GE I R AND D/CHD-99/2024-25 PROVISION OF FIRE ESCAPE FOR MAIN OFFICE BLDG AND RAIN PROTECTION SHED AT MAIN GATE OF TBRL SECTOR-30 CHANDIGARH AND DEVELOPMENT OF CENTRALIZED EXHIBITION/DISPLAY CENTER AND PROVISION OF COVERED SHED FOR PATHWAY FROM MANTH

Amount

Material and labour for stair case (framed work) including stringers, treades, landing, balusters, hand rails, vertical post etc including cleats, brackets, Fe 410 -W (Gde-E- 250) quality-A etc. complete all as specified and directed .

Material and labour for preparation of new previously untreated steel surfaces of any despcription, over 10 cm width or girth, otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer two coats of synthetic enamel paint including preparation on steel surfaces of any description over 10 cm width or girth complete all as specified and directed.

Demolition of cement concrete as in ground floors and pavings n.exc 15cm thickness, below or above ground level complete all as specified and directed

Material and labour for excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in soft/loose soil complete all as specified and directed

Material and labour for PCC (1:2:4) type B2 (using 20 mm graded stone aggregate) for fdn/ mass concrete & post holes etc, complete all as specified and directed

Cutting holes into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required exc 400 sqcm but n exc 0.10 sqcm complete all as specified and directed

Material and labour for cutting opening in cement concrete walls where reinforcement is cut through (any description) for door, window and other openings (with or without reveals) or enlarging existing openings, including trimming surfaces to receive rendering, etc. with or without reinforcement complete all as specified and directed.

Supply and fixing for steel work in trusses, purlins, posts and the like using tubular/ square hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes/SHS conforming I.S.1161-2014/IS 4923-1977 grade St-240 complete all as specified and directed

Material and labour for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50m thick of an colour having tensile strength of 550 mpa as in roof covering fixed with self-tapping screws/J hooks complete all as specified and directed.

Supply and fixing for rolled mild plates (Base plate, gusset plate) (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without and attachment of grade Fe 410-W (Gde E-250) quality hooks complete all as specified and directed.

Supply and fixing for mild steel bolts, purpose made with hexagonal or square head one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut. Length of bolt 100 m, dia - 16 mm complete all as specified and directed.

Material and labour for fabrication and fixing in repair of anodised aluminium door shutter fixed with rubber gasket, stopper, cleats, handles etc complete for aluminium frame of size 101.6mm x 44.45mm x 2mm and section of bottom and top rail of section114mmx44.45mmx2mm thick and lock rail shutter frame of 83mm x 44.45mm x 2 mm with and including panels of 5.5 mm thick plain/frosted float glass, and with anodised aluminium snap beading of size 18.2mmx16.66mm screed for fixing fully including double action door spring hydraulically regulated made up of 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and all necessary fitting sand EPDM rubber packing each shutter shall be provided with two decorative type aluminium disc handle of 150 mm dia per shutter ,1 no heavy duty door shutter 1no 200mm long aluminium tower bolt per shutter including complete all as specified and directed

Supply and fixing for door closer (aluminium die cast body) hydraulically regulated, designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

Demolition of brick work built in cement mortar of any description complete all as specified and directed.

Material and labour for brickwork with sub class B bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 by using old size bricks complete all as specified and directed .

Material and labour for 15 mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm & 5 mm) mixed with water proofing compound in top layer 200 ml per beg of cement or as per manufacturer's instructions finishing the surface fair and even without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and directed

Material and labour for preparing new plastered surfaces of walls and finishing the walls with Acrylic smooth exterior paint of required shade: New work (Two or more coats applied @1.67 Ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 Kg/ 10 sqm). complete all as specified and directed .

Material and labour for 3 mm thick aluminium composite panel roof/ cladding work of choice colour including necessary bracing for fixing to frame work or wall/ roof surface etc. by means of riveting complete all as specified and directed ..

Excavation in post holes (or similar holes) each n,exc 0.5 cum, getting out from hard and dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

Supply and fixing for roof trusses (framed) trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle channel or flat sections) including distance pieces, cleats etc conforming to Fe - 410-W (Gde- E-250) quality-A complete all as specified and directed.

Supply and fixing for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction nutt welded tubes as in post confirming to Fe-410W (gde E-250 quality A) complete all as specified and directed.

Supply and fixing for precolor coated high tensile steel galvalume sheet with eaves pattern in single piece of suitable length convex shaped (crimpling edges) at end as per site requirement in footing with yield strength (550mpa) pre-painted with aluminium (55%) and zinc (45%) alloy coating applied through continuous hot dip process having total coated thickness (TCT) of 0.50 mm and total coating thickness on each side 0.025 mm with minimum coating mass on both sides @ 150 gram/sqm, in length and width as per site requirement fixed with compatible accessories as per manufacturers instructions as per the profile and shade/colour complete all as specified and directed.

Supply and fixing for pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in wall, fixed with self-tapping screws complete all as specified and directed.

Supply and fixing for hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Providing and fixing frech door EN01 EN 62 casement Cmnt F 5000Wx2500h (m) (134.55 Sqft) 8 mm toughened glass dimension type- Frame size from RO, Reinforcement - full size, coextruded bead -No, Profile shape-none , Colour -Foil 2S , Foils2S- Dark Gray, Fame extension -None, Coupling 180 -PAUC001, Window O/F- 62 mm/P62F002+1mm , Threshold -No frame, French Mullion- PAUC006+1mm , door Z shash-110mm/P62SD02=1.5mm, Bead shape -Default, Fittings supplier-filtting supplier1, Hinge color-Black, Handle colour-Black, Door handle- Locking A , Door Hinge Type -Flag/3D Hinges, Door backset-35 mm, Door slave lock-shoot bolt, Espag material-SS, Supply type- supply & install, Silicon sealant- 280 mm bottle, Display fixings -No, Wind load-No complete all as specified and directed.

Material and labour for 12 mm thickness preprinted perforated particle board/tiles for insulation and acoustic purposes, 60x60 cm in size, fixed with nails frame work of any description or with staples on snap grid. complete all as specified and directed.

Supply and fixing for anodised aluminium snap grid (Size of grid 605 x 605mm) frame work for false ceiling all as specified with and including Hangers 4 mm dia. G.I flat 40 x 3 mm size 60mm long complete all as specified and directed.

Supply and fixing for anodised aluminium frame for partition wall with one or more rebates incl joining cleat aluminium beading, rubber packing incl fixing bolt, design and pattern complete all as specified and directed.

Supply and fixing for 10 mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft /loose soil complete all as specified and directed.

Material and labour for cement concrete type B2 1:2:4 (40 mm graded aggregate) in foundations, filling and mass concrete complete all as specified and directed

Supply and fixing for roof trusses (framed) Fe 410 -W(gde-E- 250) quality A, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed

Material and labour for preparation of new previously untreated steel surfaces of any description, over 10 cm width or girth, otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Supply and fixing for precolor coated high tensile steel crimp curved galvalume roof sheet requirement in roofing with yield strength (550mpa) pre-painted with aluminium (55%) and zinc (45%) alloy coating applied through continuous hot dip process having total coated thickness (TCT) of 0.50 mm and total coating thickness on each side 0.025 mm with minimum coating mass on both sides @ 150 gram/sqm, in length and width as per site requirement fixed with compatible accessories as per manufacturers instructions as per the profile and shade/colour as approved complete all as specified and directed.

L-7 Primewave Communications (BID ID -3365820)

SS BUILDERS (BID ID -3360710)

KUKREJA ENGINEERS (BID ID -3366495)