CWE/FZR- /2022-23 Special repair to bldg. No P-167 Sec Hosp at Dholewal Mil complex under GE Ludhiana

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level) complete all as specified and as directed by Engineer-in-charge.

Demolition of reinforcement cement concrete as in Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and as directed by Engineer-in-charge.

Reinforced Cement Concrete type B1 1:2:4 (nominal mix ) (using 20 mm graded stone aggregate) in beam/slab/Chajjas etc complete all as specified and as directed by Engineer-in-charge.

Use and waste rough finished flat Form work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports etc complete all as specified and as directed by Engineer-in-charge.

Use and waste rough finished Form work to edges of concrete floor and roofs and similar work exceeding 5 Cm but not exceeding 10 Cm wide complete all as specified and as directed by Engineer-in-charge.

Material and labour mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality complete all as specified and as directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing, serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engineer-in-charge.

Material and labour Vitrified ceramic dark shade coloured tiles 8-10mm thick square/rectungular polished area of each tile area exc 0.42 Square meter not exceeding 1.0 Square meter in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15 mm thick screed bed of cm 1:4 complete all as specified and as directed by Engineer-in-charge.

Complete all as specified serial item No 08 here-in-before above but as in skirting over rendering 10mm thick in cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge.

Material and labour non skid cerermic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc. 0.11 sqm but n.exc. 0.18 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement with pigment to match over 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed by Engineer-in-charge.

Complete all as per sierla item No 10 here-in-before above but as in skirting over rendering 10mm thick in cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge.

Material and labour glazed ceramic coloured/ printed tiles 450mm x 300mm x 6 to 7mm thick on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick bedding layer in cement mortar (1:3) including necessary cutting as per site requirement complete all as specified and as directed by Engineer-in-charge.

Material and labour 25mm thick Cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in base flooring rough finished surface complete all as specified and as directed by Engineer-in-charge.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and as directed by Engineer-in-charge.

Material and labour granite slab (of any type) 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in 15mm thick screed bed of cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite complete all as specified and as directed by Engineer-in-charge.

Demolition of brickwork built in cement or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed by Engineer-in-charge.

Material and labour brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in cm 1:6 complete all as specified and as directed by Engineer-in-charge.

Complete all as per serial item No 17 here-in-before above but except bricks complete all as specified and as directed by Engineer-in-charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/ slabs/ blankets any thickness including cover fillets complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing GI frame work 605mmx605mm grid for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screw 450mm centre to centre / intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approxmate 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section ( not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified & as directed by Engineer-in- charge.

Supply & fixing, 4mm thick non asbestos fibre cement building board fixed or laid / inserted to aluminium / GI frame work all as specified & as directed by Engineer-in- charge

Supply and fixing stainless steel steel wire cloth 0.36 mm nominal dia and average width of aperture 1.40 mm and fixed with ss wire staple complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n. exc 0.5 Square meter each panes complete all as specified and as directed by Engineer-in-charge.

Taking down chowkats or frames(without taking off shutters from the frame) area n.exc 1.5 Sqm each complete all as specified and as directed by Engineer-in-charge.

Taking down chowkats or frames exc 1.5 Sqm but n.exc 4.0 Sqm with shutters (without taking off shutters from the frame) complete all as specified and as directed by Engineer-in-charge.

Supply and fixing of aluminium Powder coated of any coluor anodised frame for doors, windows, ventilator, with one or more rebates including joining cleat for fixing etc complete all as specified and as directed by Engineer-in-charge.

Supply and fixing anodiesed Powder coated of any color Aluminium door shutters, aluminium section weighing 0.55 Kg/m incl necessary jointing cleats,glazing clips,ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and as directed by Engineer-in-charge.

Supply and fixing anodiesed Powder coated of any color three track Aluminium sliding windows aluminium section weighing 0.55Kg/m including necessary jointing cleats,glazing clips,ruber neoprene packing, incl 5.5 mm thick tinted/ frosted glass, stainless steel wire cloth of 0.36 mm nomial dia with aparture 1.40 mm ,anodised aluminium fittings such as locking arrangenment and suitable handle complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair 4 Levers Brass Mortice lack, vertical type, of size 100mm complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 5.5mm thick sheet glass ordinary quality & glazing in Aluminium door/ window with neoprine rubber and frosted on one side in squares exc. 0.5 sqm each pane complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 5.5mm thick sheet glass ordinary quality & glazing in Aluminium door/ window with neoprine rubber and frosted on one side in squares n. exc. 0.5 sqm each pane complete all as specified and as directed by Engineer-in-charge.

Supply and fixing PVC wall lining consisting of 5mm thick wood grain printed colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame /Aluminium door at site etc complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in repairs door closer aluminium (extruded section) hydraulically regulated designation No. 03, universal type, suitable for door shutters of 851mm to 1000mm in width and weight between 61kgs to 80 Kgs complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engineer-in-charge.

Supply and fixing aluminium handles anodised cast type 150mm long all as specified & as directed by Engineer-in-charge.

Supply and fixing extruded Aluminium type B-21 butt hinge 100 mm long complete all as specified and as directed by Engineer-in-charge.

Supply and fixing double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed by Engineer-in-charge.

Material and labour soild PVC wall linning vonsisting of 5mm thick single side prelam colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawings complete all as specified and as directed by Engineer-in-charge.

Material and labour 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawings complete all as specified and as directed by Engineer-in-charge.

Supply and fixing solid PVC door frame of size 50mmx47mm made out of 5mm plain glover PVC sheet reinforced with MS square tube in opening as per specification and drawing complete all as specified and as directed by Engineer-in-charge.

Supply and fixing factory made soilid panel PVC Door shutter 30mm thick (Stype) consisting of frame made out MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having PVC sheet stripof 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail, & bottom rail; Panneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing complete all as specified and as directed by Engineer-in-charge.

Taking up or down steel tubing 15mm bore and connections, including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-charge.

Complete all as pe serial item No. 42 here-in-beforer above above but 20mm bore.

Supply and fixing 15mm GI tubes, medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer-in-charge.

Complete all as per serial item No 42 here-in-before above but 20mm bore.

Refixing old steel tubing and connections in new or old postion (wall, ceiling , floors ,etc) 15mm bore complete all as specified and as directed by Engineer-in-charge.

Complete all as per serial item No 46 here-in-before above but all as per above item but 20mm bore.

Supply and fixing in repairs ball brass valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore pipe complete all as specified and as directed by Engineer-in-charge.

Supply and fixing stop valves 20mm, cast copper alloy, screwed down, high pressure with crutch or butterfly handle etc complete fixed in repairs complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repairs Rotational moulded polythylene water strarge tanks 500 ltr (Cylinderical vertical with closed top ) hoisted and fiexed in position all as per specified in SSR Pt-1 complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repairs Rotational moulded polythylene water strarge tanks 1000 ltr (Cylinderical vertical with closed top ) hoisted and fiexed in position all as per specified in SSR Pt-1 complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repairs vitreous china wash down water closet pedestal pattern pan white with trap including connection to existing out joint pipe, flushing pipe or Cistern, antisyphonage pipe, including making, etc complete including making goood to floor etc complete all as specified and as directed complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair plastic water closet seat cover of White colour closed pattern with flat bottom and cover with mild steel chromium plated hinging device etc complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair vitreous china washbasin, white, flat back, size 550mm x 400mm, including brackets & incl 32mm bore waste fitting brass, CP for glazed ware basinetc with long screwed shanks and fly-nuts flange end bedded in red lead cement and other end complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair vitreous china washbasin, white, flat back, size 550mm x 400mm, including brackets & incl 32mm bore waste fitting brass, CP for glazed ware basinetc with long screwed shanks and fly-nuts flange end bedded in red lead cement and other end fixed including pedastal for washbasin complete all as specified and as directed by Engineer-in-charge.

Material and labour 75mm dia cast iron floor trap with grating incl jointing to waste pipe with run lead joint and embedde in cement concrete (1:2:4) type B0-1 using graded stoe agg complete all as specified and as directed by Engineer-in-Charge

Supply and fixing cast copper alloy chromium plated fancy type single lever basin mixer complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing bib taps chromium plated fancy type, cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repair 15mm bore complete all as specified and directed by Engineer-in-Charge.

Supply and fixing C P health faucet suitable for Europian western commode (EWC) including PVC connection 15mm size with PTMT nuts and washer, of length 900mm complete all as specified and as directed by Engineer-in-charge.

Supply and fixing soap dish fixed to walls with chromium plated brass screws complete all as specified and as directed by Engineer-in-charge.

Supply and fixing stop valves/angle valve 15mm, chromium plated,fancy type, complete fixed in repairs complete all as specified and as directed by Engineer-in-charge.

Supply and fixing PVC connections 15mm size with PTMT nuts of legth 600mm complete all as specified and as directed by Engineer-in-charge.

Supply and fixing toilet paper holder of CP fixed to walls with chromium plated brass screws complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repairs brass chromium plated tubular towel rail, 20mm dia D-type, 60cm long between flange complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 10 ltr capacity PVC valveless, syphonic action type flushing cistern,low level, white, with inlet, ball valve, float and handle incl brackets fixed inrepairs complete all as specified and as directed by Engineer-in-charge.

Material and labour two coat of white wash to old surfaces of walls after preparation old surface complete all as specified and as directed by Engineer-in-charge.

Complete all as per serial item no 68 here-in-before above but on ceiling surfaces.

Supply and fixing in repairs pre-laminated (both sides) particle board 18/19mm thick with decorative choice laminations, interior grade, fixed with screws to timber frame work complete all as specified and as directed by Engineer-in-charge.

Supply and fixing aluminium handle cast type anodised of size 75mm complete all as specified and as directed by Engineer-in-charge.

Taking down curtain rod along with wooden pallmate laid on wall complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair curtain rod made out of 25mm dia(outer dia )pipe having thickness 0.63mm , PVC coated and colour/pattern, over all dia 28 to 29 mm complete all as specified and as directed by Engineer-in-charge.

Supply and fixing plastic finial of 28 to 29mm bore, decorated type, of any colour/pattern, best quality to suit the curtain rod and fixed at the end of curtain rod with suitable adhesive complete all as specified and as directed by Engineer-in-charge.

Supply and fixing mild steel prepainted bracket to hold the curtain rod and fixed to wall(Concrete/brick masonry) with the help of 2 Nos 50mm long steel screws and rawl plug included drilling with electric drill and making good the disturbed surfaces complete all as specified and as directed by Engineer-in-charge.

Demolition and breaking up drain pipes/pipe fixed to wall (PVC, Salt glazed ware, AC or re-inforced concrete) set in cement mortar bore of pipe 100mm all as directed by Engineer-in-charge.

Supply and fixing 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 75mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified and as directed by Engineer-in-charge.

Supply and fixing PVC (SWR) bend any radius 110mm bore complete all as specified and as directed by Engineer-in-charge.

Supply and fixing PVC (SWR) 'P' trap radius 110/110mm bore complete all as specified and as directed by Engineer-in-charge.

Material and labour endura ceramic tiles (Ist quailty) of size 300mmx300mmx10mm thick laid in floors etc., set and jointed in neat cement slurry and pointed in grey or coloured cement and pigment to match the shade of tile laid over and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing floor doors stoppers of aluminium alloy body and tenque anodisede with hard drawn steel spring fixed in floor 150mm long complete all as specified and as directed by Engineer-in-charge.

Dismantling brick tiles or terracing tiles sinlge layer on roofs complete all as specified and as directed by Engineer-in-charge.

Demolition of mud in roofs any thickness including plastering and leeping (whether full thickness removed or only a part there of) complete all as specified and as directed by Engineer-in-charge.

Material and labour for wire brushing neat cement slurry with 3kg of cement per sq m at top and bottom of base coat and cleaning top surface complete all as specified and as directed by Engineer-in-charge.

Material and labour for PCC 1:2:4 type B-0 (12.5mm graded agg) as roof padding/ roof kerb concrete complete all as specified and as directed by Engineer-in-charge.

Material and labour priming surfaces and applying normal treatment (for moderate conditions) using bitumen primer @ .30 Kg/Sqm applied hot complete all as specified and as directed by Engineer-in-charge.

Material and labour for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2kg per sq.m incl cleaning surfaces complete all as specified and as directed by Engineer-in-charge.

Material and labour for fixing APP based polymeric membrane minimum weighing 3kg/sqm and min 3mm thick reinforced with polyster non woven fabric (wt not less than 150gms/sqm) land on primered surface by torced application complete all as specified and as directed by Engineer-in-charge.

Material and labour 40mm thick brick tiles laid on 15mm thick cement mortar 1:6 and joints grouted flush in cement mortar 1:3 mixed with 5% 0f crude oil by weight of cement complete all as specified and as directed by Engineer-in-charge.

Complete all as per serial item No 90 here-in-before above but except tiles after clening and removing old mortar from bricks complete all as specified and as directed by Engineer-in-charge.

Material and labour flush pointing to brick laid flat or brick tiles in paving cement mortar in 1:3 complete all as specified and as directed by Engineer-in-charge.

Material and labour PCC 1:2:4 type B1 (using 20mm graded stone aggregate) in roof kerbs or mud stops, benching rounded or chamfered on edges complete all as specified and as directed by Engineer-in-charge.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc complete all as specified and as directed by Engineer-in-charge.

Material & Labour 12mm thick plastering on fair faces of bricks or cone surfaces finished even and smooth w/o using extra cement in cm1:6 complete all as specified and as directed by Engineer-in-charge.

Material and labour 5mm thick plastering on fair faces ofr cone surfaces finished even and smooth w/o using extra cement in cm 1:3 on ceiling complete all as specified and as directed by Engineer-in-charge.

Material and labour 15mm thick plastering on fair faces of bricks or concrete surfaces finished even and smooth w/o using extra cement in cm1:4 complete all as specified and as directed by Engineer-in-charge.

Material and labour Preparing of new surface of plaster and applying three coats of white wash on ceiling complete all as specified and as directed by Engineer-in-charge.

Material and labour for Preparing of new plastered surface and applying two coats cement base paints on wallscomplete all as specified and as directed by Engineer-in-charge.

Material and labour for Preparation of new surface of wall and applying two coat of oil emulsion white or printed on walls over 3mm thick Birla wall care putty filling on plastering surface complete all as specified and as directed by Engineer-in-charge.

Material and labour Preparation of old surfaces of wallsand applying one coat of cement base paint complete all as specified and as directed by Engineer-in-charge.

Material and labour for complete removal of existing treatment and applying two coats of oil bound emulsion white or printed on walls. over 3mm thick Birla wall care putty including preparation of surfaces of wall complete all as specified and as directed by Engineer-in-charge.

Material and labour for preparation of old painted Steel surfaces of any description not other wise described over 10cm width or girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge

Material and labour for repairing RCC projection chajjas, roof, facia etc. by necessary preparation, scraping, cutting, chiseling derusting and cleaning exposed reinforcement surfaces of damaged, loose RCC surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregates and reinforcement with welded mesh of weight exc 2Kg per Sqm but n.exc 3Kg/Sqm (if required) with or without facia and finished with cement morte 1:3 using coarse sand and work in patches area n.exc 5 Sqm and thickness RCC member n.exc 70mm incl necessary formwork and applying two coats of finishes to match with the existing surfaces at any height complete. (note: wlded mesh to be paid separately) complete all as specified and as directed by Engineer-in-charge.

Supply and fixing framed work as in doors or gate,coolers stand of angle or others section etc confirming to Fe 410-s complete all as specified and as directed by Engineer-in-charge.

Material and labour for 75 mm th cement concrete type C-2,1:3:6 40 mm graded aggregate for plinth protection complete all as specified and as directed by Engineer-in-charge.

Hacking out old broken glass (any thickness) , size, quality or description ) from metal frame area n.exc 0.5 Sqm in each pane including punching or drilling out old glazing pins and providing and fixing new ones.(ref item no 23) complete all as specified and as directed by Engineer-in-charge.

Supply and fixing weldind for Expanded metal,not exc 4 kg cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members (ref item no 104) complete all as specified and as directed by Engineer-in-charge.

Taking down old burnt copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc using putty and distemper complete all as specified and as directed by Engineer-in-charge.

Material and labour point wiring complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through and including 20mm dia PVC rigid non metallic conduit with all accessories such as internal bend end caps and module boxes flush type for housing of module boxes flush type for housing of module boxs concealed in wall with screws & washers complete concealed in walls (surface on beam/ceiling/roof etc) including proivision of 1.5 sqmm copper conductor cable as earth continuity conductor One light/fan point controlled by one, one way switch., complete all as specified and as directed by Engineer-in-charge.

Complete all as specified serial item No 110 here-in-before above but one swich socket outlet point 5 Amps on independent board. and regulator complete all as specified and as directed by Engineer-in-charge.

Complete all as specified serial item No 110 here-in-before above but One 3 pin socket outlet, 5 Amps on the same board with other switch complete all as specified and as directed by Engineer-in-charge.

All as per item No 110 described here-in-before but with copper conductor cable FR LS 4.0 Sqmm for one 3 pin socket outlet, 15 Amps and including provision of 4.0 Sqmm PVC insulated copper conductor cable as earth continuity conductor on independent board complete all as specified and as directed by Engineer-in-charge.

Supply and fixing LED tube light fittings 1200 mm, 20 W, 240V, 50Hz rated input watt 20, operating voltage range 140-270, P.F- not less then 0.95, higher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate environmental friendly, energy efficient complete all as specified and as directed by Engineer-in-charge.

Supply and fixing LED tube light fittings 600 mm, 10W, 240V, 50Hz,, rated input watt 10, oprating voltage range- 140-270, P.F- not less then 0.95, higher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate enviromental friendly, energy efficient complete all as specified and as directed by Engineer-in-charge.

Suppy and fixing energy saving recess mounting deep drawn LED luminaire, 34/36 watt, 6000K suitable for false ceiing of size 60cm x 60cm, having power factor more than 0.90 IP-20 class-I protection with efficiency LED electronic driver BIS approved surge protection 2 KV (minimum), operative on 140 volts 270 volts AC supply, complete prewired, connecting and testing complete all as specified and as directed by Engineer-in-charge.

Supply and fixing ceiling fans complete with all accesseries 230 Volt , single phase, 1200 mm sweep in energy saving BEE 5 star rated complete all as specified and complete all as specified and as directed by Engineer-in-charge.

Supply and fixing exhaust fan 300mm sweep , 230volt, single phase, steel body heavy duty star rated , single phase incl lovers complete with all accesseries in energy saving star rated complete all as specified and as directed by Engineer-in-charge.

Material and labour sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories concealed in wall/Ceiling etc complete all as specified and as directed by Engineer-in-charge.

Material and labour sub main wiring complete with 2 runs of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories concealed in wall/Ceiling etc complete all as specified and as directed by Engineer-in-charge.

Material and labour in factory made powder coated distribution board VTPN 12 way fabricated of CRCA sheet with metal door (IP-43 protection) bar, Neutral bar, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one MCCB 100 Amp , 4 pole as a incomer and 12 SPN MCBs as outgoing complete all as specified and as directed by Engineer-in-charge.

Supply and fixing MCCB TPN 100 amp, 4 pole with bracking capacity 16 kA , 415 volts AC supply ISI marked complete all as specified and as directed by Engineer-in-charge.

Material and labour in factory made powder coated distribution board SP & N 12 way fabricated of CRCA sheet with metal double door type (IP-43 protection) bar, Neutral bar, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as a incomer and 10 SP MCBs as outgoing complete all as specified and as directed by Engineer-in-charge.

Material and labour in factory made powder coated distribution board SP & N 8 way fabricated of CRCA sheet with metal double door type (IP-43 protection) bar, Neutral bar, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as a incomer and 6 SP MCBs as outgoing complete all as specified and as directed by Engineer-in-charge.

Supply and fixing sheet metal enclosure with socket plug top and MCB SPN 20 Amp with enclosure with a two pin and earth plug and socket complete all as specified and as directed by Engineer-in-charge.

Supply and fixing MCB SPN 32 Amps 240 V, C- curve, 50 Hz, breking capacity-10 kA. complete all as specified and as directed by Engineer-in-charge.

Supply and fixing isolator 63 Amps, 415V,3 phase, C- curve, 50 Hz, breking capacity-10 kA complete all as specified and as directed by Engineer-in-charge.

Supply and fixing MCB SP 6-32 Amps240 V, C- curve, 50 Hz, breking capacity-10 kA complete all as specified and as directed by Engineer-in-charge.

Supply and fix ceiling rose surface type bakelite 65 x 50mm with three terminals complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Switch Modular 6A single pole, one way, 1 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Switch Modular 16A single pole, one way, 1 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Socket, 6A - 2/3 pin combined 2 modulecomplete all as specified and as directed by Engineer-in-charge.

Supply and fixing Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Modular White cover plate with frame,12 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Modular White cover plate with frame,8 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Modular White cover plate with frame,4 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Modular White cover plate with frame,3 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Modular White cover plate with frame,2 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Modular Metal flush box 12 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Modular Metal flush box 8 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Modular Metal flush box 4 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Modular Metal flush box 3 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Modular Metal flush box 2 module complete all as specified and as directed by Engineer-in-charge.

Supply and fixing fan step regulator, 120W 2 module complete all as specified and as directed by Engineer-in-charge.

Taking down of any size of building security light fittings complete all as specified and as directed by Engineer-in-charge.

Supply and fixing bldg security light fitting LED 35 W LED made up of pressure die cast aluminium housing with potted isolated driver and high power LED and indl lenses, oprating range- 90V to 340V AC. IP66 with high power LED lamp including with suitable size of bracket complete all as specified and as directed by Engineer-in-charge.

Supply and fixing water heater storage verticle type Geyser of capacity 25 Ltrs BEE 5 star rated complete with all accesseries such as NRV, safty valve, steel connection pipe with all fixing arrangement and groughting suitable size of nuts and bolts and making good to disturbed surface complete all as specified and as directed by Engineer-in-charge.

Supply and fixing of water tube medium grade 15 mm bore in wall floor on/ ground complete all as specified and as directed by Engineer-in-charge.

Supply and fixing wall mounted fan 450 mm size, 230 volt, single phase, plastic body ,light gray colour complete all as specified and as directed by Engineer-in-charge.

Material and labour earthing complete incl neccessary earth work with galvanised steel earth plate electrode 60cm X 60 cm X 6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level with the top edge of electrode not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4mm dia means of bolts, nuts,check nuts and washers of galvanised iron and GI lead protected with protection pipe of GI light grade 15mm dia upto 3mtr above ground level along poles fixed with two clamps of 25mm 3mm flat iron and connected to running earth wire at top of poles and watering pipe 20mm bore of GI medium grade all as shown in electrical plate No 3 of SSR Part-I 2009 connected to earthing test point all as specified and direct and testing on completion including PCC 1:3:6 ) C-I cover and frame excavation and earth work etc complete all as specified in elect plate No 3 of SSR Part -I 2009 Note :- PCC Chamber shall be constructed at least 1.50 mtr away from on the earth pit electrode and pipe for watering shall be provided in slanting manner complete all as specified and as directed by Engineer-in-charge.

Taking down of XLPE cable any size complete all as specified and as directed by Engineer-in-charge.

Supply, laying and testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core complete all as specified and as directed by Engineer-in-charge.

Supply, laying and testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 sqmm 3.5 core complete all as specified and as directed by Engineer-in-charge.

Excavation in trenches soft/loose soil not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of pipes/cables etc getting out and bottom surface to required gradient complete all as specified and as directed by Engineer-in-charge.

Material and labour Returning filling in including spreading leveling watering and well ramming in layers each not exceeding 25 cm thickness complete all as specified and as directed by Engineer-in-charge.

Material and labour Removal of surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed by Engineer-in-charge.

Supplying, filling in trenches, spreading, leveling sand cushioning 8 cm below cable and 15 cm above the cable for under ground cable (18 cm punned down thick shall be considerd for mesurement) complete all as specified and as directed by Engineer-in-charge.

Material and labour Old size sub class 'B' bricks,laid flat in trenches over the cable with length of brick perpendicular to the direction of the cable , adjacent/abutting each other complete all as specified and as directed by Engineer-in-charge.

Supply and fixing of GI tubing galvanised light grade of size 50 mm bore with all fittings and fixed complete to wall , floor and ceilings or laid in tracches ( for protection UG cables) complete all as specified and as directed by Engineer-in-charge.

ANUJ ABROL CONTRACTOR

PK ENTERPRISES

JAY ANN CONSTRUCTION COMPANY

M/s G N Const. Co.

GURPARTAP SINGH GULATI

SHRI GANESH CONSTRUCTION CO.