DAY TO DAY MAINTENANCE OF PLUMBING, SANITARY ITEMS, BATH FITTINGS, FALSE CEILING, TILLING WORKS AND OTHER B/R WORKS AT OTM ACCN UNDER GE (NORTH) TEZPUR

Amount

M & L for seven stage cleaning and sterilization of inside and outside of overhead PVC service tank of exc 250 but n. exc 500 liters capacity through bacteriological treatmentby using TERBAC GS, TERBAC-G-65 and ultra violet ray. First stage: Drain out the water by using exist valve or high capacity dewatering system without disturbing the other material/item. Second stage: Claen th all algae formation inside the tank by using TERBAC G 10, a laboratory tested branded chemical of the company and scrubbing the walls of the tank. Third stage : Clean the tank with fresh water by high speed jet pump.. Fourth Stage: Bacteria screening by decertification using TERBAC-G5, a Govt laboratotory certified branded halogen compound. Fifth stage: Cleaning the floor of water tank by industrial vaccum cleaner. Sixth stage: Second bacteria screening and sterilizing method by using ultra violet ray within the tank and kills all suspended bacteria. Seventh stage: Cleaning and third bacteria screening is to sterilize the floor of the water tank by using laboratory certified, branded strong oxidizing agent TERBAC-G65. Note: Cost of staging and necessary working platform shall deemed to be included in quoted rate. Contracor shall ensure necessary safety precaution and insurance of workers during execution. The quoted rates shall deemed to be included the cost of writing date of cleaning, due date and capacity of tank shall be mentioned over tank complete all as specified and as directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed

Taking down wooden door shutter area exceeding 1.00 but not exceeding 2.00 sqm each complete all as specified and as directed.

Taking down wooden door shutter area not exceeding 1.00 sqm each complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed by Engineer in charge.

M & L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M & L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

M & L for seven stage cleaning and sterilization of inside and outside of overhead PVC service tank of 1000 liters capacity through bacteriological treatmentby using TERBAC GS, TERBAC-G-65 and ultra violet ray. First stage: Drain out the water by using exist valve or high capacity dewatering system without disturbing the other material/item. Second stage: Claen th all algae formation inside the tank by using TERBAC G 10, a laboratory tested branded chemical of the company and scrubbing the walls of the tank. Third stage : Clean the tank with fresh water by high speed jet pump.. Fourth Stage: Bacteria screening by decertification using TERBAC-G5, a Govt laboratotory certified branded halogen compound. Fifth stage: Cleaning the floor of water tank by industrial vaccum cleaner. Sixth stage: Second bacteria screening and sterilizing method by using ultra violet ray within the tank and kills all suspended bacteria. Seventh stage: Cleaning and third bacteria screening is to sterilize the floor of the water tank by using laboratory certified, branded strong oxidizing agent TERBAC-G65. Note: Cost of staging and necessary working platform shall deemed to be included in quoted rate. Contracor shall ensure necessary safety precaution and insurance of workers during execution. The quoted rates shall deemed to be included the cost of writing date of cleaning, due date and capacity of tank shall be mentioned over tank.

Supply and fixed in position two layered ISI marked rotational moulded polyethylene water storage tanks of 500 litres capacity (cylindrical vertical with closed top) including cover, using new GI tank/PPR or other type of material tank nipples and unions for inlet and outlet pipe connection of same internal bore dia. and one for cleaning with dead plug , including dismantling and taking down of old unserviceable water storage tank complete in all respect as specified and directed.

Supply and fixed in position two layered ISI marked rotational moulded polyethylene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) including cover, using new GI tank/PPR or other type of material tank nipples and unions for inlet and outlet pipe connection of same internal bore dia. and one for cleaning with dead plug , including dismantling and taking down of old unserviceable water storage tank complete in all respect as specified and directed.

Supply and fixed 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and bitumen washers or with J hook etc. , in roofs, walls etc. with grade of zinc coating 275 including dismantling and taking down existing steel sheeting of any guage/thickness, including Nainital or similar pattern roof covering complete in all respect as specified and directed.

Fixing only existing galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and bitumen washers or with J hook etc. of any thickness, in roofs, walls etc. with grade of zinc coating 275 including dismantling and taking down of existing steel sheeting of any guage/thickness, including Nainital or similar pattern roof covering complete in all respect as specified and directed.

Supply and fixed Plain galvanised mild steel sheeting 0.63 mm thick as in ridges, hips, valley gutters of any shape and size, drip and straight flashing (length and girth as fixed) with grade of zinc coating 275 micron etc. including dismantling and taking down of any guage, thickness, including Nainital or similar pattern complete in all respect as specified and directed.

Supply and fixed 6 mm thick Asbestos Cement, corrugated or semi-corrugated sheets in roofs, walls etc. and fixed with L-type or J-type or cranked hook bolts etc. including dismantling and taking down Asbestos cement (corrugated, semi-corrugated, etc.) sheets complete in all respect as specified and directed.

Fixing only 6 mm thick Asbestos Cement, corrugated or semi-corrugated sheets in roofs, walls etc. and fixed with L-type or J-type or cranked hook bolts etc. including dismantling and taking down Asbestos cement (corrugated, semi-corrugated, etc.) sheets complete in all respect as specified and directed.

Supply and fixed in repairs 4mm thick Asbestos Cement plain building boards for ceiling in flat or sloping fixed to timber framework with screws etc. including preparation of new asbestos surfaces of ceiling and apply two coats of white wash including preparation of surface complete in all respect as specified and directed.

M & L for structural timbers of group B, first or second choice as per IS 3629: 1986 in fillets, square, rectangular or triangular in section, clean sawn, secured with screw, area exceeding 6 sqcm but not exceeding 13 sqcm complete all as specified and as directed.

S & F for coloured glazed pre coated chequered cement concrete tiles of any shape and size, 20-25mm thick with grey cement with pigment,; set jointed and pointed in neat cement slurry with pigment in floors including over 15mm thick screed bed in CM 1:4 and dismantalling of existing tiling with screed bedding complete in all respect as specified and directed.

Supply and fixed for glazed ceramic tiles 7 to 8 mm thick (square/rectangular) in vertical surface, area of each tile exceeding 0.06 sqm but not exc 0.16 sqm, set, jointed and pointed in neat cement slurry and pointed in white cement with pigment to match the tile colour over 15mm thick rendering in cement sand mortar 1:4 including dismantalling of existing tiles with screed bed/plastering complete in all respect as specified and directed.

Supply and fixed for ceramic floor tiles 7 to 8 mm thick (square/rectangular) in flooring, area of each tile exceeding 0.08 sqm but not exc 0.16 sqm set and jointed in neat cement slurry and pointed in white cement with pigment to match the tile colour over 15mm thick screed bedding in cement sand mortar (1:6) including dismantalling of existing tiles with screed bed/plastering complete in all respect as specified and directed.

Material and labour for 25mm cement concrete type B-0, 1:2:4 (using 12.5 mm crushed and graded stoone aggregate) in flooring and finishing the cement concrete surface even and smooth without using extra cement including dismanatlling of existing PCC floor complete in all respect as specified and directed.

Supply and fixed plain sheet glass 4 mm thick, ordinary quality and glazing with oil putty or in wooden frmae with new wooden beadings in square/rectangular or of any shape not exc. 0.5 sqm in each pane etc. including hacking out old glasses complete in all respect as specified and directed.

Supply and fixed in repair figured glass 4mm thick, pin head type and glazing with oil putty or in wooden frmae with new wooden beadings in square/rectangular or of any shape not exc. 0.5 sqm in each pane etc. including hacking out old glasses complete in all respect as specified and directed.

Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water complete all as specified and as directed.

Material and labour for plastering 15 mm thick on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for plastering 15 mm thick on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

S & F in repairs mild steel door spring of rat tail type of size 300 mm, bright finish including roller and roller plate complete all as specified and as directed.

S & F in repairs 20 mm dia harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed.

S & F in repairs aluminium anodised tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and as directed.

S & F in repairs galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised steel wire staples complete all as specified and as directed.

Supply and fixed in repair plain sheet glass 4 mm thick, ordinary quality and glazing with oil putty or in wooden frmae with new wooden beadings in square/rectangular or of any shape not exc. 0.5 sqm in each pane etc. including hacking out old glasses complete in all respect as specified and directed.

S & F 32 in repairs mm nominal size, copper alloy, nickel chromium plated finish waste fittings with including silicone sealant complete all as specified and as directed.

S & F in repairs 10 litres capacity, low level, syphonic type, white, plastic flushing cistern as per IS 7231: 1994 with inlet, ball valve, float and handle including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with brass chromium plated bracket guard and railing 60 cm long complete in all respect as specified and directed.

S&F in repair toilet paper holder of cast copper alloy chromium plated fixed to walls with chromium plated (CP) brass screws complete in all respect as specified and directed. Make:- Jaquar Cat Part No. AEC-1151, Cera, Cat Part No. F5002109 or equivalent make in Hindware

S & F in repairs in repairs thermoplastic seats and covers of grade 2 type, flat with hinging device of bronze or brass with nickel chromium plating complete all as specified and as directed.

Attending day to day complaints for petty repairs to leakage of bib taps, pillar cock, stop cock, waste pipes, float valves, angle valve, concealed valve, GI union, joints of GI pipe, re-fixing of bottle trap, wash hand basin, wall mixer, WHB mixer etc, by changing the PVC washers/,Sheet washers, cistern leaking/adjustments or any other minor accessories etc complete in all respect as specified and directed. NOTE:-Minimun two plumbers alongwith with two helpers with necessary tool and plant shall be provided by contractor per day to attend the complaint, and the complaint for the attended qtr is valid for two months, if complaint re-registred the same will be carried out without any extra cost to the deapartment , the printed complaint book duly serially numbered for this will be provided by the contractor, if complaints are registered more, the men power will be increased by the contractor, the rates for these are deemed to include in the quoted rates.Failure to complete the job within 24 hrs, penality of Rs 200 per day per complaint will be recovered from the contractor till the date of completion)

Attending day to day complaints for petty repairs to door, window, cup board, such as adjusting to tower bolt, handle, sliding door bolt, easy to door/window/ventilators complete in all respect as specified and directed. NOTE:-Minimun two carpenters alongwith with two helpers with necessary tool and plant shall be provided by contractor per day to attend the complaint, and the complaint for the attended qtr is valid for two months, if complaint re-registred the same will be carried out without any extra cost to the deapartment , the printed complaint book duly serial numbered for this will be provided by the contractor, if complaints are registered more, the more tradesmen will be increased by the contractor, the rates for these are deemed to include in the quoted rates. Failure to complete the job within 24 hrs, penality of Rs 200 per day per complaint will be recovered from the contractor till the date of completion)

S & F in repair Pedestal stand with Wash hand basins, vitreous China of size 550 x400mmX800mm(flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32mm dia bore waste fitings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, PVC waste pipe including 15mm bore dia fancy type CP finish Pillar tap, cast copper alloy with capstan heads, screwed down high presuure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipes complete in all respect as specified and directed. Make Hindware, Cat Part No. 10098, 11032(WHB with pedestal), Cat Part No. F730001(Pillar Cock) Cat Part No. F860010 (Waste coupling 32mmSS) or equivalent make of Jaquar, Marc, Prayag.

S & F in repairs grating square 150 mm size of PTMT (Minimum weight 100 gms) complete all as specified and as directed.

S & F in repairs prelaminated particle board (decorative lamination on both sides), 12 mm thick, grade I or II & type II (Designation PLB-12 or PLB-22), made out of medium density particle board (flat pressed-three layer or multilayer and graded (grade I or grade II), bonded with BWR adhesive), fixed with screws to timber/ steel frame work for horizontal applications as in table tops, counter, furniture tops, etc. complete all as specified and as directed.

Supply and lay high density polyethylene pipe (HDPE) of pressure rating PN 6(0.6 Mpa), material grade PE 63 and nominal dia 32 mm including all fittings and fixtures in trenches complete all as specified and as directed.

S & F in repairs 15 mm nominal size, nonrising spindle type fancy pillar taps as per IS 8931: 1993, cast copper alloy body with knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

S & F in repairs bib tap standard of PTMT, any colour, high pressure, minimum weight 90 grams, screwed for steel tube for nominal size 15 mm complete all as specified and as directed.

S & F in repairs 15 mm nominal size, nonrising spindle type fancy bib taps as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, bright finish complete all as specified and as directed.

S & F in repairs 15 mm nominal size, nonrising spindle type fancy angle stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

S & F in repairs 15 mm nominal size, nonrising spindle type fancy stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

S & F in repairs stop valves of PTMT, any colour, high pressure, minimum weight 90 grams, screwed for steel tube for nominal size 15 mm complete all as specified and as directed.

Supplying & laying in trenches 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & laying in trenches 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

S & F in repairs ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 20 mm size, minimum weight 210 grams complete all as specified and as directed by the Engineer-in-Charge.

M & L in repairs for PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

M & L in repairs for PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

S & F in repairs mild steel sliding door bolts, type I (plate type), size 250 mm, stove enamelled black finish to back plate, straps and staple, electroplated finish with nickel and chromium to hasp and bolt, bolt not less than 12 mm dia with and including a minimum

S & F in repairs 200 mm size, mild steel barrel tower bolts with mild steel barrel and mild steel bolt, dia of bolt 10 mm, bolt finished bright, other parts finished stove enamelled black complete all as specified and as directed.

S & F in repairs mild steel handle, pressed half oval type, 125 mm size, stove enamelled black finish complete all as specified and as directed.

S & F in repairs heavy weight stainless steel butt Hinges, 100 mm size, naturally finished bright with smooth surface without chemical coating complete all as specified and as directed.

S & F in repairs heavy weight stainless steel butt Hinges, 75 mm size, naturally finished bright with smooth surface without chemical coating complete all as specified and as directed.

S & F in repairs semi rigid PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm connected to waste fittings complete all as specified and as directed.

S & F in repairs semi rigid PVC waste pipe for sink and wash basin 40 mm dia with length not less than 700 mm connected to waste fittings complete all as specified and as directed.

Supply only M-Seal in sealed packets to the AGE B/R North store complete all as specified and directed.

Supply only white cement in 1 Kg packing to the AGE B/R North store complete all as specified and directed.

S & F steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and as directed.

Material and labour for preparation of newly undecorated plastered surface of wall and applying three coats of cement based paint over one coat of alkali resistant priming paint including filling of voids/surface with wall care putty on plastered surface complete in all respect as specified and directed.

S&F In repairs CP finish cast copper alloy, two way bib tap with Health Faucet 15 mm dia fancy type with 1.00 mtr tube and hook complete in all respect as specified and directed.

Material and labour for preparation of newly undecorated plastered surface of wall and applying two coats of oil bound distemper and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2mm thick (in two layers), wall care putty complete in all respect as specified and directed.

Material and labour for complete removal of existing treatment on wall and applying two coats of oil bound distemper and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2mm thick (in two layers), wall care putty complete in all respect as specified and directed.

Supply and Fix exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping , of grid size 600x600mm comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 24x38x0.70mm with 4mm dia GI wire as suspender and including 4mm thick decorative pre -painted non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/wooden truss of any type including dismantalling of existing false ceiling complete all as specified and directed. (Make: Eternit, Everest or equivalent)

Material and labour for complete removal of existing treatment over walls and applying two coat of weather coat over 3mm thick wall care putty (in two layers) and a coat of primer including rubbing etc. and all necessary preperation complete in all respect as specified and directed.

S&F 2nd class Hard wood scanttlings, wrought in any position for framed work jointing wirh nails, screws, nut bolt etc. including necessary supports to existing truss including Dismantling of timber scanttlings 40 Sqcm & over in section, in any position for framed workcomplete all as specified and directed.

M & L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with one coat of creosote complete all as specified and as directed.

Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge

S & F flush door shutters, 35 mm thick, solid core of block boards construction, MR grade, commercial type with stiles, rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1): 1999, both sides face panels of plywood as per IS 710: 2010, internally lipped complete all as specified and as directed.

Supply and fix solid PVC door frames of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube all as per specification & drawing complete all as specified and directed by Engineer in charge.

Providing and fixing 30 mm thick factory made solid panel PVC door shutter as per IS 15931: 2012 with 19 gauge thickness mild steel tube and tapering 20 mm in 45⁰ angle on both sides forming styles and on the inner side to form top and bottom rail and on both sides to form lock rail complete all as specified and as directed.

M & L for second class HW Glazed and skeleton shutters for doors of 35 mm thickness, open rebated and prepared to received glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a)

S & F hot rolled medium and high tensile structural steel of grade E 250 quality A conforming to IS 2062: 2011 as in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20 mm of the length indicated) complete all as specified and as directed.

Supply & fix sheet glass, ordinary quality, 4 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F in repair PVC cover for 500liter capacity water storage tanks of any description and any shape including PVC locking arragement complete in all respect as specified and directed.

S&F in repair PVC cover for 1000liter capacity water storage tanks of any description and any shape including PVC locking arragement complete in all respect as specified and directed.

S & F 75 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed.

S & F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 150 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed.

S & F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 100 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed.

S & F cast aluminium alloy handle, cast type, 150 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.

S & F cast aluminium alloy handle, cast type, 125 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.

S & F aluminium alloy sliding door bolts with hasp, staple and fixing clips of sheets, or extruded sections and fixing bolts and sliding bolts of extruded sections of aluminium alloy, 300 mm long, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.

M & L for cement concrete M15 (Nominal Mix) using 40 mm nominal size graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs, slab staging for water tanks, filling of pressed steel door frame, fixing of hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formworks complete all as specified and directed by Engineer-in-charge.

S&F coloured 0.50mm thick pre- painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws with bitumen washer to truss, rafter, purlin etc. members of any type of material including dismatalling of existing sheets complete in all respect as specifified and directed.

S & F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in eves covering, ridges or of similar type, fixed with self tapping screws including necessary mild steel flats and screws for fixing with framed structure complete in all respect as specifified and directed.

S & F hot rolled medium and high tensile structural steel of grade E 250 quality C conforming to IS 2062: 2011 as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed.

Preparation of newly plastered surfaces on walls and applying two coats of white wash complete all as specified and as directed.

S & F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S & F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F in repairs of laying Bitumen Tarfelt weighing 1.5 Kg/Sqm on AC/ CGI roof sheets in any position with self adhesive/ bitumen coated complete all as specified and directed. Make: M/s Sika Pvt Limited, M/S STP ltd, M/s Pidilite.

D G Corporation

M/S Barua Enterprise

M/s Brahamaputra Wood Industries

Anil Kumar Sarmah

DRISTEE ASSOCIATES

M/S Inder SINGH SABARWALL

M/S KAUSHICK CONSTRUCTION