TDO Quarter

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Excavation for foundation upto 1.5 m depth including sorting out and

1 stacking of useful materials and disposing off the excavated stuff upto 50 130.78 Cum 125.86

Meter lead.(A) Loose or soft soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting

2 out and stacking of useful materials and disposing off the excavated stuff 26.50 Cum 138.05

upto 50 Meter lead.(A) Loose or soft soil

Filling available excavated earth (excluding rock) in trenches. plinth, sides

3 of foundations etc. in layers not exceeding 20 cm. in depth consolidating 105.10 Cum 137.47

each disposited layer by ramming and watering

Filling foundation and plinth with murrum or selected soil in layer of 20 cm

4 in thickness including ramming watering and consolidating etc. Complete. 36.20 Cum 304.60

Providing and laying controlled cement concrete M.150 for curing complete

Including cost of formwork and reinforcement for reinforced concrete work

in (A) Foundations, footings,Base of columns and Mass concrete

Providing and laying controlled cement concrete M-250 and curing

complete including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in foundation footings, Raft,

base of columns and mass concrete.

Providing and laying controlled cement concrete M-250 and curing

complete including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in Columns, pillars posts and

struts For Plinth

Providing and laying controlled cement concrete M-200 and curing

complete including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in Columns, pillars posts and

struts For Ground Floor

Providing and laying controlled cement concrete M-200 and curing

complete including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in Columns, pillars posts and

struts For First floor.

Providing and laying controlled cement concrete M-250 and curing

10 complete including the cost of form work but excluding the cost of 12.40 Cum 6262.75

reinforcement for reinforced concrete work in Plinth BEAMS.

Providing and laying controlled cement concrete M-200 and curing

11 complete including the cost of form work but excluding the cost of 4.90 Cum 6416.71

reinforcement for reinforced concrete work in BEAMS Ground Floor.

Providing and laying controlled cement concrete M-200 and curing

complete including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in Lintels & Sill Ground Floor.

Providing and laying controlled cement concrete M-200 for reinforced

concrete CHHAJJAS not exceeding 10 cm. Thickness up to floor two level

including finishing the exposed surfaces with cement mortar 1:3 (1cement

:3 fine sand) to give a smooth surface centering and form work and curing

complete excluding cost of reinforcement. Ground Floor.

Providing and laying controlled cement concrete M-200 and curing

14 complete including the cost of form work but excluding the cost of 14.80 Cum 6487.78

reinforcement for reinforced concrete work in SLABS for Ground Floor.

Providing and laying controlled cement concrete M-200 and curing

complete including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in STAIRCASE for Ground

Providing and laying Controlled C.C. M-200 (C.C. 1:1.5:3 - 1 cement,

coarse snad, 3 graded stone agggregate of 20 mm nominal size) and curing

16 complete including the cost of formwork and excluding the cost of 8.70 Cum 7528.19

reinforcement for reinforced concrete work for horizontal and vertical

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

bending,binding and placing in position complete upto floor two level

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Brick work using common burnt clay building brick shaving crushing

18 strength not less than 35kg./Sq.Cm. in foundation and plinthin Cement 7.70 Cum 4279.98

Mortar 1:6. (1-Cement : 6- fine sand) (B) Conventional brick

Brick work using common burnt clay building brick shaving crushing

19 strength not less than 35kg./Sq.Cm. in foundation and plinthin Cement 24.30 Cum 4568.40

Mortar 1:6. (1-Cement : 6- fine sand) (B) Conventional brick For GF

Half brick masonry in common brunt clay building bricks having crushing

20 strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 - 58.70 Sqm 696.50

coarse sand ) in foundation and plinth (B) Conventional

Providing and laying Mirror polished Telephone Black Granite slab 18 mm

(Average) thick as per design incl. Half Round moulded both edges laid on

10 mm thick cement mortar 1:3 (1 -cement : 6 coarse sand) jointed with

grey cement slurry including rubbing and polishing and G.I. fastenings for

top horizontal as directed etc. complete. For Doors / WIndows cill & Jams

Providing 20 mm thick double coat mala cement plaster on interior brick /

concrete work for plastering comprising of base coat of 12 mm thick

cement plaster in cement mortar (1 Cement : 4 coarse sand) in rough

finishing and 8 mm thick top coat of cement mortar 1:2 (1 Cement :

Coarse sand) finished with trovel including scaffolding curing etc. complete.

Providing 15mm thick cement plaster in single coat on Mala side of single

23 or half brick walls for interior plastering upto floor two level and finished 358.40 Sqm 200.08

even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

20 mm. thick Sand Faced Cement Plaster on walls upto height 10 metres

above ground level consisting of 12 mm. thick backing coat of C.M. 1:3 (1

Cement : 3 Sand) and 8 mm. thick finishing coat of C.M. 1:1 (1 Cement :

Sand) etc. complete.

25 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 33.00 Rmt 382.65

Providing and fixing chicken mesh jali with square of 12.50 x 12.50 mm of

25 gauge at junction the stone. masonary and reinforcement cement

concrete member including fixing materials scaffolding labour etc.

Providing and laying 60 X 60 Double charged vitrified tile flooring over

mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new

surface or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry

27 including finised with flush pointing & cleaning the surface etc. complete for 62.90 Sqm 1566.51

light shade and 10 % Dark shade and including Dedo(10mm thick cement

plaster 1:3 (1 Cement : 3 Coarse Sand) and jointed with White Cement

slurry. ) for pattern in flooring as instructed by Engineer in charge (upto

Providing and laying 40cm x 40cm Antiskid Heavy Duty Parking tiles

mm thick tile flooring over 20 mm (average) base of cement mortar 1:6 (

cement: 6 coarse sand) on new surface or fixing on existing flooring by

adhesive material including jointed with Epoxy Grouting including finised

with flush pointing & cleaning the surface etc complete.

Providing and laying Machine Cut, Free Edges, Mirror polished GRANITE

stone slab in single piece, 18 mm (Average) thick for steps and riser as per

design incl. Half round front edge & 1 cm nosing in trade of steps laid on

29 mm thick cement mortar 1:6 (1 cement : 6 coarse sand ) on treads & 10 23.80 Sqm 2644.38

mm thick Cement mortar 1:3 for risers, jointed with grey cement slurry

including rubbing and polishing etc. complete.

Providing and laying Ceramic tiles 8mm thick in flooring treads of steps and

landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse

sand ) finishing with flush pointing in white cement including Dedo.

Providing and laying coloured glazed tiles of the size 300 mm x 600mm in

31 skirting, risers of steps and dedo on 10 mm. thick cement plaster 1:3 (1 56.40 Sqm 1523.67

cement : 3 coarse sand) & jointed with white cement slurry.

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Providing and laying polished Blue Kota stone (60mm X 30mm) slab

flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement :

6- coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and

jointed with grey cement slurry mixed with pigment to match the shade of

slab including rubbing and polishing etc. complete. (A) 25mm thick

Providing and laying 60 X 60 Matt Porcelain tile flooring over 20 mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new

surface or fixing on existing flooring by adhesive material including

33 dismentaling of existing flooring and jointed with 3mm Grove & Epoxy 6.00 Sqm 1530.15

Grouting including finised with flush pointing & cleaning the surface etc.

for pattern in flooring as instructed by Engineer in charge (upto 10 ton)

Providing and laying 60 X 60 Matt Finish GVT Tiles tile flooring over 20 mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new

surface or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the surface etc. including

Dedo For (10mm thick cement plaster 1:3 (1 Cement : 3 Coarse Sand) and

jointed with White Cement slurry. ) for pattern in flooring as instructed by

Engineer in charge (upto 10 ton)

Constructing Sandwitch Platform of 18 mm thick Polished Black Granite at

top and 30 mm thick Kota stone slab flooring fitting at bottom with

cementing Materials / adhsives including macking necessary grooves in

walls with Vertical Kotastone 30 mm x 2 No sandwitch thick every 60 cm

centre to cenre including all labour material of approved quality incl. full

moulded round front edge fixed in wall for partition and jointed with grey

cement slurry including rubbing and polishing etc. complete .

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe (

SCH-40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two

metre C/C or shall be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe (

SCH-40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two

metre C/C or shall be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level 50 mm dia. U.P.V.C. Pipe (

SCH-40) for cold water including fittings as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of clamp at every two

metre C/C or shall be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing and fixing concealed center point to wall ceiling & floor CPVC

(SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for

39 potable water of following dia. nominal bore tube fittings and clamps 20.00 Rmt 170.36

including making good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC

(SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for

40 potable water of following dia. nominal bore tube fittings and clamps 30.00 Rmt 253.82

including making good the wall, ceiling and floor etc. complete.[A] 25 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC

(SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for

41 potable water of following dia. nominal bore tube fittings and clamps 10.00 Rmt 447.72

including making good the wall, ceiling and floor etc. complete.[A] 40 mm.

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Providing laying and jointing in true line and level 110 diameter U.P.V.C.

SWR Type B pipe confirming to IS 13592-1992 with one end plain and

other end socketed with rubbering, & fitting conforming to ISI 14735-1999

of approved make for drainage system pipe line, pipe shall be jointed with

each other with rubber lubricant, pipe shall be fixed on wall using of PVC

clamp of the size 110 mm diameter x 149 mm length x 145 mm high at

every 2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement including cost of

Providing laying and jointing in true line and level 160 diameter U.P.V.C.

SWR Type B pipe confirming to IS 13592-1992 with one end plain and

other end socketed with rubbering, & fitting conforming to ISI 14735-1999

of approved make for drainage system pipe line, pipe shall be jointed with

each other with rubber lubricant, pipe shall be fixed on wall using of PVC

clamp of the size 160 mm diameter x 210 mm length x 196 mm high at

every 2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement including cost of

Providing and fixing chromium plated brass Angle cock comman with

44 flange of approved quality including fixing in pipe line etc complete 15mm 10.00 Each 813.05

Providing and fixing chromium plated brass Metropote including fixing in

pipe line etc. complete.(ii) 40mm dia.

Providing and fixing chromium plated brass half turn Bib cock including

fixing in pipe line etc. complete.(ii) 15mm dia.

Providing and fixing chromium plated brass Jet spray heavy duty with S.S.

47 Braided hose 60 cm long comman with flange of approved quality including 2.00 Each 696.90

fixing in pipe line etc complete.

Providing and fixing Single Lever In-Wall Diverter and in-wall part Combo |

Exposed Part Kit with Top Button + Concealed Body | 40mm Cartridge |

Chrome Finish | Solid Brass | Bathroom Wall Diverter with fitting of

standard quality as directed by engineer in charge including Concealed

Body for Single Lever High all materials and labours etc complete

Providing and fixing Swan neck type with swivel spout pillar cock with

49 hook with fitting of standard quality as directed by engineer in charge 2.00 Each 1626.10

including all materials and labours etc complete. (i) 15mm

Providing and fixing plated brass shower rose with 15mm or 20mm

inlet.(A) 150mm X 150 mm. Each in pipe line of standard quality as directed

by engineer in charge including all materials and labours etc complete.

Providing and fixing PVC Cowl vent of following dia etc complete as

directed. (B) 100 mm Dia.

Providing and fixing PVC SWR Nahni Trap IS 14735 for drain - 100 mm

diameter with jali of the following nominal diameter of self cleansing design

with C.I. screwed down or hinged grating including the cost of cutting and

making good the walls.

Providing and fixing plated brass half turn Twoway Bib cock with fixing in

53 pipe line of standard quality as directed by engineer in charge including all 2.00 Each 1962.43

materials and labours etc complete..(i) 15mm dia.

Providing and fixing wash basin with pedestal of std. Height with single

hole for pillar tap with C.I or M.S brackets painted white / fixing in granite

platform including cutting holes and making goods the same including C.P.

brass waste and waste pipes (A) Vitreous china. including 15 mm dia Pillar

tap and Stop cock (II) Flat back washbasin 550 mm x 400 mm size (I) in

white or colour.

Providing and fixing SS Sink Glosy ASIS 304 Grade x 1mm thick with over all

size 610 x 460 mm & bowl size 560 x 410 x 200 with single hole for pillar

55 tap Fixing in sanwich platform including cutting holes and making goods 1.00 Each 2398.00

the same, 15 mm dia pillar tap. Stop cock 15 mm dia, necessary fixtures,

connections and waste pipes etc complete.

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Provision and fixing water closet squatting orissa type W.C. pan size

580mm integral footrest and 100 mm P or S trap and including 25 mm dia

56 CP brass flush valve and GI inlet connection etc. comp. (A) Vitreous china 1.00 No 1317.56

long pattern white or color (Hindustan, Cera, Parryware or equivalent).

Providing and fixing wash down water closet (European W. C. pan) with

integral "P" or "S" trap and PVC fushing cistern with fittings etc comp incl

plastic sheet cover including jointing trap with pipe in cm 1:1 and

connecting cistern with closet & Jet spray heavy duty with S.S. Braided hose

60 cm long & 2 No. 15 mm dia Stop cock (a) Vitreous china in white or

Providing erecting and fixing double coated Syntex or equivalent PVC. (ISI)

58 mark water tank of reqd capacity each with all necessary fittings & 1000.00 Ltr. 3.95

connection etc. comp on terrace.

Providing and fixing 600 mm x 450 mm bevelled edge mirror of superior

59 glass mounted on 6 mm thick plywood sheet or PVC framing and fixed to 2.00 Each 859.41

wooden plugs with C.P brass screw and washers.

Providing and fixing C.P. brass towel rail complet with C.P. brass brakets

60 fixed to wooden plugs with cpbrass screws (B) 600 mm X 20 mm size. 2.00 Each 616.42

Providing and fixing S.W. Gully trap with C.I. Grating brick masonary

chamber and water tight C.I. Cover with frame of 300 mm. X 300 size

(inside) with standard weight (I) Square mouth traps (C) 100 mm. X

mm size P type.

Constructing brick masonary chamber for under ground C.I. Inspection

chamber and bends with bricks having crushing strength not less than

Kg/cm2 in cm. 1:5 C.I. Cover with frame (light duty) 455 mm. X 610 mm.

Internal dimensions, total weight of cover with frame to be not less than

Kgs. weight of cover 23 Kg. and wt. of frame 15 Kg) R.C.C. top slab with 1:2:4

mix(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm. size )

foundation concrete 1:5:10 inside plaster 15 mm. thick with cement mortar

1:3 finished smooth with a floating coat of neat cement on walls & bed

concrete etc. complete. (I) inside dimensions, 455 mm. x 610 mm. And

mm. Deep for single pipe line.

Constructing brick masonary chamber for under ground C.I. Inspection

chamber and bends with bricks having crushing strength not less than

Kg/cm2 in cm. 1:5 C.I. Cover with frame (light duty) 455 mm. X 610 mm.

Internal dimensions, total weight of cover with frame to be not less than

Kgs. weight of cover 23 Kg. and wt. of frame 15 Kg) R.C.C. top slab with 1:2:4

63 mix(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm. size) 1.00 No 3660.76

foundation concrete 1:5:10 inside plaster 15 mm. thick with cement mortar

1:3 finished smooth with a floating coat of neat cement on walls & bed

concrete etc. complete. (II) Inside dimensions 500 mm. x 700 mm. &

mm. deep for pipe lines with one or two inlets.

Applying two coats of putty & two coats of primer of approved brand and

manufacture on new wall surface to give an even shade including

thoroughly brushing the surface free from mortar dropping and other

foreign matter and sand papered smooth..

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly brushing

the surface to remove all dirt, and remains of loose powdered materials etc

Providing and Fixing Single Shutter Door comprising 35 mm thick Solid

Core Wooden Flush Shutter conforming to IS:2202 and manufactured by an

ISI-approved manufacturer. The shutter shall be factory made and finished

with 1.0 mm thick decorative laminate of approved shade and texture on

both faces. All edges of the shutter shall be finished with 6 mm thick

machine-glued, polished PVC edge beading

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Providing & fixing Colour Anodised Alluminum sliding window system

Domel or Equivalent 27 series Four Track (3 Glass Shutters + 1 Mosquito

Mesh Shutter) window as per shown in elevation with outer frame section

no.21401 @ Wt 1.591 Kg/Rmt & Sliding shutter style section no 21481 @

68 Wt 1.02 Kg/ Rmt, interlock Section no. 19442 @ Wt 0.33 Kg/ Rmt with 5.40 Sqm 7782.05

fixing of 5 mm thick tranparent plain float glass with tranparent silicon

sealant, Alluminium powder colour coated fiting with etc complete as per

instruction of Engineer in charge & approved make.

Providing & fixing Colour Anodised Alluminum sliding window system

Domel or Equivalent 27 series Three Track (2 Glass Shutters + 1 Mosquito

Mesh Shutter) window as per shown in elevation with outer frame section

no.21401 @ Wt 1.591 Kg/Rmt & Sliding shutter style section no 21481 @

69 Wt 1.02 Kg/ Rmt, interlock Section no. 19442 @ Wt 0.33 Kg/ Rmt with 6.30 Sqm 6852.85

fixing of 5 mm thick tranparent plain float glass with tranparent silicon

sealant, Alluminium powder colour coated fiting with etc complete as per

instruction of Engineer in charge & approved make.

Providing and fixing Coloured Anodised Alluminium sectional louvered

ventilator with frame size 60mm x 60mm/100mm x 30mm and 5mm thick

Bajari glass and Coloured anodised alluminum louvers fixture and hold

fasting etc complete.

Providing and fixing Safety grills & Gate of required pattern for windows /

Door using 12 mm dia M.S polished bars, Angles / pipes for frame as

71 directed & spacing as per Design / Drawing or as directed by engineer in 788.30 Kg 115.36

charge and hold fasting with coach bolts including one coat of primer and

two coats of mattfinished oil painting etc complete.

Providing and fixing C.I. Manhole cover 0.60m x 0.45m size having weight

not less than 35 kgs.

Providing and laying integral cement based water proofing of average

mm thick in proper slope as per specifications given below: a) cleaning RCC

slab and applying neat cement slurry mixed with waterproofing compound

(b) providing and laying brickbat coba in CM 1:4 mixed with water proofing

73 compound and curing for a period of 72 hours. c) laying of 25mm thick PCC 104.60 Sqm 651.45

1:1.5:3 mix with 6mm and down size coarse aggregate and water proofing

compound, finishing smooth, making half round vata at the junction of

parapet wall and slab, and curing for 10 days.

Construction of Septic Tank (3.0 m x 3.0 m x 1.5m) using hollow brick

masonary wall, covering with preast RCC slab including jointing the slabs

with pointing and providing 110 diametre U.P.V.C (Type B) Connecting the

line upto Manhole etc. complete

Providing 10mm wide groove /notch as per design in plaster including

finishing the same etc complete for all height.

Brick work using common burnt clay building brick shaving crushing

76 strength not less than 35kg./Sq.Cm. in super structure above floor two level 21.70 Cum 4568.40

in Cement Mortar 1:6. (1-Cement : 6- fine sand)

Steel work, welded in built up sections framed work including cutting,

hoisting,fixing in position and applying a priming coat of red lead paint.

(D)In trusses and trussed purlins, upto 25 M. span and 15 M. ovarall height.

Providing corrugated G.I. sheets roofing fixed with galvanized iron "J" or "L"

hooksbolts and nuts 8mm diameter with bitumen and G.I. limpet washers,

filled with white lead complete excluding the cost of purlins rafters and

trusses (1) 0.80mm thick sheet

Providing and fixing pre-cast Rubber Dye inter locking concrete block

mm thick with grade of concrete M300 pnumatic compressed by

mechanically pressed and as per approved design Conforming to IS

15658:2006 including 35 mm sand layer for levelling and filling the joint

with sand in proper line and level as per guidlines of IRC SP 63 : 2018 etc

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Applying priming coat over new steel and other metal surface after over

and including preparing the surface by thoroughly cleaning oil, grease dirt

80 and other foreign matter and scoured with brushes fine steel wool, scrapers 42.00 Sqm 37.62

and sand paper with ready mixed priming paint brushing red lead

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint brushing, interior to give enamel paint

brushing,interior to give an even shade including cleaning the surface of all

dirt, dust and other foreign matter

Providing and fixing kitchen platform (SS 304 Grade) basket having size 16"

82 x 20" of plate 8" depth including telescopic channel, fixing and fasteners 1.00 Each 3282.50

etc. complete approved by Engineer-in-Charge.

Providing and fixing Kitchen platform (SS 304 Grade) basket having size

83 16" x 20" of partition 6" depth including telescopic channel, fixing and 1.00 Each 2878.50

fasteners etc. complete approved by Engineer-in-Charge.

Providing and fixing Kitchen Platform (SS 304 Grade) basket having size

84 16" x 20" of plain 4" depth including telescopic channel fixture and 3.00 Each 2727.00

fasteners etc. complete approved by Engineer-in-Charge.

Providing and fixing Kitchen Platform (SS 304 Grade) having size 16" x 20"

or 17" x 20" of cutlari 4" depth or partition 8" depth including telescopic

channel fixture and fasteners etc. complete approved by Engineer-in-

Providing and fixing wooden cupboard fabricated from 18/19 mm thick

BWP/BWR grade plywood (or approved equivalent), finished with 1.0 mm

decorative laminate on all exposed external surfaces and 0.8 mm

laminate/white balancing laminate on internal surfaces. All exposed edges

shall be finished with 2 mm PVC edge banding. The work shall include

86 shelves, partitions, shutters, backing (12 mm plywood where required), SS 10.40 Sqm 12467.77

hinges, telescopic drawer channels, handles, magnetic catch, locks, screws,

adhesives, polishing of exposed wooden members (if applicable), and all

necessary accessories, complete in all respects as per approved drawings

and the direction of the Engineer-in-Charge

Providing and fixing modular kitchen base cabinet using 18/19 mm thick

BWP (Boiling Water Proof) plywood for carcass, sides, bottom, top, shelves,

partitions and shutters. All exposed external surfaces shall be finished with

1.0 mm thick decorative laminate, and internal surfaces with 0.8 mm white

balancing laminate. Exposed edges shall be finished with 2 mm PVC edge

banding. SS 304 soft-close hinges, SS handles, telescopic drawer channels

(where applicable), magnetic catch, cabinet lock, screws, approved

adhesive, skirting, all necessary hardware, fabrication, installation, testing

and complete in all respects as per approved drawings and the direction of

the Engineer-in-Charge.

Providing and fixing Roman Blind Curtain for window with using of high

quality of fabrics Aeroma Plain -II Product Code: 206685 or equivalent

88 quality including fixing of Top & Bottom roller rod as per requirement of 9.80 Sqm 2525.00

best quality and using of all other necessary materials as directed by

Engineer Incharge.

Supplying and placing 3 seated sofa having size 1900 mm X 750 mm X

mm with using of BWP Plywood 18/19 mm thick, 40 Density Foam sheet of

89 150 mm thick, Imported Velvet Solid Fabric 220gsm, with using all 2.00 No 25250.00

necessary material carting, loading and unloading etc complete as directed

by Engineer incharge.

Supplying and placing 1 seated sofa having size 750 mm X 750 mm X

mm with using of BWP Plywood 18/19 mm thick, 40 Density Foam sheet of

90 150 mm thick, Imported Velvet Solid Fabric 220gsm, with using all 1.00 No 9090.00

necessary material carting, loading and unloading etc complete as directed

by Engineer incharge.

Supplying and placing Center Table having dimension 750 mm X 750 mm X

450 mm including using of 25 mm thick BWP Plywood, Support of 50 mm

thick plywood (2 mm X 25 mm), egde cover with indian teakwood batten

patti, 12 mm thick tuffen tint glass, wooden polish using of all necessary

required material as directed by Engineer Incharge

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Providing and fixing TV Cabinate as per Detailed Drawing having size

mm X 2850 mm and 400 mm deep, with Shelf and Fluted laminates

including using of 18/19 mm thick BWP Plywood 1 mm thick laminates,

92 Fluted Laminates 1.25 mm thick, indian teakwood batten patti, wooden 1.00 No 97948.10

polish as per requirement finish the same including using for necessary

materials, tools and equipments as directed by Engineer incharge.

(Consider Elevation/Front Area)

Plantation of Bottle Palm 12 Feet Hight in soil incl digging (21" X 21" X 21")

size pits, preparing soil, providing and mixing organic fertilizers, watering

planting and filling the pits as per direction including etc complete.

Plantation of Foxtail Palm 12 Feet Hight in soil incl digging (21" X 21" X

21") size pits, preparing soil, providing and mixing organic fertilizers,

watering planting and filling the pits as per direction including etc

Plantation of Vinchhiya Palm 12 Feet Hight in soil incl digging (21" X 21" X

21") size pits, preparing soil, providing and mixing organic fertilizers,

watering planting and filling the pits as per direction including etc

Plantation of Green Machera Plant in soil incl digging (21" X 21" X 21") size

pits, preparing soil, providing and mixing organic fertilizers, watering

planting and filling the pits as per direction including etc complete.

Plantation of Golden Morpankhi Plant in soil incl digging (21" X 21" X 21")

size pits, preparing soil, providing and mixing organic fertilizers, watering

planting and filling the pits as per direction including etc complete.

Providing, Supplying and laying Land Scaping work, Different kind of

Plants and Shrubs with well grown plant min 600mm hight and necessary

98 garden soil,FYM (farm yard manure) required depth Excavation as per 12.00 Sqm 1363.50

specification,design and directed by Architect and Authority

Plantation of Euphorbia Plant in soil incl digging (21" X 21" X 21") size pits,

99 preparing soil, providing and mixing organic fertilizers, watering planting 5.00 No 2111.91

and filling the pits as per direction including etc complete.

Plantation of Golden Morpankhi Plant (15" x 16" Size) in soil incl digging

(15" X 16" X 16") size pits, preparing soil, providing and mixing organic

fertilizers, watering planting and filling the pits as per direction including

Lawn Grass:- Filling the area upto the depth of 23 cm. with good quality of

field fertile soil, breaking the clods leveling the area, free from stone, grass

roots etc. and farm yard manure at the rate of 5 cu.mt. per 100 sq.mt. mixing

the same with layer of soil, leveling rolling, pre-planting, watering etc and

planting the lawn grass of approved variety at 10 x 10 cm. distance etc

Providing and fixing pre-cast concrete kerb stone of gray cement based

concrete block 30cm length,30cm height and 15cm thick of M250 grade

102 concret as per approved design and including excavation for fixing in 41.20 Rmt 374.92

proper line and level,filling the joint with C:M 1:3 (1cement: 3 fine sand) etc

Providing and Constructing a junction chamber of size 0.35 x 0.35 x 0.60 mt,

including connecting rainwater pipes, half brick work with plaster & C.C.

1:2:4 flooring bed 50mm and covered with RCC slab 100mm thick incl. all

labour, material, excavtion etc. complete.

Providing & Constructing filter chamber of size 2.06 x 1.21 x 1.20 mt.

including connecting rain water pipes, half brick work with plaster & C.C.

1:2:4 flooring bed 50mm and covered with RCC slab 100mm thick incl. all

labour, material, excavation etc. complete.

Providing & Constructing percolation sockwell of 2.54 mt internal clear

diameter and 5.00 mt depth including honey comb brick masonary in C.M.

1:6, R.C.C. top slab of 10 cm thick filling with gravel etc. complete incl. all

labour, material, excavation etc. complete.

Demolition including stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift. (i) R.C.C. work

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Dismentling steel work including distempering and stacking the materials

with all lead and lift.

Demolition of Brick work and stone masonry including stacking of

108 serviceable materilas and disposal of unserviceable materials with all lead 91.00 Cum 576.29

and lift.(ii) In Cement Mortar.

Dismentling doors, windows, ventilators etc. (wood or steel) shutters

including chowkhats architraves, holdfasts and other attachment etc.

complete and stacking them within all lead and lift.(i) Not exceeding 3Sq.M.

110 Carriage of Murrum (more than 10 ton) 56.50 Cum 45.53

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 kV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in below type of pipe erected

with 6A Modular type switch / bell push & accessories and earth continuity

of following type, erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed. (f) with medium class Rigid

PVC pipe and accessories erected concealed in wall/ceiling complete, Cat.

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green)

both are of .ISI marked 1.1 kV Grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type electronic fan regulator

mounted and accessories with earth continuity of following type erected

112 on PVC / Metallic/Wooden box, single mounting base frame covered with 6.00 Pt. 809.01

textured/metallic/white front plate modules erected on / in wall / ceiling

as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete, Cat. III

Providing following type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame covered with textured /

113 metallic/white front plate , modules erected with necessary connections as 10.00 Ea. 25.25

per site situation directed by Engineer In charge. (7) Blank Plate Single,

114 (9) 16 Amp. SP one way switch, Cat.III 9.00 Ea. 180.79

115 (10) 6/16Amp. Universal socket, Cat.III 9.00 Ea. 199.98

116 (4) TV Co-axial Socket outlet, Cat.III 3.00 Ea. 160.59

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin

socket erected on PVC / Metallic/Wooden box, single mounting base frame

117 covered with textured / metallic/white front plate modules erected on / 13.00 Pt. 309.06

in wall / ceiling with following type accessories, Cat. III

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following

size complete to be erected on/in wall or ceiling erected with necessary

118 PVC fittings & Junction boxes fixed with adhesive solution & Clamps with 100.00 Mtr. 24.24

following dia of pipes, in approved manner as directed (a)20 mm

Providing and erecting Mains with 1.1 kV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size, (A) With medium class Rigid PVC pipe and

accessories, (b) 2 wire 2.5 sq. mm

Providing & Erecting approved make following size of TV Co-axial flexible

cable comprising inner conductor of solid bare copper insulated with Foam

120 PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids 50.00 Mtr. 62.62

@ suitable coverage overall sheathed with black PVC insulation. (e) RG-11

121 Decorative call bell Ting-tong box type 250 volts complete erected 1.00 Ea. 71.71

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt

to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium

die cast powder coated and high U.V. & corrosion resistance with diffuser

with company mark/name 160V to 270V, Power Factor more than 0.95,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.) (A)

Tube Light with integral driver (v) 36-40 Watts, Surge-2 kV, IP-20,

conventional 4 feet

Supplying and erecting led lamps with following wattage capacity of 220 to

240 voltage, minimum 15000 burning hours life, 500 V in built-surge

123 protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 5.00 Ea. 112.11

lamp holders, pf >= 0.5, (A) LED Lamps integral type, with PC diffuser

suitable LAMP holder, (ii) 5 to 8 watts, Cat-III

Supplying and erecting LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or embossed 160 to

270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

124 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED 6.00 Ea. 2843.15

driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Street Light (IP-65), Surge

protection -4KV integral and ,Light must have 440VAC line supply with over-

voltage protection. (i) 36 - 47 watts

Supplying KITKAT pattern porcelain cut-out fuse with base of following

125 current capacity erected on existing block board.(iii) 32 A. 250/500 V. 2.00 Ea. 73.73

providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

Providing & erecting 240 V MCB double pole switch for motor & inductive

127 load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in 3.00 Ea. 329.26

existing box having following capacity (A) 6 to 32 Amp.

128 (B) 40 Amp. Cat.III 3.00 Ea. 362.59

Plastic enclosure fitted with DIN rail suitable for incorporating Three /Four

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

130 appropriate nos. of MCBs.(The DBs should be used of same company of MCB 1.00 Ea. 1680.64

to be used) suitable for, (A) single phase incoming and horizontal single

phase outgoing (b) sheet steel double door (IP-43) (v) 16 way

providing and erecting Approved make RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA

and suitable for operation on single phase 240 V,50Hz. having characteristic

of quick action & tripping with all advance feature & do not incorporate any

electronic component. for following Max. rating erected as directed, (ii)

40Amps. DP , Cat. III

Providing and erecting Annealed bare Copper wire 4.064mm to 1.626mm.

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Supplying & erecting earth pit of minimum bore dia.150mm size approved

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having

200-250 Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive compound with

high charge dissipation suitable for following type of applications with

chamber and heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly stamped

and signed by agency and officer Incharge has to ensure the value of

earthing resistane mentioned in test Certificate) & having back filling

compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm /

meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load &

dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing

compound should be capable to retain moisture for long time Necessary

test report must be submitted by Agency. (a) For Electrical Installation up

to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting FRLS-XLPE(IS:7098)(I)-88 ISI armoured cable

Aluminium conductor for 1.1 kV. to be laid on wall with necessary clamps

or in existing trench / pipe of following size of cables. (C) 2 core 10 Sq. mm

Making trench in soft soil of suitable width of 90 cm deep for laying cable or

135 locating the fault all over the run and back filling the same and making the 70.00 Mtr. 55.55

surface as normal ground.

Providing & laying approved make Double walled corrugated pipes (DWC)

of polyethylene(conforming to IS 14930 II )with necessary connecting

136 accessories of same material at required depth in existing trench for laying 75.00 Mtr. 62.62

of cable. below ground / road surface for enclosing cable (A)50 mm outer

Providing & laying approved make ISI marked HDPE 6Kg / cm2 (Class-3)

as per IS:4984:1995 PE-80 to be erected at road crossing on or floor as

directed for laying of cable. The pipes as following size of dia & weight per

mtr. (A) 40 mm inner Dia.

Supply, Installation, Testing and Commissioning of suitable sweep, BEE

Star rated, Ceiling fan with Brush Less Direct Current (BLDC) permanent

ferrite magnet Motor, class of insulation: B, Rust free 3 nos.Aluminium

blades, 2 nos. canopies, shackle kit with earthing provision, copper

winding, Power factor not < 0.9, Service Value (CMM/W) minimum 6.85, Air

delivery minimum 215 CMM, 350 RPM,230v (tolerance as per IS : 374-

138 2019), THD < 10%, compitible with electronic regulator unit for Speed 6.00 Ea. 2629.03

Control and all remaining accessories including safety pin, nut bolts,

washers, temperature rise = 75 °C (Max.), suitable for 140 to 285 Voltage

and rectifier circuit with surge, over current and overload protection ,

Hz, Single phase AC Supply, earthing etc. Complete as required.[ Make shall

be approved by Engineer in Charge] (A) 1200 mm Sweep (48")

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in RCC

slab with Making the site as original.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to

the RCC bars up to 50mm length each side and pierced through a 16 Gauge

M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with

necessary finishing.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan

Supplying & erecting approved make SMC press moulded composite FRP.

loop-in, loop-out approx. 2mm thick box complete with Bakelite connector

strip 5way(3P+N+E),DIN rail for mounting mob & hinged doors as per

142 requirement having locking arrangements with mounting clamp with nuts, 6.00 Ea. 524.19

bolts & washers suitable for erection on pole with cable clamps& earth bolt

of following size of box. (E) 200mm x 140mm x 125mm [deep]

Name of work :- Construction of New Category 'D' Type TDO Quarter at Ta: Ghogha, Dist: Bhavnagar

BILL OF QUANTITIES

Item Description Quantities Unit Item Rates Amount

Supplying and erecting Direct - On - Line Starter with 18 A. rating contactor

and with 3.5 Amp. 18A range directly operated in totally insulated elegant

143 enclosure for single phase operation up to 3 HP as per IS 13947 complete 1.00 Ea 2100.80

erected on P.W. Block with necessary connection. Cat-lll

Supplying & erecting approved make self-priming domestic monoblock

water pump with 1 H.P motor, suitable for operation on 230 volts, 50 Hz. AC

144 supply with metallic flange, and M.S. impeller delivery and following 1.00 Ea 8447.64

discharge (a) 40 LPM at 24 mtrs. head suitable for 25mm dia. Delivery

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible

145 Submersible copper cable approved make of following Size. (B) 3 Core x 30.00 Mtr. 104.03

Providing Water proof straight Joint in PVC insulated flat flexible copper

146 cable by using insulating material, water proofing material, & making the 1.00 Ea. 189.88

joint complete. (A) Up to 10Sq. mm

I \ We am \ are willing to carry out the work at ……………………… % above\bellow percent (Should be written in figures and words) of the

estimated rate mentioned above. Amount of My\Our tender works put as under.

Estimate Amount Estimate Amount

Put to tender Rs___________ Put to tender Rs___________

(* Please strike out whichever is not applicable).

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which no

extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt.G.R.: PRC-10/2017 Cement

Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design the

cost of difference of cement consumption have been deducted from the rate of original item at the rate of input rate mentioned in all

5. Credit of dismantled materials of amount of Rs. 43829.50 must be recovered from Contractor's first R.A Bill.

Dated Signature of Deputy Executive Engineer Executive Engineer

the Contractor. Panchayat (R & B) Sub Division Panchayat (R & B) Division

Bhavnagar Bhavnagar