Renovation of Security Area,AMD, Hyderabad

Amount

Demolition of the brick masonry walls constructed in cement mortar manually with chisels at all floors / locations (upto a height of 25m ) including giving necessary temporary supports and disposing off the debris within a lead of 150m, complete with cost of materials, labour, tools & plants all as per specifications and directions of Engineer-in-charge

Demolishing stone rubble masonry in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 150 metres lead as per direction of Engineer-in-charge

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 150 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 150 metres lead.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 150 metres lead

Of area 3 sq. metres and below

Demolishing cement concrete manually/ by mechanical means including disposal of material within 150 metres lead as per direction of Engineer - in - charge

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Dismantling stainless steel work in built up sections in Pipes,angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. without dismembering and stacking within 50 metres lead.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within1 50 metres lead of:

G.S. Sheet/aluminium sheet

Earth work excavation in trenches or drains, foundation in all kinds of soils, other than hard and soft rock not exceeding 1.5m in depth including consolidating the foundation bed, dewatering, shoring etc., and disposing off the surplus earth within a lead of 150m complete with cost of labour, tools & plants all as per specifications and directions of Engineer-in-Charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to1 50 m and lift upto 1.5 m.

Disposing off surplus earth / Incinerator waste / buildings debris/ concrete or stone debris in contractor’s own lorries at MCH approved dumping yard at contractor’s risk and cost including transportation loading and unloading, tools & plants etc., beyond 150 m initial lead, for all leads including all lifts involved, all as per specifications and directions of Engineer-in-Charge. Note : The quantity loaded in the truck shall be reduced by 30% for debris, 20% for earth & Incinerator waste and 50% in case of stones / rubbles towards voids for payment purpose.

Brick work in cement mortar 1:4 (1 cement :4 sand ) in super structure for walls in C.M 1:4 at all levels, floors and locations (upto a height of 25m ) using best quality conventional kiln burnt light weight bricks of class designation 3.5 N/mm 2 including raking out joints, scaffolding, curing etc., complete with cost of materials, labour, tools & plants all as per specifications and directions of Engineer-in-Charge..

Plain cement concrete of grade 1:2:4 (1cement: 2 sand: 4 aggregate) using 20mm size stone aggregate at all floors and locations (upto a height of 25m ) including cost of mixing, consolidating, curing and finishing the top surface etc., complete with cost of materials, labour, tools & plants all as per specifications and directions of Engineer-in-Charge

Reinforced Cement Concrete 1:1.5:3/M20 (1cement: 1.5 sand: 3 aggregate 20mm size) for lintels, beams, shelves, slabs, columns, footings, sun shades etc. at all locations including cost of mixing, consolidating, curing and finishing the top surface etc.( but excluding the cost of centering & shuttering ) complete with cost of materials,labour, tools & plants all as per specifications and directions of Engineer-in-Charge at all levels

Providing form work, Centering and shuttering for foundations, footings, bases for columns, pedastals, beams, lintels, stair case etc. using steel plates, planks including strutting and propping etc. at all floors and removal of the same for in situ reinforced concrete and plain concrete work including close haking of exposed concrete surfaces etc. complete with cost of materials, labour, tools & plants all as per specifications and directions of Engineer-in-Charge

20mm thick cement plastering in two coats CM 1:3 finished with a floating coat of neat cement over the brick/concrete wall surfaces in superstructure upto a height of 25m including raking out joints, scaffolding, curing, etc., complete with cost of materials, labour, tools & plants all as per specifications and directions of Engineer-in-charge.

Providing and fixing Aerocaon 75mmm thick panels including insatllation, GI channels, necessary hardward, groove filling with putty, mesh tape etc. complete as per speicifications fna directions of Engineer In incharge.

Providing and fixing Aerocaon 50mmm thick panels including insatllation, GI channels, necessary hardward, groove filling with putty, mesh tape, inclduing made provision in the slab for tree as per the site and filling the gap around the tree in the slab portion with flexible/ expandable rubber material , etc. complete as per speicifications and directions of Engineer In incharge.

Providing, fabricating and fixing reinforcement with high yield strength deformed bars or TMT bars of all dia., grade Fe-500D conforming to I.S. 1786 for reinforced concrete works at all levels, floors and heights including supplying, cutting, bending, fixing, and tying in position with 18 gauge soft drawn annealed binding wire etc, all complete with cost of materials, labour, tools & plants, scaffolding all as per specifications and directions of Engineer-in-charge. (Binding wire shall not be measured for payment.)

Supply, fabrication, erection and fixing in position M.S. structural steel work made of MS angles, flats, sheets, tees, channels, pipes, Plates, etc., at all floors and heights including one coat of primer , cost of labour, scaffolding, tools & plants etc., all complete as per specifications and directions of Engineer-in-Charge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket, lock cum handle etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion:-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately)

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.

Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

Providing and laying Vitrified tiles o fthickness 9/10 mm in floor in different sizes with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Double charge vitrified tile polished finish of size 600 x 600 mm

Providing and laying Vitrified tiles of thickness 9/10 mm in different sizes, with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

Applying wall care putty manufactured by M/s Birla or M/s J K cements in two or more coats for areas more than 0.1m2 over a coat of cement primer manufactured by M/s Asian Paints, M/s Berger Paints or equivalent and finishing the surface smooth in level , scraping, filling cracks, and crevices upto 1 mm width with approved crack filling compound, cost of all the materials, tools and plants, labour, scaffolding, cleaning, floors, removing office furniture / Lab equipment and rearranging back the same etc all complete as per specifications and directions of Engineer-in-charge.

Painting on internal surface of ceilings and walls at all floors, heights and locations (upto maximum height of 25 m) using 1st quality Apcolite Premium Interior Emulsion paint of M/s Asian Paints, or Rangoli Super Acrilic Emulsion of M/s Berger Paints or equivalent approved make in two or more coats over the existing painted surface or primer coated surface including preparing the surface by sand papering cleaning and removing the dust, dirt, loose painting, grease, oil stains, cobweb, fungus etc., and filling up small cracks upto 1mm width using approved crack filling compound and applying wall care putty manufactured by M/s Birla or M/s JK Cements wherever necessary for areas upto a 0.1 m2 (beyond this it shall be measured separately in the respective item) complete with cleaning floors, removing office furniture / Lab equipment before painting and rearranging back the same etc., all complete with cost of materials, labour scaffolding, tools & plants all as per specifications and directions of Engineer-in-Charge.

Painting on internal surface of ceilings and walls at all floors heights and locations (upto maximum height of 25 m) using 1st quality Tractor Acrylic Distemper of M/s Asian Paints, or Bison Acrylic Distemper of M/s Berger Paints or equivalent approved make in two or more coats over the existing painted surface or primer coated surface including preparing the surface by sand papering cleaning and removing the dust, dirt, loose painting, grease, oil stains, cobweb, fungus etc., and filling up small cracks upto 1mm width using approved crack filling compound and applying wall care putty manufactured by M/s Birla or M/s JK Cements wherever necessary for areas upto a 0.1 m2 (beyond this it shall be measured separately in the respective item) complete with cleaning floors, removing office furniture / Lab equipment before painting and rearranging back the same etc., all complete with cost of materials, labour, scaffolding, tools & plants all as per specifications and directions of Engineer-in-Charge.

Painting one coat of Cement primer manufactured by M/s. Asian Paint or M/s Berger Paints or equivalent make on the new/ existing oil bound / acrylic washable distemper or lappam painted surface of external/internal walls & ceilings and finishing the surface at all levels, floors and locations (upto maximum height of 25 m) including preparing the surface by sand papering, cleaning and removing the dust, dirt, oil marks, cobwebs etc., filling the cracks and crieves upto 1mm width with approved crack filling compound, and applying wall care putty manufactured by M/s Birla or M/s JK Cements wherever necessary for areas upto a 0.10 m2 (beyond this it shall be measured separately in the respective item) complete with cost of all materials, tools and plants, labour, scaffolding, cleaning floors, removing the office furniture / Lab equipment and rearranging back the same etc all complete as per specifications and directions of Engineer-in-charge.

Painting with first quality exterior emulsion paint of 100% Acrylic based including one coat of exterior primer of APEX of M/s Asian Paints or Weather Coat Smooth of M/s Berger Paints or approved equivalent make and shade with / without a coat of corresponding Exterior emulsion primer of approved shade on the sand face plaster surfaces (new or painted) at all floors heights and locations (upto a maximum height of 30 m) including filling up the small cracks and crevices, with approved filling compound, cleaning ,washing, removing the dust, dirt, scales, grease, oil marks, loose painting thoroughly sand papering, wire brushing if necessary, complete with cost of material, labour, scaffolding, tools & plants etc., all as per specifications and directions of Engineer-in-Incharge.

Synthetic Enamel painting in two or more coats on new work using 1st quality SE paint- Apcolite Synthetic Enamel of M/s Asian paints, or Luxol Hi -Gloss Synthetic Enamel of M/s Berger Paints or approved equivalent make and shade over wood/steel /concrete/road kerb stones surfaces of internal areas at all floors heights and locations (upto a max height of 25 m) including filling up small cracks and crevices with approved filling compound, cleaning, washing, removing the dust, dirt, scales, grease, oil marks, loose painting thoroughly, sand papering wire brushing if necessary, complete with cost of materials, labour, scaffolding, tools and plants all as per specifications and directions of Engineer-in-charge.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing APP (Atactic Polypropylene polymer) modified pre fabricated five layer, 3mm thick water proofing membrane, black finished reinforced with non woven polyster matt, finished on thermo fusible film on the underside manufactured by TEXSA or Roof seal or approved make consisting of coat of bitumen primer for bitumen membrane @0.40litrs per sqm by the same membrane manufacturer of density at 25 deg.C, 0.87 - 0.89kg/ltr and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane torch and sealing all joints an overlap of 100 and 75mm on the longitudinal and transverse directions including continue the treatment on vertical face of tree with minimim height of 300 mm with minimum 300 mm over lap with horizontal treatment and overlaps should be thermo fused to make the surfaces monolithic and preparing the surface and applying 2 coats of reflective aluminum painting on top of the finished surface complete cost of materials, labour, scaffolding tools & plants all as per specifications and directions of Engineer-in-charge. Note: Payment will be made only for flat areas only. No extra payment will be made for overlaps/joints/tucking inside groove etc..

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete

Providing, laying and jointing glazed stoneware pipes class SP-1with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete

100 mm diameter

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), external polastering 20 mm thick in cement mortar 1:3, inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) -With common burnt clay F.P.S. (non modular) bricks of class designation 7.5, etc. complete.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes : Size 120x90 cm-With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm diameter

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 150 metre lead as per direction of Engineer-in-Charge

Laying at or near ground level old kerb stones of all types in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints, except at sharp curve, shall not be more than 5 mm), including making drainage opening wherever required etc. complete as per direction of Engineer-in-charge. (Length of finished kerb edging shall be measured for payment). (Old kerb stones shall be supplied by the department free of cost)

Providing wood work in frames of doors, windows, clear story openings and other frames, wrought framed and fixed in position of required size and shape including one coat of wood primer, sawing, jointing,making rebates for shutters, making grooves as shown in the drawings, finishing the surfaces to the required finish all as per specifications and drawings including necessary MS hold fasts 40 mm X 3 mm thick, 200 mm long / with coach screws including protective painting to the suface that will come in contact with walls, joining materials, labour etc. complete all as per specifications and as directed by the Engineer-in-charge.

Supplying & fixing in position the following type solid core block board flush door shutters 35mm thick single leaf shutter with water proof ply specified below conforming to IS 2202-latest, with external type 20 mm thick teak wood lipping alround, fixing shutters in position to existing teak wooden frames at all floors by cutting/ planning if necessary including the cost of labour for fixing the fittings & fixtures as per requirement with wooden packing pieces if necessary (but excluding the cost of fittings and fixtures with screws which will be paid under relevant item ) complete with cost of materials, labour, tools & plants, scaffolding etc., all as per specification, drawing & as directed by EIC.

35mm thick, 1000/750mm x 2150mm (approx. Size) Masonite moulded decorative door shutters including all accessories & fittings like 3 nos. 100mm SS hinges, one coat of wood primer etc complete.

Providing sun control film to the window glass panes of best quality approved make and colour including cutting into sizes fixing in position complete complete with cost of materials, labour, scaffolding, tools and plants all as per specifications and directions of Engineer-in-charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm dia meter

110 mm dia metre

General Notes: 1. Contractor shall inspect the site to acquaint with the site conditions as well as security conditions 2. All the dismantled/ demolished materials shall be dumped at one place as decided by the department within the lead of 150.0mtr. 3. All the samples of materials which are to be incorporated in the work shall be got approved by the Engineer -In- charge well in advance. 4. It is the responsibility of the contractor to handover the dismantled items to Dept. At site, Contractor shall be held responsible for any shortage/ missing of dismantled items until handing over the same to department stores. 5. The contractor is required to pay his employees / labour as per the prevailing minimum wages approved by State/ Central Govt. The Officer In –Charge or his representative will witness the payment of contractor’s labour and is required to certify that the contractor does not pay less than the minimum wages approved. Payment to the contractor will be released only on such certification from Officer In –Charge. The contractor shall maintain 1. Register of Workmen employed 2. Muster roll 3. Register of wages etc. 6. Contractor shall quote rates for all items after considering cost of materials and labour components and all such conditions leads, lifts, safety precautions, security restrictions that are necessary for satisfactory completion of work as per instructions and site conditions. Security regulations shall be followed. 7. The rates quoted shall include cost of all tools and tackles, manpower including wages, liveries, all wastages and GST, water charges, Labour cess seignorage charges etc. as applicable but exclusive of EPF and ESI. EPF and ESI are reimbursable as per relevant clause on production of proof of payment as per CPWD norms. 8. The contractor has to follow all safety rules of the department and all safety equipments, PPE shall be provided to all workers engaged by him. 9. The contractor shall use only river sand confirming to IS 383 for all cement works involved in the scope of work. 10.) The site shall be cleaned and handed over to Dept. after completing the all works as specified in the tenderom all repsects. No extra payment will be made for cleaning.

KVR INFRA & PROJECTS