Construction of Assistant Engineer Office-cum-Residence at Haripurdhar Tehsil Sangrah District Sirmour H.P.

Amount

Excavation in foundation,trenches etc. in earth work in all heights and depths in all kinds of soil, including saturated soil comprising of pick work,jumper work and blasting work both in soft and hard rock with chiselling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soil including dewatering where ever required,setting out to required lines,levels as shown on the drawings and as directed by the Engineer-in-Charge at site, according to the HPPWD specification of 1990-Volume-I, and shorting out useful and un-useful materials and stacking the same in all leads,lifts and trensportations of the usefull materials for filling in roadways embankments for grades improvements and levelling to required grades and then disposing of surplus excavated earth in acquired width of road on or approved dumping sites through all modes of transpsportation including head load animal load or mechanical means alongwith its levelling fine dressing and all labour, mechnieries materials,tools,equipments and incidental necessary to complete the work by mechanized means and labouor(if any required).All useful materials such as stone single, aggregate and slates shall be sorted out and stacked along road side to the maximuim possible extends in all leads,lifts through all modes of transportation and all others incidental charges any loss to the public and private properities during the course of execution and disposal of serviceable and un-serviceable materials shall be the absolute responsibility of the contractors and shall have to be duly compensated by him in all respect.

Filling in plinth with course sand under floor inclduding watering ramming consolidating and dressing complete. as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing form work in steel plates 3.15mm (Three point fifteen milimetre)thick welded with angle iron in frmae 30*30*5mm (Thirty into thirty into five). So as to give a fair finish including strutting and propping etc, with wooden battens and ballies heights of propping and centering below supporting floor to ceiling not exceeding 4 (Four metre) and removal of the same for insitu- reinforced concrete & plain concrete work. as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Foundation footing bases of columns etc and mass concrete including plinth beams and columns upto plinth levels.

In flat surfaces such as soffits of suspended floors,roofs, landings and the like. Floors etc. upto 200 mm ( Two hundred milimetre) in thickness.

Columns pillars and posts struts square rectangular polygonal in plain.

Beams, cantilevers, girders and lintels, sides and soffits of Beams, beam haunchings, cantilevers, girders, bressumers and lintels not exceeding 1 meter (One meter)in depth in all heights from floor.

Stair case with sloping or stepped soffits excluding landing complete.

Edges of slab and breaks in floors and walls. Upto 20cm (Twenty centemetre) wide.

Providing and laying cement concrete 1:4:8 ( One cement:Four sand: Eight graded tone aggregate 40mm nominal size) and curing complete excluding the cost of form work in foundaion and plinth.as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and laying damp proof courses 38mm (Thirty eight milimetre) thick with cement concrete 1:2:4 (One cement:Two sand :four graded ,crushed stone aggregate 20mm ( Twenty milimetre) nominal size) mechanically mixed, vibrated and curing complete., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Applying a coat of hot bitumen( mexphalt 80/100 (eight oblic one hundred) equivalent using 1.70kg (One point seven zero kilogramme) per square metre proof courses after cleaning the surface with a pieceof cloth lightly soaked with kerosene., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and laying cement concrete 1:1.5:3 (One cement:One & half sand:three graded/crushed hard stone aggreagte 20mm(Twenty milimetre) nominal size)mechanically mixed,vibrated and curing complete to obtain the minimum crushing strength of M-15(M-Fifteen)grade. as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

(a) Foundation footings and bases of columns etc. and mass concrete

Suspended floor,roofs,landing shelves and their supports balconies,beams,girders,bressumers and cantilivers Upto floor two level

Columns, Pillars, Posts and struts.Square, rectangular or polygonal in plan Up to floor all level

Stair cases( Except spiral stair case) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

Providing tor steel reinforcement for reinforced cement concrete work including bending,binding and placing in position including cost of binding wire complete.., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Randum rubble masonry/polygonal rubble masonry ( Uncoursed brought to courses) with hard stone of approve quality in foundation and plinth including levelling up with cement concrete 1:6:12 ( One cement:Six sand:Twelve graded stone aggregate 20mm nominal size) at plinth level in cement mortor 1:6 ( One cement:Six sand)as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

2nd( Second)class brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:6(one cement:six sand)., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

2nd( Second)class brick work using common burnt clay building bricks in superstructur above floor two level in Cement mortor 1:6 ( One cement:six sand) , as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

2nd ( Second)class Half brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:4(one cement:four sand)., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing wood work in frames of doors, wondowas clearsory, windows and other frames wrought, framed and fixing in position 2nd class deodar wood.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing panelled glazed of panelled and glazed shutters for doors windows and clerestory windows including black enamelled iron butt hinges with necessary screws complete 40mm (forty milimetre) thick second class deodar wood as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey wondows including bright finished black enamelled iron hinges with necessary screws complete, 40mm(forty milimetre)thick 2nd class deodar wood as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and fixing 19mm ( Nineteen milimetre) thick commercial board water proof shutters for cup board including fixing with nickel plated piano withscrews etc. complete.as per HPPWD specification 1990-Volume-I,including carriage of all labour,equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges.

Providing and fixing 25mm(Twenty five milimetre) thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nail & screws etc. complete)as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing 12mm(Twelve milimetre) thick 150mm (One hundred fifty milimetre) wide palement with 25mm(Twenty five milimetre) diametre wooden curtain rods and brackets including fixing 25x3mm ( Twenty five into three milimetre) M.S, flate at 10cm long and plugs etc, complete. Ist class deodar wood.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing 40x3mm ( Forty into three milimetre) flat iron hold fast 40cm ( forty Centremetre) long including fixing to frame with 10mm ( Ten milimetre) diametre bolts and nuts and wooden plugs and embedding in cement concrete block 30x10x15cm ( thirty into ten into fifteen centimetre) 1:3:6 ( One cement:three Sand: six graded stone aggregate 20mm ( Twenty milimetre nominal size),as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer in charge.

Providing and fixing aniodized aluminium sliding doors bolts anodized colour and shade with bolts and nuts screws etc.complete 250X16mm(two hundred fifty into sixteen millimetre).as per HPPWD specification 1990-Volume-I,including carriage of all labour,equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges.

300x16mm(three hundred hundred into sixteen millimetre)

250X16mm(two hundred fifty into sixteen millimetre)

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with necessary screws etc, complete.as per HPPWD specification 1990-Volume-I,including carriage of all labour,equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges.

300X10mm(three hundred into ten millimetre)

250X10mm(two hundred fifty into ten millimetre)

Providing and fixing alumimium handles anodized transparent or dyed to required colour of shade with necessary screws complete.as per HPPWD specification 1990-Volume-I,including carriage of all labour,equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges.

125mm (one hundred twenty five millimetre)

Providing and fixing M.S. hydraulic door closer.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing 100mm (One hundred milimetre) bright finished brass foor door stopper with rubble cushiion screw etc. to suit shutter thickness completeas per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing bright finisged hard down Hooks and eyes 200mm dia ( Two hundred milimetre dia) as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Proiding an fixing choromium plated brass 100mm (One hundred milimetre) latch and lock and pair of knob with necessary screws etc. completeas per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing M.S. grills of required pattern in wooden frames of windows etc. With M.S. flats ,square or round bars with round handed bolts and nuts or by secrews Plain grill as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing 75x60mm (Seventy five into Sixty milimetre) rounded hand rail in staight complete using second class deodar wood., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Kota stone slab flooring 20mm (Averagge) thick base of cement mortor 1:4 ( One cement:four sand) aide over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Precast terrazo tiles hydraulic copressed medium shade 20mm (Twenty milimetre) thick with marble chils of specified size ;laid in floors treads of steps and landings on a bed of 25mm ( Twenty five milimetre) average thickness of cement mortar 1:6 ( One cement:six sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles(whereever required) including rubbing and polishing complete,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and laying 30x30 cm Thirty into thirty ilimetre)spartic ceramic tile 5.5mm (Five into five ilimetre) matt finished of approved shade of scrany/Nitco on a bed of 12mm tick cement mortor 1:3 ( One cement:Three sand) with flush pointing in white cement.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and laying Baroda Green marble work having semi round nosing over 62mm thick RCC shelf.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Precast terrazo tile with nosing in stai case.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Precast terrazzo tile hydraulic compressed 20mm thick ( with marble chips of specified size) in skirting and riser of steps not exceeding 30cm in height on 10mm thick cement plaster 1:3 ( One cement:three sand) jointed with neat cement slury mixed with pigment to match the shade of tile (Whereever) required) including rubbing and polishing complete with white tiles as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

White Glazed tiles 6mm thick in skirting risers of steps and dedo on 12mm thick Cement Mortar 1:3 ( One Cement : Three sand) and jointed with cement slurry as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing 0.60mm thick prepainted galvanised steel sheet roofing with hot dipped metalic zinc coated sheet with top coat of reqular modified polyster (RNP) organic coating of 20(Twenty) micron over 5 (Five) micron priming coating to back coat of polyster of 5 (Five)micron over 5(Five) micron of priming coating including fixing withh prepainted iron J or L hooks, bolts nuts 6mm dia with prepainted limpet and rubber wahers complete with all accessories as requiredas per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing riddges or hips 50cm overall wiht 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheet with top coat of reqular modified polyster organic coating of 20 micron over 5 micron priming coating + back coat of polyster of 5 micron over 5 micron of priming coating including fixing with prepainted iron J or L hooks, bolts &^ nuts 6mm dia & prepainted G.I. limpet & bitumen washers complete wit all accessories as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing valley 60cm overall 0.60cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped etalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 micron over 5 microns primer coating includingh fixing with prepainted iron J or L hooks , bolts and nuts 6mm dia with prepainteted G.I. limpet and bitumen washers complete with all accessories as required as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Provididng and fixing 45cm wide and 40cm deep semicircular plain galvanised sheet gutter and nuts with washers connecting with rain water pipe in proper (frame work to be measured & paid for seperately)as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing black sheet facia/sofit 2mm ( Two milimetre) thick and 20cm ( Twenty centiletre) wide welded with angle iron frame 40 x 40 x 6mm ( Forty into Forty into Six Milimetre) and vertical support of M.S. flat 40 x 6 (Forty into Six Milimetre) fixing in position including a priming a red lead paint as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing MS B.P sheet 1.66mm to cmm thick in eaves board/ facia/ soffits/ ceiling including cutting, fxing and welding to steel, roof members and applying a coat of red lead primer competeas per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing wind tiles of mild steel flat 4x6mm size fixing in position complete as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing on wall face PVC (D-Plast)100mm dia pipe. Accessiories Rain water pipeof working pressure not 4.5 kg less than 4.5kg sqm including filling the joints with approved adhesives complete as per HPPWD specification 1990-Volume-I,including carriage of all labour,equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges.

Providing and fixing on wall face PVC (D-Plast). Accessiories Rain water pipeof working pressure not 4.5 kg less than 4.5kg sqm including filling the joints with approved adhesives complete as per HPPWD specification 1990-Volume-I,including carriage of all labour,equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges.

PVC bend 150mm diametre

PVC shoe 150mm dia

Providing and fixing MS holder bat clamps of approved design to C.I or SCI pipes embeded in and including cement concrete blocks 10x10x10cm of 1:2:4 ( One cement:Two sand:Four graded stone aggregate 20mm nominal size) and cost of cutting holes and making good the wall etc. 150mm diametre for C.I. pipes.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing M.S. fan clamps type-I of 16mm dia M.S. bar bent to shape with nooked ends in RRC slab during laying including painting the exposed portion of 100 pices as per standard dsign.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing in position collesible steel shutter with vertical channels 20mmx10mmx2mm and braced with flat iron diagonals 20mmx5mm size with top and bottom rails of T. iron 40mmx40mmx6mm with 38mm dia steel pulley complete with bolts and nuts locking arrangements stoppers handles, incluing applying a priming coat of red lead paint.,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Steel work in single sections including cutting, hoisting,fixing in position and applying a priming coat of red lead paints in RS Joist, channels angles tees.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing molded hand rail f M.S. hollow pipe 50mm dia welded nin straight length over M.S. flat at top of vertical balusters including one coat of red oxide priing coat complete ( M.S. flat & balusters of railing shall be measured & paid for seperately.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Steel work welded in built up sections, trusses and framed work, including cutting,hoisting,fixing in position and applying a priming coat of red lead paint ., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

In trusses and trusssed pulines in buildings

Provididng and fixing M.S. 100mm dia for support in porch as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease, dirt and other foreign matter,sand papering and knotting Readymixed paint brushing wood primer pink ., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Painting two coats (excluding priming coat)on new wood and wood based surface with enamel paints to give an even shade including cleaning the surface of all dirt,dust and other foreign matter,sand papering and stopping with white enamel paint other than white .as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Painting two coats ( excluding priming coat on new steel and other metal surface with enamel paint brushing to give an even shade including cleaning th surface of all dirt,dust and other foreign matter with namel paints other than white.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

6mm ( Six milimetre plaster to ceiling in cement mortor 1:4 ( One cement: three sand., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

15mm(fifteen millimetre) plaster in signle coat on fair side of brick/stone/ concrete walls for interior plastering upto floor two level including arrises, internalrounded angles, chamfers and/or rounded angle not exceeding 80mm(Eighty millimetre) in girth and finished even and smooth cement mortar 1:6 (One cement six sand.., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

15mm(fifteen millimetre) plaster in signle coat on rough side of brick/stone/ concrete walls for interior plastering upto floor two level including arrises, internalrounded angles, chamfers and/or rounded angle not exceeding 80mm(Eighty millimetre) in girth and finished even and smooth cement mortar 1:6 (One cement six sand)upto all floor level., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Applying priming coat on new concrete/masonry/ asbestos cement/ plastered surface after and including preparing the surface by throoughly cleaning oil, grease,dirt and other foreign matter and sand papering as required with readymixed primer., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Finishing wall with weather proof exterior grade emulsion of approved design ( Apexultima) ir its equirlied on undecorated wall surfaces ( Two coats) to give an even shade and final finish after through cleaning the surface to remove all dirt,dust and other foreign matter etc. including sand paper smooth complete.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Distempering( One coat) with oil bound washable distemper if approved brand and manufacture and of required shade on decorated wall surface to give an even shade after thoroughly brushing the surface clean of all grease, dirt,loose pieces of scales and also inclcuding preparing the surface even and sand papered smooth.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

White washing with lime on decorated wall surfaces ( One coat) to give an ven shade including thoroughly brooming the surface to remove all dirt,dust, mortor drops and loose of lime wash and other foreign matter.as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing plint protection 50mm ( Fifty milimetre) thick in cement concrete 1:3:6 ( One cement:Three sand:Six graded crushed stone aggregate 20mm (Twenty milimetre)niminal size., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing under layer for plinth protection of 75mm (Seventy five millimetre) thick (unconsolidated)bed dry brick/stone aggregated 40mm (Forty millimetre) nominal size will rammed and consolidated and grouted with fine sand including preparation of ground., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

construction course rubble hammer dressed "U" shape opened surface drain with side wall 15x22cm ( fifteen into twenty two centemetre) in cement mortar 1:6 ( One cement:Six sand) and inside plaster in cement mortar 1:3 ( One cement:Three sand) including earht work and laying 10cm (Ten centemetre) cement concrete 1:5:10 ( One cement:Five sand:ten graded stone aggregate 40mm (forty milimetre) nominal size and 7.5 cm ( Seven point five centemetre) cement concrete 1:2:4 ( One cement;Two sand:four graded/crushed stone aggregate 20mm (Twenty mlimetre) nominal size and finished with a floating coat of neat cement complete as per standard design, as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and fixing to wall, ceiling and floor galvanised mild steel tubes (medium grade) ISI marked tube fitting and clamps including making good the wall, ceiling and floor ., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

15 mm ( Fifteen milimetre) nominal bore .

20 mm ( Twenty milimetre) nominal bore .

Providing and laying in trenches 20mm (Twenty milimetre) nominal bore galvanised mild steel tubes ISI marked ( medium grade) tube fitting., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Making connection of galavanised mild steel distribution branches with galvanised mild steel tube 20mm ( Twenty milimetre) to 40mm (forty milimetre) nominal bore by providing and fixing Tee including cutting and treading the pipe complete., as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and fixing PVC water storage tank of ISI : 12701 marked,G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level :- 1000 litres net capacity tank, as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and fixing P.V.C. soil waste and ventilating ( D- plasting pipe of working pressure not less than 4.50kg/ sqm (four point fifty kilogramme per square metre including fitting the joints with adhesive complete ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer in charge.

100mm ( One hundred milimetre) niminal size

150mm ( One hundred fifty milimetre) niminal size

Providing and fixing sand caste/iron spun spigot and sockets soil waste and ventilating pipes jointed properly complete.,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

100mm ( One hundred milimetre) niminal size

150mm ( One hundred fifty milimetre) niminal size

Providing and fixing sands cast iron/cast iron spun fittings and accessories bend of required degree (any radius).as per HPPWD specification 1990-Volume-I,including carriage of all labour,equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges. Plain bends

100mm (One hundred millimetrer) nominal size.

Suppliying cast iron cover without frame for manholes:For frame of 500mm internal diametar C.I. cover (medium duty) the weight of cover to be not less than 58kg. ,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 and water tight C. I . cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53kg and frame to be not less than 2.72kg. ,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

150mmx100mm size P or Rtype

Providing and fixing cast iron holder bats including steel bolts to sand cast iron/ Caste(Spun) iron pipes embeded in and including cement concrete blocks 100X100X100mm(One hundred into One hundred into One hundred millimetrre) of cement concrete 1:2:4(:One cement:two sand:four graded stone aggregate) 20mm nominal size) including cost of cutting holes and making good the walls.as per HPPWD specification 1990-Volume-I,including carriage of all labour,equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges.

100mm (One hundred) millimetrer) nominal size.

150 mm (One hundred fifty millimetrer) nominal size.

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete.as per HPPWD specification 1990-Volume-I,including carriage of all labour,equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges.

110mm (One hundred ten millimetrer) nominal size.

Providing and fixing PVC bend single equal branch plain ISI marked including fixing with approved adhesive etc. complete.,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

110mm (One hundred ten millimetrer) nominal size.

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS-15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only).,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Equal Tees.1216 .

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete.,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

150 mm dia.

110 mm dia.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting and making good the wall and floor etc. complete.,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

110mm x 90mm

Providing and fixing vitreous China wash down,water closet squatting pan orrisa pattern (Indian type W.C pan) size 580mm (Earth work, bed concrete, foot rest and trap to be measured and paid for separatees.,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing viterous china water closet squating pan Europion type W.C Pan) size 580mm(Five hundred eighty milimetre) earth work, bed concrete, foot rest and trap to be measured and paid for seperately.Angle Angle Indian Universal closet ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer in charge.

Providing and fixing vitreous China100 mm size 'P' or 'S' trap for water closet ( squatting pan)including jointing the trap with the pan and soil pipe in cement mortar 1:1(1 cement : 1 sand) ,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

550mmx400mm

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting.,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

610 x460 mm with boul depth 200 mm.

Providing and fixing Viterous china automatic flushing cistern with a pair of C.I. Or M.S. brackets complete with fittings including C.I. Syphonic apparatus, mosquito proof lid, C.P. Brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately),as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing rubber plug for sink / wash basin ,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

32mm dia

Providing and fixing C.P. Brass waste for wash basin or sink .,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

32mm dia

Providing and fixing 100mm sand cast iron grating for gully, floor or Nahni trap. ,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing C.P. Brass Towell rail coplete with C.P. Brass brackets fixed to wooden pluges with C.P. Brass screws ,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

600mm x 20mmm

(i) Providing and fixing 600mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden pluges with C.P. Brass screws. ,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing charomium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws ,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing C.P Brass Toilet paper holder,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing C.P Brass bib tap with Capstan head,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

15mm dia

Providing and fixing C.P Brass pillar tap with Capstan head,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

15mm dia

Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous China ,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Providing and fixing vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with choppe hemp (weste pipe to bemeasured and paid for separately.,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge. Flat back type of size 430mm x 260mm x 350mm.

Providing and fixing C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clanmps etc. (all in C.P. Brass) including cutting holes and makng good the same,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

15mm nominal bore

Providing and fixing Brass stop cocks ,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

15mm dia

Providing and fixing brass full way valve with wheel.,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

15mm nominal bore

20mm nominal bore

Providing and fixing Cast iron cowl .,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

100mm nominal diameter

Providing and fixing P.V.C connection with brass unions :- 300/450mm length.,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

15mm nominal bore

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

white plastic seat and cover

Providing and fixing 600mm x 450 mm bevelled edge miror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers. ,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Constructing manhole with R.C.C top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing:,as per H.P. P W D. specification 1990 volume - I , including carriage of all labour equipments and materials to various location through all modes of transportation in all leads and lifts and carriage of materials and as per entire satisfaction of Engineer- in- charge.

Inside size 800mm x 800mm and 500mm deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm internal dimensions total weight of cover and frame to be not less than 38kg . (weight of cover 23 kg and weight of frane 15 kg.)

With 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand).

vijay singh thakur

ANIL KUMAR

BHARAT BHUSHAN

JAGMOHAN CHAUHAN