor or Nahni trap including entire carriage of material within all leads, lifts and other incidental as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing flat back 600x450mm (Six hundred into Four hundred fifty millimetres) beveled edge mirror of ATUL/MODI of superior glass mounted on 6mm (Six millimetres) thick A.C. sheet or ply wood sheet and fixed to plugs with C.P. brass screws and washers including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x20mm (Six hundred into Twenty millimetres) C.P. brass Towel rail ISI marked Kingston/Gem/Parko/Jaguar complete with C.P. brass brackets fixed to plugs with C.P. brass screws etcetera including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x120mm (Six hundred into One hundred twenty millimetres) glass shelf with C.P. brass of ISI marked of approved brand (Heavy duty) with brackets and guard rail complete fixed to wooden plugs with C.P. brass fitting with neccessary screws including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing C.P. brass toilet paper holder of (Heavy duty make ISI marked of approved brand including neccessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing chromium plated jet pressure of Kingston/Gem/Jaquar including fitting complete including entire carriage of material within all leads lifts and other incidentals and as per specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore chromium plated PTMT push cock tap of ISI marked of Kingston/Gem/ESS/Jaquar complete as per specifications including entire carriage of material within all leads lifts and other incidentals, and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore chromium plated fancy bib tap of ISI marked of Kingston/Gem/ESS/Jal/Jaquar complete as per specifications including entire carriage of material within all leads lifts and other incidentals, and per as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) diametre C.P. brass stop cock IS marked of Kingston/Gem/ESS/Jal/Jaquar as per specifications including entire carriage of material within all leads lifts and other incidentals and per as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) diametres C.P. brass pillar tap with capstan head IS marked of Jal/ESS ESS/Kingston/Gem including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) diametres brass angle valve without nuts IS marked Kingston/Gem/ESS/Jal/Jaquar as per specifications including entire carriage of material within all leads lifts and other incidentals, and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing C.P. brass full way valve with wheel ISI marked of Kingston/Gem/ESS/ Jal/ Jaquar as per specifications including entire carriage of material within all leads lifts and other incidentals, and per as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

15mm (Fifteen millimetres) nominal bore/ diametres

20mm (Twenty millimetres) nominal bore/ diametres

Providing and fixing 15mm (Fifteen millimetres) nominal bore C.P. brass valve (Horizontal plunger type) high pressure with copper plate as per specifications including entire carriage of material within all leads lifts and other incidentals, and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore PVC connection pipe with brass union 45cm (Forty five Centimetres) length complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing P.V.C. SINTEX water storage tank (Tripple layers) having capacity of 1000 (One thousand) liters of ISI 12701 marked with G.I. (Galvanised iron) inlet and outlet connection, 15mm (Fifteen millimetres) nominal bore ball valve and mosquito proof P.V.C. cover with locking arrangment including hoisting upto all heights above ground level as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing to level or slopes PVC pipe for sewerage line and jointing with approved adhesive complete as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (One cement : Five sand : Ten graded crushed stone aggregate 40mm (Forty milimetres) nominal size) bedding for PVC pipe of the 250mm (Two hundred fifty milimetres) internal diametres including testing of pipes and joints complete as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Construction of manhole with R.C.C. top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty millimetres nominal size) foundation concrete 1:4:8(One cement: Four sand: Eight graded crushed/broken stone aggregate 40mm (Forty millimetres nominal size) inside plastering 15mm (Fifteen millimetres) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty millimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred millimetres) 500mm(Five hundred millimetres) deep, including precast cement concrete cover (medium duty) with 300mm (Three hundred millimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Construction of manhole with R.C.C. top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty millimetres nominal size) foundation concrete 1:4:8(One cement: Four sand: Eight graded crushed/broken stone aggregate 40mm(Forty millimetres nominal size) inside plastering 15mm ( Fifteen millimetres) thick with cement mortar 1:3 ( One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty millimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred millimetres) 1.00 mtrs(One metre) deep, including precast cement concrete cover (medium duty) with 300mm (Three hundred millimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Saravjeet

ATUL RANA GOVT CONTRACTOR