Construction of Additional Accommodation 4 Rooms at Govt. Sr. Sec. School Bhoura in Tehsil Palampur Distt. Kangra HP

Amount

Excavation in foundation, trenches etcetera in earth work involving all classification of soil such as pick work, pick jumper work, blasting work, soft or hard rocks including chiseling/wedging out of rocks where blasting work is prohibited or any other mixed variety of intermediate soil, dewatering and removal of slush if arrisen during course of construction and lifts upto all heights including stacking the excavated soil not more than three meters clear from the edge of the excavation and then returning the stacked soil in 15 cm (fifteen centimeters) thick layers when required into plinths, sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus excavation earth within all leads,lifts by any mode of transportation and other incidental, as per the direction and entire satisfaction of Engineer-In-Charge. Any loss to the private and public property during course of construction shall be absolute responsibility of the contractor. Rate is inclusive of royalty, malkana, toll tax, GST and other taxes imposed by the government.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of royalty, malkana, toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetra, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation, Footings bases of columns and mass concrete. The rate is inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetra, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillars , posts and struts, square, rectangular, polygonal in plain in all floor level including of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetra, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like floor etcetra including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams, cantilevers, girders, lintels, sides, and soffits of beams haunchings, cantilevers bressumers and lintels upto all depths in all floor including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls up to any width including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing in all floor including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:6:12 (One cement isto six sand isto twelve aggregate) graded crushed stone aggregate 40mm (forty milimeter) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth as per approved specification and drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:4:8 (One cement isto six sand isto eight aggregate) graded crushed stone aggregate 40mm (forty milimetre) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth as per approved specification and drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete grade M-25 (M-Twenty five) design mix with minimum compressive strength 25N/mm2 (Twenty five newton per millimetre square) with cement contents not less than 400 Kg (Four hundred kilogram) per cubic metre mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design excluding the cost of form work and reinforcement for reinforcement cement concrete work in foundation and footing and basis of column and the like mass concrete as per approved specification and drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete grade M-25 (M-Twenty five) design mix with minimum compressive strength 25N/mm2 (twenty five newton per millimetre square) with cement contents not less than 400 Kg (Four hundred kilogram) per Cubic metre mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design excluding the cost of form work and reinforcement for reinforcement cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc upto any floor level including carriage of materials with in all leads, lifts and other incidentals and further as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of Royality, Malkana, sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete grade M-25 (M-Twenty five) design mix with minimum compressive strength 25N/mm2 ( twenty five newton per millimetre square )with cement contents not less than 400 Kg (Four hundred kilogram) per Cubic metre mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design excluding the cost of form work and reinforcement for reinforcement cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto any floor level including carriage of materials with in all leads, lifts and other incidentals and further as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of Royality, Malkana, sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying tor steel of TataTISCO, SAIL reinforcement for reinforced cement concrete work including bending, binding and placing in position complete in all respects as per approved drawing, design, and specification in all floor levels including the cost of binding wire and dewatering if arrisen during placement of reinforcement as per PWD specification and approved, drawing design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying Damp Proof Course 40mm (Forty millimetre) thick with cement concrete 1:2:4 (One cement isto two coarse sand isto four graded stone aggregate) mechanically mixed including cost of form work and curing complete, as required at site as per H.P.P.W.D. specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rate is including octroi, royality, Malkana, toll tax, sales tax, GST or other taxes imposed by the Government.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg (One decimal seven killogram) per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil as required at site as per H.P.P.W.D. specification, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rate is including octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government.

Second class brick work using common burnt clay building F.P.S. (non modular) bricks in cement mortar 1:6 (one cement isto six sand) in super structure upto all floor levels as per PWD specification, drawing and design and curing complete including scaffolding and cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Second class half brick work using common burnt clay building F.P.S. (non modular) bricks with hoop iron in cement mortar 1:4 (one cement isto four sand) in super structure as per PWD specification, drawing and design and curing complete including scaffolding. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Random rubble masonry with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement isto six sand isto Twelve graded stone aggregate) 20 mm (Twenty millimetre nominal size) at plinth level in cement mortar 1:6 (one cement isto six sand ) including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Coursed rubble masonry (first sort) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement isto six sand isto Twelve graded stone aggregate) 20 mm (Twenty millimetre nominal size) at plinth level in cement mortar 1:6 (one cement isto six sand ) including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. channels for doors, windows, frames manufactured from M.S. section 40mmx75mmx4mm (Forty millimetre into seventy five millimetre into four millimetre) with M.S. flat 75x4mm (Seventy five into four millimetre) in combination as per drawing and design including hinges, jamb, lock jamb beed and if required thrashold including thrashold of M.S. angles means lugs, with split and tails to each jamb including iron butt hinges 2.5mm (Two decimal five millimetre) thick with a provision of locking arrangement and shock observers as specified and applying a coat of approved steel primer after pre-treatment of the surface complete, as required at site as per H.P.P.W.D. specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rate is including octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government.

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm (Thirty five into thirty five into five millimetre), joints mitred and welded by angle iron 35x35x5 mm (Thirty five into thirty five into five millimetre) or 35x 5 mm (Thirty five into five millimetre flat pieces to the existing T iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer complete, as required at site as per H.P.P.W.D. specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rate is including octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government.

Providing and fixing 35 mm thick (Thirty Five millimetre) Second class Deodar wood panelled glazed or panelled and glazed shutters for doors, windows and clearstory windows including ISI marked pressed butt hinges with necessary screws complete (exluding panelling which will be paid for separately), as required at site as per H.P.P.W.D. specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rate is including octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government.

Providing and fixing 12 mm (Twelve millimetre) thick pre-laminated particle board (decorative lamination on both sides) grade-1, medium density flat pressed, three layer particle board FPT-I or graded wood particle board FPT-I, conforming to IS: 3087, bonded with BWP type synthetic resin adhesive as per IS: 848 and pre- laminated conforming to IS : 12823, Grade-1, Type -II marked complete as required at site as per H.P.P.W.D. specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rate is including octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm (Fifty into forty seven millimetre) with a wall thickness of 5 mm (Five millimetre), made out of extruded 5mm (Five millimetre) rigid PVC foam sheet, mitred at corners and joined with 2 Nos (Two Numbers) of 150 mm (One hundred fifty millimetre) long brackets of 15x15 mm (Fifteen into fifteen millimetre) M.S. square tube, the vertical door frame profiles to be reinforced with 19x19mm (Nineteen into nineteen millimetre) M.S. square tube of 19 (Nineteen) gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm (Sixty five/ Hundred millimetre) size complete, as required at site as per H.P.P.W.D. specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rate is including octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government

Providing and fixing factory made 30 mm (Thirty millimetre) thick Polyvinyl Chloride (PVC) door shutter made of styles and rails of a PVC hollow section of size 60x30 mm (Sixty into thirty millimetre) and wall thickness 2 mm (Two millimetre) (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm (Seventy five into two hundred twenty millimetre) having wall thickness 1.0 mm (One millimetre) and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm (Twenty five into twenty millimetre) and 1 mm (One millimetre) (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a PVC hollow section of size 100x30 mm (One hundred into thirty millimetre) and 2 mm (Two millimetre) (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm (Sixty hundred twenty millimetre), having over all thickness of 20 mm (Two millimetre) and 1 mm (One millimetre) (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm (Six millimetre) galvanised M.S. rod and fastened with nuts and washers, complete as per H.P.P.W.D. specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rate is including octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government.

Providing and fixing M.S. plain grills 10x10mm (Ten into ten millimetre) square bar in combination of 20x4mm (Twenty into four millimetre) M.S. flat as per design required pattern in wooden frames of windows etc. with M.S. round headed bolts and nuts or by screws. The rate is inclusive of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing size coloured / anodized aluminum sliding door bolt ISI marked (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete. The rate is inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

300x16mm (Three hundred into sixteen milimetre)

250x16mm (Two hundred fifty into sixteen milimetre)

Providing and fixing 250x10mm (two hundred fifty into ten millimetre) size coloured anodized aluminum tower bolts ISI marked (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 125mm (One hundred twenty five millimetre) size coloured / anodized aluminum handle anodized transparent or dyed to required shade or colour with necessary screws etcetra complete. The rate is inclusive of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 100mm (One hundred millimetre) ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etcetra complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etcetra complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections joints mitred and welded with 16x3.15mm(Sixteen into three decimal fifteen milimetres) lugs 10cm (Ten centimetres) long with steel plugs and screws or rawl plugs screws or with fixing clips or with bolts and nuts as required and iron fitting, including providing and fixing of glass pans with glazing clips and special metal sash putty of approved make complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Fixed steel windows

Top hung Ventilators

Providing and fixing factory made double steel shutter side hungs (one glazed and one wire gauge) for steel windows side hung (one glazed and other wire gauged) of standard rolled steel sections, jointing mitered welded with manufactured to relevant ISI standard specification with steel plugs and screws or rawl plugs screws or with fixing clips or with bolts and nuts as required and iron fitting, including providing and fixing of glass pans with special putty of glazed side of shutter and wire gauge of IS designation 85G with metal beading on other side complete including priming coat of red lead paint. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 600x600x10mm (Six hundred into six hundred into ten millimetre) double charge / Ultra Charge vetrified tiles of Resitile/ Nitco/ Kazaria/Rak water proof stain and impact resistent hevy duty viterified tiles manufactured of approved shade and colour in flooring on 12mm (Twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 600x600x10mm (Six hundred into six hundred into ten millimetre) double charge / Ultra Charge vetrified tiles of Resitile/ Nitco/ Kazaria/Rak water proof stain and impact resistent hevy duty viterified tiles manufactured of approved shade and colour in skirting jointed with cement slurry mixed with pigment to match the shade of tiles as required complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 600x600 mm (six hundred intosix hundred millimetre) full body matt finish vetrified tiles of restile/ Nitco/ Rak/ Simpolo/ Kajaria/ Johnson as per approved shade in flooring (thickness to be specified by the manufacturer), with water absorption less than 0.08% (zero decimal zero eight percent) and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm (Six millimetre) thickness, including grouting of joints (Payment for grouting of joints to be made separately) as required complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 600x600 mm (six hundred intosix hundred millimetre) full body matt finish vetrified tiles of restile/ Nitco/ Rak/ Simpolo/ Kajaria/ Johnson as per approved shade (thickness to be specified by the manufacturer), with water absorption less than 0.08% (zero decimal zero eight percent) and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade in skirting, riser of steps, over 12mm (Twelve millimetre) thick bed of cement mortar 1:3 (One cement isto three sand), jointing with grey cement slurry @ 3.3 kg/ sqm (at the rate of three decimal three kilogram per square metre) including grouting the joints with white cement and matching pigments etc. as required complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying matt finished vitrified tile of size 300x300x9.8mm (Three hundred into three hundred into nine decimal eight millimetre) having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (One cement isto four coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. as required complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 600x600 mm (six hundred intosix hundred millimetre) vetrified floor tiles of restile/ Nitco/ Rak/ Simpolo/ Kajaria/ Johnson as per approved shade (thickness to be specified by the manufacturer), with water absorption less than 0.08% (zero decimal zero eight percent) and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid over 20mm (Twenty millimetre) thick bed of cement mortar 1:4 (One cement isto four sand), jointing with grey cement slurry @ 3.3 kg/ sqm (at the rate of three decimal three kilogram per square metre) including grouting the joints with white cement and matching pigments etc. as required complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 300x300x25mm (Three hundred into three hundred into twenty five millimetre) labrador design (Rainbow series) Tile of NTC/ Atlantic/ Unistone flooring on 20mm (twenty millimetre) average thick base of cement Mortar 1:3 (One cement isto three sand) laid on Ramp and jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing, polishing, cutting and moulding complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying Kota stone slab 20 mm (Twenty millimetre) thick Single slab flooring of approved shade over 20mm (Twenty millimetre) average thick base of cement mortar 1:4 (One cement isto four sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing as per approved specification, drawing and design and entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Kota stone slab 20 mm (Twenty millimetre) thick in Single slab with round noising for treads and riser of stairs approved shade 12mm (Twelve millimetre) average thick base of cement mortar 1:4 (One cement isto four sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing as per approved specification, drawing and design and entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing pre-painted sheet roofing of kotar metal single skin trapezoidal 10 (ten) refitted sheeting 0.60mm (zero decimal six millimetre) thickness having 1060mm (one thousand sixty millimetre) cover width cover all width 1126mm (One thousand one hundred twenty six), 28mm (Twenty eight millimetre) crest depth at 353mm (three hundred fifty three millimetre) 2.50mm (two decimal five zero millimetre) the main crest with at top 25mm (Twenty five millimetre) and at lower 81mm (Eigthy one millimetre) base metal of coil rolled steel coil with zinc waiting top coat with regular modified polysters coating of approved shade and balancing reverse coat 5.5mm (five decimal five millimetre) dia and 55mm (fifty five millimetre) length with EPDM seal complete in all respect as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing pre-painted sheet ridge or hips 60cm (sixty centimetre) over all of kotar metal skin trapezoidal profiled sheeting 0.60mm (zero decimal six zero millimetre) cover with over all width 1126mm one thousand one hundred twenty six millimetre), 28mm (twenty eight millimetre) crest depth at 353mm (three hundred fifty three millimetre) 2mm (two millimetre) centre to centre crest distance. There will be two ribs at the centre for stiffening heaving crest depth of 2.5mm (two decimal five millimetre) the main crest with at top zinc waiting top coat with regular modified polyster coating of approved shade and balancing reverse coat 5.5mm (five decimal five millimetre) dia and 550mm (five hundred fifty millimetre) length with DPDM seal complete in all respect as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing pre-painted sheet valleys 90cm (Ninety centimetre) over all of kotar metal single skin trapezoidal profiled sheet 0.60mm (zero decimal six zero millimetre) thickness having 1060mm (One thousand sixty millimetre) cover width aver all width 1126mm (One thousand one hundred twenty six millimetre) of TATA Durashine/ Sail in roofing with hot dipped metalic zinc coated sheet with top coat of regulatr modified polyster organic coating of primer coating including fixing with J or L hooks, bolts and nuts 6mm (Six millimetre) dia with prepainted limpet and bitumen washers complete in all respect as per specifications approved drawing and designincluding cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. B.P. sheet 2 mm (two millimetre) thick of TATA/SAIL for eaves board/Facia/Soffit/Ceiling including cutting, fixing and jointing with gass/electric welding with steel roof member and applying a coat of red lead primer complete as per PWD specification, approved drawing and design (frame work is to be measured and paid for separately) including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15cm (Fifteen centimetre) wide, 45cm (Forty five centimetre) overall semi circular plain G.S. sheet gutter of 0.63mm (zero decimal six zero millimetre) thick sheet with zinc coating not less than 275 gm/ sqm (Two seventy five gram per square metre) fixed with iron brackets 40x3mm (Forty into three millimetre) siz, bolts, nuts and washers etcetra including making necessary connections with rain water pipe complete including cost and carriage of material with in all leads, lifts and other incidentals, as per specifications, approved drawing and design, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 150 mm (One hundred fifty millimetre) Single socketed pipes on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten millimetre) gap for thermal expansion, complete in all respect as per specifications approved drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten millimetre) gap for thermal expansion complete in all respect as per specifications approved drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

150mm (one hundred fifty millimetre) dia PVC plain bend

150mm (one hundred fifty millimetre) dia PVC shoe

Providing and fixing 100mm (One hundred millimetre) diametre M.S. holder bat clamps of approved design to P.V.C pipes embedded in and including cement concrete block 10cmx10cmx10cm (Ten centimeter into Ten centimeter into Ten centimeter) of 1:2:4 (One cement is to Two Sand is to Four graded crushed stone aggregate 20mm (Twenty milimetre) nominal size and cost of cutting holes and making good the wall etcetera. The rate is inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Structural steel work riveted, bolted or welded in built up sections of Tata/Sail in beams, joists, channels, angles, tees flats with connecting plates or angles, cleats as in trusses and trussed purlins, main and cross beams, hips, jack rafters, purlins connect to common rafter and like work including cutting hoisting fixing in position & applying a priming coat of red lead paint complete including entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 595x595x6mm (Five hundred ninety five into fiive hundred ninety five into six millimetre) designer bison board ceiling excluding the cost of pre-painted GI channel framing @ 600 mm c/c (Six hundred millimetre centre to centre) complete as per PWD specification,approved drawing, design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 595x595x6mm (Five hundred ninety five into fiive hundred ninety five into six millimetre) designer board of everest (E-Board) ceiling with pre-painted GI channel framing @ 600 mm c/c (Six hundred millimetre centre to centre) complete as per PWD specification,approved drawing, design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Painting two coats (excluding priming coat) on new steel surfaces with Dulux Multi Surface paint of required shade applied at the rate of 0.90 ltr/10 sqm (zero decimal nine zero litre per ten square metre) over an under coat of primer applied at the rate of 0.80 ltr/ 10 sqm (zero decimal seven five litre per ten square metre) including cleaning the surfaces of all dirt, dust and other foreign matters and sand papering and knotting as per PWD specification including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

6mm (six millimetre) cement plaster 1:3 (one cement isto three sand) in ceiling and curing complete as per PWD specification including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

20mm (Twenty millimetre) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (eighty millimetre) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete as per PWD specification including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

20mm (Twenty millimetre) thick cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (eighty millimetre) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete as per PWD specification including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

20mm (Twenty milimetre) thick cement plaster on the fair side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (eighty millimetre) in girth, with cement mortar 1:5 (one cement isto five sand) including curing as per PWD specification and cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface complete as per PWD specification including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Finishing wall with Apex weather proof exterior emulsion of Asian paint/ Nerolak Suraksha paint/ Berger paint/Dulux paint of approved brand and manufacture and of required shade on undecorated wall surfaces (Two or more coats) to give an even shade after thoroughly brushing the surface to remove all dirt, dust and remains of loose powdered material including cost and carriage of material with in all leads, lifts and other incidentals as per specificatins, approved drawing as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Applying Birla white wall care putty over plaster surface after throughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters and sand papered smooth to give final matt finish to the surface complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Wall painting interior emulsion paint of Asian paint / Nerolac Suraksha Paint/ Berger paint / Dulux paint of approved shade for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty required for matting the surface and cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing Railing for Ramp having Baluster of 25 mm ( Twenty five millimetre) dia hollow stainless steel hand rail pipe welded with a clear height of 85 cm (Eighty five centimetre) @ 60 cm (at the rate of sixty centimetre) centre to centre emended in cement concrete step and jointing with electric/ gas welding at top alongwith hand rail of hollow SST pipe of 50mm (Fifty millimetre) dia slip resistance vertical baluster welding / jointed with each other with 2 Nos (Two Numbers) SST pipe of 20x20 mm (Twenty into twenty millimetre) complete and one no round pipe for handicaped persons complete.as per detail drawing, design and specification including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax toll tax, GST and any other taxes imposed by the government.

Providing and fixing stainless steel 85 cm ( Eighty five centimeters) high know down stair railing of kitch 38 mm (thirty eight millimetre) dia hand rail fixed on 10x50 mm ( ten into fifty millimetre) side mounted flat blauster system with glass no DS 54-2- G-10 placed at 1200 mm ( twelve hundred millimetre) center to center along with 3 Nos (three numbers) 10mm ( ten millimetre) mid rail connected at side of blauster with fixes on the blauster would be fixed on floor with casted base plate on minimum 6 mm (six millimetre) thickness base plate shall be conncected with suitable SS grade over cape alinging complete as per detail and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing plinth protection with 60 mm (Sixty millimetre) thick interlocking tiles/ cement concrete paver block with 23 cm ( twenty three centimetre) dia half round RCC pipe for drainage purpose laid over 10cm (ten centimetre) concrete 1:5:10 (one isto five isto ten) in bedding/ haunching complete including cost and carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 2400x1200 mm (Two thousand four hundred into one thousand two hundred millimetre) green chalk board/Black board shall be made of steel of thikness 0.3 to 0.4 mm (zero decimal three to zero decimal four millimetre) It shall have vitreous Enmal coating of 0.095 mm (zero decimal zero nine five millimetre) minimum thickness on top and 0.3 mm (zero decimal three) on the back. top shall be free from waviness and shall show excellient ability. The core material shall be 9mm (Nine millimetre) thik MDF board heaving bluk density of 750kg/cum (Seven hundred fifty kilogram per cubic metre) and grade-1 as per IS : 212406-203 edition 2.2 the backing material sheet shall be min. 0.25mm (zero decimal two five millimetre) thick electro galvanised steel sheet conforming to is: 277-2003. The board shall be fixed on the wall with specially designed J clamps and square clamps with the help of Nylon sleves and screws as per site requirement and as per specification including cost and carriage of material with in all leads, lifts and other incidentals. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing orisa Pan No 20090 of size 53x41 cm ( fifty three into forty one centimeter) vitreous china water closet squatting pan (Indian Type W.C. Pan) of Cera/hindware/ Jaguar of star white/ snow white shade with low level PVC cistern (earth work, bed concrete, foot rest PVC cistern and trap to be measured and paid for separately) including entire carriage of material within all leads, lifts and other incidentals as per direction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing vitreous China wash down water closet (European type W.C. pan) of Constellation No. S No. 20087(S-10) size 57x35x39cm (Fifty seven into thirty five into thirty nine centimetre) with PVC Cistern (Sleek plus) and fixed with jet pressure of Hindware /Cera/ Jaquar of star white / snow white shade with intergal P or S trap including jointing the trap with soil pipe in cement mortar 1:1 (One cement isto one sand) (seat cover and jet spray to be measured and paid for separately) and further as per Architectural drawing ,design and specifications including entire carriage of material within all leads, lifts and other incidentals as per direction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing white vitreous china wash basin Garnet No 10080 and size 58x43 cm (fifty eight into forty three centimetre) equavalent 32mm (Thirty two millimetre) dia waste of standard pattern with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same including all fitting complete in all respect including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 32mm (Thirty two millimetre) diametre PVC Waste pipe for wash basin or sink including brass check net with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 100mm (One hundred milimetre) nominal size diametre CP grating of ESS-KSS for nalhni trap of approved shade complete, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing G.I. inlet connection pipe for each flush pipe with W.C. pan as per Architectural drawing, design and specifications including entire carriage of material within all leads, lifts and other incidentals as per direction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 600x450mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass 6mm (six millimetre) thick of Modiguard/ Atul/ Golden Fish mounted on 6mm (six millimetre) thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. screws and washers including entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 600x120x5mm (Six hundred into One hundred twenty into five millimetre) glass shelf with C.P. Brass bracket and guard rail fixed with 40mm (Forty millimetre) long screws, rawl plugs etcetra complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing chromium plated brass soap dish of continental series of Jaguar/ Classic series of Hindware/ Floral series of Cera/ Hindson series of Jal ESS with C.P. brass brackets fixed with cleats C.P. brass screws including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm (Fifteen milimetre) diameters C.P. brass long nose bib cock F-330011 Hindware/ Floral series of Cera/ Hindson series of Jal single control of approved quality confirming to IS standard as per specifications including carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. brass stop cock (concealed) of standard design F-330043 of Continental/Classic/ Floral series of Jaguare/Hindware/Cera 15mm (fifteen millimetre) dia complete as per specifications including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. Pillar cock of standard design F-330002 of Continental/Classic/ Floral series of Jaguare/Hindware/Cera 15mm (fifteen millimetre) dia complete as per specifications including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing uplasticised PVC connection pipe with brass union complete in all respect as per specifications approved drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing Polythelene Aluminium Polyethelene PE-AL-PE Composite tank IS: 12701 marked, with cover and suitable locking arrangement with necessary fitting including over flow pipes, scour pipe, ball valve and with cover locking arrangement of good quality including providing pads of sizes as required good quality all complete as per specifications including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 1216 ( 16mm OD Pipe) Concealed work, Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS-15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C (Eighty degree celsius), including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 (One) metre spacing. This includes the costs of cutting chases and including testing of joints complete including cutting chases and aking good the wall etcetra within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 20mm (Twenty millimetre) diametre G.I. pipes complete with G.I. Fittings including trenching and refilling etcetra within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:5:10 (One Cement isto Five Sand isto ten) graded stone aggregate 40mm (Forty millimetre) nominal size for bedding of pipes, necessary form work and curing complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing high pressure P.V.C spigot and socket soil, waste and ventilating pipe of Supreme/Finolex working pressure not less than 6.0 kg/cm2 (Six kilogram per square centimetre) I.S.I Marked including fixing with approved adhesive etcetra complete including carriage of material within all leads, lifts and other incidentals. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

75 mm ( Seventy five millimetre)

110 mm ( One hundred ten millimetre)

150 mm ( One hundred fifty millimetre)

Providing and fixing PVC single Equal Branch with oval access door ISI Marked of Supreme/ Finolex with insertion rubber washer 3 mm (Three millimetre) thick bolt and nuts complete including fixing with approved adhesive etcetra Complete including carraige of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

75 mm ( Seventy five millimetre) diametre

110 mm ( One hundred ten millimetre) diametre

Providing and fixing vitreous China urinal flat Back (large) No. 60002 of size 39x37.5x39cm (Thirty nine into thirty seven decimal five into thirty nine centimetre) with auto cistern of make Hindware/Cera /Jaguar of snow white colour including connection with urinal and waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately complete complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing Division Plate for urinals 600x300 mm (Six hundred into three hundred millimetre) of viterous china of Jaguar/ Hindware/ Cera including carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and fixing 110x75 mm (one hundred ten into seventy five millimetre) PVC Floor Trap ISI marked self cleaning design including fixing with approved adhesive cost of cutting and making good the wall and floor complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Constructing masonry Chamber 90x90x100cm (Ninety into ninety into one hundred centimetre) inside, in brick work in cement mortar 1:4 (One cement isto four coarse sand) for sluice valve, with C.I. surface box 100mm (One hundred millimetre) top diameter, 160 mm (One hundred sixty millimetre) bottom diameter and 180 mm (One hundred eighty millimetre) deep ( inside) with chained lid and RCC top slab 1:2:4 (One isto two isto four) mix (One cement isto two coarse sand isto four) 20mm (Twenty millimetre) nominal size graded stone aggregate including necessary excavation, foundation concrete 1:5:10 (One cement isto five sand isto Ten) 40 mm (Forty millimetre) nominal size graded stone aggregate and inside plastering with cement mortar 1:3 (One cement isto three coarse sand) 12 mm (Twelve millimetre) thick, finished with a floating coat of neat cement complete as per standard design complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

KARNAIL SINGH