Repair and Maintenance works to Kannur office building,Palllikunnu ,Kannur

Amount

Finishing with Epoxy paint (two or more coats) at appropriate locations prepared and applied as per manufacturer's specifications Asian paints/ equivalent make including appropriate priming coat, preparation of surface, all materials labour charges etc. complete as per the direction of Engineer in charge.

Painting on exterior wall surface including surface cleaning, crack filling, 1 coat damp proof ultra, 2 coat Asian Ultima Protek / equivalent White material, labour etc complete

Painting over metal surface including surface cleaning, crack filling, 1 coat high performance yellow metal primer , 2 coat Asian Apcolite premium satin enamel/ equivalent, including all material labour charges etc complete

Painting on exterior exposed stone surface Including surface cleaning, 2 coat Apex tile guard clear / equivalent including all material labour charges etc complete.

Priming coat for walls Including crack filling with silicon, 2 coat Sealoxy Water Proof Primer, 2 coat sealer coat ( damp Proof), labour etc (staircase wall inside and outside)

Façade glass work Window maintenance: includes maintenance of hinges , handles ,beading. Providing silicon in deteriorated portions. Replacement of locks and handles shall be done.Cleaning works shall be done with water and ammonium hydroxide or ammonia solution as per the direction of engineer in charge.

Cleaning works to inside and outside of glass work with water and ammonium hydroxide or ammonia solution including maintenance of beadings and silicon at deteriorated portions

Replacement of existing hinges including labour and material cost

Replacement of existing handles including labour and material cost

Providing parapet projection with precoated galvanised iron trefford sheets (JSW/Bhusan or equivalent make) fixing support post from RCC slab, covering over parapet wall with proper rafters and purlins of GI pipe ,with adequate pvc gutter and clearing water to both ends, providing and applying one coat of primer and synthetic epoxy paint, covering bottom part with GI liner sheet including all materials, labour charges etc complete for third floor as per the direction of Engineer in charge

Steel work in built up 14 gauge G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing 6 inch UPVC gutter with GI clamps at every 1.5 feet intervals with all materials , labour charges etc complete and collecting rain water to the manholes at ground level as directed by engineer in charge.

Liner Sheets for false ceiling- Wooden grain design GI liner sheet of 0.35mm thickness and frame of SHS 40x40x2mm GI tube

Restoration and maintenance of existing RCC parapet wall including plastering if necessary with all materials , labour charges etc complete.

Fortification of existing parapet wall with 4mm thick square net welded over MS angle (50x50x5mm) frame on all sides .MS flat 50x6mm diagonal fixed to support post at RCC slab on all sides .Providing and applying one coat primer and one coat synthetic epoxy paint including all materials , labour charges etc complete for third floor as directed by Engineer in charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing GI 4mm square mesh welded to built up sections including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing all labour and materiral for fixing sunshade with proper rafters and purlins at adequate intervals of GI pipe (Apollo/equivalent) and laying GI Roofing sheet (0.4mm) JSW/Bhusan/equivalent for toilet block (7 floors) and outside wall (3floors)

Steel work for purlin/single section with 14 gauge G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Open terrace roofing with galvanized iron profile sheets with proper rafters and purlins at adequate intervals of GI pipe including all labour charges etc complete for 3rd floor

Steel work in built up 14 gauge G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Providing and fixing recoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing 6 inch UPVC gutter with GI clamps at every 1.5 feet intervals with all materials , labour charges etc complete and collecting rain water to the manholes at ground level as directed by engineer in charge.

Open terrace roofing with galvanized iron profile sheets with proper rafters and purlins at adequate intervals of GI pipe including all labour charges etc complete for 6th floor

Steel work in built up 14 guage G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Providing and fixing recoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing 6 inch UPVC gutter with GI clamps at every 1.5 feet intervals with all materials , labour charges etc complete and collecting rain water to the manholes at ground level as directed by engineer in charge.

Providing roofing sheet over water tank

Steel work in built up 14 guage G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Providing and fixing recoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Maintainence works shall be done for existing fire stair handrail and main staircase handrails after removing deteriorated handrails and clamps including necessary painting with primer coating including cost of materials and labour charges etc complete as directed by engineer in charge.

Broken tiles shall be dismantled and debris shall be removed from the site. New vitrified tiles of 60 cm X 60cm size . Ivory/ approved colour of Johnson, Nitco, Kajaria, Somany / equivalent make shall be laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand).(including all labour , materials ) from ground floor to third floor

Providing all labour and material for laying skirting tiles with 60cmx60cm size laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc.,complete as per the direction of Engineer in charge

Existing broken wall tiles shall be dismantled and new tiles of size 30x30cm in 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc.,complete.shall be laid on walls for toilets in each floor including cost of materials , labour charges etc complete

Providing manhole of size 75 cm x 75 cm x 100 cm on ground for collecting the rain water from roof top with outer frame ISA 75x75x6 and grating flat 70 x8 mm including masonry work as directed by Engineer in charge.

: Supplying and fixing the sanitary fittings (Hindware/ equivalent make) in replacement to the existing damaged items including cost of all materials , labour charges etc complete as directed by the engineer in charge.

Hindware/ equivalent make RWC+Tank

Hindware/ equivalent make wash Basin 20

Hindware/ equivalent make Urinal corto

Hindware/ equivalent make One piece closet

Hindware/ equivalent make Orissa pan

Hindware/ equivalent make piller cock

Hindware/ equivalent make 12 piller cock

Hindware/ equivalent make waist coupling

Hindware/ equivalent make angle cock

Hindware/ equivalent make H/F

SIMI ANZAR

HARIDAS A A