Renovation Extension of Inspection hut under JSV Division Nagrota Bagwan

Amount

Excavation in foundation trenches etc. in earth work in all kind of soil lift upto 1.50 meters stacking the excavated soil not more than 3 meters. clear from the edge of the excavation and then soil such as pick Work, jumper work, blasting hard or softs rock by chiselling where the blasting work is prohibited slushy daldal and saturated soil including within all heights, stacking the excavated soil within all leads clear from the edge of excavation and then returning the stacked soil in 15Cm (fifteen Centimetres) layer when required into plinths, sides of foundation consolidating each depossited layer by ramming and watering and then disposing of all surplus excavated earth complete in all respect including all leads and Lifts as per the direction and satisfection of Engineer-In-Charge.

Providing and laying cement concrete 1:5:10 (1cement :5sand :10 graded stone aggregate 40mm nominal size) with 15 % plum and curing complete excluding cost of form work in retaining walls/Breast walls, the size of plums shall usually be 150mm. to 300mm as per H.P.P.W.D specification complete in all respect as per direction and to the entire satisfation of Engineer- in- charge up to leads and lifts.

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in Foundation and plinth complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Providing and laying cement concrete work 1:2:4 (1cement:2sand:4graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in suspended floor roofs,landings, shelves and their supports balconies, beams girders bressumers and centilevers upto floor two level i/c carriage of material within all leads and lifts.

Providing and laying cement concrete 1:1½:3 (1cement:1½ sand :3graded stone aggrigate 20 mm nominal size and curing complete excluding cost of form work in:-

Foundation,footing.bases of columns & the like & the mass concrete complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Column,pillars,posts & struts upto floor two level complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

upto floor two level to floor three level complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Lintels,beams girders bressumers & cantilevers upto floor two level complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

upto floor two level to floor three level complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Suspended floors,roofs,landings.etc. upto floor two level complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

upto floor two level to floor three level complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Stair cases with sloping or stepped soffits complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Boulder filling dry hand packed tightly under floor and retaining wall complete in all respect within all leads & lifts as per entire satisfaction of Engineer in charge.

Providing and laying cement concrete 1:3:6 ( 1 cement: 3 sand: 6 graded stone aggregate 40mm nominal size) with curing complete excluding cost of from work in Foundation, Plinth complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Composit Ashler stone masonary using in super structure above plinth level with cement mortar 1:6 (1 cement :6 sand) complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Brick work using common burnt clay building bricks in super structure above plinth level- 1st class bricks in cement mortar 1:6 (1 cement :6 sand) complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Half brick work using common burnt clay building bricks in super structure above plinth level- 2nd class bricks in cement mortar 1:4 (1 cement :4 sand) complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden batterns and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4mtrs.and removal of the same for in-situ-reinforced concrete and plain concrete work in:-

Foundation, footings basis of columns etc. and mass concrete complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Columns, pillars, posts and struts Square, rectangular or polygonal in plan complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Sides & Sofits of Beams cantilevers girders lintels window sills, cornices, arches corbelling including curved surfaces where ever required sides and soffits of beams haunchings cantilevers bressumers and lintels upto all depths complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Flat surfaces such as soffits of suspended floor, roof, landings etc complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Stair cases with sloping or stepped soffits excluding landing complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Edges of slab and breaks in floor upto 200 mm thickness complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Vertical surfaces such as walls (any thickness) partitions and the like i/c attached pillasres buttresses,plinth & string courses and the like complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Providing Mild steel /Tor steel reinforcement for RCC work including bending, binding and placing in position complete upto floor two level (tor steel) complete in all respect including all leads and Lifts as per the direction and satisfaction of Engineer-In-Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, framed and fixed in position of 1st class M.P teak wood complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing & fixing panelled glazed or panelled & glazed shutters for doors windows and clerestory windows including black enamelled iron butt hinges with necessary screws in 1st class M.P teak wood complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

P/F 12 mm thick prelaminated board make green ply/ CenturyPly wood both side bwp phenol bonded exterior/interior grade panalled shutters with frame of first class deodar wood for doors including bright finished/black enamelled iron butt hinges with necessary screws 40mm thick frame complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws.40 mm thick- 1st class M.P teak wood complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing 19mm thick water proof commercial board make Bhutan/ Green/ Vergo board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing 19mm thick Commercial Board make Bhutan/ Green/ Vergo board water proof shutters for up boards i/c fixing with nickel plated piano hinges with screws etc complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing 1.00mm thick coloured or plain lamination sheet (sunmica) make Marino/ Equ. on boards/ ply wood sheets with approved adhesive and nails etc complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

P/F ply wood lining with butt jointing and nails make Bhutan/ Green/ Vergo board complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge. (frame work and cover fillets to be measured and paid separately)- 6mm thick

P/F aluminium handle anodised transparent or dyed to required shade with necessary screw complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

P/F aluminium tower bolt (barrel type) anodised transparent or dyed to required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing anodised aluminium sliding door bolt anodised colour and shade with nuts and bolts complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge. 250x16 mm

Prokviding and fixing 65x35mm.special quality bright finished brass cup board locks or wardrobe locks with six levers including necessary screws etc. complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge. (Indian make of approved quality)

Providing and fixing 100mm bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing M.S. hooks and eyes complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge. - 150 mm

Providing and fixing 12mm thick 150mm wide pelmet with 25 mm diametre wooden curtain rods and brackets including fixing 25x3mm M.S. flat at 10 cm. Long and plugs etc.complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge. 1st class M.P Teak wood.

Providing and fixing 10 mm thick anti skid water proof stain and impact resistant heavy duty vetrified tile Simpolo/ Nitco/ Kajaria/ Rak or equivalent 600x600 mm laid over 12mm thick bed of cement mortar 1:3(1 cement:3 sand) jointed with cement slurry mixed with pigment to match the shade of the tile complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and laying Non slippery spartic ceramic tiles 5.5mm (Five point five milimetres) thick Simpolo/ Nitco/ Kajaria/ Rak or equivalent in flooring 300x300mm (Three hundred into three hundred treads of steps laid on a bed of 12mm (Twelve milimetres) thick cement mortar 1:3 (One cement : three sand) finished with flush pointing in white cement complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and laying granite stone of superior quilitity Lakha/ Black make in Kitchen self flooring 20 mm (average thickness base of cement mortar 1:3(1cement: 3sand) laid over and jointed with gray cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete 20mm thick complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

White glazed tiles 6 mm thick Simpolo/ Nitco/ Kajaria/ Rak or equivalent in skirting, reser of steps and dado 12 mm thick bed of cement mortar 1:3 ( 1 cement: 3 sand) and jointed with cement slurry complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing 0.60 mm thick prepainted steel sheet Tata (Durashine) make colour (Red/Sky) in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 micron over 5 mocron primer coating to back coat of polyster of 5 micron over 5 micron primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer in charge.

Providing and fixing ridges or hips 60 cm overall with 0.63 mm thick prepainted steel sheet Tata (Durashine) make colour (Red/Sky) in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of 20 micron over 5 mocron primer coating to back coat of polyster of 5 micron over 5 micron primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer in charge.

Providing and fixing valleys 90 cm overall with 0.63 mm thick prepainted steel sheet Tata (Durashine) make colour (Red/Sky) in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of 20 micron over 5 mocron primer coating to back coat of polyster of 5 micron over 5 micron primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer in charge.

Providing and fixing flushing 38cm overall with 0.60mm thick prepainted sheet Tata (Durashine) make colour (Red/Sky) in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia meter & prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)

Providing and fixing on wall face PVC (D-plast) rain water pipes of working pressure not less than 4.5kg/sqm including filling the joints with approved adhesive complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge. 100 mm dia .

Providing and fixing on wall face PVC (D-plast) accessories for rain water pipes including filling the joints with approved adhesive complete- plain bend 100 mm dia .

Providing and fixing MS holder bat clamps of approved design to CI or PVC pipes embeded in cement blocks 10x10x10 cm of 1:2 :4 mix (One cement: 2 sand: 4 graded broken/crushed stone aggregate 20mm nominal size)and cost of cutting holes and making good the wall etc. complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge. 100 dia PVC pipes

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

In gratings framed guard bars,ladders,railling,brackets and similar works complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing MS grill SS 304 Grade of required pattern in window frames with MS flat, square or rounded bars with round headed nuts and bolts-plain grill complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Applying priming coat over new wood and wood based surfaces Asian make after and including preparing the surfaces of all dirt, dust and other foreign matter and sand papering and knotting with ready mixed paint brushing wood primer pink complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Painting two coats Asian make (excluding priming coat) on new wood and wood based surfaces with enamel paint white paint brushing to give an any shade including cleaning the surfaces of all dirt, dust and other foreign matters sand papering and stopping complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Applying priming coat Asian make on new concrete masonry/ asbestos/ cement/ plastered surface after and including preparing the surface by throughly cleaning oil, grease, dirt , dust, and other foreign matter and sand papering as required with ready mixed primer complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Painting two coats Plastic Emulsion (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an any shade including cleaning the surfaces of all dirt, dust and other foreign matters-enamel paint white complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

15 mm thick cement plaster in single coat on rough sides of brick/concrete/ stone walls for interior plastering upto floor two level including internal rounded angles chamfers, and or rounded angles not exceeding 80 mm in girthand finished even and smooth.- cement mortar 1:6 ( 1 cement: 6 sand) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Applying birla white wall care putty over plaster surface after throughly brushing the surface free from mortar drops, dust, loose materials and other foreign matter sand papered smooth to give final matter finish to the surface complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Applying priming coat Asian make on new concrete masonry/ asbestos/ cement/ plastered surface after and including preparing the surface by throughly cleaning oil, grease, dirt , dust, and other foreign matter and sand papering as required with ready mixed primer complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Wall painting two coats with premium emulsion Asian make of approved brand and manufacturefor interior grade on on un-decorated wall surface to give an even shade after throughly brushing the surface clean of all dirt, dust, loose pieces of scales and also including preparing the surface even and sand papered smooth including applying of putty as required for metling the surfacepriming coat with distemper primer complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing under layer for plinth protection of 75mm (Seventy five milimetres) thick(un-consolidated)bed of dry brick/stone aggregate 40mm(Forty milimetres)nominal sizes well rammed and consolidated and grouted with fine sand including preparation of ground complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing plinth protection 50mm (Fifty milimetres) thick cement concrete 1:3:6 (One cement: Three sand: Six graded crushed stone aggregate 20mm(Twenty milimetres) nominal size) including finishing the top surfaces of concrete smooth, complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Construction course rubble hammer dressed ‘U’ shape open surfaces drain with side wall 15x23cms (Fifteen into twenty three centimeters) in cement mortar 1:6 (one cement :six sand) and inside plastering with cement plaster 1:3 (one cement :three sand) including earth work and laying 10cm (Ten centimeters) cement concrete in 1:5:10 (One cement: five sand: ten graded) crushed stone aggregate 40mm(Forty millimeters) nominal size and 7.5cm (Seven decimal five centimetres)cement concrete 1:2:4 (One cement: two sand: four graded) crushed stone aggregate 20mm(Twenty millimeters) nominal size and finished with a floating cost of neat cement complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing wall hung double symphonic "P" or "S" Trap WC pan (Make:-Cera/Hindware/ Jaquar) (two piece) Complete in all respect. With built in 10 litr capacity of required shade complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing 10 litr vitreous china low level flushing cistern wall hung of (Make:-Cera/Hindware/ Jaquar) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing plastic seat cover solid type (Make:-Cera/Hindware/ Jaquar) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing vitreous china wash basin (Make:-Cera/Hindware/ Jaquar) with single hole for piller tap with CI or MS brackets painted white including cutting holes and making godd the same but excluding fitting 630X450mm complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing vitreous china pedestal for wash basin (Make:-Cera/Hindware/ Jaquar) complete recessed at back for the reception of pipe fittings complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing PVC waste pipe 32mm nominal dia make Finolex for wash basin and sink complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing M.I. Union for wash basin or sink 40mm make Finolex complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing kitchen sink with CI, SS or MS brackets, painted white make Cera/Prestige including cutting holes in walls and making good the same but execluding fittings 610X510X200mm complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing CP Towel rail 750X20mm make Jaquar complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing 450X600mm bevelled edge mirror of reputed make mounted on AC sheet and fixed with brass screws complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing 600X120mm glass self etc complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing chromium plated brass soap dish with brass brasket make Jaquar complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing CP concealed stop cock 15mm dia (Heavy duty) Jaguar make for jet system complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing CP 15 mm dia long nose tap make Jaquar Heavy duty) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing CP short body bib tap 15mm dia make Jaquar Heavy duty) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing CP mixture long nose tap 15mm make Jaquar Heavy duty) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing CP angle valve make Jaquar complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing PVC connection 15mm dia (Superior Quality) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing CI (Heavy duty) floor trap of self cleaning design with sand cast iron screwed down or hinged grating with out vent arm complete i/c cost of cutting and making goods the walls and floors complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing CI floor trap of self cleaning velocity 50mm Finolex Make complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing 100mm dia CP grating for Anti cockroach Floor Trap Finolex Make complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing spray flushing jet for double syphonic WC seat of Jaquar make complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing PVC pipe Finolex Make of following dia complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing PVC fitting Finolex Make of following dia complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Door bend

Plain bend

loose collar

Single equal branch tee

100mm X 100mm

75mm X 75mm

Plain tee

100mm X 100mm

75mm X 75mm

Providing and Fixing corrosion resistant G.I. pipe of following dia (H/Class) of Tata/ Jindal make complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing PVC storage Tank 1000 litrs Sintex Make complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing Shower in superior quality Long body Jaquar make complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Wiring for light point/ fan point/ Exhaust fan pt/ call bell pt/ with 1.5 Sq. mm PVC insulated heat resistant flame retard (HRFR) and low smoke single core (flexible) copper conductor cable in PVC conduit pipe and earthing the light point with 1.5 Sq. mm HRFRLS/PVC insulated single core copper conductor cable (Make:- Havells/Anchor/Bajaj & L&T) as required .Group C complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Wiring for light plug with 2x1.5 Sq.mm PVC insulated heat retardent (HRFR) and low smoke single core (flixible) coppe rconducter cable in surface/recessed PVC conduit along with 1 Nos. 1.5 Sqmm HRFRLS/PVC insulated single core copper conductor cable (Make:- Havells/Anchor/Bajaj & L&T) for earthing as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supplying and fixing metal box of 100mmX100mmX60mm deep (nominal size) on surface/ recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 6pin 5/6 amps,modular type switch connections painting etc asw required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

200mmx250mmx100mm deep

180mmx100mmx60mm deep

100mmx100mmx60mm deep

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable (Make:- Havells/Anchor/Bajaj & L&T) in surface/recessed steel conduit along with 1 No. 4 sq. mm. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

2x1.5sqmt.

2x2.5 sqmt

Wiring for circuit/sub-main with 4x6 sq. mm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable (Make:- Havells/Anchor/Bajaj & L&T) in surface/recessed PVC conduit along with 2 No. 6 sq. mm(4x6+2x6). HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Wiring for circuit/sub-main with 4x10 sq. mm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable (Make:- Havells/Anchor/Bajaj & L&T) in surface/recessed PVC conduit along with 2 No. 10 sq. mm(4x10+2x10). HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supplying and fixing 15/16 Amp. Modular type switches (Make:- Havells/Anchor/Bajaj & L&T) the existing switch box/cover including connection etc. as required (S.P. 15/16 Amp one way socket on switch, porce lain base/ Modular type complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supplying and fixing 6 pin 15/16 Amp. Modular type socket outlets (Make:- Havells/Anchor & L&T) on the existing switch box/cover including connection etc. Modular type as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supplying and fixingfollowing way triple way pole and neutral sheet steel MCB distribution board 415 volts (Make:- Havells/Anchor & L&T) on surface/ recess with provission to mount 8 module incomer 2 module sub incomer and SP MCB as outing complete with tinned copper bus bar, wire set neutral link earth bar dinbar, detachable gland plate cable, identification labels inter connection phosphatized and powder painted including earthing etc. as required ( double door 2+12way ( 8+6+36) type complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supplying and fixing following rating ,four pole (three pase and neutral) ,415 volts residual current circuit breaker (RCCB) (Make:- Havells/Anchor & L&T) having a sesivity current up to 300 miliampers in the existing MCB, DBcomplete with connection testing and commissioningas required. 63 Amps. cat-A complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supply & erection of 40/50/63 amp. Rating 10 KA Breaking MCB IbL 240 volts (Make:- Havells/Anchor & L&T) C curves moviature circuit breaker of following poles in the exoisting MCB DD complete triple pole & neutral cat-A complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Earthing with GI earthing 4.5 mtrs long 40mm dia including accessories and providing masonry enclosure with copper plate having locking arrengement and watering pipe etc. (but without charcoal coke and salt ) complete as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Extra for using salt & charcoal for pipe earth electrode complete as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supplying and laying 6 SWG GI wire of 0.50mtr below ground level of earth electrode conductor including soldering etc. complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supply & erection of 6 to 32 amp. Rating 10 KA Breaking capacity 240 volts C curves miniature circuit breaker of single poles category -A in the existing MCB DD with connection as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supplying and Fixing sheet metal bus bar chamber suitable for 63 Amp. 415 volts capacity with 4 Nos copper strip bus bars each of length 300mm and cross sectional area (16mmx3.17mm) enclosure made from 1.6mm thick MS sheet having overall dimentions (380x350x150mm) nominal with all accessries including connection earthing the body etc. as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing following rating and breaking capacity MCCB (Make:- Havells/Anchor & L&T) in the existing cubical panel board including drilling holes in the cubical panel making connections as required (100 Amp -16 KA) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supply and errection of wall mounted metal board for switch gear mounting of suitable size, with permissible variation in size of plus minus 5 mm ,welded fram work made on MS angle iron 35x35x6mm thick dually welded completewith 2.80 mm thick MS sheetfixid with hinges as open size front complete with locking arrangment including painting and bounding to the existing earth a required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing,installation, testing and commissioning of ceiling fan of Bajaj/ Havells/Usha/ Philips/ Crompton greaves make with regulator,including wiring the down rod of standared length 9Up to 30 CM)with 16/0.20 mm twin twisted flexible cotton braided, copper cable including providing and fixing phenolic laminated sheet cover on the fan box and earthing as required. Ceiling fan 1200 mm sweep.category-A complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing,installation, testing and commissioning of exhaust fan of Bajaj/ Havells/Usha/ Philips/ Crompton greaves make of following size in the existing opening in cliding making the hole to suit the size of the abobe fan making good the damaged connection testing and commissioning etc. as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supplying and fixing of fancy wall bracket containng thread type CFL lamp holder (Make:- Havells & Philips) of all size and shape complete with all acessories but excluding CFL lamp including making connection as required. Fixed type wall bracket 150 dia , single lamp. (Category-A) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supplying and fixing of wall bracket containng thread type CFL lamp holder (Make:- Havells & Philips) of all size and shape complete with all acessories but excluding CFL lamp including making connection as required. Mirror light 460mm single lamp. (Category-A) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supplying and Fixing call bell/buzzer suitable for D.C/A.C single phase 230 volts (Make:- Havells & Philips) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Supplying and fixing of surface/ recess mounting ceiling fitting of all size and shape, containing 1No. Thread type CFL lamp holder (Make:- Havells & Philips) complete with all acessories but excluding CFL lamp including making connection as required. Ceiling fitting surface type (Category-A) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing fuse unit 100 Amp. (Make:- Havells/Anchor & L&T) with nut and bolt complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and Fixing CFL lamp (11watt) (Make:- Havells & Philips) including testing complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing,installation, testing and commissioning of pre-wired fluorescent tube fitting complete with copper ballast starter and capacitor but excluding fluorescent tube rod suitable to operate on 240 volts single phase AC supply directly on surfaces with copper wiring as required tube fixture 1x40 watt per spex type category-A complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing CFL post top lantern (Make:- Havells/Anchor & L&T) of following capacity cost aluminium spigot spun aluminium canopy, opal acrylic diffuser, complete, with all accessories but excluding CFL lamp including making connection, testing etc. as required. gate post top lantern-CFL 2x11 watt. following rating and breaking capacity MCCB in the existing cubical panel board including drilling holes in the cubical panel making connections as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge. (100 Amp -16 KA.

S/F folllowing way single pole and natural sheet MCB distribution board 240 volts (Make:- Havells/Anchor & L&T) on surface/ recess complete with laminated copper bus wire set natural link earth war, din-bar, detachable gland plate planking plate, cable indentification labels interconnection, phophatized and powerpainted, including earthing etc. as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and fixing of 25mm dia PVC conduit along with the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required (D-Plast/ Finolex make) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

Providing and installation of stationary storage type electric water heater (Geysor) of various size bymean of expension- bolt with nuts and washer, including embedding of expansion boltin the wall,providing and fixing of non . return valve, dead weight safety valve ,2 No CP connection rod 18"longmaking good the damaged ,electrical connection, safety valve connection , testing and commissioning etc as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge. (Havells/Racold & Bajaj make with autocut.)

10 Liter water heater Cat A

25 Liter water heater Cat A

Providing and installation 2MT Voltas Vertis Plus Split Air Conditioner with 5 star rating including connection, testing and commissioning etc as required complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.

PANKAJ KUMAR

Sushant Puri