Construction of Executive Engineer and Assistant Engineer office Building at Jaisinghpur Distt. Kangra (HP)

Amount

Excavation in foundation and trenches in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, pick jumper work, blasting work both in soft and hard rock, chiseling / wedging out of rock (Where blasting is prohibited) or any other mixed variety of soil including shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) up to any heights / depths or any quantum of water including slush which may arise during de-watering, removal of slush and stacking the serviceable and un-serviceable material clear from the edge of excavation and then returning the stacked soil in 15cm (fifteen centimeter) layers where required into plinth and side of foundation etcetraetera, consolidating each deposited layer by ramming & watering and then disposing of all surplus un-serviceable excavated earth as directed within all leads and lifts, by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machineries and disposed material to be neatly dressed and leveled as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:3:6 (one cement is to three sand is to six graded crushed stone aggregate 40 mm (forty millimeter) nominal size) and curing complete excluding the cost of form work in foundation and plinth as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetraetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Foundation, footings,bases of columns etcetraetera and mass concrete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetraetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etcetraetera upto any thickness as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetraetera with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Beams, cantilever, girders, lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depth and in all heights from floor as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetraetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Columns, pillars, posts and struts , square rectangular or polygonal in plan as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetraetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Circular Columns, pillars, posts and struts square rectangular or polygonal in plan as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetraetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Stair cases with sloping or stepped soffits excluding landing, as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetraetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls up to all width and heights as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetraetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters, buttresses, plinth and string courses and as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying mechanically mixed cement concrete 1:6:12 (one cement is to six sand is to twelve graded stone aggregate 40mm (forty millimeter) nominal size) and curing complete excluding cost of form work in foundation and plinth as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement is to four sand is to eight graded crushed stone aggregate 40 mm (forty millimeter) nominal size) and curing complete excluding the cost of form work in foundation and plinth as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Stone filling with hard stone of approved quality dry hand packed tightly under floor. as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Squared rubble masonry coursed with hard stones of approved quality in foundation and plinth including raking out joints in cement mortar 1:6 (one cement is to six sand) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M-twenty) design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty newton per square millimeter) with cement contents not less than 330 kgs (three hundred thirty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in Foundation footings, bases of columns and the like and mass concrete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 ( M-twenty) design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty newton per square millimeter) with cement contents not less than 320 kg (three hundred twenty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in suspended floor ,roofs , landings , shelves and their supports balconies, beams ,girders , bressumers and cantilevers up to all floor level as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty Newton per square millimeter) with cement contents not less than 320 kg (three hundred twenty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in columns ,pillars, post, struts and the like and mass concrete up to all floor level, as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 ( M-twenty) design mix to obtained the minimum Compressive strength of 20N /mm2 (Twenty Newton per square millimeter) with cement contents not less than 320 kg (three hundred twenty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in stair case (except spiral stair cases) including landings etcetraetera up to floor all levels as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the minimum compressive strength of 20 N/ mm2 (Twenty Newton per square millimeter) with cement contents not less than of 320 kg (Three hundred twenty kilogram) per cubic metre, mechanically mixed and vibrated including curing complete for reinforced concrete work in Chhajjas not exceeding 10cm (ten centimeters) thickness upto floor all levels including finishing the exposed surface with cement mortar 1:3 (One cement : Three sand) to give a smooth and even surface including centering/ form work and curing complete but excluding the cost of reinforcement for reinforced concrete work up to all floors level as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 ( M-twenty) design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty Newton per square millimeter) with cement contents not less than 320 kg (three hundred twenty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete including cost of form work but excluding reinforcement for reinforced concrete work in moulding as in cornices windows, sills etcetraetera exceeding upto any girth, upto floor all level as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying plain cement concrete grade M-20 (M-twenty) design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty newton per square millimeter) with cement contents not less than 330 kgs (three hundred thirty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated & curing complete excluding cost of form work in foundation and plinth as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete M-20 ( M- twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty Newton per square millimeter) with cement contents not less then 320 Kg (three hundred twenty kilogram) per cubic metre and curing complete excluding cost of form work and reinforcement for reinforced concrete work in walls ( any thickness but not less than 0.10 (zero point ten) Metre thickness) including attached pilasters buttresses, plinth and string courses etcetraetra from top of foundation up to floor all levels as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing Tor steel reinforcement of TATA TISCO/SAIL for RCC work including bending, binding and placing in position complete up to all floor levels with cost of binding wire including carriage of material within all leads, lifts and other incidental and as per the direction of the Engineer-In-Charge .The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying Damp Proof Course with 100mm (one hundred millimeters) thick cement concrete 1:2:4((one cement: two sand: four graded crushed stone aggregate 12.5mm (Twelve decimal five millimeters nominal size) and curing complete, as required at site as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Applying a coat of hot bitumen (mexphalt 80/100 (Eighty/Hundred)/VG-10 using 1.70 Kgs. (one decimal seven zero Kilogram) per square metre On Damp Proof Course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Half brick masonry using second class common brunt clay building bricks in super structure above plinth level to floor all levels in cement mortar 1:3 (one cement is to three sand) with hoop iron such as two Nos 6/8 mm dia bars in Z shape crossing each other shall be proceeded at the interval of 90-100 cm horizontally as well as vertically to strength the masonry work complete. as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Second class brick work using common burnt clay building bricks in superstructure above plinth level to floor all levels in cement mortar 1:6 (one cement is to six sand) as per specifications,approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Second class brick masonry wall having overall thickness of 28 cm (twenty eight centimetre) using common burnt clay building bricks in superstructure upto floor all levels with hoop iron and cross tiles 8 mm (eight millimetre) dia steel bars in Z shape, laid in cement mortar 1:3 (one cement is to three sand) including two number 11.5 cm(eleven decimal five centimetres) thick wall having internal cavity of 5 cm (five centimetres) wide (Area of only one face will be measure for payment) complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Second class brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:6 (one cement is to six sand) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Half brick masonry using second class common brunt clay building bricks in sub structure above plinth level to floor two levels in cement mortar 1:4 (one cement is to four sand) as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing anodised aluminium frames for door, window, ventilators and partitions aluminium section 127x44.45x3.18/101.60 x 44.45 x 3.18 mm (one hundred twenty seven into forty four decimal forty five into three decimal eighteen millimetre oblic one hundred one decimal sixty into forty four decimal forty five into three decimal eighteen millimetre) or as specified of Jindal/Hindalco with extruded built up standard tubular and other sections of approved make conforming to IS :733 and IS: 1285 anodised transparent or dyed to required shade according to IS :1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etcetraetra. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleat angle, aluminium, snap beading for glazinge/panelling, C.P. brass/stainless steel screws all complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing M.S. channels frames 75x40x4mm (Seventy five into Forty into four millimeter) door/ windows/ ventilator frame and M.S. flat 75x4mm (Seventy five into Four millimeter) combination welded together to make a one frame as per design, drawing, including hinges, jambs, beads if required, threshold of M.S. angles 50x25 (fifty into twenty five millimeter) welded/ rigidity fixed by mechanical means, hinges with split end tails to each jambs with a provision of locking arrangements, shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of surfaces as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing everest designar fibre board ceiling tiles size 600mm x 600 mm (six hundred into six hundred millimetre) over readymade powder coated metal sheet section frame work 600 mm c/c(six hundred millimetre centre to centre) grid suspended form ceiling as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing anodised aluminium shutters for doors, windows and ventilators including providing and fixing hinges/pivots and making provisions for fixing of fittings where ever required including the cost of PVC/neoprene gaskets as required (fittings and glazing/panelling shall be paid for separately) for doors section 150x44.45x3.00/101.60 x 44.45 x 3.00 mm/83.50x44.45x3.00 mm (one hundred fifty into forty four decimal forty five into three millimetre oblic eighty three decimal fifty into forty four decimal forty five into three millimetre) window and ventilators section 83.50x44.45x25x2.40 mm (eighty three decimal fifty into forty four decimal forty five into twenty five into two decimal forty millimetre) or as specified of Jindal/Hindalco with extruded built up standard tubular and other sections of approved make conforming to IS :733 and IS :1285 anodised transparent or dyed to required shade according to IS :1868. (Minimum anodic coating of grade AC 15) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etcetra. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleat angle, aluminium, snap beading for glazing/panelling, C.P. brass/stainless steel screws all complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 12mm thick (twelve milimetre) thick pre-laminated board both side water proof particle board of Action/Tesa/Centaury/Kitlam/Green ply as per approved shade bwp phenol bonded exterior/ interior grade for inphil pannel of door shutters and fixed with necessary screws etcetraetera complete as per specification, approved drawing , design or as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing to existing door frames 30mm thick factory made PVC panneled door shutters consisting of frame made out of (Mild Steel) tube of 19 gauge thickness of size 19mmx19mm for style and 15mmx15mm (Mild Steel) square tube for top, bottom & Lock rail (Mild Steel) frame shall have a coat of steel primer and covered with 5mm thick PVC solid sheet heat moulded "C" channel of size 30mm thickness, 70mm width out of which 50 (Fifty millimetre) shall be flat and 20mm (Twenty millimetre) shall be tappered in 45 degree (Forty five degree) angle on either side forming style and 5mm (Five millimetre) thick, 95mm (Ninety five millimetre ) wide, out of which 75mm (sventy five millimetre) shall be flat and 20mm (Twenty millimetre) PVC sheet should be tapered in 45 degree (Forty five degree) on the inner side to frame top and bottom rail and 115 mm (one hundered millimetre) wide PVC sheet out of which 75mm (Seventy five millimetre) shall be flat and 20mm (Twenty millimetre) shall be tapered on both side to frame lock rail, top and bottom and lock rail sahll be provided either side of the pannel 10mm (Ten millimetre) thick,20mm (Twenty millimetre) widecross PVC sheet be provided as gap insert for top rail and bottom rail panneling of 5mm (Five millimetre) thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the style of rails, joints mitred and jointed with solvent cement adhesive including fixing of PVC shutter with existing frame with M.S. butt hinges 100x51x1.90mm (One hundred into fifty one into one point nine zero millimetre) size with necessary screws etcetraetra complete as per specification, approved drawing , design or as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing glazing of Modi Guard/Saint Gobian in aluminium door, window, ventilator shutters and partition etcetra with PVC/neoprens gasket Glazing with glass pane of 5 mm (five millimetre) thickness (weight not less than 12.50 kg/ sqm. (Twelve point five zero kilogram per square metre)complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing glazing of Modi Guard/Saint Gobian in aluminium door, window, ventilator shutters and partition etcetra with PVC/neoprens gasket etcetra.Glazing with glass pane of 6mm thickness (weight not less than 15.00 kg/ sqm (fifteen kilogram per square metre) complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing glazing of Modi Guard/Saint Gobian in aluminium door, window, ventilator shutters and partition etcetra with PVC/neoprens gasket Glazing with froarted glass pane of 5 mm thickness (weight not less than 12.50 kg/ sqm. (Twelve point five zero kilogram per square metre)complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing fly proof stainless steel (grade 304) wire gauge of 0.5 mm (zero desimal five millimetre) diametre wire and 1.4 mm(one point four millimetre) aparture in both side complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing aluminium 8 mm (eight millimetre) thick grill anodised powder coated pattern to existing window/ventilatior with 80mmx80mm (eighty into eighty millimetre) panels holes with 25x8mm thick(twenty five into eight millimetre) aluminium flat in windows and ventilators including fixing with aluminium screws or bolts and nuts complete in alluminium channels base frames (Aluminium channels base frames to be measured and paid for separately(only weight of grill to be measured for payment) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 19mm (Nineteen millimeter) thick commercial board water proof of kitply / Dura ply/century ply,Marino ISI marked for cup board shutters, shelves. Back side of cup board shall have 8 mm (eight millimetre) thick water proof ply. All the exposed portion of board shall have 6 mm (six millimetre) thick hard wood edging. The shutter from outer side shall be finished with 1mm (one millimetre) thick lamination of Century / Green ply/ Action Tesa of approved shade including hinges, handle,knob megnatic catcher complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals (outer face to be measured for payment only). The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 25mm (twenty five millimeters) thick water proof commercial board shutter of Centuary ply (ISI marked) in SDB/fire fighting shutter with 6 mm (six milliletre) thick hard wood edgenig and 1mm thick laminated from out side of approved shade and PGI sheet lining inside including hinges, handle,knob & neccessary fitting complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 25mm (Twenty five millimetre) diametre stainless steel curtain rod including brackets , clamps etcetra complete in all respect as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing magnetic catcher in cup board shutters with necessary screws etcetraetera complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.Government.

Providing and fixing 65x35mm (Sixty five into Thirty five millimeter) special quality bright finished brass cup-board locks or ward robe lock, with six levers including necessary screws etcetraetera complete (Indian make of approved quality) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing anodized aluminum sliding door bolt anodized transparent or dyed to required colour and shade with bolts, nuts and screws etcetra complete 300 X 16 mm (three hundred into sixteen millimeter) size as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetraetera complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

200 X 10 mm (two hundred into ten millimeter) size

150 X 10 mm (one hundred fifty into ten millimeter) size

Providing and fixing aluminum handles anodized transparent or dyed to required colour and shade with necessary screws etcetraetera complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

150 mm (one hundred fifty millimeter) size

100 mm (one hundred millimeter) size

Providing and fixing aluminium anodized transparent or dyed to required shade and colour hooks and eyes with necessary screws etcetraetera complete 250 mm (two hundred fifty millimeter) size as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimeter)size double acting hydraulic floor spring hinges bright finishes of approved brand ISI Marked with necessary screw etcetra complete including entire carriage of material within all lead, lifts and other incidentals as per specification approved drawing, design and as directed by the Engineer- in-charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 20mm (twenty millimetre) granite stone in flooring,single slab in treads of steps with semi round nosing in skirting, riser of steps and landing 20mm(twenty millimetre) (average)thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 8 mm (eight millimetre) thick HDF laminated flooring of ActionTesa/LG/Vista laid over sub base of cement concrete / RCC slab to be paid separately complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying automatic hydraulic compressed and polished Precast terrazzo tiles of ISI marked No.1237 of size 300 x 300x 25mm thick vibro compacted of NTC in 50% white & 50% grey cement with chips 55% white 15% each Marron, Yellow and dark green of size 0,B,2B laid in floors, treads of steps, ramp and landings laid on a bed of 25mm thickness of cement mortar 1:6(1 cement : 6 Sand) jointed with cement slurry mixed with pigment to match the shade of tiles (Wherever required) including rubbing , polishing Complete and of approved shade as per specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying double ultra charged matt finish vitrified tiles of size 600 x 600mm of Kajaria/Eternity/Nitco/simpolo/Bell/Rack/johnson of specified shade in floors, treads of steps and landing laid on a bed of 12mm. thick cement mortar 1:3(1 cement: 3 sand) jointing with cement slurry mixed with pigment to match the shade of tiles complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and Laying 20 mm (twenty millimeter) thick polished Baroda green marble with semi/ round nosing laid over 20mm thick base in cement mortar 1:3 including Jointing with white cement mortar (1:2) 1 white cement :2 marble dust with an admixture of pigment to match the shade of marble including cutting moulding and polishing complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying ceremic tiles antiskid non slippery of Kajaria/Nitco/Orient Bell/somany/ AGL in flooring (300*300) mm (Thirty into thirty millimeter) size laid on a bed of 12mm thick cement mortar 1:3 finished with flush pointing in white cement slurry mixed with pigment to match the shade of tile including rubbing/nosing/moulding and polishing complete as per specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government..

Providing and laying 300x300x25mm labrodor design (rainbow series)of NTC tile flooring 20mm average thick base of cement mortar 1:4 (1 cement : 4 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish finish as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 60mm (sixty millimeter) thick inter locking paver blocks of NTC laid over base of 25 mm cement mortar 1:4 (1 cement : 4 sand) and jointed with neat cement slurry to match the shade of block including cuttining , rubbing & nosing complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 40mm (forty millimeter) thick framed panelling with 8mm (eight millimetre) thick teak ply over 50x31 mm soft wood frame work at 600 mm c/c (centre to centre) with decorative teak wood beading over teak ply of size 25x12mm having moulding on both side . Cornice / edging in the top of paneling to be finished 55x30mm teak wood beading or as specified complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying Precast terrazzo tiles hydraulic compressed and polished ISI marked IS No. 1237 (50% white 50% grey cement) in white , Yellow, green and maroon chips of D,B,2B size of NTC with 55% white 15 % each maroon, yellow and dark green in skirting and risers of steps not exceeding 30 cm in height and laid with 10 mm thick cement plaster 1:3 (1 cement: 3 sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing polishing, nosing moulding and cutting complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying of Kajaria/Eternity/Ristle/Nitco/Bell/Rack/ Simpolo double /ultra charge matt finish vetrified tiles of approved shade in skirting, risers of steps and dados on 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 300x450mm (Three hundred into four hundred fifty millimetre) cermic glazed tile of Kajaria/Eternity/Ristle/Nitco/Bell/Rack/ Simpolo/ Johnson in skirting, riser and dado laid on a bed of 12 mm thick cement mortar 1:3(1 cement :3 sand) finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tile complete including cutting, rubbing and nosing as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 50mm (Fifty millimetre) cement concrete flooring 1:2:4 (1 cement: 2 sand :4 stone aggregate )20mm nominal size laid one layer finished with floating coat of neat cement as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing prepainted steel sheet roofing of Tata Dura shine/Reliance/ Jindal over steel trusses of 0.60 mm thickness (ISI marked Z-120) over steel truss prepainted galvanized steel and hot dipped metallic zinc coat sheet with top coat of regular modified polystar (RMP) organic coating of 20 (twenty ) micron over 5 (Five) micron and back coating of polystar 5 (five) micron over 5 (five) micron primer coating including fixing with prepainted ironJor L hooks, bolts , nuts 6 mm (six millimeter) dia with prepained limpat and rubber washers complete with all accessories as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all with 0.60mm (Zero decimal Six zero millimeters) thick pre-painted steel sheet of Tata Dura shine/Reliance/Jindal ( Factory made) shall be having proper Gola / shape with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with pre-painted iron J or L hooks, bolts and nuts 6mm (Six millimeters) diameter with pre-painted G.I. limpet and bitumen washers complete with all accessories as required as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing valley 90cm (Ninety centimetre) over all of Tata Dura shine/Reliance/Jindal with 0.60mm (Zero decimal Six zero millimeter) thick pre-painted steel sheet with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (twenty) microns over 5 (Five) microns primer coating to back coat of polyester of 5 (Five) microrns over 5 (Five) microns primer coating including fixing with pre-painted iron J or L hooks, bolts and nuts with EDPM seal. The meterial supplied will be accompanied by test certificate & 20 years warrenty from company against the corrosion fading of colour & manufacture defects and further as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 300mm. (Three hundred millimeter) wide 300mm. (Three hundred millimeter) deep clear plain G.I. Sheet gutter of Tata/Sail fixed with bolts nuts and washers etcetra. including dome shape grating and making necessary connections with rain water pipe complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing M.S. ( Mild Steel) B.P. (Black plain) sheet 2.00 mm (two millimeter) thick in eaves boards/facia/soffits /ceiling including cutting, fixing, jointing with gas/electric welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured and paid for separately) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 150mm (oneHundred fifty milimetre) diameter on wall face P.V.C. (D-plast) rain water pipes 2.2mm ( Two decimal Two millimeter) thick of supreme/Finolex/Prince having working pressure not less than 4.50 kg /cm2 (Four decimal five zero kilogram) per square centimeter including filling the joints with approved adhesive complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing on wall face P.V.C. (D-plast) acessories of Supreme/Finolex/Prince/Astral for rain water pipes including filling the joints with approved adhesive complete as per H.P.P.W.D specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

150mm (One hundred fifty millimtre) diametere PVC Plain bend

150mm (One hundred fifty millimtre) diametere PVC shoe

Providing and fixing 150mm (one hundred fifty millimeter) diametre PVC clamps of approved design to PVC pipes embedded in cement concrete block 10cmx10cmx10cm (Ten centimeter into Ten centimeter into Ten centimeter) of 1:2:4 (One cement is to Two Sand is to Four graded crushed stone aggregate 20mm (Twenty millimeter) nominal size or fixing with steel screws etcetra complete including cost of cutting holes and making good the wall etcetraetera as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Steel work of TATA TISCO/SAIL welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint in beams, joist, channels, angle, tee, flat with connecting plates or angle, cleats as in main and beams, hip and jack rafter fixing in rafter, purlin connects to common rafter in trusses complete as per H.P.P.W.D specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying double coat water proofing treatment on terrace / depressed portion done with Dr. Fixit pidiproof over toilet area polymer modified cementitious coating consisting of cementitious powder and a polymer liquid. Water proof coating shall be done in two coats as follows. After laying the drain pipes, the floor concrete / slab shall be admixed with Dr. fixit pidi proof LW@200ml/50 kg bag of cement, if crack are found there at the junction or in between the slab then before applying Dr. Fixit Pidi proof LW, the junction of the wall/ Beams and slab shall be rounded using cement mortar of 1:5 admixed with Dr. Fixit Pidi Proof LM integral water proofing compound conforming to IS:2645 as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 50 mm dia stainless steel (Grade316) staircase railing made of hollow tubes, channels plates fixed with 35 mm dia SST baluster etcetra, including welding, grinding, buffing, polishing and making curvature and fitting the same with necessary stainless steel nuts and bolts complete complete as per specification approved drawing , design or as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing of 50 mm dia stainless steel hollow pipe hand rail slip resistant with round ended at two level at 75 cm and 90 cm in height. It shall be 30cm beyond the top and bottom having 25mm dia Stainless steel baluster welded to 50mm dia stainless steel pipe. the blauster shall be emended in cement concrete @ 60cm c/c complete as per specification, approved drawing , design or as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Painting two or more coats (excluding priming coat) withNerolac/Berger/Asian Paint on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters with enamel paint of approved shade as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Applying priming coat of Nerolac/Berger/Asian Paint/Shalimar paint over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matters with sand papering and knotting as required with ready mixed paint brushing wood pink primer as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Painting two or more coats(excluding priming coat) with Nerolac/Berger/Asian Paint on new wood and wood based surface with ready mixed enamel paint of approved shade brushing to give an even shade including cleaning the surface of dirt, dust and other foreign matters, sand papering and Knotting complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

6mm (Six millimeter) thick cement plaster in ceiling with cement mortar 1:3 (One cement: Three sand) for all heights as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

15 mm (Fifteen millimeter) thick cement plaster in single coat on rough side of brick/concretes/ stone walls for interior plastering up to all floor levels including arises, internal angles, chamfers and rounded angles not exceeding 80mm (Eighty millimeter) in girth and finished even and smooth with cement mortar 1:6 (One cement is to six sand) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

15 mm (Fifteen millimeter) thick cement plaster in single coat on fair side of brick/concretes/ stone walls for interior plastering up to all floor levels including arises, internal angles, chamfers and rounded angles not exceeding 80mm (Eighty millimeter) in girth and finished even and smooth with cement mortar 1:6 (1 cement : 6 sand) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

15 mm (Fifteen millimeter) thick cement plaster in single coat on fair side of brick/concretes/ stone walls for exterior plastering up to all floor levels including arises, internal angles, chamfers and rounded angles not exceeding 80mm (Eighty millimeter) in girth and finished even and smooth with cement mortar 1:5 (1 cement : 5 sand) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

20mm (twenty millimeter) thick Cement plaster in pattern with cement mortar 1:4 (one cementisto four sand) as shown in elevation / drawing upto floor all level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (Eighty millimeter) in girth and finished even and smooth as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

20mm (twenty millimeter) Cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (Eighty millimeter) in girth and finished even and smooth with cement mortar 1:4 (One cement is to four sand) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 12mm thick unistone cladding on wall surface side as on faces of Arch masonry walls with 12mm. thick cement plaster 1:3(1cement:3sand) and jointed with cement slurry including scaffolding etcetra. complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar dropping, dust, loose material and other foreign matters, sand papered smooth to give final matt finish to the surface complete. as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Finishing wall with weather proof exterior grade emulsion of approved shade (Apex of asian paint/ Nerolac paint) on undecorated wall surfaces (two or more coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matters etcetraetera including sand papering smooth complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Wall painting (two or more coats) with interior Acrylic washable emulsion paint of Asian/Nerolac paints and manufacture on un-decorated concerete/ stone /plastered wall surfaces to give an even shade including thoroughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for matting the surfaces as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Wall painting (two or more coats) with interior Acrylic emulsion paint of Asian paints and manufacture for interior grade on un-decorated concerete/ stone /plastered wall surfaces to give an even shade including thourhgly brushing the surfaces free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required for matting the surfaces as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Distempering (two or more coats) with dry distemper of Asian/Nerolac paint of approved shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing plinth protection with 40mm (forty millimeter) thick interlocking paver block of NTC and 23 cm dia half round RCC (Reinforced cement concrete) pipe for drainage purpose laid over 10cm (ten centimetre) thick cement concrete 1:4:8(one cement is to four sand is to eight graded stone aggregate 20mm(twenty millimeter) nominal size) for bedding and haunching of pipe as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 40 mm dia steel pipe grab bar at 78 cm height or as specified with M.S. plate complete as per detail drawing and position of seat/ wash basin and as per entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Brick bat filling for filter material in filter chamber as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 75mm diameter.P.V.C. pipe for inlet and outlet connection of Supreme/ Prince/ Finolex including fixing with approved adhesive etcetraetra complete The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 75mm diameter.P.V.C. cowl of Supreme/ prince/ Finolex including fixing with approved adhesive etcetra complete The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 455x610mm (four hundred fifty five into six hundred ten millimetre) light duty rectangular C.I. manhole cover with out frame weight not less than 23kg (twenty three kilogram) (single seal) as per specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana and all type of taxes imposed by the Government.

Providing and fixing 200mm (Two hundred millimetre) wide cast iron rungs with chequred or ribbed non slip surface including fixing in septic tank with 200mmx200mmx100mm (Two hundred milimetre into two hundred milimetre into one hundred milimetre) cement concrete 1:3:6 (One Cement: Three Sand: Six graded crushed stone aggregate 20mm (Twenty milimetre) nominal size) as per specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana and all type of taxes imposed by the Government.

Providing and fixing 150 mm (one hundred fifty millimetre) PVC single equal branch of required degree of Supreme/Finolex/Prince including fixing with approved adhesive complete. as per specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana and all type of taxes imposed by the Government.

Construction manhole with R.C.C. (Reinforced cement concrete) top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty millimetre nominal size) foundation concrete 1:4:8(One cement: Four sand: Eight graded crushed/broken stone aggregate 40mm(Forty millimetre) nominal size inside plastering 15mm (Fifteen millimetre) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty millimetre) nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred millimetre) and 500mm (Five hundred millimetre) deep, including C.I. (Cast iron) cover with frame (light duty single seal pattern -I) 455x610mm (Four hundred fifty five into six hundred and ten millimetre) internal dimensions. Total weight of cover and frame to be not less than 38 Kg (Thirty eight kilogram) weight of cover 23Kg (Twenty three kilogram) and weight of frame 15 Kg (Fifteen kilogram) with 200mm (Two hundred millimetre) thick walls of brick maronry using common burnt clay building brick in cement mortar 1:3 (one cement: three sand) as per specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana and all type of taxes imposed by the Government.

Construction manhole with R.C.C. (Reinforced cement concrete) top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty millimetre nominal size) foundation concrete 1:4:8(One cement: Four sand: Eight graded crushed/broken stone aggregate 40mm(Forty millimetre) nominal size inside plastering 15mm (Fifteen millimetre) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty millimetre) nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred millimetre) and1000 mm (one thousand millimetre) deep, including C.I. (Cast iron) cover with frame (light duty single seal pattern -I) 455x610mm (Four hundred fifty five into six hundred and ten millimetre) internal dimensions. Total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs (Twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 200mm (Two hundred millimetre) thick walls of brick maronry using common burnt clay building brick in cement mortar 1:3 (one cement: three sand) as per specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana and all type of taxes imposed by the Government.

Providing and fixing 455x610mm (four hundred fifty five into six hundred ten millimetre) C.I. manhole cover with frame weight not less than 38kg (thirty eight kilogram) the weight of cover 23 Kg (twenty three kilogram)and weight of frame 15 Kg (fifteen kilogram) complete as per specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana and all type of taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten milimtre) diameter on wall faces/ventilating pipe of P.V.C. of supreme/finolex/Prince/ (D-plast) pipes of working pressure not less than 4.50 kgs(Four decimal five zero kilograms) per square centimetre including filling the joints with aproved adhesive complete as per specification approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana and all type of taxes imposed by the Government.

Providing and fixing polythene aluminum polythene (P.E.) A.E P.E composite pressure pipe U.V. stabilized with carbon black conforming to I.S. 15450-2004 of Flow guard/ Kitec for water supply including clamps at one metre spacing, cutting, fixing and making good the walls etcetraetera; but excluding the cost of fittings (Internal work) pipes exposed on wall including filling the joints with approved adhesive complete and entire carriage of material with in all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

1620 (20 mm O.D.) pipe

12025 (25 mm O.D.) pipe

Making connection of glavanised mild steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipe complete and entire carriage of material with in all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing in trenches P.V.C. pipe of Supreme/ Finolex /Prince class “A” soil waste and ventilating pipe fixing with approved adhesive mixure complete 4.6mm (four point six millimeter) thick shall conform to IS No. 13592-92, It should be fire resistance, chemical resistance and should be able with stand temp upto 60⁰ call junction fitting shall conform to IS No. 14735-99 and shall be jointed to each other by a rubber ring/ push fit jointing system with a sealing ring and a rubber lubricant adhesive for PVC pipe / ventilation pipe type A within all leads, lifts and other incidentals as per approved specifications drawing, design and as directed by the Engineer- in-charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

110mm nominal bore/diameter.

150 mm nominal bore/diameter

Providing and fixing PVC clamps for PVC pipes fitting with steel screws and rawls plugs etcetra complete. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

150mm nominal bore/diameters.

110mm nominal bore/diameters

Providing and fixing P.V.C accessories Supreme/ prince/ Finolex for Sewerage pipe conforming to IS No. 14735-99 P.V.C. Plain bend including carriage of material with in all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

150mm diameter.

110mm nominal bore/diameter

Providing and fixing PVC heal rest of Supreme/ prince/ Finolex including fitting the joints with approved adhesive mixure complete The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. .

150mm nominal bore/diameter.

110 mm nominal bore/diameter

Providing and fixing P.V.C. collar of Supreme/prince/ Finolex including fixing with approved adhesive etcetraetra.complete The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

150mm nominal bore/diameter.

110mm nominal bore/diameter

Providing and fixing P.V.C. cowl of Supreme/ prince/ Finolex including fixing with approved adhesive etcetraetra complete The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

150mm nominal bore/diameter.

110mm nominal bore/diameter

Providing and fixing 110 x 90 mm (One hundred ten into ninety millimeter) nominal size/diameter P.V.C. floor trap of Supreme/ prince/ Finolex ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetra complete including carriage of material within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing Orrisa pan W.C No. 20090 star white/snow white shade of Cera / Hindware/jaquar sanitary ware vitreous china water closet squatting pan (Orrisa type W.C. pan) size 53 x 41mm Orissa pattern (earth work, bed concrete, foot rest and trap to be measured and paid for separately) as per approved specification and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing European sheet No 20087(S-10) of size 57x35x39 cm Cera / Hindware / ESSESS/Jaguar vitreous china water closet of star white/snow white shade (European type with integral P or S trap including jointing the trap with soil pipe in cement motar of approved adhesive (sheet cover and jet spray to be measured and paid for separately) as per approved specification and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing vitreous china wash down water closet (W.C) of marix of cera/hindware/ jaquar with intergral P or s trap including jointing the trap with soil pie with adhesive / cement morter 1:1for person with disabality as per specifications and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing P.V.C.10.00 litres capacity low level flushing cistern of cera/Hindware/ESSESS/Jaquar with a pair of C.I or mild steel brackets, complete with fittings such as lead valve , syphon 15mm nominal size bras s, ball valve, with polythene float, C,P brass handle, unions and couplings for connections with inlet, outlet and over flow pipes 40mm dia C.P flush pipe including cutting holes in walls and making good the same and connecting the flush pipe with cistern and closet as per approved specification and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 110mm size PVC 'P ' or ' S ' trap for water closet (squatting pan) including jointing the trap with the pan and soil pipe with adhesive The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing plastic seat (solid type) and cover of Cera / Hindware / ESSESS/Jaguer of approved shade for wash down water closet with C.P. Brass hinges and rubber buffers with cover. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing vitreous china metreix wash basin of Cera/Hindwere /jaquare haveing size 55x40x80 centimetre (fifty five int forty into eighty centimetre)of star white/snow white shade with single hole for piller tap with pedestal including C.I.or M.S breckets, painted white including utting holes and making good yhe same but excluding fittings for persons with disability including carriage of material within all leads,lifts and other incdental. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing vitreous china bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with chopped hemp of Cira / Hindware / jaquare/ ESS-ESS flat back large urnil no 60002 of size 39 x 37.5 x59 cm of star white /snow white shade (waste pipe to be measured and paid for separately. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 600mmx300mm vitreous china division plate of / Cera / Hindware/ jaquare/star white /snow white shade for urinals includings fittings complete as per approved specification drawings and entire satisfaction of Engineer-In-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing vitreous china wash basin delta No 10010 of Cira / Hindware / jaquare heaving size 55x40x/80(fifty five nto forty into eighty centimetre)of star white /snow white shade with single hole for pillar tap with C.I. Or M.S brackets painted white including cutting holes and making good the same but excluding fittings The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing vitreous china under wash basin countr of garnete No 10080 58 x 43x 80 cm sizeof Cira / Hindware / jaquare of star white /snow white shade with single hole for pillar tap with C.I. Or M.S brackets painted white including cutting holes and making good the same but excluding fittings The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing stainless steel kitchen sink size 610 x 460 mm with bowl depth 200 mm of AMC / UNIK/ Diamond of ISI marked with drain board and C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing vitreous china pedestal of Cera / Hindware/jaguar for wash basin complete heaving recessed at the back for the receiption of pipe and fittings. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 32mm diameter rubber plug for wash basin (Heavy duty ). The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 32mm diameterM.I. union for wash basin or sink Jal/Jaguar/ESSESS including necessary fittings. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 32mm diameter P.V.C. waste pipe Supreme/finolex/prince waste pipe for wash basin or sink including brass check nut The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 100mm diametre C.P. Grating of clarion series of classik or contessa plus Jaquar / (Heavy duty makes ISI marked ) for gully / floor or Nahni trap including fitting in all respect The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing flat back 600x450mm beveled edge mirror of superior glass of Atul/Modi Gaurd mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washers etcetraetra complete. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing C.P.(chromium plated) brass towel rail having size 600x20 mm of clarion series of classik or contessa plus Jaquar of approved quantity complete withC.P. brass brackets fixed to wooden plugs with C.P. brass screws etcetraetra complete. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 600x120mm glass shelf (Heavy duty makes ISI marked IS No. 8931 & 8934) with C.P. brass brackets and guard rail complete fixed to wooden plugs with C.P. brass screws etcetraetra complete. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing C.P. Brass Toilet paper holder of clarion series of classik or contessa plus Jaquar (Heavy duty make ISI marked including fitting complete in all respect) The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing chromium plated jet pressure of clarion series of cassik or contessa plus Jaquar complete in all respect. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm nominal bore fancy bib tap chromium plated ISI marked IS No. 8934 of clarion series of classik or contessa plus Jaquar with necessary fittings including entire carriage of material with in all leads and lifts .The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm diameter C.P.(Chromium plated) brass stop cock of clarion series of classik or contessa plus Jaquarwith fitting complete. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm dia C.P. brass pillar tap with capstan head of clarion series of classik or contessa plus Jaquar with fitting complete in all respect .The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm diameter C.P. brass angle valve of clarion series of classik or contessa plus Jaquar with nuts as per approved specifications drawing ,design and as directed by the Engineer-Incharge

Providing and fixing 15mm nominal bore brass full way valve with wheel of clarion series of classik or contessa plus Jaquar with necessary fitting including entire carriage of material with in all leads, lifts and other incidentals.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm nominal bore brass valve (Horizontal plunger type) of Jal/Jaquar/high pressure with copper plate with necessary fitting including entire carriage of material with in all leads , lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm nominal bore PVC connection pipe with brass union 45cm length, with necessary fittings. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing P.V.C. waste pipe of Supreme/finolex/prince for wash basin or sink including brass check nut The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing PVC water Storage tank of (Sintex/ supreme / finolex ) tripple layer 1000 litres net capacity ISI marked with G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto any height above ground level including carriage of material with in all leads , lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying to level or slopes PVC pipe for sewerage line of diametre 150 mm overall 8 mm thick of supreme/Finolex/Prince and jointing with approved adhesive complete .The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (One cement: five sand: ten graded crushed stone aggregate 40mm (Forty millimeter) nominal size for bedding for 150 mm (one hundred fifty millimeter) diameter P.V.C. pipe including necessary form work and curing complete, as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Construction of manhole with R.C.C. top slab in 1:2:4(1 cement: 2 sand: 4 graded crushed stone aggregate 20mm nominal size) foundation concrete 1:4:8(1 cement: 4 sand: 8 graded crushed/broken stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1 Cement: 3 sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(1 cement: 2 sand: 4 graded crushed stone aggregate 20mm nominal size) finished smooth complete including curing and testing inside size 800x800x500mm deep, including C.I. cover with frame (light duty single seal pattern -I) 455x610mm internal dimensions.Total weight of cover and frame to be not less than 38 Kg, Weight of cover 23Kg and weight of frame 15 Kg with 300mm thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (1 cement: 3 sand). The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Construction of manhole with R.C.C. top slab in 1:2:4(1 cement: 2 sand: 4 graded crushed stone aggregate 20mm foundation concrete 1:4:8(1 cement: 4 sand:8 graded crushed/broken stone aggregate 40mm inside plastering 15mm thick with cement mortar 1:3 (1 Cement: 3 sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(1 cement: 2 sand: 4 graded crushed stone aggregate 20mm nominal size) finished smooth complete including curing and testing inside size 800x800mm 1.00 mtr deep, including C.I. cover with frame (light duty single seal pattern -I) 455x610mm internal dimension. Total weight of cover and frame to be not less than 38 Kg. Weight of cover 23Kg and weight of frame 15 Kg with 300mm thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (1cement: 3 sand) .The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Constructing of brick masonry chamber for underground C.I. inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (1 cement : 5 sand C.I. cover with frame (light duty) 355x610mm (Three hundred fifty five into six hundred ten millimeter) internal dimensions. Total weight of cover and frame to be 38 kg (thirty eight kilogram) weight of cover 23kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram). RCC top slab with 1:2:4 ( one cement : two sand: four graded crushed stone aggregate 20mm (twenty millimeter) foundation concrete 1:5:10 (1 cement : 5 sand : 10 graded crushed /broken stone aggregate 40mm (forty millimeter) nominal size inside plastering 15mm (Fifteen millimeter) thick with cement mortar 1:3 (1 cement : 3 sand) finished with a floating coat of neat cement on walls and bed concrete etcetraetera complete inside dimensions 455x610 mm (Four hundred fifty five into six hundred ten millimeter) and 450mm (Four hundred fifty millimeter) deep single pipe line complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixingPE-AL-PE-Composite end seal compression fittings of Kitec as per IS:15450-2004 for cold water supply tees,elbows,reducers,connectors,couplers and clamps with jointing testing and fitting complete including cutting and making good the wall etcetraetera and entire carriage of material with in all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

Equal tees (1620)

Equal tees (2025)

Female Elbow (1620x15 mm thread)

Female Elbow (2025x15 mm thread)

Female branch Tee (2025x2025x20 mm thread)

Female branch Tee (1620x1620x15 mm thread)

Coupler 2025

Coupler 1620

Male thread Connector 2025x15 mm thread

Male thread Connector 1620x15 mm thread

Excavation in drains and channels etcetraetra in earth work in all kind of soil, such as pick work, jumper work, pick jumper work, blasting work, hard and soft blasting, saturator soil including chiseling or any other mixed variety of soil, lift upto any heights, stacking the excavated soil for all heights from the edge of excavation and then returning the stacked soil in 15cm layer when required into plinths sides of foundations etcetra. Consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by the Engineer- Incharge .The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.

SUNIL DUTT