WORKS SERVICES FOR IMPROVEMENT TO

Amount

Taking down chowkats or frame n exc 1.5 Sqm each (without taking off shutter from the fram) all as specified and as directed.

Taking down chowkats or frame exc 1.5 Sqm and n exc 4 Sqm each (without taking off shutter from the frame) all as specified and as directed.

Taking down shutter only of any description n exc 1Sqm all as specified and as directed.

Taking down shutter only of any description exc 1Sqm n. exc 2Sqm all as specified and as directed.

Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) rubbish off the premise.

Taking dawn cement plaster any description on brick or stone wall/ celling including raking out joint , hacking for key scrubbing with water etc.

Taking up or down steel tubing pipe and connections 15mm bore

Taking up or down steel tubing pipe and connections 20mm bore

Dismantling water tanks n exc 500ltr capacity.

Dismantling water tanks n exc 1000ltr capacity.

Demolition of wall of brick and stone wall built in cement mortar including all quoins, arches, pillars ,etc all as specified and as directed.

Demolition of stone slabs and tiles of any description, laid bedded and pointed in any mortar.

Demolition of Concrete any description and in any position not otherwise specifically provided for

Dismantling of CI drain pipes 75/100mm internal dia, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Excavating in post holes in soft/loose soil each n.exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm.

M&L ATT along the internal and external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in apron complete all as specified and as directed.

M&L ATT to soil under existing floors using emulsion @ one litre per hole,300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same

M & L PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in footings and foundation fillings.

M&L PCC 1:2:4 type B-0, using 12.5mm graded stone aggregate laid to slope 1:30 in padding for WPT over roof slab, filling of pressed steel door frame complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:2:4 type B 0, using 12.5mm graded stone aggregate in cover fillet of 75 mm radius at junction of roof slab and parapet wall etc complete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound.

M&L Brick work sub class B bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 all as specified and as directed by Engineer-in-Charge

M&L 30mm thick 2nd class hardwood glazed and skeleton shutter open rebated and prepared to receive glass gauze etc (without sash bar ) edges of framing plain chamfered or rounded filled with cut and mitred beads for securing, glass etc size of member of shutter as per specified in SSR Part-I section 8,clause 8.24 complete all as specified

M&L 2nd class hard wood 35mm thick Plain framed, panelled shutter(two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both face. The size of rail and style as per IS:1003(Part-I), klin seasoned and chemically pressed treated complete all as specified

M&L Factory made flush shutters 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides as in CB shutter as in shutter complete all as specified

M&L Factory made flush shutters 25mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides as in CB shutter as in shutter complete all as specified

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specifications complete all as specified

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with hea tmoulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, as per specification complete all as specified

S&F 200mm long aluminium anodized barrel tower bolts of extruded section and fixed.

S&F 150mm long aluminium anodized barrel tower bolts of extruded section and fixed

S&F 300mm aluminium alloy anodized sliding door bolt with haps and staple (bolt type) and fixing clip of sheet cast or extruded section or cast aluminium alloy and fixed complete all as specified

S&F 150mm long aluminium handle cast type anodized complete all as specified

S&F 150mm size hasp and staple, safety type aluminium anodized including bolt to hinge plate and fixed with screws complete all as specified

S&F Towel Rail 600mm long CP fixed with and including Chromium plated brass screws and wooden/plastic cleats.

S&F Door stopper of 150 mm long (ISI Marked) aluminum alloy body and tongue double legged anodized with hard draw steel spring overall length of cover plate fixed in floor complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia wire and average width of aperture 1.14mm and fixed with powder coated aluminium beading/wood beading complete all as specified.

M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified

M&L Mild steel screw bolts (machine made) with hexagonal or squareheads of min 12mm neck at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long in chain link fencing complete all as specified.

M&L Mild steel, plain, black sheet 1.00 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required all as directed

M & L Joist, channel, angle, Flat or tee sections, fixed independently, withoutconnecting plates as in fencing post etc. Fe 410 -W (Gde-E- 250) complete all as specified

M&L Framed work ( Fe 290 gde E 165) as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed

Supply only Chain link MS galvanisd fencing, any size or type

Fixing only chain link fencing including line wires, any mesh, size and type to any typeof standards, rails, straining bolts, etc. Including provision of binding wire complete all as specified and as directed

S & F MS round bar 10 mm dia as in line wire to chain link fencing and similar articles conforming to FE -290 Gde-165 cut to length bend to shape as required complete all as specified and as directed.

M&L Pressed steel frames(105 X 60) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.complete all as specified and as directed.

M&L Pressed steel frames(125 X 60) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.complete all as specified and as directed.

Removing of existing unserviceable water proofing treatment taking down cement plaster etc, of any description and cleaning of top surface of cement concrete flushing out junction of parapet walls & washing down with water to remove all dirt etc including preparation of surfaces to receive new treatment and removing the rubbish off premises.

M&L Applying cold bituminous primer @ 0.30 Ltr / Sqm conforming to IS 3384 laying APP polymer modified membrane 3mm thick 3 Kg/Sqm in weight with non-woven polyester reinforcement with plain finish and sealing all overlaps of 75mm in length side and 75mm on width side of membrane by torching the same as per manufacture instruction and all as per specified particular specification including application of solar reflective aluminium paint all as specified and directed by Engr-in Charge MAKE:-STP/PIDILITE/TIKITAR Note:-(a) Rate quoted deemed to be inclusive of cleaning of surface to be treated properly to receive the primer and all as directed by the Engr-in-Charge. © Necessary guarantee certificate shall be given for the material for 10 years from the date of completion of work. (e) APP membrane treatment shall be done firstly at corners and junction of parapet wall 30cm on vertical position and 30cm on horizontal position shall be done with proper attention and work carried out by authorised applicator only. Main portion of roof treatment shall be commenced only on completion of corners/edges/junctions. (f) APP membrane shall be taken upto outside of the parapet wall to an extent of 150mm minimum. (g) Ensure while laying the treatment no bulging on surface/voids shall be found and proper care/attention be given for the treatment. (h) If any work executed at site without any authorised applicator, the same shall be rejected and no payment shall be consider. (j) Contractor shall produce the certificate from the manufacture for the authorised applicator before commencement of work.

M & L 75mm thick PCC 1:3:6 type C- 2 using 40mm graded aggregate as in plinth protection finished even and smooth without using extra cement.

M&L Coloured ceramic tiles 8-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 SQM, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match premium quality as in floor etc complete all as specified

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 SQM, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match premium quality as in floor etc complete all as specified.

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 SQM on vertical surfaces/skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match premium quality as in floor etc complete all as specified.

M&L Coloured ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 SQM, in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match premium quality as in floor etc complete all as specified.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 SQM but not exceeding 0.11 SQM, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L Glazed ceramic coloured tiles in vertical surfaces 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L 15mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes all as specified and directed complete all as specified.

M&L10mm thick screed bed in CM 1:4 mixed with WPT 3% by weight of cement all as specified and as directed by Engr-in-Charge.

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 to receive tiles etc on vertical surfaces of walls all as specified and directed.

M&L 20mm thick granite slab with fully rounded edges on front face fixed with adhesive or laid in neat cement slurry over and incl 15mm thick screed bed in CM 1:6 including cutting space for sink & gas pipe hole complete all as specified and directed in Engineer -in -Charge.

M&L Machine cut Pre polished Kota stone slab flooring 20-25mm thick over and including 15mm thick cement screed base in CM 1:3 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab in single piece as in window cill, staircase etc complete all as specified and directed in Engineer -in -Charge..

M & L 10 mm thick rendering in CM 1:6 on concrete surfaces / fair faces of brick masonry wall, finished even and smooth with thin layer of sagol complete all as specified.

M & L 15 mm thick rendering in two layer 10mm thick backing coat in CM 1:6 and finishing coat 5mm in CM 1:4 using water proofing compound on faces of brick masonry wall, finished even and smooth without using extra cement.

M&L Rendering 5mm thick on concrete surface of ceiling CM 1:3 finishing the surface fair and even complete all as specified and directed.

M&L Preparation of old surfaces and apply 3mm thick wall care putty on wall/ceiling finished all as approved by Engr-in-Charge.

M&L Preparation of new plastered Surface of wall and application of two coats of Exterior Emulsion Paint over one Coat Primer

M&L Preparation of new surfaces of wall rubbing down and applying two coat of oil bound distemper over application of chalk whitening all as specified (any tint shade as approved by GE) as directed by Engineer -in-Charge.

M&L Preparation of new plaster wall surface and applying three coats of white wash on ceiling surface complete all as specified and directed

M&L Complete removal of existing treatment and apply two coats of Exterior acrylic Emulsion over a coat of primer complete all as specified and directed

M&L Preparation of old decorated surfaces and applying one coat of Exterior acrylic Emulsion over a coat of primer complete all as specified and directed

M&L Complete removal of existing treatment and applying two coat of oil bound distemper over application of chalk whitening complete all as specified (any tint shade as approved by GE) as directed by Engineer -in-Charge.

M&L Preparation of old decorated surfaces and applying One coat of oil bound distemper over application of chalk whitening complete all as specified (any tint shade as approved by GE) as directed by Engineer -in-Charge.

M&L Complete removal of existing treatment and applying three coat of white wash on wall complete all as specified as directed by Engineer -in-Charge.

M&L Complete removal of existing treatment and applying three coat of white wash on ceiling complete all as specified as directed by Engineer -in-Charge

S&F 4mm thick Sheet glass, ordinary quality and glazing with glazing clip and powder coated aluminium beading in square n exc 0.5 sq. m in each pane

M&L Preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer.

M&L Preparation and Painting new Steel Surfaces with 2 coat Synthetic Enamel Paint of any description, over 10cm in width or girth, not otherwise described over Red Oxide Primer

S&F 15mm dia tubes ‘Medium grade’ galvanized with all fittings and fixed complete to walls and ceiling or laid in floors,

Fixing only 15mm dia GI tubing with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified

S&F 20mm dia tubes ‘Medium grade’ galvanized with all fittings and fixed complete to walls and ceiling or laid in floors,

Fixing only 20mm dia GI tubing with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts as in repairs screwed for iron pipe and fixed to 15mm bore pipe all as specified.

S&F Bib taps, cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts as in repairs screwed for iron pipe and fixed to 15mm bore pipe all as specified.

S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed to15mm bore pipe complete all as specified

S&F 500 Ltr rotational moulded polyethylene water storage tank three layered (cylindrical vertical with closed top) hoisted all as specified.

S&F 1000 Ltr rotational moulded polyethylene water storage tank three layered (cylindrical vertical with closed top) hoisted all as specified.

S&F 20 mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified.

S & F Vitreous china wash hand basin, flat back, size 450x300mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete as in repairs all as specified

S&F Vitreous China squatting pan, Orissa pattern of size 580x440mm, white with integral foot rest including connection to trap & flushing pipe complete as in repairs all as specified.

S&F Vitreous china pedestal pattern white (excluding fixing both flushing cistern and flush pipe) complete as in repairs all as specified

S&F Plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated hinged device complete as in repairs all as specified

S&F 10 litres capacity PVC valve less symphonic action type, flushing cistern, low level, white, with inlet, ball valve float handle including brackets complete as in repairs all as specified

S&F 32mm brass chromium plated waste coupling for wash hand basin complete all as specified

S&F 32mm PVC waste pipe for wash hand basin., 600mm long complete as in repairs all as specified

S&F PVC connection 15mm size with PTMT nuts of length 60cm complete all as specified

S & F Soap dish, any type, fixed to plugs with chromium plated brass screws complete as in repairs all as specified.

S&F CI soil waste vent and rain water pipe 75 mm bore (ISI Marked) in any length with or without ears with cement joint laid in floor/fixed to wall complete all as specified and directed.

S&F CI soil waste vent and rain water pipe 100 mm bore (ISI Marked) in any length with or without ears with cement joint laid in floor/fixed to wall complete all as specified and directed.

S&F Cast iron floor trap 75 mm outlet dia with grating including jointing to waste pipe fixed in cement concrete type B1, (1:2:4) complete as in repair all as specified and directed.

S&F 100mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F 75mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed..

S&F 100mm bore bend (any radius) with duck foot or heel rest complete all as specified and directed..

S&F 75mm bore bend (any radius) with duck foot or heel rest complete all as specified and directed..

S&F Chromium plated shower roses of 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete as in repair all as specified and directed.

S&F Sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

M&L Treatment to sunken portion (including necessary dismantling of tiles and PCC along with PCC 1:2:4 of req thickness) with 10mm thck plaster in CM 1:4 with WPC Liquid complast 421 and applying one coat each of Nitroproof 100 and Nitroproof 120 on plastered surface. Rendering again 10 thick plaster in CM 1:4 mixed with complas 421 in sunken portion of WC and CI pipe joint shall be filled in filling of lean concrete PCC 1:5:10 typeE2 complete all as specified and directed.

S&F SS plate rack 1mm thick of Size 31"x36"x10" fixed with screws complete all as specified Make Swasti Nirali Code No 1049 or equivalent make as approved by GE in writing .

M & L Filling surface cracks not esxc 5 to 7 mm wide with Dr fixit complete all as specified and directed.

S&F 75mm long SS butt hinges and fixed to frame with screwed or welding complete..

S&F Powder coated aluminium work for door, windows and ventilators and partition wall with one or more rebates fixed in position as per manufacturer's instruction including necessary joining cleat, glazing clips, rubber packing, beading ,plaster work on edges during fixing (if required)etc complete all as specified and directed.

S&F 25 mm dia curtain drapery rod decorative type cut to length and fixed complete all as specified and directed.

S&F Bracket suitable for 25mm dia curtain rod with steel screw/ wooden screw complete all as specified and directed.

Taking down carefully point wiring including (light, fan, socket or power complete fittings, such as switches, ceiling roses, pendant holders, Batten holders, shades conical fan regulators, light or power sockets etc) removing materials from site and making good disturbed surfaces of walls roofs etc all as directed.

M&L Point wiring complete as specified with 1100 volt grade 1.5sq.mm. (nominal area) single core PVC insulated unsheathed cable FRLS multi-stranded copper conductor drawn through and including rigid non-metallic PVC concealed conduit of suitable size but not less than 20mm dia, with all fittings, concealed in wall/roof /floor including decorative modular cover plates (inner and outer) suitable for housing modular pattern switches/ sockets/ regulators etc. along with necessary metal boxes flush mounting in the wall duly earthed with same cable as for wiring above but green in colour as continuous earthing wire complete all as specified for :-

(a)One light point controlled by one one/way switch.

(b)One Fan/Ex fan point controlled by one one/way switch.

(c) One 3 pin 5 Amps socket outlet on same board with other switch.

(d) One 3 pin 5 Amps socket outlet on independent board with other switch.

(e)One bell point controlled by one one/way switch.

(f)One light point controlled by one two/way switch.

All as above item No115 but wiring with 2.5 sqmm multistranded copper conductor unsheathed and 2.5 sqmm copper conductor unsheathed cable FRLS as earth continuity conductor for one 5 pin 15 Amps power socket outlet point on independent board/400 watt flood light.

M&L Sub main wiring using two run single core 6 Sqmm fire retardant PVC insulated and unsheathed cable FRLS with copper conductor 1100 vots grade, ISI marked complete with PVC conduit accessories like bends tees etc and PVC insulated copper cable 6 Sqmm for earth ire and connecting to earth dolly complete all as specified and directed. ,

M&L Sub main wiring using two run single core 4 Sqmm fire retardant PVC insulated and unsheathed cable FRLS with copper conductor 1100 vots grade, ISI marked complete with PVC conduit accessories like bends tees etc and PVC insulated copper cable 4 Sqmm for earth ire and connecting to earth dolly , complete all as specified and directed.

S&F Modular switch 1 way 6A, 1 module complete all as specified and directed.

S&F Modular switch 1 way 16A, 1 module complete all as specified and directed.

S&F Modular Bell push 6A 1 module complete all as specified and directed.

S&F Modular switch 2 way 6A,1 module complete all as specified and directed.

S&F Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F Ceiling rose surface Bakelite three terminal 65 x 50 mm three terminal 250/230 volts ISI marked complete all as specified and directed.

S&F Fan step regulator, 120W - 2 module complete all as specified and directed..

S&F DB’s Sheet metal enclosure for SPN DB 12 way type 240 volts and 200 Amp ratings bus bar complete all as specified and directed.

S&F DB’s Sheet metal enclosure for SPN DB 8 way type 240 volts and 200 Amp ratings bus bar complete all as specified and directed.

S&F Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

(a). MCB SP up to 32 Amp, 240 volts

(b). MCB SPN upto 63 Amp, 240 volts

S&F Exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m ISI marked complete all as specified and directed

S&F LED Tube light fitting ENERGY Efficient 20 Watt 2000 lumen bright light complete all as directed by Engr-in-charge

S&F LED Tube light fitting ENERGY Efficient 10 Watt 2000 lumen bright light complete all as directed by Engr-in-charge

S&F Wall mounted light fitting suitable for retrofit LED lamp upto 14 watt B22 with lamp champagne gold finish fixture with plastic body, Opal white PC diffuser for glare free light complete all as directed by Engr-in-charge.

S&F LED security light luminaire 35 Watt freedom , pressure die cast aluminum housing, heat resistant glass, IP65 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light complete all as specified and directed.

S&F Bracket for security light made up of 25 mm dia, 1.0 mtr long GI pipe, light grade, bent to required length, fixed to wall with 2 clamps made off 20x3 mm mild steel flat minimum 15 cm long, 4 Nos 8 mm dia bolts with nut complete including taking down old unserviceable all as specified and directed by Engr in Charge.

Labour only making hole for Exhaust fan and making good the disturbed surface with existing colour complete all as specified and directed.

S&F Buzzer ding dong type AC 230 Volt all as specified and directed

S&F Industrial metal clad plug in socket and plug top with 20Amp SP MCB complete all as specified

S&F PVC blanking plate complete all as specified directed.

M&L TV socket with modular plate for TV connection complete all as specified directed.

Supply, install, testing and commissioning meter box cubicle suitable for 6 Nos smart electric meter in separate compartment each of 410mm x 310mm x 250mm, intercom apartment working space, made out of 2 mm thick CRCA sheet duly powder coated, including 200 Amps rating 4 Nos copper bus bar chamber, including power wiring with using PVC insulated stranded FRLS copper wire of size 10 sqmm, earthing fixing arrangements, duly provided lugs from bus bar to meter and meter to control MCB with provisioning transparent glass in front of meter complete rubber gasket and locking and sealing arrangement including following MCCB/MCB (a). Incomer MCCB 4 pole 160 Amps 25 KA - 01 Nos (b). Outgoing MCB SPN 63 Amps - 06 Nos (c). Outgoing MCB SPN 20 Amps - 01 Nos (d). Indicating Lamp RYB - 1 Set (e). Smart single phase electric meter four wire energy meter BIS 16444(reaffirmed 2020) having current capacity 16-60 Amp, 240 volt accuracy class 1.0 - 6 Nos

Supply, install, testing and commissioning meter box cubicle suitable for 4 Nos smart electric meter in separate compartment each of 410mm x 310mm x 250mm, intercom apartment t working space, made out of 2 mm thick CRCA sheet duly powder coated, including 200 Amps rating 4 nos copper bus bar chamber, including power wiring with using PVC insulated stranded FRLS copper wire of size 10 sqmm, earthing fixing arrangements, duly provided lugs from bus bar to meter and meter to control MCB with provisioning transparent glass in front of meter complete rubber gasket and locking and sealing arrangement including following MCCB/MCB (a). Incomer MCCB 4 pole 160 Amps 16 KA - 01 Nos (b). Outgoing MCB SPN 63 Amps - 08 Nos (c). Outgoing MCB SPN 20 Amps - 01 Nos (d). Indicating Lamp RYB - 1 Set (e). Smart single phase electric meter four wire energy meter BIS 16444(reaffirmed 2020) having current capacity 16-60 Amp, 240 volt accuracy class 1.0 - 4 Nos

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one 20 A single pole MCB complete all as specified and directed.

S&F Wall mounted fan 300 mm sweep, 230 V, with complete along with removal of old unserviceable fan complete all as specified and directed .

M&L Earthing complete as per electrical plate NO.3 of MES SSR Part I with galvanised steel plate earth electrode 600 mm x 600mm x 6 mm buried directly in ground in a pit of depth not less than 2.25 metre below ground level with the top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to and incl galvanised iron or steel earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel earthing wire protected by galvanised iron or steel pipe 15 mm dia light grade and connected to main switch board or main control board watering pipe shall be 20 mm dia GI medium grade including excavation and earth work in any type of soil, PCC pit, CI Frame, RCC covers complete.as specified and directed by Engr-in charge.

ALBA AC AND REF SERVICES

DMA PROJECTS

SNEH TRADERS