Interior and Landscaping of Admin Building at Amreli Airport

BILL OF QUANTITIES

(A) Percentage Rate Tender (Up to INR 50 Cr.)

Sr. Quantities Description of Item Tendered Tendered Unit Total amount

Sr. Quantities Description of Item Tendered Tendered Unit Total amount

No. Estimated Rate (Fig) Rate (Words) according to

but may estimated

be more quantities

1 11.00 Three seater sofa-B (2000x750x575) 73,917.07 Seventy No.

The The sofa will be total prepared in Thousand

metal structure. So, 50mm x 50mm Nine

sq. metal furniture pipe section Hundred

created necessity support for 2 Seventeen

seaters sofa. Seat support also been Rupees and

in same metal section. In the metal Seven Paisa

section, the finished seatings must be Only

0.78mm length x 0.53mm width.

Seater also created. then Z-Section

spring use and on top 4''.0' rubber

cushion and top 25mm thick and

density U-Foam finished with lether

recsin as per selected sample. At back

support also 0.53mm width x

…………mm for 2 seater back, fitted

with 2''.0' rubber cushion with 25mm

U-Foam with 32 density appropriate

3'' engle support, also done finishing

alongwith lether finished. To adding

the decorative part 12mm dia. S.S.

crom pipe finish with legs and handle

support also as shown in drawing to

create decoration and strenghning

support.all materials and labour etc.

completing as per detailed drawing

and instruction by engineer-in charge

and consultant.

2 2.00 Single Seater Sofa - B (800x750x575) 29,566.83 Twenty Nine No.

Providing and constructng Single Thousand

seater sofa in size of (0.80x0.75x0.75) Five Hundred

& made from 19mm.thick ply as a Sixty Six

base and support of the seat area as Rupees and

per drawing and back side of the sofa Eighty Three

is also made from 19mm. Thick ply Paisa Only

wood make a box with screw and nail

used, than 4" U-foam 40 density use

in base and back of sofa with 2" thick

super sofa U-foam use adhesive and

cover with selected foam leather, in

handle used 1.5" thick U- foam and

and back side of the sofa also cover

with 0.075 thick U-foam & whole sofa

box rest on 25mm.x25mmx3mm. S.S.

angle and side and back support by

3/4" 19.5mm guage S.S. pipe fitting as

per drawing & instruction of site

Engineer-In- Charge and Consultant.

whole sofa box is rest on S.S. 0.75"dia

support as per drawing & instruction

of site Engineer-In-Charge and

3 4.00 Corner Tipoi - A (0.60x0.80x0.525) 12,735.00 Twelve No.

Providing and constructing Corner Thousand

tipoi top and four legs made from Seven

18mm. Thick ply box detail shown in Hundred

drawing, the ply box should be cover Thirty Five

all over with 4mm. thick SP. Veneer Rupees Only

selected by Engineer-In-Charge and

Consultant. All veneer surfaces should

be melamine polish as per direction.

Necessary hardware and PVC buffer

fixed as per detail drawing and

instruction on Engineer-In-Charge and

4 2.00 Corner Tipoi - C (0.60x0.60x0.525) 17,070.00 Seventeen No.

Providing and constructing Corner Thousand

tipoi made from 18mm. Thick Seventy

plywood box base and side (75mm. Rupees Only

thick) covered with 4mm. thick Sp.

Selected veneer and fine finished with

melamine polish. Two nos. of 40mm.

thick ply wood support covered with

1mm. thick S.S. sheet with selected

finished, top of tipoi 12mm. thick

plain glass supported by necessary

S.S. support should be provided as per

design. PVC buffer fixed as per

drawing and instruction on Engineer-

In-Charge and Consultant.

5 5.00 Corner Tipoi - D (0.60x0.60x0.525) 8,945.85 Eight No.

Providing and constructing Corner Thousand

tipoi made from 18mm. Thick Nine

plywood box base(50mm & 45mm. Hundred

Thick) and two nos. “L” shape support Forty Five

of 45mm. thick covered with 4mm. Rupees and

thick Sp. Veneer fine finished with Eighty Five

melamine polish, top of tipoi 12mm. Paisa Only

thick clear glass fixed on top of box as

shown in drawing and PVC buffer

fixed as per drawing and instruction

on Engineer-In-Charge and

6 1.00 Table (1.20x0.60x0.75) 24,267.30 Twenty Four No.

Providing and fixing table top and side Thousand

support 50mm. thick made from Two Hundred

18mm. thick plywood box covered Sixty Seven

with 1mm. thick selected laminate all Rupees and

around, apron should be provide Thirty Paisa

18mm.+6mm. thick plywood with Only

1mm. thick selected laminate on both

side, 12mm. thick clear glass partition

fixed on table top as per drawing

should be provided. Drawer unit box

PVC/wooden bidding patti on S.S. legs

with lock and telescopic channel

should be made from 18mm. plywood

with 1mm outside and 0.8mm inside

laminate as well as 18mm. post

forming outside of shutter with auto

hinges of HAFELE or equivalent and

drawer should be made from 18mm

post forming laminated in the

approved shade.5mm. thick S.S. strip

should be provided as per detail

drawing. Including all materials and

labour etc. complete as per detailed

drawing and instructions of engineer-

in-charge and consultant.

7 10.00 Table(1.50x0.60x0.75) 25,459.90 Twenty Five No.

Providing and fixing table top and side Thousand

support 50mm. thick made from Four Hundred

18mm. thick plywood box covered Fifty Nine

with 1mm. thick selected laminate all Rupees and

around, apron should be provide Ninety Paisa

18mm.+6mm. thick plywood with Only

1mm. thick selected laminate on both

side, 12mm. thick clear glass partition

fixed on table top as per drawing

should be provided. Drawer unit box

PVC/wooden bidding patti on S.S. legs

with lock and telescopic channel

should be made from 18mm. plywood

with 1mm outside and 0.8mm inside

laminate as well as 18mm. post

forming outside of shutter with auto

hinges of HAFELE or equivalent and

drawer should be made from 18mm

post forming laminated in the

approved shade.5mm. thick S.S. strip

should be provided as per detail

drawing. Including all materials and

labour etc. complete as per detailed

drawing and instructions of engineer-

in-charge and consultant.

8 8.00 Cluster (1.50x1.35x0.75) 24,905.55 Twenty Four No.

Providing and fixing Cluster Thousand

(Workstation) as per drawing, framing Nine

the skeleton with18mm + 18mm thick Hundred Five

vertical and horizontal plywood patti Rupees and

with both side 6mm ply cover for Fifty Five

grooving design and finishing with the Paisa Only

selected laminate. Before installing,

make hole/face plate for conduit

pipes of electrical/networking cables

with open able stud from horizontal

partition. Vertical side support of

18mm thick plywood cover with 1mm

laminate both side finished with

necessary cut out as per design

including PVC/ teakwood bidding on

exposed edges with melamine polish.

Fitted 18mm.+18mm. thick plywood

1mm. thick laminated top, fixed with

metal clamps, including suspended

metal keyboard-mouse tray fixed with

telescopic channel, cable manager

and separate drawer box with lock,

telescopic channel and box and

shutter made from 18mm plywood

with 1mm outside and 0.8mm inside

laminate with auto hinges of HAFELE

or equivalent for left or right side.

Providing and fixing of Soft board

(12mm thick) finished with tapestry of

good quality (min. of Rs. 100/mtr.)

and 12mm. thick clear glass in front of

seating. Including all materials and

labour etc. complete as per detailed

drawing and instructions of engineer-

in-charge and consultant.

9 1.00 Conference Table (12.00 x 0.75 x 269,423.15 Two Lakh No.

0.75) Sixty Nine

Providing and Constructing a Thousand

Conference table top made from Four Hundred

18mm.+18mm.+12mm thick plywood Twenty Three

and between the thickness of top Rupees and

make a grove for 5mm.x5mm. square Fifteen Paisa

S.S. rod for elevation purpose, also Only

6mm. Groove on top for 12 thick

painted glass fitting as shown in

drawing, top rest on 12mm.+12mm.

thick plywood sides covered with

4mm. thick Veneer on both side, front

apron made from 18mm. + 12mm.

thick ply and 6mm. thick painted glass

in elevation as shown in drawing,

above apron made a box from 18mm.

thick ply for electrical/net working

cable running space and plug switches

fitting space and finish with selected

Veneer, including all materials and

labour etc. Complete as per detail

drawing and instruction of Engineer-

In- Charge and Consultant.

10 2.00 Director Table with side table 76,300.00 Seventy Six No.

(2.5x0.90x0.75) Thousand

Providing and fixing 18mm. Three

+18mm.+6mm. thick table top with Hundred

4mm thick Sp. Veneer finish all Rupees Only

around with good quality PU polished

top rested on side boxes with

100mm.x100mm. plywood box

support made out with 18mm.

plywood and finished with white PU

paint as per direction. Two side unit

made out of 18mm. thick plywood

box and back with 6mm. thick

plywood. Side unit finished with

4mm.. thick Sp. Veneer on all exposed

side and fine finished with PU polish

as per direction. The shutter of side

unit made of 18mm. thick plywood

and 4mm. thick Veneer with PU polish

and on sliding channel. All in side

surfaces should be cover with 0.8mm.

thick backing laminate. The side boxes

should be supported with 50mm. dia.

Legs as shown in drawing. The apron

of table made from 18mm+6mm.

plywood and finished with white

colour PU paint on both side and

6mm. clear glass strip of 100mm. in

width should be provided as per

design. And back side drawer unit

made of 18mm. thick plywood box,

shutter and back with 4mm.. thick Sp.

Veneer on all exposed side and fine

finished with PU polish as per

direction. Drawer should be made of

18mm. thick plywood and rested on

good quality auto closed channel.

Back paneling made out of 18mm.

thick plywood covered with 4mm.

thick veneer with PU polish, 6mm.

thick glass strip should be provided as

per design and back paneling should

be continued up to ceiling as shown in

drawing. Work should be carried out

as per detail drawing and necessary

hard ware as per direction and

Engineer-In -Charge and Consultant.

11 1.00 Printer table (0.60x0.60x0.75) 10,094.70 Ten No.

Providing and fixing printer table Thousand

made out of 18mm. Thick ply wood Ninety Four

with 1mm. thick laminate on all Rupees and

exposed side and 0.8mm. thick Seventy Paisa

laminate in side. Printer table top Only

made out of 18mm.+18mm. thick

plywood with 1mm. thick laminate.

The drawer, shutter and facia should

be made of 18mm. thick plywood and

1mm. thick laminate outside and in

side 0.8mm. thick laminate on it.

Edges of the plywood should be

finished with Laminate/PVC/T.W.

patti, with lock and telescopic

channel, S.S. legs and necessary

aluminum profile handle as per detail

drawing Including all materials and

labour etc. complete as per detail

drawing and instruction of engineer-in

charge and consultant.

12 6.30 Low Height Storage 17,646.75 Seventeen Smt.

(1.20x0.45x0.75H) Thousand Six

Providing and fixing Low height Hundred

Storage made out of 18mm. Thick ply Forty Six

wood with 1mm. thick laminate on all Rupees and

exposed side and 0.8mm. thick Seventy Five

laminate in side. Low Height Storage Paisa Only

top made out of 18mm.+18mm. thick

plywood with 1mm. thick laminate.

Two nos. of drawer, shutter and facia

should be made of 18mm. thick

plywood and 1mm. thick laminate

outside and in side 0.8mm. thick

laminate on it. Edges of the plywood

should be finished with

Laminate/PVC/T.W. patti, with lock

S.S. legs and telescopic channel and

necessary aluminum profile handle as

per detail drawing Including all

materials and labour etc. complete as

per detail drawing and instruction of

engineer-in charge and consultant.

13 4.00 Display Unit (1.75X0.90X1.00) 99,304.80 Ninety Nine No.

Providing and Constructing Display Thousand

area made from 18mm. thick ply base Three

and on the top of base cover with Hundred Four

18mm. thick ply and side support as a Rupees and

cover with the same ply, and top of Eighty Paisa

the box cover with 8mm thick acrylic Only

transparent white sheet, and over all

base and top cover with 12mm thick

clear glass box, joint with adhesive

and necessary S. S. clamp, below the

acrylic sheet T5 light fixed in it and

base bottom also LED light fixed on it,

and all plywood side finished with

selected 1mm. Thick laminate and

edge of plywood also finish with

PVC/1mm. thick laminate, as shown in

detail drawing and instruction of

Engineer-In-Charge and Consultant.

14 3.00 High Back Chair-A 18,818.00 Eighteen No.

Providing and supplying Revolving Thousand

synchro tilting mechanism based chair Eight

with gas lift for adjustable height and Hundred

medium curved back with seat and Eighteen

back PU moulded cushion with MS Rupees Only

pipe frame structure and white foam

layer for seat and molded PU foam.

White foam layer for back covered

with thick cloth and draped with cloth

of approved shade. (min. of

Rs.150/meter). 5 legged revolving

molded nylon chair base with good

quality of PU castors with 2 years

replacement guarantee. The chair to

have wide polyurethane arm rest of

approved shape. Complete chair

should be in suitable shape. Rates to

be inclusive of all taxes and free

delivery at site. Selection of

chair,should be as approved by

engineer in-charge and consultant.

15 18.00 Medium Back Chair-C 12,350.00 Twelve No.

Providing and supplying Revolving Thousand

synchro tilting mechanism based chair Three

with gas lift for adjustable height and Hundred Fifty

medium curved back with seat and Rupees Only

back PU moulded cushion with MS

pipe frame structure and white foam

layer for seat and molded PU foam.

White foam layer for back covered

with thick cloth and draped with cloth

of approved shade. (min. of

Rs.150/meter). 5 legged revolving

molded nylon chair base with good

quality of PU castors with 2 years

replacement guarantee. The chair to

have wide polyurethane arm rest of

approved shape. Complete chair

should be in suitable shape. Rates to

be inclusive of all taxes and free

delivery at site. Selection of

chair,should be as approved by

engineer in-charge and consultant.

16 8.00 Low Back Chair-D 7,331.25 Seven No.

Providing and supplying Revolving Thousand

synchro tilting mechanism based chair Three

with gas lift for adjustable height and Hundred

medium curved back with seat and Thirty One

back PU moulded cushion with MS Rupees and

pipe frame structure and white foam Twenty Five

layer for seat and molded PU foam. Paisa Only

White foam layer for back covered

with thick cloth and draped with cloth

of approved shade. (min. of

Rs.150/meter). 5 legged revolving

molded nylon chair base with good

quality of PU castors with 2 years

replacement guarantee. The chair to

have wide polyurethane arm rest of

approved shape. Complete chair

should be in suitable shape. Rates to

be inclusive of all taxes and free

delivery at site. Selection of

chair,should be as approved by

engineer in-charge and consultant.

Providing and Fixing a LOGO made Thousand Six

from S.S. 20gauge sheet, it should be Hundred

in size & shape as per drawing, Rupees Only

shrouding area of the logo, after

designing and plaster work to the

wall. Electrification and spot light

including LED light fixed as per

instruction of the site Engineer-In-

Charge and Consultant

18.1 35.00 Italian Marble Clading 12,259.00 Twelve Smt.

Providing and fixing Italian marble Thousand

cladding on 18mm. thick plywood Two Hundred

board fixed on wall. Plywood should Fifty Nine

be fixed on wall inline and level, Rupees Only

18mm. thick Marble should be fixed

on plywood as per detail drawing with

up down pattern with adhesive with

necessary fittings & fastening as per

design and direction of engineer-in-

charge and consultant.

18.2 8.00 Wall Paneling with Veneer Finish 12,300.00 Twelve Smt.

Wall paneling on wall for electrical Thousand

conducting and net wiring etc. made Three

by 18mm.+18mm. plywood framing, Hundred

Cover with 6mm.+6mm. plywood Rupees Only

fixed, and made grove and 4mm. thick

selected veneer fixed on it with nail

and adhesive material, finished with

PU polish, If necessary paneling

surfaces open able facility with

necessary hardware as per design and

instruction as directed by site

Engineer-in-charge or architect.

18.3 0.90 Decorative Hanging S.S. Plate / 21,269.25 Twenty One Smt.

Colour Acrylic / Wooden Thousand

Providing and Fixing a 2mm. thick S.S. Two Hundred

plate as per cut out design and Sixty Nine

hanging with 1mm. thick S.S. round Rupees and

wire to join S.S. plate to each other Twenty Five

and fixed on top bottom as per design Paisa Only

and directed by Engineer-In-Charge

and Consultant.

18.4 1.00 WORLD MAP (1800MM.X2700MM.) 16,175.90 Sixteen No.

Providing and fixing Colour printed Thousand

world Map (Vinyl Coating) paste on One Hundred

18mm. thick plywood which is fixed Seventy Five

on wall with glue and nail, screw as Rupees and

direction by Engineer-In-Charge and Ninety Paisa

Map Selected by Consultant and Only

Office authority.

18.5 5.00 Design MDF with Duco Paint 13,460.00 Thirteen Smt.

Providing and fixing 18mm. thick Thousand

selected predesigned MDF sheet fixed Four Hundred

on 12mm thick ply wood fixed on wall Sixty Rupees

and finished with selected duco Only

colour paint on design as per drawing

and Drawer unit with facia made out

of 18mm. thick ply finished with duco

paint on outside and inside 0.8mm.

thick laminate finished, necessary

hardware as per instruction of

Engineer-In- Charge and Consultant.

18.6 743.00 Wall Paint 78.44 Seventy Eight Smt.

Wall painting (two) coat with Rupees and

emulsiion paint of approved brand Forty Four

and manufacture under coated wall Paisa Only

surface to give an even shade

including thoroughly. Brusshing the

surace free from mortar dropping and

other foreign matter and sand

papered smooth etc. Complete.

18.7 12.00 Glass Door with Plywood Framing 5,800.00 Five Smt.

Providing and fixing 12mm. thick Thousand

Toughen glass door fixed on floor Eight

spring with necessary selected fitting Hundred

by Consultant, Door gap cover with Rupees Only

18mm. thick plywood box framing

finish with selected 4mm Veneer and

finish with PU polish as directed by

Engineer-In-Charge and Consultant.

19.1 102.46 Wooden and frosted glass partition 7,488.80 Seven Smt.

Providing and fixing 12mm. thick Thousand

toughened glass partition and door Four Hundred

fixed on floor spring, top and bottom Eighty Eight

patch with necessary selected fitting, Rupees and

glass partition fixed on wall, floor & Eighty Paisa

on ceiling side with plywood framing Only

support on plywood partition with

necessary grove and finished with

selected laminate as per detail and

direction of Engineer-In-Charge and

19.2 7.00 Wooden Paneling on LCD Unit 30,415.20 Thirty No.

Providing and fixing an 18mm. thick Thousand

plywood paneling with base of Four Hundred

plywood patti and fixed on it, Fifteen

plywood paneling finished with Rupees and

selected 4mm Veneer with melamine Twenty Paisa

polish, some part cover with selected Only

wall paper with adhesive material,

behind LCD unit wall cover plywood

finished with 6mm. thick painted glass

fixed with adhesive material and

necessary hardware, plywood box

made below the LCD frame and

finished with selected 4mm Veneer

and inside finish with 0.8mm Thk.

Laminit for DVD and Setup box and

LED light fixed as per detail drawing

and direction of Engineer-In-Charge

and Consultant.

20 3.00 Platform Shutter 4,955.35 Four Smt.

Providing and fixing Teak wood frame Thousand

with 18mm. thick plywood shutter Nine

below the plat form (Pantry) with Hundred Fifty

necessary fittings & fastening as per Five Rupees

design and direction of engineer-in- and Thirty

charge and consultant. Five Paisa

21 28.00 Motorized Roller Blind 3,000.00 Three Smt.

Providing and fixing Motorized Roller Thousand

Blinds (HT200) is driven by tubular Rupees Only

motors to lift or down roller blinds. It

is normally suitable for windows from

1.00 mt. To 4.00 mt. Cantenate them

with special connectors (90,135 and

180 degree). It includes the full parts

of roller blinds including selected

fabric, selection by consultant.

technical data i.e. out put voltage12V

DC, Operation Power Consumption

6W, Standby Power Consumption

0.05W, Maximum Remote Distance

12mt., Endurance of the Motor

Approximate 1000 Hrs., Range of the

Curtain 1.00mt to 4.00mt. Maximum

load 3 to 8kg. Fabric, The Motorized

Roller Blind Cover profile finish with

covers, covers up the roller tube and

its fabrics, all work should execute

under the instruction by Engineer-In-

Charge or Consultant.

22 65.00 Manual Roller Blinds 2,350.00 Two Smt.

Providing & Fixing Manual Roller Thousand

Blinds fixed on window, The brake Three

mechanism is designed not to break if Hundred Fifty

attempts are made to lower the blind Rupees Only

by pulling on the bottom rail, the

maximum lifting capacity of the brake

mechanism is 5 kg. Used together

with an Ø36 aluminum tube. The end

plug is locked into the mounting

bracket for secure fastening. The

mounted bracket is made of 1.5mm.

Galvanized steel power coated in

white, distance of the bracket is

36mm from wall to centre. Bottom

bar is made out of aluminum powder

coated in white, the end cap on each

side will match the colour of bottom

bar, and this shape of bottom bar has

been chosen by Consultant who liked

its esthetical appearance. The cover

profile, finished with covers, covers

up the roller tube and its fabrics.

Cover should be made out of

aluminum and is power coated in

white. Fabric should be used as per

selection by Consultant or Engineer-

23 190.00 Gypsum Celing 807.00 Eight Smt.

Providing and fixing gypsum board Hundred

ceiling as per manufactures' Seven Rupees

specifications incl. acrylic paint. Fixing Only

of suspended gypsum plain false

ceiling by using standard company

section (GYPSTEEL R), which includes

providing and fixing G.I. parameter

channels of size 0.55 mm thick having

one flange of 20 mm and another

flange of nylon sleeves and screws at

610 mm center. Then suspending G.I

intermediate channels of size 45 mm,

0.9 mm thick fixed with two flanges of

15 mm each from the sophist at

mm center with ceiling angle of width

25 mm x 10 mm x 0.55 mm thick fixed

to sophist with G.I. cleat and steel

expansion fasteners. Ceiling section of

0.55 mm. thickness having knurled

web of 51.5 mm. and two flanges of

26 mm each with lips of 10.5 mm.

area then fixed to the intermediate

channel with the help of connecting

clips and in direction perpendicular to

the intermediated channel at

mm. center 12.5 mm tapered edge

gypsum board (conforming to is 2095-

1982) is then screw fixed to ceiling

section with 25 mm drywall screws at

230 mm center. Screws fixing is done

mechanically either with screwdriver

or drilling machine with suitable

attachment. Standard company

manufactured section (GYPSTEEL R or

equivalent) should be used for the

entire framework. Finally the board

are to be jointed and finished, so as to

have a flush look which includes filling

and finishing the tapered and square

edges of the boards with jointing

compound, paper tape and two coats

of primer suitable for Gyp-board (as

per recommended practices of India

Gyp or equivalent). Including all

materials and labour etc. complete as

per detail drawing and instruction of

engineer-in charge and consultant.

24 55.00 Ply wood with veneer finish Ceiling 7,786.65 Seven Smt.

Providing and fixing a plywood plain Thousand

false ceiling by using company section Seven

(GYPSTEEL-R) which includes Hundred

providing and fixing parameter Eighty Six

channel of size 0.55mm. thick having Rupees and

one flange of 20mm and another Sixty Five

flange of same as it is previous one Paisa Only

and screws at 610mm. center. Then

suspending G.I. intermediate channels

of size 45mm., 0.9mm thick fixed with

two flanges of 15mm each from the

sophist at 1220 mm. center with

ceiling angle of width 25 mm x 10 mm

x 0.55 mm thick fixed to sophist with

G.I. cleat and steel expansion

fasteners. Ceiling section of 0.55 mm.

thickness having knurled web of

mm. and two flanges of 26 mm each

with lips of 10.5 mm. area then fixed

to the intermediate channel with the

help of connecting clips and in

direction perpendicular to the

intermediated channel at 457 mm.

center 12.5 mm tapered edge gypsum

board (conforming to is 2095-1982) is

then screw fixed to ceiling section

with 25 mm drywall screws at

mm center. Screws fixing is done

mechanically either with screwdriver

or drilling machine with suitable

attachment. Standard company

manufactured section (GYPSTEEL R or

equivalent) should be used for the

entire framework. Finally as per the

design plywood board are to be

jointed and 4mm. thick veneer fixed

on it with PU polished finished, so as

to have a flush look which includes

filling and finishing the tapered and

square edges of the plywood +Veneer

boards with jointing compound

should be fine finished and necessary

lapi and colour/Polish finished, all

materials and labour etc. complete as

per detail drawing and instruction of

engineer-in charge and consultant.

25 2.00 Entrance glass door ( 1.80 m x 2.1 m ) 47,340.00 Forty Seven No.

Providing and fixing a 12mm. thick Thousand

Toughen Glass partition fixed on wall Three

to wall and ceiling/Beam bottom to Hundred

floor fixed glass with aluminum Forty Rupees

anodized frame with cleat and rubber Only

gasket as per drawing and necessary

fixture, Lock, D-Handle, top and

bottom patch, lock and edges of glass

door should be round molded, Gap of

glass should be finished with Silicon

glass should be without any bauble,

and partition should be fixed with

necessary aluminum frame fittings as

per instruction of Engineer-In-Charge

and Consultant.

26 64.00 Floor Carpet (Galicho) 5,606.25 Five Smt.

Providing and Laying a Synthetic Thousand Six

Center Piece floor carpet should be Hundred Six

laying on floor and carpet also Rupees and

selected by Engineer-In-Charge and Twenty Five

Consultant, The floor should be clean Paisa Only

and in levelled, without moisture and

smooth surface, if floor should not be

uneven. It should be work carried out

as per direction of Engineer-In-Charge

and Consultant.

27 8.00 Flower vase-A (Decorative S.S.) 8,050.00 Eight No.

Providing istaling a Flower vase in Thousand

decorative and in good shape made Fifty Rupees

from Stainless Steel with standard Only

company, it should be instaled with

Selected artificial plant as per pot size

and it should be instruction by

Engineer-In-Charge and Consultant.

28 4.00 Flower vase-B (P.V.C / Wooden) 5,175.00 Five No.

Providing istaling a Flower vase in Thousand

decorative and in good shape made One Hundred

from P.V.C./Wooden with standard Seventy Five

company, it should be instaled with Rupees Only

Selected artificial plant as per pot size

and it should be instruction by

Engineer-In-Charge and Consultant.

29 4.00 LCD TV 65,000.00 Sixty Five No.

50 inch LCD Tv Thousand

30 15.00 ALUMINIUM PARTION ( FOR SERVER 1,850.00 One Sqmtr

Providing and fixing aluminium Eight

partition comprising power-coating Hundred Fifty

aluminium framework with 4mm thick Rupees Only

ACP cladding om both side , including

nacessary supports, trims, fastners,

sealents and accessories, complete in

all respects as per approved drawngs

and specification.

LANDSCAPING WORK ITEM

31 200.00 Providing and planting approved 750.00 Seven No.

shrub species, including excavation of Hundred Fifty

pits, soil preparation, supply of Rupees Only

manure, planting, watering,

maintenance, and replacement of

dead plants during maintenance

period, complete as directed by

Engineer-in-Charge. ( Plant Selection

as per design) (Rate may vary as per

32 54.00 Providing, supplying, preparing 1350.00 One Sqmtr

subgrade, spreading approved fertile Thousand

topsoil (150 mm thick), supplying and Three

mixing organic manure, fine dressing, Hundred Fifty

leveling, watering, and laying Rupees only

approved Mexican/Korean grass turf

complete as per specifications,

including maintenance and

replacement of damaged grass during

maintenance period. ( Lawn Selection

as per design) (Rate may vary as per

33 35.00 Providing and placing approved 4000.00 Four No.

decorative planter/pot of specified Thousand

size and material Rupees only

(FRP/Ceramic/Cement/Metal),

including supply of approved plant

species, potting mixture (good earth,

sand, cocopeat,

vermicompost/manure), planting,

watering, shifting to designated

location, maintenance, and

replacement of dead plants during

maintenance period, complete as per

approved design and direction of

Engineer-in-Charge. ( At Terrace level,

Plant and pot selection as per

Total Cost of All Work

Say Total Value of Work

[Rupees Sixty five Lakh Thirty two Thousand Four Hundred Seventy Two Rupees and Zero Paisa Only.]

I/We am/are willing to carry out the work at ……………………………………… % above / below percent [should be

written in figures and words] of the estimated rates mentioned above. Above of my / our tender works out as under.

Estimated Amount Estimated Amount

Put to tender Rs. ……………………………….. Put to tender Rs. …………………………

In words …………………………………..… In words ………………

[Please strike out whichever is not applicable]

[1] The Contractor shall exhibit a board with detailed specification and details of work as

directed by the Engineer-In-Charge for which no extra payment shall be made.

[2] The Labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

[3] GST and Income tax TDS will be deducted at a source while making payments of bills

Signature of Bidder Chief Executive Officer Commissioner Civil Aviation

GUJSAIL Govt of Gujarat