WBPWD/EE/PED/NIQ19_2nd Call /2020-2021

Amount

S&F 415V, 200 A TPN SDF in SS enclosure with HRC fuse (L&T Make cat no. SK90488) on angle iron frame on wall incl. mending good damages and painting.[NS]

S & Installation Cubical LT panel board fabricated by necessary acessories incl interconnection of following aces :- Incoming :- i) 415 v, 200 A TPN SFU main switch FN type - 1 set [ Make:- L&T make] ii) 415 V, 315 A [Cu bars, [800 mm long] 4 x 40 x 5mm] Outgoing i) 415 v, 125 A TPN SFU main switch - 3 set ( L&T make) ii) 240v, 32 A TPN SFU main switch - 3 set for spare. ( L&T make) iii) 0-500v voltmeter Digital - 1 no iv) RYB LED lamp - 3 nos v) EI Danger Board - 1 no The above should have suitable size cable end/ Throat box arrangement,interconnection by cu. wire socketing ends & painting. All fabrication & internal should be done as per direction by EIC. [NS]

S&F 40 cm. X40 cm.x 20 cm. Sheet metal box(16SWG) with hinged type door incl. locking arrangement concealed in wall with necy. earthing attachment incl. mending good damages and painting and S&F one no of 3 pole power contactor (L&T Make ML-2) , 240V AC Analog time switch (L&T cat no J648B1), one no of 32A TPN MCB and 4 nos of 10A SPMCB(Havells Make) fitted With Auto-Off-Manual switch, one no of 3A SPMCB for control in the box, interconnection to be Made with suitable size of copper wire as per direction of EIC.(NS)

Supplying and fixing double door Vertical TPN MCB Distribution board for MCCB incomer with IP-42/43 protection, on angle iron frame on wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment. [D-11/15]

Upto160A, 8 way, Make:-Legrand

Supplying and fixing double door Horizontal TPN MCB Distribution board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment.[D-10/14]

4 way, Make:-Legrand

Supplying and fixing double-door SPN MCB Distribution Board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment.[D-9/13]

2+12 way, Make:-Legrand

S/F 32 A TPNMCB with FP enclosure. [ Legrand] [D-9/11 + D-7/8]

Supplying and fixing 415 V Four Pole MCCB of Breaking capacity 25kA/35kA with fixed thermal and fixed magnetic / adjustable thermal and fixed magnetic setting in existing DBs / enclosure and necessary connection

160 A Make:-Legrand [D-8/10]

Supplying and fixing 240/415 V MCB Isolator on din rail of existing DBs and necessary connection.

63A, FP Make:- Legrand for PDB [D-5/6]

40A , DP Make:-Legrand for SPNDB [D-5/6]

Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection

63 A, TP, Make:- Legrand for VTPN [D-6/7]

32 A, TP, Make:- Legrand for VTPN [D-6/7]

32 A, SP, Make:- Legrand for 9 nos VTPN and 4 nos PDB [D-6/7]

25 A, SP, Make:- Legrand for PDB [D-6/7]

10 A, SP, Make:- Legrand for SPNDB [D-6/7]

6 A, SP, Make:- Legrand for SPNDB [D-6/7]

Supply of 1.1 KV Gr.PVC/Al./A. Cable Make (Gloster/Polycab) [NS]

3.5 core 95 sqmm cable [NS]

3.5 core 70 sqmm cable for VTPN [NS]

2 core 6 sqmm cable for Street light [NS]

Laying of cable above 3½ core 50 sqmm and upto 3½ core 90 sqmm on wall/surface including S & F MS clams with earthing attachment in 2 x 10 SWG GI (Hot Dip) Wire, making hole etc. as necy., mending good damages and painting. [F-1/2(d)]

Laying of cable upto 2/3/4 core upto 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 2 x 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting. [F-1/2(b)]

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below : [F-4/7]

for 2 Core upto 6 sqmm [F-4/7(a)]

for 3.5 Core upto 70 sqmm [F-4/7(d)]

for 3.5 core upto 95 sqmm F-4/7(d)

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials [F-5/8(b)]

2 core 6 sqmm cable [F-5/8(b)(ii)]

3.5 core 70 sqmm cable [F-5/8(b)(xvii)]

3½ core 95 sqmm cable [F-5/8(b)(xviii)]

Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (brand polycab/Havells) partly in 20mm size PVC rigid conduit 'FR' (Brand approved by EIC) [for horizontal run & above false ceiling portion only] and in 19mm bore, 3mm thick polythene pipe [for vertical run embedded in wall], with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board on wall complete with 2 no. “Ph & N” copper bar incl. bakelite/ Perspex top cover 3 mm thick and incl. 175x100x65mm inspection box, making earthing attachment, painting the MS box and mending good the damages to original finish [PVC Rigid Conduit only for horizontal run & above false ceiling and vertical run concealed]

Average run 8 mtr [E-16/6(c)]

On Board 2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC. [E-10/4(a)(i)]

Supply & Fixing 240 V, 2 nos. 6A, & 2 nos. 20A plug socket with separate 2 nos. 6 A & 2 nos. 20A Piano key type switch, indicator & 20A switch type SP MCB (Brand Anchor) on sheet metal switch board embedded in wall incl. S & F 240 x 200 x 65mm MS (16SWG) switch board andbakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required. [E-7/28]

Supply & Fixing 240 V, 20A, plug socket with separate 20 A Piano key type switch (Brand Anchor) on sheet metal switch board embedded in wall incl. S & F 150x100x65mm MS (16SWG) switch board andbakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required. [E-6/22]

Distribution wiring in 1.1 KV single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 25/20mm size PVC rigid conduit 'FR' (Precision make) incl. necy.fittings as required

2 x 36/0.3 (2.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC. [E-14/1(a)(ii)]

2 x 84/0.3 (6 sqmm) + 1 x 56/0.3 (4 sqmm) ECC for SPNDB [E-14/1(a)(iv)]

4 x 56/0.3 (4 sqmm) + 2 x 36/0.3 (2.5 sqmm) ECC for TPN Enc [E-14/1(b)(iii)]

4 x 80/0.4 (10 sqmm) + 2 x 84/0.3 (6 sqmm) ECC.[E-16/7(b) x 2 + E-9/1(d)]

Supply of230V 50HZ Single/Twin 4ft LED light fittings with 20 W Led tube incl. other accessories (NS)

Single (Philips cat no.TMC 501 P 1xT-LED 22W ) , 1 X MAS LED 18W T8 4ft, 2100lm (NS)

Twin(Philips cat no.TMC 501 P 2xT-LED 22W ) 2 X MAS LED 18W T8 4ft, 2100lm (NS)

Fixing only single/twin fluorescent light fitting suspended 25 cm bellow the ceiling with 2 No. 20 mm dia EI conduit (14 SWG) supports fixed with “L” type MS clamp whose one side fixed on ceiling with suitable size 4 nos. fastener and other side connected with the conduit with suitable size of bolts and nuts incl. S&F EI conduit, “L” type (125mmx125mm) 6mm thick and 25mm with MS clamps and connecting the length of PVC insulated wire and mending good damages to original finish and painting etc. by 3 core x 1.5sqmm. flexible round sheathed copper wire of 1.10 mt. length [C-2/17]

Extra. For suspension exceeding 25cm with S&F additional 2 nos 20mm dia. EI conduit(14SWG) supports&necy. 3 core PVC insulated sheathed copper wire and painting .[C-2/16]

Supply of 230V AC ceiling fans with down rod blades, canopy,fork,rubber bush etc(Orient Make New Breeze)

1200 mm(48’’) sweep [NS]

1400 mm(56’’) sweep [NS]

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire.[C-3/21(a)]

S & F of 9'' sweep, 1370 rpm AC exhaust fan incl. making hole on wall with nuts & bolts as required with louver shutter. (EPC heavy duty) 1370 r.p.m. and S& F louver with nuts and bolts or equivalent make of Orient Anchor. [C-4/28(a) + D-14/32(a)]

Supply and fixing 10W LED lamp (Make:Havells / Philips / syska ) [C-2/11]

Supplying & Fixing MS fan clam of two piece type for RC ceiling as per approved specification, fabricated from 40 mm x 9 mm MS flat including making good damages to building roof with satisfactory finishing and painting – (As per Drawing no. 475 of PWD Specification Book – May 1991).[D-14/29]

Supply & Fixing Socket type fan regulator (Step type) (Brand approved by EIC) on existing sheet metal switch board with bakelite/perspex top cover by screw after making housing for regulator knob by cutting bakelite/perspex top cover incl. making necy. connections etc.[E-6/18(a)]

Supply and fixing of 72W LED Street light luminaires complete with all accessories(to be fixed on Minipole-Top) , Make- Crompton, NEXUS NEO , LSTP-72-CDL-M on minipole with necy. Connection.[NS]

S&F 80 mm dia . GI pipe pole (Tata Make- Medium) of 1.5 mtrs long with sole plate on roof incl.CC (6:3:1) muffing 450x450 x600mm. in size or equivalent cylindrical muffing above roof level incl. 3mm.thick neat cemented finish and G.I. earth bolt, Cable entry after making holes on pole incl. S&F 200x150 x100mm. GI (4 mm thick) loop box in pole muffing and S&F single arm brackets assembly made of 100mm dia 0.3mtr long welding with 40 mm dia 1.5 mtr long steel pipe 3.64mm thick including painting with synthetic enamel paint as per GS. (H-1/3(a)(ii))

S&F 32 mm dia 3 mm thick polythene pipe from the base of the muffing to loop box at the time casting work of muffing as per GS. [E-2/1(d)]

Wiring in 2 x 1.5 sq. mm 1.1 KV grade ‘FR’ PVC insulated & unsheathed copper wire from loop box to SV fitting [E-9/1(a)]

Excavation of soil for installation of Earth Electrode and filling & ramming.[G-1/1]

For Morrum Soil @1.75cubic mtr/earth [G-1/1(b)]

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below:

By ISI-Medium GI pipe [G-1/2(a)]

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 40 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required. [G-2/4(b)

Connecting the equipments body to earth busbar including S & F 25 mm x 6 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc. [G-3/5(d)]

Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages

Solid GI Wire No. 4 SWG [G-2/5(a)(i)]

Finishing of the PVC insulated wire ends by socketing with pin/ring type copper sockets and insulated tapes etc. incl. supplying socket, tapes

2.5 sq. mm [F-5/9(i)]

4 sq. Mm [F-5/9(ii)

6 sq.mm [F-5/9(iii)]

10sq.mm[F-5/9(iv)]

RAHUL TRADERS

DEB SHANKAR LAYEK