Improvement of Railway Stadium Kota and Provision of Air Conditioner at Crew Lobby and Classroom of Kota & Gangapur City Station.

A-Tender Schedule

Laying, testing and commissioning of LT XLPE insulated stranded armour conductor cables of various size. The cables to be laid in existing trench/ air/ pipe and connection with crimped lugs & cleating of the cable. Note - Cable will be supplied by Railway.

Digging of trench in pucca trench in yard/ platform 50 cm. deep and 35 cm. wide 02 including re-plaster on surface by cement concrete after laying of cable. Wherever the digging of trench to full size is not possible, measurement will be proportionate to the actual volume of cross section and length of the trench.

Digging of trench in all type of soils/ road cutting 100 cm. deep and 50 cm. wide. B 03 class bricks on both sides and top of the cable are to be provided. Brick length to be kept across the length of the cable including refilling the trench after laying of cable. Payment for trench will be made on flat rate basis, if it is dug more or less by 1 meter, payment will be made proportionately.

Supply of material, providing and laying of RCC hume pipe 6" dia (150mm) as per IS: 456-1978 or latest in existing trench under Railway track including jointing and all required accessories etc.

Supply, laying , fixing of heavy duty ISI marked B class GI pipe of 3.65 mm wall thickness & 50 mm diameter to be laid along the wall or floor with proper galvanized clamp through the wall or underneath the floor in cement concrete.

Supply of material & providing GI. pipe earthing arrangement by digging the pit as per 06 DRM/KTT's Drg. No. 01913EL/R1 or latest complete in all type of soils including rocky area. Earth value will be taken by the contractor in the presence of Railway representative and written on the earth pit by the contractor.

Supply of material and wiring , testing and commissioning of light/fan point in PVC 07 rigid conduit pipe size 19/20 mm medium class with 1.5 sqmm multistrand PVC insulated copper conductor cable confirming to IS: 694-1990 or latest amd 2.5 sqmm PVC insulated copper wire coloured for earthing alongwith connections etc.

Supply of material and wiring , testing and commissioning of sub main phase and 08 neutral in PVC rigid conduit pipe size 25 mm dia. Medium class mark with 4 sq.mm. PVC insulated single core multistrand copper cable with 2.5 sq.mm. PVC insulated copper wire green coloured for earthing and connection etc. Separate PVC pipe to be provided for this item.

Supply of material & fixing of Surface type PVC board of 6-Module with connection used for PVC casing caping wiring.

Supply of material & fixing of S.P. switch 6 Amp. one way (1-Module) used for concealed modular wiring.

Supply of material & fixing of 6 Amp. 5-pin socket (2-Module) used for concealed modular wiring.

Supply & fixing of blank plates (1-Module) used for concealed modular wiring.

Supply of material & fixing of S.P. switch 16 Amp. one way (1-Module) used for concealed modular wiring.

Supply of material & fixing of 6/16 Amp. 6-pin combined shuttered socket (2-Module) used for concealed modular wiring.

Supply of material & fixing of fan regulator 5-step (2-Module) used for concealed modular wiring.

Supply of materials and fixing of main distribution box 10 way suitable for housing MCB and ELCB with copper busbar and neutral link. Distribution box should be fixed on wooden taper 16 plug or steel fasteners etc. with providing and fixing of 01 no. MCB DP 32 Amp. breaking capacity 6 KA and 06 Nos. MCB SP 6-32 Amp. breaking capacity 6 KA with 01 No. ELCB 40 Amp. DP, sensitivity 100 m.Amp. and connections etc. The distribution board is to be fixed on wall with the help of rag bolt /fastener or on board and connecting the same with suitable size of wire duly crimped lugs.

Supply & fixing of T-5 20 watt LED batten 4' long (Approx.) with cool white light complete with extruded aluminum housing with decorative end cap, aluminum heat sink, heat resistant square polycarbonate defuser, input voltage 142 to 270 volts AC, 50 Hz, constant current LED driver with short circuit protection, over voltage protection, under voltage protection, driver 17 surge protection of minimum 1.5 KV ±3% with power factor >0.95. full load efficiency >90%, CRI >75, CCT 5700K to 6500K, THD <20% at full load, view angle of LED should be 120 degrees, LED output efficiency >100 lumens per watt, LED life >50000 hours, fitting should be IP-20, LED should be of OSRAM, PHILIPS, NICHIA, CREE, SEOUL, LUMILEDS, LEDNIUM, AVAGO, SAMSUNG make. (Note - LED data sheet used and driver and LM-80 report should be submitted along with the quotation and along with the delivery challan/bill.)

Supply and fixing of BEE 5 star rated energy efficient BLDC ceiling fan, sweep size: 1200 mm with wiring connection etc as per detailed technical specification as below- Supply and fixing of BEE 5 star rated energy efficient BLDC ceiling fan, sweep size : 1200 mm with Modular Electronic Regulator, length of down rod (without shackle) - 300mm, Motor Brushless DC (BLDC), 18 Super-efficient power consumption(watt) <30 watt, Harmonic Distortion -10% Max., Color- Standard White, Blade thickness (Min.)- 1.1mm, Blade material - Aluminum, Double ball bearing-Yes, Shank Thickness - (Min.) 2mm, Canopy - 02 Nos., Confirming to IS: 374(Latest), Air Delivery 220M³/Min., Speed Control - Modular Electronic Regulator, Availability of test report for NABL/ILAC accredited or Central Govt. Lab to prove product specification - Yes & Test report number & date name and address of Laboratory - Yes.

Supply and installation of LED FLOOD Light Fitting 100 watt complete suitable for 230 V AC 50 HZ. as per attached detailed specification.

Supply, Installation, Testing & Commissioning of High Power LED outdoor Street light of 30 watt LED with power consumption of 30 watts, input voltage 140 to 270 Volt AC, constant current LED driver with power factor >0.9* Surge protection of 4 KV, Inbuilt PFC function, THD <20%, High Power LED of ceremic package with silicon lens suitable for outdoor application with greater 20 than 100 lumens/watt, maximum power per LED should be 2 watts, LED should of OSRAM, EDISON, PHILIPS, NICHIA, CREE, SEOUL, LUMILEDS, LEDNIUM, AVAGO, SAMSUNG make. Secondary lens/optics should be of 12/13 high quality PMMA material. Driver should be of reputed make, view angle of lens should be 120 degree, CRI >165, colour temperature of 5700K, open and short circuit protection, over voltage protection, complete with high quality die cast alluminium, heat sink and toughned glass with IP 65 compliant. (Note: LED data sheet used and driver and LM80 report should be submitted. Warranty certificate of minimum 05 years is compulsory to be submitted.)

Supply & fixing of 'B' class GI pipe fitting made for 40mm dia for fixing of CFL fittings with all required accessories i.e. MS clamps, nut bolt washers etc.

Supply, Fixing, testing & commissioning of exhaust fan sweep size 300 mm suitable for 230volt AC, 50HZ confirming to IS : 2312 latest complete with accessories.

Supply and fixing of wall mounted bracket fan sweep 400 mm suitable for 230 volts , 50 hz moving type confirming to IS : 555 latest complete with accessories with regulator and control switch on & off with accessories.

Supply and installation of Flykill-LITE Insect killer machine approximate:26 Inch L X 4.5 Inch W X 12.5 Inch H. Two tubes 18W X 2 ,Aluminium Body

Supply and installation of LED HIGHBAY FLOOD Light Fitting 100 watt complete suitable for 230 V AC 50 HZ as per detailed technical specifications attached.

Supply & fixing of Wall mounted Air circulator fan sweep size 600 MM suitable for 230 Volt AC 50HZ, 1440RPM, Moving type without Regulator confirming to IS No:2997

Supply of material & Erection of Maintenance Free Earth Electrodes station as per 27 RDSO Specification No. RDSO/Spn./197/2008 or latest as per attached detailed specification. Earth value will be taken by the contractor in the presence of Railway representative and written on the earth pit by the contractor.

Dismantling of existing Tower type Highmast and handing over/ deposited (including transportation) the same to railway store of concerned supervisor.

Required Fabrication work as per site requirement of Dismantled existing Tower type Highmast complete in all aspect (including transportation) .

Erection, testing & commissioning (including transportation) of Tower type Highmast 30 including civil work with all lumaniries and complete in all aspect as per explanatory notes and Drawing . All material regarding civil work & other work as per site rquirement will be provided by contractor. Note : highmast & lumaniries will be provided by railway.

Supply of Stranded compacted circular aluminium conductor A2XFY conductor screened with extruded , semi conducting compound XLPE insulated screened with extruded semi 31 conducting compound in combination with copper tape (0.3 kA to 1 sec) core laid up inner sheath (ST- 2) PVC galvanized steel strip armoured and overall PVC sheathed black cable HT cable size 3 core x 70 sqmm suitable for 11 kV(E) 6.6 kV (UE) confirming to IS 7098(Part-II) 1985 /with latest amendments.

Laying, testing and commissioning of Stranded compacted circular aluminium conductor A2XFY conductor screened with extruded , semi conducting compound XLPE insulated 32 screened with extruded semi conducting compound in combination with copper tape (0.3 kA to 1 sec) core laid up inner sheath (ST-2) PVC galvanized steel strip armoured and overall PVC sheathed black cable HT cable suitable for 11 kV(E) 6.6 kV (UE) confirming to IS 7098(Part-II) 1985 /with latest amendments.

Supply and fixing of 11 kV cable end box outdoor type heat shrinkable type for 11kV XLPE 3 core 50-95 sqmm size and connection with crimped lugs on cable end box.

Supply, erection, testing & commissioning of GO switch 11KV 400Amp 3pole with 9 Nos insulators operating handle along with locking arrangement system hot deep galvanised vertical type .

Supply, erection, testing & commissioning of DO switch fuse 11KV 400Amp pole operated outdoor vertical mounting expulsion type having hot deep galvined base post type insulator and fiber glass fuse carrier.

Supply,erection,testing & commissioning of 11KV gapless metal oxide lighting arrester complete with hardware, fixtures, hot dipped galvanised pin, nut, bolts, washers etc to relevant ISS.

Supply of material and Providing of copper plate Earthing arrangement by digging the Pit. Copper Plate size 600 X 600 X 3 mm as per drg.No.DRM/KOTA/01927/ELR.

Supply & Erection of material for fabricated steel work other than mast with SPS.

Supply & fixing of 9 mtrs long steel joist pole size 175 mm X 85 mm approx weight 19.1 Kg/m .

Supply and fixing of metal clad plug and socket box with 1 pole mcb 20/25 AMP, 250 volt.

Supply, Installation, Testing & Commissioning of 2-Ton Spilt AC as per explanatory notes.

3" Hole in stone/Bricks wall with PVC pipe fixing.

Supply and fixing of PPR drain pipe (1" in main line & ½" in branch line) concealed in wall complete with all accessories like T, Elbow, Socket etc.

Supply of copper tube pipe line 5/8"+ 3/8" copper tube with insulation sleeve with 4 core copper cable 1.5 sq.mm for Split AC.

Installation of copper tube pipe line 5/8"+ 3/8" copper tube with insulation sleeve with 4 core copper cable 1.5 sq.mm for Split AC.

Supply of 5.0 KVA Automatic line voltage stabilizer.

Supply and fixing of 'L' type wall mounted stand for outdoor split AC units.

Supply of material & wiring of sub main phase and neutral in PVC casing caping 25 mm./concealed wiring (with necessary accessories) with 6 mm² single core multistrand copper cable 48 and 2.5 sq.mm PVC insulated copper stranded green colour wire for earthing along with wiring and connections. Note- (i) Separate rigid conduit pipe /PVC casing caping to be provided for this item. (ii) All material needed for this item are to be supplied by the contractor. Note : As per site requirement wiring may be PVC casing caping or concealed with required necessary accessories with approval of competent authority.

Supply & fixing of MCB distribution board double door Wall mounted having MCCB 100 Amp TPN on incoming & 12 Nos MCB SP 06-32 Amp braking capacity 10 KA, on outgoing connected through busbar & equally distributed on 3- phase complete with connection.

Supply of ISI mark AC Three Phase Energy Meter.

Fixing of ISI mark AC Three Phase Energy Meter.

Supply of PVC Box for fixing of three phase electric energy meter with sealing arrangement. The PVC box is to be fixed on wall with the help of rag bolt /fastener/ray roll plug or on board.

Fixing of PVC Box for fixing of three phase electric energy meter with sealing arrangement. The PVC box is to be fixed on wall with the help of rag bolt /fastener/ray roll plug or on board.

Supply, Installation, fabrication, testing & commissioning of LT Distribution panel Enclosure 16 Gauge fabricated with MS angle Size 1575X1200X400 mm (HXWXD) approx. with door and locking arrangement duly painted red oxide and power coated enamel paint consisting of following items - INCOMING CIRCUIT- 01 No. MCCB 4 pole 160 Amp. 25 KA TM Release, Type: DN1- 54 250C, 415V AC, 50 HZ. Ampere meter with selector switch -01 no., voltmeter with selector switch -01 no., indication lamp RYB 03 nos., Change over Onload Manual 160 Amp. 04 Pole 01 no. with indicator 02 no., CT 150/5A 15VA- 03 nos., Copper busbar Main 200 Amp. rating- 01 set & Earth 200 Amp. - 01 Set, MCB 6A SP C 10KA - 04 nos. OUTGOING CIRCUIT- TM Release 04 no. MCCB 4 pole 63 Amp. 25 KA. All MCCB in incoming and outgoing circuit will provided with Extended Rotary Handle and Spreader Terminals - 4 Pole (Set of 8) etc. as per attached detailed specification.