374/G/BSP 2/2nd call/dated 28.10.2026

Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

In all types of soils.

Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work.

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size).

Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:

Cement Mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing flush door shutters, conforming to IS : 2202 (Part-I), decorative type core of block board construction with frame of first class hard wood and well matched teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters excluding hinges.

30 mm. thick (single leaf)

Providing and fixing commercial grade water proof ply for wall paneling on wooden frame with necessary nails complete as required.

Providing and fixing approved shade veneering on wood wall paneling complete as required.

Providing and fixing antique/ SS finished brass butt hinges with antique/ SS polished MS screw complete:

125x85x5.50mm (Heavy Type)

120x85x5.50mm (Heavy Type)

Providing and fixing factory made PVC door shutters of specified thickness made of styles and rails of a UPVC hollow section of specified size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the comers by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws.

24 mm thick door shutters with styles and rails of size 59x24 mm

Steel work in tubular (round, square or rectangular hollow tubes etc.) structure in built-up sections, trusses and frame work including cutting, hoisting, fixing in position upto a height of 5m above plinth level, consisting of columns trusses, roof and bottom purlins, base plate, holding down bolts, wind ties bracing (if required), bolts, nuts and washers for fastening etc. complete with applying a priming coat of red oxide zinc chromate primer.

Electric resistance or induction butt welded tubes Grade-250

Electric resistance or induction butt welded tubes Grade-300

Providing and fixing M.S. frames of doors, windows, ventilators and cupboards joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10cm of grade M-10 or with wooden plugs and screws or with dash fastener or rawl plugs and screws or with fixing clips or with bolts and nuts as required including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Angle-iron frames

Providing and fixing stainless wire gauge of average width of aperture 1.56mm with wire of 0.35mm to existing steel door, window shutter frames with necessary M.S. strip beading etc. complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately:

For fixed portion

For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/neoprene gasket required (Fittings shall be paid for separately).

Extra for powder coated (minimum 50 micron) aluminium section instead of anodized.

Providing and fixing 12mm thick pre-laminated particle board flat pressed with decorative lamination and balancing lamination on specified sides exterior Grade - I MDF Board 12 mm thick confirming to IS: 14587, including fixed in aluminium doors, windows shutters and partition frames with C.P. brass/ stainless steel screws etc. complete.

With decorative lamination on both side

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness

Extra for providing and fixing tinted glass panes in aluminium door, window, ventilator shutters and partitions instead of float glass.

5 mm thickness

Providing and fixing aluminium composite panels in approved panel sizes, thickness and shape on aluminium frame work on face of building. (Frame to be paid separately)

4mm thick

Providing and fixing clear float toughened glass door or partition in required thickness frameless in appropriated sizes inclusive of edge molding polish and making required size slot or hole for patch fitting/hardware etc. The glass to be assembled together with patch fitting and hardware in proper alignment with all labour tools and tackles etc. complete. (Patch fittings and hardware to be paid for separately).

12 mm thick for door/partition

Providing and fixing of stainless steel grade 316 patch fitting and hardware or apporved (Hardwyn, Ozone, Godrej) make in frame les toughened glass door or partition in proper alignment with all tools tackless and labour etc complete.

Top Patch with SS grade 304

Top/Side patch glass or L-Connector patch SS grade 304

Bottom Patch to be connected with floor machine

Bottom Lock Patch with three key SS grade 304

Corner atch fitting with pivot SS grade 304

H type handle 32x600mm SS 304 grade

Floor/Wass to Glass Connector SS grade 304

Supply and fixing of precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing at all height false ceiling consisting of frame work "W" / "U" / "L" sections made of G.I. sheet with zinc coating of grade 120 consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.55mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed including providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part-I all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting.

In Cement Mortar 1:6 (1 cement : 6 fine sand)

Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix:

In Cement Mortar 1:6 (1 cement : 6 fine sand)

Cement concrete flooring with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm) finished with a floating coat of neat cement.

40 mm thick

50 mm thick

Providing and fixing rectified glazed ceramic Floor tiles of 1st quality conforming to IS : 15622-2017 of approved make, in all colours, shades over 20mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete.

Size 300x300mm thickness 7 to 8 mm

Size 400x400mm thickness 7 to 8mm

Providing and fixing rectified glazed ceramic wall/dado tiles of 1st quality conforming to IS : 15622-2017 of approved make, in all colours, shades on wall and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete.

Size 300x450mm thickness 7 to 8mm

Providing and laying Matt/Glazed finish HOMOGENEOUS ACROSS FULL BODY VITRIFIED floor tiles (heavy duty) with water absorption less than 0.05% and conforming to IS : 15622-2017 of 1st quality of approved make in all colours and shades and size mentioned below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.

Size 600x600mm thickness 9 to 10mm

Providing and laying DOUBLE/ MUTLTI CHARGE (minimum 2.0mm thick layer) VITRIFIED floor tiles with water absorption less than 0.05% and conforming to IS : 15622-2017 of 1st quality of approved make in all colours and shades and size mentioned below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.

Size 600x600mm thickness 9 to 10mm

Size 1000x1000mm thickness 10 to 12mm

Providing and fixing 15mm thick Granite (machine cut, table rubbed & mirror polished on both sides) for partition curtain in toilets or similar locations of required size in wall with cement mortar 1:4 (1 cement : 4 coarse sand) including cutting chase in wall and joint with wall treated with white cement mixed with matching pigment including nibbing and polishing to edge moulding to give high gloss finish.

Granite stone lakha red/ shahi red

Extra for providing edge moulding to 15mm thick stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work

White washing/ Colour washing with lime to give an even shade in Three or more Coats for New surface as per relevant IS code 6278:1971 Consumption of lime 3.50kg /10 Sqm with all tools tackles and labour etc. complete for the work.

Providing and applying plaster of paris putty over plastered wall surface including scaffolding complete

Upto 2 mm thickness to make surface even and smooth in line and level.

Providing and applying for renewing the existing putty/paint surface with white cement based polymeric exterior grade putty for one or more coats applied @ 1.50 kg/ 10Sqm as per relevant I.S. code 17545:2021 (Product such as Birla wall care, Asian trucare, JK wall putty, Berger Bison wall putty) to make the surface smooth and even with all tools tackles and labour etc. complete for the work.

Providing and applying rencwing with Synthatic oil bound washable Distemper having VOC content less than 50gms/ lit. as per relevant 1.S. Code 428:2000 (product such as Asian Tractor synthatic distemper , Berger Bison Lite Dulux A100, Birla Opus Style super smart) inclusive of providing abro tape on cdges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work.

Two coats up to final finish to give an even shade applied 0.75 kg / 10Sqm

Providing and applying for renewing with Premium plastic emulsion paint with roller application as per relevant I.S. Code 15489:2013 Type -1 Class D & C ( Glossy and Semi Glossy Finish) of required shade (Product such as Asian Apcolite Premium ,Dulux Super Cover, Berger Easy Clean, Nippon Breezee Metex Gold, Opus I-50 / Calista) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work.

Two coats applied @0.75 lit /10Sqm up to final finish

Providing and applying for renewing on exterior surface with PREMIUM Exterior emulsion paint_of required shade to give protective and water proof finish as per relevant I.S. Code 15489:2013_Type -2 Class D , C (Glossy /Semi Glossy finish) (Product such as Asian Apex ,Dulux Weather Shield Prima E900, Berger Weathercoat Antidust, Nerolac Everlas Excel ,Nippon Sumo Etra, Opus True flex) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour ete. complete for the work

Two coats applicd (@ 0.75lit / 10Sqm up to final finish

Demolishing brick masonry including arches, stacking of serviceable material disposal of unserviceable material within 50 metres lead.

In cement mortar.

Dismantling doors chowkhats with shutters (steel or wood) including architrave, hold fast etc. complete and stacking within 50 metres lead

Dismantling windows chowkhats with shutters (steel or wood) including architrave, hold fast etc. complete and stacking within 50 metres lead..

Taking out door shutters (steel or wood) including stacking within 50 metres lead.

Dismantling terrazzo or mosaic or glazed vitreous or patent cement or tiled flooring or dado skirting of any thickness without sub base.

Demolishing cement concrete including disposal of material within 50 metre lead.

1:4:8 or leaner mix

Providing and fixing water closet squatting pan (Indian type W.C. pan ), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) conforming to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required :

White Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing 10 litre capacity P.V.C. low level flushing cistern conforming to IS : 7231, with all fittings and fixtures complete.

White

Providing and fixing ISI marked plastic seat with lid for pedestal type W.C. pan complete:

White/ black

Providing and fixing 15 mm nominal bore uplasticised PVC connection pipe with PTMT nuts and PVC bush of approved quality and colour:

30 CM length

45 CM length

Providing and fixing white vitreous china urinal basin with waste fitting as per IS : 2556, and other couplings in C.P. brass complete:

Flat back half stall urinal of size 460x380x250mm

Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required :

White Size 550x450 mm

Providing and fixing vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

White

Providing and fixing stainless steel AISI-304(18/8) wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required :

Size 510x410 mm

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink without drain board as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required :

560x410 mm bowl depth 215 mm.

Providing and fixing PVC waste coupling in wash basin/ sink.

Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete.

75 mm dia pipe.

110 mm dia pipe.

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

Tee/Tee with door/Bend 45 /Bend 90

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required :

15 mm nominal bore.

20 mm nominal bore.

Providing and fixing 15 mm nominal bore Brass bib/stop cock of approved quality:

Bib cock (350 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:

Bib cock (400 grams)

Long nose bib cock (500 grams)

Long body bib cock (500 grams)

Piller Cock (400 grams)

Two way bib cock (800 grams)

Angle valve for basin mixer and geyser points (450 grams)

Wall mixer with elegant knob (1400 grams)

Shower rose (revolving type) (150mm)

Towel rail (600mm long x 20mm dia)

Wall mixer (telephonic type) with crutch arrangement for hand shower (1400gms)

Health foscet (hand jet) with flexible connection pipe (for WC)

CP brass water jet to be fixed in seat cover of WC with flexible connection pipe

Providing and fixing stainless steel drain jali of approved make/quality.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

15 mm nominal bore

20 mm nominal bore

Providing and fixing gun metal non- return valve (horizontal type) of approved quality (screwed end):

25 mm nominal bore

Providing and fixing gun metal non- return valve (vertical type) of approved quality (screwed end):

25 mm nominal bore

UOM Name

Percentage

Per mile

Siemens Per meter

Activity unit