Selection of Construction and Management Agency (CMA) for Construction, Operations & Maintenance Services of the Gujarat Vandana Museum at Ekta Nagar, Narmada District, Gujarat

GUJARAT VANDANA MUSEUM, GUJARAT (GVM)

BILL OF QUANTITIES

SR NO PARTICULARS TOTAL AMOUNT

2 STRUCTURAL WORK 0

3 MASONRY WORK 0

4 WATERPROOFING WORK 0

5 FLOORING WORK 0

8 ROOFING & CEILING 0

9 FINISHING WORK 0

10 ALUMINIUM WORK 0

11 PLUMBING WORKS 0

12 FIRE FIGHTING WORKS 0

13 ELECTRICAL WORKS 0

14 ELV & ICT WORKS 0

15 HVAC WORKS 0

16.1 HORTICULTURE 0

16.2 IRRIGATION 0

16.3 WATER BODIES 0

18 DEMOLITION & DISMANTLING WORK 0

19 BARRICADDING WORK 0

20 MISCELLANEOUS WORK 0

21 KITCHEN EQUIPMENT 0

22 BORE WELLS 0

24 ACOUSTICS & AV WORK 0

25 SIGNAGE & WAY-FINDING 0

26 SPECIAL LIGHTING 0

27 FURNITURE, FIXTURE & EQUIPMENT 0

SUB TOTAL - BUILDING CONSTRUCTION WORKS 0

Add : GST 18% 0

TOTAL OF BUILDING CONSTRUCTION WORKS 0

23 INTERIM MAINTENANCE PERIOD 0

24. OPERATION & MAINTENANCE for 5 YEARS 10% 0

SUB TOTAL - OPERATION & MAINTENANCE 0

Add : GST 18% 0

TOTAL OF OPERATION & MAINTENANCE 0

Amount in words -

SR. NO. PARTICULARS UNIT RATE TOTAL QUANTITY TOTAL AMOUNT

Work and rate shall include the following:

A. Setting out works, erecting profiles, etc.

B. Site clearance such as cleaning of shrubs, brushwood, small trees not exceeding 30 cm in girth measured at one meter above ground.

C. Forming (or leaving) DEAD MEN or TELL-TALES in borrow pits and their removal after measurements.

D. Forming or leaving steps in sides deep excavation and their removal after measurements.

E. Excavation for insertion of planking and strutting.

F. Removing slips or falls in excavation.

G. Dewatering (bailing or pumping out water in excavations from rains, sub-soil water, etc.)

H. Slinging or supporting pipes, electric cables, etc. met during excavation or carrying out of any item of work.

I. Dressing, trimming of sides, leveling or grading and ramming of bottoms.

All items of excavation, filling, etc. shall be carried out in dry site only. The contractor to note that dewatering wherever required or ordered by the RE shall be part of the respective item and the contractor must make necessary allowance in his quoted rates. No additional cost on account of dewatering of any nature and for any reason shall be payable throughout the contract.

Anti-termite treatment shall be measured in sq m once for the actual plinth area in the plan. The rate will include,

· Method of working as per the approved manufacturer

· Number of operations required

· Application at various levels and stages

· Guarantee for 10 years in approved form

Carting away all surplus excavated material outside the plot area including loading, transportation, unloading etc. complete. (Volume will be measured on compacted basis, on the basis of approved excavation quantities and filling quantities.

Allowance for voids shall be included in quoted rates only. Contractor should locate suitable area for dumping the material at his own cost.

1.1 Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft soil Cum 43,913.00 0

1.2 Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 Meter lead.(B) Dense or Hard soil Cum 14,627.00 0

1.4 Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 Meter lead.(B) Dense or Hard soil Cum 10,728.70 0

1.5 Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 Meter lead.(D) Soft rock not requiring Blasting Cum 1,813.30 0

1.6 Excavation for foundation depth more than 5.0 m for excavation for foundation including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 m lead.(D) Soft rock not require Blasting Cum 5,717.60 0

1.7 Excavation for foundation depth more than 5.0 m for excavation for foundation including sorting out and stacking of useful materials and disposing of the excavated stuff upto 50 m lead.(E) Hard Rock Cum 1,429.40 0

1.8 Add extra for Disposing off the excavated stuff of above items for lead of (A) 50 m to 200 m Cum 70,000.00 0

1.12 Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each disposited layer by ramming and watering. Cum 29,023.00 0

1.13 Filling in foundation and plinth with murrum or selected soil in layers of 20cm. thickness including watering, ramming and consolidating etc. complete. Cum 7,892.00 0

1.14 Anti-Termite System:Providing and laying of permanent piping technology anti-termite treatment before flooring work by installing LLDP (Low linear density polyethylene) tube of 8 mm O.D. & 6.4 mm 1.D. with inbuilt pressure compensation chip every 30 cm interval in the tube, having working pressure of 2 Kg/cm2 and release rate of 1.9 Itr/hour fixed by P-clips and nails. The LLDP pipe shall be installed at the entire periphery of the building and at internal network of building at a depth of 20 to 200 mm under floor at every 2 to 3 mtr. c/c distance (adjusted as per building layout ) & Ends of loop pass through a PVC elbow of minimum 32 mm ID at junction box of wall and floor level, entering into a steel reinforced grooved flexible pipe of minimum 22 mm ID leading into junction box and the loops shall terminate in junction boxes & test every junction during injecting chemicals for termite control treatment. The anti termite chemical Imidacloprid 30.5% SC -Sq.mt 133.00 mix as per IS-6313 (part III) shall be injected by the pressure pump diluted with water @ 10.5 ml/5 ltr of water at the rate of 2 Kg/sq.cm @ 5 Ltr/SMT. The contractor shall submit approved line plan for piping system and junction boxes dully approved by Engineer-in-Charge with bond of 10 year warranty.(i)Anti Termite chemical injected area (Chemical injecting incl. labour cost) (Only plinth area at Ground level shall be measured for payment) Sqm 10,847.00 0

1.17 Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

a With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 Cum 8,671.00 0

1.19 Providing and Filling with Murum in layers to required depths as directed, including watering, ramming and compacting dry density, including carrying out Laboratory 'Proctor Density' Test, etc. complete as directed by site incharge.( Consolidated thickness will be considered for payment.)

a Murum available at site Cum 81.00 0

TOTAL OF EARTH WORK 0

2. STRUCTURAL WORK

All concrete work shall be design mixed of the grade specified on drawing

The rates for PCC/RCC work shall include the following:

A. All materials with wastage & All labour. All test on materials and cube testing or any other testing as instructed by the RE / Structural Consultant as per IS.

B. All architectural effects like chases, ledges, moulds, grooves, chamfers, brackets etc. shall be created by using approved form work including making special size mould, staging arrangement, etc.

C. Work at all depths, heights and leads.

D. If different grades of concrete are used at junctions, spillover of richer concrete required from practical considerations shall be included in the rate.

E. The concrete shall include ingredient material, mixing, transporting, hoisting to any height and lowering to any depth, pumping (as detailed), pouring or laying, consolidating, leaving pockets, holes, conduits and protecting them till the next operation or completion of work, hacking the surface to provide key for further work including cleaning, wetting, surface curing, etc. and preparing construction joints. The price built-up shall include the loading, unloading, weighing and storing of cement in good conditions.

F. Admixtures as required and should conform to IS 9103.

G. Water proofing compound, as required.

H. Cement grouting with non shrink grouting compound

I. Dewatering to keep area dry.

J. The contractor shall provide and maintain laboratory at site equipped as under and staffed with qualified technicians.

· A set of standard sieves

· Measuring cylinders

· Adequate number of standard cube moulds

· Weighing machines measuring to 10 grams and upto 50 Kg.

· Oven or other apparatus to dry aggregates.

· Concrete cube testing m/c, 140T capacity, electrically operated.

2.1 Providing and laying cement concrete 1:4:8 (1- Cement : 4- Coarse sand : 8- Graded Brick bats aggregate 40mm normal size) and curing complete excluding cost of formwork in (A) Foundation and Plinth Cum 2,136.00 0

2.3 Providing and laying in position Ready Mixed M-30 grade concrete for reinforced cement conctere work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) (Cement level 475 kg ) Cum 1,370.00 0

2.5 Providing and laying in position Ready Mixed M-40 grade concrete for reinforced cement conctere work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) (Cement level 575 kg ) Cum 26,984.00 0

2.6 Providing and laying plum concrete course in plain cement concrete M-15 and evenly distributed plums of basalt or trap of size 160 mm and above up to any reasonable size to a maximum limit of 30% by volume of concrete including mechanically vibrating and compacting, centering etc. complete. ( No plums shall be allowed to be projected/protruded with in 150mm from top level of plum concrete). Cost towards formwork shall be included in the quoted rate. Cum 1,000.00 0

2.8 Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level Kg 5,745,897.00 0

2.9 Expansion Joint Covers

a ROOF SLAB TYPE-1 Providing & fixing of earthquake-resistant Series for Roof Top Covers 150 mm for Expansion Joints having Aluminum Plate at upper predrilled mounting brackets and flexible rubber support. The system should be able to perform as per the Joint size, having desired movement. This Solid all metal roof top cover should be maintenance free, hard wearing and long-lasting model for roof area. This design minimizes noise emission in windy conditions. This model has three-dimensional movement absorption. Also has vertical movement with total 100 percent movement. For Precise Transitions the system should be installed by the way of positive connection between each single length by the way of connecting pins that should ensure a flat level and precise transition. Rmt 19.00 0

b ROOF SLAB TYPE-2 Providing & Fixing earthquake-resistant Series Model -RTC Corner Profile for Roof Top Covers for 150MM Expansion Joints, the having Aluminum Plate at upper predrilled mounting brackets and flexible rubber support. The system should be able to perform for 150mm of Joint size, having desired movement This is Solid all metal roof top cover should be maintenance free, hard wearing and long lasting model for roof area. This design minimizes noise emission in windy conditions. This model has three dimensional movement absorption. For Precise Transitions the system should be installed by the way of positive connection between each single length by the way of the connecting pins that should ensure a level and precise transition. Approved Make Expansion Joint. Rmt 57.00 0

c ROOF SLAB TYPE-3 Supplying and Installation Flameline Expansion Joint system with FSL-173 Corner Profile, especially design for roof area to accommodate structural movement and ensure complete watertight. Covers for Metal Series, Floor to Corner Model, for 150mm Expansion Joints Aluminum Covers Profiles for Top Finish, having a Hard Wearing, Maintenance Free, long Lasting design having Smooth Surface. The Surface of the Exp. Joint Covers should have Sirated Surface, which should ensure to have a good Skid Resistance so that it avoids any kind of Slippages when used. The design of the Exp. Joint Cover System should be such that it should avoid any accumulation of dirt. The Exp. Joint Cover should have an Articulated Telescope Design so as to accommodate the movements in 3 direction. It should also accommodate a Vertical Movement of 10 mm. The surface of the system should be in the Mill finish. The Total Visible width of the profile should not be 173 mm & the installation Height can be of 35 mm. The system can be used for standard Rolling Loads of 1-2 Cars or Cart Wheel Loads if required. The system should have ASTM1399 E IV certification. Provision of Flameline 100% in the Joint System to have watertight joint is mandatory on the motherslab. The Sealing Strip system is specifically developed compound with ensure to absorb the Three Dimensional movement having a Total Width of 420mm. The material consists of the elastic material Butyl-Elastomer and Very high long-term heat resistance (up to +90° C)/ Very high flexibilty at low temperatures (up to –40° C)/Water pressure up to 0.5 bar/Overall resilience against chemicals:/Very good against alkali, diluted acids and saline solutions/Excellent against vapour/Very good resilience against polar solvents like alcohol/and ketone. The Sealing Strip should have the properties for sealing on the Bitumen sheets, Epoxy/PU Adhesive on Concrete & Metal. The both the side Ends should have the Protruding Fabric which should enable for the Perfect bonding/connecting with Bitumen / Epoxy/PU.Requirement all as per the manufactures design and as approved by the Engineer-in-Charge. Rmt 131.00 0

d WALL TYPE-1 (INTERNAL WALL) Supply and installation Symmetric metal wall and ceiling cover is designed for interior and Exterior applications where low-maintenance or tamper resistant applications are desired. The free-floating aluminium centre plate spans the joint and slides between retainer assemblies to allow for required movement. The cover can be anodised or powder coated in any RAL colour. Extrusion shall be of ASTM 6063 T66 standard. Can be used in a variety of wall construction including flush finish in drywall applications also. No exposed fasteners for tamper proof application. For exterior use of water barrier EPDM membrane must be installed below WP profile. Rmt 91.00 0

e WALL TYPE-2 (EXTERNAL WALL) Supply and installation Symmetric metal wall and ceiling cover is designed for interior and Exterior applications where low-maintenance or tamper resistant applications are desired. The free-floating aluminium centre plate spans the joint and slides between retainer assemblies to allow for required movement. The cover can be anodised or powder coated in any RAL colour. Extrusion shall be of ASTM 6063 T66 standard. Can be used in a variety of wall construction including flush finish in drywall applications also. No exposed fasteners for tamper proof application. For exterior use of water barrier EPDM membrane must be installed below WP profile. Rmt 123.00 0

f FLOOR TYPE-1 Providing & Fixing of the full Metal SEISMIC PAN JOINT (SPJ) System, for Expansion Joints All Aluminium Covers Profiles, having a Hard Wearing, Maintenance Free, long-Lasting design with no Shrink seal and no gasket with straight 90-degree Pan design to take 90 Degree of cut stone. The 90 degrees pan flange and side wall must be single extrusion to maintain smooth and synchronised movement of pan without any hurdle. The profile should be flushed with floor finish once installed. The Exposed Surface of the Exp. Joint Covers should have Micro Serrated Surface, which should ensure to have a good Skid Resistance so that it avoids any kind of Slippages when used. These side flanges should slide smoothly on side frame and must have single piece extrusion with pan side frame to ensure smooth movement. The Exp. Joint Cover should have a Seismic and Articulated Telescope Design so as to accommodate the movements in 3 directions. The turn bar must have 2-part assembly to provide vertical movement. It should also accommodate a Vertical Displacement and Thermal Movement of +/-20mm. The surface of the system should be in Mill finish. The Total Visible width on each Micro Serrated side will be 65mm in the form of flange to accommodate thermal movement & the installation Height will be 60 mm. The mounting brackets will be predrilled. The depth of Pan infill will be 30mm.The system can be used for standard Rolling Loads of 1-2 Cars or Cart Wheel Loads, must be FEM Stress tested by Design load (Cleaning Machine), Wheel load: 2,5 KN – Wheel contact patch: 10x1,0cm, qd=2500 x 1,5/(100x10) = 3,75 MPa. The system must have been tested for movement as per ASTM E 1399-class IV certification. The extrusion should be as ASTM 6063 T66 standards. For Precise Transitions the factory supplied slid-in connection pins should be used during the installation of the cover system. The Exp. Joint Covers/Profile shall be supplied in 3 mt. Cut Length. Rmt 42.00 0

g FLOOR TYPE-2 Providing & Fixing Floor to Corner for 150mm mm Expansion Joints, the having Solid All Metal Expansion Joint Cover. Maintenance- Free, Hard wearing and Long-Lasting, Non-Shrink Seal. The cover must be design in such a way that there should be aluminum flange in the sides and no requirement of any gasket or sealant should be there. The profiles are provided with 90° Vertical Side Walls. There Is no diagonal Cuttings of Stoneware necessary. The Exp. Joint System have three-dimensional movement absorption, easy to install with optimized design allows for easy and safe installation of the centering bar. Connection pins to ensure even installation with respect to both, height and width. The system must have tested for movement as per ASTM E 1399/ ASTM 1399 M, class IV certification. The extrusion should be as ASTM 6063 T66 standards. The Exp. Joint Covers/Profile shall be supplied in 3 mt. Cut Length. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by the Engineer-in-Charge. Rmt 61.00 0

h FLOOR TYPE-3 Providing & fixing of the Covers for Interior Metal Series, Floor to Floor Model, for 150 mm Expansion Joints Aluminum Covers Profiles, having a Hard Wearing, Maintenance Free, and long lasting design. The surface of the Exp. Joint Covers should have Serrated Surface for Skid Resistance and should be ADA Compliant. The design of the Exp. Joint Cover System should be such that it should avoid any accumulation of dirt. The Exp. Joint Cover should have an Articulated Telescope Design so as to accommodate the movements in 3 directions both Horizontal & vertical movement. The system should be in 6063 alloy in Mill finish. The system can be used for standard pedestrian load. The side profile should have a MULTI HOLE mounting bracket allowing for secure fixing and Flexible anchoring and excellent bonding with given slab surface/masonry/epoxy bedding. For Precise Transitions the factory supplied slid-in connection pins should be used during the installation of the cover system. Rmt 35.00 0

i FLOOR TYPE-4 Providing & Fixing Covers for Interior Metal Series, Model - FSL 113, Floor to Wall Corner Model, for 100 mm Expansion Joints Aluminum Covers Profiles, having a Hard Wearing, Maintenance Free, long Lasting design. The Surface of the Exp. Joint Covers should have Serrated Surface for Skid Resistance and should be ADA Compliant. The design of the Exp. Joint Cover System should be such that it should avoid any accumulation of dirt. The Exp. Joint Cover should have an Articulated Telescope Design so as to accommodate the movements in 3 directions. The total Horizontal Movement should be 45 mm (-/+ 22.5 mm). It should also accommodate a Vertical Movement of 10 mm. The system should be in 6063 alloy in Mill finish and the total exposed surface of the profile should not be more than 113 mm (+/- 5 mm) & the installation Height can be of 20/35/50 mm. The system can be used for standard Rolling loads of private Cars or Cart wheel loads. The side profile should have a MULTI HOLE mounting bracket allowing for secure fixing and Flexible anchoring and excellent bonding with given slab surface/masonry/epoxy bedding. For Precise Transitions the factory supplied slid-in connection pins should be used during the installation of the cover system Rmt 37.00 0

j WALL TYPE-3 (INTERNAL) Providing & Fixing Wall and Ceiling Expansion joint Covers, for 30mm to 350 mm Expansion Joints having Flexible High Quality Electromagnetic Inserts to accommodate movements. The Inserts should be Hard Wearing & temperature resistance (- 30 C to + 120 C Degree). Expansion Joint covers/ Profile insert should have a double protection from water due to its double sliding special Foldable Insert that can be installed in continuation length up to 50 RMT. The insert must be wieldable if required to connect two pieces of inserts. The height will be 20mm to accommodate surface material like plaster, gypsum, false ceiling etc. The Side Profile should have a MULTI HOLE mounting bracket allowing for secure fixing and Flexible anchoring and excellent bonding with given slab surface/masonry/epoxy bedding. Rmt 301.00 0

Form work shall be carried out as detailed in technical specification.

a) All formwork shall be fair face finished with using plywood/ Steel panels as directed by RE.

b) Exposed form work where specified shall be for Architectural finish and shall create required architectural features with the use of specially designed forms.

Form work shall be measured and paid separately except for PCC items or if stated specifically in Schedule of Rates. The quoted rate shall be applicable for all working conditions and at all heights, depths or lifts specified in the BOQ. The rate shall include the cost of materials and labour for various operations involved. The rate shall include the following, in addition to the “Measurement / Rate“ as mentioned in Technical specification:

A. All materials with wastage & All labour

B. Handling, cutting, shifting, jointing, welding etc.

C. Rigid base of plywood / steel plaster with leak proof joints

D. Steel prop or system designed staging system. (Timber / Bamboo props staging not allowed)

E. Moulds of correct size, shape with flexibility to dismantle without kicks

F. Erection at all heights, leads, lifts and depths.

G. Erection to collect line, level, plumb and within tolerances as specified.

H. Leaving pockets, holes, conduits etc.

I. Shuttering oil

J. Maintaining in position till concrete attain desired strength.

K. Temporary openings in the forms for pouring concrete and removing rubbish.

L. Fixing inserts and openings at the correct line and level and any required stage to support the same at the directed height and place.

M. Platforms, if any, required to keep check on form while the concreting is in progress

N. Cleaning the shuttering.

2.10 Providing, fabricating, erecting and fixing in position 12mm thick waterproof ply centering and shuttering true to line and level, including required height's steel propping and staging, at all heights/levels, applying shuttering removal chemical emulsion/oil as approved, required bracing, if specified chamfering exposed edges, corners of beams, columns, walls etc., making leak proof joints etc. complete, at all leads and lift. Also include safely removing and dismantling the aforesaid assembly after specified or as approved period from the day of casting of concreting to the satisfaction of the Engineer in charge. The item shall also include the required staging and supporting arrangements. Sofit of slabs shall be fairface finished with no undulation of more than 2mm permitted. Any defect noticed shall be corrected by grinding or as approved by Engineer in charge, at Contractor's cost. The staging and formwork design shall be submitted to the Enginner in charge and got approval from Structural Consultant before proceeding to erect the same. (Up to floor to floor height of 3.5m)

a i) Retaining wall/ Columns / shear walls of all shapes and size. Sqm 61,153.00 0

b iii) Beams at all levels Sqm 12,563.00 0

c iv) Slabs / chajja slab at all level. Sqm 10,551.00 0

d v) Staircase including steps Sqm 2,607.00 0

2.10.1 -Do- as per item above but using steel sheet form work

h i) Footing / Raft / Pile caps Sqm 7,624.00 0

2.11 Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).

2.11.1 a) Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) Sqm 1,000.00 0

2.12 Providing and filling with styrofoam (minimum compressive strength 9.1 T/Sqm and density of 30 Kg/cum) lightweight filling to enable casting of Double slab build-up (refer drawing A14-01, detail-19) Cum 9.00 0

2.13 Providing and fixing roofing consist of galvanized steel deck sheet conforming to IS 277:1992 used as permanent shuttering over which reinforcement steel as per structural design and drawings shall be placed and tied complete, including all necessary cover blocks, binding wire and supports required for proper placement of reinforcement. The metal deck shall be supported on structural steel beams with shear studs complete. (Structural steel members such as beams, columns, joists etc., reinforcement steel and concrete of different grades as per design shall be measured and paid separately) Sqm 15,717.00 0

2.14 Providing, transporting, hoisting and fixing at all levels precast reinforced cement concrete of M40 grade in curved vertical panels of sizes and shapes as per Drawing No. A-17-1, 2 & 3 along with Structural drawing as listed below including the cost of required centering, shuttering, reinforcement including required designed lifting anchors of approved make Halfen or equivalent, including securing the panels with tounge & groove / butt jointed as per details at the locations, fixing with 317 grade Stainless steel designed chemical anchor, nuts & bolts etc. to the structural steel framing (structural steel paid separately), the panels are to be form finihsed from inside, etc. all complete to the entire satisfaction of the EIC. (Panel Type A-1 to A-8, B-1 to B-8, C-1 to C-4 & D-1 to D-4) (external elevation area x thickness of panel shall be measured for payment) Cum 739.00 0

2.15 Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).

2.15.1 600mm dia piles Rmt 33,114.00 0

TOTAL OF STRUCTURAL WORK 0

3. MASONRY WORK

All work as detailed in Technical specifications and drawings. The rate shall include the following, in addition to the “Measurement / Rate“ as mentioned in Technical specification:

A. All materials with wastage

C. Supply & Testing of Bricks / Blocks/ Rubbles

D. Making bonds

F. Forming arches

G. Work at heights, depths, lifts and leads

H. Racking out joints

J. Required scaffolding

K. Patli beam concrete

L. Steel binding, placing etc.

M. Leaving holes for fixing pipes etc

L. Building in ends of RC or steel members and making good

3.1 AAC BLOCK MASONRY Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm to 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. Cum 500.00 0

3.2 AAC BLOCK MASONRY Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 150 mm to 500 mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. {The payment of RCC band and reinforcement shall be made for seperately).(Refer-A13/01 & Det-1/A13-08) Cum 2,432.00 0

Brick work with non modular fly ash bricks conforming to IS:12894,class designation 10 average compressive strength in super structure above plinth level up to floor V level in :

3.3 Cement mortar 1:4 (1 cement : 4 coarse sand) (Refer-A13-01 & Det-1/A13-08) Cum 1,842.00 0

TOTAL OF MASONRY WORK 0

4. WATERPROOFING WORK

Toilet Waterproofing

4.1 Providing and applying two component high performance highly flexible cementitious waterproofing coating having minimum elongation of 200% (as per ASTM D412: 2016), tensile strength >1.5 MPa (as per ASTM D412: 2016), adhesion strength > 1.2 MPa (as per ASTM D 7234:2019), water vapour transmission less than 22.6 g/m2/day (as per ASTM E96: 2022), crack bridging more than 2mm (as per EN 1062-7:2004), water permeability of 5 bar positive pressure (as per EN 12390-8:2019). The concrete surface must be brought into surface saturated dry condition (SSD). The coating shall be applied with a total consumption of 2.2 Kg/Sqm in two coats using a roller/brush on the prepared concrete substrate) sunken slab / flat slab and on walls up to 1m height. All the coats to be applied in perpendicular direction to each other and allow the coating to air cure for 3-5 days before conducting water ponding test for 24 Hrs. The system includes base preparation of cleaning and preparation of surface with the help of wire brush or grinder, brushing and removal of flacky materials, grouting the porous area with cementitious grout, sealing the minor cracks, proper coving of minimum 25mm x 25mm using polymer modified mortar between slab and wall junctions followed by the application of waterproofing coating as per manufacturers specification and methodology. (Location : Toilets) Mode of measurement will be actual area treated. Sqm 1,986.00 0

Rate shall including required testing as mentioned below 1. Testing on mother slab, grouting - TEST 1 2. After completion of coating - TEST 2 3. Water for testing to be arranged by Contractor

Contractor to provide guarantee for 10 years Rs.500/- stamp paper in approved proforma. Water for testing shall be in part of Contractor's scope.

4.2 Providing and filling light weight AAC bats (of size 40-60 mm) with cement mortar mixed in the ratio 1:3:6 (1 cement : 3 coarse sand : 6 block bats) including mixing of approved water proofing compound in recommended proportion. The laid brick bat mix shall be well rammed and compacted as required. Further surfaces shall be screeded with cement concrete mix 1:1.5:3 (1 cement : 1.5 coarse sand : 3 stone grit of size 6 mm and below by volume) admixed with approved integral water proofing compound in recommended proportion, laid to an average thickness of 25mm and finished smooth or ready to receive finish material as specified. Care shall be taken prior to filling all pipes passing through sunk portion such that the pipes are pressure tested by maintaining pressure for 24 hours and junctions of pipes passing through walls, slabs are well grouted and sealed. Cum 1,472.00 0

This shall be tested by ponding water for required depth and maintaining for 72 hours. (Rate includes cost of AAC bats, cement mortar, top screed, labour charges for working at all levels, leads and heights). For payment the area of sunken slab and the depth of filling including the thickness of screed shall be measured.

4.3 Water Tank waterproofing Sqm 2,842.00 0

Providing and applying two component solvent free elastomeric polyurethane resin base coating for waterproofing and protection of water tanks. The concrete surface on which the coating is being applied should be minimum 28 days old and having residual moisture content <5 %, surface should be free from loose dust, dirt, loose mortar, curing compound and achieve surface profile of CSP4 or CSP5 level. Apply two component solvent free flexible polyurethane primer on the prepared surface using roller/brush in one coat @ 100gms/m2 and let it cure of 4-12hours followed by application of 2 coats of polyurethane coating after mixing the two components. It shall be applied in two coats by roller only with a total consumption of 1.4 kg/sq.m (0.5 kg/sq.m. in 1st coat and remaining in 2nd coat). Second coat to be applied in direction perpendicular to the first coat. Let the coating cure for 3-5 days for full cure before conducting water ponding test for 24 Hrs. Gap between the two coats application shall not exceed 12 hours.

The coating shall have specific gravity of 1.2 and solids content of 100%, elongation of 100% ±10% (as per ASTM D412), tensile Strength >10Mpa (as per ASTM D412), shore A Hardness >80 (as per ASTM D 2240), positive hydrostatic pressure resistance of 5bar (as per EN12390), negative hydrostatic pressure resistance of 5 bar (as per ASTM D7088), adhesion to concrete >2Mpa (as per ASTM D7234), water absorption <0.15 % (as per ASTM D570) and certified by CFTRI as per 21 CFR 175 – 300 of US – FDA for potable water contact all as per manufacturers' specification, etc. complete.

Wall and Floor Junction Treatment: Making “V” grooves cut along the wall & slab joints for 10 x 10 mm using a hand cutter followed by cleaning the groove thoroughly and applying one coat of two component solvent free flexible polyurethane primer and filling the gap with polyurethane/hybrid polyurethane sealant in the groove. After curing of sealant, apply one coat of primer in a width of 120mm, let it cure and fix the specially coated 3-ply elastic corner Joint tape using polyurethane coating.

All tie rod shall be chipped for a depth of 50mm on both the sides of opening of wall, then completely remove the dust from the holes by blower and then fill the tie rod holes with approved non-shrink cementitious grout for full depth of hole and allow to dry for minimun 3 days. During filling of tie rod leave a gap of 10mm from the surface and the same should be filled with polyurethane/hybrid polyurethane sealant.

Treatment around pipe Core Cut Areas : All the pipes to placed / inserted in the core cut areas, shall be placed appropriately to be grouted around the cut bores.Roughening the pipe surface with hacksaw blade and applying a coat of SBR modified latex and sprinkling sand for proper adhesion. Grouting the gaps between the pipe and the core cutting by high strength non-shrink cementitious grout or micro-concrete that shall be poured into the gaps after fixing in place an effective leak-free shuttering and support. Allow the grout to set for 24 hrs. And do the moist curing for 5 days. The area around the pipes (10mm) shall be filled with polyurethane/hybrid polyurethane sealant followed by flashing treatment with polyurethane waterproofing coating and specially coated 3-ply elastomeric corner joint tape embeded between the two coats of waterproofing membrane.

All systems to be installed as per manufacturer's recommendations, etc. complete with all lead and lift for all materials and labour and as directed by PM and giving guarantee for 10 years on Rs. 500/- Stamp paper in approved proforma.

4.4 Internal surface of lift pit Sqm 474.00 0

Providing and applying in depth penetrating type crystalline slurry waterproofing system (Mix Ratio of Water : powder = 0.4), to be applied as a slurry application in 2 coats at a total consumption of approx. 1.6 Kg / sqm as per manufacturer's recommendation applied on the internal wall & floor surface of the Liftpit, to be done post construction, including cleaning of the surface as per manufacturers specification, treating the construction joints with crystalline plugging mortar, treating the honeycombs, & cracks with cementitious injections admixing expansive additive @ 225 gms per bag of cement, etc. complete. The crystalline slurry coating shall have following minimum properties: 1. Water head resistance > 70m as per DIN 1048, 2. Bulk Density > 1150 kg/m3, 3. Crack sealing capacity upto 0.5mm

All systems to be installed as per manufacturer's recommendations, etc. complete with all lead and lift for all materials and labour and as directed by PM and giving guarantee for 10 years on Rs. 500/- Stamp paper in approved proforma.

4.5 Waterproofing on raft slab Sqm 19,249.00 0

Designing, providing, installing Membrane waterproofing system below RCC foundation / raft. System should create 100% water tight and chemical barrier around the structure. All complete to approval of PM and system shall be guaranteed for 10 years on approved stamp paper. System recommended and specified are as under.

Supplying and laying composite minimum 1.2mm thick, pre-applied, Fully bonded, pure HDPE membrane, over P.C.C. The HDPE membrane shall be fully bonded to the Raft bottom and shall consist of 3 layers - highly resilient HDPE film of minimum 0.9mm Thick, pressure sensitive adhesive and a granular protective layer. The membrane shall have minimum of 75mm side and end laps which shall be sealed with double sided tape. The membrane shall be loosely laid onto the PCC surface and shall be capable of receiving the structural steel & concrete directly over the membrane. The membrane shall be laid as per the manufacturer's specification and shall be turned up on the vertical surfaces upto 50mm depth from the top of the raft / foundation within the shutter of the raft / foundation sides to ensure no joint/overlap in the membrane at the corner, this shall include cleaning & removal of all the dust, dirt, oil, grease, cement laitance, loose particle & prepare the P.C.C. Substrate for laying of HDPE membrane, all as per manufacturer's instructions, etc, complete.

The membrane shall have minimum following properties: 1. Tensile Strength > 25 MPa as per ASTM D 412, 2. Elongation at Break > 500 % as per ASTM D 412, 3. Peel Adhesion to Concrete > 1500 N/m as per ASTM D903, 4. Puncture Resistance > 1000 N as per ASTM E 154, 5. Resistance to Hydrostatic Head > 70m as per ASTM D 5385, 6. Low Temperature Flexibility < (-)25 degC as per ASTM D1970, 7. Lap Peel Adhesion > 1500 N/m as per ASTM D1876, 8. Lateral Water Migration Resistance > 70m as per ASTM D5385.

All systems to be installed as per manufacturer's recommendations, etc. complete with all lead and lift for all materials and labour and as directed by PM and giving guarantee for 10 years on appropriate Stamp paper in approved proforma.

4.6 Waterproofing outside RCC walls - Vertical Sqm 5,472.00 0

Providing and laying 1.5 mm thick cross laminated SBS self adhesive waterproofing membrane based on based on a tropical grade of polymer modified bitumen laminated onto an impervious, non-perforated, cross laminated HDPE film. The compound membrane should exhibit tensile strength (L/T) > 3.5 N/mm2 (as per ASTM D 412-06), elongation (Longitudinal) > 300% & elongation (transverse) > 200% (as per ASTM D 412-06), puncture resistance > 280 N (as per ASTM E154), resistance to hydrostatic pressure head > 60m (as per DIN 1048), peel adhesion > 1.5 N/mm (as per ASTM D 1000). The system includes base preparation of cleaning, brushing and removal of flacky materials, construction joint treatment, proper coving between slab and wall junctions and priming the surface with cold applied bituminous primer followed by application of SBS membrane. The SBS membrane should be sealed properly at joints & maintaining 75 mm overlap between the membrane selvedge & 100 mm overlap on the end joints of the membrane over the surface etc as per manufacturers specification and methodology.

Termination: The SBS membrane should be terminated at top using aluminium strip flashing with fasteners and the joint should be sealed with polyurethane/hybrid polyurethane Sealant Construction Joint Trearment: All construction Joints in the retaining wall shall be opened in V-groove size to maximum depth of 15mm, clean the exposed area with air blowing machine and seal the joints with polymer modified mortar using Cement : Sand = 1 : 4 and SBR latex @ 2 kg per Bag of cement and level with the surface.

Protection to the waterproofing system against backfilling: Providing & Fixing of 8-10 mm thick dimple protection board, over the waterproofing membrane for vertical surface stuck to the membrane by spot bonding method, using synthetic adhesive with butt joints to protect the coating from damages from back-filling materials.

All systems to be installed as per manufacturer's recommendations, etc. complete with all lead and lift for all materials and labour and as directed by PM and giving guarantee for 10 years on Rs. 500/- Stamp paper in approved proforma.

4.7 Terrace Waterproofing with Insulation Sqm 8,761.00 0

Providing and applying spray applied, 2-component instant setting liquid hybrid polyurea based elastomeric waterproofing membrane by high-pressure spray application with heated two component spray proportioning equipment. The proportioning equipment must be capable of supplying correct pressure and heat for the appropriate hose length on a consistent basis. The hybrid polyurea coating system must meet the requirements of ASTM C836, having zero VOC, solids by volume 100% (as per ASTM D2369), tensile strength >12 MPa (as per ASTM D412), elongation > 450% 9as per ASTM D412 ), tear strength shall be minimum 50 KN/m 9as per ASTM D624), adhesion on concrete > 1.5 MPa (as per ASTM D 4541), shore A hardness not less than 85 (as per ASTM D2240), dynamic crack bridging ability with no crack observed in the coating after 20000 sinusoidal cycles (as per as per EN 1062-7 Method B- B3.2 of class B 3.2), abrasion resistance of not more than 60mg loss (1 Kg,CS 10 Wheels,1000 cycles - as per ASTM D4060), impact resistance > 10 N.m (as per ASTM D2794), resistance to hydrostatic pressure head of 7 Bar (as per ASTM D 5385), crack bridging ability of minimum 3.2mm (as per ASTM C1305), resistance to root (as per CEN TS/14416) and resistance to fire to as per EN 13501-1 Class B.

The coating shall be applied with a total consumption of 1.65 Kg/Sqm to achieve a total system DFT of 1.5mm, thereby satisfy the requirements of LAM as per ASTM C898 and shall be applied on the entire horizontal surface extending upto 300mm height on the vertical surface as per the manufacturers specification and methodology. Water pond testing shall be carried after membrane coating and shall be treated with approved epoxy grout treatment if any leakages found.

The system includes base preparation of cleaning, brushing and removal of flaky materials, thorough grinding, construction joint treatment, making angle fillets of 50mm x 50mm with polymer modified mortar at all the junctions followed by priming the surface with two component solvent free epoxy primer which is applied with a consumption of 200 grams per Sqm, followed by spray application of hybrid polyurea waterproofing coating.

Thermal Insulation PUF Layer over Waterproofing system: Spray applying 50mm thick CFC & HCFC free spray applied polyurethane foam satisfying the requirements of application as per IS 12423-Part3 which is applied in multiple passes with each spray pass of average 10-12mm thick. The spray applied polyurethane foam must have a free rise density of 33-35 kg/m³ and a spray density in the range of 45- 50 kg/m³(as per ASTM D1622), initial thermal conductivity of 0.023 W/m.k at 24°C (as per ASTM C518), tensile strength of >400kPa (as per ASTM D 1623), compressive strength greater than 300kPa (as per ASTM D-1621), closed cell content greater than 95% (as per IS 11239 Part5 ) , water absorption less than 1.5% (asper ASTM D2856), fire test property conforming to Class B2 as per DIN 4102 and Dimensional Stability of < 1.5% for 7 days when tested at -15& +70°C (as per ASTM D2126).

Supplying & laying 120 gsm Geotextile (non woven polyester) over the entire membrane maintaining proper overlaps.

Horizontal Protection & Slope Making Layer: Providing & laying of protective screed of M20 grade by keeping minimum 50mm thickness at drainage point with slope 1:100 containing 12 mm, 100% virgin polypropylene fibers @ 0.9 Kg/Cu.m with a broom finish, well compacted, curing for 7 days etc. complete. The screed shall be raised to the wall in the form of vatta to achieve a smooth corner. The screed shall be divided into panels of 2 mtr X 2 mtr with 6 mm wide x 10 mm deep construction joint and filling the same with polyurethane/polysulphide/hybrid sealant.

Vertical protection: Apply 1 coat of spatter dash bond coat mixed in the ratio of 1 part SBR latex: Cement and 2 parts of clean fine coarse sand and 1 part water to make thick slurry coat over the waterproof coating on the vertical walls upto 300mm height. Apply 12mm thick plaster over the prepared surface of cement sand mortar admixed with integral waterproofing compound conforming to IS 2645:2003 @ 220ml per bag of cement. Including finishing & water curing of plaster for minimum 7 days.

Treatment around pipe Core Cut Areas : All the pipes to placed / inserted in the core cut areas, shall be placed appropriately to be grouted around the cut bores. Roughening the pipe surface with hacksaw blade and applying a coat of SBR modified latex and sprinkling sand for proper adhesion. Grouting the gaps between the pipe and the core cutting by high strength non-shrink cementitious grout or micro-Concrete that shall be poured into the gaps after fixing in place an effective leak-free shuttering and support. Allow the grout to set for 24 hrs. and do the moist curing for 5 days. The area around the pipes (10mm) shall be filled with polyurethane/hybrid polyurethane sealant followed by flashing treatment with polyurethane waterproofing coating and specially coated 3-ply elastic corner Joint tape embedded between the two coats of waterproofing membrane.

All systems to be installed as per manufacturer's recommendations, etc. complete with all lead and lift for all materials and labour and as directed by PM and giving guarantee for 10 years on Rs. 100/- Stamp paper in approved proforma.

4.7 Waterproofing with 2K cementitious coating for Waterbodies, consisting of followings: Sqm 476.00 0

Bore Packing: For Over Flow Pipes Preparing the inside surface of core and PVC/ MS Pipe by roughening using suitable Sand paper to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Providing necessary formwork for packing the bore using suitable arrangement (depending upon site conditions).Applying a coat of styrene-butadiene based polymer coating using Nitobond SBR to enhance adhesion between the packing material and other surfaces. Packing the gap using non shrink cement polymer based grout using Conbextra GP2 upto the surface of the bore whilst the Nitobobd SBR is in tacky state.

Injection Grouting Providing Chemical injection treatment in the form of pressure grouting to the leakage points, cold joint by injecting cement slurry mixed with grout admixture Cebex 100 @ 225 gms per bag of cement, in the required consistency through the prefixed PVC/ Aluminium/ GI nozzles in the 18mm dia holes, fixing of nozzles with Renderoc Plug and final cutting the projected nozzles and sealing off the nozzles after the injection operation is over with Renderoc plug etc. as per manufacturers specification and as directed.

Coving/ Vatta Providing and application of 50-75mm vatta at the junction of slab and vertical walls with cement mortar (1:4) and admixed with SBR latex at dosage of 2.5 Ltr per 50kg cement and finishing the same as per EIC.

Waterproofing Coating Providing and carry out waterproofing treatment to Waterbodies etc.after proper surface preparation to remove loose dust,dirt etc.pre-dampening concrete surface, mixing and application of two coats of cementitious coating @ 2.5kg/ sqm at 1.5mm thickness using suitable brush or roller as per coverage etc. complete including all tools and tackles as per manufacturer’s specification.Cured material shall comply with ASTMD4060, ASTMD4541, ASTMD638, ASTMC836 and possess below properties: Mixed density: 1.68g/cc, Elongation >150%, Adhesion to concrete ->1N/mm2, Non-toxic,Static crack accommodation-1 mm

Providing and laying protective screed of average 50mm thickness admixed with Integral Waterproofing liquid admixture ata dosage of 150 ml per 50 kg cement.

Providing and applying plaster of average 15-20mm thickness admixed with Integral Waterproofing liquid admixture at a dosage of 150 ml per 50 kg cement.

TOTAL OF WATERPROOFING WORK 0

5. FLOORING WORK

The rates quoted by the Contractor for items under this head shall be inclusive of the following :

a) All flooring to be protected by approved suitable floor protection system of closed cell, polymer based micro cellular foam, reinforced with high performance polymers sheet during construction. Flooring to be covered over in finished condition and after uncovering to be delivered in a finished condition free of scratches, lines and any other deformities etc.

b) All the flooring, dado & cladding shall be fixed using approved quality cement based high polymermodified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness or more as required.

c) The contractor shall procure mortar, adhesive, grout etc. of approved quality design and standard and he will not change source of supply without written permission from PM and with revised samples being approved.

d) Contractor shall prepare and install mockups for floor and wall as per drawings. Mockups may be part of completed work if undistributed. Nothing extra shall be paid on this account.

e) Joint patterns to be followed. No extra cuts for variable joint patterns, shall be paid for wastage.

f) Skirtings to have profiled edges as per PM's instructions. No extra cost to be paid for plaster chipping, required to adjust skirtings levels. However, cost of mouldings to be indicated separately, so as to deduct cost towards the same, incase profiling is avoided.

g) All necessary cut outs in walls, clearing up plaster towards work required for services, not to be paid for separately, even if it is conducted subsequent to work completion. No extra for cutting, edge finishing required for junction boxes of electrical works, etc.

h) Bedding shall be done in grey cement & white cement slurry to be used for laying marble.

i) Stone to be coated with invisible, penetrating sealer which forms an invisible water repellent coating (Laticrete 190 sealer or equivalent approved) on all (Six) sides as per manufacturer recommendations

j) All the stone cladding shall be protected by using clear coat of nano technology based impregnating sealer (Maxi Seal of Laticrete or equivalent approved) designed for the protection of all medium to dense porous tile/stone and grout surfaces. The rate of items shall include the same and no extra shall be paid towards the same.

k) Grouts in flooring i) All interior flooring to have 3 mm wide Cement Sanded grout- L-500 (Laticrete). ii) All interior and exterior Cladding to have 5 mm wide sanded Grout- L 500 (Laticrete) iii) All toilet wall dados to have 3 mm wide Laticrete epoxy grout SP-100 (Laticrete) iv) All exterior flooring to have L 500 -5 mm wide sanded grout (Laticrete)

l) The quoted rate shall include the cost of all materials and labour involved in all the operations as specified above and to execute the work as per approved drawings including staging / scaffolding etc. necessary for execution of the respective item for all height and for all floor levels. Item measurable in sqm.

Drawing no- A12-04 Det -1/A14-01

5.1 Providing and fixing 20 mm thick gang saw cut, mirror polished, Premoulded and prepolished, machine cut for kitchen platforms, vanity counters, coping, tread, landscaping, window sills, facias, parapet top and similar locations of required size, approved shade, colour and texture laid over using approved adhesive over cement concrete screed (paid separately), joints grouted with approved matching colour grout epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels, as per sample approved by Engineer in-charge. Necessary MS/ SS frame structure for fixing the stone counter shall be paid in relevant tender item.

Honed Granite of any colour and shade

Area of slab over 0.50 sqm

5.1.1 a) Honed Granite stone slab (Basic Rate: Rs. 200/- per Sqft without GST) Sqm 289.00 0

5.2 Extra for fixing marble/ granite stone over and above corresponding in facia and drops of width upto 200mm with epoxy resin based adhesive including cleaning etc complete. Facia shall be match with shade of counter or platform. Rmt 91.00 0

5.3 Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/ Granite/ stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete. Nos 82.00 0

5.4 Providing and fixing stone slab with table rubbed, edges rounded and both side polished, of size 450 x 900 mm deep and 40 mm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

5.4.1 Granite Stone of approved shade (Basic Rate: Rs. 350/- per Sqft without GST) Refer A12-04 Det -1/A14-01 Sqm 14.00 0

5.5 Providing and fixing premoulded and prefinished, machine cut stone for coping, parapet top and similar locations of required size, approved shade, colour and texture laid using approved adhesive over cement concrete screed (paid separately), joints grouted with approved matching coulour grout, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels, as per sample approved by Engineer in-charge.

5.5.1 50 mm thick Sand stone of rough finish and colour and shade as per selection, (Basic rate of stone -Rs-400/- per Sqft without GST) Refer A12-08 Det - 1,2,3,4,6 Sqm 1,178.00 0

5.6 Providing and laying Stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 25 mm thick stone slab using approved adhesive over cement concrete screed (paid separately), joints grouted with approved matching colour grout, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

5.6.1 Honed finish Steel grey Granite stone slab of 300mm x 300mm (Basic rate of stone -Rs-213/- per Sqft without GST) Refer A12-04 Det -1/A14-01 Sqm 763.00 0

5.6.2 Polished Grey Granite stone slab of 600mm x 600mm (Basic rate of stone -Rs-232/- per Sqft without GST) Refer A12-04 Det -1/A14-01 Sqm 234.00 0

5.6.3 Honed finish Mandana-1 stone slab of 900mm x 900mm (Basic rate of stone -Rs-448/- per Sqft without GST) Refer A12-04 Det -1/A14-01 Sqm 5,268.00 0

5.6.3 Honed finish Mandana-2 stone slab of 900mm x 900mm (Basic rate of stone -Rs-448/- per Sqft without GST) Refer A12-04 Det -1/A14-01 Sqm 540.00 0

5.7 Providing and laying Stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 35 mm thick stone slab using approved adhesive over cement concrete screed (paid separately), joints grouted with approved matching colour grout, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

5.7.1 Honed finish Sand stone slab of 300mm x 300mm (Basic rate of stone -Rs-377/- per Sqft without GST) Refer A12-04 Det -1/A14-01 Sqm 67.00 0

5.8 Providing and laying polished Kota stone slab 600mm x 600mm flooring using approved adhesive over cement concrete screed (paid separately), joints grouted with approved matching coulour grout, including rubbing and polishing etc. complete. (A) 25mm thick Refer A12-04 Det -4/A14-01 Sqm 7,619.00 0

5.9 Providing and fixing 25mm thick approved up to 300mm wide Kota stone treads in 3 peices to full length of step and machine cut, machine polished. Treads to be rounded at front and all exposed edges machine polished. Further treads to have edge polished chamfering with 3 nos. (6mm x 3mm deep) grooves on top at front or as detailed in drawing for antiskid effect as shown in the drawing. Treads fix to be using approved adhesive over cement concrete screed (paid separately), joints grouted with approved matching coulour grout,, curing, cleaning, polishing etc. all complete at all heights and leads to the approval of the Engineer in charge. (Basic rate of stone -Rs-113/- per Sqft) Refer A12-04 Det -4/A14-01 Sqm 633.00 0

5.10 Providing and fixing 25mm thick and about 150mm high approved Kota stone risers, skirting machine cut and machine polished in 3 piece or as directed, to full length of step, stone fixed by approved adhesive on back, to correct line, level and plumb. Joints are well cleaned grouted with matching colour approved readymade grout, curing, polishing, cleaned and where specified or shown in drawing exposed edge of stone rounded / chamfered and polished, skirting to be match with wall cladding/ flooring pattern all complete to the satisfaction of the Engineer in charge. (Basic rate of stone -Rs-113/- per Sqft without GST) Refer A12-04 Det -4/A14-01 Sqm 360.00 0

5.11 Providing and fixing 25mm thick approved up to 300mm wide Mandana stone treads in 3 peices to full length of step and machine cut, machine polished. Treads to be rounded at front and all exposed edges machine polished. Further treads to have edge polished chamfering with 3 nos. (6mm x 3mm deep) grooves on top at front or as detailed in drawing for antiskid effect as shown in the drawing. Treads fix to be using approved adhesive over cement concrete screed (paid separately), joints grouted with approved matching coulour grout,, curing, cleaning, polishing etc. all complete at all heights and leads to the approval of the Engineer in charge. (Basic rate of stone -Rs-448/- per Sqft without GST) Refer A12-04 Det -1/A14-01 Sqm 60.00 0

5.11.1 -Do as per above item 5.11 but for 450mm wide Mandana stone treads as shown in drawing Refer A12-04 Det -1/A14-01 Sqm 32.00 0

5.12 Providing and fixing 25mm thick and about 150mm high approved Mandana stone risers, skirting machine cut and machine polished in 3 piece or as directed, to full length of step, stone fixed by approved adhesive on back, to correct line, level and plumb. Joints are well cleaned grouted with matching colour approved readymade grout, curing, polishing, cleaned and where specified or shown in drawing exposed edge of stone rounded / chamfered and polished, skirting to be match with wall cladding/ flooring pattern all complete to the satisfaction of the Engineer in charge. (Basic rate of stone -Rs-448/- per Sqft without GST) Refer A12-04 Det -1/A14-01 Sqm 32.00 0

5.13 P & L 12" x 12" vitrified 10 mm thick tile flooring on new surface or fixing on existing flooring by using approved adhesive over cement concrete screed (paid separately), joints grouted with approved matching coulour grout, including dismentaling of existing flooring and jointed with color cement slurry including finised with flush pointing & cleaning the surface etc. complete for antiskit (Basic rate of tile-Rs-150/- per Sqft without GST) Refer A12-04 Det -7/A14-01 Sqm 174.00 0

5.14 Providing, fabricating and laying recessed electro-forged SS304 walk-off grating mat brushed finish made out of stainless steel 304 angle frame and hardware (Balco or equivalent), ADA compliant, slip resistant, custom size as shown in plans fixed on cement concrete bed (concrete bed measured & paid sepretley) with recess to lay mat of overall 100mm thick floor. All the work to be protected till handing over the project & to the approval of EIC. Refer-A12-04 & 8/A14-01 Sqm 77.00 0

5.14.1 -Do as above item no-5.14 but for G.I walk off bar grating mat Refer- DET 8A / A14-01, A12-04 Sqm 38.00 0

5.15 Providing and laying 9mm thick approved make tufted multi-level loop pile scroll Carpet tile flooring (500mm x 500mm) as per detailed and instruction of approved manufacturer etc. Carpet flooring shall be fixed over exisiting marble mosaic flooring with as adhesive as recommended by the approved of carpet manufacturer. Required edging angles, junction, entrances etc. shall be fixed and finished with as per recommendation of the carpet manufacturer to approval of the Engineer in charge / Architect. Sub-base floor to be leveled, cleaned all complete at all heights and leads to the entire satisfaction of the Engineer in charge. (Basic rate of tile-Rs-220/- per Sqft without GST) Refer A12-04 & Det -10/A14-01 Sqm 682.00 0

5.16 Providing and laying C.C. pavement of mix M-30 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator, vaccum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. Refer A12-04 & 2/A14-01 Cum 628.00 0

5.17 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vaccum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).Refer A12-04 & 13/A14-01 Cum 39.00 0

5.18 Providing and fixing of 100mm high 25mm thick 1st quality Teak Wood skirting with SS screws, adhesive etc. all complete Refer -A12-06 & 3/A14-03 Rmt 420.00 0

5.19 Providing and installing 20mm thick approved 1st quality Teak wood plank flooring of approved make with tongue and groove joint system as shown in drawings and instruction of approved manufacturer / PM of approved shade; fixed over 12mm thick approved marine ply surface fixed over existing IPS. Ply shall be chemically treated, seasoned and anti-termite treated including cleaning, treating base concrete screed, treating ply with a thin coat of polyurethane prior to being screwed down to concrete floors prior to fixing and making groove/joint around edges as specified in drawing and by the manufacturer etc. all as detailed in technical specification, drawings and that of approved flooring manufacturer etc. to entire satisfaction of the PM. (Refer drawings No.A12-04 & 05/A14-01) Sqm 785.00 0

5.20 Providing and fixing Wooden deck (25 mm wooden planking, tongued and grooved 2nd quality teak wood planking / flooring including PU polish on GI frame and supports as shown in the drawing. Rate shall include preparing and submitting shop drawings with all fixing details prior to fabrication and execution etc. all complete as shown in the drawing and directed by Engineer in chrage. ('GI frame and support as shown in the drawing to be paid for seperatly) Drg Refer -A12-04 & 12/A14-01 Sqm 127.00 0

5.21 Providing and fabricating GI frame work for above item as per variable height with concrete pedestal as per drawings No.A14-01-Detail-12 (Note: Concrete to be paid for seperatly) Kg 5,715.00 0

5.22 Providing and laying 10mm thick Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 154 77, including grouting of joints. Drg Refer -Det-07/A14-01

5.22.1 Size of Tile 600x600 mm including epoxy grouting of joints Sqm 4,514.00 0

5.23 Providing and laying polished kota stone slab 25mm thick in risers of steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray cement slury mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. Drg Refer -Det-14 & A7-22 Sqm 516.00 0

5.24 Supply and installation of Rubber Tile Flooring, skirting having thickness of 5mm. This product is installed on floor base with adhesive. Sqm 26.00 0

Rubber tile of 5mm is made up of 85% black rubber granules and 15% synthetic EPDM granules. Rich colors, Environmental friendly, non-toxic, Recycled, non-pollution, Moderate and adjusted hardness, Excellent resilience, wear well, soft, anti-slip, anti-fatigue, Density (kg/m3):1000/1200, Hardness (Shore a):68, Stretch (MPA):2.2, Abrasion resistance:0.0075g (ASTM-D4060-01), Rebound resistance:55%, Friction coefficient: trends μs:0.995 trends μk:0.930, Shape deformation:42%, Thickness: 5mm ±0.3mm. etc. all complete as per detail drawing or as per instruction of Engineer in charge. Refer CODE-A12-04 & 3/A14-01

5.25 Providing and installing all weather 35mm thick Stone Deck Tile 600mm x 600mm size flooring with ABS plastic mesh and interlocking system, tiles made from travertine stone anti-skid rough finish fixed over waterproofing finished with leveled IPS, all complete to the entire satisfaction of the EIC. Refer A12-04 & 14/A14-01 Sqm 27.00 0

5.26 Providing and fixing dry cladding with 35mm thick gang saw cut stone with machine cut edges of uniform colour and size as per drawing, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. Item to include Providing and fixing adjustable stainless steel (grade 316) cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge.

5.26.1 Sand stone - 35mm thick gang saw cut stone with 5mm wide joint filled approved PU grout (Basic rate of stone -Rs-377/- per Sqft without GST) - 125mm away from the internal wall Refer A12-05 & 6/A14-02 Sqm 4,853.00 0

5.26.2 35mm thick satin finish Mandana stone cladding filled approved PU grout (Basic rate of stone -Rs-392/- per Sqft without GST) - 125mm away from the internal wall Refer A12-05 & 6/A14-02 Sqm 2,254.00 0

5.26.3 35mm thick mirror finish Granite stone cladding filled approved PU grout (Basic rate of stone (Basic rate of stone -Rs-419/- per Sqft without GST) - 125mm away from the internal wall Refer A12-05 & 6/A14-02 Sqm 1,002.00 0

5.26.4 -Do- as above 5.26 but 35mm thick last stone at lintel filled approved PU grout (Basic rate of stone (Location : Interior) (Basic rate of stone -Rs-338/- per Sqft without GST) Drawing no- A11-04- Detail-3 & 4 Sqm 313.00 0

5.26.5 -Do- as above 5.26.1.1 but 250mm away from the external wall Refer A11-01 Det - 02 Sqm 70.00 0

5.29 Providing and fixing machine cut, composite patterned wall wet cladding out of 25mm thick flamed finish Granite stone machine cut, machine polished to walls and columns. Stone fixed with required stainless steel pins / dowels / cramps including drilling holes, making notches etc. for securedly fixing with pins / cramps to wall. Stone fixed in position with approved readymix ploymer based adhesive in line and level and in pattern as shown in the drawing. Joints cleaned, grouted with approved ready made ploymer modified PU grout or cured and cleaned, further to include required double legged independent scaffolding etc. complete to the satisfaction of the EIC. (Basic Rate of stone: Rs. 315/- per Sqft without GST) Refer DWG. A14-02 DET 5 Sqm 13.00 0

5.30 Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-coarse sand : 4-graded stone aggregate 20mm nominal size) laid in one layer and finished with a floating coat of neat cement. (The Contractor will provide for preparation or surface by cleaning, hacking and exposing aggregate to achieve the best bond, and any curling, lifting or debonding noticed shall be rectified by the contractor at his cost), protection, etc. complete to the entire satisfaction of the EIC. Cum 1,640.71 0

5.31 Providing and laying self leveling mortar using very low emission, polymer modified cementitious floor levelling compound which provides a smooth finish on subfloors before the application of resilient flooring. Sqm 946.00 0

5.32 RAISED ACCESS FLOOR SYSTEM

Providing and fixing removable raised/ false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by PM consisting of a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug.

b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange).

5.33 i) About 300mm Finished Floor Height (FFH) with approved Vinyl flooring on tile flooring Refer A12-04 & 9/A14-01 Sqm 190.00 0

5.34 Providing and cladding with 1.2 mm thick Grade 304 grade Stainless Steel sheet, scratch resistant, in panel sizes as per approved design, confirming to relevant standards with all mechanical fixtures as per approved drawings and design, moulding of edges, buffing of surface, flushing of joints, silicon sealants, etc. all complete as per direction of Engineer In charge. MS Frame work & ply base shall be paid separately Refer A14-03 /Det-14 Sqm 69.00 0

5.35 Providing, fabricating and fixing circular column cladding using 1.2 mm thick Stainless Steel sheet of Grade 304, scratch-resistant finish, formed in curved panels (259mm) to required radius and panel sizes as per approved shop drawings. The work shall include bending, rolling, edge moulding, buffing/polishing to achieve uniform finish, and making flush joints with minimal visible gaps. The cladding shall be fixed over a prepared framework consisting of 50 x 25 mm GI sub-structure anchored to existing MS column (600Ø) using suitable fasteners, along with 6 mm thick flexi-ply (in multiple layers as required) to achieve the desired curvature. Stainless steel sheets shall be fixed using approved Z-clips, mechanical fasteners, and necessary supports ensuring proper alignment, rigidity, and true curvature.The item shall include provision of backing support, fixing accessories, stainless steel screws, spacers, silicon sealant at joints, finishing of edges, necessary cut-outs, and coordination with other services. All work shall be executed as per approved drawings, specifications, and instructions of the Engineer-in-Charge to achieve complete and seamless finish. Sqm 184.00 0

5.36 Providing and fixing 100 mm high Stainless steel sheet skirting made out of 1.2mm thick Stainless steel sheet SS304 moulded to profile inc sections fixed over 12mm thick marine ply using epoxy adhesives, fixing with screws, teakwood beading etc.),polishing etc , cutting, bending, curing etc all complete. (Drawing no- A12-06 & 4/A14-03 Rmt 12.00 0

5.37 Providing and laying loose gravel finish over terrace/roof surface, comprising supply of clean, hard, durable, and well-graded natural gravel of approved quality and size (20–40 mm or as specified), free from dust, dirt, and organic impurities.The work shall include thorough preparation of the surface, ensuring that the underlying waterproofing treatment/screed is complete, properly cured, and protected. Gravel shall be spread uniformly over the surface to a required thickness of 40–50 mm (or as directed), carefully leveled and dressed to achieve an even and consistent layer.The gravel layer shall be laid in a manner that ensures proper drainage, avoids displacement, and does not damage the underlying waterproofing system. The item shall include necessary edge retaining arrangements (if required), handling, loading/unloading, transportation, stacking, and all labour, tools, and tackles required for proper execution. All work shall be carried out strictly in accordance with approved drawings, technical specifications, and as directed by the Engineer-in-Charge, ensuring complete coverage and satisfactory performance. Sqm 5,280.00 0

TOTAL OF FLOORING WORK 0

a) All Plywood samples to be approved before procurement.

b) All exposed plywood to have approved wood lipping & stain to match.

c) All wood to be well seasoned.

d) All surfaces of wood to have antitermite treatment and anti-soligium paint, at multiple stages of the job. Agency appointed to be approved by PM.

e) All Plywood shall be Commercial plywood and to be as per specified List of Suppliers given.

f) All grooves of all thickness, inlay pattis in partitions and panellings to be included in quotations and no extra cost to be paid for the same.

g) Grooves to be provided at intersection of all separate surfaces such as wooden skirting and gypsum board. Cost of the same to be included in cost of skirting. Grooves also between carpentry items and civil items to be provided.

h) Paneling to be paid for only upto bottom of false ceiling. All necessary frame work required for anchoring partition above into slab above false ceiling to be included in cost of items.

i) Grooves to be provided at junction of partition, paneling 8mm to 10mm as required for carpet to slide in. No extra cost to be paid for the same.

j) All hardware to be in SS hairline/satin finish unless specified otherwise.

k) All extra frame work required within partitions and paneling for supporting of A.C.grills, fixing of skirting etc.and all such allied services.to be included in the cost of partitions.

l) Skirting in Plywood with finishing material on carpentry items to be included in the cost of carpentry items.

m) Wooden skirting over brick, concrete blocks or columns or partitions with gypsum board only to be paid for separately.

n) Drawings indicate only tentative locations and quantity of grooves, inlay pattis etc. Actual execution as per instructions of PM.

o) Bands upto 150mm thickness not to be paid for separately. Only in cases where width exceeding 150mm has to be fully put over existing paneling/partition/doors in order to create fully raised levels with complete grooves, wherever required.No extra cost shall be paid towards additional labour, hardware, adhesives etc. required to create the raised panel.

p) All wooden frames to form edgings wherever door openings occur. Cost of doors to include cost of frames wherever a part of carpentry items. Door frames to be paid for separately only wherever interface with civil work.

q) Additional bands in plywood, making niches, dub panels not to be charged for separately.

r) Nail free assembly of all types of fabric on paneling to be ensured.

s) No extra rate for height shall be paid

t) Rate. Quoted rate shall include the cost of all materials and labour involved in all the operations as specified above and to execute the work as per approved drawings including staging / scaffolding etc. necessary for execution of the respective item for all height and for all floor levels. Item measurable in sqm.

Rate shall be included :-

a) All materials with wastage, accessories, labour etc.

b) Approved wooden / Aluminium frame work.

c) Stainless steel fittings, fixtures, fasteners

d) Refer door schedule drawing no-A-13-15 & 16 for type of finishes on particular door.

6.1 Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.

6.1.1 About 100mm overall thickness partition with 12mm thick marine grade Plywood conforming to IS 710 on both sides, further cladded with 12.5mm thick tapered edged plain Gypsum plaster board on both sides side as shown in the drawing. (Refer Drg No. Det-2/A13-08) Sqm 189.00 0

6.1.2 About 100mm overall thickness partition with 12mm thick marine grade Plywood conforming to IS 710 on both sides, further cladded with 12.5mm thick tapered edged plain Gypsum plaster board on both sides side & 50mm insulation as shown in the drawing. (Refer Drg No.A13-08-Detail-3) Sqm 51.00 0

6.1.3 About 400mm overall thickness partition with 19mm thick marine grade Plywood conforming to IS 710 on both sides, (fixed to MS structural column & beamframing-paid separetly) further cladded with 15mm thick oak wooden cladding on planks as approved both side as shown in the drawing. Reuired sub framing to be included in the cost. (Refer Drg No.A13-08-Detail-4) Sqm 452.00 0

6.1.4 Providing and fixing dry partition for elliptical ramp of about 300 mm overall thickness, consisting of 12 mm thick gypsum board and 18 mm thick marine grade plywood conforming to IS 710 fixed over MS sub-framing attached to structural columns and beams (structural steel work to be paid separately), including providing and fixing all necessary secondary framing members, cleats, screws, fasteners and accessories complete. The partition shall be suitable to receive stone cladding finish as per architectural drawings, including cutting, fitting, making openings, finishing and making good complete, all as per approved drawings, specifications and direction of Engineer-in-Charge. (Refer Drg. No. A13-08-Detail-5). Sqm 217.35 0

6.2 Overall 125mm wide Panelling with 12mm thick marine grade Plywood and 12.5mm thick approved Fire rated Gypsum board as shown in drawings with provision for light fixtures. Refer A12-05 REF : 17/A14-02 Sqm 8,267.00 0

6.3 Overall 125mm wide Panelling with 12mm thick marine grade Plywood and 15mm thick approved teak wood panel as shown in drawings with provision for light fixtures. Refer A12-05 REF : 7/A14-02 Sqm 1,545.00 0

6.4 Providing and fixing panelling with 8mm thick approved flexiply on existing column of 600mm dia. And finish with 6mm thick approved veneer as shown in drawing. REF: 15/A14-03 Sqm 48.00 0

6.5 Providing and fixing Roller blinds (UP-01) (75% black out, made out of 70% PVC, 30% Polyester) of approved make as per the manufacturer's specifications with drive unit, end plug, support brackets, roller tube, bottom rail, ball chains etc. Drive unit to be of moulded plastic with straight rectangular support pin and inserted into the tube end. It shall be driven by a ball chain pulley. End plug shall be moulded to plastic locking pin. The plug shall be inserted into the tube end. Support brackets shall be of zinc plated steel and provided with moulded plastic covers and used in right or left hand positions differentiated by acceptance of the rectangular drive unit support or the round idler plug pin. Roller tube shall be made out of roll formed steel of thick. Suitably protected against corrosion, and keyway integral with the tube to accommodate the spline. Bottom rail shall be a stiffening element inserted into a bottom rod pocket. Tube to be of the material as approved out of timber, PVC, steel or VB bottom rail. Ball chain shall be 2mm diameter cord with acetyl balls moulded co-axially to it on 6mm pitch to form ball chain. Refer A12-14 Sqm 681.00 0

6.6 Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 120 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer in- Charge. (for sound attenuation of mechanical spaces)

6.6.1 On Wall / Panelling Surface Refer-A12-05 REF : 11/A14-02 Sqm 4,556.00 0

6.6.1 On Ceiling Surface Refer-A12-07 & 8/A14-04 Sqm 2,249.00 0

6.7 Designing, providing and fixing wooden louvers as detailed in drawing (A14-05), including making shop drawings to show the fixing arrangment of louvers to back side slanted paneling using GI Z clips, GI framing in back paneling to take the load of the louvers and securing the same to back side wall / floor and adjusting the same as per site conditions, shop drawings including mock up to be approved by the Architect & PMC prior to execution. The item comprising of:

6.7 Providing and fixing partition / panelling upto ceiling height consisting of G.I. framework and approved quality plywood backing with finish paneling, including providing and fixing framework made out of G.I. framing system as required, securely anchored to floor, wall and ceiling with suitable dash fasteners, anchor fasteners, screws and plugs complete. The work shall include providing and fixing 19 mm thick plywood substrate fixed over the G.I. framework with suitable screws, and further providing and fixing 12 mm thick teak wood finished panel with clear polish/ clear finish as approved, fixed over plywood backing with approved adhesive/ screws complete. The item shall include necessary cutting, grooves, edge finishing, making openings for services, providing backing supports, alignment, levelling and all accessories required for complete installation. All joints shall be properly finished flush to surface, including necessary sanding, filling, polishing/ clear coating and finishing as per approved drawings and direction of Engineer-in-Charge, complete in all respects. (Refer-A14-05) Sqm 85.00 0

6.8 Providing and fixing wooden louvers approximately 250 mm wide x 60mm thick as per approved drawing and design, comprising 12 mm thick teak finish wooden panels fixed on both sides over stainless steel square tube framework made out of 35 x 35 x 3.2 mm SS sections, complete with internal supports, Further to fix solid teak wood edging with clear polish finish, necessary anchors, fasteners, welding, cutting, grinding, anti-termite treatment and fixing arrangement. The work shall include fabrication of SS framework, provision for alignment, edge finishing, joint treatment, all hardware and accessories, complete in all respects as directed by the Architect/Engineer-in-charge. Measurements shall be taken in running metres of finished surface area. (Refer-A14-05) Rmt 329.00 0

6.9 Providing and fixing Wooden door with approved 1st quality teak wood door frame of size 45mm x 150mm size, fixed with holdfasts / dash fasteners / SS screws, frame to be finished with PU polish in approved shade to the exposed faces, the frame face in contact with masonry shall be applied with black japan paint. The shutter shall be factory made 45mm thick flush shutter of approved make confirming to IS 2202 (Part - I); Shutter shall be manufactured with exterior quality synthetic adhesive forming marine ply surfaces, internally lipped. Further shutter shall be finished with 4mm thick veneer finish including PU polish on both side of approved make, shade and design, hot pressed at factory, edges of shutter shall be provided with 6mm thick teakwood beadings using exterior quality synthetic adhesive, headless GI nails, screws, beading finished with PU polish, etc. Also including creating pattern / design of paneled shutter as shown in the drawing. Further providing and fixing ironmongeries as per schedule and drawings all complete to entire satisfaction of the PM. (Refer Door Schedule: A13-15,16)

6.9.1 Door D-B-G-01 (First Aid) overall size 900mm x 2400mm. with approved 4mm thick veneer finished. Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs and key opening

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Door stopper

e) Lever Handle

6.10 Providing and fixing Wooden door with approved 1st quality teak wood door frame of size 75mm x 250mm size, fixed with holdfasts / dash fasteners / SS screws, frame to be finished with PU polish in approved shade to the exposed faces, the frame face in contact with masonry shall be applied with black japan paint. The shutter shall be factory made 76mm thick insulated flush shutter of approved make confirming to IS 2202 (Part - I); Shutter shall be manufactured with exterior quality synthetic adhesive forming marine ply surfaces, internally lipped. Further shutter shall be finished with 4mm thick veneer finish including PU polish on both side of approved make, shade and design, hot pressed at factory, edges of shutter shall be provided with 6mm thick teakwood beadings using exterior quality synthetic adhesive, headless GI nails, screws, beading finished with PU polish, etc. Further providing and fixing ironmongeries as per schedule and drawings all complete to entire satisfaction of the PM. (Refer Door Schedule: A13-15,16)

6.10.1 Gallery Door (Type-4) D-A-G-03 (Orientation Gallery) & D-A-G-13 (Auditrium Exit), overall size 1800mm x 2400mm Nos 2.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Narrow profile Mortise Dead lock, 35 BS/8mm, SSS finish with cyl, escutheion suitable for double leaf door

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

6.10.2 Gallery Door (Type-3) D-F-G-02 (Temp. Gal), D-G-L-05, D-G-L-06 (Location : Utsah Gal-Entry, Exit) overall size 3000mm x 3600mm, out of which 1800mm wide x 2400mm high openable double leaf door, with approved 4mm thick veneer finished. Nos 3.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Motorised locking system

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Door stopper

e) Pull/Push handle

6.11 Providing and fixing Wooden partly fixed, partly openable, partly galzed door with approved 1st quality teak wood door frame of size 75mm x 250mm size, fixed with holdfasts / dash fasteners / SS screws, frame to be finished with PU polish in approved shade to the exposed faces, the frame face in contact with masonry shall be applied with black japan paint. The shutter along with top fixed portion above shutter shall be factory made 76mm thick insulated flush shutter (with marine grade plywood 19mm thick on both sides and rock wool insulation inside) of approved make; Shutter shall be manufactured with exterior quality synthetic adhesive forming marine ply surfaces, internally lipped. Further shutter shall be finished with 4mm thick veneer finish including PU polish on both side of approved make, shade and design, hot pressed at factory, edges of shutter shall be provided with 6mm thick teakwood beadings using exterior quality synthetic adhesive, headless GI nails, screws, beading finished with PU polish, etc. The side fixed glazed panels shall be as per the drawing. Further providing and fixing ironmongeries as per schedule and drawings all complete to entire satisfaction of the PM. (Refer Door Schedule: A13-15,16)

6.11.1 Door (Type-3) D-A-1F-02 (Gaurav Gallery) overall size 3000mm x 3600mm. Double leaf openable wooden shutters of size 1800mm x 2400mm and top fixed portion with approved 4mm thick veneer finished in PU polish, both side portions with fixed glass (#3: Insulated (10mm + 16mm air gap + 8mm) 34mm thick DGU Nos 1.00 0

a) SS Floor springs

b) Narrow profile Mortise Dead lock, 35 BS/8mm, SSS finish with cyl, escutheion suitable for double leaf door

c) Pivots at top

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Wooden handle made out of MS Tee section, 1800mm long - 2 x 2 Nos.

6.11.2 Door (Type-3A) D-B-G-02 (Multipurpose) overall size 2100mm x 2400mm. Double leaf openable shutters of size 1050mm x 2400mm, side portion fixed with glass (#3: Insulated (10mm + 16mm air gap + 8mm) 34mm thick DGU, and top portion fixed 75mm thick with approved 4mm thick veneer finished. Nos 1.00 0

a) SS Floor springs

b) Narrow profile Mortise Dead lock, 35 BS/8mm, SSS finish with cyl, escutheion suitable for double leaf door

c) Pivots at top

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Wooden handle made out of MS Tee section, 1800mm long - 2 x 2 Nos.

6.12 Providing and fixing of following fully glazed door shutters out of 50mm thick x 100mm wide top, bottom rail and vertical style of 1st quality teakwood, kiln seasoned, antitermite treated, shaped, grooved rebated with required mating styles, joined with tongue and grooved mitered joints arrangement including use of approved water repellent exterior quality adhesive, SS Screws, pins, etc. Also to include two coats of wood primer, two under coats and one finished coat of synthetic enamel paint matt/gloss finish. Also to include 8mm thick toughened glass as detailed, required ironmongery shall be of best quality heavy duty Stainless steel as detailed for each shutters here under.

6.12.1 Door (Type-6) D-B-2F-01, 02, 03, 04, 06, 10, 14, 15, 18, 19, 20, 21, 22, 23, 24 (Location: SNR Admin, Meeting room, Director, Pantry, Documents lounge, File room, Accounts, BLD Management, Curatorial) Single leaf glass doors with overall size of 800mm x 2100mm height, with wooden frame and glass type #5 Insulated (6mm + 12mm + 5mm) 23mm glass with hinges, lever type handles, floor spring and door stopper, eye stop sticker as detailed in drawings. Nos 15.00 0

6.12.2 Door (Type-6) D-B-2F-07, D-B-2F-16 (Location : Reception, Conference) Single leaf glass doors with overall size of 1200mm x 2100mm height, with wooden frame and glass type #5 Insulated (6mm + 12mm + 5mm) 23mm with hinges, lever type handles, floor spring and door stopper, eye stop sticker as detailed in drawings. Nos 2.00 0

6.12.3 Door (Type-6) D-C-G-10 (Location : Restaurant counter) Single leaf glass doors with overall size of 750mm x 2100mm height, with wooden frame and glass type #7 Single pane 8mm thick glass with hinges, lever type handles, floor spring and door stopper as detailed in drawings. Nos 1.00 0

6.13 Providing and fixing toilet cubical systems of approved make and manufactured in standard dimensions of 600mm ± 10mm width door size with 12mm thick solid Compact Laminate panels made of KRAFT paper impregnated with Phenolic resins under high pressure and temperature, including doors, pilasters & intermediate panels, which should be resistant to heat, bacteria, water, chemical, scratch and impact. Finished product should be as per approved texture, shade & drawing, detailing and developed according to IS-2046 and BS-476/97 standards. The toilet cubicle setup shall include necessary hardware fittings, made out of stainless steel (Grade-304), as per manufacturer’s specifications and approved by Engineer-in-charge.

Hardware fittings should consist of (1) Stainless steel Adjustable foot/ pedestal of SS 316 grade to give 150mm clearance from bottom and of weight not less than 600grams (2) Stainless steel U-channels of 20 gauge and 12 x 20mm size (3) Stainless steel Top rail pipe (OD:24mm of 18 gauge) with corner connectors

(4) Stainless Steel Head Rail Tubular Holder (5) Stainless steel Gravity hinges (3 nos.) not less than 75mm length and weight not less than 210 grams of weight not less than 200 grams. (6) Stainless steel Coat hook with nylon door stopper (7) Stainless steel Door knob (8) Stainless steel Baby latch (9) Wall bracket SS 304 (10) Corner Connector (11) Rubber noise deafening tape (12) Stainless steel 304 Screws and PVC wall plugs.

The top fitting arrangement shall comprise of stainless steel (round) top rail, fixed to pilasters and stainless steel tubular holder. Stainless steel wall fixing roses shall be used on the wall to hold the top rail. In absence of brick walls, stainless steel corner bends (connected to the top rail) shall be used on the corners of the cubicle. All screws should be of stainless steel (Grade-304). All pilasters shall be supported by stainless steel adjustable foot. The base of the stainless steel bottom cladding shall be anchored to the floor with a clearance height of 150mm.The intermediate panel shall be of one continuous panel without any joint. All visible edges shall be chamfered.

6.13.1 a) L-Shape Toilet cubicle with standard dimensions of 2000 ± 25mm (Height) x 1000mm (Width) x 1550mm (Depth) consisting of 600 ± 10 mm width of door. The rate includes cost of 12mm Solid compact laminate board along with all necessary fixtures mentioned above. Nos 76.00 0

6.13.2 b) I - shape (front partition) Toilet cubicle with standard dimensions of 2000 ± 25mm (Height) x 1765mm (Width) consisting of 600 ± 10 mm width of door. The rate includes cost of 12mm Solid compact laminate board along with all necessary fixtures mentioned above Nos 39.00 0

6.14 VISION PANEL Size: 2.1m X 0.9m

6.14.1 CONTROL ROOM : VISION PANEL DETAILS (OPENABLE TYPE) 1. 2.layers of Gyproc Habito Board 12.5mm thick 2. Mass loaded Vinyl 3.5mm 3. Birch Plywood or Marine grade plywood with veneer melamine polished 4. Silicone Sealant at glass contact point with the ply/timber beading 5. Glazing panel at an angle of approx. 8-12 degrees as shown 6. Perforated aluminium or ply finish 7. Silica desiccant filling in packet format. Provision for future replacement to be ensured 8. Birch plywood OR marine grade plywood Note : All screws to be applied with silica gel while fastening for a complete seal through material boards. Decoupling Joint between the frame to achieve maximum transmission isolation to be ensured. FOR OPENABLE VISION PANEL : Recommended make >> Aluminium type with Laminated Glazed panel. Tostem Grants frame and installation. Sqm 1.95 0

6.15 AUDITORIUM DOORS D-A-G-05 (Auditorium Entracnce), D-A-G-10 (Auditrium Exit) Size: 1.8m X 2.4m

6.15.1 1. 2.5 mm thk TEXSA tecsound T50 2. 9 mm thk BWP plywood 3. Final finish as per internal material - 9-20 mm thk as per fixture detail 4. Perimeter seal SCHALL PS 1010 p along hinge end and top end of door frame 5. Tectus concealed hinge TE 6453d wt. Up to 300 kg or similar 6. 25x50 mm thk framework seasoned teakwood or Salwood as per architect's instruction 7. Outer finish on BWP plywood or birch ply with melamine polish as per architect's instruction thickness as per finish 8. All handles, Hinges and hardware to be considered in the Final Cost. Provision for Access control or special hardware if any shall be consider seperate Recommended Make: Soundworks, Acoustical Surfaces India Nos 2.00 0

6.16 AUDITORIUM DOORS-D-A-G-09 Size: 1.5m X 2.4m

6.16.1 1. 2.5 mm thk TEXSA tecsound T50 2. 9 mm thk BWP plywood 3. Final finish as per internal material - 9-20 mm thk as per fixture detail 4. Perimeter seal SCHALL PS 1010 p along hinge end and top end of door frame 5. Tectus concealed hinge TE 6453d wt. Up to 300 kg or similar 6. 25x50 mm thk framework seasoned teakwood or Salwood as per architect's instruction 7. Outer finish on BWP plywood or birch ply with melamine polish as per architect's instruction thickness as per finish 8. All handles, Hinges and hardware to be considered in the Final Cost. Provision for Access control or special hardware if any shall be consider seperate. Recommended Make: Soundworks, Acoustical Surfaces India Nos 1.00 0

6.17 CONTROL ROOM DOOR (Type-7) D-A-G-11 (Location : Control Room)

6.17.1 1. 2.5 mm thk TEXSA tecsound T50 2. 9 mm thk BWP plywood 3. Final finish as per internal material - 9-20 mm thk as per fixture detail 4. Perimeter seal SCHALL PS 1010 p along hinge end and top end of door frame 5. Tectus concealed hinge TE 6453d wt. Up to 300 kg or similar 6. 25x50 mm thk framework seasoned teakwood or Salwood as per architect's instruction 7. Outer finish on BWP plywood or birch ply with melamine polish as per architect's instruction thickness as per finish 8. All handles, Hinges and hardware to be considered in the Final Cost. Provision for Access control or special hardware if any shall be consider seperate. Recommended Make: Soundworks, Acoustical Surfaces India Nos 1.00 0

6.18 Control room window - VISION WINDOW W-A-G-02 to have following specs, Mention 2 glazing - 8 Degree 1. 2.layers of Gyproc Habito Board 12.5mm thick 2. Mass loaded Vinyl 3.5mm 3. Birch Plywood or Marine grade plywood with veneer melamine polished 4. Silicone Sealant at glass contact point with the ply/timber beading 5. Glazing panel at an angle of approx. 8-12 degrees as shown 6. Perforated aluminium or ply finish 7. Silica desiccant filling in packet format. Provision for future replacement to be ensured 8. Birch plywood OR marine grade plywood Sqm 4.00 0

TOTAL OF WOOD WORK 0

The rates shall include

a The structural steel frame work in line with design drawings made out of MS pipe sections / I Beams / Channels / Plates of approved make make of first quality confirming to IS standard.

b Preparing shop drawings based on architectural and structural drawings with required connections, all conforming to standards, code of practices, instructions of Structural consultant/PM.

c Take actual site measurement prior to fabrication and incorporate into shop drawings accordingly.

d Coordinating, scheduling and doing works as per site program.

e Straightening, cutting, bolting, welding including layout and assembly.

f Erecting, aligning, making plum and leveling to correct position as per shop drawings including required site repairs/adjustments.

g The steel structure shall be finish with the following, i. Surface Preparation – Blast cleaned to Sa 2.5 confirming to BS EN ISO 8501-1 ii. Primer : Zinc Rich Epoxy 75 micron iii. Barrier : Epoxy Mio 125 micron iv. Finish : Polyurethane – 50 Micron (Only for exposed steel)

h The steel design shall accommodate thermal stresses resulting from thermal expansion due to surface temperatures.

i Refer door schedule drawing no-A13-10 for type of finishes on particular door.

7.1A Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint. (D) In trussses and trussed purlins. Kg 4,064,968.00 0

7.1B Structural steel work (Confirming to IS 4923 latest version: Hollow Steel Sections for structural use) riveted, bolted or welded in builtup for all type sections, in framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per the structural designs and directions of Engineer in charge. Kg 48,647.00 0

7.2 Do as above but for steel work in Structural column of covered walkway - specialised CNC fabrication. Refer A16-06 Kg 25,703.00 0

7.3 Providing, fabricating and fixing G.I. railing system of approved design and profile, comprising vertical posts made of 38 mm dia G.I. pipes (1.2 mm thick), horizontal members of 19 mm dia G.I. pipes, and intermediate supports using G.I. flats (12 x 50 mm) at spacing of 1500 mm c/c, including necessary G.I. pipe plugs (16 mm dia) and all associated components as per approved drawings. Rmt 58.00 0

The work shall include cutting, bending, welding, grinding, and finishing of all members to achieve smooth and uniform joints, including factory welding and grinding smooth at connections. The railing shall be fixed to floor/structural base using suitable base plates, anchor fasteners, bolts, and necessary fixtures as approved by the Engineer-in-Charge, ensuring proper alignment, level, and rigidity.

The item shall include providing all materials, labour, tools and tackles, scaffolding, transportation, loading/unloading, and all incidental charges required to complete the work in accordance with approved shop drawings and specifications. The contractor shall prepare and submit detailed shop drawings for approval prior to execution. All complete as per drawings, specifications, and direction of Engineer-in-Charge. Note: For payment, only the weight of G.I. steel members shall be measured; fixing accessories such as nuts, bolts, fasteners, etc., shall not be measured separately. (refer-Detail-7-A12-12 & 07/A7-22)

7.4 Providing, fabricating and fixing S.S 304 Grade about 300mm high from finished floor level made out of 38mm dia SS pipe as handrail fixed to 10 x 50mm vertical MS flat and SS plate at bottom as shown in the drawing. Rate shall including including fabricating, fixtures, erecting, necessary welding, grinding, finishing, buffing to stainless steel pipe, providing and applying approved compatible primer and enamel paint to MS flat etc. including preparing shop drawings with prior approval of Architect / Engineer in charge etc. (Location : Glazing gaurd Railing) (refer-A12-12 & 03/A7-22) Rmt 252.00 0

7.5 Providing, fabricating and fixing double handle wooden railing about 800 mm high from finished floor level, comprising 38mm dia. wooden top rail fixed over MS support system as shown in drawing, including 20 × 10 mm MS flat cut to shape (2 Nos), 45 × 10 mm MS flat (2 Nos) for vertical supports, and 25 × 25 × 100 mm MS solid spacers in between at required intervals. The work includes supplying and fixing all components complete with necessary welding, cutting, drilling, grinding and finishing of MS members, providing and applying approved primer and enamel paint to all MS surfaces, and polishing/finishing of wooden railing with approved coating. Item to include all fixtures, fasteners, erection, and preparing shop drawings with prior approval of Architect/Engineer-in-charge, complete as per drawing and site requirements.(refer-A12-12 & 06/A7-22) Rmt 9.00 0

7.6 Providing, fabricating and fixing wall-mounted S.S. 304 grade railing at about 900 mm height from finished floor level, made out of 38 mm dia stainless steel pipe fixed to wall with suitable SS brackets as per drawing. The item shall include all necessary fixtures, anchor fasteners, welding, cutting, grinding, polishing and buffing to achieve stainless steel finish, complete in all respects. Rate shall include preparing shop drawings and obtaining prior approval of Architect /Engineer-in-charge, complete as per drawings and site requirements.(refer-A12-12 & 01/A7-22) Rmt 1,263.00 0

7.7 Providing, fabricating and fixing wall-mounted wooden railing at about 900 mm height from finished floor level, made out of 38 mm dia wooden member with approved polish finish, fixed to wall using suitable SS brackets as shown in drawing. The work shall include all fixtures, fasteners, necessary cutting, fitting, finishing, polishing, and providing and applying approved primer and enamel paint to MS components. Item includes erection, preparation of shop drawings and approval from Architect/Engineer-in-charge, complete as per drawings and site requirements.(refer-A12-12 & 02/A7-22) Rmt 183.00 0

7.8 Providing, fabricating and fixing wall-mounted wooden handrail system at a height of 1100 mm from finished floor level, comprising 38 mm diameter hardwood railing with approved polish finish, supported on stainless steel brackets anchored to wall, Further 1500mm c/c clamps to fixed glass as per approved drawings. The scope shall include 10 mm thick tempered laminated glass panel fixed in suitable glazing shoe/box with necessary sealant, MS backing plates, trims, and stainless steel fasteners as required. Wooden handrail shall be properly fixed over glass using approved connectors. All MS components shall be treated with approved primer and finished with enamel paint. The work includes all materials, labour, cutting, fitting, edge finishing, polishing, sealant application, hardware, and accessories required for complete installation. Item also includes preparation of shop drawings, obtaining approvals from Architect/Engineer-in-charge, and execution strictly as per drawings, specifications, and site conditions.(refer-A12-12 & 09/A7-22) Rmt 158.00 0

7.9 Providing and fixing wooden grab rail comprising 70 mm dia hardwood member with approved veneer finish, fixed at 900 mm height from finished floor level, supported on MS/GI sub-structure anchored to wall, including 15 mm thick plywood backing with veneer finish, SS/MS brackets, fasteners, and all necessary hardware. The item includes cutting, fitting, finishing, polishing, and application of primer and enamel paint to MS components, complete as per drawings and specifications.(refer-A12-12 & 10/A7-22) Rmt 455.00 0

7.10 Providing, fabricating and fixing fixed glass railing system comprising 10 mm thick tempered laminated safety glass panels, securely fixed in continuous aluminium shoe box with necessary gaskets, sealant, and anchoring arrangement as per approved drawings. The glass panels shall be finished with stainless steel capping at top, properly aligned and fixed. The base shoe shall be supported on MS flat (150 x 9 mm) with approved primer and enamel paint, anchored to RCC base, and integrated with surrounding stone dry cladding as shown.The work shall include all materials, labour, cutting, edge finishing, polishing, drilling, grouting, application of sealant, SS fasteners, and accessories required for complete installation. All exposed metal components shall be finished to approved specifications. The item includes preparation of shop drawings, obtaining approvals from Architect/Engineer-in-charge, and execution strictly as per drawings, specifications, and site conditions, complete in all respects.(refer-A12-12 & 08/A7-22) Rmt 38.00 0

7.11 Providing and fixing 2mm thick SS coping about 225mm wide at top of parapet top with necessary accessories as shown in drawing. (Refer-A12-08 & Detail A11-01) Rmt 126.00 0

7.12 Non-fire rated Hollow metal doors

Providing and fixing of Standard duty Hollow metal doors confirming to IS 16074 & IS 4351 made of pressed galvanized steel confirming to IS 277 with the following specification. Doors shall be manufcatured in ISO 9001: 2015 certified company for quality management. Doors shall be with vision glass and louver as a part of complete assembly.

Door frame shall be single rebate grooved profile of size 125 x 55mm made out of minimum 1.20mm (18gauge) thick galvanized steel sheet. Frames shall be mitered only. Frames shall be field assembled with self tabs. Bolted & butted joints are not acceptable. Frames to have inbuild grooved sealing system with appropriate PVC seal. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. once frames installed it should be grouted with non fire rated PUF.

Door leaf shall be 46mm thick fully flush double skin door, with or without vision lite. Door leaf shall be manufactured from minimum 0.8mm (22guage) thick galvanised steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be resin bonded honeycomb core. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors integrated astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be provided a clipon arrangement. Glass shall be minimum 4mm clear toughned glass with suitable gaskets as per manufacturers recommendation with a clipon arrangement.

All doors and frames shall be finished Pure Polyester Powder coated and shall have passed minimum 500 hours of salt sprey test.

Rate shall include supply and installation of frame, shutter as a complete assembly. All hardware, seals & glass including tapes cost will be paid extra as per the hardware schedule

7.12.1 Door DS-A-L-01, DS-B-1F-05, DS-F-G-04, DS-G-G-03, DS-J-L-09, DS-J-G-05, DS-J-1F-05, DS-J-1F-07, D-M-G-01, D-M-G-02 (Location PHE Shaft, Toilet-Male & Female), sigle leaf, size 600mm x 1500mm, with SS hardware of approved make Nos 10.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

7.12.2 Door (Type-8) D-A-G-06, D-A-G-07 (Location Audi Green Room Toilets), D-J-L-20, D-J-L-21 (Location : Staff Toilet-M & F), sigle leaf, size 750mm x 2100mm, with SS hardware of approved make Nos 4.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Surface door closer

d) Door stopper

7.12.3 Door (Type-7) D-B-1F-04, D-F-G-07, D-G-L-08, D-G-G-07, D-J-L-18, D-J-1F-10, D-M-G-02 (Location : Janitor room), D-B-2F-05 (Location : Director Toilet), (Location : Staff Toilet-M & F), sigle leaf, size 750mm x 2100mm, with SS hardware of approved make Nos 8.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Surface door closer

d) Door stopper

7.12.4 Door (Type-7A) D-B-L-01 (Location : Security Monitor), size 1200mm x 2100mm, with double unequal leaves door shutters (900mm + 300mm) with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

7.12.5 Door (Type-7B)D-A-G-12, (Location Service Passage), size 1500mm x 2100mm, with double leaf door shutters with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on one leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on other leaf)

7.12.6 Door (Type-7A) D-J-L-04 (Location Service Passage), size 1500mm x 2100mm, with double leaf door shutters with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on one leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on other leaf)

7.12.7 Door (Type-DS1) DS-A-G-02 (Location PHE Shaft), sigle leaf, size 600mm x 1800mm, with 35mm thick sand stone cladding on outer face, SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.12.8 Door (Type-DS1) DS-B-2F-03, DS-J-1F-09 (Location PHE Shaft), sigle leaf, size 600mm x 1800mm, with SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.12.9 Door (Type-DS1) DS-A-G-03, DS-J-L-03, DS-J-L-04,DS-A-1F-03, DS-J-2F-03, DS-J-4F-03, D-B-1F-02 (Location PHE Shaft), sigle leaf, size 600mm x 1800mm, with SS hardware of approved make Nos 7.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.12.10 Door D-A-1F-04, D-C-1F-01, D-F-G-03, D-G-L-01, D-G-G-02, D-G-1F-01, D-J-L-14, D-J-G-04, D-J-1F-07, D-J-2F-03 (Location: Service Passage, Bontiful Gallery-BOH, Temp Gal-Serv, Utsah Gal-BOH, Siddhi Gal-BOH), size 2700mm x 3000mm, with double unequal leaves door shutters (1200mm + 1500mm) with pait finished 12mm thick gypsum board + 12mm thick Plywood backing on one side of the door, including SS hardware of approved make Nos 5.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 6 Nos.

b) Provision for Access control

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

7.12.11 Door DS-A-2F-02 (Location PHE Shaft), sigle leaf, size 600mm x 2100mm, with 35mm thick stone cladding on outer face, SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.12.12 Door (Type-7) D-B-L-04 (Location : Staff Break room), & D-B-L-07 (Location : Industrial First Aid) & D-B-M-02 (Location : Security), D-C-G-01 (Location : baby care), D-F-1F-07 (Location : Janitor room), D-J-L-17, D-J-G-08 (Location : Baby care), D-J-3F-02 (Location : Service passage), D-J-4F-13 (Location : Kitchen terrace), D-J-4F-14 (Location : Bakery+storage), D-K-G-02 (Location : Store), D-K-G-05 (Location : Service door), D-V-G-01 (Location : Security cabin) size 900mm x 2100mm, with signle leaf door shutters with SS hardware of approved make Nos 12.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on one leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on other leaf)

e) Lever Handle

7.12.13 Door (Type-7) D-B-L-06 (Location: Security locker, access door), size 900mm x 2100mm, with single leaf door shutters with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 3 Nos.

b) Provision for Access control

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No.

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.12.14 Door (Type-8) D-B-L-08, D-B-L-09, D-B-M-08, D-B-M-09, D-B-2F-12, D-B-2F-13, (Location: Staff Toilet M & F, Staff Lokcer room, Toilet male & Female, Kitchen admin), size 900mm x 2100mm, with single leaf door shutters with SS hardware of approved make Nos 6.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer

d) Lever Handle

7.12.15 Door (Type-7) D-B-M-07, D-B-M-10, D-J-4F-11, D-K-G-03 (Location: Staff Toilet M & F, Staff Lokcer room, Toilet male & Female, Kitchen admin), size 900mm x 2100mm, with single leaf door shutters with SS hardware of approved make Nos 4.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer

d) Lever Handle

7.12.16 Door (Type-7A) D-B-L-10 (Location : Storage, AV Store), size 1200mm x 2100mm, with double unequal leaves door shutters (900mm + 300mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No.

d) Lever Handle

7.12.17 Door (Type-7) D-B-L-11 (Location : Janitor room), size 750mm x 2100mm,with single leaf door shutters with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No.

d) Lever Handle

7.12.18 Door (Type-7B) D-B-L-13 (Location : Waste Management), size 1500mm x 2100mm, with double equal leaves door shutters (750mm + 750mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Lever Handle with roses & Escutcheons

c) heavy duty floor springs of adequate capacity

7.12.19 Door (Type-DS1) DS-B-1F-01, DS-B-1F-03, DS-F-1D-04 (Location PHE Shaft), sigle leaf, size 900mm x 1500mm, with SS hardware of approved make Nos 3.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.12.20 Door DS-B-L-01 (Location : PHE Shaft), sigle leaf, size 600mm x 1500mm, with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.12.21 Door (Type-7A) D-B-M-01 (Location: Housekeeping), size 1200mm x 2100mm, with double unequal leaves door shutters (900mm + 300mm) with including SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No.

d) Lever Handle

7.12.22 Door (Type-7B) D-B-M-05 (Location: Staff Ent/Fire Exit, access door), size 1800mm x 2100mm, with double equal leaf door shutters (900mm + 900mm) with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 6 Nos.

b) Provision for Access control

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No.

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.12.23 Door (Type-7) D-B-M-06, D-C-G-04 (Location: Janitor room, Kitchen changing room), sigle leaf, size 750mm x 2100mm, with SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer

d) Door stopper

e) Lever Handle

7.12.24 Door (Type-DS1) DS-B-L-02, DS-B-M-02, DS-B-G-02 (Location : FF shaft, Plumbing Shaft), sigle leaf, size 900mm x 1500mm, with SS hardware of approved make Nos 3.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.12.25 Door (Type-DS1) DS-B-M-03, DS-B-G-05 (Location :Plumbing Shaft), sigle leaf, size 600mm x 1500mm, with SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.12.26 Door (Type-7) D-B-G-03, D-B-G-04, D-B-G-11, D-B-G-12, D-B-1F-05, D-B-1F- 06, D-F-G-05, D-F-G-06, D-F-1F-08, D-F-1F-09, D-G-L-07, D-G-L-09, D-G-G-08, D-G-G-09, D-J-L-15, D-J-L-16, D-J-G-07, D-J-G-10, D-J-1F-03, D-J-1F-05, D-J-1F-09, D-J-1F-11, D-J-2F-04, D-J-2F-05, D-J-4F-02, D-J-4F-05, D-M-G-01, D-M-G-03 (Location Toilet Female & Male), sigle leaf, size 900mm x 2400mm, with SS hardware of approved make Nos 28.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No.

d) Door stopper

7.12.27 Door (Type-7B) D-B-G-06 (Location: Furniture store), size 1500mm x 2400mm, with double equal leaves door shutters (750mm + 750mm) with pait finished 12mm thick gypsum board + 12mm thick Plywood backing on one side of the door, including SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

7.12.28 Door (Type-7A) D-B-G-07 (Location: Service passage), size 2700mm x 3000mm, with double unequal leaves door shutters (1200mm + 1500mm) with pait finished 12mm thick gypsum board + 12mm thick Plywood backing on one side of the door, including SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

7.12.29 Door (Type-7A) D-J-L-02 (Location: Service passage), size 2700mm x 3000mm, with double unequal leaves door shutters (1200mm + 1500mm) with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Access control

f) Pull/Push handle

7.12.30 Door (Type-7) D-B-G-10 Location : Janitor room), sigle leaf, size 750mm x 2100mm, with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Surface door closer

d) Door stopper

7.12.31 Door DS-B-G-01 (Location PHE Shaft), sigle leaf, size 600mm x 1800mm, with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

7.12.32 Door (Type-7A) D-B-G-07 (Location: Service passage), size 2700mm x 3000mm, with double unequal leaves door shutters (1200mm + 1500mm) with pait finished 12mm thick gypsum board + 12mm thick Plywood backing on one side of the door, including SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 6 Nos.

b) Provision for Access control

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Pull/Push handle

7.12.33 Door (Type-DS2) DS-B-2F-02 (Location PHE Shaft), sigle leaf, size 1200mm x 1800mm, with double equal leaves door shutter (600mm x 600mm), with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Allen key Dead lock

c) Concealed handle

7.12.34 Door (Type-7A) D-C-L-01 (Location : Wet waste), sigle leaf, size 1500mm x 2100mm, with double unequal leaves door shutter (900mm + 600mm) with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Surface door closer

d) Door stopper

7.12.35 Door (Type-7B) D-C-G-02, D-E-1F-02, D-F-1F-04 (Location : Kitchen-BOH, AHU Entry, Pantry-BOH), size 1500mm x 2100mm, with double equal leaves door shutters (750mm + 750mm) with fire rated SS hardware of approved make Nos 3.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Lever Handle with roses & Escutcheons

d) Surface door closer

7.12.36 Door (Type-12) D-C-G-07, D-C-G-08 (Location : Kitchen), size 1500mm x 2100mm, with double equal leaves door shutters (750mm + 750mm) with fire rated SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Pull / Push handle

c) heavy duty floor springs of adequate capacity

d) Door stopper

e) Vision panel-300mm x 300mm

7.12.37 Door (Type-12) D-C-G-09 (Location : Kitchen-FOH), size 1800mm x 2100mm, with double equal leaves door shutters (900mm + 900mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Pull / Push handle

c) heavy duty floor springs of adequate capacity

d) Door stopper

e) Vision panel-300mm x 300mm

7.12.38 Door (DS-3)DS-C-G-02, DS-G-L-02 (Location : PHE Shaft), sigle leaf, size 900mm x 1500mm, with double unequal leaves shutter (600mm + 300mm) with SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.12.39 Door (Type-7B) D-B-G-06 (Location: Furniture store), size 1500mm x 2400mm, with double equal leaves door shutters (750mm + 750mm) with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

7.12.40 Door (Type-7A) D-F-G-04 (Location: Temp Gal-Serv), size 2700mm x 3000mm, with double unequal leaves door shutters (1200mm + 1500mm) with 35mm thick sand stone fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty (suitable to take additional load of sand stone) size 100 x 75 x 3mm, SSS - 6 Nos.

b) Narrow profile Mortise Dead lock, 35 BS/8mm, SSS finish with cyl, escutheion suitable for double leaf door

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.12.41 Door (Type-7B) D-F-G-10 (Location : Service passage), size 3000mm x 3000mm, with Double leaf equal door shutters (1500mm + 1500mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on one leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on other leaf)

e) Lever Handle

7.12.42 Door (Type-7B) D-F-1F-02, D-F-1F-03 (Location : Storage, VIP lounge-Pantry), size 1500mm x 2400mm, with double equal leaf door shutter (750mm + 750mm) with 12mm thick Plywood backing on one side of the door finish with approved 4mm thick veneer finish with SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs and key opening

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle

7.12.43 Door (Type-7B) D-F-1F-05 (Location : Service passage), sigle leaf, size 1200mm x 2400mm, with double equal leaves door shutter (600mm + 600mm) with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Surface door closer

d) Door stopper

7.12.44 Door (Type-3) D-F-1F-12 (Location VIP Lounge-Entry), overall size 3000mm x 2400mm, with double equal leaf door shutter (900mm + 900mm) with 12mm thick Plywood backing on one side of the door finish with approved 4mm thick veneer finish with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Motorised dead lock

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No.

d) Pull/Push handle

7.12.45 Door (DS-1) DS-F-1F-01 (Location : Electrical Shaft), sigle leaf, size 900mm x 1800mm, with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.12.46 Door (Type-3) D-G-G-03, D-G-G-06, D-G-1F-02, D-G-1F-06, D-J-L-08 (Location : Utsah Gal-FOH, Bontiful Gujarat bridge ), overall size 3000mm x 3600mm, out of which 1800mm wide x 2400mm high openable double leaf door with 12mm thick Plywood backing on one side of the door finish with approved 4mm thick veneer finish with SS hardware of approved make Nos 5.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty (suitable to take additional load of sand stone) size 100 x 75 x 3mm, SSS - 6 Nos.

b) Pull/Push handle

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No.

d) Door stopper

7.12.47 Door (Type-7) D-G-G-04, D-J-L-10, D-J-G-12, D-J-1F-13, D-J-2F-08, D-K-G-01, D-K-G-04, D-K-G-05, D-L-G-01, D-L-G-02 (Location : Kiosk, AV Shaft, Ticketing counter, Clock room, Service door, Security cabin), sigle leaf, size 900mm x 2400mm, with 12mm thick Plywood backing on one side of the door finish with approved 4mm thick veneer finish with SS hardware of approved make Nos 9.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No.

d) Door stopper

e) Lever handle

7.12.48 Door (Type-7A) D-J-G-02 (Location : Service passage), sigle leaf, size 1200mm x 2400mm, with double unequal leaves door shutter (900mm + 300mm) with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Concealed door closer

d) Door stopper

e) Lever handle

7.12.49 Door (Type-7B) D-J-1F-04, D-J-1F-06, D-J-2F-06 (Location : Service passage, Baby care), sigle leaf, size 900mm x 2400mm, with double equal leaves door shutter (450mm + 450mm) with SS hardware of approved make Nos 3.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Surface door closer

d) Door stopper

e) Lever handle

7.12.50 Door (Type-7) D-J-G-09, D-J-4F-04 (Location : Janitor room), size 750mm x 2400mm, with Single leaf door shutters with fire rated SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on one leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on other leaf)

e) Lever Handle

7.12.51 Door (Type-9C) D-J-3F-06 (Location : Landing store room), sigle leaf, size 750mm x 2100mm, with 35mm thick sand stone cladding on outer face, SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset heavy duty hinges (suitable to take additional load of sand stone) size 100 x 75 x 3mm, SSS - 3 Nos.

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on one leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on other leaf)

e) Lever Handle

7.12.52 Door (Type-7B) D-J-4F-10 (Location : Café kitchen), size 1475mm x 2400mm, with double equal leaves door shutters (737.5mm + 737.5mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock

c) Pull/push handel

d) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No.

e) Door stopper

7.12.53 Door (Type-11) D-J-4F-12 (Location : Kitchen ramp), Double leaf, size 1500mm x 2100mm, with double unequal leaves door shutter (900mm + 600mm) with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock

c) Pull/push handel

d) Surface door clouser - 1 No.

e) Door stopper

f) Floor spring

7.12.54 Door (Type-7) D-N-G-01, D-FS-G-01 (Location : Security cabin) size 900mm x 2250mm, with signle leaf door shutters with fire rated SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on one leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on other leaf)

e) Lever Handle

7.13 Insulated Hollow metal fire rated doors

Providing and fixing of medium duty hollow metal fire rated doors as per IS 3614: 2021, for 120min integrity & 30min. insulation. Pressed galvanized steel confirming to IS 277 with the following specification. Recommended fire door shall be tested to IS 17518 (Part 1) : 2022 / ISO 3008-1: 2019 from CBRI lab and manufactured in ISO 9001: 2015 certfied company for quality management. ISI labled fire door shall be with fire rated hardware and vision panel all as a complete assembly and shall not be more than 58kg/Sqmt in weight. Proper label confirming the type of door and the hourly rating is mandatory. NOTE- Doors tested in latched condition cannot be replaced with unlatched doors (Deadbolt & Handle) in actual site condition. Need independent testing for both latched and unlatched doors. Ref Page No-8 & 10, Sec: 7.2.9 & 7.3.6 of Builder’s Hardware IS3614:2021.

Door frame shall be step rebate grooved profile of size 125 x 75mm made out of 1.20mm (18gauge) minimum thick galvanized steel sheet. Frames shall be mitered and field assembled with self tabs. Frames to have inbuild grooved sealing system for taking fire rated EPDM seals. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Frames shall be filled with fire rated puff.

Door leaf shall be 60mm thick fully flush double skin step design door, insulated with or without vision lite. Door leaf shall be manufactured from 1.2mm (18guage) minimum thick galvanised steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be high density mineral wool with a density not less than 120kg/m3 as an insulation material. Intumescent seals 15 x 1.5mm to be provided. All ISI labelled doors shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors integrated astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable shall be maximum 200 x 300mm (or max 0.06sq.mt) with clear borosilicate fire rated glass of 6mm. Glass shall be fixed with suitable gasket and with clip-on arrangement.

Door and frames shall be finished Pure Polyester Powder coated (15 years guarantee) and shall have passed minimum 500 hours of salt spray test.

Rate shall include supply and installation of frame,shutter as a complete assembly including all hardware, smoke seals & glass with tape.

7.13.1 Door D-A-L-01 (Location Server Room) & D-B-L-12 (Location : UPS bank) & D-B-M-11 (Location : BMS room) & D-B-M-12 (Location : Electrical room) & D-D-L-01 (Location : IT work room), size 1200mm x 2100mm, with double unequal leaves door shutters (900mm + 300mm) with fire rated SS hardware of approved make Nos 5.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Narrow profile Mortise Dead lock, 35 BS/8mm, SSS finish with cyl, escutheion suitable for double leaf door

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.13.2 Door (Type-9) D-A-G-04, D-G-G-01 (Location: AHU - Auditorium, AHU-GF Gallery), size 1800mm x 2400mm, with double unequal leaves door shutters (1200mm + 600mm) with 35mm thick sand stone fire rated SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty (suitable to take additional load of sand stone) size 100 x 75 x 3mm, SSS - 6 Nos.

b) Narrow profile Mortise Dead lock, 35 BS/8mm, SSS finish with cyl, escutheion suitable for double leaf door

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.13.3 Door D-A-G-09 (Location: Auditorium-BOH) & D-G-L-02 (Location : Fire exit lobby), size 1500mm x 2400mm, with double equal leaf door shutters (750mm + 750mm), with vision window of size 300mm x 300mm with 6mm thick fire rated glass (#9), with fire rated SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Fire rated Single point surface panic latch, as per EN1125, Silver finish

c) Concealed door clouser , Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on other leaf)

7.13.4 Door (Type-7B) D-B-M-13, D-G-L-03, D-G-L-14 (Location : AHU Mezz, LGF, AHU Tunnel), size 1500mm x 2400mm, with double equal leaf door shutters (750mm + 750mm), with fire rated SS hardware of approved make Nos 3.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on one leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on other leaf)

e) Lever Handle with roses & Escutcheons

7.13.5 Door (Type-11) D-A-G-14, D-G-L-11, D-G-G-10, D-G-1F-05, D-J-L-06, D-J-G-03, D-J-G-11, D-J-1F-01, D-J-1F-12, D-J-2F-02, D-J-2F-07, D-J-3F-05, D-J-4F-03, D-J-4F-09 (Location: Fire Escape Staircase) & Door D-A-1F-03, D-B-1F-03, D-C-1F-03 (Location: Fire Escape Staircase) & D-B-G-09 (Location : Lobby-Fire door) & D-G-L-04 (Location : Utsah Gal-Fire exit), D-G-L-10 (Location : Fire sepration door) & D-J-L-07, D-J-1F-02 (Location : Siddhi Gal-Fire exit) & D-J-2F-01, D-J-3F-09 (Location : Ramp fire exit), size 1500mm x 2400mm, with double unequal leaves door shutters (900mm + 600mm) with, with vision window of size 300mm x 300mm with 6mm thick fire rated glass (#9), fire rated SS hardware of approved make Nos 24.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Fire rated Single point surface panic latch, as per EN1125, Silver finish

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on one leaf)

7.13.6 Door (Type-9) D-A-1F-01 (Location: AHU - GAURAV GALLERY), size 1800mm x 1800mm, with double unequal leaves door shutters (1200mm + 600mm) with 35mm thick sand stone fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty (suitable to take additional load of sand stone) size 100 x 75 x 3mm, SSS - 6 Nos.

b) Narrow profile Mortise Dead lock, 35 BS/8mm, SSS finish with cyl, escutheion suitable for double leaf door

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Concealed handle- 1 No.

f) Brush bottom seal

7.13.7 Door (Type-11) D-A-2F-01, D-B-L-03, D-B-M-03, D-B-M-04, D-B-G-08, D-C-G-05, D-F-L-01, D-F-L-02, D-J-B-02, D-J-L01, D-J-3F-01, D-J-3F-03 (Location: Fire Escape Staircase, Fire Exit), size 1500mm x 2100mm, with double unequal leaves door shutters (900mm + 600mm) with, with vision window of size 300mm x 300mm with with 6mm thick fire rated glass (#9), fire rated SS hardware of approved make Nos 12.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Fire rated Single point surface panic latch, as per EN1125, Silver finish

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on one leaf)

7.13.8 Door (Type-7A) D-B-L-02, D-C-L-03, D-C-L-04, D-C-L-05 , D-C-L-06, D-C-L-07, D-C-L-08, D-D-L-02, 03, 04, 05, 06, 07, 08 (Location: Chiller room, Moving tool storage, Crate storage, Shipping receiving, Transit store, Crating/Uncrating, Plinth & Panel), size 2700mm x 3000mm, with double unequal leaves door shutters (1200mm + 1500mm) with fire rated SS hardware of approved make Nos 14.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 100 x 75 x 3mm, SSS - 6 Nos.

b) Narrow profile Mortise Dead lock, 35 BS/8mm, SSS finish with cyl, escutheion suitable for double leaf door

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.13.9 Door (Type-7A) D-B-L-05 (Location: Quartine room, access door), size 2700mm x 3000mm, with double unequal leaves door shutters (1200mm + 1500mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 150 x 100 x 3mm, SSS - 6 Nos.

b) Provision for Access control

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.13.10 Door (Type-7B) D-B-1F-01, D-C-1F-02, D-F-1F-01, D-G-L-15, D-J-L-03, D-J-L-19, D-J-G-05, D-J-M-01, D-J-3F-04, D-J-3F-07, D-J-3F-10 (Location: AHU-Gaurav Gallery, AHU Restaurant, Pump room, AHU-Ent lobby, AHU, AHU curved ramp, AHU above floor), size 1500mm x 2100mm, with double equal leaves door shutters (750mm + 750mm) with fire rated SS hardware of approved make Nos 11.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 100 x 75 x 3mm, SSS - 6 Nos.

b) Narrow profile Mortise Dead lock, 35 BS/8mm, SSS finish with cyl, escutheion suitable for double leaf door

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.13.11 Door (Type-11B) D-B-1F-07, D-J-L-22 (Location: Fire Escape Staircase), size 1200mm x 2400mm, with single leaves door shutters with, with vision window of size 300mm x 300mm with with 6mm thick fire rated glass (#9), fire rated SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Fire rated Single point surface panic latch, as per EN1125, Silver finish

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on one leaf)

7.13.12 Door (Type-11B) D-B-2F-08 (Location: Fire Escape Staircase), size 1200mm x 2100mm, with single leaf door shutters , with vision window of size 300mm x 300mm with with 6mm thick fire rated glass (#9), fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Fire rated Single point surface panic latch, as per EN1125, Silver finish

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on one leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on one leaf)

7.13.13 Door (Type-7A) D-C-L-02 (Location : Metering Kiosk), sigle leaf, size 2100mm x 1500mm, with double unequal leaves door shutter (900mm + 600mm) with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Surface door closer

d) Door stopper

7.13.14 Door (Type-11A) D-F-G-11, D-F-1F-06, D-G-L-12 (Location: Fire Escape Staircase, Tunnel Fire Exit), size 1800mm x 2400mm, with double equal leaves door shutters (900mm + 900mm) with, with vision window of size 300mm x 300mm with 6mm thick fire rated glass (#9), fire rated SS hardware of approved make Nos 3.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Fire rated Single point surface panic latch, as per EN1125, Silver finish

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on one leaf)

7.13.15 Door (Type-11) D-F-2F-01 (Location: Fire Shaft) , overall size 1500mm x 2100mm, with double unequal leaves door shutters (900mm + 600mm) with, with vision window of size 300mm x 300mm with 6mm thick fire rated glass (#9), fire rated SS hardware of approved make Nos 5.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Fire rated Single point surface panic latch, as per EN1125, Silver finish

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on one leaf)

7.13.16 Door (Type-7B) D-G-1F-03 (Location: AHU), size 1800mm x 2400mm, with double equal leaves door shutters (900mm + 900mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.13.17 Door (Type-7B) D-J-B-01, D-J-B-07 (Location: Pump room), size 2100mm x 2400mm, with double equal leaves door shutters (1050mm + 1050mm) with fire rated SS hardware of approved make Nos 2.00 0

a) 5 Knl, Butt hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.13.18 Door (Type-7A) D-J-B-03 (Location: Staircase), size 1200mm x 2100mm, with double eunqual leaves door shutters (900mm + 300mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.13.19 Door (Type-7A) D-J-B-04, D-J-B-05, D-J-B-06 (Location: LT panel area, DG area), size 1500mm x 2100mm, with double unequal leaves door shutters (900mm + 600mm) with fire rated SS hardware of approved make Nos 3.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.13.20 Door (Type-7) D-J-L-09 (Location: Lift lobby), size 1250mm x 3600mm, with single door shutters with 12mm thick Plywood backing on one side of the door finish with approved 4mm thick veneer finish with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Pull/Push handle

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on one leaf)

7.13.21 Door (Type-7) D-J-L-11 (Location: Lift lobby), size 1200mm x 3600mm, with single equal leaves door shutters , with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Concealed handle

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on one leaf)

7.13.22 Door (Type-7A) D-J-3F-08 (Location: Lift lobby), size 1500mm x 2400mm, with double eunqual leaves door shutters (900mm + 600mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs, push button inside, emergency opening outside

c) Concealed door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.13.23 Door (Type-7) D-J-3F-11 (Location: Service passage), size 900mm x 2100mm, with single leaves door shutters with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

e) Lever Handle with roses & Escutcheons

7.16 Un-Insulated Hollow metal fire doors

Providing and fixing of medium duty hollow metal fire rated doors as per IS 3614: 2021, for 120min integrity only.Pressed galvanized steel confirming to IS 277 with the following specification. Recommended fire door shall be tested to IS 17518 (Part 1) : 2022 / ISO 3008-1: 2019 from CBRI lab and manufactured in ISO 9001: 2015 certfied company for quality management. ISI labled fire door shall be with fire rated hardware and vision panel all as a complete assembly and shall not be more than 34kg/Sqmt in weight. Proper label confirming the type of door and the hourly rating is mandatory. NOTE- Doors tested in latched condition cannot be replaced with unlatched doors (Deadbolt & Handle) in actual site condition. Need independent testing for both latched and unlatched doors. Ref Page No-8 & 10, Sec: 7.2.9 & 7.3.6 of Builder’s Hardware IS3614:2021.

Door frame shall be single rebate grooved profile of size 125 x 55mm made out of 1.20mm (18gauge) minimum thick galvanized steel sheet. Frames shall be mitered and field assembled with self tabs. Frames to have inbuild grooved sealing system for taking fire rated EPDM seals. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Frames shall be filled with fire rated puff (paid extra).

Door leaf shall be 46mm thick fully flush double skin door, sandwiched panel un-insulated with or without vision lite. Door leaf shall be manufactured from 1.2mm (18guage) minimum thick galvanised steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be honeycomb core. All doors shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors integrated astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable shall be maximum 150 x 750mm (or max 0.12sq.mt) with clear borosilicate fire rated glass of 6mm. Glass shall be fixed with suitable gasket and with clip-on arrangement.

Door and frames shall be finished Pure Polyester Powder coated and shall have passed minimum 500 hours of salt sprey test.

Rate shall include supply and installation of frame,shutter as a complete assembly including all hardware, smoke seals & glass with tape.

7.16.1 Door (Type-DS3) DS-A-L-02, DS-G-G-01, DS-G-1F-01 (Location Fire Shaft), size 900mm x 1500mm, with double unequal leaves door shutters (600mm + 300mm) with fire rated SS hardware of approved make Nos 3.00 0

a) 5 Knl, Butt hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Allen key Dead lock, suitable for double leaf

7.16.2 Door (Type-11) D-A-M-01, D-J-L-12, D-J-L-13 (Location Mezzanine Fire Exit, Fire Exit), size 1500mm x 2100mm, with double unequal leaves door shutters (900mm + 600mm) with vision window of size 300mm x 300mm with 6mm thick fire rated glass (#9), fire rated SS hardware of approved make Nos 3.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Fire rated Single point surface panic latch, as per EN1125, Silver finish

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

7.16.3 Door (Type-11) D-A-G-08 (Location Auditorium Fire Exit), size 1500mm x 2100mm, with double unequal leaves door shutters (900mm + 600mm) with vision window of size 300mm x 300mm with 6mm thick fire rated glass (#9), fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Fire rated Single point surface panic latch, as per EN1125, Silver finish

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

7.16.4 Door (Type-DS3) DS-A-G-01, DS-F-G-05, DS-F-1F-05, DS-J-G-06 , DS-J-1F-06, DS-J-2F-01, DS-J-2F-02 (Location FF Shaft), size 900mm x 1800mm, with double unequal leaves door shutters (600mm + 300mm) with fire rated SS hardware of approved make Nos 7.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Allen key Dead lock, suitable for double leaf

c) Concealed handles

7.16.5 Door (Type-DS3) DS-A-1F-01 (Location: Fire Shaft), size 1200mm x 1800mm, with double unequal leaves door shutters (600mm + 600mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Allen key Dead lock, suitable for double leaf

c) Concealed handle from outside

7.16.6 Door (Type-DS) DS-A-1F-02 (Location: Fire Shaft), size 1200mm x 1800mm, with double leaf door shutters with fire rated SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Allen key Dead lock, suitable for double leaf

c) Concealed handle from outside

7.16.7 Door (DS-1) DS-A-2F-01 (Location Fire Shaft), size 900mm x 2100mm, with single leaf door shutter with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock, suitable for double leaf

7.16.8 Door (Type-DS1) DS-B-M-01, DS-B-G-03, DS-B-1F-02, DS-C-L-01, DS-C-1F-01, DS-F-L-02, DS-F-L-03, DS-G-L-01, DS-G-L-03, DS-G-1F-02, DS-J-G-08, DS-J-3F-02 (Location : FF shaft, Plumbing shaft, HVAC shaft, FF Hose shaft), sigle leaf, size 900mm x 1500mm, with SS hardware of approved make Nos 12.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.16.9 Door (DS-2) DS-B-G-04 (Location : FF shaft), double equal leaf, size 1200mm x 1800mm, with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock, suitable for double leaf

c) Concealed handle

7.16.10 Door (Type-DS-1) DS-B-1F-04 , DS-F-L-01, DS-F-G-01, DS-F-G-03, DS-F-1F-03, DS-G-G-02. DS-J-1F-08 (Location : FF shaft, Electrical shaft, FF House shaft), single equal leaf, size 900mm x 1800mm, with SS hardware of approved make Nos 7.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.16.11 Door (Type-DS2) DS-B-2F-01, DS-J-L-01, DS-J-L-02, DS-J-1F-01, DS-J-4F-01, DS-J-4F-02 (Location FF Shaft), size 900mm x 1800mm, with double equal leaves door shutters (450mm + 450mm) with fire rated SS hardware of approved make Nos 6.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Allen key Dead lock, suitable for double leaf

7.16.12 Door (Type-11) D-C-L-09 (Location: Fire Escape Staircase), size 1800mm x 2100mm, with double unequal leaves door shutters (1200mm + 600mm) with, with vision window of size 300mm x 300mm with 6mm thick fire rated glass (#9), fire rated SS hardware of approved make Nos 4.00 0

a) 5 Knl, Ball bearing offset hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Fire rated Single point surface panic latch, as per EN1125, Silver finish

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on one leaf)

7.16.13 Door (Type-7) D-C-L-10, D-C-L-11 (Location : Loading bay Steps, Ramp), size 1200mm x 2100mm, with double unequal leaves door shutters (900mm + 300mm) with SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

7.16.14 Door (Type-7A) D-E-L-01 (Location : AV store), size 200mm x 2100mm, with double unequal leaves door shutters (900mm + 300mm) with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

7.16.15 Door (Type-7A) DS-C-1F-02, DS-C-1F-03 (Location FF Shaft, HVAC shaft), overall size 900mm x 1500mm, with double unequal leaves door shutters (600mm + 300mm) with fire rated SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Allen key Dead lock, suitable for double leaf

c) Concealed handle

7.16.16 Door (Type-7) DS-C-G-04 (Location: FF shaft), size 1200mm x 1800mm, with double equal leaves door shutters (600mm + 600mm) with 35mm thick sand stone fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty (suitable to take additional load of sand stone) size 100 x 75 x 3mm, SSS - 6 Nos.

b) Allen key Dead lock, suitable for double leaf

c) Concealed handle

7.16.17 Door (Type-7B) D-E-1F-01, (Location: AHU-1F), size 1500mm x 2100mm, with double equal leaves door shutters (750mm + 750mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset hinges heavy duty size 100 x 75 x 3mm, SSS - 6 Nos.

b) Narrow profile Mortise Dead lock, 35 BS/8mm, SSS finish with cyl, escutheion suitable for double leaf door

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on bigger leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on smaller leaf)

e) Lever Handle with roses & Escutcheons

7.16.18 Door (Type-DS1) DS-F-G-02, DS-F-1F-02, DS-J-G-07 (Location: Plumbing Shaft), size 600mm x 1800mm, with single leaf door shutters with fire rated SS hardware of approved make Nos 3.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Allen key Dead lock

c) Concealed handle from outside

7.16.19 Door (Type-DS1) DS-G-L-04, DS-G-G-06, DS-G-1F-03, DS-J-L-06, DS-J-L-07, DS-J-L-08, DS-J-G-02, DS-J-G-03, DS-J-G-04, DS-J-1F-02, DS-J-1F-03, DS-J-1F-04 (Location: HVAC Shaft, Electrical shaft, DG shaft), size 600mm x 1500mm, with single leaf door shutters with fire rated SS hardware of approved make Nos 12.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Allen key Dead lock

c) Concealed handle from outside

7.16.20 Door (Type-DS-1A) DS-G-G-04 (Location PHE Shaft), sigle leaf, size 600mm x 1800mm, with 35mm thick sand stone cladding on outer face, SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset heavy duty hinges (suitable to take additional load of sand stone) size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.16.21 Door (Type-DS1) DS-G-G-05 (Location : FF + HVAC Shaft), sigle leaf, size 900mm x 1800mm, with 35mm thick sand stone cladding on outer face, SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing offset heavy duty hinges (suitable to take additional load of sand stone) size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle

7.16.22 Door (Type-10) D-G-1F-07 (Location : Landscape service, single equal leaf, size 900mm x 1800mm, with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Cylindrical lock with knobs and key opening

c) Surface door closer, Medium duty EN 2-4 with std arm, Silver finish - 1 No. (on one leaf)

d) Concealed Flush Bolt L=300mm - 1 No. (on other leaf)

e) Lever Handle

7.16.23 Door (Type-DS1) DS-J-L-05 (Location: FF Shaft), size 900mm x 2400mm, with single leaf door shutters with fire rated SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle from outside

7.16.24 Door (Type-6) DS-J-2F-04 (Location: FF Shaft), size 900mm x 2400mm, with single leaf door shutters with 12mm thick Plywood backing on one side of the door finish with approved 4mm thick veneer finish with fire rated SS hardware of approved make Nos 2.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle from outside

7.16.25 Door (Type-DS1) DS-J-1F-10 (Location : FF Shaft), sigle leaf, size 900mm x 2400mm, with 12mm thick Plywood backing on one side of the door finish with approved 4mm thick veneer finish with SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 3 Nos.

b) Allen key Dead lock

c) Concealed handle from outside

7.16.26 Door (Type-DS2) DS-J-3F-01 (Location Fire Shaft), size 900mm x 1500mm, with double equal leaves door shutters (450mm + 450mm) with fire rated SS hardware of approved make Nos 1.00 0

a) 5 Knl, Ball bearing hinges size 100 x 75 x 3mm, SSS - 6 Nos.

b) Allen key Dead lock, suitable for double leaf

7.18 Designing, providing, fixing electrically operated galvanized rolling shutters made from nominal 75mm wide interlocking laths. Sections of minimum 18 gauge. Shutters are divided for opening as per detailed. Further to include endlocks, windlocks and angles at bottom of curtain, curtain guides, hood etc. all of G.I. and roller shaft, counterbalance balance mechanism, brackets of steel all anti - corrosion treated. Mechanism to operate with electrical motors at rate of approximately 300mm/sec. Further to have arrangement for manual operating by crane / chain in case of power failure.

7.18.1 GI Shutters non-perforated fire rated RS-A-1F-01 size 2500mm x 5900mm (motor operated) (Location : RS Gaurav Gal) Nos 1.00 0

7.18.2 GI Shutters non-perforated fire rated RS-B-1F-01 size 3100mm x 5900mm (motor operated) (Location : Fire COMPRT RS) Nos 1.00 0

7.18.3 GI Shutters 80% perforated fire rated RS-C-L-01 size 1800mm x 2100mm (motor operated) (Location : Waste Management) Nos 1.00 0

7.18.4 GI Shutters Single skin non-insulated fire rated RS-C-L-02 size 1800mm x 2100mm (motor operated) (Location : Loading bay) Nos 1.00 0

7.18.5 GI Shutters Single skin non-insulated fire rated RS-G-L-01 size 3000mm x 3600mm (motor operated) (Location : Fire CMPRT RS) Nos 1.00 0

7.18.6 GI Shutters 80% perforated RS-J-B-01, RS-J-B-02 size 4000mm x 3250mm (motor operated) (Location : LT panel, DG) Nos 2.00 0

7.18.7 GI Shutters 80% perforated RS-J-B-03, RS-J-B-04 size 4000mm x 5200mm (motor operated) (Location : DG) Nos 2.00 0

7.18.8 GI Shutters Single skin non-insulated fire rated RS-J-L-01 size 4500mm x 4800mm (motor operated) (Location : Fire rated Comparatmentalization) Nos 2.00 0

7.18.9 GI Shutters 80% perforated RS-J-L-02, RS-J-L-03 size 2400mm x 2100mm (motor operated) (Location : Gas bank) Nos 2.00 0

7.18.10 GI Shutters 80% perforated RS-J-L-04, size 3550mm x 2100mm (motor operated) (Location : Gas bank) Nos 1.00 0

7.18.11 GI Shutters Non perforated RS-K-G-01, size 2725mm x 1800mm (motor operated) (Location : RS ticketing counter) Nos 1.00 0

7.18.12 GI Shutters 80% perforated RS-K-G-02,03, size 1400mm x 1800mm (motor operated) (Location : RS clock room) Nos 1.00 0

7.19 Providing, fabricating and fixing in position Thresholds below doors as per A-13 series drawings, schedules in A-13-15 & 16 and as detailed in drawing A-13-20, made out of Stainless steel 304 grade plates, angles as per drawing to the entire satisfaction of the EIC.

7.19.3 Type-3A Rmt 48.45 0

7.19.4 Type-4 with EPDM rubber seal gasket Rmt 54.00 0

7.19.5 Type-4A with EPDM rubber seal gasket Rmt 5.40 0

7.19.7 Type-5A Rmt 4.34 0

7.19.9 Type-6A Rmt 16.20 0

7.20 Supply and installation of approved Titanium Alloy Roofing sheet having 25/430mm sheet profile STANDING SEAM ROOFING SYSTEM IN 0.7mm THICK Zinc. Titanium Alloy comprising of the followings (Drawing no-A12-09 & 15/A14-01) Sqm 2,098.00 0

Top layer – Zinc titanium Alloy standing seam profiled panels 25 /430 (25 mm seam height & 430mm panel width) manufactured from zinc titanium alloy in 0.7mm miniumum thickness having Quartz Plus finish for Roofing application. The material properties shall be as follows: Ultimate tensile strength: minimum 150 N/mm2,0.2% Proof Stress: min 100 N/mm2, Modulus of elasticity: 90,000 N/mm2 Panels shall be fixed to the substructure using Stainless Steel clips fixing & sliding clips of suitable height with spacing as required for the wind loads. The roofing sheets shall be as per EN 988 standards. The zinc roof sheets shall have a protection on its underside consisting of a 60 micron thick composite acrylate-urethane protective coating.

Second Layer: Synthetic Mesh - Anti Abrasive breathable membrane to be laid underneath the Zinc

Third Layer : 1.0 mm thick GI strips to place at distance of 330 to 430 mm for fixing of clips

Fourth Layer 0.47mm TCT Hi-Tensile steel sheets profile with nominal 3 to 4mm deep ribs at pitch of nominal 50 to 55mm centre to centre distance 550 MPa Yield Strength. The decking sheet shall be fixed over the galvanized steel Hat Section using

Fifth Layer : Z GIRT: Sub girt in Z-section 1.6mm thick in galvanised steel fixed to steel purlins through

Sixth Layer : Insulation layer – Rockwool Insulation of overall thickness 100mm with 60Kg/m3 density

Insulation shall be with one side Aluminum foil to act as vapor barrier

Rate also inclusive of supply & fixing of zinc flashing having girth upto 200mm comprising of following layers, i) First Layer - Zinc Titanium Alloy flashing manufactured from zinc titanium alloy in 0.7mm minimum thickness having Quartz plus surface Finish, ii) Second Layer - Synthetic mesh - Anti abrasive breathable membrane laid underneath the zinc flashings, iii) Third Layer - Galvanized Steel continuous stiffener having 0.8mm thickness along the length of flashing for support.

7.21 Supply and installation of A1 fence UNICON sheild 3510 anti climb welded mesh modular fence system in thermoplastic powder coating (colour-antracite grey RAL 7016) with Y-arm and SS 316 concertina coil razor blade tape.the fincing is fixed over the RCC foundations at a regular interval of spacing 2.5 mter c/c. Complete as directed. Vendor to submit shop drawing. Rmt 443.00 0

7.22 Providing and fixing in position 40x40mm and 10 guage GI chainlink with 50x50x6mm GI angle & 15 mm wide 3mm thk GI flat & 50x50x3.6 mm GI bos section for verticle suppoty etc as per detailed drawing including streatching, fixing with necessary holdfast for every verticle supports, hooks, nuts , bolts, washers and applying 1 coat of primer and 2 coats of epoxy paint of approved make, shade & colour etc. complete as directed. Rmt 431.00 0

TOTAL OF STEEL WORK 0

8. ROOFING & CEILING

The rates quoted by the Contractor for items under this head shall be inclusive of the following:

a) Designing and fixing suspension system including edging angles, accessories etc. for reflected false ceiling drawings to be prepared and got approved based on concept Architectural and Services drawings.

b) Finishing with Gypsum wherever specified.

c) Providing and doing arrangement to receive light fittings, fixtures, A.C. grills, diffusers etc.

d) Ceiling to be paid as per area in plan only. Also for circular, elliptical ceilings / lighting troughs shall determine for areas.

f) Cost of ceiling also to include providing grooves at junctions of Gypsum & all other places wherever required as per instructions of PM.

g) Rate to include all cutting and everything else necessary to complete the work

h) Rate shall include all materials including wastages, labour, tools and plants etc. Also including required scaffolding if any.

i) Work at all heights and leads including required staging, scaffolding etc. No extra rate for height shall be paid

j) Cost of ceiling to include cost of lighting troughs, coffers, pattas, verticals, grooves etc complete. Cost also to include Cornices of various profile as shown in drawing, on verticals of lighting troughs also flat verticals.

k) Pressed GI metal sections in combination of GI wire/section hangers are fixed with anchor fasteners to ceiling providing basic hanging and suspension frame work. These are readily available or may be specially fabricated to suit site requirement.Grid shall be adjusted to suit other requirements to approval of the PM.

l) Finished area shall be measured for payment. No deduction will be made for openings/cut outs upto 0.5 sq.m

m) All the additional supports required for grils, light fittings etc. for strengthening shall be included in the quoted rate and no extra shall be paid. The measurement shall be for the surface area.

8.1 Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanized in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm dia 40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm dia x 230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer In Charge but excluding the cost of painting with : (Refer- CODE-A12-07 & 1/A14-04)

8.1.1 a) 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part I. Sqm 4,469.00 0

8.1.2 Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 13 % perforated area with perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer's pecification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60 (Punch gypsum board acoustic backing) (Refer-A12-07 & 3/A14-04) Sqm 963.00 0

8.1.3 1. 12.5mm thk Glass reinforced Gypsum perforated Acoustic Boards of approx. (1200 X 2500) OR (1200 X 600) sizes. Perforations of 8mm @ 18mm c-c recommended : Knauf Danoline Solopanel Q8/18 square 8x8mm perforations at 18mm c-c 2. GI framework to hold treatment composition. Framework. Saint Gobain Gypserra or similar standard 3. Isolation mount with Sylomer or similar PU based decoupler element. The bottom mount for suspending ceiling below shall have buffer piece between screws. Suspension member shall be aluminium or threaded rod of standard gauge. (Getzner Akustik 1+ Sylomer 30/ GERB or similar ) 4. Melamine foam 50mm approx. 32-40 kg/cu.m density OR FR PU foam (Bassotect G OR Astroforme or similar) 5. 15mm Elastomeric foam applied to the main ceiling slab. Density 180-240 kg/cu.m. FR rated (Kflex Kfonik OR Aramcell RD 230) 6. For Final Finish: Stable substrate, creating a seamless and acoustically monolithic finish on surface. System panel is made of randomly-spun mineral wool with factory-applied and sanded coating of recycled glass granulate, made of 82% natural and recycled materials This system is applied to a stable substrate and finished with post-consumer marble finishes. Standard and custom finishes are available to match any aesthetic or texture, and is available in any custom color. The accessories of fixing, gluing of items shall be considered within the installation process costs. Sampling or mockup of the composition prior to execution shall be provided for approval of relevant authority. Final finish shades or material moodboard shall be made available prior to finalisation. Note: HVAC duct and attenuator details, internal and external insulation types to be clarified with MEP team. (Drg no. A12-07 & 2A/A14-04) Sqm 309.00 0

8.2 Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the Engineer-incharge.(Refer-A12-07 & 2/A14-04)

8.2.1 With 12.5 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) Sqm 3,120.00 0

8.3 Providing and Fixing Channelled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm, made of a Moisture resistant fibre board substrate with a laminated facing as per the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut, Interior White, Alumina Pearl) and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the reverse surface has a “Helmholtz” fluted perforation with consecutive 3mm wide groove followed by 13mm of visible pane. The edges of the panel shall be “tongue-and-grooved” to fix special clips for installation and seamless visual. The back of the perforated panel shall have sound absorbing non-woven Soundtex acoustical fleece hot pressed to achieve NRC of 0.6. (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 and Humidity Resistance (RH) of 70% with camber limit less than 1mm/1000mm and bow less than 1mm/300mm. (Refer-A12-07 & 9/A14-04) Sqm 318.00 0

8.4 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

8.4.1 GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.(Refer-A12-07 & 11/A14-04) Sqm 345.00 0

8.5 Designing, fabricating, testing, installing and fixing in position polyester powder coated Aluminium plank (900mm wide) false ceiling with 3mm thick Aluminium sheet, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing. The item includes cost of all material & labour component, preparation detailed shop drawings with prior approval from Architect, the cost of all mock ups at site etc. complete including preparing shop drawings with prior approval of Architect / Engineer in charge etc. complete. (Refer -A12-07 & 4/A14-04)

8.5.1 Aluminium plank of size : 900mm x 1500mm Location : Ticketing Plaza Sqm 411.00 0

8.5.2 Aluminium plank of size : 450mm x 900mm Location : Driver's Toilet Sqm 20.00 0

8.6 Providing and fixing at all heights and location, acoustic stretched fabric false ceiling system of approved make, comprising of following components and providing NRC of _____ or better, including making cut outs for electrical conduits, networking boxes etc and openings for services and making the same good all complete as per drawings, manufacture's specification and direction of engineer in charge. Frame work : Framework shall be of cold rolled steel as per IS 513, hot dipped galvanised with 120 gsm, zinc coating as per IS 277 (both side inclusive), consisting of ceiling C-channels having web width of 50 mm, equal flanges of 32 mm and sectional thickness of 0.5 mm (+-/0.05 mm), fixed to ceiling with suitable fasteners including providing additional stud channels at openings and junctions as required as well as at locations of vertical grippers. The frame is fixed on 80mm thick plywood partition made out of 15mm thick marine grade plywood fixed on 50mm x 50mm aluminium subframe and 112mm x 50mm high 2nd quality approved teak wood wooden edge. Fabric layer: Fire retardant Fabric in approved shade, colour and texture and having minimum density 200 GSM, conforming to fire class 1 as per BS 476 part 7 and P as per BS 476 part or equivalent, is stretched, tucked and secured into the grippers in maximum possible panel sizes as approved, to obtain smooth, taut & wrinkle-free finish, with the weft and weave of the fabric in all panels oriented in one direction to achieve uniform shade. (Drg-A12-07 & 20/A14-04) Sqm 9.00 0

8.7 Providing, fabricating, and installing decorative wooden slat ceiling system as per drawings and approved details, comprising teak wood beading/slats of specified section (approx. 12 mm thick) fixed over 25×25 mm aluminium framing grid, suspended from structural slab with necessary hangers and supports, including provision of 25 mm thick acoustic board backing (Eckel/Strand, Anutone or approved equivalent) for sound absorption, complete with all required fasteners, anchors, connectors, edge trims, and finishing. The item includes preparation, melamine polishing of wooden members as specified, provision of suspended light fixtures, cutting, wastage, scaffolding, and all incidental works to complete the ceiling in line, level, and true to design, all as directed by the Engineer-in-Charge.(Refer-A12-07 & 10/A14-04) Sqm 159.00 0

8.8 Providing and fixing approved Lightweight Aluminium Access Ceiling Trapdoor as shown in the drawing. The Trapdoor shall be able to carry 12mm painted Gypsum board as per requirement to match the ceiling finish with no visible flange, and just a groove of 2-3 mm visible all around. Fixed to soffit of slab and / or ceiling frame with approved support. The lid to be connected with trap door frame with 1 or 2 Chain with each trap door and locked with 1 or 2 allen keys. The Ceiling Trapdoor shall have one or more openable Lid/Door depending upon the size of trapdoor.

8.9 Providing and fixing roofing of approved designed for installation by mechanically attaching panels to supports using concealed clips and interconnecting side edges of adjacent panels, flashing, ridges, coves, etc. manufactured out of 0.58mm. [total coated thickness (TCT)] siliconised polyester coated cold rolled high strength steel having 275MPa, yield strength sheet to have 150gms/m2 zinc aluminum alloy coating mass or equivalent approved, the weathering surface to be given a finish coat in approved shade and colour, of 20micron SMP paint over 5 micron polyster back coat over 5 micron primer and conversion coat. The rear side to have a neutral backing of epoxy primer coat of 5 micron over 5 micron polyster back coat over 5 micron primer and conversion coat, on covered walk way including insulation & calcium silicate board at bottom, painted with enamel paint system with primer etc. all complete. (Location : Walkway Refer A16-12) Sqm 474.00 0

8.10 Providing, fabricating and fixing Stainless Steel (Grade 316) flashing with 3mm thick sheet with SS (316) subframe including SS screws etc. all complete Sqm 15.00 0

TOTAL OF ROOFING & CEILING 0

9. FINISHING WORK

The rate shall include:

(i) The Plaster shall be of sufficient thickness to fill up all undulations in the surfaces of masonry and to provide a true surface for wall/ceiling plaster. Special care shall be taken to soak the walls before applying the plaster and finishing the surface of plaster to ensure uniform texture and free from air cracks. Before starting the work sufficient Number of button marks shall be done to plumb and level to achieve uniform finish

(ii) Plastering to be done either vertical face, horizontal face or angular face. Rate shall include circular /semicircular or any other shape of the faces of plastering area.

(iii) External plastering works to be inclusive of addition of integral waterproofing compound of approved make with 100 % virgin polypropylene fibrillated fibres of approved make

(iv) The contractor shall make good all the grooves, pockets etc. after the scaffolding is removed.

(v) For POP / Gypplaster items, Work to be executed after making POP level markers at every 1 metres.

(vi) The rate for all types of plaster / Punning given below should be inclusive of the following items

(a) Providing GI Chicken mesh, over lapping to a width of 150 mm at the junctions of masonry and concrete works on either side including tying in position by using suitable nails / clamps / screws and as directed etc. complete at all levels

(b) Forming of drip mould/ bands, grooves of sizes as required etc,. wherever grooves are to be provided horizontally/ vertically for in accordance with the drawings.

(c) Cost of All material and labour

(d) Hacking concrete surfaces to be plastered or rendered

(e) Preparation of surfaces by raking out joints, wetting the surface etc.,

(f) Work at all heights, levels and situations.

(g) Washing floors, cleaning glass and leaving premises clean and tidy after the plastering is done. Disposing off the debris outside the site

(h) Curing the same.

(i) Providing necessary scaffolding, ladder, platform for any height and depth and removing the same after the work is completed

(j) Neat finishing of junctions of plaster and skirting

(k) Screening and washing approved fine aggregates

(l) A 10mm groove to be made with a wooden mould at the joint of ceiling and punned wall.

9.1 Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) Sqm 48,395.00 0

9.2 Providing 20 mm thick double coat mala cement plaster on brick / concrete work for plastering comprising of base coat of 12 mm thick cement plaster in cement mortar (1 Cement : 4 coarse sand) in rough finishing and 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 Coarse sand) finished with trovel including scaffolding curing etc. complete. Sqm 23,701.00 0

9.4 Extra over item 9.1 for providing and mixing water proofing materials in cement mortar in proportion recommended by the manufacturer Kg 6,120.00 0

9.6 Extra for addition of synthetic Polyester triangular fibre of length 6mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement plaster/mortar by using 125 gms. of synthetic Polyester triangular fibre for 50 Kgs. cement used in cement mortar as per directions of Engineer-in-Charge. Kg 771.00 0

9.7 Applying two coats of putty & two coats of primer of approved brand and manufacture on new wall surface to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth. Sqm 18,761.00 0

9.8 Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth Sqm 18,761.00 0

9.9 Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete. Sqm 2,400.00 0

9.10 Finishing wall with water proofing cement paint of on wall surfaces (Two coats) to give an approved brand and manufacture and of required shape even shade after thoroughly brushing the surface to remove all dirt and remains of loose powered materials. Sqm 8,715.00 0

9.11 Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete Sqm 5,659.00 0

9.12 Supply and installation of ISOLATEK vermiculite cement based and ready - mix spray applied fireproof coating thickness shall be used to provide 120 mins of fire protection to structural steel members when tested in accordance with BS 476 part 20/21 or UL 263,ASTM E119 standards . Rate shall be inclusive of preparation of surface, application as per manufacturer's instructions, scaffolding & staging for height of 6m as required etc. complete. Sqm 16,316.00 0

9.13 Supply and installation of low VOC water based Intumescent ISOLATEK WB3 coating as a fire protective treatment with coating thickness shall be designed to provide minimum 120 mins of fire protection to structural steel members consisting portal rafter and columns when tested in accordance with BS 476 part 20/21 or UL 263,ASTM E119 standards. The fire protection system shall consist of base coat(primer)fire protection coating (water based intumescent) and finish topcoat (polyurethane). Rate shall be inclusive of preparation of surface, application as per manufacturer's instructions, scaffolding & staging staging for height of 6m as required etc. complete. Sqm 10,567.00 0

9.14 Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. Sqm 500.00 0

TOTAL OF FINISHING WORK 0

10. ALUMINIUM WORK

Aluminum Windows with glass work

All work should be carried out as per specifications and drawings (refer A-13 drawings)

The rate shall include the following, in addition to the “Measurement / Rate “ as mentioned in Technical specification:

a) All materials with wastage

c) Designing, preparing shop drawing, fixing and erecting aluminium windows with heavy duty aluminium sections anodize coating as per actual site measurement

d) Aluminum alloy - IS 733

e) Extrusion - HE9WP (IS 63400 WP)

f) Fabrication and transport

g) EPDM or Neoprene Gaskets

h) Stainless steel fasteners for exposed condition and stainless steel or cadmium plated fasteners for concealed conditions.

i) Stainless steel fixtures

l) Visual Mock-ups

n) Installation

p) Warranty for 10 years on Rs. 100/- stamp paper

q) Fittings and fixtures shall be as specified in BOQ and shall be included in quoted rates

r) Run of silicon sealants around junction

s) All glass to be Low Iron (Extra clear) and be tempered (toughened)

t) All exterior glass to be DGU of adequate glass thickness with 18 mm spacer.

u) All exterior glass to have low e coating on the inner surface of exterior glass to be (Saint Gobain SKN 183 or equivalent ) Low E- coating Glass with VLT >65% & SHGF <0.4.

v) The rate shall include providing and fixing fire barrier

- Aluminium sections shall be of approved premium brand

- All fixing shall be concealed

- EPDM beading purpose made shall be provided.

- Chromotised sub frame to be fixed prior to plaster.

- EPDM gasket shall comply with 11149:1984

- Fixing shall be with SS screws.

- All beading shall be snap on type.

- Glazing beading shall be from inside only.

- Extruded sections shall comply with IS 733 ; 1956

- Hollow sections shall comply with IS 1285 : 1958

Casement Windows (Factory fabricated)

- Hinges shall be strong and with Stainless Steel pin and washers.

- Two way locking arrangement.

- Handles shall be strong / durable and finished as of aluminum.

- In fixed glazed, extruded snap-on type beading shall be provided.

- Friction stay or as approved shall be used of Stainless Steel.

- where specified lever locks shall be provided

Sliding Windows. (Factory fabricated)

- Anti-lifting device.

- Bottom rail shall be with self cleaning gutter section.

- Stainless steel ball bearings rollers.

- Concealed locking arrangement.

- Concealed tower bolts.

- All fitting and fixtures such as lever locks, handles, hinges, concealed tower bolts, etc. shall be suited to sections and be of approved make. They shall be finished in matching powder coating. Stainless steel (304 grade) Mosquito mesh of required aperture and 26 gauge with minimum 60 micron powder coated aluminium framing with prior approval before installation.

- Supply and fixing of aluminium work shall be carried out from approved agency.

- Prior to start of work supplier shall submit detailed full scale shop drawings including plan, elevation and detail of fixing with structure for approval of the PM. Samples of each item on full scale or smaller scale as directed by the PM shall be submitted for approval.

- Work shall proceed only on approval of shop drawing, samples of each extruded section, beading, gaskets, wool pile, fittings and fixtures by the PM in writing.

- Glazing shall be as noted for each unit in drawing.

- Mockup of specified samples by architects to be carried out at no extra cost.

Fixed window (Type-1)

10.2.1 W-L-G-01 of size 1095mm x 1200mm with Single pane 8mm Sqm 2.00 0

10.2.2 W-N-G-01 of size 600mm x 1200mm with Single pane 8mm Sqm 1.00 0

10.2.3 W-V-G-01 of size 450mm x 1050mm with Single pane 8mm Sqm 1.00 0

10.2.4 W-FS-G-01 of size 1350mm x 1050mm with Single pane 8mm Sqm 2.00 0

10.2.5 W-FS-G-02 of size 600mm x 1050mm with Single pane 8mm Sqm 1.00 0

10.2.6 W-C-1F-02A of size 1200mm x 1200mm with DGU glass type # 4: Insualted (8mm + 16mm +6mm) 30mm Sqm 2.00 0

Fixed window (Type-9)

10.2.7 W-A-G-09 of 600mm x 2400mm DGU glass type # 1: Inuslated (6mm + 1.5mm Laminate + 6mm + 16mm Air Gap + 8mm) 37.52mm Sqm 2.00 0

10.2.8 W-K-G-01 of size 2725mm x 1000mm DGU glass type # 4: Insualted (8mm + 16mm +6mm) 30mm Sqm 3.00 0

10.2.9 W-K-G-02 of size 1400mm x 1000mm DGU glass type # 4: Insualted (8mm + 16mm +6mm) 30mm Sqm 4.00 0

10.2.10 W-L-G-02 of size 1800mm x 950mm with Single pane 8mm Sqm 2.00 0

10.2.11 W-N-G-02, W-FS-G-02 of size 1350mm x 1000mm with Single pane 8mm Sqm 4.00 0

10.2.12 W-V-G-02 of size 1800mm x 1050mm with Single pane 8mm Sqm 2.00 0

Fixed Folding Window at 90° Window (Type-18A)

10.2.13 W-L-G-03 of size 2250mm x 1200mm with Single pane 8mm Sqm 3.00 0

Fixed Window (Type-23)

10.2.14 W-G-1F-21 of size 3900mm x 3000mm DGU glass type # 1: Inuslated (6mm + 1.5mm Laminate + 6mm + 16mm Air Gap + 8mm) 37.52mm Sqm 12.00 0

Fixed Window (Type-26)

10.2.15 W-J-4F-04 of size 15850mm x (1900mm at LHS + 2773mm at RHS) DGU glass type # 1: Inuslated (6mm + 1.5mm Laminate + 6mm + 16mm Air Gap + 8mm) 37.52mm Sqm 38.00 0

Fixed Window (Type-27A)

10.2.16 W-G-L-14 of size (1200mm at bottom + 1620mm at top) x 2400mm DGU glass type # 1: Inuslated (6mm + 1.5mm Laminate + 6mm + 16mm Air Gap + 8mm) 37.52mm Sqm 4.00 0

10.3 Designing, fabricating, testing, installing and fixing in position 5mm thick Aluminium sheet cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing. The item includes cost of all material & labour component, preparation detailed shop drawings with prior approval from Architect, the cost of all mock ups at site, cleaning and protection of cladding till the handing over of the building for occupation. Base frame work for cladding is payable under the relevant aluminium item. Refer A14-02 Det - 12 Sqm 36.00 0

10.4 Providing and fixing 2mm thick Aluminium flashing about 100mm wide with necessary accessories as shown in drawing. (Refer-A12-08 & details A11-01 5/6/7/7A

TOTAL OF ALUMINIUM WORK 0

11 PLUMBING WORKS

11.1 SANITARY & PLUMBING FITTINGS / FIXTURES

11.1.1 Supply, Fixing, testing & commisioning of selected kohler make white coloured wall mounting european water closet (EWC), PVC seat cover, Pan connector with 'P' trap outlet with rubber buffers, flap, CP hinges, CP bolts and nuts, all of approved make etc., complete, including cutting and making good the walls and floors wherever required. (For FOH toilet) EWC (KOHLER Vive Wall-hung round-front toilet with skirted trapway, dual-flush K- 28780IN-0 or equivalent approved) Nos 84.00 0

11.1.2 Supply, Fixing, testing & commisioning of selected laufen make white coloured wall mounting european water closet (EWC), PVC seat cover, Pan connector with 'P' trap outlet with rubber buffers, flap, CP hinges, CP bolts and nuts, all of approved make etc., complete, including cutting and making good the walls and floors wherever required. (For VIP toilet) EWC (LAUFEN PRO WALL HUNG -8.2096.6.000.000+8.9896.6.000.000.1) SIZE : 355 x 545 mm (RIMLESS) Nos 3.00 0

11.1.3 Supply, Fixing, testing & commisioning of selected jaquar make white coloured wall mounting european water closet (EWC), PVC seat cover, Pan connector with 'P' trap outlet with rubber buffers, flap, CP hinges, CP bolts and nuts, all of approved make etc., complete, including cutting and making good the walls and floors wherever required. (For BOH toilet) EWC (JAQUAR - Opal Prime - OPS-WHT-15953BIUFPM - With UF Soft Close Seat Cover) Size: 370x510x360 mm Nos 20.00 0

11.1.4 Supply, Fixing, testing & commisioning of selected jaquar make white coloured orissa pan (IWC) with S/P trap, including cutting and making good the walls and floors wherever required. For FOH & BOH toilet) Indian WC (JAGUAR ECS-WHT-455, 450X535X180 mm) Nos 17.00 0

11.1.5 Supply, Fixing, testing & commisioning of selected kohler make white coloured wash hand basin with CP hinges, CP bolts and nuts, all of approved make etc., complete, including cutting and making good the walls and floors wherever required. (For FOH toilet) WASH BASIN (KOHLER 2215IN-2-0 Ladena Undercounter Basin In White) SIZE : 581 X 402 mm (UNDER COUNTER) Nos 61.00 0

11.1.6 Fixing, testing & commisioning of selected laufen make white coloured wash hand basin with CP hinges, CP bolts and nuts, all of approved make etc., complete, including cutting and making good the walls and floors wherever required. (For VIP toilet) Nos 3.00 0

11.1.7 Supply, Fixing, testing & commisioning of selected jaquar make white coloured wash hand basin with CP hinges, CP bolts and nuts, all of approved make etc., complete, including cutting and making good the walls and floors wherever required. (For BOH toilet) Nos 23.00 0

11.1.8 Supply, Fixing, testing & commisioning of selected kohler make white coloured urinal with inbuilt sensor, including CP hinges, CP bolts and nuts, all of approved make etc., complete, including cutting and making good the walls and floors wherever required. (For FOH toilet) Nos 61.00 0

11.1.9 Supply, Fixing, testing & commisioning of selected roca make white coloured urinal with inbuilt sensor, including CP hinges, CP bolts and nuts, all of approved make etc., complete, including cutting and making good the walls and floors wherever required. (For VIP toilet) Nos 2.00 0

11.1.10 Supply, Fixing, testing & commisioning of selected jaquar make white coloured urinal with CP hinges, CP bolts and nuts, all of approved make etc., complete, including cutting and making good the walls and floors wherever required. (For BOH toilet) Nos 8.00 0

11.1.11 Supply, Fixing, testing & commisioning of selected generic make SS Sink with CP hinges, CP bolts and nuts, all of approved make etc., complete, including cutting and making good the walls and floors wherever required. (For Break Room) Nos 17.00 0

11.1.12 Supply, Fixing, testing & commisioning of selected schell make flush valve with flush plate for EWC, including cutting and making good the walls and floors wherever required. (For FOH VIP, BOH & Admin toilets) Nos 124.00 0

11.1.13 Supply, Fixing, testing & commisioning of selected jaquar make sensor concealed type flush valve with flush plate for urinal, including cutting and making good the walls and floors wherever required. (For FOH & BOH toilets) Nos 69.00 0

11.1.14 Supply, Fixing, testing & commisioning of selected jaquar make sensor concealed type flush valve with flush plate for urinal, including cutting and making good the walls and floors wherever required. (For VIP toilets) Nos 2.00 0

11.1.15 Supply, Fixing, testing & commisioning of jaquar make C.P. two way bib cock with C.P. wall flange, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. (For FOH, VIP & BOH toilets) Nos 107.00 0

11.1.16 Supply, Fixing, testing & commisioning of jaquar make C.P. health faucet, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. (Health Faucet shall be with 4 lpm PCA insert) (For FOH, VIP & BOH toilets) Nos 107.00 0

11.1.17 Supply, Fixing, testing & commisioning of jaquar essco make C.P. bib cock with C.P. wall flange, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. (For FOH, BOH & Admin toilets & AHU) Nos 37.00 0

11.1.18 Supply, Fixing, testing & commisioning of jaquar make C.P. sensor faucet table mounted with 450 mm long copper pipes and brass nuts, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. (WHB Faucet shall be with 2.5 lpm PCA areator) (For FOH toilets) Nos 61.00 0

11.1.19 Supply, Fixing, testing & commisioning of jaquar make C.P. sensor faucet table mounted with 450 mm long copper pipes and brass nuts, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. (WHB Faucet shall be with 2.5 lpm PCA areator) (For BOH toilets) Nos 23.00 0

11.1.20 Supply, Fixing, testing & commisioning of jaquar make C.P. sensor faucet table mounted with 450 mm long copper pipes and brass nuts, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. (WHB Faucet shall be with 2.5 lpm PCA areator) (For VIP toilets) Nos 3.00 0

11.1.21 Supply, Fixing, testing & commisioning of jaquar make C.P. sink cock with swinging spout, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. (Sink Faucet shall be with 6 lpm PCA aerator) (For janitor room sink) Nos 17.00 0

11.1.22 Supply, Fixing, testing & commisioning of jaquar make C.P. angular stop cock, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. (For FOH, VIP & BOH toilets & kitchens, water fountain boiler provision) Nos 167.00 0

11.1.23 Supply, Fixing, testing & commisioning of jaquar make C.P. waste coupling, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. (For FOH, VIP & BOH toilets) Nos 87.00 0

11.1.24 Supply, Fixing, testing & commisioning of jaquar make C.P. 32mm bottle trap, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. (For FOH, VIP & BOH toilets) Nos 87.00 0

11.1.25 Supply, Fixing, testing & commisioning of geberit make P.P. 40mm P trap, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. (For janitor room sink) Nos 17.00 0

11.1.26 Supply, Fixing, testing & commisioning of jaquar make concealed body for single lever diverter, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. Nos 4.00 0

11.1.27 Supply, Fixing, testing & commisioning of jaquar make single lever diverter exposed parts kit, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. Nos 4.00 0

11.1.28 Supply, Fixing, testing & commisioning of jaquar make round shape overhead shower, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. Nos 4.00 0

11.1.29 Supply, Fixing, testing & commisioning of jaquar make shower arm, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. Nos 4.00 0

11.1.30 Supply, Fixing, testing & commisioning of jaquar make bathtub spout, including jointing material M-seal, glue, Teflon tap, with necessary fittings and making good the damages etc. complete. Nos 4.00 0

11.1.31 Supply, Fixing, testing & commisioning of racold make electric operated hot water storage type boiler 35 lits capacity with required safety valve, 2 nos 15mm dia metal reinforced flexible connectors 300mm long. boiler shall carry min 5 kg/cm2 pressure. (For Shower) Nos 4.00 0

11.1.32 Supply, Fixing, testing & commisioning of racold make electric operated hot water storage type boiler 50 lits capacity with required safety valve, 2 nos 15mm dia metal reinforced flexible connectors 300mm long. boiler shall carry min 5 kg/cm2 pressure. (For VIP Kitchen) Nos 1.00 0

11.1.33 Supply, Fixing of nirali make C.P. cockroach Trap with perforated cover with required jointing materials for WHB, sink & other area floor traps. Nos 226.00 0

11.1.34 Supply, Fixing of chilly make CP cockroach Trap with plain cover with required jointing materials for urinals. Nos 33.00 0

11.1.35 Supply, Fixing of chilly make CP Cleanout with plain cover with required jointing materials for drain pipe of size: 75mm. Nos 249.00 0

11.1.36 Supply, Fixing of chilly make CP Cleanout with plain cover with required jointing materials for drain pipe of size: 110mm. Nos 232.00 0

11.2 INTERNAL & EXTERNAL WATER SUPPLY 0.00

11.2.1 Providing laying and jointing in true line and level U.P.V.C. Pipe (SCH-40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. (For tanker water supply line from external to UGR) 0.00

11.2.2 Providing laying and jointing in true line and level U.P.V.C. Pipe (SCH-80) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. (For hydromatic / booster domestic, flushing & HVAC water supply downtale & loop upto toilet block, dewatering sump delivery line from sump to external chamber & borewell water supply line from external to UGR) 0.00

11.2.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (SDR-11), having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (For toilet internal piping from shaft to fixture) 0.00

Internal work - Exposed on wall 0.00

11.2.3.1 15 mm nominal dia Pipes Rmt 357.00 0

11.2.3.2 20 mm nominal dia Pipes Rmt 266.00 0

11.2.3.3 25 mm nominal dia Pipes Rmt 225.00 0

11.2.3.4 32 mm nominal dia Pipes Rmt 231.00 0

11.2.3.5 40 mm nominal dia Pipes Rmt 323.00 0

11.2.3.6 50 mm nominal dia Pipes Rmt 146.00 0

11.2.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (SDR-11), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. For toilet internal piping from shaft to fixture) 0.00

Concealed work, including cutting chases and making good the walls etc. 0.00

11.2.4.1 15 mm nominal dia Pipes Rmt 415.00 0

11.2.4.2 20 mm nominal dia Pipes Rmt 452.00 0

11.2.4.3 25 mm nominal dia Pipes Rmt 114.00 0

11.2.4.4 32 mm nominal dia Pipes Rmt 218.00 0

11.2.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (SDR-11), having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (For toilet internal flushing line) 0.00

11.2.5.1 65 mm nominal dia Pipes Rmt 28.00 0

11.2.5.2 80mm nominal dia Pipes Rmt 8.00 0

11.2.6 Providing & fixing of approved make Insulation to hot water lines of following sizes. Insulation shall be flexible elastomeric thermal insulation of 13mm thk for pipe dia upto 20mm & 25mm thk for pipe dia from 25mm to 50mm & 35mm thk for dia above 50mm. This will be used for toilet internal lines in walls / ceilings. All joints will also be continuously sealed with same material. All insulation should be covered with insulation tape etc. complete, as per direction of engineer in charge. 0.00

11.2.7 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (C-Class) (For corporation water supply line from external to UGR) 0.00

External work 0.00

11.2.7.1 80 mm nominal dia Pipes Rmt 449.00 0

11.2.8 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete (C-Class) 0.00

11.2.8.1 50 to 80 mm nominal bore Nos 1.00 0

11.2.9 Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately). Nos 1.00 0

11.2.10 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 0.00

11.2.10.1 25 mm nominal bore Nos 15.00 0

11.2.10.2 20 mm nominal bore Nos 6.00 0

11.2.10.3 32 mm nominal bore Nos 18.00 0

11.2.10.4 40 mm nominal bore Nos 30.00 0

11.2.10.5 50 mm nominal bore Nos 25.00 0

11.2.11 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 0.00

11.2.11.1 15 mm nominal bore Nos 63.00 0

11.2.12 Providing and fixing Gun metal check or non-return fullway wheel valve. 0.00

11.2.13 Providing and fixing gun metal non- return valve of approved quality (screwed end) : 0.00

11.2.13.1 50 mm nominal bore 0.00

11.2.13.1.1 Horizontal Nos 7.00 0

11.2.13.2 65 mm nominal bore 0.00

11.2.13.2.1 Horizontal Nos 2.00 0

11.2.13.3 80 mm nominal bore 0.00

11.2.13.3.1 Horizontal Nos 11.00 0

11.2.14 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 0.00

11.2.15 Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 0.00

11.2.16 Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications. 0.00

Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified. 0.00

11.2.17 Providing, fixing, testing & commisioning of approved make GM Air Release Valve ISI marked, including flanges / union, nuts, bolts, washer etc., complete as required. All valves shall be (PN-10) pressure rated. 0.00

11.2.18 Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : 0.00

11.2.18.1 80 mm dia nominal bore Nos 1.00 0

11.2.19 Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 0.00

11.2.19.1 25 mm nominal bore, 152 mm long, weighing not less than 440 gms Nos 3.00 0

11.2.20 Providing, fixing, testing & commisioning of approved make diaphragm type Pressure Reducing Brass Valve with filter of PN10 pressure rating, with required flanges, bolts etc. 0.00

11.2.21 Providing, fixing, testing & commisioning of approved make Digital water meter (BMS Compatible) including JT 121PP Sensor With 0.2 Mtr Wire & SS304 threaded end "T" fitting for following sizes. The cost also include all the jointing materials etc., complete as required. 0.00

11.2.21.1 50mm dia. Water pipe connection Nos 2.00 0

11.2.22 Providing, fixing, testing & commisioning of approved make Digital water meter (BMS Compatible) including JT 121PP Sensor With 0.2 Mtr Wire & SS304 stub end with MS flange "T" fitting for following sizes. The cost also include all the jointing materials etc., complete as required. 0.00

11.2.22.1 100mm dia. Water pipe connection Nos 1.00 0

11.2.22.2 150mm dia. Water pipe connection Nos 1.00 0

11.2.23 Providing and fixing approved make Medium duty airtight FRP Manhole cover & frame of following sizes for overhead water tank & dewatering sump with locking arrangements with proper nut bolts fitting, etc. complete. 0.00

11.2.24 Providing and fixing of Expansion Bellows for water supply pipes at pump delivery line for following pipe sizes, including all necessary accessories to make the system complete. 0.00

11.2.25 Providing and constructing B.B. Masonry Chamber of suitable size with cement concrete bedding 150 mm thick grade M-15, with bed projections of 100 mm on each side 150mm thickness, B.B.masonry (200mm) in cement mortor 1:5 with benching from inside with M15 grade C.C. providing 20mm Plastering with cement mortor 1:3 from inside and outside and fixing airtight double seal plain Medium duty FRP recessed covers of following sizes. including curing etc.complete as per direction of the Architect. suitable for following sizes of inspection chambers. providing and fixing 165mm width poly propylene coated steel reinforced foot rest/Rungs, horizontal 300mmc/c, in staggered manner & Vertical distance 600mm. Rates shall be inclusive of cost for escavation in soft soil or hard soil & back filling as per direction of engineer in charge. (For corporation water supply line & rain water tank valve chamber) 0.00

11.2.25.1 900 X 900mm (up to Depth of 600mm) Nos 1.00 0

11.3 INTERNAL & EXTERNAL DRAINAGE & RAIN WATER 0.00

11.3.1 Providing, laying, jointing, testing and commissioning of approved make Agriculture PVC Pipes Confirming to IS 4985:2000 laid in wall / on floor / below ceiling in shortlengths for wash hand basin / kitchen sinks to floor trap, including all required PVC fittings as per IS 7834:1987 such as 45⁰ bend / shoe bend, single Y, 87.5° bend, socket, reducer etc. with materials & labour etc. complete, jointing with approved make solvent cement solution & giving watertightness test for pipes laid in the sunken / ceiling portion with making holes in walls / floor grooving & redoing the same and proper clamp / hangers / pedistal supports wherever required necessary etc. complete, as per direction of engineer in charge. (For wash basin & urinal drain line) 0.00

11.3.1.1 P.V.C. Pipes 6 kgf / Sq.cm. 40mm dia. Rmt 298.00 0

11.3.1.2 P.V.C. Pipes 6 kgf / Sq.cm. 50mm dia. Rmt 120.00 0

11.3.2 Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. Rmt 116.00 0

11.3.2.1 Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with Each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (For toilet internal drain line) Rmt 1,290.00 0

11.3.2.2 Providing, laying and jointing in true line and level 75 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with Each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. (For toilet internal drain line) Rmt 1,246.00 0

11.3.3 Providing, laying, jointing, testing and commissioning of approved make HDPE PIPES and FITTINGS for drainage systems in the dimensions d 32–315 mm in accordance with DIN EN 1519-1- 2000- 1 / DIN EN ISO 11925- 2- 2002 - 07. Discharge pipes made of tempered PE pipes with minimum reset of only 1 % -Density - 0.95 g/cm3 and fittings with smooth ends, for discharge pipes inside and outside buildings... HDPE meets the requirements of EN 12666-1 for buried discharge channels and pipes. HDPE Pipe need to supply along with necessary fittings such as, 45 deg. or 88.5 deg. bends, Tee's, Y's, access pipe and reducers. All pipe to pipe and pipe to fittings should be Butt welded / Electro Fusion Coupling as per requirement and giving water tightness test for the pipes laid in the sunken/ceiling suspended portion with making holes in brick walls/floor grooving & redoing the same and brick support whenever required necessary etc. complete. Laying as per manufacturer guidelines in accordance with DIN EN 1519-1-2000-1/DIN EN ISO 11925-2-2002-07. Including proper clamp / hangers / pedistal supports wherever required necessary etc. complete, as per direction of engineer in charge. (For all internal rain water lines) 0.00

11.3.4 Providing and fixing in position approvaed make 110X75X50mm dia. PVC Multifloor trap 50mm deep seal for embedded areas. Making proper connection with cement solvent joints, cutting chase / hole / core cut in floors / slabs and bringing the same in proper condition and shape after placing the trap in right position etc. complete, as per direction of engineer in charge. Nos 259.00 0

11.3.5 Providing and fixing in position of approved make 110X63mm dia. PVC Boss Connector above the floor trap for wash hand basin / urinals, making proper connection with cement solvent joints, cutting chase / hole / core cut in floors / slabs and bringing the same in proper condition and shape after placing the fitting in right position etc. complete, as per direction of engineer in charge. Nos 3.00 0

11.3.6 Providing & fixing of approved make UV Stabilzed PVC Cowl conforming to IS 14735:1999 for following pipe sizes with all required accessories & jointing materials etc. complete, as per direction of engineer in charge. 0.00

11.3.6.1 PVC SWR Vent Cowl 75 mm dia Nos 7.00 0

11.3.6.2 PVC SWR Vent Cowl 110 mm dia Nos 2.00 0

11.3.7 Providing & fixing of approved make PVC Cleanout Plug for following pipe sizes with all required accessories & jointing materials etc. complete, as per direction of engineer in charge. 0.00

11.3.8 Providing and fixing STUDOR MINI-VENT with global connector, airflow of 7.5 l/s with opening at -70 Pa, operating temparature -40° C to +60° C,one-way vents (AAVs), which resolve any negative transient pressure within a drainage system so it does not influence the water trap seal with required fittings to mount on the piping system with supports to place the unit in position. Exact placement to follow active drainage ventilation brand design guidelines. Nos 36.00 0

11.3.9 Providing and fixing STUDOR MAXI-VENT with global connector, airflow of 32 l/s with opening at -70 Pa, operating temparature -40° C to +60° C,one-way vents (AAVs), which resolve any negative transient pressure within a drainage system so it does not influence the water trap seal with required fittings to mount on the piping system with supports to place the unit in position. Exact placement to follow active drainage ventilation brand design guidelines. Nos 23.00 0

11.3.10 Supply, fixing and commissioing of polyethylene as per DIN EN 1825; proven Stability of 50 years; for below ground installation; overall dia of 1320 mm.; with ventilation provision; emptying via suction line DN 65 PN 10; counter flange with fire hose quick coupling 75B and 2½" blank cap and satisfy reaction to fire Class A15 . Standard odour tight top cover of 600 mm dia. clear opening; frame made of concrete material and cover made of cast iron; with raising tube, load class A15 according to EN 124 Inlet and outlet dia: DN 100 Make: ACO: Model: Lipumax PDNominal Size: NS 2 Grease Storage: 270L , Sludge Trap: 245L , Overall Capacity: 720L Art No: 3202.81.00 + 3300.14.01( With extension Pcs) Nos 1.00 0

11.3.11 Supply, fixing and commissioing of Grease separator made of polyethylene as per DIN EN 1825; proven Stability of 50 years; for below ground installation; overall dia of 1320 mm.; with ventilation provision; emptying via suction line DN 65 PN 10; counter flange with fire hose quick coupling 75B and 2½" blank cap and satisfy reaction to fire Class A . Standard odour tight top cover of 600 mm dia. clear opening; frame made of concrete material and cover made of cast iron; with raising tube, load class A15 according to EN 124 Inlet and outlet dia: DN 150 Make: ACO: Model: Lipumax PDNominal Size: NS 8.5 Grease Storage: 360L, Sludge Storage: 860L, Overall Capacity: 1900L Art No: 3208.81.00 + 3300.14.01 Nos 1.00 0

11.3.12 Supply of Grease separator made of polyethylene as per DIN EN 1825; proven Stability of 50 years; for below ground installation; overall dia of 1320 mm.; with ventilation provision; emptying via suction line DN 65 PN 10; counter flange with fire hose quick coupling 75B and 2½" blank cap and satisfy reaction to fire Class A15. Standard odour tight top cover of 600 mm dia. clear opening; frame made of concrete material and cover made of cast iron; with raising tube, load class A15 according to EN 124 Inlet and outlet dia: DN 150 Make: ACO: Model: Lipumax PDNominal Size: NS 10 Grease Storage: 415L, Sludge Storage: 1010L, Overall Capacity: 2170L Art No: 3210.81.00 + 3300.14.01( With extension Pcs) Nos 1.00 0

11.3.13 Providing and fixing PVC Bottle Gully Traps of size 150 x 100mm Dia in BBM chamber & supported with PCC M15 grade. 0.00

11.3.13.1 PVC SWR Gully Trap 160 x 110 Nos 18.00 0

11.3.14 Providing, lowering & laying including supply of materials and labour for SN4/SN8 Rigid PVC pipe of standard make, with necessary cutting to the required length including short pieces with assorted fittings, Separate coupler with unique design of click ring and rubber – sealing rings upto 250mm (Solvent weld and rubber ring upto 250mm pipe) & above pipe dia. with solution/ push fit jointing, (Solvent weld type coupler for 315mm & 400mm pipe) and giving water tightness test for the pipes laid. All the pipes which will be laid in soil / filling shall be properly supported at all joints, change in dia, direction.etc. works to be executed as per IS complete as per direction of engineer in charge. (For external sewer drain lines) 0.00

11.3.15 Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. (For external storm water line) 0.00

11.3.16 Providing and constructing BBM chamber of size 300 x 300 & cement concrete M15, chamber is smooth finishing from inside & outside with CM 1:3 including FRP recessed grating medium duty cover over the gully trap. Nos 18.00 0

11.3.17 Providing and constructing B.B. Masonry Chamber of suitable size with cement concrete bedding 150 mm thick in 1:6 cement mortar bedding projecting 150mm and benching from inside with 1:2:4 C.C. and plastering with cement mortar 1:3 from inside and outside. Including providing and fixing precast Plain FRP recessed Covers along with frame including providing and fixing C.I. steps 300mmc/c Benching in M15 and finishing with cement punning inside, including curing, excavation etc. complete, as per direction of engineer in charge. 0.00

11.3.17.1 600 X 600mm (up to 450mm depth) (MD Cover) Nos 43.00 0

11.3.17.2 900 X 450mm (up to 450mm depth) (MD Cover) Nos 27.00 0

11.3.17.3 900 X 900mm (up to 1000mm depth) (MD Cover) Nos 36.00 0

11.3.18 Same as item no. 16.0, for chamber depth as below. Rate per meter of chamber. 0.00

11.3.18.1 600 X 600mm (depth above 450mm) Rmt 14.43 0

11.3.18.2 900 X 450mm (depth above 450mm) Rmt 10.31 0

11.3.18.3 900 X 900mm (depth above 1000mm) Rmt 28.52 0

11.3.19 Providing, laying & fixing 150mm dia. sewer trap / master trap (PVC) inside the manhole as per direction of the Site Incharge including making good the damages, if made while fixing the sewer trap etc. complete. Nos 1.00 0

11.3.20 Providing and fixing RCC grating, with angle frame 50 x 50 x 5 to suit the clear span of the gutter,thickness of the perforated cover shall be suitable for below mentioned load application. 0.00

11.3.20.1 Size of trench 300mm wide meadium duty Rmt 619.00 0

11.3.21 Providing and fixing in position of approved make S.S. Dome Type Roof Drain, at the entrance of RWP on terrace with all necessary fittings, making proper connection with cement solvent joints, cutting chase / hole / core cut in floors / slabs and bringing the same in proper condition and shape after placing the in right position complete as per direction of engineer in charge. 0.00

11.3.21.1 Aco HP vertical spigot outlet - Dome grate (75mm outlet) (Article number: 105901) Nos 27.00 0

11.3.21.2 Aco HP vertical spigot outlet - Dome grate (110mm outlet) (Article number: 105902) Nos 20.00 0

11.3.21.3 Aco HP vertical spigot outlet - Dome grate (160mm outlet) (Article number: 105903) Nos 33.00 0

11.3.22 Providing and fixing in position of approved make Roof Corner Outlet with all necessary fittings, making proper connection with cement solvent joints, cutting chase / hole / core cut in floors / slabs and bringing the same in proper condition and shape after placing in right position complete as per direction of engineer in charge. 0.00

11.3.22.1 Aco 2 way roof / balcony outlet (260 x 260 dia, 160mm outlet) (Article number: 155304) Nos 6.00 0

11.3.22.2 Aco 2 way roof / balcony outlet (205 x 205 dia, 110mm outlet) (Article number: 155303) Nos 2.00 0

11.3.22.3 Aco 2 way roof / balcony outlet (170 x 170 dia, 75mm outlet) (Article number: 155300) Nos 1.00 0

11.3.23 Providing and fixing in position of Prefab Polymer Concrete ACO Drain V 100 Multiline Channels as per EN 1433 having following properties a) Compressive strength -96 N/mm2 b) Flexural strength -27N/mm2 c) Water absorption - 0.07% d) Manning's roughness- 0.011. The Channels must be 'V'-profile in shape with integrated edge protection made up of Galvanised Steel with boltless drainlock®grating with anti-shunt 4 no. provision per length. The Channels must also be pre-sloped 1:200 or same invert / variable depth with 500 or 1000 mm length and with tongue and groove joints for interlocking, integrated lip labyrinth sealing for liquid-tight connection to ground line with needed accessories like end cap, end cap with outlet etc. Channels to have anchoring features on the outside wall to ensure mechanical bond to the surrounding bedding material and pavement surface.The Channel gratings are made up of Polypropelene in L500 mm length, suitable for polymer concrete drain channels as per load class A -15, B-125, C250 , D 400, E 600 confirming to EN 1433. The Channels will have the nominal width of 100 mm and invert depth varying between 100-250 mm as per design.Composite plastic PP bar grate Microgrip, anthracite black with patented anti-slip surface structure, slip resistance class R13 according to DIN 51130 type Heelguard with slot width 8mm, inlet cross section 284 cm² / m with TPU snap fit locking and certified for load class B125 as per EN 1433. Rmt 454.00 0

11.3.24 Providing and fixing in position of ACO Mod. Custom Curve Channel without edge infill, SS304- (L9210 of R5305 + L8655 of R5310), W=100, H=200/120 (stepped gradient), with DN110 Hz. outlet, with SS Lockable grate, Slotted Design with Powder coating, LC A15 (pedestrian)- (channel as per ML-V100 profile with bottom angle 140* & SS grate as per V100 PP grate) Set 1.00 0

11.3.25 Providing and fixing in position of Prefab Polymer Concrete Euroline Channels in accordance to DIN EN 1433 with following properties. a) Compressive strength -96 N/mm2 b) Flexural strength -27 N/mm2 c) Water absorption - 0.07% d) Mannings roughness- 0.011. The Channels will be 'V'-profile in shape with screw less locking grating, without slope. The Channels interlocking shall be with tongue and groove joints and are with anchoring features on the outside wall to ensure mechanical bond to the surrounding bedding material and pavement surface. The channels will be with knock-out preform for connection to 110mm pipe, provided with inbuilt bottom outlet suitable for DN 100 and with all range of accessories like end plate / end plate with outlet suitabel for DN 60. The Channel gratings will be made up of ductile iron/ Galv. Steel / Stainless Steel 304/ PP in 500 mm / 1000 mm length suitable as per load class A-15 / B-125 / C-250 confirming to EN 1433. The Channels nominal width will be 98 mm with overall width 118 mm and invert depth of the drain 55 mm as per design. Dimensions : 1000x118x97 (LxWxH ), Height (Composite plastic PP bar grate with Microgrip, anthracite black with anti-slip surface structure, type Heel guard with slot width 8mm, inlet cross section 254 cm²/m and certified for load class A-15 as per EN 1433. Art. No: 319250 / 319251 Rmt 120.00 0

11.3.28 Providing and fixing M.S. fabricated angle bracket of required size in 50x50x50mm double angle for water supply & drainage pipe in shaft. Bracket shall be placed so that there is no wrapping of pipes. Bracket shall be painted with red oxide paint & 2-coat of enamel paint with "U" clamp nut & bolts, grounting in wall / dash fastness etc. complete. Kg 2,681.00 0

11.3.29 Providing and fixing Puddle flanges of required sizes in RCC structures at locations and levels as shown on the drawing, fabricated MS hot dip galvanized finish pipes assembly with 5mm wall thickness upto 65 mm nominal bore pipes and 6 mm wall thickness for 80mm or above diameter pipes welded to 5mm thick square plate of size 3 times the diameter of the pipe. Puddle flanges upto 50mm n.b shall have screwed ends whereas pipes of larger diameters shall be provided with flanges of approved sizes on both ends. Overall length of the puddle flange pipe shall be such that it will project 150mm/200mm on either side of the wall. The average length of the puddle flange shall be maximum 900mm in length. Kg 1,000.00 0

11.4 CIVI WORK FOR PLUMBING SYSTEM 0.00

11.4.1 Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone aggregates 20 mm nominal size) and curing complete excluding cost of formwork in (A) Foundation and Plinth (For pipe PCC) Cum 95.00 0

TOTAL CARRIED OVER TO SUMMARY 0.00

11.5 PHE PUMPING SYSTEM 0.00

11.5.1 Providing & Installing of Vertical Inline pumping system for Direct feeding Domestic water from UGR to Toilets on hydropneumatic VFD system: Control Panel must be PLC based IP55 protection with following features: a. Ammeter for individual pump b. Voltmeter c. Phase Reversal preventer d. Single phase preventer e. Automatic sequence change to ensure equal run time for all pumps. f. Panel diagram to be get approved from electrical consultant before finalization. g. Dry run prevention. h. Overheating indication of pump motor & motor shall trip in case of overheating. i. Panel shall have sufficient potential free contact for BMS compatibility. System shall have pressure transducer for operation of pumps. Pump discharge for each pump, Q = 175 lpm @ head of 65m. No of pumps = 2 working + 1 stand by (All pumps with VFD & All component shall be PN 10) Application: - feeding of Domestic water from UGR to Toilets & OHT filling: (Header diameter is 100 NB). Pump body shall be in CI. Impeller, shaft & all wetted parts shall be in SS 304. Keep Cut in set point as 6.0kg/cm2 & cut off set point as 7.0kg/cm2. Set 1.00 0

'11.5.2 Providing & Installing of Vertical Inline pumping system for Direct feeding Flushing water from STP to Toilets on hydropneumatic VFD system: Control Panel must be PLC based IP55 protection with following features: a. Ammeter for individual pump b. Voltmeter c. Phase Reversal preventer d. Single phase preventer e. Automatic sequence change to ensure equal run time for all pumps. f. Panel diagram to be get approved from electrical consultant before finalization. g. Dry run prevention. h. Overheating indication of pump motor & motor shall trip in case of overheating. i. Panel shall have sufficient potential free contact for BMS compatibility. System shall have pressure transducer for operation of pumps. Pump discharge for each pump, Q = 330 lpm @ head of 65m. No of pumps = 2 working + 1 stand by (All pumps with VFD & All component shall be PN 10) Application: - feeding of Flushing water from STP to Toilets: (Header diameter is 150 NB). Pump body shall be in CI. Impeller, shaft & all wetted parts shall be in SS 304. Keep Cut in set point as 6.0kg/cm2 & cut off set point as 7.0kg/cm2. Set 1.00 0

'11.5.3 Providing & Installing of Vertical inline pumping system for feeding of HVAC Cooling towers (at terrace floor) from UGR: Control Panel must be PLC based IP55 protection with following features: a. Ammeter for individual pump b. Voltmeter c. Phase Reversal preventer d. Single phase preventer e. Automatic sequence change to ensure equal run time for all pumps. f. Panel diagram to be get approved from electrical consultant before finalization. g. Dry run prevention. h. Timer system for start & stop of pumps. (Real time timer) i. Over heating indication of pump motor & motor shall trip in case of overheating. j. Panel shall have sufficient potential free contact for BMS compatibility. System shall have pressure transducer for operation of pumps. Pump discharge for each pump, Q = 110 lpm @ head of 55m. No of pumps = 1 working + 1 stand by (All component shall be PN 10) Application: - feeding of HVAC Cooling towers (at terrace floor) from UGR: (Header diameter is 50 NB) Set 1.00 0

'11.5.4 Providing & Installing of Submersible pumps for UGR & STP pump-room sump water pumping to nearest storm water chamber: Pump discharge for each pump, Q = 200 lpm, at head 15.00 m No of pumps = 1 working + 1 stand by. (Solid handelling:20mm, MOC: CI body, SS304 Impeller) PLC based Control Panel to have following features: a. Ammeter for individual pump b. Voltmeter c. Phase Reversal preventer d. Single phase preventer e. Automatic sequence change to ensure equal run time for all pumps. f. Panel diagram to be get approved from electrical consultant & BMS consultant before finalization. g. Dry run prevention. h. Overheating indication of pump motor & motor shall trip in case of overheating. i. Panel shall have sufficient potential free contact for BMS compatibility. All sump pumps shall be able to work on 2 floats (1st float-high high & high low 2nd float low high & low low) Panel should have IP 55 protected. Note- 1. Provide pump curve with duty point marked on the same. 2. Manifold, NRV & valves on supply & delivery are in vendor supply scope. Manifold shall be in SCH 80 UPVC/C-PVC pipes or GI ‘C’ class pipes. Set 2.00 0

'11.5.5 Providing & Installing of Submersible pumps for transfer of stored rain water from Rain water storage tank: Control Panel must be PLC based IP55 protection with following features: a. Ammeter for individual pump b. Voltmeter c. Phase Reversal preventer d. Single phase preventer e. Automatic sequence change to ensure equal run time for all pumps. f. Panel diagram to be get approved from electrical consultant before finalization. g. Dry run prevention. h. Timer system for start & stop of pumps. (Real time timer) i. Over heating indication of pump motor & motor shall trip in case of overheating. j. Panel shall have sufficient potential free contact for BMS compatibility. System shall have pressure transducer for operation of pumps. Pump discharge for each pump, Q = 250 lpm @ head of 15m. No of pumps = 1 working + 1 stand by (All component shall be PN 10) Application: - Transfer of stored rain water from Rain water storage tank: (Header diameter is 80 NB) Set 1.00 0

TOTAL CARRIED OVER TO SUMMARY 0.00

11.6 Supply, installation, testing and comissioning of Heat pumps. Details as per Annexure 3 of Heat pump Technical Specifications Document. Lumpsum 2.00 0

11.7 Supply, installation, testing and comissioning of SEWAGE TREATMENT PLANT using CAMUS-SBT TECHNOLOGY of 170M3 PER DAY capacity and details and parameters as per Annexure 2 of Technical Specifications Document and STP Schematic Layout Drawing Nos 1.00 0

11.8 Supply installation, testing and commissioning of dometic water treatment plant comprising of Multigrade sand filter and softner Plant accrording to input water quality/analysis. softner plant consisting of FRP tank, filter media, resins, brine tank, piping, isolation valves, instruments supports. The scope shall include interconnection piping, valves, instruments, autoback wash arrangement, Brine preparation tank & agitator platform (Make: FRP), 1 nos. Agitator require capacity and Ventury etc. complete the job ..Scope shall also includes training for operation of staff. Inlet Flow Range : 12 CMT/ Hr. Input Water Hardness : ‐( as per water test report) Output Water Hardness : < 50 PPM MULTI‐ GRADE PRESSURE SAND FILTER:Flow Rate : 12 cum/hr Filter Media : Silica, Pables, Gravels And Quartz Sand Size : 700MM Diameter NOTE- Annexure 1 of Technical Specifications Document for WTP design parameters, rate inclusive of cost of water quality test for input parameters and system details of WTP Nos 1.00 0

11.9 Construction of Percolation Well with all required connections as per detailed design 3mtr dia X 4 mtr liquid depth + invert Level) for catch basin with FRP Heavy duty manhole cover and overflow connection to the nearest drain. Etc. complete. Nos 3.00 0

TOTAL OF PLUMBING WORKS 0

12 FIRE FIGHTING WORKS

12.1.1 Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal gland pack conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. Note: *The head of the pump is selected in a manner so as to give a minimum 3.5kgf/cm2 pressure at the highest/farthest point.

12.1.1.1 2850 lpm at 100 m Head Set 3.00 0

12.1.2 Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal gland pack conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. Note: * The head of the pump is selected in a manner so as to give a minimum 3.5kgf/cm2 pressure at the highest/farthest point. 0.00

12.1.2.1 2850 lpm at 100 m Head Set 1.00 0

12.1.3 Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal vertical inline type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 0.00

12.1.3.1 180 lpm at 100 m Head Set 2.00 0

12.1.4 Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical gland pack confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. 0.00

12.1.4.1 900 lpm at 45 m Head Set 3.00 0

12.2 CONTROL PANELS 0.00

12.2.1 Supply, installing, testing and commissioning of Fully automatic pump starter panel having following drives standby pump (1 No.), Sprinkler (1 No.), hydrant pump (1 No.), jockey pump (2 Nos.), & complete with over current protection Control panel to be made out of 16 SWG CRCA sheet powder coated. Control panel comprise of (a) Fully automatic starter for suitable HP rating with suitable range of overload relay protection with facility of Manual & Auto operation based on pressure switch logic (b) 1 no. voltmeter of range 0.500 `v’, AC 50Hz. supply & voltage selector switch mounted on it. (c) 1no. Ammeter of suitable range, AC 50Hz, supply with ammeter selector switch. (d) 3 no. indicating lamps with requisite protective fuses (a) 1 no. Main MCCB. of required capacity & specification (f) switches for auto manual operation to main pump, jockey pump. All material must be as per IS. Panel Shall be provided with required no. potential free contact for BMS compatibility. Status of all F.F. pumps will be monitored (FF pumping system shall be charged at all time & pumps will operate on pressure setting of pressure transducer.) This panel will be checked & approved by Electrical consultant for the project. First jockey pump will start at drop of 95% of the system pressure, main hydrant will start at 85% of the system pressure & standby pump will start at 65% of drop in system pressure. All electrical & control wiring from panel to pump will be in the scope of panel supplier. Rate of same shall be included in the panel cost. Main electrical supply to FF Pump panel will be in the scope of main electrical vendor. This panel will be checked & approved by Electrical consultant for the project. Vendor to consider the all requisite components / provisions for the IOT based monitoring of Fire Pump & System as per the Fire NOC compliance. (System Pressure, Pump ON/OFF, Historic Data for 12 months etc) Set 1.00 0

12.2.2 Supply, installation, testing and commissioning of DOL starter (ON/OFF switch) for the Booster pump. Set 6.00 0

12.2.3 Supply and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable. 0.00

12.2.4 Supply installing testing & commissioning of G.I. strips for earthing of below sizes. 0.00

12.2.5 Supply & installing below type cable trays with structural supporting as per approved drawing and on floor supporting shall be shall be with structural & RCC pedestals. 0.00

12.2.5.1 450mm X 75 mm Ladder type Rmt 25.00 0

12.2.5.2 100mm X 50 mm perforated type Rmt 30.00 0

12.3 PIPES & ACCESSORIES 0.00

12.3.1 Providing laying, testing & commissioning of 'C' class heavy duty GI Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment (pypkote) with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 0.00

12.3.2 Providing, laying, testing & commissioning of 'C' class heavy duty GI pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 0.00

12.3.2.8 200 mm dia (wall thickness 6.3 mm) Rmt 15.00 0

12.3.2.9 250 mm dia (wall thickness 6.3 mm) Rmt 28.00 0

12.3.3 Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : 0.00

12.3.3.1 Single headed Stainless steel Set 64.00 0

12.3.4 Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : 0.00

12.3.4.1 Single headed Gunmetal Set 15.00 0

12.3.5 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 0.00

12.3.6 Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. Nos 79.00 0

12.3.7 Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 0.00

12.3.8 Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 0.00

12.3.9 Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 0.00

12.3.10 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : 0.00

12.3.10.1 Stainless Steel (Grade 304) Set 158.00 0

12.3.11 Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 0.00

12.3.12 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : 0.00

12.3.12.1 Stainless Steel (Grade 304) Nos 79.00 0

12.3.13 Supply, fixing, testing and commissioning of fire cabinet of size not less than 0.75 x 0.6 x 0.25 mtr made out of M.S. sheet not less than 16 SWG thick having central opening and 4 mm thick glazed acryclic sheet doors (Two nos.) suitably marked on the outside 'with the letters "FIRE HOSE" including necessary locking arrangement and painting in red colour suitable to accommodate, and painted in red along with GI support angles for internal hydrants. Nos 64.00 0

12.3.14 Supply, fixing, testing and commissioning of fire cabinet of size not less than 0.75 x 0.6 x 0.25 mtr made out of FRP sheet not less than 16 SWG thick having central opening and 4 mm thick glazed acryclic sheet doors (Two nos.) suitably marked on the outside 'with the letters "FIRE HOSE" including necessary locking arrangement and painting in red colour suitable to accommodate, and painted in red along with GI support angles for external hydrants. Nos 15.00 0

12.3.15 Supplying and fixing of fire brigade connection of cast iron body with SS 304 male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia GI pipe connection conforming to IS 904 as required : 0.00

12.3.15.1 2 way-100 mm dia G.I. Pipe Set 2.00 0

12.3.15.2 4 way - 150 mm dia G.I. Pipe Set 2.00 0

12.3.16 Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. Set 2.00 0

12.3.17 Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : 0.00

12.3.17.1 Pendent Sprinkler Nos 710.00 0

12.3.17.2 Upright Sprinkler Nos 2,611.00 0

12.3.17.3 Horizontal side wall sprinkler Nos 9.00 0

12.3.17.4 Concealed sprinkler Nos 743.00 0

12.3.17.5 Concealed side wall sprinkler K80 Nos 4.00 0

12.3.17.6 Vertical side wall sprinkler K80 for façade protection Nos 218.00 0

12.3.18 Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. Nos 6.00 0

12.3.19 Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 0.00

12.3.20 Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 0.00

12.3.21 Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 0.00

12.3.22 Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required. Nos 709.00 0

12.3.23 Supply & Installation of approved make brass Ball Valve of PN 16 of following below sizes, with all necessary accessories to make the system complete. 0.00

12.3.24 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 0.00

12.3.24.1 25 mm nominal bore Nos 91.00 0

12.3.24.2 50 mm nominal bore Nos 40.00 0

12.3.25 Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required Nos 38.00 0

12.3.26 Supplying and installation of approved make expansion bellows for pipes for following pipe sizes, including all necessary accessories to make the system complete. (For punp suction & delivery line) 0.00

12.3.27 Supplying and installation of approved make FM & UL approved expansion bellows for pipes crossing expansion joint for following pipe sizes, including all necessary accessories to make the system complete. (For building expantion joints) 0.00

12.3.28 Supplying and installation of Test & drain valve PN 16 including all required accessories for automatic sprinkler testing as complete with necessary accessories as per IS standard. Nos 16.00 0

12.3.29 Supply, installation, testing & commissioning of 25mm dia gun metal air release valves of PN 16 of approved make on the top of wet riser as per standard fire practice, with all necessary accessories to make the system complete. Nos 22.00 0

12.3.30 Supply, installation testing & commissioning of of approved make Flow Meter with required fittings, located at Fire pump house. Flow meter Meter shall be suitable for a pump of 4275 lpm discharge and least count shall not be more than 200 lpm Nos 1.00 0

12.3.31 Supply & Installation of 2 core 1mm2 FRLS red colour armoured cable from each flow switch up to Sprinkler annunciation panel in the basement. Rmt 90.00 0

12.3.32 Supply & Installation of FM & UL approved 32mm Standard Universal Lateral OR Longitudinal Brace Nos 80.00 0

12.3.33 Supply & Installation of FM & UL approved 80mm Standard Universal Lateral OR Longitudinal Brace Nos 137.00 0

12.3.35 Supply & Installation of FM & UL approved 150mm Standard Universal Lateral OR Longitudinal Brace Nos 715.00 0

12.3.36 Supply & Installation of FM & UL approved Universal Structural Attachment 15mm Mounting Hole, EG for bracing. Nos 932.00 0

12.3.37 Supply & Installation of HILTI Safety stud anchor [HST3 M12x115] for bracing. Nos 932.00 0

12.4 FIRE FIGHTING APPLIANCES 0.00

12.4.1 Supply and installation of portable fire extinguishers, ISI marked of following Capacity. 0.00

12.4.1.1 Co2 fire extinguisher (4.5 K.G.) , IS : 15683 : 2018 Nos 14.00 0

12.4.2 Supply and installation of portable fire extinguishers (A,B,C Type powder) with all accessories as per manufacture's specification., IS : 15683 : 2018 0.00

12.4.2.1 6 Kg Capacity Nos 174.00 0

12.4.3 Supply and installation of portable fire extinguishers with all accessories as per manufacture's specification. Capacity 45Ltrs AFFF Foam type Extinguisher trolly mounted. Nos 2.00 0

12.4.4 Supply and installation of fireman axe as per IS 926, made from forged steel with rubber insulated handle, tested to 20,000 volts Nos 1.00 0

12.4.5 Supply and installation of Fire buckets including stand with paint, etc. as complete for sand (9 lit. capacity, Three buckets with stand). Set 1.00 0

12.5 CIVIL ITEMS 0.00

12.5.1 Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. 0.00

12.5.2 Providing and constructing B.B. Masonry Chamber of suitable size with cement concrete bedding 150 mm thick in 1:6 cement mortar bedding projecting 150mm and benching from inside with 1:2:4 C.C. and plastering with cement mortar 1:3 from inside and outside. Including providing and fixing precast Plain FRP recessed Covers along with frame including providing and fixing C.I. steps 300mmc/c Benching in M15 and finishing with cement punning inside, including curing, excavation etc. complete, as per direction of engineer in charge. 0.00

12.5.2.1 900 X 900mm (up to 1000mm depth) (MD Cover) Nos 3.00 0

TOTAL OF FIRE FIGHTING WORKS 0

13. ELECTRICAL WORK

13.1.00 HT CABLES & ACESSORIES

13.01.00 Supply of armoured aluminium conductor, XLPE insulated FRLS cables of following sizes with Cable labeling directly buried underground, laid in built-up trench / cable tray, pulled through embedded conduits / pipe sleeves, cleated to local support etc. including installation of G.I. clamps, cleats, spacers, hardware etc. Cable Trays, excavation & backfilling is included.

13.01.01 3 C x 240sq.mm 11 KV (E) AL XLPE FRLS cable Rmt 1,000.00 0

13.02.00 Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11KV grade as required :

13.03.00 Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11KV grade as required :

13.04.00 Supplying and making straight through cable jointing with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11KV grade as required :

13.05.00 Supply & installation of 100mm x 75mm oval caste iron cable route markers with 350mm MS Angle support of size 25 x 25 x 6mm / 20mm GI Pipe support in 150 x 150 x 150mm PCC block.

13.06.00 Supply, Installation, testing & commissioning of Compact HT-Panel 11KV 630A, 21KA Non-Extensible Compact Vacuum Circuit Breaker in SF6 insulated stainless steel enclosure type with built in control supply arrangement. Panel suitable for termination of power cables through rear bottom entry, cable gland plates and other accessories as per SEB specification. (as per the SLD and technical specifications.) Nos 1.00 0

13.07.00 Supply, Installation, testing & commissioning of Indoor type HT Breaker Panel 11KV 1 nos. 630A, 21KA Non-Extensible Compact Vacuum Circuit Breaker in SF6 Incomer + 2 nos. 630A, 21KA Non-Extensible Compact Vacuum Circuit Breaker in SF6 insulated stainless steel enclosure type with built in control supply arrangement consisting of a. EF / OC Series Relay as outgoing for Transformer feeders. Panel suitable for termination of power cables through rear bottom entry, cable gland plates and other accessories as per SEB specification for substation. (as per the SLD and technical specifications.) Nos 1.00 0

13.08.00 Supply Installation, site testing, commissioning of indoor type, Copper wound, 1600 KVA, 11KV/0.415 kV, Dyn11, Dry type Distribution Transformer with OLTC , Cable End Box on Primary/HV side & Secondary/LV side for termination as per data sheet. Transformer should be manufactured as per I.S. standards (is 2026 part-1 2012, Losses shall be as per latest ECBC norms and Tech. specifications and Data sheet attached. Note: Unloading at site is also included in scope. Note: Control cables from transformer to panel is included in this scope and cables are mentioned separately in cables item. Nos 2.00 0

13.09 Construction of cable chambers with complete supply of brics masonry, chamber covers & other accessories.

Earthing + Lightning protection system

13..10.00 Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI Nos 50.00 0

13.11.00 Supply, tagging, laying or fixing, testing of GI / CU earthing strip / wire in ground at a depth of 600mm including excavation in all type of strata except hard rock or in readymade trenches with necessary clamps, revette jointing as per specification complete as required. Brazed joints for Cu strips, Coating joints with bitumen paint etc. shall be considered. Welding of GI strip to be avoided.

13.11.01 75mm x 6mm thick GI strip. Rmt 50.00 0

13.11.02 50mm x 6mm thick GI strip. Rmt 750.00 0

13.11.03 32mm x 6mm thick GI strip. Rmt 650.00 0

13.11.04 25mm x 6 mm thick GI strip. Rmt 150.00 0

13.11.05 25mm x 3 mm thick GI strip. Rmt 250.00 0

13.11.06 25mm x 3 mm thick CU strip. Rmt 450.00 0

13.11.07 75mm x 6mm thick Cu strip. Rmt 10.00 0

13.11.08 32 mm x 6 mm thick. Cu strip. Rmt 50.00 0

13.11.09 25 mm x 6 mm thick. Cu strip. Rmt 20.00 0

13.11.10 25 mm x 3 mm thick. Cu strip. with green sleeve. Note: Strip required without sleeve if required shall be considered through this quantity only. Rmt 350.00 0

13.11.11 25mm x 3 mm Cu Strip down conductor mounted on porcelain insulator for Lightning Arrestor. Rmt 330.00 0

13.11.12 16 SWG GI wire. Rmt 50.00 0

13.11.13 14 SWG GI wire. Rmt 40.00 0

13.11.14 12 SWG GI wire. Rmt 350.00 0

13.11.15 8 SWG GI wire. Rmt 150.00 0

13.11.16 14 SWG Cu wire. Rmt 25.00 0

13.11.17 12 SWG Cu wire. Rmt 25.00 0

13.11.18 8 SWG Cu wire. Rmt 350.00 0

13.11.19 8 SWG Cu wire with green sleeves Rmt 10.00 0

13.11.20 1C x 50 Sq.mm. 2XFY cable Rmt 29.00 0

13.11.21 1C x 35 Sq.mm. 2XY cable Rmt 180.00 0

13.11.22 1C x 16 Sq.mm. 2XY cable Rmt 10.00 0

13.11.23 1C x 10 Sq.mm. 2XY cable Rmt 10.00 0

13.11.24 4.0 sq.mm. green Cu wire. Rmt 100.00 0

13.12.0 Supply and installation of earth busbar box consisting of 2 x 25 x 3 mm, 300mm long GI Strip with multiple tapping and nut bolt arrangements etc. mounted on SMC insulators. Box shall be fabricated from M.S. sheet including powder coated, clear acrylic hinged door etc. complete. Nos 15.00 0

13.13.0 Supply and installation of earth busbar box consisting of 2 x 50 x 6 mm, 300mm long GI. Strip with multiple tapping and nut bolt arrangements etc. mounted on SMC insulators. Box shall be fabricated from M.S. sheet including powder coated, clear acrylic hinged door etc. complete. Nos 10.00 0

13.13.01 AIR TERMINATION SYSTEM

13.14 Supply of 8mm dia Aluminium alloy Solid Round Conductor of material AlMgSi used in air termination system . Cross sectional area of conductor should be 50 mm². Rmt 1,520.00 0

13.15.0 Supply of Nylon Conductor Holder for Parapet wall for holding 8 mm dia Aluminium alloy round Conductor. Nos 1,435.00 0

13.16.0 Supply of Nylon roof conductor holder for flat roof with concrete block for fixing 8 mm dia Aluminium alloy Solid Round Conductor in the terrace flat surface at every 1 mtr. Nos 270.00 0

13.17.0 Supply of Stainless steel SS / AL 304 Grade Metal roof conductor holder with bottom plate to fix the 8-10 mm dia Aluminium alloy Solid Round Conductor for horizontal air terminal above metal sheet to meet the requirements as per IS/IEC 62305 and IEC 62561-4. Nos 190.00 0

13.18.0 Supply of Adhesion Glue for fixing metal roof conducter holder over the metal surface to meet the requirment of IS/IEC - 62305. Nos 3.00 0

13.19.0 Supply of Stainless steel 304 Grade Cross Connector for 8 mm dia Aluminium alloy round conductor & 10 mm Copper bonded conductor at cross/Tee junction. Nos 141.00 0

13.20.0 Supply of Expansion Joint with connector to compensate the expansion and contraction of Solid Round Al. Conductor during temperature variations. Expansion Joint should be consider at every 20 mtr length of straight horizontal air termination and connected at both the end with use of straight connector conductor. Nos 76.00 0

13.21.0 Supply of Aluminium Straight conductor connector for interconnecting 8mm Aluminium conductor to meets the requirement of IS/IEC 62305. Nos 51.00 0

13.22.0 Supply of air termination rod of 3mtr length of material AlMgSi of diametre ø 16/10 mm crimped on both the ends (Tappered Type). The rod shall be mounted with stainless steel clamp and fixing accessories Nos 11.00 0

13.23.0 Supply of air termination rod of 3 mtr length of material AlMgSi of diametre ø 16/10 mm crimped on both the ends(Tappered Type). The rod shall be mounted with stone and fixing accessories . Test Parameter for 3 mtr vertical air terminal a)ELectrical Resistivity Nos 9.00 0

13.24.0 Supply of stainless steel Earth stud of dimension 69 x 69 mm integrated inside concrete and should be tested for electrical resistivity, salt spray and humidity test & short circuit to meet the requirements of IS/IEC 62305 and IEC 62561-1&2. (for interconnecting Air termination and structral down conductors) Nos 33.00 0

13.25.0 Supply of connecting point made of stainless steel for terminating 10mm copper conductor. Nos 33.00 0

13.26.0 Supply of Aluminuim folding seam conductor holder as per sheet profile for an 8 mm dia aluminium alloy solid round conductor for fixing a horizontal air terminal above the metal sheet to meet the requirements for IS/IEC 62305 and tested as per IEC 62561-4. Nos 15.00 0

STRUCTURAL RISER

13.27.0 Supply of 10 mm copper bonded Solid Steel Round Conductor with average coating thickness minimum of 100µm for Type-B Earthing and should be tested for Tensile strength, Electrical Resistance, salt mist, Bend & Adhesion to meet the requirements of IS/ IEC 62305 and IEC 62561-1&2. Rmt 940.00 0

13.28.0 Supply of Bonding clamp for interconnecting 10 mm Round Conductor with reinforcement rebar at every 3.5Mtr inside the concrete to meet the requirements of IS/IEC 62305. Nos 320.00 0

13.29.0 Supply of stainless steel Straight Connector at every 3Mtr of integrated down conductor and should be tested for electrical resistivity, mechanical load to meet the requirement for IS/IEC - 62305 and IEC 62561-1&2. CAPE Type: SC 8-10 (Article No. 400 210) Nos 190.00 0

13.30.0 Supply of stainless steel Earth stud of dimension 69 x 69 mm integrated inside concrete and should be tested for electrical resistivity, salt spray and humidity test & short circuit to meet the requirements of IS/IEC 62305 and IEC 62561-1&2. Nos 33.00 0

STRUCTURAL FOUNDATION EARTHING

13.31.0 Supply of 10 mm copper bonded Solid Steel Round Conductor with average coating thickness minimum of 70µm for Type-B Earthing and should be tested for Tensile strength, Electrical Resistance, salt mist, Bend & Adhesion to meet the requirements of IS/ IEC 62305 and IEC 62561-1&2. Rmt 925.00 0

13.31.01 Installation of Exothermic Welding - Including welding mould and other accessories for welding confirms the requirements of IEEE 837:2014 : T-Joint, X-Joint, L-Joint , Straight joint Nos 72.00 0

13.32.0 Supply of Corrosion Bitumen tape for inside soil. Nos 8.00 0

L. T. Panels and Distribution Board

13.33 Supply,Unloading, installation, testing & commissioning of MV panel boards compartmental cubicle type freestanding with appropriate cable entries, front operating, front maintained wherever required complete with base frame etc. as required and as per IS 8623/ IEC 61439, Technical specifications & Single line diagram. (Refer Single Line Diagram of Respective Building for Switchgear and other details). Panels shall be as per IEC 61439, fabricated out of 14 / 16 SWG CRCA sheet, and surface treated with phosphating seven tank process and duly powder coated with RAL 7035. Panel vendor shall be CPRI approved manufacturer & shall comply panels as per technical specifications.

13.33.01 Main LT panel ( with Gas flooding system as per specs.) Nos 1.00 0

13.33.02 UPS INPUT PANEL(as per SLD) Nos 1.00 0

13.33.03 UPS OUTPUT PANEL(as per SLD) Nos 1.00 0

13.33.04 EMERGENCY PANEL(as per SLD) Nos 1.00 0

13.33.05 MAIN BUILDING UPS PDB(as per SLD) Nos 1.00 0

13.33.06 SOUTH BLOCK UPS PDB(as per SLD) Nos 1.00 0

13.33.07 NORTH BLOCK UPS PDB(as per SLD) Nos 1.00 0

13.33.08 PUMP ROOM PANEL(as per SLD) Nos 1.00 0

13.33.09 UTILITY PANEL(as per SLD) Nos 1.00 0

13.33.10 TERRACE ROOM PANEL(as per SLD) Nos 1.00 0

13.33.11 LIFT & ESCALATOR PANEL-01(as per SLD) Nos 1.00 0

13.33.12 LIFT & ESCALATOR PANEL -02(as per SLD) Nos 1.00 0

13.33.13 NORTH BLOCK MAIN PANEL(as per SLD) Nos 1.00 0

13.33.14 SOUTH BLOCK MAIN PANEL(as per SLD) Nos 1.00 0

13.33.15 MAIN BLOCK MAIN PANEL(as per SLD) Nos 1.00 0

13.33.16 FF C/O FLOOR PANEL(as per SLD) Nos 1.00 0

13.33.17 450 kVAr RTPFC- Hybrid Panel with 7% detuned and active filter at 415V as per SLD. Nos 2.00 0

13.33.18 LG MAIN FLOOR DB-01(as per SLD) Nos 1.00 0

13.33.19 LG MAIN UPS DB-01(as per SLD) Nos 1.00 0

13.33.20 LG MAIN FLOOR DB-02(as per SLD) Nos 1.00 0

13.33.21 LG MAIN UPS DB-02(as per SLD) Nos 1.00 0

13.33.22 LG MAIN FLOOR DB-03(as per SLD) Nos 1.00 0

13.33.23 LG MAIN UPS DB-03(as per SLD) Nos 1.00 0

13.33.24 MEZ MAIN FLOOR DB(as per SLD) Nos 1.00 0

13.33.25 MEZ UPS DB(as per SLD) Nos 1.00 0

13.33.26 GF MAIN FLOOR DB-01(as per SLD) Nos 1.00 0

13.33.27 GF MAIN UPS DB-01(as per SLD) Nos 1.00 0

13.33.28 KITCHEN MAIN PANEL(as per SLD) Nos 1.00 0

13.33.29 GF KITCHEN UPS DB(as per SLD) Nos 1.00 0

13.33.30 GF MAIN FLOOR DB-02(as per SLD) Nos 1.00 0

13.33.31 GF MAIN UPS DB-02(as per SLD) Nos 1.00 0

13.33.32 GF MAIN FLOOR DB-03(as per SLD) Nos 1.00 0

13.33.33 GF MAIN UPS DB-03(as per SLD) Nos 1.00 0

13.33.34 1F MAIN FLOOR DB-01(as per SLD) Nos 1.00 0

13.33.35 1F MAIN UPS DB-01(as per SLD) Nos 1.00 0

13.33.36 1F MAIN FLOOR DB-02(as per SLD) Nos 1.00 0

13.33.37 1F MAIN UPS DB-02(as per SLD) Nos 1.00 0

13.33.38 1F MAIN FLOOR DB-03(as per SLD) Nos 1.00 0

13.33.39 1F MAIN UPS DB-03(as per SLD) Nos 1.00 0

13.33.40 2F MAIN FLOOR DB-01(as per SLD) Nos 1.00 0

13.33.41 2F MAIN UPS DB-01(as per SLD) Nos 1.00 0

13.33.42 2F MAIN FLOOR DB-02(as per SLD) Nos 1.00 0

13.33.43 2F MAIN UPS DB-02(as per SLD) Nos 1.00 0

13.33.44 3F MAIN FLOOR DB(as per SLD) Nos 1.00 0

13.33.45 3F MAIN UPS DB(as per SLD) Nos 1.00 0

13.33.46 4F MAIN FLOOR DB(as per SLD) Nos 1.00 0

13.33.47 4F MAIN UPS DB(as per SLD) Nos 1.00 0

13.34.0 Supply, installation, testing, tagging, (Circuit numbering) and commissioning of following double door readymade recessed type MCB, DB, fabricated out of CRCA sheet and painted with powder coating process OR made out of scratch proof polycarbonate body and concealed in wall, or on surface or on steel column with necessary mounting frame complete as required along with gland covers at both ends (IP42 min) Si RCCB - Indicates RCCB with enhanced immunity to unwanted tripping under harmonics presence.

13.34.01 04 Way VTPN DB with 63A FP RCBO,100mA as incomer, and 1no.of O/G 10A SP MCB, 2no.of O/G 20A SP MCB, 3no.of O/G 32A TP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.02 06 Way VTPN DB with 63A FP RCBO,100mA as incomer and 3no.of O/G 10A SP MCB, 3no.of O/G 20A SP MCB, 4no.of O/G 32A TP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.03 12 Way SPN DB with 25A DP RCBO,30mA as incomer and 10no.of O/G 10A SP MCB. as outgoing as per SLD. Nos 2.00 0

13.34.04 12 Way SPN DB with 40A DP RCBO,30mA ,Si as incomer and 10no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.05 12 Way SPN DB with 40A DP RCBO,30mA as incomer and 10no.of O/G 10A SP MCB . as outgoing as per SLD. Nos 1.00 0

13.34.06 12 Way SPN DB with 40A DP RCBO,30mA as incomer and 1no.of O/G 10A SP MCB ,9no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 3.00 0

13.34.07 12 Way SPN DB with 40A DP RCBO,30mA as incomer and 8no.of O/G 10A SP MCB ,2no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.08 12 Way SPN DB with 40A DP RCBO,30mA as incomer and 10no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 3.00 0

13.34.09 12 Way SPN DB with 40A DP RCCB,30mA,Si as incomer and 1no.of O/G 10A SP MCB, 9no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.10 12 Way TPN DB with 25A FP RCBO,30mA as incomer and 36no.of O/G 10A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.11 12 Way TPN DB with 25A FP RCBO,30mA as incomer and 36no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.12 12 Way TPN DB with 40A FP RCBO,100mA as incomer and 36no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.13 12 Way TPN DB with 63A FP RCBO,30mA as incomer and 36no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.14 12 Way VTPN DB with 63A FP RCBO,100mA as incomer, and 8no.of O/G 10A SP MCB, 7no.of O/G 20A SP MCB, 7no.of O/G 32A TP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.15 4 Way SPN DB with 25A DP RCBO,30mA as incomer and 2no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 3.00 0

13.34.16 4 Way TPN DB with 25A FP RCBO,30mA as incomer and 12no.of O/G 10A SP MCB. as outgoing as per SLD. Nos 2.00 0

13.34.17 4 Way TPN DB with 40A FP RCBO,30mA as incomer and 12no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.18 4Way TPN DB with 40A FP RCBO,30mA as incomer and 5no.of O/G 10A SP MCB ,7no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.19 6 Way TPN Per Phase Isolation DB with 40A TP MCB as incomer,and 40A DP RCBO as 30mA ,SI 3no.subincomer for Phase segregation and 8no.of O/G 10A SP MCB, 4no.of O/G 20A SP MCB Nos 1.00 0

13.34.20 6 Way TPN DB with 25A FP RCBO,30mA as incomer and 18no.of O/G 10A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.21 6 Way TPN DB with 40A FP RCBO,30mA as incomer and 18no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.22 6 Way TPN DB with 40A FP RCBO,30mA as incomer and 12no.of O/G 10A SP MCB, 6no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.23 8 Way SPN DB with 25A DP RCBO,30mA as incomer and 2no.of O/G 10A SP MCB, 2no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.24 8 Way SPN DB with 25A DP RCBO,30mA as incomer and 6no.of O/G 10A SP MCB. as outgoing as per SLD. Nos 8.00 0

13.34.25 8 Way SPN DB with 25A DP RCCB,30mA,Si as incomer and 3no.of O/G 10A SP MCB,3no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.26 8 Way SPN DB with 40A DP RCBO,30mA as incomer and 6no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 18.00 0

13.34.27 8 Way SPN DB with 40A DP RCBO,30mA as incomer and 1no.of O/G 10A SP MCB, 5no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 8.00 0

13.34.28 8 Way SPN DB with 40A DP RCBO,30mA as incomer and 4no.of O/G 10A SP MCB, 2no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.29 8 Way SPN DB with 40A DP RCBO,30mA,Si as incomer and 1no.of O/G 10A SP MCB, 3no.of O/G 20A SP MCB, 2no.of O/G 25A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.30 8 Way SPN DB with 40A DP RCCB,30mA,Si as incomer and 2no.of O/G 10A SP MCB,4no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.31 8 Way SPN DB with 40A DP RCCB,30mA,Si as incomer and 6no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 2.00 0

13.34.32 8 Way TPN DB with 25A FP RCBO,30mA as incomer and 24no.of O/G 10A SP MCB. as outgoing as per SLD. Nos 4.00 0

13.34.33 8 Way TPN DB with 40A FP RCBO,30mA as incomer and 24no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.34.34 8 Way TPN DB with 40A FP RCBO,30mA as incomer and 18no.of O/G 10A SP MCB, 6no.of O/G 20A SP MCB. as outgoing as per SLD. Nos 1.00 0

13.35.0 Supply, fixing, testing, of good quality industrial sockets with MCB's or MCB isolators of different ratings in readymade IP 42/44 Polycabonate unbreakable enclosure. Box should be suitable to terminate cables / wires easily, complete as required.

13.35.01 16A 1Ø, 3 Pin Socket and plug with 16A SP MCB in a Readymade Box. Nos 20.00 0

13.35.02 32A 3Ø, 5 Pin Socket and plug with 32A FP RCBO in a Readymade Box. Nos 20.00 0

13.35.03 32A 1Ø, 3 Pin Socket and plug with 32A DP RCBO in a Readymade Box. Nos 1.00 0

13.35.04 16A 1Ø, 3 Pin Socket and plug with 16A DP RCBO in a Readymade Box. Nos 1.00 0

13.35.05 16A 3Ø,3 Pin Socket and plug 16A SP MCB + 32A 3Ø, 5 Pin Socket and plug 32A TP MCB in a Readymade Box. Nos 1.00 0

13.35.06 63A 3Ø, 5 Pin Socket and plug with 63A TP MCB in a Readymade Box. Nos 1.00 0

13.35.07 16 A DP MCB in a Readymade enclosure with cable end box for incoming & outgoing cable. Nos 1.00 0

13.35.08 32 A FP MCB in a Readymade enclosure with cable end box for incoming & outgoing cable. Nos 1.00 0

13.35.09 40 A FP MCB in a Readymade enclosure with cable end box for incoming & outgoing cable. Nos 3.00 0

13.35.10 63 A FP MCCB in a Readymade enclosure with cable end box for incoming & outgoing cable. Nos 2.00 0

13.35.11 100 A FP MCCB in a Readymade enclosure with cable end box for incoming & outgoing cable. Nos 5.00 0

13.35.12 125 A FP MCCB in a Readymade enclosure with cable end box for incoming & outgoing cable. Nos 2.00 0

13.35.13 160 A FP MCCB in a Readymade enclosure with cable end box for incoming & outgoing cable. Nos 3.00 0

13.35.14 200 A FP MCCB in a Readymade enclosure with cable end box for incoming & outgoing cable. Nos 1.00 0

13.35.15 250 A FP MCCB in a Readymade enclosure with cable end box for incoming & outgoing cable. Nos 1.00 0

13.35.16 63 A DP MCB in a Readymade enclosure with cable end box for incoming & outgoing cable. Nos 1.00 0

13.35.17 DOL starter suitable for 5 - 7.5 Hp motors. Nos 1.00 0

13.36.0 Supply, installation, testing of set of Bulkhead fixture with 9 W LED or wattage as per lift vendor and 1 No. 5A, 3 pin socket + switch on common good quality board in lift pit. Nos 61.00 0

13.37.0 Supply, fixing, testing, of good quality industrial interlocked switched sockets with MCB's of different ratings in readymade IP 65 Polycabonate unbreakable enclosure. Box should be suitable to terminate cables / wires easily, complete as required.

13.37.01 20A 1Ø, 3Pin Socket and plug with 20A SP MCB in a Readymade Box. Nos 2.00 0

13.37.02 63 A 4 Pole RCCB 100mA + 10A DP MCB in single readymade box for lift machine room. Nos 15.00 0

13.37.03 32A 1Ø, 3 Pin Industrial Socket and plug with 32A DP RCBO in a Readymade Box, on RAW. Nos 2.00 0

13.37.04 16A 1Ø, 3 Pin Industrial Socket and plug with 16A SP MCB in a Readymade Box, on UPS. Nos 1.00 0

13.37.05 16A 1Ø, 3 Pin Industrial Socket and plug with 16A SP MCB in IP65 Readymade Box with Enclosure for EV Car Charging; on RAW Nos 10.00 0

13.37.06 16A 1Ø, 3 Pin Industrial Socket with 16A SP MCB+ 32A 1Ø, 3 Pin Industrial Socket with 32A TP MCB in IP65 Readymade Box with Enclosure for EV Car Charging; on RAW. Nos 10.00 0

13.37.07 40A 3Ø, Industrial Socket with 63A FP RCBO,30mA in a Readymade Box, on RAW. Nos 4.00 0

13.37.08 63A 3Ø, Industrial Socket with 63A FP RCBO,30mA in a Readymade Box, on RAW. Nos 1.00 0

MV CABLE JOINTING & END TERMINATION

13.38.00 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

13.38.01 1 X 35 sq. mm (Unarm.) Nos 8.00 0

MV CABLES & ACCESSORIES

13.39.0 Supply of following LT cables rated for 1100 volts AC as per IS 7098- part 1 of 1998 / IEC 60502 necessary G.I clamps. All the cables shall have FRLSH property also properly clamped or tied when run on cable trays. All such cables shall be provided with temporary labeling at every 20 mtrs and then finally with metal identification tags showing the size and the location from/to the specific Panel/DB at both ends.

Note: Cost Includes following Items : 1) Delivery of the cables at site. 2) Unloading at site store and shifting from store to site where it shall be installed. 3) Laying of cable in the prepared trench / cable tray / duct when laid inside the building or underground when laid outside the building. 4) Excavation in hard or soft murrem / rocky area upto required depth, supply and laying of protection bricks, supply and backfilling with fine sand, leveling the ground to match with the existing condition (As per site condition or as per client requirement).

13.40.0 Supply, testing, tagging, laying and commissioning following sizes of 1100 Volt grade, XLPE / FRLS insulated multistrand Al. / Cu. Conductor armoured / unarmoured Fire Survival Armoured Cables (As Per BS 8434-2 & BS 6387 CWZ) in readymade RCC trench, in provided PVC pipe, RCC pipe hume pipe, on cable trays / ladders etc. as. required complete with clamps for fixing tagging etc.(MLTP TO Main Em. Panel & FF C/O Panel, SYNC. PANEL TO Main EM. Panel)

13.40.01 3.5Cx300 Sq.mm. A2XFY Cable (FS) Rmt 500.00 0

13.41.0 End termination for above Fire Survival Armoured Cables including glands Brass heavy duty, lugs, consumable etc. (End terminations for flexible cables will not be considered separately). (MLTP TO Main Em. Panel & FF C/O Panel, SYNC. PANEL TO Main EM. Panel)

13.41.01 3.5Cx300 Sq.mm. A2XFY Cable (FS) Nos 30.00 0

13.42.0 Supply & installation of readymade hot dip GI. Ladder type tray, shall have 100/ 75/50mm "C" shape channel and rungs at 200 mm CC including readymade accessories e.g. vertical & horizontal bends, Tee's, rightangles, reducers, risers, coupler plates etc. Note: All cable trays shall be powder coated with black color.

13.42.01 1000 x 100 mm ladder tray 14 SWG. Rmt 50.00 0

13.42.02 750 x 75 mm ladder tray 14 SWG. Rmt 80.00 0

13.42.03 600 x 75 mm ladder tray 14 SWG. Rmt 25.00 0

13.42.04 450 x 50 mm ladder tray 14 SWG. Rmt 10.00 0

13.43.00 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

13.43.01 50 mm width X 50 mm depth X 1.6 mm thickness Rmt 10.00 0

13.43.02 100 mm width X 50 mm depth X 1.6 mm thickness Rmt 150.00 0

13.43.03 150 mm width X 50 mm depth X 1.6 mm thickness Rmt 10.00 0

13.43.04 200 mm width X 50 mm depth X 1.6 mm thickness Rmt 350.00 0

13.43.05 300 mm width X 50 mm depth X 1.6 mm thickness Rmt 350.00 0

13.43.06 450 mm width X 50 mm depth X 2.0 mm thickness Rmt 75.00 0

13.43.07 600 mm width X 50 mm depth X 2.0 mm thickness Rmt 300.00 0

13.44.00 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

13.44.01 50 mm width X 50 mm depth X 1.6 mm thickness Nos 5.00 0

13.44.02 100 mm width X 50 mm depth X 1.6 mm thickness Nos 40.00 0

13.44.03 150 mm width X 50 mm depth X 1.6 mm thickness Nos 5.00 0

13.44.04 200 mm width X 50 mm depth X 1.6 mm thickness Nos 50.00 0

13.44.05 300 mm width X 50 mm depth X 1.6 mm thickness Nos 50.00 0

13.44.06 450 mm width X 50 mm depth X 2.0 mm thickness Nos 15.00 0

13.44.07 600 mm width X 50 mm depth X 2.0 mm thickness Nos 40.00 0

13.45.01 Supply and fabrication of M.S. angle / channel supports for wall mounting DB/panels, frames, steel support over trench etc. including necessary painting with 2 coats of primer & 2 coats of enamel paint, & required hardware for fixing of supports etc. complete. Kg 5,000.00 0

13.46.00 Supply and installation of readymade GI Trunking Without Cover of following size with 50 mm depth unless otherwise specified including readymade accessories e.g. Vertical, horizontal bends, tee's, rightangles, reducers, risers, coupler plates etc. Not: Trunking shall be powder coated. It is to be used for DB cluster for cable/wire management and as per architects requirement wherever required.

13.46.01 50 mm GI Trunking Without Cover 16 SWG. Rmt 50.00 0

13.46.02 100 mm GI Trunking Without Cover 16 SWG. Rmt 300.00 0

13.47.00 Engineering, Shop drawing, Supply, installation, testing & commissioning of following size Aluminium Conductor, 3Ph+N, (including external earthing conductors) Sandwitch busducts including necessary accessories like Bends, Elbows, Flanged ends, expansion joint, Tinned Cu flexible connection links at ends of Trafo, MLTP,DG syc panel etc. busbar support(if any), hardware for interconnection, necessary supports, clamps etc. complete. as per specs & actual site requirement.

13.47.01 2500A TPN, AL Sandwitch Busduct (50kA) Rmt 75.00 0

13.47.02 630A TPN, AL Sandwitch Busduct (50kA) Rmt 10.00 0

13.47.03 2500A PH. Crossover box arrangement suitable for above Busduct. (1 Nos / set of busduct) Set 4.00 0

13.47.04 2500A Cu. Flexible end connection set suitable for above Busduct. (2 Nos / set of busduct) Set 8.00 0

13.47.05 630A PH. Crossover box arrangement suitable for above Busduct. (1 Nos / set of busduct) Set 1.00 0

13.47.06 630A Cu. Flexible end connection set suitable for above Busduct. (2 Nos / set of busduct) Set 2.00 0

POINT WIRING, FIXTURES

13.48.00 Supply, installation of point wiring for light, 5A socket points in surface 25 mm dia, 2mm thick FRLS conduits with 2 x 2.5 + 1 x 2.5 Sq.mm LSZH insulated multistrand Cu. conductor wire as sub mains & 2 x 2.5 + 1 x 2.5 Sq.mm. LSZH Insulated multistand Cu. conductor wire for point wiring with 6 Amp SP modular switch fixed on modular switch board in wall, including fancy angle holder / ceiling rose etc. complete as required (submain will not be measured separately). Note:-point wiring is inclusive of back box , modular plate, switches/socket with all required accessories

13.48.01 Light Point wiring for light points with necessary 6A modular switch, ceiling rose compete (.point wiring is inclusive of back box , modular plate, switches/socket) point 106.00 0

13.48.02 Point wiring as above with 2 x 2.5 + 1 x 2.5 Sq.mm. Cu. wire in suitable size FR PVC conduit for Emergency Light Points with controlled from 6A modular switches in Cabins, rooms. (point wiring is inclusive of back box , modular plate, switches/socket) point 32.00 0

13.48.03 As Above but Point wiring for light points with ceiling rose Controlled with MCB (Switching will be from respective lighting DB)(.point wiring is inclusive of back box , modular plate) point 1,800.00 0

13.48.04 As Above but Point wiring for Emergency light points with ceiling rose Controlled with MCB (Switching will be from respective lighting DB).(.point wiring is inclusive of back box , modular plate) point 200.00 0

13.48.05 Point wiring as above using 2 x 4 + 1 x 2.5 Sq.mm. in suitable FRPVC conduit including 1 Nos. modular 6A/16A Switch & Socket with Modular plate, box at one place for utility & printer points fresh / Ex air air fan Points) connections. On raw power (.point wiring is inclusive of back box , modular plate, switches/socket) point 300.00 0

13.48.06 Point wiring as above using 2 x 2.5 + 1 x 2.5 Sq.mm. in suitable FRPVC conduit including 1 Nos. modular 6A/16A Switch & Socket with Modular plate, box at one place for utility & printer points fresh / Ex air air fan Points) connections. On raw power (.point wiring is inclusive of back box , modular plate, switches/socket) point 100.00 0

13.48.07 2 No. 6/16A Socket on UPS Below Table + 1 No.16A Switch Above Table & 1 No. 6/16 Socket with Switch on Raw Above Table suitable to fit in selected workstation table.(co-ordinate with workstation table vendor for exact positioning) (.point wiring is inclusive of back box , modular plate, switches/socket) point 55.00 0

13.48.08 6A 3 pin socket outlets independent (Modular). (.point wiring is inclusive of back box , modular plate, switches/socket) point 30.00 0

13.48.09 6A 3 pin socket outlets on board (Modular). (.point wiring is inclusive of back box , modular plate, switches/socket) point 155.00 0

13.48.10 6/16A 5 pin socket outlets on board (Modular). (.point wiring is inclusive of back box , modular plate, switches/socket) point 1.00 0

13.49.0 Supply & Installation of mains 2 x 2.5 + 1 x 2.5 sq.mm. Cu. multistrand ZHLS Cu. wires 1100 V gr. in dia. 25mm size, 16 SWG GI ERW conduits complete. Rmt 100.00 0

13.50.0 Supply & Installation of mains 2 x 4.0 + 1 x 2.5 sq.mm. Cu. multistrand ZHLS Cu. wires 1100 V gr. in dia. 25mm size, 16 SWG GI ERW conduits complete. Rmt 100.00 0

13.51.0 Supply & Installation of GI ERW conduit with accessories of following sizes with spacer saddles for open or in slab.

13.52.00 Supply,Installation, testing & commissioning of lighting fixtures supplied by vendor with required with suitable control gear, electronic control gear for fluorescent) material including necessary accessories, wiring connection, junction boxes, chain, down drops, supports etc. Scope also includes assembling of trunking fixture or any other type of fixture. Note- Unloading & storage of fixtures are including in scope. The wattage of fixture subject to vary as per lighting vendor design. However, the item for installation will not change. The areas are mentioned in the drawing where the fixtures are to be installed in the individual items. Refer layout for the type of fixture on drawing shared. Relate the drawing with ealier floors and quote accordingly. Any descripancy in consideration please highlight during quoting only.

13.52.01 RECESS MOUNTED 2'x2'LED PANEL, 36W Nos 800.00 0

13.52.02 9W LED DOWNLIGHTER Nos 10.00 0

13.52.03 18W LED DOWNLIGHTER Nos 20.00 0

13.52.04 20W LED BATTEN INDUSTRIAL RAIL Nos 120.00 0

13.52.05 40W LED BATTEN INDUSTRIAL RAIL Nos 275.00 0

13.53.00 Supply, installation, testing & commissioning of indoor recess mounted Different Type of Emergency Exit Signs(all directions) with min. one hour backup with all suitable mounting accessories etc. including wiring connection, two side viewing lamp,supports as required etc. complete. Note :This item & actual qty.shall be procured only after confirmation from Architects/client.

13.54.00 Supply, installation, testing & commissioning of 1200 mm sweep ceiling fan & 600-1000 mm down rod with canopies. Nos 5.00 0

13.55.00 Supply, installation, testing & commissioning of 900 mm sweep ceiling fan & 600-1000 mm down rod with canopies. Nos 1.00 0

13.56.00 Supply, installation, testing & commissioning of 250mm exhaust fan with frame & bird protection louvers including all hardware etc. complete as required. Nos 20.00 0

13.59.0 Supply,Installation, testing & commissioning of 3Phase Input & 3Phase Output UPS with 15/30 minutes Battery back up and sealed maintenance free lead acid maintained in battery racks complete with interconnections, Cu battery cables, Battery breakers. The rack shall be sturdy M.S. section fabricated with powder coating The scope shall include terminals & busbar shrouding for Battery terminals & connections. (Note:- Battery store shall start 150mm above FFL.) NOTE: The UPS configuration is as per SLD.

13.59.01 1 No. x200KVA UPS arrangement as per given specifications and details. Nos 4.00 0

13.59.02 1 No. x30KVA UPS arrangement as per given specifications and details. Nos 2.00 0

13.60.00 Supply, Installation of Sealed maintenance free valve regulated lead acid (VRLA) Battery (with reverse polarity protection MCCB) as per specifications complete suitable for following UPS sizes (Bidder should furnish the battery calculations for 15/30 minutes backup along with the BOQ). Note: The scope also includes complete SITC of cables, DCDBs, DC MCBs, required for battery interconnection as well as interconnections betwwen batteries and UPS with required all accessories.

13.60.01 200 KVA UPS (30 minutes). Set 4.00 0

13.60.02 30 KVA UPS (30 minutes). Set 2.00 0

13.61.00 Installation of battery rack floor mounting as per specifications with necessary fabrication complete for following sizes.

13.61.01 200 KVA UPS (30 minutes). Set 4.00 0

13.61.02 30 KVA UPS (30 minutes). Set 2.00 0

Raceway & Junction Box

13.62.00 Supply and installation of 2 mm thickness Aluminium extruded raceway for under floor installation including necessary cutting of floor providing couplers and clamps for raceway fixing as details provided making good the surface of floor complete as per sizes provided.

13.62.01 100mm x 38 mm deep AL. raceways. Rmt 130.00 0

13.62.02 150mm x 38 mm deep AL. raceways. Rmt 10.00 0

13.63.00 Supply and installation of readymade good quality floor junction boxes of appropriate sizes for raceways with folded frames including counter sunk screw arrangements such that Stainless Steel covers are in level with the floor level. The cover will be Stainless Steel & have 4 Nos. 25 / 32 mm Ø holes with rubber grommets at appropriate location.

13.63.01 150mm X 150mm deep X 50 16SWG junction box with 14 SWG cover. Nos 25.00 0

13.63.02 250mm X 250mm deep X 50 16SWG junction box with 14 SWG cover. Nos 8.00 0

13.63.03 350mm X 350mm deep X 50 16SWG junction box with 14 SWG cover. Nos 1.00 0

13.64.00 Supply & laying of 2mm thick blank FRPVC / GI. conduits of following sizes in floor or in slab including all accessories, deep junction box bends etc.

13.64.01 32mm dia FRPVC conduit Rmt 70.00 0

13.64.02 25mm dia FRPVC conduit. (Conduits in flooring) Rmt 150.00 0

13.64.03 25mm dia GI conduit. (Conduits in flooring) Rmt 20.00 0

EXTERNAL LANDSCAPE

13.65.00 Supply, testing, tagging, laying & commissioning following sizes of 1100 Volt grade, XLPE / PVC insulated multistrand AL/Cu. Conductor armoured / unarmoured cables (As Per IS 1554 & IS 7098) in readymade RCC trench, in PVC pipe, full round RCC hume pipe, on cable trays / ladders etc. as. required complete with clamps for fixing tagging etc.

13.65.01 4Cx4Sqmm 2XWY Cu. Cable complete. Rmt 50.00 0

13.65.02 4Cx2.5Sqmm 2XWY Cu. Cable complete. Rmt 50.00 0

13.65.03 3Cx2.5Sqmm 2XWY Cu. Cable complete. Rmt 50.00 0

13.66.00 End termination for above cables including Double Compression glands Brass heavy duty, Cu lugs, consumable etc. (End terminations for flexible cables will not be considered separately).

13.66.01 4Cx4Sqmm 2XWY Cu. Cable compete. Nos 10.00 0

13.66.02 4Cx2.5Sqmm 2XWY Cu. Cable compete. Nos 10.00 0

13.66.03 3Cx2.5Sqmm 2XWY Cu. Cable compete. Nos 10.00 0

13.67.00 Providing & fixing of Readymade Polycorbonate unbreakable Junction box with 15A, 4way connectors and knowout for 4 cable entry of following size.

13.67.03 150 x 150 x 50mm junction boxes as above but wheatherproof type (IP65) Nos 6.00 0

13.68.00 Supply,Installation, testing, tagging, (Circuit numbering) and commissioning of following double door ready - made recessed type MCB, DB, fabricated out of CRCA sheet and painted with powder coating process OR made out of scratch proof polycarbonate body, and concealed in wall, or on surface with necessary frame complete as required.

13.68.01 External Lighting DB Nos 2.00 0

13.69.00 Supply, Installation, testing and commissioning of 6.0 mtr.(6 mtr above ground) octagonal/conical/rectangular poles (as per supply form clien) with inbuilt cable loop box equivalent to SP-22 but with base plate suitable for mounting on concrete foundation. Scope includes 2 Nos. 40 mm dia PVC Sleeves bent to shape in foundation for cable entry, 16A 4 way connector, 16A SP MCB,earthing of pole with 8 SWG wire, required accessories & hardware, painting with 2 coats of primer & 2 coats of paint of approved shed. Note: Pole Foundation is not in Electrical Contractor scope.

13.69.01 Poles with single bracket Nos 4.00 0

13.69.02 Poles as above but with Double bracket Nos 8.00 0

13.70.00 Installation, testing & commissioning of street / flood light fixture on above poles with necessary controlgear, lamp, hardware etc. including cable connections from junction box.

13.70.01 80W LED weatherproof (IP65/66) Street light luminaire on above 6 mtr. height pole complete. Nos 4.00 0

13.70.02 20W LED weatherproof (IP65/66) Up lighter luminaire. Nos 2.00 0

13.70.03 15/20W Wall bracket/ Up down light LED weatherproof (IP65/66)Up lighter luminaire. Nos 6.00 0

13.70.04 50W Flood light LED weatherproof (IP65/66)Up lighter luminaire. Nos 4.00 0

13.70.05 20W LED weatherproof (IP65/66) Bollard light luminaire on above 1 mtr. height pole complete. Nos 8.00 0

13.70.06 10W LED weatherproof (IP65/66)Up lighter luminaire. Nos 4.00 0

Miscellaneous Items

13.71.00 Supply, installation of material equipment required as per statutorial provision & safety.

13.71.01 1.1 kV class Handgloves pair. Set 2.00 0

13.71.02 Laminated First aid chart with frame. Nos 4.00 0

13.71.03 First aid box. Nos 2.00 0

13.71.04 3 Nos. of Fire buckets with stand having weather shed canopy above the buckets with duly filled coarse sand and "FIRE" wriiten in English & "AAG" written in local (devnagari) language. Set 3.00 0

13.71.05 4.5 Kg. Co2 fire extinguisher mounted on wall. The Co2 Cylinder should be seamless type, ISI marked with monitoring tag & certificate. Vendor to also consider required identification mark (Std color coding, the extinguisher should be visible in No lights) as per Fire / IS Norms. Set 4.00 0

13.71.06 High Voltage Electrical Insulation Synthetic Mats, ISI Marked,confirming to IS:15652-2006. Types: Class C; for 1100V, Flame Retardant, Shock Proof, 1000 mm in width, pastable, Acid/Alkali/Diesel/Oil Resistant, CPRI/ERDA tested & Approved, Black/Gray in color etc. Rmt 30.00 0

13.71.07 415V Dangerboards of appropriate size & marking. Nos 15.00 0

13.73.01 16A 3Ø,3 Pin Socket and plug 16A SP MCB + 32A 3Ø, 5 Pin Socket and plug 32A TP MCB in a Readymade Box. Nos 3.00 0

13.73.02 8 SWG GI wire. Rmt 150.00 0

13.73.04 4Cx4Sqmm 2XWY Cu. Cable complete. Rmt 50.00 0

13.73.05 40W LED BATTEN INDUSTRIAL RAIL Nos 100.00 0

13.73.06 04 Way VTPN DB with 100a FP MCCB as incomer, and 1no.of O/G 10A SP MCB, 2no.of O/G 20A SP MCB, 3no.of O/G 32A TP MCB. Nos 1.00 0

13.74.00 Supply, Transporation, Unloading at site , Installation , Testing and Commissioning of 'Silent Type' Diesel Generating set (Indoor type) with AMF Function having Power rating of1500+250 KVA, 415 Volts at 1500 RPM 0.8 Lagging power factor, consiting of the followings & as per Tender technical specifications. The scope also includes the exhaust piping with Al cladding / insulation including the support structure of exhaust pipe as per CPCB norms & also obtaining approval /Permission from CPCB/Goverment electrical Inspector, Local Muncipal authority etc. DG set also iclude the fuel piping, First charging of Dry Batteries & First fill of Labrication oil. Diesel Engine: Diesel Engine: 4 stroke radiator cooled type with necessary fan, electric start with Electronic Governer, of suitable BHP at 1500RPM suitable for750KVA output of alternator at 45 degree C ,90% RH & 550 Meter MSL and confirming to BS 5514, BS 649, IS 10000, capable of taking 10% over loading for one hour after 12 hours of continious operation. The engine will be fitted complete with all the required accessories.The scope includes testing of engine as per Tender technical specification for electrical works. Alternator : Alternator rated at 1500+250 KVA, 415 Volts 50Hz at 1500 RPM,3 phase 50 Hz, AC supply with 0.8 lagging power factor at 45 degree C,90%RH & at 550 meter MSL. The alternator shall be SPDP enclosure, brushless, continious duty, self excited and self regulated through AVR confirming to IS 4722/BS2613 suitable for tropical conditions and with class F/H Insulation. The scope also includes required control cables between D.G. set to AMF panel to complete the works including required routine test at manufactures works & site test as per specifications. Adopter Box for cable termination with extension bus bars for termination suitable for Armoured cable power cables.

13.74.01 1500 KVA D.G. Set with acoustic canopy{ CPCB 4}, battery, AVM & HSD tank etc. and exhaust piping above building as per latest CPCB norms / requiremnt Set 2.00 0

13.74.02 250 KVA D.G. Set with acoustic canopy{ CPCB 4}, battery, AVM & HSD tank etc. and exhaust piping above building as per latest CPCB norms / requiremnt Set 1.00 0

13.74.03 2x1500+1X250 kVA DG sysn. Panel as per SLD with all DG controler for propoer function of panel in Auto / manual mode in case of mains fail. Set 1.00 0

13.77.02 Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing,mounted on Aluminium/Gl structure of suitable strength with following components complete as required:-a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs e)The liasoning with Statutory body for the solar panel panel shall be in the scope of contractor. The integration of the solar system with the existing electrical network is in the scope of the contractor.

13.77.03 For 125 kWp Solar generation material to used 1) 500 Wp Solar PV Panels with Structure, Earthing, Wiring, and other accessories 2) Power Conditioning Unit(PCU) 125 kWp3]Contractor to consider AC & DC junction box with breakers, AC/DC cables and all other require components and accessories to finish the job Set 1.00 0

TOTAL OF ELECTRICAL WORK 0

14. ELV & ICT WORKS

ADDRESSABLE FIRE ALARM SYSTEM

14.1 S/I/T/C of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications.

14.1.1 10 loop panel Nos 1.00 0

14.1.1a S/I/T/C of networking card Nos 1.00 0

14.1.2 S/I/T/C of Power supply unit to drive the sounder and strobe cum sounder.It shall have inbuilt short circuit protection & Battery Charger.The unit shall deliver 24V DC 10amps and shall be segregated in such fashion that cable to the sounder/strobe cum sounder shall be optimised.Vendor to consider the required cable and termination accessories in scope of suppl.It shall have battery backup features for 30 min ,input power rating must be 220V AC 50Hz/60Hz. Nos 1.00 0

14.1.3 S/I/T/C of intelligent interface unit BACnet/ Modbus protocol i.e.Supplying communication links between building management system and fire alarm control panel complete as required. Nos 1.00 0

14.1.4 S/I/T/C of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required. Nos 1.00 0

14.1.5 S/I/T/C of repeater panel with 320 character/Touch screen LCD display with inbuilt reset,acknowledge and silence switches complete as required. Nos 1.00 0

14.1.7 S/I/T/C of intelligent analog addressable photothermal detector complete with mounting base complete as required.(Below False Ceiling) Nos 78.00 0

14.1.9 S/I/T/C of addressable photoelectric smoke detectors with required accessories Nos 348.00 0

14.1.10 S/I/T/C of addressable photoelectric smoke detectors with required accessories(Below False Ceiling) Nos 534.00 0

14.1.11 S/I/T/C of intelligent addressable thermal detector with rate of rise cum fixed temperature thermistor complete with base as required. Nos 8.00 0

14.1.12 S/I/T/C of addressable beam detector with short circuit isolator (inbuilt or separate) complete with emitter and receiver including connections with remote test features etc. complete as required. Nos 10.00 0

14.1.13 S/I/T/C of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc. as required. Nos 343.00 0

14.1.14 S/I/T/C of addressable manual call point complete as required,with all required accessories. Nos 64.00 0

14.1.15 S/I/T/C of of addressable horn cum strobe complete as required,with all required accessories Nos 94.00 0

14.1.16 S/I/T/C of addressableof fault isolator complete with base as required. Nos 91.00 0

14.1.17 S/I/T/C of addressable control modules for access trip off with required accessories including gi. junction box and glands. Nos 10.00 0

14.1.18 S/I/T/C of addressable control modules for interface with pa system with required accessories including gi. junction box and glands. Nos 16.00 0

14.1.19 S/I/T/C of addressable control modules for AHU trip with required accessories including gi. junction box and glands. Nos 105.00 0

14.1.20 S/I/T/C of addressable control modules for fire damper with required accessories including gi. junction box and glands. Nos 28.00 0

14.1.21 S/I/T/C of addressable control modules for lift interface system with required accessories including gi. junction box and glands. Nos 11.00 0

14.1.22 S/I/T/C of addressable control modules for staircase pressurization with required accessories including gi. junction box and glands. Nos 9.00 0

14.1.23 S/I/T/C of addressable control modules for lift pressurization system with required accessories including gi. junction box and glands. Nos 11.00 0

14.1.24 S/I/T/C of addressable control modules for electrical panel tripping with required accessories including gi. junction box and glands. Nos 2.00 0

14.1.26 S/I/T/C of fire fighter phone jack with control module complete as required. Nos 30.00 0

14.1.27 S/I/T/C of addressable monitor modules for sprinkler flow switches, tamper switch etc. with required accessories including gi. junction box and glands. Nos 20.00 0

14.1.28 S/I/T/C of addressable monitor modules for fire fighting pump. with required accessories including gi. junction box and glands. Nos 12.00 0

14.1.29 S/I/T/C of addressable monitor modules for Beam detector. with required accessories including gi. junction box and glands. Nos 10.00 0

14.1.30 S/I/T/C of 2c x 1.5 sq.mm fire alarm armoured cable,600/1000V rated with annealed copper conductor having XLPE insulatio,steel wire armouring & FRLS outer sheath complete as required Rmt 23,920.00 0

14.2 PUBLIC ADDRESS SYSTEM

14.2.1 S/I/T/C of 6 zone ,voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. Nos 3.00 0

14.2.2 S/I/T/C of 1.5/3/6W ceiling speakers complete as required. Nos 372.00 0

14.2.3 S/I/T/C of 1.5/3/6W box wall speakers complete as required. Nos 79.00 0

14.2.4 S/I/T/C of 2.5/5/10W box wall speakers complete as required. Nos 2.00 0

14.2.5 S/I/T/C of digital audio amplifier 50Watt,25V rms operating at 240 volt AC supply complete as required. Nos 12.00 0

14.2.6 S/I/T/C of digital audio amplifier 75Watt,25V rms operating at 240 volt AC supply complete as required. Nos 15.00 0

14.2.7 S/I/T/C of Voice command keypad 6 zone,with microphone assembly complete as required. Nos 3.00 0

14.2.8 S/I/T/C of Fire Retardant cable PVC insulated copper conductor cable in existing surface/recessed steel conduit of following pairs and cores and size including connection and reconnection as required.

14.2.8.1 Spaeker cable Two pair, 2-core, 1.5 sqmm Rmt 6,776.00 0

14.2.8.2 Supply and Fixing 25 mm dia MS Flexible pipe with PVC coating along with all ancillaries and accessories like couplers etc. as required. Rmt 4,742.00 0

14.3 CCTV SYSTEM

14.3.1 S/I/T/C of Network Low-Light Infra Red (IR) Dome Camera, 1/2.8" CMOS, 5 Mega Pixel (MP) @ 25 Frames Per Second (FPS); Min. Illumination required 0.002 lux @ (color), 120dB True Wide Dynamic Rrange (WDR), Min. Pixels 2592 × 1920p, dual stream, Back light Compensation (BLC), High Light Compensasation (HLC), 3D- Digitial Noise Reduction (DNR), Auto White Balance, Privacy Mask, Region of Interest (ROI); Edge Intelligence: Motion Detection, Video Tampering; H.265, H.264 and MJPEG compression; Audio Input/Output, Alarm Input/Output; Smart IR with upto 40m Infra Red (IR) distance, 256 Giga Byte (GB) Secure Digital (SD) card; Power Over Ethernet (POE) Class 0 and 12 Volt Direct Current (DC), Ingress Protection - IP 65, Impact Resistance - IK 10 with Die-Cast Aluminium Housing, Having Operating temperature range : –40°C to 60° C. Certifications: ONVIF Profile S, G T compliant, Underwriters' Laboratories (UL) 60950-22, European Conformity (CE) (50130-4 & 55022), Federal Communications Commission (FCC) Part 15 and Restriction of Hazardous Substance (RoHS). including cable termination and fixing accessories complete in all respect. Nos 205.00 0

14.3.2 S/I/T/C of Network Low-Light Infra Red (IR) Mini Dome Camera, 1/2.8" CMOS, 2 Mega Pixel (MP) @ 25 Frames Per Second (FPS); Min. Illumination required 0.002 lux @ (color), 120dB True Wide Dynamic Rrange (WDR), Min. Pixels 1920 × 1080p, dual stream, Back light Compensation (BLC), High Light Compensasation (HLC), 3D- Digitial Noise Reduction (DNR), Auto White Balance, Privacy Mask, Region of Interest (ROI); Edge Intelligence: Motion Detection, Video Tampering; H.265, H.264 and MJPEG compression; Audio Input/Output, Alarm Input/Output; Smart IR with upto 20m Infra Red (IR) distance, 256 Giga Byte (GB) Secure Digital (SD) card; Power Over Ethernet (POE) Class 0 and 12 Volt Direct Current (DC), Ingress Protection - IP 65, Impact Resistance - IK 10 with Die-Cast Aluminium Housing, Having Operating temperature range : –40°C to 60° C. Certifications: ONVIF Profile S, G T compliant, Underwriters' Laboratories (UL) 60950-22, European Conformity (CE) (50130-4 & 55022), Federal Communications Commission (FCC) Part 15 and Restriction of Hazardous Substance (RoHS). including cable termination and fixing accessories complete in all respect. Nos 14.00 0

14.3.3 S/I/T/C of Network Low-Light Infra Red (IR) OutDoor Bullet Camera, 1/2.8" CMOS, 5 Mega Pixel (MP) @ 25 Frames Per Second (FPS);2.7–13.5 mm 5X motorized focus & zoom (MFZ) lens Min. Illumination required 0.002 lux @ (color), 120dB True Wide Dynamic Rrange (WDR), Min. Pixels 2592 × 1920p, dual stream, Back light Compensation (BLC), High Light Compensasation (HLC), 3D- Digitial Noise Reduction (DNR), Auto White Balance, Privacy Mask, Region of Interest (ROI); Edge Intelligence: Motion Detection, Video Tampering; H.265, H.264 and MJPEG compression; Audio Input/Output, Alarm Input/Output; Smart IR with upto 40m Infra Red (IR) distance, 256 Giga Byte (GB) Secure Digital (SD) card; Power Over Ethernet (POE) Class 0 and 12 Volt Direct Current (DC), Ingress Protection - IP 67, Impact Resistance - IK 10 with Die-Cast Aluminium Housing, Having Operating temperature range : –40°C to 60° C. Certifications: ONVIF Profile S, G T compliant, Underwriters' Laboratories (UL) 60950-22, European Conformity (CE) (50130-4 & 55022), Federal Communications Commission (FCC) Part 15 and Restriction of Hazardous Substance (RoHS). including cable termination and fixing accessories complete in all respect. Nos 74.00 0

14.3.3 S/I/T/C of Network Low-Light Infra Red (IR) InDoor Bullet Camera, 1/2.8" CMOS, 5 Mega Pixel (MP) @ 25 Frames Per Second (FPS);2.7–13.5 mm Min. Illumination required 0.002 lux @ (color), 120dB True Wide Dynamic Rrange (WDR), Min. Pixels 2592 × 1920p, dual stream, Back light Compensation (BLC), High Light Compensasation (HLC), 3D- Digitial Noise Reduction (DNR), Auto White Balance, Privacy Mask, Region of Interest (ROI); Edge Intelligence: Motion Detection, Video Tampering; H.265, H.264 and MJPEG compression; Audio Input/Output, Alarm Input/Output; Smart IR with upto 40m Infra Red (IR) distance, 256 Giga Byte (GB) Secure Digital (SD) card; Power Over Ethernet (POE) Class 0 and 12 Volt Direct Current (DC), Ingress Protection - IP 66, Impact Resistance - IK 10 with Die-Cast Aluminium Housing, Having Operating temperature range : –40°C to 60° C. Certifications: ONVIF Profile S, G T compliant, Underwriters' Laboratories (UL) 60950-22, European Conformity (CE) (50130-4 & 55022), Federal Communications Commission (FCC) Part 15 and Restriction of Hazardous Substance (RoHS). including cable termination and fixing accessories complete in all respect. Nos 8.00 0

14.3.4 S/I/T/C of 4MP TDN IR 40X Network IR PTZ Camera with minimum specifications as: Sensor Size: 1/1.8" CMOS, Progressive Scan; Effective Pixels: 2592 x 1520; Lens: 5mm~200mm (+/- 10% on each side), 40X optical zoom, DC-IRIS lens with Auto ICR (Infrared Cut Filter); Frames: 25 FPS for all resolution, 50 fps @ 1080p; Min. Illumination: 0.005 lux @ Color & 0 lux IR On; Electronic Shutter: 1/30,000 - 1/1; Smart IR with up-to 450m IR distance; Light Compensation: BLC, HLC, WDR 140dB; Advance Video Compression: H.265 HEVC, H.264 , MJPEG, Smart Codec; Streams: Triple Video Streams configurable at different Resolutions and FPS using H.265/H.264; Noise Reduction (3DNR); PTZ: 400 presets, 4 Patrols, 4 Tours and Auto Pan Scan support; Minimum Edge Intelligence: Smart motion, Scene Change, Intrusion, Multi loitering, People counter, Face detection, Line crossing detection, Unattended object detection, Missing object detection, Audio Detection, Auto-Tracking; Defog and Image Stabilization; 5 Privacy Mask and 5 ROI support; Security: HTTPS, TLS 1.2, Stream encryption, AES-128/256, Secure boot and Secure authentication Hardware Encryption Chipset Built-in; 1TB SD card support with SD card encryption, Signed and Encrypted firmware; Alarm I/O support: 7 In/2 Out; Two-way Audio Support: Line In /Out; Power: AC24V, HPOE, Heater; Environmental Protection: IP67, IK10; Operating temp range : –40°C to 70° C. Certifications: ONVIF Profile S, G, T, M (Listed on ONVIF Website); UL 62368-1, CE (EN 50130-4 & EN 55032), FCC Part 15, RoHS, PCI Data Security Standard, Secured by Default & NDAA Sec 889 compliant. Complete with Brackets suitable for wall / pole mounting as per site conditions and including power supply. Nos 4.00 0

14.3.5 S/I/T/C of 5 mtrs poles for mounting cameras with necessary accessories Nos 28.00 0

14.3.6 S/I/T/C of ANPR Camera Software. Nos 10.00 0

14.3.7 S/I/T/C of Video Management Software Supporting Onvif Profile S & G(Listed On Onvif Website), Psia, Real Time Streaming Protocol (Rtsp) Standards, Should Support 4k Resolution Gpu Rendering On H.264 / H.265 Video Compression Codec. Proposed Vms Should Include 315 Channel Licenses. Video Management Software Shall Include - 1) Perpetual Software Licence, Must Not Be Renewed Periodically 2) Digital Signature And Password Protection On Exported Clips 3) Calender Search With Thumbnail Image Preview Of Recording And Quick Export Of Video Clips 4) Smart Motion Detection On Recorded Video For Multiple Region Of Interest; 5) Tracking Object From Selected Set Of Interlinked Surrounding Cameras With Smart Algorithm (With Min. 12 Cameras) 6) Camera Grid/Layout Sharing Within Operators 7) Create And Save Virtual Cameras In Layout By Digitally Zooming Into The Field Of View Of Camera 8) 3d Positioning To Allow The Operator To Pan, Tilt And Zoom Into A Specific Region Of Interest By Just Clicking The Live View 9) Video Recording On Demand And Adaptive Network Throttling By Auto-Switching Of Camera Streams 10) Custom Video Archival For Every Camera Maximum Upto 5 Years On Fifo Basis 11) View The Video Captured During Pre-Alarm, On-Alarm, Post-Alarm And Live Video From The Camera In A Single 2x2 Layout. 12) Data Encrypted And Secured Transmission On Tls 1.2, Secured By Default Certified 13) Email Event History And Operator Log Reporting With Export To Pdf, Crystal Reports, Ms Excel/Ms Word From Vms Client 14) Gpu Decoding At H.264 / H.265 For 4k Resolution On Cameras 15) Playback With Speeds Ranging From 1/64x To 64x. Smooth Reverse Playback Allows User To View The Reverse Playback Operation Without Any Jerk In The Playback Video Upto 2x Speed. 16) Colored Timeline Depicting Different Recording Happening In The Vms With Min. 3 Colors Software Oem Should Have Toll Free Number For Technical Or Service Support. Lumpsum 1.00 0

14.3.8 S/I/T/C of Recording Server Supporting Onvif Profile S & G, Psia, Real Time Streaming Protocol (Rtsp) Standards, Emerging Technologies In The Industry, Like 4k Resolution, H.264 / H.265 Video Compression Codec. System Proposed Shall Have Scalability Upto 64 Cameras Per Recorder With Sufficient Licenses To Record All The Cameras In This Requirement. It Shall Support Simultaneous Recording, Live Monitoring, Playback/Search Of Recorded Video For All Cameras Supporting, Support Scheduled Backfilling Of The Recordings From The Edge Storage/Sd Card Of Cameras For Robust Recording Against Temporary Network Failure. Recording To Be Considered For 31 Days At Full Resolution, 25 Fps In Raid 5. Vendor To Submit Storage Calculation. It Shall Have Intel® Core™ Xeon™ W-2235, 3.8 Ghz, Minimum 16gb Ram, Single 950w Power Supply, Os Drive: 250gb M.2 Ssd; 5 Field Upgradable Bays Supporting Upto 12 Tb Sata Hard Drives Per Bay, Raid Controller With 4gb Cache Memory Supporting, 0, 1, 5, 6, 10. Nic Card: 2 X 1gbe Supporting Network Throughput Of 570 Mbps, Windows 10, Microsoft Sql Express 2014/2016. 1920x1080 Pixels; Standard Vga/Hdmi Graphics Adapter With Mdp Ports:, Cd/Dvd Rom; Usb Keyboard And Mouse, 3 Usb. Certifications: Ul, Ce/En, Fcc, Rohs. Lumpsum 1.00 0

14.3.9 S/I/T/C of VMS Server Hardware as per following specifications: Intel(R) Xeon(R) Gold 5315Y CPU @ 3.20GHz or higher, 16 processors or higher, Microsoft Windows® Server 2022 64-bit, Microsoft SQL Express/Standard 2019, System Memory (RAM): 32GB, Optical Drive: DVD+/-RW, Hard Disk Drives: Two seperate sets of RAID arrays. RAID set 1 utilizing 10K-15K RPM SSD 480 GB for OS and application, RAID set 2 utilizes 10K-15K RPM SSD 480 GB for DatabaseSQL ; Network Interface Card (NIC): Dual or compatible pair of NICs, 1 Gbps, Human Interface: 102-key keyboard and a mouse pointing device, Video Adapter: 32-bit color or higher, video resolution 1280x768 pixels, 65K colors non-interlaced, Windows Media Player Version 12, Redundant Power supply, UPS, associated cables etc. complete as required. Nos 1.00 0

14.3.10 S/I/T/C of Client Workstation As Per Following Specifications: Intel® Core™ Intel Core I7-10700, Os - Genuine Microsoft Windows® 10 Enterprise 64-Bit, Ram - 16gb, Hard Drives - 500 Gb 7200rpm Sata3, Video Adaptor - Integrated Intel Uhd Graphics 630 Supporting 2 Monitors Over Hdmi/Vga, Network Connection - 1 Gbit/Sec Or Greater, Two(2) Pci-Express Expansion Slots 2/4 Usb, Cd/Dvd Rom, Usb Keyboard And Mouse, Ups, Associated Cables Etc Complete As Required. Nos 4.00 0

14.3.11 S/I/T/C of Color High Resolution Led Tv Comprising Of 42 Inch Display, Full Hd,Hdmi Input Provision; Complete With All Supports And Accessories. Nos 9.00 0

14.3.12 S/I/T/C of Hdd, 8 Tb, 7200 Rpm, Sata 6 Gb/S, Including Fixing Accessories And Cable Termination With Required, Complete In All Respect. (Raid 5 Configuration) Nos 41.00 0

14.4 ACCESS CONTROL SYSTEM

14.4.1 S/I/T/C of 13.56mhz smart card reader with built-in buzzer, color led and tamper output, iso 14443a/b, max read range upto 2-3 inch with weigand data format, suitable for indoor/outdoor applications, ce, fcc, ul294 and rohs compliant, operating temp 0 to 60 deg c as per specification suitable for mounting on metal surface/metal frames or wooden frames wall or as required based on site conditions. Nos 20.00 0

14.4.3 S/I/T/C of 2 reader intelligent controller with built in lan/web server, upgradeable flash memory, 8 supervised inputs and 4 form c relay outputs with 32-bit cpu, 32 mb flash memory, 16 mb sdram memory, real-time clock, dedicated tamper and power fail alarm, support anti pass back (global & local), 8 card formats and 8 facility codes, 128 access levels, 255 holidays and 127 time zones, tcp/ip and rs-485 connectivity, 100,000 card holder and 100,000 offline event buffer, removable terminal blocks wtih color-coded labels, ce, fcc listed. complete with cabinet, power supply, mounting bracket, 3-pin top with 1.5 mts power cable, 4 hrs battery backup and all necessary accessories & peripheral items for civil, electrical works as required. Nos 10.00 0

14.4.4 S/I/T/C of anti-virus software for all pc mentioned below (latest at the time of supply with license ver.) Nos 1.00 0

14.4.5 S/I/T/C of client workstation as per following specifications:intel® core™ intel core i7-8700, 3.2 ghz, os - genuine microsoft windows® 10 enterprise 64-bit, ram - 16gb, hard drives - 1 tb 7200rpm sata3, video adaptor - integrated intel uhd graphics 630 supporting 2 monitors over hdmi/vga, network connection - 1 gbit/sec or greater, two(2) pci-express expansion slots 2/4 usb, cd/dvd rom, usb keyboard and mouse, ups, associated cables etc complete as required Nos 1.00 0

14.4.6 S/I/T/C of color high resolution led tv comprising of 42 inch display, full hd,hdmi input provision; complete with all supports and accessories. Nos 1.00 0

14.4.7 S/I/T/C of enterprise version access control software supporting 5 users and time attendance software. capable of integrating any number of card readers. manage cardholders across multiple sites, ms sql based, multiple door modes: lockout, lockdown, pin only, card+pin, card or pin, card only. the software suite shall comprise various integrated software modules that allow for the full integration and retrieval of transactions from the hardware, as well as alarm monitoring, reporting, and scheduling capabilities. should also support web clients. following features, + zone-related software features, + supervisor card unlock, + card-related software features, + time-limited access, + seemless integartion with cctv system + pin codes, + suspension of cards, + multiple card access + card access groups, + time patterns (schedules), + anti-pass back (apb) control + reporting including tracking and muster report with time stamping + first card rule (activates the door time zone) + two card rule-supervisor card and regular card to allow access + time zone card toggle for door locks, + manual override of system functions + latching mode for door locks , + ldap based and application logon users + inbuild guard tour module, + dynamic floor plans and photo-id badging Nos 1.00 0

14.4.9 S/I/T/C of electromagnetic lock (fail safe type) including necessary mounting brackets. supply shall be complete with l/c/z bracket. double leaf:1200 lbs Nos 3.00 0

14.4.10 S/I/T/C of magnetic contact for doors with all necessary accessories, civil, electrical works & peripheral items, as required. Nos 6.00 0

14.4.12 S/I/T/C of emergency exit switch or break glass unit with feedback (doube pole double throw), key resettable, green colour, fireproof material , suitable for single gang box (including surface mounted back boxes/concealed gi back boxes.) Nos 3.00 0

14.4.13 Supply, Installation, Testing & Commissioning of 1+ 1 Lane configuration (1 Standard + Wide Lane) Swing gates With Stainless steel frame and acrylic flap with 520 mm passage for standard lane & 900mm for wide lane,DC brushless Motor based Highly reliable drive and with tail gate detection feature. Nos 2.00 0

14.4.14 Supply, Installation, Testing & Commissioning of 2+ 1 Lane configuration (2 Standard lane ) Swing gates With Stainless steel frame and acrylic flap with 520 mm passage for standard lane & 900mm for wide lane,DC brushless Motor based Highly reliable drive and with tail gate detection feature. Nos 1.00 0

14.4.15 S/I/T/C of 8c x 0.5 sq.mm frls armoured cable. atc conductor stranded, pvc insulated to form a core, cores laid up, overall shielded with alu-mylar tape with tinned copper drain wire of size 0.5 sq. mm, pvc innersheathed g.i. wire armoured, pvc sheathed cable (colour: gray) Rmt 1,050.00 0

14.4.16 S/I/T/C of 2c x 1.0 sq.mm frls armoured cable. atc conductor stranded, pvc insulated to form a core, cores laid up, overall shielded with alu-mylar tape with tinned copper drain wire of size 0.5 sq. mm, pvc innersheathed g.i. wire armoured, pvc sheathed cable (colour: gray) Rmt 375.00 0

14.4.17 S/I/T/C of 4c x 1.0 sq.mm sq.mm frls armoured cable. atc conductor stranded, pvc insulated to form a core, cores laid up, overall shielded with alu-mylar tape with tinned copper drain wire of size 0.5 sq. mm, pvc innersheathed g.i. wire armoured, pvc sheathed cable (colour: gray) Rmt 100.00 0

14.5 PASSIVE SECURITY SYSTEM

14.5.1 S/I/T/C of multi-zone door frame metal detector not less than 8 real detection zones with all required accessories. Nos 4.00 0

14.5.2 S/I/T/C of handheld metal detector with docking station and built-in charger.with low battery alarm,adjustable detection sensitivity for different requirements,with led for battery/charging indication.with high detection speed with big probe area.with drop-proof protection. Nos 4.00 0

14.5.3 S/I/T/C of x-ray baggage sacnner with all required monitoring station, hardwares & accessories.Tunnel size - 650 mm x 500 mm (for baggage) Nos 2.00 0

a boom barrier 2.5 M Nos 2.00 0

b boom barrier 3 M Nos 2.00 0

c boom barrier 3.5 M Nos 4.00 0

d boom barrier 4 M Nos 2.00 0

14.5.5 S/I/T/C of Frisking Booth with all required fixing and mounting accessories. Nos 2.00 0

14.6 PASSIVE-NETWORK

14.6.5 S/I/T/C of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.(2 runs) Rmt 41,860.00 0

14.6.6 S/I/T/C of keystone shielded outlet, 180dg c6. Nos 745.00 0

14.6.7 S/I/T/C of cat-6 patch cord high speed 10 gigabit 26awg s/ftp patch cord grey, lszh, c6, 1m(user side). Nos 282.00 0

14.6.8 S/I/T/C of cat-6 patch cord high speed 10 gigabit 26awg s/ftp patch cord grey, lszh, c6, 3m(rack end side). Nos 608.00 0

14.6.9 S/I/T/C of backbox for faceplate- box uk style. Nos 234.00 0

14.6.10 S/I/T/C of cat6 face plate shuttered uk style, single. Nos 234.00 0

14.6.12 S/I/T/C of rj45 i/o with required accessories. Nos 1,216.00 0

14.6.13 S/I/T/C of copper panel staggered shielded c6a, 24 port unloaded 1u wire manager included. Nos 33.00 0

14.6.14 S/I/T/C of 12 core indoor armoured cable (mm om-3 / sm) optical fiber cable Rmt 2,000.00 0

14.6.15 S/I/T/C of 24 core fiber sc-style, (mm om-3 / sm), wall mount fiber liu, loaded with adapter plate, pigtail & standard mounting hardware & accessories Nos 30.00 0

14.6.16 S/I/T/C of lc-sc style (mm om-3 / sm) duplex patch cord -5 mtrs. Nos 60.00 0

14.6.17 S/I/T/C of 42u (800w x 1000d)mm floor mount closed rack with front glass door, vertical wire management systems, fan tray on top, perforated rear doors, side doors, casters, opeanable entry at the bottom for the cable & 2 nos vertical power strip with standard accessories. with heavy shelf with sliding keyboard tray, catilever shelf and all necessary hardware to mount the passive & active equipment (pkt of 20). 19" 1u horizotal wire manager (one way) Nos 8.00 0

14.6.18 S/I/T/C of 15u (600w x 600d)mm wall mount closed rack with front glass door, vertical wire management systems, fan tray on top, perforated rear doors, side doors, casters, opeanable entry at the bottom for the cable & 2 nos vertical power strip with standard accessories. with heavy shelf with sliding keyboard tray, catilever shelf and all necessary hardware to mount the passive & active equipment (pkt of 20). 19" 1u horizotal wire manager (one way) Nos 2.00 0

14.6.19 S/I/T/C of 9u (600w x 600d)mm wall mount closed rack with front glass door, vertical wire management systems, fan tray on top, perforated rear doors, side doors, casters, opeanable entry at the bottom for the cable & 2 nos vertical power strip with standard accessories. with heavy shelf with sliding keyboard tray, catilever shelf and all necessary hardware to mount the passive & active equipment (pkt of 20). 19" 1u horizotal wire manager (one way) Nos 4.00 0

14.6.20 S/I/T/C of 6u (600w x 600d)mm wall mount closed rack with front glass door, vertical wire management systems, fan tray on top, perforated rear doors, side doors, casters, opeanable entry at the bottom for the cable & 2 nos vertical power strip with standard accessories. with heavy shelf with sliding keyboard tray, catilever shelf and all necessary hardware to mount the passive & active equipment (pkt of 20). 19" 1u horizotal wire manager (one way) Nos 16.00 0

14.6.21 Providing & erecting Hot-Dip Galvanised Perforated type Cable tray with cover manufactured from 16 swg (1.6 mm thick) GI sheet of 300 mm width & 100 mm height complete with necessary coupler plates, hanging arrangement & hardware in approved manner. Rmt 450.00 0

14.6.22 Providing & erecting Hot-Dip Galvanised Perforated type Cable tray with cover manufactured from 16 swg (1.6 mm thick) GI sheet of 200 mm width & 50 mm height complete with necessary coupler plates, hanging arrangement & hardware in approved manner. Rmt 410.00 0

14.6.24 S/I/T/C of Data Cabling in medium class PVC conduit along with the accessories in surface /recess including the cutting the wall and making good the same in case of recessed conduit as required.25mm Rmt 23,400.00 0

14.7 NETWORK ACTIVE

14.7.1 S/I/T/C of L3 Fully Manageable + Stackable Switch: 12 x 1G SFP+12 x 1G SFP ports and 4 x 10G SFP+ 2x40G uplink ports, with dual hotswap PSU. including standard accessories with 5 years warranty. Nos 2.00 0

14.7.2 S/I/T/C of MM 10G SFP+ Module with Standard Nos 33.00 0

14.7.4 S/I/T/C of L2 Fully Manageable + Stackable Switch: 24 RJ-45 auto-sensing 10/100/1000 ports with 2 combo ports (10/100/1000T or 100/1000X SFP) and 2 SFP+ stacking Uplink Ports including standard connectivity accessories with 5 years warranty. Nos 6.00 0

14.7.6 S/I/T/C of L2 Fully Manageable + Stackable Switch: 24 RJ-45 POE+ auto-sensing 10/100/1000 ports with 2 combo ports (10/100/1000T or 100/1000X SFP) and 2 SFP+ stacking Uplink Ports including standard connectivity accessories with 5 years warranty. Nos 27.00 0

14.7.7 S/I/T/C of MM 1G SFP+ Module with Standard Accessories (vendor to calculate at actual SFP module requried as per the make selected) Nos 33.00 0

14.7.10 S/I/T/C of Wi-Fi 7 (IEEE 802.11be) Indoor Access Point with required mounting accessories. Nos 24.00 0

14.7.11 S/I/T/C of Wireless Controller for centralized Wi-Fi- with 5 year warranty. Nos 1.00 0

14.8 IPABX SYSTEM

14.8.1 S/I/T/C of Pure IP at core server Based voice solution with 04 Port Voicemail ,04 Port FXS ,04 Port FXO ,1 PRI Trunk lines (30 Ch) Circuit with CLIP Facility ,100 IP users License Expandable upto 200 Users,01 Nos. IP Operator Console,100 Party Conference ,Speed Dial, Music on Hold , Internal/ External ring difference ,Call Barring, Call Pickup, TEC should be with GR Number, - Redundant server in active-Active mode.(Vendor to suggest as per the make and model selected.) Nos 1.00 0

14.8.2 S/I/T/C of IP Telephone Set. Nos 86.00 0

14.9.1 S/I/T/C Construction of cable chambers with complete supply of brics masonry, chamber covers & other accessories.

14.9.3 S/I/T/C of 150mm HDPE pipes complete with accessories. Rmt 550.00 0

14.9.4 S/I/T/C of 100mm HDPE pipes complete with accessories. Rmt 315.00 0

14.9.5 S/I/T/C of 50mm HDPE pipes complete with accessories. Rmt 310.00 0

14.9.6 S/I/T/C of 25mm HDPE pipes complete with accessories. Rmt 25.00 0

14.10 INTRUSION SYSTEM

14.10.1 S/I/T/C of 4 zone Control Panel. Nos 4.00 0

14.10.2 S/I/T/C of wireless glass break detector Nos 20.00 0

14.10.3 S/I/T/C of wireless digital PIR motion detector Nos 20.00 0

14.10.4 S/I/T/C of wireless recessed Contacts. Nos 40.00 0

14.10.5 S/I/T/C of wireless indoor siren Nos 12.00 0

14.10.6 S/I/T/C of wireless out-door siren Nos 10.00 0

14.10.7 S/I/T/C of signal cables. (2 core 1 mm2),[1 pair] twisted with overall shield PVC insulated, tinned copper conductor cable,Flexible cable Rmt 600.00 0

14.11 BMS SYSTEM

CENTRAL CONTROL STATIONS

14.11.1 S/I/T/C of the Central Control Stations consisting of the following complete as per tender specification. Nos 2.00 0

14.11.2 S/I/T/C CPU consist of i-7 , suitable Motherboard & Graphic Card, 8 GB RAM [ Expandable up to 32GB ], 500 GB Hard Disk, DVD Writer 52X, Multimedia, modem as per specifications.with Keyboard and mouse Set 2.00 0

14.11.3 S/I/T/C Colour Monitor SVGA - 22 “ Nos 2.00 0

14.11.4 S/I/T/C A4 size Printer Nos 1.00 0

14.11.5 S/I/T/C Windows 10-11 operating system as spported by the BMS OEM Nos 2.00 0

14.11.6 S/I/T/C of the Graphical Software providing the facility to create / provide the following, static and animate the Graphics, Navigation between pages, display of logs, changing the time zones, popup alarms, with Unlimited number of user license configurable password protection for Building Automation System as per Specifications. The BMS platform shall natively support standard communication protocols such as BACnet™/Lonwork etc. The Software should be capable enough to transmit messages on Email Alerts. The software should be Web Based Software Required to remotely monitor the system for unlimited users.Software should support upto 5000 points This Software should have the following Key features 1. WEB BASED TOOL. NO ADDITIONAL SOFTWARE REQUIRED. 2. EMAIL / SMS OPTION AVAILABLE 3. MULTIPLE DATABASE SOURCES / SITE CAN BE INTEGRATED. 4. HTML5 based Software is recomended All should be completed as per tender specification. Set 1.00 0

14.11.7 S/I/T/C Energy Monitoring Software shall be part of proposed BMS software – The software shall display both real time and historical values. Displays in various views including Calendar, graphical and tabular, Line, Pie chart and bar chart. Based on the meter values hourly, daily, weekly and monthly consumption values shall be calculated and displayed. The software shall have facility to define alarms for certain consumption values. There shall be a comparative chart for definable periods for Energy analytics. Defined users shall be able to view the details through Desktop, Mobile or Ipad with auto adjust views based on the type of the device. Set 1.00 0

THIRD PARTY INTEGRATOR

14.11.8 S/I/T/C the necessary Hardwares/Softwares for Integrating it with following 3rd party Devices on Bacnet/Lonworks/Modbus etc., as per distribution given below complete as per tender specification. Set 1.00 0

Load Manager (Refer IO Summary for no of points and devices)

DTM located in Emergency Panel & Lift Panel (Refer IO Summary for no of points and devices)

UPS Integration (Refer IO Summary for no of points and devices)

Fire Alarm System (Refer Fire Alarm BOQ)

DG Set (Refer IO Summary for no of points and devices)

Electrical Soft points refer Electrical IO summary.

DDC CONTROLLERS

S/I/T/C of the following equipment for BMS complete as per tender specification.

14.11.14 Network controller - Providing, installing, testing and commissioning of Microprocessor based 32 Bit Network Supervisory Controller unit for connecting all controllers and 3rd party System Integration Units to it and for transferring data to PC platform. (A) The unit shall comply following codes and standards: UL, FCC and CE. (B) The unit shall support protocol like BACnet (ASHRAE/ANSI 135 standard- and ENV-1805-1/ENV-13321-1)Modbus TCP (C) Shall be able to store reports and event logs. (D) WEB ENABLED / REMOTE DIALING to the unit shall be possible. The controller shall capable of connecting the future expansion DDCs / Integrators. The Controller shall be able to support communication protocol like Lontalk /BACnet /Lonworks etc. controllers. Lumpsum 1.00 0

14.11.15 Programmable and Application specific controller - Providing, installing, testing and commissioning of field mounted DDC controllers (Preferably LAN based ) of the following configurations and as per below specifications: (A) The programmable controllers processors shall be 32-Bit, BTL Certified (B) Analog to Digital and Digital to Analog resolution shall be 12 bit for greater accuracy. (D) Controllers shall support easy GRAPHICAL programming and shall be able to store the programs in the controller itself rather than storing it in PC. (E) The programmable controller shall have Universal input points and each input shall be capable of sensing PULSE signals. The DDC Controllers shall be on BACnet The DDC controller shall be as per the I/O Summary. Equipments, The Controller Selection shall be such that Distance from Controller to Field Devices should be minimum . NOTE : There shall be seperate field mounted controller for each AHU.

14.11.15.1 DDC CONTROLLERS(Vendor to calculate exact number of DDC required as per the make and model selected.) Nos 93.00 0

14.11.15.2 Local make Enclosure for the below units shall have NEMA-1 vandal proof, lockable and secure powder coated MS cabinets and the complete assembly for DDC controllers Nos 93.00 0

SENSORS AND FIELD DEVICES

14.11.18 S/I/T/C of Out Door Air Temp 0-50 Deg C Nos 1.00 0

14.11.19 S/I/T/C of Out Door Air RH 0-100 % Nos 1.00 0

14.11.20 S/I/T/C of Pipe Tempreture 0-50 Deg C Nos 16.00 0

14.11.21 S/I/T/C of Pipe Pressure 0-10 KG/Cm2 Nos 10.00 0

14.11.22 S/I/T/C of Pipe Flow CMH Nos 2.00 0

14.11.23 S/I/T/C of 2-Way Picv/contral valve Nos 1.00 0

14.11.24 S/I/T/C of 3-Way contral valve Nos 12.00 0

14.11.25 S/I/T/C of Level Transmitter Nos 4.00 0

14.11.26 S/I/T/C of Room RH 0-100 Nos 43.00 0

14.11.27 S/I/T/C of Room temp sensor 0-50 Nos 66.00 0

14.11.28 S/I/T/C of Room Return temp 0-50 Nos 15.00 0

14.11.29 S/I/T/C of AHU TT 0-50 Nos 14.00 0

14.11.30 S/I/T/C of DPS 0-25 mm Nos 80.00 0

14.11.35 S/I/T/C of CHW valve Nos 39.00 0

14.11.37 S/I/T/C of Heater TFU Nos 3.00 0

14.11.38 S/I/T/C of Humidifiers Nos 14.00 0

14.11.39 S/I/T/C of DPT 0-60 Pa Nos 10.00 0

14.11.41 S/I/T/C of Water Level Switches: 2 level Nos 14.00 0

14.11.42 S/I/T/C of Oil Level Switch 3 level Nos 1.00 0

CABLES & CONDUITS

S/I/T/C ofof the following Cables complete as per tender specification.

14.11.43 S/I/T/C of signal cables. (2 core 1 mm2),[1 pair] twisted with overall shield PVC insulated, tinned copper conductor cable,Flexible cable Rmt 7,000.00 0

14.11.44 S/I/T/C of signal cables. (4 core 1 mm2),[1 pair] twisted with overall shield PVC insulated, tinned copper conductor cable,Flexible cable Rmt 3,500.00 0

14.11.45 S/I/T/C of communication cables. (4 core 1 mm2),(2 pair) twisted with individual & overall shield PVC insulated, tinned copper conductor cable. Flexible cable Rmt 4,000.00 0

14.11.46 S/I/T/C of LAN cables CAT-6 for BMS Controller connectivity Rmt 4,500.00 0

14.11.47 S/I/T/C of power cables from UPS point to the respective devices and controllers. (3 core 2.5 mm2), PVC insulated, tinned copper conductor cable. Flexible cable Rmt 3,400.00 0

S/I/T/C of the following Conduits complete as per tender specification.

14.11.48 S/I/T/C of GI conduits for underground work of 25mm dia complete with all accessories. [shafts] Rmt 800.00 0

14.11.49 Flexible PVC conduit of 25 mm dia for over ground work. Rmt 1,500.00 0

14.11.50 Rigid PVC conduit of 25 mm dia for over ground work. Rmt 1,500.00 0

S/I/T/C of of Perforated GI cable tray with Cover : complete with supports, all fittings and mounting accessories, etc. complete to installation requirements. All Bends / Tees for cable trays shall be factory fabricated and not site fabricated

14.11.53 S/I/T/C of 24 Port POE with switching capacity of 256 Gbps, forwarding performance 190 Mpps, having 24 x 10/100/1000BASE-T PoE-(RJ45) with minimum PoE budget of 370W and 4x 10G SFP+ uplink ports, should have support for Stacking with stacking bandwidth of minimum 128 Gbps. Should support min 2GB internal DRAM, 2GB internal Flash memory,32K MAC address, 1K IPv6 Multicast Routes, Should have static Routing from day 1 and upgradable to support OSPF and VRRP with 1 year support.Switch should be fully manageable. Nos 4.00 0

TOTAL OF ELV & ICT WORKS 0

15.1 SITC FOR PART I - CHILLERS

15.1.1 VFD Driven, Water Cooled Screw Type Chilled Water Generator with Microprocessor based Panel with BACnet Gateway, to Connect to Plant Manager / Plant Optimizer Operating at 31°C Condenser Cooling Water Inlet, and 7°C Chilled Water Outlet with 12°C Inlet, 210 CMH Chilled Water Flow Rate, 262.5 CMH CW Flow Rate, with Shell & Tube Type Condenser & Evaporator, Fouling Factor - 0.001 for Condensers and 0.0005 for Evaporator in FPS Units,with VFD, suitable for Remote Start / Stop and Auto / Manual Operation with Even No of Passes & Heat Exchange Note : Harmonic Filter Current THD < 4% for each Chiller to be included in Chiller Prices. Minimum efficiency: AHRI Full Load ≤0.5746 ikW/TR | AHRI IPLV ≤0.549 ikW/TR Also Need to furnish efficiency as per IS 16590 - ISEER Ratings Complying to all the technical specifications attached and Chiller rates to include the following: 1) Transportation, loading, unloading, rigging and local erection of chillers at Lower ground floor level of building considering site feasibility and challenges to be included in the rate. 2) Inclusive of charges for 4 point chiller testing at factory for each chiller. 3) Flow switches for each chiller

15.1.1.1 Capacity : 350 TR (2W) + (1S) Nos 3.00 0

15.1.2 Supply, Installation, testing & Commissioning of Common Automatic Tube Cleaning System with all required accessories, (W+S) pumps, control panel and required supports, Suitable for tube cleaning of following chillers: 3 nos. x 350 TR WC Screw chillers Complying to all the technical specifications attached Set 1.00 0

15.2 SITC OF PART II - OTHER HIGH SIDE EQUIPMENT

Note: Transportation, loading, unloading, rigging and local erection of high-side equipment to be included in respective rates. No separate charges will be provided for the same.

15.2.1 Supply, Installation, testing & Commissioning of VFD driven CTI Approved Induced Draft, Twin Cell Counter Flow Type FRP Cooling Tower to Cool 262.5 CMH (350 TR Cooling Capacity Each) of Water from 36°C to 31°C at 27.8°C WBT, at 60.5 M Elevation (2W + 1S) with Fan having Motor of > IE3 and equipped with VFD. Performance efficiency to be ≥ 42 GPM / HP Maximum 0.002% drift loss of re-circulated water volume. Complying to Technical Specifications Attached Note: Each Cooling Tower to be rated for 350 AC TR, however, should be rated for not less than 435 TR Heat Rejection Capacity. Nos 3.00 0

15.2.2 Supply, Installation, testing & Commissioning of 35 mm Antimicrobial / Microban Insulated, Vertical Inline Chilled Water Primary Variable Flow Pumps Motor of > IE3 Efficiency with Head Mounted VFD Complying to Technical Specifications Attached

15.2.2.1 210 CMH Vs 32 M Head (2W+1S) Nos 3.00 0

15.2.3 Supply, Installation, testing & Commissioning of Vertical Inline Condenser Water Pumps with VFD, & Controller for Sequence, Speed etc. with Built in Logic Motor of > IE3 Efficiency with Head Mounted VFD Complying to Technical Specifications Attached

15.2.3.1 262.5 CMH Vs 23 M Head (2W+1S) Nos 3.00 0

15.2.4 Supply, Installation, testing & Commissioning of Vertical Inline Warm water Pumps with Fixed speed motor of > IE3 Efficiency. Pumps to have IP65 rating, include protective canopy suitable for outdoor installation. Complying to Technical Specifications Attached

15.2.4.1 77 CMH Vs 30 M Head (1W+1S) Nos 2.00 0

15.2.5 Supply, Installation, testing & Commissioning of Non-Chemical Condenser Water Treatment Unit Suitable for 3 nos. Cooling Towers (2 W + 1 S) of above-mentioned Capacity with Bac Comber Technology including the following: 1) Inductor Coil in the outlet pipe that generates ULF waves 2) Emitter Unit which is immersed in the cooling tower basin for control of Algae. 3) Electronic Control Unit that is connected to both the inductor coil and emitter unit. This is to be placed close to CT. Set 1.00 0

15.2.6 Supply, Installation, testing & Commissioning of Dirt Separator, for Chilled Water system, 250 NB, Max. Rated for flow of 420 CMH, Complying to the attached technical specifications Nos 1.00 0

15.2.7 Supply, Installation, testing & Commissioning of 35mm Antimicrobial / Microban Insulated with cladding, Closed Diaphragm Type Expansion Vessel 1000 Lts. With Pressurization Unit and Water Make-up connections. Rated for 10 Bar Operation Pressure Complying to the attached technical specifications Nos 1.00 0

15.2.8 Supply, Installation, testing & Commissioning of Automatic Vacuum Degasser suitable for 32 M3 Volume, 10 Bar operating Pressure with feed pumps for make up to Chilled Water Side and Fresh Water Inlet, Connection between piping & degasser, Inlet / outlet connection with built-in Microprocessor based Controller Complying to the attached technical specifications Nos 1.00 0

15.2.9 Supply, Installation, Testing & Commissioning of Filtration Module, Skid Mounted for 1μ, Module suitable for 32 M3 Primary side Volume & 32 M3 Condenser side vol. with (1W+1S) Pumps Starters, Flow Indicator etc. Complying to the attached technical specifications Set 1.00 0

15.2.10 Supply, Installation & testing of Pot Strainer with SS 40 Mesh, & SS Basket 300 NB, Max. Flow of 525 CMH should have canopy / weather protection if deemed required Complying to the attached technical specifications Nos 1.00 0

15.2.11 Supply, Installation, testing & Commissioning of Electrical Power Distribution Panel, including Intelligent Digital Power Meter with transmission, Incoming ACBs / Outgoing MCBs MCCBs, Voltmeter, Ammeter, Lamps & Switches, Contactors etc. with Transformer for Supply to Controllers / Control Valves / Sensors, etc. including power/ Energy meters (kwh) suitable for Local / Remote Operation HVAC Panel to have provison of auto tripping and restart on receipt of fire signal and Feed Backs with suitable Feeders for below mentioned equipment: Complying to the attached technical specifications, having IP55 rating for panels located indoors and IP65 rating for panels located outdoors

15.2.11.1 Panel No. 2A - 3 Nos. of Chillers Refer to attached panel list for reference of list of feeders to be included Nos 1.00 0

15.2.11.2 Panel No. 2B - 3 Nos. of CHW Primary Pumps, 3 Nos. CW Pumps, 1 No.Vaccum Degasser, 1No. Filtration module, etc. Also including feeders for AHU, VRV ODU, etc. Refer to attached panel list for reference of list of feeders to be included Nos 1.00 0

15.2.11.3 Panel No. 24 - 3 No. Cooling Towers with VFDs, Condenser Water Treatment Unit, Warm Water Pumps, Spares, etc. Refer to attached panel list for reference list of feeders to be included Nos 1.00 0

Note: Ensure all feeders/provisions as per HVAC Panel list / SLD has been considered

15.2.12 Supply, Installation, testing & Commissioning of Warm Water Tank of 15M3 Volume for Storage of Condenser Water. Tank to be of IS 2062 construction with epoxy coating. Tank to include inlet and outet connections of 125 NB. Size of tank in rectangular configuration: 4.2M x 1.8M x 2M height Tank to have suitable weather protection for outdoor installation at terrace level. Tank to include the supply and erection of required supports for mounting at terrace level. Complying to the attached technical specifications Nos 1.00 0

15.3 SITC OF PART III : PIPING

15.3A PIPING AND VALVES - CONDENSER SIDE

Note: Centre line Piping measurements will be done. No special additional measurements for all fittings such as Bends, Reducers, Tees, Elbows, etc. The cost for all these items need to be accomodated in running meter rate.

15.3A.1 Supply and Installation of Condenser Water MS Piping as per as per IS 1239 complete with Fittings and Supports Complying to attached technical specifications

15.3A.1.1 300 NB Heavy Rmt 225.00 0

15.3A.1.2 200 NB Heavy Rmt 100.00 0

15.3A.1.3 150 NB Heavy Rmt 25.00 0

15.3A.1.4 100 NB Heavy Rmt 5.00 0

15.3A.1.5 80 NB Heavy Rmt 10.00 0

15.3A.2 Supply and Installation of Valves & Fittings as per Specifications suitable for specified pipe sizes:

15.3A.2.1 Condenser Water Butterfly Valves with body material of Forged Steel / Aluminum Die Cast / ASTM B85-84-383.0, Disc material A351 Gr. CF8M, EPDM 'O' ring spindle seal with PN 16 pressure rating Complying to attached technical specifications

15.3A.2.2 Condenser Water Motorised Butterfly Valves with body material of Forged Steel / Aluminum Die Cast / ASTM B85-84-383.0, Disc material A351 Gr. CF8M, spindle material AISI 410 / 316 , 'O' ring spindle seal with PN 16 pressure rating Note: 230V AC Power supply shall be provided to actuator, Rate should include any provisions required for converting this signal as accepted by actuator Complying to attached technical specifications

15.3A.2.3 Condenser Water Ball Valves with body & bonnet material of Gun Metal / Brass / SS,spindle material SS 304, 'O' ring spindle seal with PN 16 pressure rating Complying to attached technical specifications

15.3A.2.4 Condenser Water Suction Guide cum Strainer with body & cover material of CI 210, flanged connections with SS 80 Mesh, MS or GI guide with PN 16 pressure rating Complying to attached technical specifications

15.3A.2.5 Condenser Water Triple Duty valves with body & cover material of CI 210, valve stem of stainless steel with PN 16 rating Complying to attached technical specifications

15.3A.2.6 Condenser Water Solenoid valves having PN 16 rating. Complying to attached technical specifications

15.3A.2.7 Condenser Water Drain Valves with body material of Forged Steel / Aluminum Die Cast / ASTM B85-84-383.0, Disc material A351 Gr. CF8M, EPDM 'O' ring spindle seal with PN 16 pressure rating Complying to attached technical specifications

15.3A.3 Supply, Installation, testing & Commissioning of Ultasonic Type Flow transmitter suitable for mounting within condenser line of 300 NB rated for up to 10 Bar operating Pressure Complying to attached technical specifications Nos 1.00 0

15.3A.4 Supply and Installation of Three Way Diverting type Valves with Actuator having 4 - 20 mA Input Signal, with Manual Overide Selected for D.P not exceeding 3 Meters. Body material of Cast Iron/ Cast Bronze, Disc material Chrome Nickel Steel, 'O' ring spindle seal with PN 16 pressure rating. Complying to attached technical specifications

15.3A.4.1 Suited for Incoming Flow of 525 CMH and diverting 77 CMH flow to Warm Water Tank & 448 CMH to Cooling Towers against 3-5 m pressure drop Nos 1.00 0

Note: Valve suitable for Incoming Condenser line of 300NB, Warm water line of 125NB and Cooling Tower Line of 300 NB. Required reducers to be considered

15.3B PIPING, INSULATION AND VALVES - PRIMARY SIDE

1) Centre line Piping measurements will be done. No special additional measurements for all fittings such as Bends, Reducers, Tees, Elbows, etc. The cost for all these items need to be accomodated in running meter rate. 2) Insulation thickness for Valves & Fittings shall be the same as the thickness of the pipe on which it is being installed

15.3B.1 Supply and Installation of Antimicrobial / Microban Insulated Primary Side Chilled Water MS Piping as per IS 1239 complete with Fittings and Supports. As per specifications & HVAC Layout

15.3B.1.1 300 NB with 25 mm thick insulation Rmt 75.00 0

15.3B.1.2 200 NB with 25 mm thick insulation Rmt 215.00 0

15.3B.1.3 150 NB with 25 mm thick insulation Rmt 215.00 0

15.3B.1.4 125 NB with 25 mm thick insulation Rmt 165.00 0

15.3B.1.5 100 NB with 25 mm thick insulation Rmt 555.00 0

15.3B.1.6 80 NB with 25 mm thick insulation Rmt 280.00 0

15.3B.1.7 65 NB with 25 mm thick insulation Rmt 270.00 0

15.3B.1.8 50 NB with 25 mm thick insulation Rmt 110.00 0

15.3B.1.9 40 NB with 25 mm thick insulation Rmt 40.00 0

15.3B.1.10 32 NB with 25 mm thick insulation Rmt 150.00 0

15.3B.2 Supply and Installation of Antimicrobial / Microban Insulated Valves & Fittings as per Specifications suitable for below-mentioned pipe sizes:

15.3B.2.1 Chilled Water Insulated Butterfly Valves with body material of Forged Steel / Aluminum Die Cast / ASTM B85-84-383.0, Disc material A351 Gr. CF8M, EPDM 'O' ring spindle seal with PN 16 pressure rating Complying to attached technical specifications

15.3B.2.2 Chilled Water Insulated Motorised Butterfly Valves with body material of Forged Steel / Aluminum Die Cast / ASTM B85-84-383.0, Disc material A351 Gr. CF8M, spindle material AISI 410 / 316 , 'O' ring spindle seal with PN 16 pressure rating Note: 230V AC Power supply shall be provided to actuator, Rate should include any provisions required for converting this signal as accepted by actuator Complying to attached technical specifications

15.3B.2.3 Chilled Water Insulated Non Return Valves with body & cover material of IS 210 Gr. 20, disc material IS 210 Gr. 20 Plastic with PN 16 pressure rating Complying to any related technical specifications provided for this item

15.3B.2.4 Chilled Water Insulated Y' Type Strainer with body material of CI 210 Gr 20 with SS 80 Mesh, PN 16 pressure rating and Complying to attached technical specifications provided for this item

15.3B.2.5 Chilled Water Insulated Ball type Valve with body & bonnet material of Gun Metal / Brass / SS, spindle material SS 304, 'O' ring spindle seal with PN 16 pressure rating Complying to attached technical specifications

15.3B.2.6 Chilled Water Insulated type Suction Guide cum Strainer with body & cover material of CI 210, flanged connections with SS 80 Mesh, MS or GI guide with PN 16 pressure rating Complying to attached technical specifications

15.3B.2.7 Chilled Water Insulated type Triple Duty valves with body & cover material of CI 210, valve stem of stainless steel with PN 16 pressure rating Complying to attached technical specifications

15.3B.3 Supply, Installation, Testing and Commissioning of Drain Valves on Lines 25 NB Ball Type with body & bonnet material of Gun Metal / Brass / SS, spindle material SS 304, 'O' ring spindle seal with PN 16 pressure rating Complying to attached technical specifications related to ball valve. Nos 41.00 0

15.3B.4 Supply, Installation, Testing and Commissioning of Auto Purge Valves to the Highest Point in each chilled water riser (50NB) Nos 4.00 0

15.3B.5 Supply, Installation, Testing and Commissioning of Auto Purge Valves to the Highest Point in AHU chilled water manifold (25NB) Nos 41.00 0

15.3B.6 Supply and Installation of Pressure Independent Two Way Control Valves with Actuator having 4 - 20 mA Input Signal, with Manual Overide, Valve suitable for towards 100% valve authority. Valves to be selected based on below mentioned flow requirement and given pressure drop range of 2 to 3 meters. Valve might be same size or smaller than actual line size of respective AHU. Complying to attached technical specifications

15.3B.7 Supply and Installation of Two Way Control Valves with Actuator having 4 - 20 mA Input Signal, with Manual Overide Selected for D.P not exceeding 3 Meters. Valve authority to be in the range of 0.25 to 0.50. Complying to attached technical specifications

15.3B.7.1 Bypass Line - 150 NB Line Size - Rated for 105 CMH Nos 1.00 0

15.3B.8 Supply, Installation, testing & Commissioning of Ultrasonic Type Flow transmitter for Chilled water Bypass Line Suitable for mounting within 150 NB Dia Chilled Water Piping Line having up to 10 Bar Operating Pressure. Complying to attached technical specifications Nos 1.00 0

15.3B.9 Supply, Installation, testing & Commissioning of Ultrasonic Type Flow transmitter for Chilled water Main Header Line Suitable for mounting within 250 NB Dia Chilled Water Piping Line having up to 10 Bar Operating Pressure. Complying to attached technical specifications Nos 1.00 0

15.3C PIPING, INSULATION AND VALVES - WARM WATER SIDE

1) Centre line Piping measurements will be done. No special additional measurements for all fittings such as Bends, Reducers, Tees, Elbows, etc. The cost for all these items need to be accomodated in running meter rate. 2) Insulation thickness for Valves & Fittings shall be the same as the thickness of the pipe on which it is being installed

15.3C.1 Supply and Installation of Antimicrobial / Microban Insulated Warm Water MS Piping as per as per IS 1239 complete with Fittings and Supports Complying to attached technical specifications. Note : 25 mm Insulation to be provided only on the return line from AHUs

15.3C.1.1 125 NB Heavy 25 mm thick insulation Rmt 110.00 0

15.3C.1.2 125 NB Heavy Rmt 65.00 0

15.3C.1.3 100 NB Heavy 25 mm thick insulation Rmt 155.00 0

15.3C.1.4 100 NB Heavy Rmt 155.00 0

15.3C.1.5 65 NB Heavy 25 mm thick insulation Rmt 245.00 0

15.3C.1.6 65 NB Heavy Rmt 245.00 0

15.3C.1.7 50 NB Heavy 25 mm thick insulation Rmt 100.00 0

15.3C.1.8 50 NB Heavy Rmt 100.00 0

15.3C.1.9 32 NB Heavy 25 mm thick insulation Rmt 10.00 0

15.3C.1.10 32 NB Heavy Rmt 10.00 0

15.3C.2 Supply and Installation of Glass Cloth 160 GSM with Weather Protection Coating Over Warm Water Return Pipe / Valves / Fittings Insulation (Exposed Line)

15.3C.3 Supply and Installation of Antimicrobial / Microban Insulated Valves & Fittings as per Specifications suitable for below-mentioned pipe sizes:

15.3C.3.1 Warm Water Butterfly Valves with body material of Forged Steel / Aluminum Die Cast / ASTM B85-84-383.0, Disc material A351 Gr. CF8M, EPDM 'O' ring spindle seal with PN 16 pressure rating Complying to attached technical specifications

15.3C.3.1.1 125 NB (Non-insulated) Nos 2.00 0

15.3C.3.1.3 65 NB (Non-insulated) Nos 4.00 0

15.3C.3.1.5 50 (NB Non-insulated) Nos 4.00 0

15.3C.3.2 Warm Water Ball Valves with body & bonnet material of Gun Metal / Brass / SS,spindle material SS 304, 'O' ring spindle seal with PN 16 pressure rating Complying to attached technical specifications

15.3C.3.2.3 32 NB (Non-Insulated) Nos 3.00 0

15.3C.3.3 Warm Water Triple Duty valves with body & cover material of CI 210, valve stem of stainless steel with PN 16 rating Complying to attached technical specifications

15.3C.3.3.1 125 NB (Non-Insulated) Nos 2.00 0

15.3C.3.4 Warm Water Drain Valves with body & bonnet material of Gun Metal / Brass / SS,spindle material SS 304, 'O' ring spindle seal with PN 16 pressure rating Complying to attached technical specifications

15.3C.3.4.1 25 NB (Non-Insulated) - Warm Water tank - Drain Nos 1.00 0

15.3C.3.5 Warm Water Y' Type Strainer with body material of CI 210 Gr 20 with SS 80 Mesh, PN 16 pressure rating and Complying to attached technical specifications provided for this item

15.3C.3.5.1 125 NB (Non-Insulated) Nos 2.00 0

15.3C.3.6 Supply and Installation of Three Way Mixing type Valves with Actuator having 4 - 20 mA Input Signal, with Manual Overide Selected for D.P not exceeding 3 Meters. Body material of Cast Iron/ Cast Bronze, Disc material Chrome Nickel Steel, 'O' ring spindle seal with PN 16 pressure rating. Control Valve Authority to be in range of 0.25 to 0.5 Complying to attached technical specifications

15.3C.3.7 Supply, Installation, Testing and Commissioning of Auto Purge Valves to the Highest Point in Warm Water AHU manifold (25NB) Nos 11.00 0

15.3D COMMON ITEMS CONDENSER, CHILLED WATER AND WARM WATER PIPING

15.3D.1 Supply and Installation of 100 mm Dial Type SS Thermometer with Thermowell having SS304/SS316 MOC, Inner and Outer Connection of 1/2" BSP, having stem Length of Min. 150 mm or as per Pipe size and Bore Dia of 13 mm Nos 98.00 0

15.3D.2 Supply and Installation of Pressure Guage, with Barrel Nipple and 6 mm Ball Valve Isolators Nos 108.00 0

15.4 SITC OF PART IV- LOW SIDE AIR-CONDITIONING SYSTEMS WITH CHILLED WATER UNITS | VRV TYPE SYSTEMS

15.4A CHILLED WATER BASED AIR HANDLING UNITS

15.4A.1 Supply, Installation, Testing and Commissioning of Double Skin AHU for Comfort Areas Floor mounted/ Ceiling suspended and of horizontal / vertical / double-decker type and specific size constraints as per tender drawing. with Inlet EU - 4 Filter, CHW Coil of minimum 4-6 Rows as per Coil Conditions specified for Suitable for Coil Conditions Chilled Water Inlet 7°C and Outlet 12°C, UV Lamp for Coil, Plug Fan with VFD or Fan with EC Motor, Having Outlet EU - 8 Filter, Mixing Box (Where Applicable - As per Tender Drawing), RA and FA Dampers, Complying to attached technical specifications for Air Handling Units and having Cooling Capacity and Airflow rate as per below-mentioned requirements:

15.4A.1.1 AHU 1 - 19.5 TR Cooling Capacity, Rated for Air In 24.3°C DB / 17.3°C WB Air Out 11.7°C DB / 11.3°C WB Having Fan rated for 7400 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.2 AHU 3 - 17.7 TR Cooling Capacity, Rated for Air In 24.4°C DB / 17.5°C WB Air Out 11.7°C DB / 11.3°C WB Having Fan rated for 6500 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.3 AHU 4 - 27.6 TR Cooling Capacity, Rated for Air In 23°C DB / 17°C WB Air Out 11.7°C DB / 11.3°C WB, Having Fan rated for 11700 CFM Vs 110 mm SP Nos 1.00 0

15.4A.1.4 AHU 5 - 33.2 TR Cooling Capacity, Rated for Air In 23.7°C DB / 16.8°C WB Air Out 11.7°C DB / 11.1°C WB Having Fan rated for 13200 CFM Vs 120 mm SP Nos 1.00 0

15.4A.1.5 AHU 6 - 5.6 TR Cooling Capacity, Rated for Air In 23.8°C DB / 16.9°C WB Air Out 11.7°C DB / 11.2°C WB, Having Fan rated for 2300 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.6 AHU 9 - 12.5 TR Cooling Capacity, Rated for Air In 25.6°C DB / 17.4°C WB Air Out 11.7°C DB / 11.2°C WB, Having Fan rated for 4600 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.7 AHU 11 - 33.7 TR Cooling Capacity, Rated for Air In 23.1°C DB / 16.3°C WB Air Out 11.7°C DB / 11.2°C WB, Having Fan rated for 14500 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.8 AHU 12 - 19.2 TR Cooling Capacity, Rated for Air In 24.6°C DB / 17.1°C WB Air Out 11.7°C DB / 11.2°C WB, Having Fan rated for 7500 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.9 AHU 14 - 23.6 TR Cooling Capacity, Rated for Air In 24.6°C DB / 17.1°C WB Air Out 11.7°C DB / 11.2°C WB Having Fan rated for 7500 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.10 AHU 15 - 21.5 TR Cooling Capacity, Rated for Air In 32.5°C DB / 21.8°C WB Air Out 11.7°C DB / 11.4°C WB Having Fan rated for 4200 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.11 AHU 19 - 6.5 TR Cooling Capacity, Rated for Air In 24.7°C DB / 17.7°C WB Air Out 11.7°C DB / 11.3°C WB, Having Fan rated for 2300 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.12 AHU 31 - 6.4 TR Cooling Capacity, Rated for Air In 23.8°C DB / 16.9°C WB Air Out 11.7°C DB / 11.2°C WB, Having Fan rated for 2600 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.13 AHU 23 - 21.8 TR Cooling Capacity, Rated for Air In 24.4°C DB / 17.5°C WB Air Out 11.7°C DB / 11.3°C WB, Having Fan rated for 8100 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.14 AHU 26A - 13.3 TR Cooling Capacity, Rated for Air In 26.1°C DB / 17.5°C WB Air Out 11.7°C DB / 11.2°C WB, Having Fan rated for 4700 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.15 AHU 26B - 14.4 TR Cooling Capacity, Rated for Air In 26.5°C DB / 17.5°C WB Air Out 11.7°C DB / 11.2°C WB, Having Fan rated for 5100 CFM Vs 110 mm SP Nos 1.00 0

15.4A.1.16 AHU 26C - 4.3 TR Cooling Capacity, Rated for Air In 25.3°C DB / 17.2°C WB Air Out 11.7°C DB / 11.1°C WB, Having Fan rated for 1600 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.17 AHU 28 - 8.5 TR Cooling Capacity, Rated for Air In 25.8°C DB / 18.7°C WB Air Out 11.7°C DB / 11.4°C WB, Having Fan rated for 2600 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.18 AHU 25A - 4.8 TR Cooling Capacity, Rated for Air In 25.7°C DB / 18.5°C WB Air Out 11.8°C DB / 11.3°C WB, Having Fan rated for 1500 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.19 AHU 25B - 5.8 TR Cooling Capacity, Rated for Air In 24.3°C DB / 17.3°C WB Air Out 11.7°C DB / 11.3°C WB, Having Fan rated for 2200 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.20 AHU 25C - 9.9 TR Cooling Capacity, Rated for Air In 23.9°C DB / 16.9°C WB Air Out 11.7°C DB / 11.3°C WB Having Fan rated for 3500 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.21 AHU 25D - 5 TR Cooling Capacity, Rated for Air In 23.9°C DB / 17°C WB Air Out 11.7°C DB / 11.3°C WB, Having Fan rated for 2000 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.22 AHU 17 - 11.4 TR Cooling Capacity, Rated for Air In 23.9°C DB / 16.9°C WB Air Out 11.7°C DB / 11.2°C WB, Having Fan rated for 4600 CFM Vs 100 mm SP Nos 1.00 0

15.4A.1.23 AHU 29 - 13.2 TR Cooling Capacity, Rated for Air In 23.5°C DB / 16.6°C WB Air Out 11.7°C DB / 11.2°C WB, Having Fan rated for 5600 CFM Vs 100 mm SP Nos 1.00 0

15.4A.2 Supply, Installation, Testing and Commissioning of Double Skin AHU for Critical Areas of the Museum with Temperature and RH Control for Galleries, Related Areas, etc. Floor mounted/ Ceiling suspended and of horizontal / vertical / double-decker type and specific size constraints as per tender drawing. With Inlet EU - 4 Filter, CHW Coil of minimum 4-8Rows as per Coil Conditions specified for Each AHU Suitable for Coil Conditions Chilled Water Inlet 7°C and Outlet 12°C, UV Lamp for Coil, Electric heater as per below mentioned rating, Humidifier as per specified capacity (if applicable and mentioned), Plug Fan with VFD or Fan with EC Motor Outlet EU - 8 Filter, Mixing Box (As Applicable - in Drawing), RA and FA Damper Complying to attached technical specifications for Air Handling Units and having Cooling Capacity and Airflow rate as per below-mentioned requirements:

15.4A.2.1 AHU 20 - 45.1 TR, Cooling Capacity, Rated for Air In 27.3°C DB/ 19.9°C WB Air Out 11.7°C DB / 11.5°C WB, Having Fan Rated for 11600 CFM Vs 115 mm SP, Having Reheaters 6kW X 5 Nos. Nos 1.00 0

15.4A.2.2 AHU 08 - 27.6 TR, Cooling Capacity, Rated for Air In 26.4°C DB / 19.2°C WB Air Out 11.8°C DB / 11.6°C WB, Having Fan Rated for 7500 CFM Vs 115 mm SP, Having Reheaters 6kW X 3 Nos. Nos 1.00 0

15.4A.2.3 AHU 10 - 29.6 TR, Cooling Capacity, Rated for Air In 27°C DB/ 19.7°C WB Air Out 11.7°C DB / 11.4°C WB Having Fan Rated for 7600 CFM Vs 115 mm SP Having Reheaters 5kW X 4 Nos. Nos 1.00 0

15.4A.3 Supply, Installation, Testing and Commissioning of Double Skin AHU for Critical Areas of the Museum with Temperature and RH Control for Galleries, Related Areas, etc. Floor mounted/ Ceiling suspended and of horizontal / vertical / double-decker type and specific size constraints as per tender drawing. With Inlet EU - 4 Filter, CHW Coil of minimum 4-8 Rows as per Coil Conditions specified for Each AHU Suitable for Coil Conditions Chilled Water Inlet 7°C and Outlet 12°C, UV Lamp for Coil, Warm Water Re-heating coil Coils Conditions Warm Water Inlet 25°C and Outlet 20°C as per below mentioned rating, Humidifier as per specified capacity, Plug Fan with VFD or Fan with EC Motor Outlet EU - 8 Filter, (Mixing Box - If applicable as per drawing), RA and FA Damper Complying to attached technical specifications for Air Handling Units and having Cooling Capacity and Airflow rate as per below-mentioned requirements:

15.4A.3.1 AHU 2 - 38.6 TR, Cooling Capacity, Rated for Air In 27.8°C DB/ 20.4°C WB Air Out 11.7°C DB / 11.6°C WB Having Re-Heating Coil Capacity of 27856 kcal/hr. Having Fan Rated for 9100 CFM Vs 100 mm SP Having Humidifier rated for 16 Kg / Hr. Capacity Nos 1.00 0

15.4A.3.2 AHU 27 - 8.2 TR, Cooling Capacity, Rated for Air In 26.1°C DB/ 18.9°C WB Air Out 11.7°C DB / 11.4°C WB, Having Re-Heating Coil Capacity of 6748 kcal/hr, Having Fan Rated for 2400 CFM Vs 100 mm SP Having Humidifier rated for 5 Kg / Hr. Capacity Nos 1.00 0

15.4A.3.3 AHU 7 - 75.3 TR, Cooling Capacity, Rated for Air In 27.8°C DB/ 20.4°C WB Air Out 11.7°C DB / 11.5°C WB, Having Re-Heating Coil Capacity of 55712 kcal/hr., Having Fan Rated for 18200 CFM Vs 120 mm SP, Having Humidifier rated for 31 Kg / Hr. Capacity Nos 1.00 0

15.4A.3.4 AHU 13 - 14.5 TR, Cooling Capacity, Rated for Air In 27.4°C DB/ 20°C WB Air Out 11.7°C DB / 11.5°C WB, Having Re-Heating Coil Capacity of 11326 kcal/hr., Having Fan Rated for 3700 CFM Vs 100 mm SP, Nos 1.00 0

15.4A.3.5 AHU 30 - 12.9 TR, Cooling Capacity, Rated for Air In 26°C DB/ 18.8°C WB Air Out 11.7°C DB / 11.3°C WB, Having Re-Heating Coil Capacity of 11632 kcal/hr., Having Fan Rated for 3800 CFM Vs 100 mm SP Having Humidifier rated for 5 Kg / Hr. Capacity Nos 1.00 0

15.4A.3.6 AHU 18 - 69.4 TR, Cooling Capacity, Rated for Air In 27.1°C DB/ 19.7°C WB Air Out 11.7°C DB / 11.4°C WB, Having Re-Heating Coil Capacity of 55100 kcal/hr., Having Fan Rated for 18000 CFM Vs 115 mm SP Nos 1.00 0

15.4A.3.7 AHU 21A - 45.4 TR, Cooling Capacity, Rated for Air In 27.4°C DB/ 20°C WB Air Out 11.7°C DB / 11.5°C WB Having Re-Heating Coil Capacity of 35203 kcal/hr., Having Fan Rated for 11500 CFM Vs 115 mm SP Nos 1.00 0

15.4A.3.8 AHU 21B - 38.6 TR, Cooling Capacity, Rated for Air In 26.9°C DB/ 19.6°C WB Air Out 11.7°C DB / 11.4°C WB Having Re-Heating Coil Capacity of 31836 kcal/hr., Having Fan Rated for 10400 CFM Vs 115 mm SP Nos 1.00 0

15.4A.3.9 AHU 22 - 55.4 TR, Cooling Capacity, Rated for Air In 27.9°C DB/ 20°C WB Air Out 11.7°C DB / 11.4°C WB, Having Re-Heating Coil Capacity of 42243 kcal/hr., Having Fan Rated for 13800 CFM Vs 115 mm SP Having Humidifier rated for 18 Kg / Hr. Capacity Nos 1.00 0

15.4A.3.10 AHU 16 - 59.9 TR, Cooling Capacity, Rated for Air In 26.1°C DB/ 18.9°C WB Air Out 11.7°C DB / 11.4°C WB, Having Re-Heating Coil Capacity of 51427 kcal/hr., Having Fan Rated for 16800 CFM Vs 115 mm SP Nos 1.00 0

15.4A.3.11 AHU 24 - 61.5 TR, Cooling Capacity, Rated for Air In 25.8°C DB/ 18.6°C WB Air Out 11.6°C DB / 11.3°C WB, Having Re-Heating Coil Capacity of 56779 kcal/hr., Having Fan Rated for 18300 CFM Vs 115 mm SP Having Humidifier rated for 19 Kg / Hr. Capacity Nos 1.00 0

15.4A.4 Supply, Installation, Testing and Commissioning of Humidifiers Suitable for Duct Injection Integrating with Main Supply Duct of respective AHU systems as mentioned and Complying to attached Technical Specifications with following capacity:

15.4A.4.1 AHU 20 - Humidifier rated for 17 Kg / Hr. Capacity Nos 1.00 0

15.4A.4.2 AHU 10 - Humidifier rated for 13 Kg / Hr. Capacity Nos 1.00 0

15.4A.4.3 AHU 13 - Humidifier rated for 6 Kg / Hr. Capacity Nos 1.00 0

15.4A.4.4 AHU 18 - Humidifier rated for 24 Kg / Hr. Capacity Nos 1.00 0

15.4A.4.5 AHU 21A - Humidifier rated for 17 Kg / Hr. Capacity Nos 1.00 0

15.4A.4.6 AHU 21B - Humidifier rated for 13 Kg / Hr. Capacity Nos 1.00 0

15.4A.4.7 AHU 16 - Humidifier rated for 21 Kg / Hr. Capacity Nos 1.00 0

15.4A.5 Supply and Installation of 19 mm Thick Thermal Insulation For Supply & Return Air G.I Duct Complying to attached technical specifications Sqm 10,441.00 0

15.4A.6 Supply and Installation of 25 mm Thick Internal Accoustic Insulation For Initial Supply Air G.I Duct Complying to attached technical specifications Sqm 880.00 0

15.4A.7 Supply and Installation of Extruded Aluminum Powder Coated Plenum Box with 12 mm Fibre Glass Acoustical Insulation and Bottom Operated VCD having, Spigot connection of 200 mm / 250 mm Dia (as per plenum box height). Suitable for connection with Slot Diffusers:

15.4A.7.1 900 mm Length x 150 mm Width x 300 mm Height Nos 38.00 0

15.4A.7.2 900 mm Length x 106 mm Width x 250 mm Height Nos 35.00 0

15.4A.7.3 1000 mm Length x 106 mm Width x 300 mm Height Nos 6.00 0

15.4A.7.4 1000 mm Length x 106 mm Width x 250 mm Height Nos 25.00 0

15.4A.7.5 1000 mm Length x 150 mm Width x 250 mm Height Nos 53.00 0

15.4A.7.6 1000 mm Length x 150 mm Width x 300 mm Height Nos 4.00 0

15.4A.7.7 1200 mm Length x 150 mm Width x 300 mm Height Nos 102.00 0

15.4A.7.8 1200 mm Length x 150 mm Width x 250 mm Height Nos 7.00 0

15.4A.7.9 1200 mm Length x 106 mm Width x 250 mm Height Nos 26.00 0

15.4A.8 Supply and Installation of Extruded Aluminium Manually operated Volume Control Damper having Opposed Blade Type Configuration Complying to attached technical specifications Sqm 50.00 0

15.4A.9 Supply and Installation of Extruded Aluminum Powder Coated Bottom Throw Continuous Slot Diffuser for Supply Air / Return Air having 25mm width for each slot Complying to attached technical specifications

15.4A.9.1 126 mm overall size (2 slot) Rmt 263.00 0

15.4A.9.2 170 mm overall size (3 slot) Rmt 402.00 0

15.4A.10 Supply and Installation of Extruded Aluminum Powder Coated Supply 4 Way Diffuser with Volume Control Damper Complying to attached technical specifications

15.4A.10.1 525 mm x 525 mm listed size Nos 16.00 0

15.4A.10.2 450 mm x 450 mm listed size Nos 55.00 0

15.4A.10.3 375 mm x 375 mm listed size Nos 48.00 0

15.4A.10.4 300 mm x 300 mm listed size Nos 12.00 0

15.4A.10.5 225 mm x 225 mm listed size Nos 4.00 0

15.4A.11 Supply and Installation of Extruded Aluminum Powder Coated Return 4 Way Diffuser Complying to attached technical specifications

15.4A.11.1 525 mm x 525 mm listed size Nos 18.00 0

15.4A.11.2 450 mm x 450 mm listed size Nos 42.00 0

15.4A.11.3 375 mm x 375 mm listed size Nos 48.00 0

15.4A.11.4 300 mm x 300 mm listed size Nos 12.00 0

15.4A.11.5 225 mm x 225 mm listed size Nos 4.00 0

15.4A.12 Supply and Installation of Extruded Aluminum Powder Coated High Ceiling Radial type Swirl Diffuser for Supply air along with Plenum Box, VCD and having 12 to 16 blades and rated for 5M+ vertical throw and 360° flow. Complying to attached technical specifications

15.4A.12.1 Φ 400 mm Dia listed size Nos 205.00 0

15.4A.13 Supply and Installation of Extruded Aluminum Powder Coated Eye Ball type Jet Nozzles having provision for volume control Complying to attached technical specifications

15.4A.13.1 400 mm Dia listed size Nos 40.00 0

15.4A.13.2 325 mm Dia listed size Nos 15.00 0

15.4A.14 Supply and Installation of Extruded Aluminum Powder Coated Rectangular Acoustical Louvers for Return air through critical areas such as galleries, etc., having following sizes and complying to attached technical specifications

15.4A.14.1 5000 mm X 500 mm listed size Nos 1.00 0

15.4A.14.2 2000 mm X 500 mm listed size Nos 1.00 0

15.4A.14.3 1200 mm X 300 mm listed size Nos 1.00 0

15.4A.14.4 2200 mm X 400 mm listed size Nos 2.00 0

15.4A.14.5 2500 mm X 400 mm listed size Nos 1.00 0

15.4A.14.6 3200 mm X 500 mm listed size Nos 2.00 0

15.4A.14.7 3700 mm X 400 mm listed size Nos 1.00 0

15.4A.14.8 5000 mm X 700 mm listed size Nos 1.00 0

15.4A.14.9 1500 mm X 400 mm listed size Nos 1.00 0

15.4A.14.10 3800 mm X 800 mm listed size Nos 1.00 0

15.4A.14.11 4500 mm X 600 mm listed size Nos 2.00 0

15.4A.14.12 5000 mm X 600 mm listed size Nos 1.00 0

15.4A.14.13 5000 mm X 800 mm listed size Nos 3.00 0

15.4A.14.14 4300 mm X 500 mm listed size Nos 2.00 0

15.4A.15 Supply, Installation, Testing and Commisioning of Power Distribution Panel for AHUs System & Related HVAC equipment with incoming Isolator, and Outgoing MCCBs / MCBs, with Intelligent Power Meter for display of Voltages, Current And Power, with Totalizer, Potential free contacts for BMS connectivity of equipment and Voltage sensor suitable for Local / Remote Operation as per all mentioned technical specifications and incoming / outgoing feeders for following panel-wise HVAC equipment: AHU fans, (VFDs as applicable), Door Switch, UV Lamp, Motorized Valves, Dampers, Humdifiers, Electrical Heaters, etc. as applicable per system. Complying to attached technical specifications for electrical panel Refer to HVAC Panel list and SLD for reference of feeders and provisions to be considered per respective panel no. as mentioned below:

15.4A.15.1 HVAC Panel 03 Nos 1.00 0

15.4A.15.2 HVAC Panel 05 Nos 1.00 0

15.4A.15.3 HVAC Panel 06 Nos 1.00 0

15.4A.15.4 HVAC Panel 07 Nos 1.00 0

15.4A.15.5 HVAC Panel 08 Nos 1.00 0

15.4A.15.6 HVAC Panel 09 Nos 1.00 0

15.4A.15.7 HVAC Panel 10 Nos 1.00 0

15.4A.15.8 HVAC Panel 11 Nos 1.00 0

15.4A.15.9 HVAC Panel 12 Nos 1.00 0

15.4A.15.10 HVAC Panel 13 Nos 1.00 0

15.4A.15.11 HVAC Panel 14 Nos 1.00 0

15.4A.15.12 HVAC Panel 15 Nos 1.00 0

15.4A.15.13 HVAC Panel 16 Nos 1.00 0

15.4A.15.14 HVAC Panel 17 Nos 1.00 0

15.4A.15.15 HVAC Panel 18 Nos 1.00 0

15.4A.15.16 HVAC Panel 19 Nos 1.00 0

15.4A.15.17 HVAC Panel 20 Nos 1.00 0

15.4A.15.18 HVAC Panel 21 Nos 1.00 0

15.4A.15.19 HVAC Panel 22 Nos 1.00 0

15.4A.15.20 HVAC Panel 26 Nos 1.00 0

15.4A.15.21 HVAC Panel 27 Nos 1.00 0

15.4A.15.22 HVAC Panel 28 Nos 1.00 0

15.4A.16 Supply, Installation & testing of UL555 rated Motorized Fire & Smoke Damper suitable for duct mounting. Note: 230V AC Power supply shall be provided to actuator, Rate should include any provisions required for converting this signal as accepted by actuator. Dampers to be normally open and should close based on 1) fire signal input 2) Temperature beyond set limit of 74C. Complying to technical specifications attached. Damper with sleeve and having following sizes:

15.4B VRV / VRF SYSTEM BASED AC SYSTEM

15.4B.1 VRV EQUIPMENT

Note : All VRV Systems need to have BMS compatibility for Remote monitoring and control. All software, hardware and provisions required for BMS integration need to be included.

15.4B.1.1 Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), microprocessor based Controller, top discharge type condensing unit(s), with R410 A Refrigerant (Or Eco Friendly Green Gas if any), vibration isolators, with suitable foundation, MS Stand for Unit with necessary paint etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. Having COP rating of 3.8 or higher. Complying to attached technical specifications Including System commissioning of VRV system and additional charges of Gas and Compressor oil as required

15.4B.1.1.1 101 KW | 36 HP Cooling Capacity Nos 1.00 0

Note: VRV ODU system to be able to integrate with Below mentioned 4 nos. AHU system DX Coils and Expansion Kits. Any upgradations / changes to the ODU capacity required for the same to be done at no extra cost

15.4B.1.2 Supply, Installation, Testing and Commissioning of Double Skin Ceiling Suspended AHU with specific size constraints as per tender drawing. for Areas of the Museum which require 24 x 7 cooling . Inlet EU - 4 Filter, Dual coil in series: CHW + DX along with expansion kit, CHW Coil to be of minimum 4-8 Rows as per Coil Conditions specified for Each AHU, Chilled Water Inlet 7°C and Outlet 12°C, Minimum 2 nos. Plug fans with Fan providing at least 75 to 100% redundancy even if 1 fan is not working, RA damper if applicable: Complying to attached technical specifications for Air Handling Units

15.4B.1.2.1 AHU for IT Work room - 4.8 TR, Cooling Capacity DX Coil + CHW Coil Fan Rated for 1650 CFM Vs 25 mm SP Nos 1.00 0

15.4B.1.2.2 AHU for Server room - 5.5 TR, Cooling Capacity DX + CHW Coil Fan Rated for 3150 CFM Vs 25 mm SP Nos 1.00 0

15.4B.1.2.3 AHU for UPS Bank room - 9 TR, Cooling Capacity DX + CHW Coil Fan Rated for 5400 CFM Vs 15 mm SP Nos 1.00 0

15.4B.1.2.4 AHU for BMS room - 3.8 TR, Cooling Capacity DX + CHW Coil Fan Rated for 2300 CFM Vs 15 mm SP Nos 1.00 0

15.4B.1.3 Supply & Installation of (Piping Joints) Gas & Liquid Line Pair of Refnets for above mentioned VRV Indoor / Outdoor units as per VRV OEM standard specifications Set 4.00 0

15.4B.1.4 Supply & Installation of Electronic Expansion Kit Suitable for integration of VRV Outdoor Unit with Respective AHU system. Expansion Kit Having follow capacity / configuration:

15.4B.1.4.1 EEV Suitable for 4.8 TR Cooling Load Set 1.00 0

15.4B.1.4.2 EEV Suitable for 5.5 TR Cooling Load Set 1.00 0

15.4B.1.4.3 EEV Suitable for 9 TR Cooling Load Set 1.00 0

15.4B.1.4.4 EEV Suitable for 3.8 TR Cooling Load Set 1.00 0

15.4B.1.5 Supply & Installation of Corded Remote Controller per AHU System Connected to the VRV Outdoor Unit Nos 4.00 0

15.4B.1.6 Supply & Installation of Centralized Remote Controller for VRV Outdoor Unit suitable for integrating all AHU systems (IDUs) and having BMS Connectivity Nos 1.00 0

15.4B.1.7 Supply, Installation & testing of Copper Piping & Fitting for Suction Line with 19 mm thermal Insulation complying to technical specifications for copper piping and copper piping insulation. As per following Pipe sizes:

15.4B.1.8 Supply, Installation & testing of Copper Piping & Fitting for Discharge Line with 13 mm thermal Insulation complying to technical specifications for copper piping and indoor refrigerant piping insulation. As per following Pipe sizes:

15.4B.1.9 Supply & Installation of PVC Drain Piping with 6 mm Nitrile / EPDM Class "O" Insulation, Complying to attached technical specifications. As per following pipe sizes:

15.5 SITC OF PART V : TOILET VENTILATION SYSTEMS

15.5A TOILET VENTILATION

15.5A.1 Supply, Installation, testing & Commissioning of Ceiling Suspended Cabinet type Exhaust Air fans including accessories such as wire mesh, supports, canvas connection, etc. 1. Vendor needs to rework fan static calculation as per actual shop drawing, motors to be IE3 rated or better 2. Kindly consider panel list for bifurcation of single phase and three phase fans Complying to attached technical specifications Fans having the following capacity:

15.5A.1.1 1600 CFM Vs 25 mmwg SP Nos 2.00 0

15.5A.1.2 1700 CFM Vs 25 mmwg SP Nos 1.00 0

15.5A.1.3 2150 CFM Vs 20 mmwg SP Nos 1.00 0

15.5A.2 Supply, Installation, testing & Commissioning of Ceiling Suspended Inline type Exhaust Air fans including accessories such as wire mesh, supports, canvas connection, etc. 1. Vendor needs to rework fan static calculation as per actual shop drawing, motors to be IE3 rated or better 2. Kindly consider panel list for bifurcation of single phase and three phase fans Complying to attached technical specifications Fans having the following capacity:

15.5A.2.1 1100 CFM Vs 20 mmwg SP Nos 1.00 0

15.5A.2.2 900 CFM Vs 20 mmwg SP Nos 1.00 0

15.5A.2.3 600 CFM Vs 20 mmwg SP Nos 3.00 0

15.5A.2.4 200 CFM Vs 20 mmwg SP Nos 1.00 0

15.5A.2.5 600 CFM Vs 20 mmwg SP Nos 1.00 0

15.5A.2.6 400 CFM Vs 20 mmwg SP Nos 2.00 0

15.5A.2.7 1000 CFM Vs 20 mmwg SP Nos 1.00 0

15.5A.2.8 700 CFM Vs 20 mmwg SP Nos 1.00 0

15.5A.2.9 1400 CFM Vs 25 mmwg SP Nos 1.00 0

15.5A.2.10 1300 CFM Vs 20 mmwg SP Nos 1.00 0

15.5A.2.11 1300 CFM Vs 15 mmwg SP Nos 1.00 0

15.5A.3 Supply, Installation, testing & Commissioning of Wall Mounted Type Propeller Exhaust Air fan Fan Complete with any required accessories including weather protective louver compying to attached Technical Specifications for Weather Louver. Fan Dia to be suitable for Exhaust flow up to 100 CFM and for mounting within wall opening of 150mm x 150mm Nos 4.00 0

15.5A.4 Supply & Installation of Circular Exhaust Air Disc Valve in Plastic Construction suitable for Toilet Exhaust with provision for air volume control and complying to attached technical specifications. Having following Sizes:

15.5A.5 Supply & Installation of Extruded Aluminium Powder Coated Non Vision Type Door Louver for Fresh Air / Replacement Air Intake into Toilets / Washrooms Complying to attached technical specifications

15.6 SITC OF PART VI : PRESSURIZATION SYSTEM

Note: Charges for Testing & Commissioning of Staircase and Liftwell Pressurization systems along with required documents to be included within the rates of respective systems. No separate charges will be paid for the same

15.6A STAIRWELL PRESSURIZATION SYSTEM

15.6A.1 Supply, Installation, Testing and Commisioning of Tube Axial Type Fan, Direct Drive Motor with VFD including all required accessories and mounting arrangement as per drawing. Complying to attached technical specifications. Fans to be rated for the following Capacity:

15.6A.1.1 5500 CFM Vs 25 mm swg for ST-01 (Closed + Open Door) Nos 1.00 0

15.6A.1.2 16000 CFM Vs 25 mm swg for ST-01 (Open Door) Nos 1.00 0

15.6A.1.3 5000 CFM Vs 25 mm swg for ST-02 (Closed + Open Door) Nos 1.00 0

15.6A.1.4 18000 CFM Vs 25 mm swg for ST-02 (Open Door) Nos 1.00 0

15.6A.1.5 6000 CFM Vs 25 mm swg for ST-03 (Closed + Open Door) Nos 1.00 0

15.6A.1.6 18000 CFM Vs 25 mm swg for ST-03 (Open Door) Nos 1.00 0

15.6A.1.7 25500 CFM Vs 30 mm swg for ST-E1& ST-E2 (Closed + Open Door) Nos 2.00 0

15.6A.2 Supply, Installation, Testing and Commissioning of Differential Pressure Transmitters for staircase pressurization application, having 0 - 100 Pa or 0 - 10 mm Pressure Range and having output available in 4-20 mA range, Complying to attached technical specifications 2 Nos. DPTs considered per each Staircase. To be placed at the lowest and highest occupied level of each respective stair-well Nos 10.00 0

15.6B LIFT WELL PRESSURIZATION SYSTEM

15.6B.1 Supply, Installation, Testing and Commisioning of Tube Axial Type Fan, Direct Drive Motor including all required accessories and mounting arrangement as per drawing. Complying to attached technical specifications. Fans to be rated for the following Capacity:

15.6B.1.1 5000 CFM Vs 30 mm SWG ( Lift-S1 & S2 ) Nos 1.00 0

15.6B.1.2 3000 CFM Vs 25 mm SWG ( Lift-N2 & N3 ) Nos 2.00 0

15.6B.1.3 4000 CFM Vs 35 mm SWG ( Lift-E3 ) Nos 1.00 0

15.6C COMMON ITEMS FOR STAIRWELL & LIFT WELL PRESSURIZATION

15.6C.1 Supply, Installation, Testing and Commissioning of Power Distribution Panel having Emergency Incoming Power Provision, with Switches Suitable for Outdoor Installation Connectors, Transmitters, By pass Starters, Isolators, with Remote Start/Stop , VFD and Auto / Manual Facility Complying to attaching technical specificatons. Refer HVAC Panel list for list of feeders

15.6C.1.1 HVAC Panel 23 for 5500 CFM & 16000 CFM Pressurization Fans Nos 1.00 0

15.6C.1.2 HVAC Panel 25 for 5000 CFM, 18000 CFM, 6000 CFM, 3000 CFM Pressurization Fans Nos 1.00 0

15.6C.1.3 HVAC Panel 30 for 25500 CFM Pressurization Fans Nos 1.00 0

15.6C.1.4 HVAC Panel 31 for 25500, 4000 CFM Pressurization Fans Nos 1.00 0

15.6C.1.5 HVAC Panel 32 for 5000 CFM Pressurization Fans Nos 1.00 0

15.7 SITC OF PART VII : UTILITY AREA VENTILATION SYSTEMS

15.7A PANEL ROOM & PUMP ROOM VENTILATION

15.7A.1 Supply, Installation, testing & Commissioning of Ceiling suspended Axial type Exhaust Air Fan,with all required mounting (i.e. canvas, wiremesh, supports, etc.) Direct Drive with Motor suitable for 250 ° C X 2 Hrs Rating. Vendor needs to rework fan static calculation as per shop drawing. Motors to be IE3 rated or better. Also check HVAC drawing for any Dia constraints for fan selection in alloted space. Complying to Technical Specifications Attached

15.7A.1.1 26400 CFM Vs 40 mmwg SP Nos 1.00 0

15.7B DG ROOM & PUMP ROOM VENTILATION

15.7B.1 Supply, Installation, testing & Commissioning of Ceiling suspended Axial type Fresh Air Fan,with all required mounting (i.e. wiremesh, supports, etc.) Direct Drive with Motor. Vendor needs to re-work fan static calculation as per shop drawing motors to be IE3 rated or better. Fan outlet speed should not be more than 13 -15m/s. Also check HVAC drawing for any Dia constraints for fan selection in alloted space. Complying to attached technical specifications

15.7B.1.1 46000 CFM Vs 35 mmwg SP Nos 4.00 0

15.7B.2 Supply, Installation, testing & Commissioning of Ductless Induction Ceiling Suspended Ventilation, Dual Speed Jet Fan Assembly suitable for 250 °C X 2 Hrs Rating

15.7B.2.1 400 Φ, 3300CFM (Normal Mode)/ 6600 CFM ( Fire Mode) Nos 2.00 0

15.7C STP PUMP ROOM VENTILATION

15.7C.1 Supply, Installation, testing & Commissioning of Ceiling suspended Axial type Fresh Air Fan,with all required mounting (i.e.wiremesh, supports, etc.) Direct Drive with Motor. Vendor needs to rework fan static calculation as per shop drawing motors to be IE3 rated or better. Fan outlet speed should not be more than 13 -15m/s. Also check HVAC drawing for any Dia constraints for fan selection in alloted space. Complying to attached technical specifications

15.7C.1.1 4100 CFM Vs 25 mmwg SP Nos 1.00 0

15.7C.2 Supply, Installation, testing & Commissioning of Ceiling suspended Axial type Exhaust Air Fan,with all required mounting (i.e.wiremesh, supports, etc.) Direct Drive with Motor suitable for 250° C X 2 Hrs Rating. Vendor needs to rework fan static calculation as per shop drawing motors to be IE3 rated or better. Also check HVAC drawing for any Dia constraints for fan selection in alloted space. Complying to attached technical specifications

15.7C.2.1 4100 CFM Vs 30 mmwg SP Nos 1.00 0

15.7D METERING KIOSK ROOM VENTILATION

15.7D.1 Supply, Installation, testing & Commissioning of Ceiling Suspended Inline type Exhaust Air fans including accessories such as wire mesh, supports, canvas connection, etc. 1. Vendor needs to rework fan static calculation as per actual shop drawing, motors to be IE3 rated or better 2. Kindly consider panel list for bifurcation of single phase and three phase fans Complying to attached technical specifications

15.7D.1.1 800 CFM Vs 15 mmwg SP Nos 1.00 0

15.7D.2 Supply, Installation, testing & Commissioning of Ceiling Suspended Inline type Fresh Air fans including accessories such as wire mesh, supports, canvas connection, etc. 1. Vendor needs to rework fan static calculation as per actual shop drawing, motors to be IE3 rated or better 2. Kindly consider panel list for bifurcation of single phase and three phase fans Complying to attached technical specifications

15.7D.2.1 800 CFM Vs 15 mmwg SP Nos 1.00 0

15.7E PLANT ROOM & ELECTRICAL ROOM VENTILATION

15.7E.1 Supply, Installation, testing & Commissioning of Ceiling suspended Axial type Exhaust air Fan, with all required mounting (i.e. canvas, wiremesh, supports, etc.) Direct Drive with Motor having capacity of motors to be IE3 rated or better. Fan outlet speed should not be more than 13 -15m/s. Also select the fan dia as mentioned in the HVAC drawing. Complying to attached technical specifications

15.7E.1.1 11800 CFM Vs 25 mmwg SP Nos 1.00 0

15.7E.2 Supply, Installation, testing & Commissioning of Ceiling suspended Axial type Fresh air Fan, with all required mounting (i.e. canvas, wiremesh, supports, etc.) Direct Drive with Motor having capacity of motors to be IE3 rated or better. Fan outlet speed should not be more than 13 -15m/s. Also select the fan dia as mentioned in the HVAC drawing. Complying to attached technical specifications

15.7E.2.1 11200 CFM Vs 25 mmwg SP Nos 1.00 0

15.7F PAINT & SPRAY ROOM VENTILATION

15.7F.1 Supply, Installation, testing & Commissioning of Ceiling suspended Axial Fresh air Fan, with all required mounting (i.e. canvas, wiremesh, supports, etc.) with Motor outside of air stream, having capacity of motor to be IE3 rated or better. G-4 filtration required. Additional filtrations if required will be specified at later stage. Complying to attached technical specifications

15.7F.1.1 7300 CFM Vs 25 mmwg SP Nos 1.00 0

15.7F.2 Supply, Installation, testing & Commissioning of Ceiling suspended Axial type Exhaust air Fan, with all required mounting (i.e. canvas, wiremesh, supports, etc.) Direct Drive with Motor having capacity of motors to be IE3 rated or better. Fan outlet speed should not be more than 13 -15m/s. Also select the fan dia as mentioned in the HVAC drawing. Complying to attached technical specifications

15.7F.2.1 3100 CFM Vs 50mmwg SP Nos 1.00 0

15.7G KITCHEN VENTILATION

15.7G.1 Supply, Installation, Testing & Commisioning of Double Skin Direct Stage Evaporative Cooling Unit (Air Washer) with Thermal Break Profile, including Inlet Louvers, EU - 4 Pre - Filter, 300 mm Deep Cellulose Pad Evaporative Cooler, Water Pumps (1 + 1), SS Sump, Plug Fan with VFD or Fan with EC Motor, Motor of IE3 Efficiency or better, Distribution header, Bypass with Valve including Supply air Plenum, In-built Starter Panel & Control. Complying to attached technical specifications for Evaporative Cooling Units and having following capacity :

15.7G.1.1 17500 CFM Vs 75 mm SP Nos 1.00 0

15.7G.2 Supply, Installation, testing & Commissioning of Floor mounted Axial type Fresh Air Fan,with all required mounting (i.e. canvas, wiremesh, supports, etc.) Direct Drive with Motor. Vendor needs to rework fan static calculation as per shop drawing motors to be IE3 rated or better fan outlet speed should not be more than 13 -15m/s. Also select the fan dia as mentioned in the HVAC drawing. Complying to attached technical specifications Having Capacity as follows:

15.7G.2.1 6300 CFM Vs 25 mm SP Nos 1.00 0

15.7G.3 Supply, Installation & Testing of U/V Filters for water in recirculation line for ECU, with isolation and bypass Complying to attached technical specifications

15.7G.4 Supply, Installation & Testing of Clamp On Magnetic Water Conditioners in Make up line. Complying to attached technical specifications

15.7G.5 Supply and Installation of Ball Valve for ECU in Make-up Line 25 NB Dia Complying to attached technical specifications Nos 1.00 0

15.7G.6 Supply, Installation, testing & Commissioning of Floor Mounted Cabinet Exhaust Unit with Electrostatic Precipatator (ESP) for Kitchen Exhaust with all required mounting (i.e. canvas, wiremesh, supports, etc.) SISW Type fan with Belt Drive with Motor outside airstream Vendor needs to rework fan static calculation as per shop drawing motors to be IE3 rated or better With Weather Protective Rating & Canopy for Terrace Mounting Complying to attached technical specifications Unit Having Capacity as follows:

15.7G.6.1 19200 CFM Vs 100 mmwg SP Nos 1.00 0

15.7G.6.2 7150 CFM Vs 50 mmwg SP Nos 1.00 0

15.7H VENTILATION OF OTHER UTILITY AREAS

15.7H.1 Supply, Installation, testing & Commissioning of Wall Mounted Type Propeller Exhaust Air fan Complete with any required accessories including weather protective louver as per weather protective louver technical specifications attached. Fan Dia to be suitable for below mentioned Exhaust flow

15.7H.1.1 1000 CFM Vs. 10mm SP Nos 1.00 0

15.7H.2 Supply, Installation, testing & Commissioning of Ceiling Suspended type Cabinet Exhaust Air Fans, with all required mounting (i.e. canvas, wiremesh, supports, etc.) Direct Drive with Motor. Vendor needs to rework fan static calculation as per shop drawing motors to be IE3 rated or better fanoutlet speed should not be more than 13-15m/s. Also select the fan dia as mentioned in the HVAC drawing.

15.7H.2.1 1600 CFM Vs 25mm wg SP Nos 1.00 0

15.7H.2.2 1700 CFM Vs 25mm wg SP Nos 1.00 0

15.7H.2.3 4650 CFM Vs 20mm wg SP Nos 1.00 0

15.7H.3 Supply, Installation, testing & Commissioning of Ceiling Suspended type Inline Exhaust Air Fans, with all required mounting (i.e. canvas, wiremesh, supports, etc.) Direct Drive with Motor. Vendor needs to rework fan static calculation as per shop drawing motors to be IE3 rated or better fanoutlet speed should not be more than 13-15m/s. Also select the fan dia as mentioned in the HVAC drawing.

15.7H.3.1 300 CFM Vs 15mm wg SP Nos 1.00 0

15.7H.3.2 600 CFM Vs 20mm wg SP Nos 1.00 0

15.7H.4 Supply, Installation, testing & Commissioning of Ceiling Suspended type Cabinet Fresh Air Fans, with all required mounting (i.e. canvas, wiremesh, supports, etc.) Direct Drive with Motor. Vendor needs to rework fan static calculation as per shop drawing motors to be IE3 rated or better fanoutlet speed should not be more than 13 -15m/s. Also select the fan dia as mentioned in the HVAC drawing.

15.7H.4.1 2500 CFM Vs 25 mmwg SP Nos 1.00 0

15.7H.4.2 2100 CFM Vs 25 mmwg SP Nos 2.00 0

15.7H.4.3 6000 CFM Vs 20 mmwg SP Nos 1.00 0

15.7H.4.4 3800 CFM Vs 25 mmwg SP Nos 1.00 0

15.7H.4.5 3800 CFM Vs 15 mmwg SP Nos 1.00 0

15.7H.5 Supply, Installation, testing & Commissioning of Ceiling Suspended type Inline Fresh Air Fans, with all required mounting (i.e. canvas, wiremesh, supports, etc.) Direct Drive with Motor. Vendor needs to rework fan static calculation as per shop drawing motors to be IE3 rated or better fanoutlet speed should not be more than 13 -15m/s. Also select the fan dia as mentioned in the HVAC drawing.

15.7H.5.1 300 CFM Vs 15mm wg SP Nos 1.00 0

15.7H.5.2 150 CFM Vs 15mm wg SP Nos 1.00 0

15.7H.5.3 600 CFM Vs 20mm wg SP Nos 1.00 0

15.7I COMMON ITEM RELATED TO VENTILATION SYSTEMS

15.7I.1 Supply, Installation, testing & Commissioning of Power Distribution Panel for HVAC systems with incoming Isolator, and Outgoing MCBs, with Intelligent Power Meter for display of Voltages, Current And Power, with Totalizer, and Voltage Sensor HVAC Panel to have provison of auto tripping and restart on receipt of fire signal. Certain panels to have provision for both Emergency and Normal Power supply and changover based on actual requirement. Common Outgoing feeders for following HVAC equipment: Feeders including spares and provisions to be cross verified with HVAC Panel List and HVAC Electrical SLD Complying to attached technical specifications.

15.7I.1.1 HVAC Panel 01 Nos 1.00 0

15.7I.1.2 HVAC Panel 04 Nos 1.00 0

15.7I.1.3 HVAC Panel 29 Nos 1.00 0

15.8 PART VIII - COMMON ITEMS ACROSS AC & VENTILATION SYSTEMS

15.8A COMMON AIR DISTRIBUTION ITEMS

15.8A.1 Supply, Installation and testing of G. I. Rectangular Type Ducting with TDC/TDF Flanges, 3M tapes on Joints, Wired Supports with Sesmic Rating suitable for use within Earthquake Zone IV, having intermediate rigid supports, rated for 2" Duct Pressure as per SMACNA 2012 Complying to attached technical specifications for GI Ducting.

15.8A.1.1 24G Thickness Sqm 6,578.00 0

15.8A.1.2 22G Thickness Sqm 4,585.00 0

15.8A.1.3 20G Thickness Sqm 1,361.00 0

15.8A.1.4 18G Thickness Sqm 305.00 0

15.8A.2 Supply & Installation of Extruded Aluminium Powder Coated Weather Louver for Fresh Air, Complying to Technical Specifications Attached | RAL colour need to be coordinated before ordering

15.8A.2.1 1500 X 700 listed size Nos 1.00 0

15.8A.2.2 1600 X 900 listed size Nos 1.00 0

15.8A.2.3 750 X 300 listed size Nos 1.00 0

15.8A.2.4 700 X 300 listed size Nos 2.00 0

15.8A.2.5 400 X 250 listed size Nos 1.00 0

15.8A.2.6 1650 X 800 listed size Nos 2.00 0

15.8A.2.7 1000 X 500 listed size Nos 2.00 0

15.8A.2.8 700 X 500 listed size Nos 1.00 0

15.8A.2.9 300 X 200 listed size Nos 2.00 0

15.8A.2.10 1000 X 600 listed size Nos 1.00 0

15.8A.2.11 1400 X 600 listed size Nos 1.00 0

15.8A.2.12 1500 X 650 listed size Nos 1.00 0

15.8A.2.13 3600 X 1300 listed size Nos 1.00 0

15.8A.2.14 500 X 250 listed size Nos 1.00 0

15.8A.2.15 300 X 150 listed size Nos 1.00 0

15.8A.2.16 1500 X 750 listed size Nos 1.00 0

15.8A.2.17 600 X 250 listed size Nos 1.00 0

15.8A.2.18 1500 X 550 listed size Nos 2.00 0

15.8A.2.19 600 X 350 listed size Nos 1.00 0

15.8A.2.20 1250 X 550 listed size Nos 2.00 0

15.8A.2.21 1700 X 800 listed size Nos 1.00 0

15.8A.3 Supply & Installation of Extruded Aluminium Powder Coated Weather Louver for Exhaust Air, Complying to Technical Specifications Attached

15.8A.3.1 1500 X 700 listed size Nos 1.00 0

15.8A.3.2 750 X 300 listed size Nos 1.00 0

15.8A.3.3 1000 X 500 listed size Nos 1.00 0

15.8A.3.4 1000 X 600 listed size Nos 1.00 0

15.8A.3.5 1000 X 400 listed size Nos 5.00 0

15.8A.3.6 1200 X 400 listed size Nos 1.00 0

15.8A.3.7 1650 X 800 listed size Nos 1.00 0

15.8A.3.8 250 X 200 listed size Nos 1.00 0

15.8A.3.9 400 X 250 listed size Nos 2.00 0

15.8A.3.10 500 X 200 listed size Nos 2.00 0

15.8A.3.11 700 X 500 listed size Nos 1.00 0

15.8A.3.12 1200 X 750 listed size Nos 1.00 0

15.8A.3.13 400 X 200 listed size Nos 1.00 0

15.8A.3.14 500 X 250 listed size Nos 1.00 0

15.8A.3.15 1000 X 350 listed size Nos 1.00 0

15.8A.3.16 600 X 250 listed size Nos 1.00 0

15.8A.3.17 800 X 350 listed size Nos 3.00 0

15.8A.3.18 600 X 300 listed size Nos 1.00 0

15.8A.3.19 750 X 400 listed size Nos 1.00 0

15.8A.4 Supply & Installation of Extruded Aluminium Powder Coated Supply Air Grilles with VCD, Complying to Technical Specifications Attached

15.8A.4.1 700 X 350 listed size Nos 4.00 0

15.8A.4.2 400 X 400 listed size Nos 3.00 0

15.8A.4.3 500 X 500 listed size Nos 4.00 0

15.8A.4.4 600 X 600 listed size Nos 11.00 0

15.8A.4.5 1200 X 150 listed size Nos 3.00 0

15.8A.4.6 1800 X 150 listed size Nos 1.00 0

15.8A.4.7 2400 X 150 listed size Nos 13.00 0

15.8A.4.8 3000 X 150 listed size Nos 21.00 0

15.8A.5 Supply & Installation of Extruded Aluminium Powder Coated Return Air Grilles Complying to Technical Specifications Attached

15.8A.5.1 700 X 350 listed size Nos 4.00 0

15.8A.5.2 400 X 400 listed size Nos 4.00 0

15.8A.5.3 500 x 500 listed size Nos 3.00 0

15.8A.5.4 600 X 600 listed size Nos 12.00 0

15.8A.5.5 300 X 300 listed size Nos 4.00 0

15.8A.6 Supply & Installation of Extruded Aluminium Powder Coated Exhaust Air Grilles Complying to Technical Specifications Attached

15.8A.6.1 400 X 400 listed size Nos 2.00 0

15.8A.6.2 500 X 500 listed size Nos 1.00 0

15.8A.6.3 700 X 350 listed size Nos 24.00 0

15.8A.7 Supply & Installation of Extruded Aluminium Powder Coated Double Deflection Supply Air Grilles with VCD, Complying to Technical Specifications Attached

15.8A.7.1 600 X 600 listed size Nos 22.00 0

15.8A.8 Supply, Installation and testing of Inter connecting Insulated Flexible Circular Ducting Complying to attached technical specifications

15.8B COMMON CABLING & CABLE TRAYS

15.8B.1 Supply, Installation, testing and commissioning of Copper conductor cables XLPE insulated / FRLS multistrand Cu. Conductor armoured / unarmoured cables ( As per IS 1554 & IS 7098) PVC insulated, Multistrand armoured cable of 1.1KV grade with termination glands and identification tags, clamps, and saddles. GI earthing (flats / strips / wires, as may be applicable as per, electric rules : Earthing system shall comply to IS: 3043-1987.)

15.8B.1.1 4C x 1.5 Sqmm YWY Cable Rmt 875.00 0

15.8B.1.2 4C X 2.5 Sq.mm YWY Cable Rmt 350.00 0

15.8B.1.3 4C X 4 Sq.mm YWY Cable Rmt 45.00 0

15.8B.1.4 4C X 6 Sq.mm YWY Cable Rmt 335.00 0

15.8B.1.5 4C X 10 Sq.mm YWY Cable Rmt 235.00 0

15.8B.2 Supply, Installation, testing and commissioning of Aluminium conductor cables XLPE / FRLS multistrand Al. Conductor armoured / unarmoured cables ( As per IS 1554 & IS 7098) PVC insulated, Multistrand armoured cable of 1.1KV grade with termination glands and identification tags, clamps, and saddles. GI earthing (flats / strips / wires, as may be applicable as per, electric rules : Earthing system shall comply to IS: 3043-1987.) ( Vendor to Select Sizes as per Chiller OEM Requirement)

15.8B.2.1 3.5C X 2 runs x 240 Sq.mm. Cable Rmt 70.00 0

*Need to re-check Cable size requirement with Chiller OEM and change the same if required.

15.8B.3 Supply, Installation, Testing and Commissioning of Signal/Sensor Cabling (2Cx1.5 mm Copper FRLS) Complying to attached technical specifications Rmt 13,960.00 0

15.8B.4 Supply, Installation, Testing and Commissioning of Communication Cabling for HVAC BMS and VRV System (2Cx1.5 sqmm Copper FRLS), In 25mm Dia Conduits, UV Stabilized, Complying to attached technical specifications Rmt 20,940.00 0

15.8B.5 Supply & Installation of G. I. Cable Tray with Tray Cover for Chiller Plant and all HVAC System related services as deemed required. Tray to be in GI, perforated type with minimum 14G thickness, equipped with tray cover in external areas (tray cover to be in 14G GI and to have a plain finish) To Comply with Attached Technical Specifications for Cable Tray

Note: Quantity of cable trays have been roughly estimated, same need to be calculated based on finalized cable tray routings within the project

15.8B.5.2 350 mm X 50 mm Rmt 0

15.8C OTHER COMMON ITEMS

15.8C.1 Supply, Installation, Testing and Commissioning of Provision of fire stop mortar system for 250 ° C X 2 Hrs Rating, when tested in accordance with UL 1479/ASTM-E 814 standards, suitable for closing all gaps of penetration for HVAC services passing across fire rated partitions, the mortar assembly shall be light weight and having environmental testing and mold resistance certification / rating Note: Exact quantity requirement for the same is not available at this stage of the project, however, this will need to be provided at all locations where HVAC services are crossing fire rated compartments

15.8C.1.1 Mortar assembly suitable for closure of medium to large size gaps Sqm 150.00 0

15.8C.1.2 Mortar assembly suitable for closure of circular gaps upto 2" Sqm 40.00 0

15.9 PART IX- HVAC BMS

15.9A DDC/ PLC CONTROLLERS

15.9A.1 Supply, Installation, testing & Commissioning of Direct Digital Controllers (DDCs) for Air Handling Systems, Control, Monitoring & Switching On / Off of other respective low-side HVAC Equipment as applicable Complying to technical specifications attached, Refer to HVAC BMS IO Summary for reference of IO points to be covered including the spares requirements per DDC Panels to be provided for housing DDCs along with all internal fitting, equipment, terminals and cabling. DDC to have required provisions for integration with Centralized BMS via BACnet / Modbus

15.9A.2 Supply, Installation, testing & Commissioning of PID Controllers for Pressurization Systems, Control, Monitoring & Switching On / Off as applicable Complying to technical specifications attached Refer to HVAC BMS IO Summary for reference of IO points to be covered including the spares requirements per Pressurization related PID controller PID Controller to have required provisions required for remote monitoring through BMS

15.9A.2.1 PID Controller for Staircase 01, Liftwell S1 & S2 - Pressurization System Set 1.00 0

15.9A.2.2 PID Controller for Staircase 02, 03, Liftwell N2 & N3 - Pressurization System Set 1.00 0

15.9A.2.3 PID Controller for Staircase E1 Pressurization System Set 1.00 0

15.9A.2.4 PID Controller for Staircase E2, Liftwell E3 - Pressurization System Set 1.00 0

15.9A.3 Supply, Installation, testing & Commissioning of Intergated Plant Manager & Optimizer to control chillers, CHW pumps, cond Pumps, Cooling tower fan, on/ off valves and sensors mentioned below: 350 TR X 2 No. Chiller Plant (W) , 350 TR X 1 No. Chiller Plant (S) , Variable Flow Primary Pumps (2W + 1S) , Variable Flow Condenser Pumps (2W + 1S) , 350 TR x 3 nos. Cooling Towers (2W+1S) inclusive of all transmitters and control elements as per Highside P&ID plant manager scope & IO summary HVAC automation system needs to have BACnet IP / Modbus RS485 compatibility. BACnet IP will be preferred as it is an open protocol and having less lag. Complying to attached HVAC Highside PID, BMS HVAC IO Summary for Chiller Plant Set 1.00 0

15.9A.4 Supply, Installation, testing commissioning of Hand Held Operators Terminal for Monitoring all DDC / PLC Automated Control Systems. (1 portable hand-held terminal considered per building. The hand held operator terminal to have display and to be capable for integration with all the controllers in the project Nos 2.00 0

15.9A.5 Supply, Installation, Testing and Commissioning of Hardware and Software for : a) Controllers / PLC, b) Communications, c) SCADA d) Modbus Gateway Complying to applicable technical specifications attached Lumpsum 1.00 0

15.9A.6 Installation, debugging, testing, commissioning, validation and documentation of entire HVAC BMS System inclusive of all above mentioned software, hardware and below mentioned field devices, cabling, etc. Lumpsum 1.00 0

15.9B HVAC TRANSMITTERS - FIELD DEVICES

15.9B.1 Supply, Installation, Testing and Commissioning of Combined Room Mounted Type Air Temp & Relative Humidity Transmitter with temperature range of 0 - 50ºC and RH range of 0 – 100% with required test certificate / field calibration and Complying to attached technical specification Nos 47.00 0

15.9B.2 Supply, Installation, Testing and Commissioning of Outdoor Air Temperature Transmitter 0 - 50ºC with required test certificate / field calibration certificate and Complying to attached technical specifications Nos 1.00 0

15.9B.3 Supply, Installation, Testing and Commissioning of Outdoor Air RH Transmitter 0 – 100% with required test certificate / field calibration certificate and Complying to attached technical specifications Nos 1.00 0

15.9B.4 Supply, Installation, Testing and Commissioning of Water Level Transmitter 0-1000 mm with required test certificate / field calibration certificate and Complying to attached technical specifications Nos 4.00 0

15.9B.5 Supply, Installation, Testing and Commissioning of Pipe Water Temperature Transmitter 0 - 50ºC with required test certification / field calibration certificate and Complying to attached technical specifications Nos 16.00 0

15.9B.6 Supply, Installation, Testing and Commissioning of Pipe Water Pressure Transmitter 0 - 10 kg /cm2 with required test certification / field calibration certificate and Complying to attached technical specifications Nos 10.00 0

15.9B.7 Supply, Installation, Testing and Commissioning of Room Mounted Type Air Temp Transmitter 0 - 50ºC with required test certificate / field calibration and Complying to attached technical specification Nos 19.00 0

15.9B.8 Supply, Installation, Testing and Commissioning of Duct Mounted Type Air Temp Transmitter 0 - 50ºC, with minimum 450 mm Long probe with required test certificate / field calibration and Complying to attached technical specifications Nos 15.00 0

15.9B.9 Supply, Installation, Testing and Commissioning of Duct Mounted Type Air RH Transmitter 0 – 100%, with minimum 450 mm Long probe with required test certificate / field calibration certificate and Complying to attached technical specifications Nos 1.00 0

15.9B.10 Supply, Installation, Testing and Commissioning of AHU Mounted Type Air Temp Transmitter 0 - 50ºC, 450 mm Long Probe (For Coil Off Control) with required test certificate / field calibration and Complying to attached technical specifications Nos 14.00 0

15.9B.11 Supply, Installation, Testing and Commissioning of Air Differential Pressure Switch with adjustable pressure setting, operating temperature range of 0-50ºC and operating pressure up to 250 mm WC, Suitable for high and low trips, having automatic reset provisions Complying to attached technical specifications

15.9B.11.1 Differential Pressure Switch (Across EU-4 Filters) Nos 40.00 0

15.9B.11.2 Differential Pressure Switch (Across EU-8 Filters) Nos 40.00 0

15.9B.12 Supply, Installation, Testing and Commissioning of Air Differential Pressure Transmitters, operating temperature range of 0-50ºC, rated for Differential Pressure Range of 0 - 150 mm for measurement of differential pressure across AHU fan blowers. Complying to attached technical specifications Nos 41.00 0

15.9B.13 Supply, Installation, Testing and Commissioning of IAQ monitors with required test certificate / field calibration certificate and Complying to attached technical specifications *Considered for high density common areas* Nos 20.00 0

TOTAL OF HVAC WORKS 0

16.1 HORTICULTURE

16.1.1 SITE CLEANING

Site cleaning in areas as directed including removing of weed ,cutting grasses , disposing off the material with lead upto 50 m as directed by site incharge etc. complete Sqm 7,125.40 0

16.1.2 MURRUM FILLING

Providing and Filling with Murum in layers to required depths as directed, including watering, ramming and compacting dry density, including carrying out Laboratory 'Proctor Density' Test, etc. complete as directed by site incharge.( Consolidated thickness will be considered for payment.)

16.1.2a Murum available at site within 10m Cum 81.00 0

16.1.2b Murum brought from outside Cum 1.00 0

16.1.3 SURFACE DRESSING

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50m and lift up to 1.5 m.

In All kinds of soil. Sqm 7,517.00 0

16.1.4 LAWN ( Refer point 7.0 from specifications)

Providing & mixing earth & manure as/specification & spreading to a thickness of 300mm. Flooding the ground with water & making kiaries & dismantling the same. Fine dressing the ground to levels specified etc. complete as directed. Planting grass of specified specie as per specification & maintening the same till the grass developes a mat etc complete.

16.1.4a Stenotaphrum secundatum (Excluding grass cost) Sqm 135.00 0

16.1.4b Cynadon dacttylon ( Excluding grass cost) Sqm 46.00 0

16.1.5 SHRUBS, CLIMBERS & GRASSES PLANTATION ON GROUND ( Refer point 6.0 from specifications)

Providing & mixing earth & manure, pesticides as per specification Filling mixture of earth & manure in shrub bed to a specified depth, flooding with water & leveling & Planting. etc complete as directed.( Excluding plant cost )

16.1.5a 600mm depth Sqm 3,586.00 0

16.1.6 FLOWER BED, PERENNIAL PLANTATION ON GROUND ( Refer point 8.0 from specifications)

Providing & mixing earth & manure, Pesticides as per specification Filling mixture of earth & manure in Ground cover bed to a specified depth, flooding with water & leveling & Planting. etc complete as directed.( Excluding plant cost )

16.1.6a 300mm depth Sqm 736.01 0

16.1.7 LAWN, SHRUBS, & GRASSES PLANTATION ON SLAB ( Refer point 9.0 & 9.2 from specifications)

Providing, preparing and filling planting medium as per specification including watering, flooding, dressing, planting as per plan and specification etc.

16.1.7a 200mm depth Sqm 90.00 0

16.1.7b 300mm depth Sqm 600.00 0

16.1.7c 450mm depth Sqm 55.00 0

16.1.7d 600mm depth Sqm 414.00 0

16.1.7e 750mm depth Sqm 141.00 0

16.1.7f 900mm depth Sqm 440.00 0

16.1.8 POTTED PLANTS ( Refer point 9.0 & 9.1 from specifications)

Providing and filling pots with planting media as/specification excluding pot cost, placing as diected, etc complete

16.1.8a 1200mmx500mm and 425mm depth Nos 62.00 0

16.1.8b 700x700mm and 675mm depth Nos 7.00 0

16.1.9 TREES ON GROUND ( Refer point 5.0 from specifications)

Providing & mixing earth & manure, pesticides as per specification Filling mixture of earth & manure in bed to a minimum depth as per pit size flooding with water & leveling,inserting supporting stakes etc complete as directed.( Excluding plant cost )

16.1.10 TREES ON SLAB ( Refer point 9.0 and 9.2 from specifications)

Providing, preparing and filling planting medium as per specification including watering, flooding, dressing, planting as per plan and specification etc.

16.1.11 TRANSPLANTATION OF TREES ( Refer point 10.0 & 11.0 from specifications)

Transplantation of trees within site including excavation around existing tree, pruning of branches, lifting, loading and transportation of existing tree, digging pits for placing tree at new place, adding manure,and, fertilizer, hormones and bio fertilizer to it. Levelled and neatly dressedand disposal of surplus materials from old existing and new sites to designated place. Each tree should be firmly secured to the stake so as to prevent excessive movement, flooding with water, treatment of roots, ropeand gunny bags as per direction of the officer incharge. T&P and all requiredmaterials shall be arranged by the contractor and nothing extra shall bepaid on this account. Girth of tree shall be measured at a height of 1m above ground level.

16.1.11a Girth of trees upto 700MM Nos 140.00 0

16.1.11b Girth of trees beyond 700MM Nos 103.00 0

16.1.12 TREE CUTTING ( Refer point 12.0 from specifications)

Felling trees of the girth (measured at a height of 1 m above ground level),including cutting of trunks and branches, removing the roots and disposal.

16.1.12a Girth of trees upto 700MM Nos 10.00 0

16.1.12b Girth of trees beyond 700MM Nos 16.00 0

16.1.13 SOIL BROUGHT FROM OUTSIDE

Providing and supplying soil on site including loading, unloading, transportation, stacking and protection from rain and contamination, lead upto 300m till use etc. complete

16.1.13a Good red soil for planting Cum 1.00 0

16.1.13b Good poyta soil for planting Cum 1.00 0

16.1.14 MANURE BROUGHT FROM OUTSIDE ( Refer point 2.3 from specifications)

16.1.14a Providing and supplying cow dung manure on site including loading, unloading, transportation, stacking and protection from rain and contamination, lead upto 300m till use etc. complete Cum 1.00 0

16.1.15 JKD EDGING ( Refer point 2.7 from specifications)

16.1.15a Providing & laying JKD make HDPE line edging 150mm in proper line & level including cutting ,fixing etc. complete as directed by site incharge. Rmt 334.30 0

16.1.16 BRICK BAT ( Refer point 2.4 from specifications)

16.1.16a Providing & laying drainage media of 75 mm thick loose brick bat of approved quality including topping with filling crevices with coarse sand about 25 mm above brick bat, etc. complete as directed. Cum 10.00 0

16.1.17 LAYING OF COIR MAT ( Refer point 2.5 from specifications)

16.1.17a For slopes as per design & specification, providing and laying woven Coir Matt of 700 GSM of 1cm X 1 cm grid of approved size, specification and make,in specified area as per drawing, including spreading to line, overlapping, cutting as required, pinning with 8" deep GI/Tor steel clip/pins, etc all complete as directed. Sqm 2,751.00 0

16.1.18 GEOTEXTILE ( Refer point 2.6 from specifications)

16.1.18a Providing & laying 150 GSM Geotextile including cutting, 150mm overlapping ,fixing with 'U' hooks etc. complete as directed Sqm 3,628.00 0

16.1.19 PLANTS ( Refer point 2.1 from specifications)

16.1.19a Providing best quality plants as per specification & plant list including transport, loading, unloading, protection, etc. complete - as per the following list of trees, shrubs, ground covers, climbers and lawn grass

16.1.20.1 SWIETENIA MAHOGANY /SCHLEICHERA OLEOSA Nos 4.00 0

16.1.20.2 MADHUCA LONGIFOLIA Nos 1.00 0

16.1.20.3 DALBERGIA SISSOO Nos 22.00 0

16.1.20.4 ALBIZIA LEBBECK Nos 1.00 0

16.1.20.5 ERYTHRINA INDICA Nos 5.00 0

16.1.20.6 FICUS VIRENS Nos 6.00 0

16.1.20.7 MITRAGYNA PARVIFOLIA Nos 29.00 0

16.1.20.8 ALSTONIA SCHOLARIS Nos 14.00 0

16.1.20.9 COCHLOSPERMUM GOSSYPIUM Nos 5.00 0

16.1.20.10 TABEBUIA AVELLANEDAE Nos 15.00 0

16.1.20.11 TERMINALIA MANTALY Nos 3.00 0

16.1.20.12 PLUMERIA ACUTIFOLIA Nos 1.00 0

16.1.20.13 DALBERGIA LANCEOLARIA Nos 22.00 0

16.1.20.14 ALBIZIA ODORATISSIMA Nos 10.00 0

16.1.20.15 ANOGEISSUS LATIFOLIA Nos 11.00 0

16.1.20.16 PONGAMIA PINNATA Nos 15.00 0

16.1.20.17 BOMBAX CEIBA Nos 6.00 0

16.1.20.18 TERMINALIA ARJUNA/TERMINALIA BELLIRICA Nos 3.00 0

16.1.20.19 CRATAEVA NURVALA Nos 2.00 0

16.1.20.20 FIRMIANA COLORATA Nos 1.00 0

16.1.20.21 WRIGHTIA ARBOREA Nos 17.00 0

16.1.20.22 SARACA ASOCA Nos 4.00 0

16.1.20.23 BAUHINIA ACUMINATA Nos 6.00 0

16.1.20.24 EHRETIA LAEVIS Nos 6.00 0

16.1.20.25 AZADIRACHTA INDICA Nos 11.00 0

16.1.20.26 DENDROCALAMUS STRICTUS Nos 125.00 0

16.1.20.27 BUTEA MONOSPERMA Nos 135.00 0

16.1.20.28 ALANGIUM SALVIIFOLIUM Nos 125.00 0

16.1.20.29 MALLOTUS PHILIPPENSIS Nos 130.00 0

16.1.20.30 BAUHINIA RACEMOSA Nos 157.00 0

16.1.20.31 ALANGIUM SALVIIFOLIUM Nos 137.00 0

16.1.20.32 MALLOTUS PHILIPPENSIS Nos 129.00 0

16.1.20.33 LANNEA COROMANDELICA Nos 12.00 0

16.1.20.34 BOSWELLIA SERRATA Nos 22.00 0

16.1.20.35 MORINDA PUBESCENS Nos 13.00 0

16.1.20.36 ALANGIUM SALVIIFOLIUM/ CRATAEVA NURVALA Nos 22.00 0

16.1.20.37 AEGLE MARMELOS Nos 24.00 0

16.1.20.38 TECOMELLA UNDULATA Nos 13.00 0

16.1.20.39 TECOMA GRANDIS/ TERMINALIA CRENULATA Nos 18.00 0

16.1.20.40 BUTEA MONOSPERMA Nos 20.00 0

16.1.20.41 MORINDA TINCTORIA Nos 21.00 0

16.1.20.42 OROXYLUM INDICUM/ WRIGHTIA ARBOREA Nos 19.00 0

16.1.20.43 AEGLE MARMELOS Nos 21.00 0

16.1.20.44 COCHLOSPERMUM RELIGIOSUM Nos 20.00 0

16.1.20.45 SYZYGIUM CUMINI Nos 116.00 0

16.1.20.46 FICUS RACEMOSA Nos 121.00 0

16.1.20.47 ACACIA NILOTICA Nos 120.00 0

16.1.20.48 DENDROCALAMUS STRICTUS Nos 234.00 0

16.1.20.49 CRATAEVA NURVALA Nos 120.00 0

16.1.20.50 BAMBUSA ARUNDINACEA Nos 122.00 0

16.1.20.51 HOLARRHENA ANTIDYSENTERICA Nos 5.00 0

16.1.20.52 WOODFORDIA FRUTICOSA Nos 86.00 0

16.1.20.53 ALANGIUM SALVIIFOLIUM Nos 3.00 0

16.1.20.54 HELICTERES ISORA Nos 19.00 0

16.1.20.55 BAUHINIA TOMENTOSA Nos 14.00 0

16.1.20.56 VITEX NEGUNDO Nos 29.00 0

16.1.20.57 CASSIA AURICULATA Nos 41.00 0

16.1.20.58 CALOTROPIS PROCERA Nos 29.00 0

16.1.20.59 ADHATODA VASICA Nos 20.00 0

16.1.20.60 PLUMERIA ACUTIFOLIA Nos 11.00 0

16.1.20.61 FICUS SP Nos 6.00 0

16.1.20.62 RADERMACHERA Nos 4.00 0

16.1.21.1 DODONAEA VISCOSA Nos 922.00 0

16.1.21.2 LAWSONIA ALBA Nos 1,393.00 0

16.1.21.3 TABERNAEMONTANA CORONARIA DWARF Nos 397.00 0

16.1.21.4 HIBISCUS ROSA SINENSIS Nos 195.00 0

16.1.21.5 SPHAGNETICOLA TRILOBATA/STENOTAPHRUM SECUNDATUM Nos 1,023.00 0

16.1.21.6 BARLERIA CRISTATA BLUE Nos 94.00 0

16.1.21.7 CYMBOPOGON CITRATUS Nos 1,578.00 0

16.1.21.8 VETIVER ZIZANIOIDES Nos 136.00 0

16.1.21.9 POGONATHERUM PANICEUM Nos 450.00 0

16.1.21.10 CYMBOPOGON NARDUS Nos 144.00 0

16.1.21.11 BARLERIA PRIONITIS Nos 707.00 0

16.1.21.12 MIMOSA HAMATA Nos 162.00 0

16.1.21.13 POGONATHERUM PANICEUM/ PHYLLANTHUS MYRTIFOLIUS Nos 1,991.00 0

16.1.21.14 ANGELONIA ANGUSTIFOLIA/RUELLIA LORENTZIANA Nos 286.00 0

16.1.21.15 DICHANTHIUM ANNULATUM /ACORUS CALAMUS Nos 170.00 0

16.1.21.16 BLUMEA ERIANTHA Nos 297.00 0

16.1.21.17 SIDA ACUTA / TURNERA ULMIFOLIA Nos 198.00 0

16.1.21.18 KALANCHOE BIPINNATA Nos 453.00 0

16.1.21.19 JUSTICIA GENDARUSSA Nos 352.00 0

16.1.21.20 ACORUS CALAMUS/EQUISETUM HYEMALE/THYSANOLAENA LATIFOLIA Nos 440.00 0

16.1.21.21 ABUTILON INDICUM Nos 60.00 0

16.1.21.22 PLUMBAGO ZEYLANICA Nos 429.00 0

16.1.21.23 PENTAS (RED) Nos 162.00 0

16.1.21.24 ANGELONIA GRANDIFLORA Nos 93.00 0

16.1.21.25 VINCA ROSEA ALBA Nos 177.00 0

16.1.21.26 POGONATHERUM CRINITUM Nos 316.00 0

16.1.21.27 CROSSANDRA NIDIBULI FORMIS Nos 28.00 0

16.1.21.28 RULIEA LONDRINA (PURPLE) Nos 69.00 0

16.1.21.29 KALANCHOE PINNATA Nos 41.00 0

16.1.21.30 MURRAYA PANICULATA Nos 380.00 0

16.1.21.31 BAMBUSA MULTIPLEX Nos 44.00 0

16.1.21.32 PHYLLANTHUS MYRTIFOLIUS Nos 447.00 0

16.1.21.33 HYMENOCALLIS LITTORALIS Nos 24.00 0

16.1.21.34 TABERNAEMONTANA CORONARIA Nos 95.00 0

16.1.21.35 VITEX NEGUNDO Nos 239.00 0

16.1.21.36 GREWIA TENAX Nos 555.00 0

16.1.21.37 MAYTENUS EMARGINATA/ HOLARRHENA ANTIDYSENTERICA Nos 258.00 0

16.1.21.38 SACCHARUM MUNJA Nos 3,211.00 0

16.1.21.39 WOODFORDIA FRUTICOSA Nos 13.00 0

16.1.21.40 HELICTERES ISORA Nos 38.00 0

16.1.21.41 GREWIA ASIATICA Nos 27.00 0

16.1.21.42 APLUDA MUTICA Nos 109.00 0

16.1.21.43 SENNA SPECTABILIS Nos 172.00 0

16.1.21.44 GREWIA TENAX/ WOODFORDIA FRUTICOSA Nos 22.00 0

16.1.21.45 CALOTROPIS PROCERA Nos 44.00 0

16.1.21.46 CHRYSOPOGON FULVUS Nos 119.00 0

16.1.21.47 CLERODENDRUM PHLOMIDIS Nos 209.00 0

16.1.21.48 FICUS HISPIDA Nos 230.00 0

16.1.22 CLIMBERS

16.1.22.1 VENTILAGO DENTICULATA Nos 43.00 0

16.1.22.2 CLEMATIS HEDYSARIFOLIA Nos 31.00 0

16.1.22.3 LONICERA JAPONICA Nos 8.00 0

16.1.22.4 IPOMOEA/THUMBERGIA LAURIFOLIA Nos 39.00 0

16.1.22.5 ARGYREIA NERVOSA Nos 54.00 0

16.1.22.6 COMBRETUM ALBIDUM Nos 180.00 0

16.1.22.7 TINOSPORA CORDIFOLIA Nos 38.00 0

16.1.22.8 WATTAKAKA VOLUBILIS Nos 9.00 0

16.1.22.9 CRYPTOLEPIS DUBIA Nos 8.00 0

16.1.22.10 CELASTRUS PANICULATUS Nos 8.00 0

16.1.22.11 IPOMOEA MARGINATA Nos 9.00 0

16.1.22.12 DALBERGIA VOLUBILIS Nos 8.00 0

16.1.22.13 FICUS PUMILA Nos 22.00 0

16.1.22.14 VENTILAGO MADRASPATANA Nos 7.00 0

16.1.23 GRASSES

16.1.23.1 ARACHIS PINTOI Nos 4,250.00 0

16.1.23.2 ACORUS CALAMUS/ANGELONIA Nos 902.00 0

16.1.23.3 PENNISETUM PANICULATUM/ EQUISETUM Nos 869.00 0

16.1.24.1 STENOTAPHRUM SECUNDATUM Sqm 312.00 0

16.1.24.2 CYNODON DACTYLON Sqm 960.00 0

TOTAL OF HORTICULTURE WORKS 0

16.2 IRRIGATION WORK 0.00

16.2.1 Providing, laying & jointing in position HDPE pipe (PE 100) conforming to ISI S : 4984 / 2000 and suitable for the respective working pressures with all butt welded fittings and accessories e.g. couplings, tees, bends, reducers, screwed adapters, flanged tail pieces etc. jointing as per manufacturers' instruction,etc. item complete.

16.2.1.1 HDPE Pipe 90 mm-10 kg/cm2 Rmt 1,300.00 0

16.2.1.2 HDPE Pipe 75 mm-10 kg/cm2 Rmt 600.00 0

16.2.2 Providing, laying, jointing, testing and commissioning of approved make Agriculture PVC Pipes Confirming to IS 4985:2000 laid in wall / on floor / below ceiling in shortlengths for wash hand basin / kitchen sinks to floor trap, including all required PVC fittings as per IS 7834:1987 such as 45⁰ bend / shoe bend, single Y, 87.5° bend, socket, reducer etc. with materials & labour etc. complete, jointing with approved make solvent cement solution & giving watertightness test for pipes laid in the sunken / ceiling portion with making holes in walls / floor grooving & redoing the same and proper clamp / hangers / pedistal supports wherever required necessary etc. complete, as per direction of engineer in charge.

16.2.2.1 PVC pipe 75mm-6 kg/cm2 Rmt 18.00 0

16.2.2.2 PVC pipe 63mm-6 kg/cm2 Rmt 846.00 0