PROVN OF BILING COUNTER AT BLDG NO. T-311 AND SPECIAL REPAIR WORKS TO BLDG NO. T-145, T-130 OF HQ 121(I) INF BDE CAMP AT KARGIL.

Amount

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards / slabs / blankets, any thickness, including cover fillets complete all as specfied and directed.

Dismantling timber scantling in fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section (unframed work) complete all as specfied and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided complete all as specfied and directed.

Demolition of brick or stone/block masonry built in cement mortar including all quions, arches, pillars etc., but excluding ashlar facings, dressed stone works and precast cement articles, complete all as specified and directed by Engr-in-Charge.

Dismantling of structural steel work including doors, gates but excluding framed truss etc complete all as specfied and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 Sqm each complete all as specfied and directed.

Taking up or down steel water tubing 15 mm bore of pipe and connections, including cleaning for reuse if found serviceable or removal to store , complete all as specified and directed by Engr-in-Charge.

Taking up or down steel water tubing 20 mm bore of pipe and connections, including cleaning for reuse if found serviceable or removal to store, complete all as specified and directed by Engr-in-Charge.

Dismantling water tank of capacity exceeding 500 liters and not exceeding 1000 liters and removing to store complete all as specfied and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specfied and directed.

Dismantling of plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed by Engr-in-Charge.

Excavation in trenches, not exceeding 1.5 metres wide and not exceeding1.5 mtrs in depth for foundations etc and getting out in hard / dense soil complete all as specfied and directed.

Returning, filling in soft/loose soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick, complete all as specified and directed by Engineer-in-charge.

Removal surplus soil not exceeding 50mtr and depositing where directed at level not exceeding 1.5mtr above the starting point, complete all as specified and directed by Engineer-in-charge.

M & L for precast cement concrete block masonry with solid blocks, etc. exceeding 10cm in width made out of cement concrete (1:3:6) type C1 using 20mm graded stone aggregate and setting in cement mortar (1:6), complete all as specfied and directed.

M&L for Rendering 15 mm thick in cement mortar 1:4 on fair faces of brick masonry, finished the surface even and smooth without using extra cement, complete all as specified and directed by Engineer-in-charge.

M&L for Plain fillets of second class soft wood (KAIL) sectional area exceeding 13 Sqcm and not exceeding 25 Sqcm, square, rectangular or triangular in section, clean sawn, secured with nails, complete all as specified and directed by Engr-in-Charge.

S&F 9 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails to timber frame work complete, all as specified and directed by Engr-in-Charge

M&L for 18mm thick block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame work complete allas specified and directed.

S&F for 1mm thick designer sunmica on ply board with adhesive complete all as specified and directed by Engr-in-Charge.

S & F in repair 4mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each pane, complete all as specified and directed by Engr-in-Charge.

S & F in repair sheet glass, 5.5mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and directed by Engr-in-Charge.

M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectagular) polished,area of each tiles not exceeding 0.36 sq m , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed by Engr-in-Charge.

M & L for Glazed ceramic coloured tiles of size 300x200x7 mm thick on vertical surface such as in dado/skirting/risers to steps etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles laid over and including 10 mm thick rendering in CM (1:4), complete all as specified and directed by Engr-in-Charge.

M&L for Non-skid coloured ceramic tiles, 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc, set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles laid over including 15 mm thick screed bead in CM 1:4, complete all as specified and directed by Engr-in-Charge.

Material and labour for kota stone flooring 20-25mm thick over cement screed bed laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed by Engr-in-Charge.

M&L for Granite (of any type) 20mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone incl grinding and polishing over and including 15mm thick bedding layer in CM 1:4,complete all as specified and directed by Engr-in-Charge.

M&L for chequered cement concrete tiles 20x20x25mm thick, with grey cement and no pigments, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed in cement mortar in (1:4), complete all as specified and directed by Engr-in-Charge.

M&L mild steel TMT bars 10 mm dia and over cut to length bent to shape required inclduing cranking bending spirally for hooping ends and binding with and incl mild steel wire (annelaed) not less than 0.90 mm dia or securing with clips complete all as specfied and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) for flat rough surfaces of concrete complete all as specfied and directed.

M&L for RCC, 1:2:4, type B-1 (20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs etc, complete all as specified and directed by Engr-in-Charge.

M & L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in sub base, floor, path, pavings etc.

M&L for 75 mm thick PCC 1:3:6 type C-2 using (40mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

M&L for 2nd Class soft wood moulding as in cornicses, picture, rails and the like n.exc.6 sq cm., complete all as specified and directed by Engr-in-Charge

M & L for second class soft wood plain fillets, square , rectangular or triangular in section , clean sawn secured with nails or brads of sectional area exceeding 3 Sqcm and not exceeding 6 Sqcm complete all as specfied and directed.

M&L for second class soft wood plain, solid, straight chowkats and frames, wrought, frame rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specfied and directed.

S&F factory made plain framed 35mm thick panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces (The size of rails and style as per IS 1003 (Part I), kiln seasoned and chemically pressure treated), rail and style made of second class hard wood complete all as specfied and directed.

S&F 30 mm thick 2nd class soft wood skeleton shutters, divided into square with plain chamfered or rounded mitrerd and rebated sash bars for windows any numbers, size of stiles and rail as specified in SSR (2009) Part-I section 8 clause 8.24 (b) complete all as specfied and directed.

S & F MS framed work such as grills, gratings, etc., with end of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specfied and directed.

S&F mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 100mm complete all as specfied and directed.

S & F aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt 200mm complete all as specfied and directed.

S&F 125mm long, mild steel handles cast type, fitted complete all as specified and directed by Engineer-in-Charge.

S & F 150 mm mild steel pressed handles, oval type, stove enamelled black complete all as specfied and directed.

S & F butt hinges, medium weight, cold rolled mild steel and fixed, size of hinges 100mm complete all as specfied and directed.

S & F butt hinges, medium weight, cold rolled mild steel and fixed, size of hinges 75mm complete all as specfied and directed.

S&F mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, length of bolt 300mm complete all as specfied and directed.

S&F 20mm dia aluminium alloy anodised curtain rails with fixing brackets, stops, rollers etc complete all as specfied and directed.

Prepation of new wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel Paint over a coat of pink primer, complete all as specified and directed by Engr-in-Charge.

Preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge.

Preparation of newly plastered surfaces of wall and applying two coats of cement based paint over a coat of white cement primer complete all as specified and directed.

Preparation of old plastered surfaces of walls and applying two coats of oil bound distemper with approved colour and shade, complete all as specified and directed by Engr-in-Charge.

Supply and fixing 15mm dia GI tube medium grade galvanised, with all fitting and fixed to walls and ceilings or laid in floors, complete all as specified and directed by Engr-in-Charge.

Supply and fixing 20mm dia GI tube medium grade galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed by Engr-in-Charge.

S&F grating doom 125mm dia with waste hole of PTMT (Minimum weight 40 gms), complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair Bib taps,15 mm bore,fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for brass ferrule, complete all as specified and directed by Engr-in-Charge.

Supply and fixing 1000 Ltr capacity Rotational moulded HDPE water storage tanks (Cylindrical vertical closed top), double wall construction, hoisted and fixed in position or placed in position inside or outside the building, connecting up pipes and securing access covers, complete all as specified and directed by Engr-in-Charge.

S&F kitchen basket with 100% stainless steel, non magnetic, multilayer chrome plated, argon welded, doubloe sealed ball bearing mechanism kitchen capable of holding plates , cup, saucers bowls and dongas with 600 car case complete all as specified and directed by Engineer-in-Charge.

S&F hook rail pull out 18" long with 100% stainless steel non-magnetic multilayer chrome plated, argon welded completed all as specified and directed by Engineer-in-Charge.

S&F 0.63mm thick, galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc, with grade of zinc coating 275, complete all as specified and directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to walls,fixed with J type hook, complete all as specified and directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to walls,fixed with J type hook, complete all as specified and directed by Engr-in-Charge.

Demolition and breaking up PVC drain pipes, complete all as specified and directed by Engineer-in-charge.

S&F PVC (SWR) 110mm bore pipes single socketed, ISI marked, in any length with rubber ring joints, laid in trenches or in floors.

S&F PVC (SWR) bends any radius of 110mm bore, complete all as specified and directed by Engineer-in-charge.

Taking down carefully copper or aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches ceiling roses, pendants, sockets bulk, head fitting, tube light fitting by unscrewing carefully from boards etc and making good, distrubed surface of walls floors etc. , complete all as specified and directed by Engr-in-Charge.

Point wiring with multistraded copperconductor PVC insulated and unsheathed cable in PVC casing and caping 1.5 Sq mm with all fittings /accessories and including 1.5 Sq mm PVC insulated copper earth wire connected common earth including closed recessed wodden terminal boxes of suitable size made of 2nd class hard wood for mounting of switches,socket setc with 3 mm thick laminated sheet cover for one light point or for one three pin socket outlet 5A or bell/buzzer point independent controlled by one switch , complete all as specified. and directed by Engr-in-Charge

All as per Srl item No 67 here in before but for one 3 pin 5 Amps switch socket on same board.

All as per Srl item No 67 here in before but for one 3 pin socket outlet 5 Amps on independent board.

All as per srl item No 67 here-in-before but using 4 sqmm single core copper conductor cable of multistranded PVC insulated unsheathed 1100 volts grade for industrial plug socket point including running of 2.5 sqmm copper conductor PVC wire as earth continuity conductor alongwith wiring and connecting to the common earth dolly.

S&F Switch piano 5 Amps, single pole one way flush type, complete all as specified and directed by Engr-in-Charge.

S&F Switch socket combination 2 in 1, and 3 and 2 pin, 5 Amps Flush type, complete all as specified and directed by Engr-in-Charge.

S&F Switch socket combination 2 in 1, 5 and 15 Amps, Flush type, complete all as specified and directed by Engr-in-Charge.

S&F Lamp holder, insulated body with back plate suitable for batten fittings, complete all as specified and directed by Engr-in-Charge.

S&F ceiling rose,surface backlite 65mmx 50mm two or three terminals , complete all as specified. and directed by Engr-in-Charge

Sheet metal enclosure for DB's double door, single pole and neutral, 240V, 8 way with 200 Amp rated bus bar including blanking plates where required. complete all as specified and directed by Engr-in-Charge.

S&F Isolator single pole & Nuetral 240 V 63 Amps capacity including suitable size copper Lugs, complete all as specified. and directed by Engr-in-Charge.

S&F Isolator single pole & Nuetral 240 V 40 Amps capacity including suitable size copper Lugs, complete all as specified. and directed by Engr-in-Charge

S&F MCB single pole 240V AC 5 to 32 Amps 10 KA , complete all as specified and directed by Engr-in-Charge.

Sub main wiring with two single core 2x6 sqmm multistranded copper conductor cable, PVC insulated cable 1100 volts grade and 4.0 Sqmm as continous earthing drawing and including PVC condut, complete all as specified. and directed by Engr-in-Charge

Earthing complete with galvanised MS earth plate eletrode 600x600x6mm thick,burried directly in ground (earth pit not less than 2.25mm deep below GL) with top edge of the plate n.less than 1.5mtr below normal.GL surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all round the plate using 4mm dia GI wire as earth wire electrode welded and revetted to earth plate at one end connected to main DBs of Bldg at another end GI earth wire encased in and including 15mm dia GI light grade pipe through upper end of earth plate upto main DB of bldg with 20mm bore GI pipe light grade as water pipe from earth chamber to upper edge of earth plate MS funnel with wire mesh fixed on water pipe and Provn of PCC pit in PCC 1:2:4 type B-1 chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type BI duly reinforeced with MS bars 8mm dia @ 150C/c with both ways complete with lifting handle all as shown in electrical plate no 3 of SSR of part-I (2009) complete all as specified and directed by Engr-in-charge.

Supply and laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts, cross-sectional area 35 Sqmm 2 core laid in trenches/ducts, passing through pipes or along poles, complete all as specified and directed by the Engr-in-Charge.

Supply and Fixing LED 18 Watt tubelight fitting decorateive ultra slim square profile leinear with extruded polycarbonate environoment friendly, Make Havells Cat Part LUMILINEPLUSBS18WLED865SPCSS or equvilanat in Philips/Wipro complete all as specified and directed by Engr-in-Charge.

Supply and Fixing LED building security light 60 watt energy efficient with bracket, suitable dia pipe for fixing the street light in wall as as directed. Make : Havells Cat Part No. ENDURAPEARLNEOSL60WLED757PASYTOPC or equivalent model in Philips/Wipro complete all as specified and directed by Engr-in-Charge..

Note : - Contract sum will be derived after deduction of Rs. 31431.00 as listed in Schedule `A` Part -II (Schedule of credit).

M/S MOHD HUSSAIN

M/S SUN RISE BUILDERS