Laying of underground cable network with terminations in the area of DGVCL under all scheme for Rander T-1 Sub division under Rander Division and if required work to be carried out at other sub division under Rander Division

Schedule-B for ARC for Erection and labour work of supply, laying, testing & commissioning of 11/22 KV Underground XLPE cable (XLPE cable will be

supplied by DGVCL) with cable end termination & straight through jointing kit (To be supplied by contractor) on ARC basis under All Scheme for

Rander T-1 sub division under Rander division and if required work to be carried out at other sub division under Rander Division.

Sr. No. Item Code Description Unit FY 2024-25

Labour charge for excavation of cable trench of 400mm width x 1200mm depth, in any

1 9925000001 type of soil for laying of cable of size up to 240 mm2 (For additional cable 200 mm Meter

additional width shall be considered i.e. half trench length is to be considered)

Labour charge for excavation of cable trench of 600mm width x 1200mm depth, in any

2 9925000002 type of soil for laying of cable of size up to 240 mm2 (For additional cable 200 mm Meter

additional width shall be considered i.e. half trench length is to be considered)

Labour charge for excavation of cable trench of 400mm width x 1500mm depth, in any

3 9925000003 type of soil for laying of cable of size up to 240 mm2 (For additional cable 200 mm Meter

additional width shall be considered i.e. half trench length is to be considered)

Labour charge for laying of 11kV / 22 kV XLPE Cable of size up to 240 mm2 & preparation

of sand layer 100mm thick, in the cable trench & covering the cable with 150 mm dia

(Inner), thickness 25 mm, 1.0 meter long RCC half round muffs and providing and fixing

4 9925000004 of 4inch width yellow colour polyethylene tape with printing "CAUTION ELECTRIC CABLE Meter

BELOW" at 0.75 m depth from ground surface after laying cable in trench. This will

provide indication that electric cable is passing underground so as to protect cable from

mechnical injuries, refilling the same, as per Instruction of Engineer in Charge (EIC).

Labour charge for horizontal drilling using Auger machine without damage to surface

road at max 2.0 mtrs depth & putting of 6.11 kg/cm2 , class-4,Green color, 110mm O.D.

8.5mm thickness H.D.P.E. pipe confirms to IS 4984-1987(3rd revision) and BIS certification

5 9925000005 and laying of 11KV/22KV XLPE cable of size up to 240 mm2 in HDPE pipe, as per Site Meter

Condition (excluding cost of pipe). The detail map obtained from HDD machine and excell

sheet(hard and soft copy) indicating the respective depth and distance from adjacent

landmark for each segment for HDD is must required to be submitted. HDD to be carried

out at depth 1.5 mtrs to 2.0 mtrs as per site conditions and as per instruction of EIC.

Labour charge for horizontal drilling manually without damage to surface road at max

mtrs depth & putting of 6.11 kg/cm2 , class-4,Green color, 110mm O.D. , 8.5mm thickness

H.D.P.E. pipe confirms to IS 4984-1987(3rd revision) and BIS certification and laying of

6 9925000006 11KV/22KV XLPE cable of size up to 240 mm2 size, as per Site Condition (excluding cost of Meter

pipe). The detail map and excell sheet(hard and soft copy) indicating the respective depth

and distance from adjacent landmark for each segment of cable to be submitted. Drilling

to be carried out at depth Minimum 1.2 mtrs to 2.0 mtrs as per site conditions as per

instruction of EIC.

Supply of 6.11kg/cm2 , class-4,Green color, 110mm O.D. , 8.5 mm thickness H.D.P.E. pipe

7 9925000007 confirms to IS 4984 and BIS certification for laying of underground 11KV / 22KV XLPE cable Meter

up to 240 mm2 size.

Labour work for RCC concreting on disputed location and repairing of damage portion of

8 9925000008 road crossing for the work carried out for roads crossing as well as concreting & muffing CMT

of ploes including all materials (1:2:4)

Sr. No. Item Code Description Unit FY 2024-25

Providing & fixing concrete stone route marker of 300 mm width x 150 mm thick x

mm height embedded in earth at least 300 mm below & 350 mm above ground level

respectively at distance approx 50 meters along the length of cable. The RCC concreting

(1:2:4)(all necessary maeterials will be in bidder's scope) of route marker is to be carried

out 300 mm width x 150 mm thick x 300 mm below ground level as per instruction of

9 9925000009 EIC. The route marker should be with name of company with approved yellow colour- No.

DGVCL. The distance from marker to cable and cable depth with feeder name etc.,

marked with arrow sign is to be painted on it.The route marker is to be fixed at location

near to any fixed permanent location (not necessary to fix exact on top of cable) as per

instruction of EIC.

Erection of D.P. (double pole) structure using 9 / 11 Mtr. RSJ pole with cable connection

arrangement along with fitting of necessary fabrication for 11KV cable including

10 9925000010 excavation of pit & refilling of earth as per instruction of EIC. (Exclusive of concreting & No.

muffing of poles)

Erection of Single pole structure using 9 / 11 Mtr RSJ pole with cable connection

arrangement along with fitting ofnecessary fabrication for 11KV/22 KV cable including

11 9925000011 excavation of pit & refilling of earth as per instruction of EIC. (Exclusive of concreting & No.

muffing of poles)

Erection of D.P. (double pole) structure using 8.0 Mtr. PSC pole with cable connection

12 9925000012 arrangement along with fitting of necessary fabrication for 11KV cable including No.

excavation of pit & refilling of earth as per instruction of EIC. (Exclusive of concreting &

muffing of poles)

Erection of Single pole structure using 8.0 Mtr PSC pole with cable connection

arrangement along with fitting ofnecessary fabrication for 11KV/22 KV cable including

13 9925000013 excavation of pit & refilling of earth as per instruction of EIC. (Exclusive of concreting & No.

muffing of poles)

Labour charge for erecting of 11kV / 22 kV XLPE cable of size up to 240 mm2 on DP

14 9925000014 Structure with fixing of 02 Nos polymer cleats on top and middle part.Polymer cleats, Per Job

nut bolts etc. fixing material to be provided by contractor.

Providing & fixing of 6.11kg/cm2 , class-4,Green color, 110mm O.D. , 8.5mm thickness

H.D.P.E. pipe confirms to IS 4984 and BIS certification on the erected DP structure for

the mechanical protection of cable by inserting the cable inside HDPE pipe. The HDPE pipe

15 9925000015 shall be erected in such a way that 300mm shall be below the ground level and the rest Per Job

2700 mm shall be supported on the DP Structure with 01 No Polymer cleat.All

materials including polymer cleat and Nut bolt to be provided by contractor.

Providing and fixing of pipe type earthing from 80 mm dia class-B GI pipe with pit to be

16 9925000016 filled with salt & coke and construction of chamber as per DGVCL Drg. No. dg /100 for DP No.

and cable. The earthing pit should be joined with cable by G.I. strip of size 1” width &

mm thick. All material GI pipe, Coke, Salt etc will be supplied by bidder.

Supply & fixing of heat shrink type end terminations (outdoor) for upto 11kV 3C x

mm2 size XLPE cable as per DGVCL technical specification

Supply & fixing of heat & shrinkable end terminations (outdoor) for upto 22 kV 3C x

mm2 size XLPE cable as per DGVCL technical specification)

19 9925000019 Supply & fixing of heat shrink type end terminations (indoor) for upto 11kV 3C x 185 mm2 No.

size XLPE cable as per DGVCL technical specification)

Supply & fixing of heat & shrinkable end terminations (indoor) for upto 22 kV 3C x

mm2 size XLPE cable as per DGVCL technical specification

21 9925000021 Supply & fixing of heat shrinkable straight through joint for upto 11kV 3C x 185 mm2 size No.

XLPE cableas per DGVCL technical specification.

22 9925000022 Supply & fixing of heat shrinkable straight through joint type for upto 22kV 3C x 185 mm2 No.

size XLPE cable as per DGVCL technical specification

Labour charge for excavation of 2100mm long x 1200mm wide x 1200 mm deep joint pits

23 9925000023 for installation of 11kV / 22kV Straight through joints as per instruction of engineer-in- No.

charge & covering the cable with 150 mm dia (Outer), thickness 25 mm, 1.0 meter long

RCC half round muffs & refilling same as per instruction of EIC .

Providing and fixing of insulating bus bar, made from 11KV/22KV XLPE cable after removal

of semi conducting layer and applying of PVC heat shrinkable anti-tracking core insulating

tubing (1.1KV), on both end terminal using Aluminium long barrel heavy duty up to 240 sq

24 9925000024 mm lugs, Aluminium bus connector. Taping with PG- clamp for bus conductor as per No.

drawing and as per instruction of EIC. The Alluminium lugs and PG clamp shall be covered

with 11KV/22KV HT insulating tapes.(11KV/22KV XLPE cable will be in scope of DGVCL

while all other materials will be in bidder's scope)

Sr. No. Item Code Description Unit FY 2024-25

25 9925000025 Testing of cable at various points and commissioning the feeder as per instruction of No.

engineer-in-charge.Test result shall be submitted by contractor with bill.

Preparation and submission of 6 (six) copies, of complete layout drawings with GIS

26 9925000026 mapping as per actual cable routing showing road crossing, HDPE pipe sleeving, jointing Set

locations, markers etc.

Providing and fixing of Sign Board at junction point Made out of 2 mm aluminium sheet

size 750x300 mm (2.5 x 1ft) rectangle, as per design, pre treated with phosphate process

and acid etching coated with one coat of epoxy primer and two coats of best quality

paints, refloctrorised with Hi-Intensity retro – reflective sheeting as per the latest and

27 9925000027 frame fabricated from suitable size iron angle. The Sign Board is to be fixed on the base No.

prepared from channel and bracing angles which is grouted by means of cement

concreting of 1:2:4 for size of 300 mm dia x 800 mm height (500 mm to be grouted in

ground). The details to be displayed on sign board will be given by In-charge Engineer.

(a) Hi intensity Micro prismatic Grade

Providing and fixing of Sign Board (Danger Board) on Distribution Transformer Centers

Made out of 2mm aluminium sheet size 300x300mm (1x1ft) as per design, pre treated

with phosphate process and acid etching coated with one coat of epoxy primer and two

28 9925000028 coats of best quality paints, refloctrorised with Hi-Intensity retro-reflective sheeting as per No.

the latest and frame fabricated from suitable size iron angle. The Sign Board (Danger

Board is to be fixed at the location as per instruction of In-charge Engineer.

(a) Hi intensity Micro prismatic Grade

Providing & fixing of aluminium tag of size 250 mm (L) x 75 mm (W) from 3 mm aluminium

sheet along with 1.0 mm dia aluminium binding wire for fixing of aluminium tag near end

29 9925000029 termination joint at DP structure for identifyng the cable. The details of feeder i.e. 11 / 22 No.

KV with feeder name shound be punched on the tag by letter punch of size 16 mm as per

instruction of In-charge Engineer.

30 9925000030 Supply & fixing of heat shrink type end terminations (outdoor) for 11kV 3C x 240 mm2 No.

size XLPE cable as per DGVCL technical specification

31 9925000031 Supply & fixing of heat & shrinkable end terminations (outdoor) for 22 kV 3C x 240 mm2 No.

size XLPE cable as per DGVCL technical specification)

Supply & fixing of heat shrink type end terminations (indoor) for 11kV 3C x 240 mm2 size

32 9925000032 XLPE cable as per DGVCL technical specification) No.

33 9925000033 Supply & fixing of heat & shrinkable end terminations (indoor) for 22 kV 3C x 240 mm2 No.

size XLPE cable as per DGVCL technical specification

34 9925000034 Supply & fixing of heat shrinkable straight through joint for 11kV 3C x 240 mm2 size XLPE No.

cableas per DGVCL technical specification.

35 9925000035 Supply & fixing of heat shrinkable straight through joint type for 22kV 3C x 240 mm2 size No.

XLPE cable as per DGVCL technical specification

Installation, Testing and commissioning of 11 KV,630 A SCADA Compatible, RRL type-

36 9925000038 Way RMU including Two numbers of earthings as per Drawing (material is in bidder's No.

scope) and as per DGVCL Technical specification.

Installation, Testing and commissioning of 11 KV,630 A SCADA Compatible, RRLL type-

37 9925000039 Way RMU including Two numbers of earthings as per Drawing (material is in bidder's No.

scope) and as per DGVCL Technical specification.

Installation, Testing and commissioning of 22KV,630 A SCADA Compatible, RRL type-3

38 9925000040 Way, RMU including Two numbers of earthings as per Drawing (material is in bidder's No.

scope) and as per DGVCL Technical specification.

Installation, Testing and commissioning of 22KV,630 A SCADA Compatible, RRLL type-4

39 9925000041 Way, RMU including Two numbers of earthings as per Drawing (material is in bidder's No.

scope) and as per DGVCL Technical specification.

Construction of plinth for 11KV, RRL type- 3 Way (i.e Two numbers of Isolator & One

40 9925000042 number of Breaker) Ring Main Unit as per DGVCL's technical specification mentioned in No.

drawing no: Drg. 11kv-01. All required material will be supplied by contractor.

Construction of plinth for 11KV, RRLL type- 4 Way (i.e Two numbers of Isolator & Two

41 9925000043 number of Breaker)Ring Main Unit as per DGVCL's technical specification mentioned in No.

drawing no:Drg. 11kv-02.All required material will be supplied by contractor.

Sr. No. Item Code Description Unit FY 2024-25

Construction of plinth for 22KV, RRL type- 3 Way (i.e Two numbers of Isolator & One

42 9925000044 number of Breaker) Ring Main Unit as per DGVCL's technical specification mentioned in No.

drawing no: Drg. 22kv-01. All required material will be supplied by contractor.

Construction of plinth for 22KV, RRLL type- 4 Way (i.e Two numbers of Isolator & Two

43 9925000045 number of Breaker)Ring Main Unit as per DGVCL's technical specification mentioned in No.

drawing no:Drg. 22kv-02.All required material will be supplied by contractor.

Modifications e.g.Providing and fixing of Terminal protectors i.e. Re-use able boot (HT

Side 11/22KV, LT Side 1.1KV) including 11/22 KV insulating taps and L.T.(1.1 KV) insulating

taps ,Busbar, Tapping from Bus Bar (11/22 KV XLPE cable) through P.G. Clamp for H.T.

Jumper to D.O. Fuse to bushings of Transformer Center, providing & Fixing of jumper

and providing & fixing of Heat Shrinkable Anti Tracking Core Insulating Tubing (Insulation

Level 11/22 KV) in H.T. jumper , Clamping arrangement of cable support frame on both

side of existing Over Head type Distribution Transformer to utilize in Under Ground cable

network as per drawing & as per instruction of Engineer incharge. All live parts i.e. PG-

Clamp, connections of D.O.fuses, HT bushings etc . shall be covered with fixinng of 11/22

44 9925000046 KV HT insulating tapes. ( 11/22 KV XLPE cable will be in scope of DGVCL while all other No.

materials will be in bidder's scope ) .

45 9925000047 Laying of any size of 11/ 22 KV XLPE /PILC Cable in redaymade trench or in open space Per Mtr

46 9925000060 Labour charges for Lying of O/H XLPE cable pole to pole KM

47 9925000064 Supply of 150 mm dia (Inner), thickness 25 mm, 1.0 meter long RCC half round pipe No.

In Words :-- Thirty Lakh Rupees Only

Executive Engineer (O&M)

DGVCL,Rander Division